Upload
lamdieu
View
214
Download
0
Embed Size (px)
Citation preview
THE CHOICE IS UP TO YOU!
Both of our Die systems will perform superbly for you. Your requirements will dictate which die system is best.
THE STANDARD IN THE INDUSTRY
Our conventional dies will properly close the button molds so that the covered button will most adequately hold up. They will also enable you to cover buttons with a wide range of materials without die changes.
FOR EXTRA HOLDING STRENGTH
Out Lip-Lok Dies incorporate an internal bevel which interacts with the sleeve bevel thereby permitting the covered shell to roll under the back for a more “POP-PROOF” button. Lip-Lok Buttons are ideal for high volume production.
456 Nordhoff Place, Englewood, NJ 07631 • 201-569-7300 • Fax: 201-569-4112 • www.ccmetal.com • [email protected]
DYNA-LINE BUTTON & DIE
LIP-LOK BUTTON & DIE
UPHOLSTERY PRODUCTS DIVISION
SLEEVE BEVEL
SLEEVE BEVEL
SUPPORT POST
INTERNAL BEVEL ON
SUPPORT POST
DYNA-LINE LIP-LOK
BETTER QUALITY BUTTONS & SUPPLIES MACHINERY, DIES & EQUIPMENT
Made in the USA
UPHOLSTERY PRODUCTS
Serving the needs of the upholstery and allied industries—for almost a century
456 Nordhoff Place, Englewood, NJ 07631 • 201-569-7300 • Fax: 201-569-4112 • www.ccmetal.com • [email protected]
DYNA-LINE is pleased to offer this newest edition of our informative and helpful buyer’s guide to Button-covering and Tufting.
In this guide you will also find most of the hardware items essential to the upholstery business.
Our extensive manufacturing “know-how” and modern production facilities are pledged to produce the widest selection of quality button covering and tufting supplies from a single source, in a complete range for virtually every application in the furniture and allied fields. We employ the latest in “state of the art” equipment for all manufacturing processes; from die-making through stamping and assembly, tempering (hardening and annealing) and the final steps of plating, finishing and inspection.
We would be pleased to submit samples for your testing and approval, and stand ready to work with you in developing new items to your specifications.
QUICK REFERENCE: 1 BUTTON COVERING INFORMATION 1 SHELLS 2 WIRE EYE BACKS 2 HOOK BACKS 2 PRONG (clinch) BACKS 3 NO-DENT BACK NAILS 3 PIVOT BACKS 3 UNASSEMBLED TACK (shells, collets, wads) 4 UPHOLSTERY NAIL BACKS 4 WASHERS 4 SPRING WASHERS 5 NYLON LOOPS (pre-tied) 5 ANCHORS and ANCHOR BUTTONS 5 TUFTING TWINE 6 DETACHABLE BUTTONS (Screw-on) 6 FASHION SHAPED BUTTONS 6 MOLDED BUTTONS (Nylon, One Piece) 7 PRE-ASSEMBLED METAL BUTTONS 7 TUFTING TAPES & COLLETS 7 SWATCH BOOK GROMMETS & WASHERS 8 GROMMETS AND WASHERS 8 EYELETS 8 VENTILATORS and WASHERS 9 SNAP FASTENERS 9 TUFTING NEEDLES 10 PRONG (clinch) INSERTING TOOL 11 UPHOLSTERY NAILS 11 SPRING CLIPS 11 DYNA-GLIDES 12 PART NUMBER ORDERING GUIDE 13 FASTENING HARDWARE 14 MACHINERY 17 DIES
Our products are warranted to be free from defects in material or workmanship. We will replace without charge products found by us to be defective. THIS IS THE SOLE AND EXCLUSIVE
WARRANTY FOR OUR PRODUCTS. “WE EXPRESSLY DISCLAIM ALL OTHER WARRANTIES, EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OR MERCHANTABLITY AND OF FITNESS FOR A PERTICULAR PURPOSE.” In no event shall we be liable to our customer for any general, incidental, special or consequential damages, including any claims for lost profits, arising out of or occasioned by a defect in any product. In no event shall be
we liable for an amount greater than the purchase price of the products.
DYNA-LINE UPHOLSTERY PRODUCTS DIVISION C&C METAL PRODUCTS CORP., 456 Nordhoff Place, Englewood, NJ 07631
456 Nordhoff Place, Englewood, NJ 07631 • 201-569-7300 Fax: 201-569-4112 • www.ccmetal.com • [email protected]
UPHOLSTERY PRODUCTS DIVISION
100 ligne
80 ligne
70 ligne
60 ligne
50 ligne
45 ligne
40 ligne
36 ligne
30 ligne
24 ligne
22 ligne
18 ligne
21/2" —63.5mm
2" —50.8mm
13/4" —44.4mm
11/2" —38.1mm
11/4" —31.7mm
11/8" —28.6mm
1" —25.4mm
7/8" —23mm
3/4" —19.1mm
19/32" —15.1mm
9/16" —13.9mm
3/8" —12mm
SIZES OF BUTTONS Buttons are measured by the English Standard
of 40 Lignes per inch.
1
Rocker arm positioned to permit material and shell
to enter Top Die.Rocker arm disengaged to permit downward movement of material
and shell.MATERIAL BLANK
SCHEMATIC OF DIE PROGRESSION FOR TURNING SHELL AND BACK INTO A COVERED BUTTON USING A SWIVEL MACHINE AND 3-PIECE DIES.
BUTTON COVERING INFORMATIONIn order to produce covered buttons, you will need a steel CUTTER to cut discs of the selected material, a set of DIES (shell and back) for each size button required and a machine to which the dies are attached. A Cutter is supplied with each set of Dies ordered.
The first illustration above 1 shows the material blank in position over the button shell in the bottom Shell Die with rocker arm engaged. By the downward movement of the plunger, the Top Die engages the sleeve of the lower Shell Die and inserts the shell and material into the sleeve of the Top Die 2 . The Top Die is then released and the Back Die, with the pre-selected Back in position, is moved under it automatically
disengaging the rocker arm 3 . The Top Die is then moved downward interlocking the covered Shell with the button Back 4 which produces a complete, secure covered button ready for attachment.
This “Die Action” is virtually the same whether manual or air-powered machines are used. DYNA-LINE offers a complete line of cutting, covering, attaching, and tufting machinery to suit your needs.
A complete button mold consists of a SHELL that gives shape to the button (flat slightly domed or half ball) and a BACK that provides the means for attachment. These include wire eyes; clinch prongs, nails, tacks and hooks used with various types of anchors.
SHELLSWe have the most complete range of shells for every application. The various shapes (wall and crown heights) have been developed over many years. These, coupled with our wide selection of backs can be made into top quality covered buttons regardless of material used. In addition, the shell temper (softness or hardness) is extremely important. Our unique annealing process permits us to consistently produce the full range of shell tempers, for every material requirement.
Aluminum Shells are available in most sizes.
#DSHULD #HIHB Sizes: 30/36 22 to 60
#DSH DHB #DSH-HB 24/45 18/36/40/50 to 100
#DSHXDP 22
2
#DTCLBK (T-Clinch)
#DVCLBK (V-Clinch)
#2800 Lip-Lok (V-Clinch)
WIRE EYE BACKSUsed with tufting twine, our #D9WEBK conventional back performs superbly for most applications. Where an extra strong bond between Shell and Back is desirable it may be best to consider our #2700 Lip Lok Back. Both Use a #9 wire giving you a large opening for ease in threading. The #D7WEBK has a smaller eye opening (#7 = #44) and is intended for use with more delicate materials. For a wire eye with 1/2” opening used with tapes (straps) please see page 7.
#7 Loop—6/32” opening – same as #44#9 Loop—5/16” opening#10 Loop—1/2” opening for Tapes (straps)
Sizes: 18 22 24 30 36 40 45 50 60 70 80 100
HOOK BACKSThese backs are primarily used with Pre-tied twine Loops to assure a uniform tufting depth and to offer faster application. Both types (metal-wire and molded-nylon) have smooth edges that will not fray twine and both are strong and durable. The Nylon backs have a special locking feature designed into the hook.
See page 5 and 10 for Loops & Needles.
Sizes: 22 30 36 45 60
For those who prefer the metal wire backs. #DMETHK Sizes: 30 36
PRONG (clinch) BACKSThis Back type can be used in the same die as many of the other Back types. Tufting with prongs is fast and easy requiring no special skills. Tufting with prongs is secured by simply bending them 90° after insertion.
Various washers can be used to secure them more firmly behind coarse burlap or loose filling material. In certain applications the Round Spring Washer can be used to both lock the prongs and then function as a washer. (Shown at the bottom of page 4)
“T” sizes: 22 24 30“V” sizes: 22 24 30 36 40 45 60Lengths: 11/4”, 11/2”, 2”, 21/2”, 3”
For washer see page 4 A special tool for inserting and bending prongs is available (see page 11)
#D7WEBK
#DNYLHK
#DMETHK
Use with the same shells as metal backs.
Aluminum Shells available for completely Rustproof Button.
#3300 Lip-Lok
#2700 Lip-Lok
#D9WEBK Can also be used with pre-tied loops
3
NO-DENT BACK NAILSThe #DNDHBK and #2900HB are welded to heavy gauge slightly corrugated headboard nails for driving directly into wood. The #DNDTBK and #2900TH are welded to heavy gauge deeply threaded nails to be used with spring washers for a faster, easier alternative to prong tufting.
Sizes: 22 30 36 45 60
Lengths: #DNDHBK and #2900HB: 9/16”, 13/16”, 11/8”, 13/16”#DNDTBK and #2900TH: 1/2”, 5/8”, 3/4”, 7/8”, 1”, 11/2”, 2”
PIVOT BACKS (single)Perfect for attaching covered buttons to upholstered furniture skirts, draperies, bedspreads, slip-covers, etc. No tools are necessary. Just push tacks through the material into the covered Pivot Back and a special spring action locks them together. Tack lengths are determined by thickness of materials plus the button height.
Sizes: 22 24 30 36 40 45 50 60 70 80 100Tack lengths: 3/16” to 1” in 1/16” increments.
TWIN PIVOT BACKSDesigned to be used on pillows, comforters or similar items where a covered button is required on both sides. Twin Pivot Backs consist of a pre-assembled Tack Back which is pushed through one side of the item and a Pivot Back that is pressed on by hand from the opposite side.
Sizes: 22 24 30 36 40 45 60 80 100Tack lengths: 3/16” to 1” in 1/16 increments.
UNASSEMBLED TACKTo be used with your own tack or nail. These sets consist of a collet (back) with a hole to fit your requirements, a paperboard wad to hold the nail securely in the button and a standard shell for the size ordered. Collet is placed in the bottom die, your nail is dropped into the hole, covered with the wad and the shell is then applied normally.
Sizes: 22 24 30 36 40 45 50 60 70 80 100Wads: 60 Pt. (1/16”) and 100 Pt. (1/8”)
Collets available with various size holes to accommodate special requirements—for example see page 7.
#DPIVBK
Driving tool for all button sizes available.
See page 4 for details… be sure to specify correct button size when ordering.
DYNA-LINE
#2900HB
#2900TH#DNDTBK
Threading for use with Spring Washers.
#DNDHBK Corregated Headboard type.
LIP-LOK
#DPVTAC
#DPTKBK Assembled Tack Back.
#DPIVBK
#DSH Shell (See shells page 1)
#DPAPWD Paper Wad
#D128CL Collet
4
UPHOLSTERY NAIL BACKSThese Backs are used for attaching a covered button to a solid backing such as the wood frame or the arm of the upholstered piece. They are pre-assembled with a heavy gauge threaded nail inserted through the collet and covered with a paper wad or steel disc that is held secure by clinching the collet flange. A wide range of tacks and nails are available.
Sizes: 22 24 30 36 40 45 50 60 Lengths: 1/2”, 3/4”, 7/8”, 1”, 11/8”, 11/2”, 2”
BUTTON DRIVING TOOL (Specify correct button size)
The special concave head of this tool conforms to curve of button shell to prevent damage when covered button is driven-in with hammer or similar tool.
WASHERSWashers are used to lock Prong (clinch) backs securely in place. In addition, the poly and paperboard types help to deaden the sound that results from contact between the prongs and spring construction. One of the styles shown here will surely meet your requirements.
Center holes on all these washers—3/16”
SPRING WASHERSSpring washers, when used with threaded Nail Backs, produce a very strong anchor for covered buttons. Both of these washers are manufactured of high quality, tempered spring steel. The larger round one is usually preferred because of its smooth edge. The smaller rectangular washer is perfect in corners or where there are other space limitations.
Can also be used with Prong (clinch) backs— as lock and washer.
#DTHNBKAssembled (14 oz. is standard)
For unassembled collets & wads see page 3.
#SPWSHR-0105/16” x 7/8”
#SPWSHR-01515/16” diameter
#2CLMetal—Beveled, 15/16” diameter
#4Fiber—Flat Squeak proof
3/4” diameter
#5Fiber—Flat Squeak proof
13/8” diameter
#7Paperboard—Flat Squeak proof
2” diameter
#8Poly—Flat Strong, Squeak proof
13/8” diameter
#9Poly—Flat Strong, Squeak proof
Tufting disk 13/8” diameter
5
NYLON pre-tied LOOPS and RAPITIE LOOPS (with anchors)RAPITI LOOPS Rapiti loops with our #7499 steel anchor attached are a complete tufting system. Fast and easy to use, you simply snap the loop onto the button hook, push the anchor through the cushion etc. and release. The spread of the released anchor will hold button firmly in place. Perfect for non-reversible cushions or tight seat backs. Available in lengths from 1 to 8 inches in increments of 1/4 inch.
BT LOOPSBT Loops are pre-measured and pre-tied with a special knot that will never come undone. They come in two strengths, #6 standard or #9 heavy duty. Both are available in lengths from 1 to 8 inches in increments of 1/4 inch.
ANCHORS and ANCHOR BUTTONS
TUFTING TWINEMade from first quality white nylon, these twines are exclusively developed for the maximum strength and abrasion resistance needed in the upholstery construction industry.
Both #554 and BT9 Tufting twines are sold by the 2 Lb. Tube. Only #BT9 Tufting twine is available on 50 Lb. reels with 50 ends. (Enables 50 Lengths of twine to be cut at one time.)
Slip Rapiti anchor into slot of ejector type needle.
Pierce cushion while pressing down on button to hold anchor in slot. Release pressure and withdraw needle. Tufting is complete.
Needles are shown on page 10
1.
2.
#7499Metal
#3220Nylon, white Size: 30 only
#3230Nylon, white Sizes: 30, 45
#3100Nylon Slip-on
#9Poly, Flat 13/8” diameter
50 lb. Reel
2 lb. Tube
STYLE
#554
#BT9
TYPE
Nylon
Nylon Button
YIELD PER LB.
1800 FT.
2200 FT.
BREAKING POINT
80 LBS.
80 LBS.
6
DETACHABLE BUTTONS (Screw-on type)These Screw & Post Twin Button Sets permit easy installation and removal of padding, cushions, bolsters etc. to furniture pieces without destroying the fabric or fastener. Perfect for fastening protective padding to Cane Furniture.
The size 22 #2473/74 set is covered on both sides and is only available in a 7/16” post length.
#D8030S can be supplied with a finished Metal Button on the Screw-on side made from one of our many beautiful shell patterns and in any standard button size. The Post is available in lengths from 5/16” to 1” and in any size Collet and Shell for covering.
FASHION SHAPED BUTTONS (Lip-Lok)These “shaped” buttons offer the designers a dramatic accent to upholstered furniture. The Lip-Lok backs provide a virtually “Pop-Proof” button after covering with your own material.
Sizes: 30 36 45
ONE PIECE MOLDED NYLON BUTTONSMost effective on Casual/Outdoor Furniture or where a weatherproof button is desirable.
All with Hook Backs for use with Pre-tied Loops or Rapities (see page 7)
21 standard colors available (color card upon request.) If you do not see a color to match your requirements please ask us about our custom color-matching program. Each month we continue to expand our one-piece nylon button line with new colors. Please call for samples of the latest colors.
Shell
Paper Wad
Collet
#D8031P
#D889SC
#7475 21/8” x 11/4”
#3200 Smooth High Dome Sizes 22 and 40
#3225 Texture Leather Look Size 40
#3205 Basket Weave, Mid-Dome Size 36
#D8030S
Size 24 Size 30
#2473/74
#DPSTBK
#DSCWBK
Size 22 only
#7476 31/2” x 3/4”
#230 Shell
#3250 Nylon Hook Back
40 22
7
#5000 Series Pre-assembled METAL BUTTONSFor use on upholstered head boards, bar units, booths, etc., these Pre-assembled Buttons are available in all standard sizes, in bright or satin gilt and bright nickel finishes. They can save you time and money when substantial quantities of a particular style and size are required.
TUFTING TAPES (straps) and COLLETSThese Pre-measured Tapes are made of strong, white nylon webbing with solid, white nylon end clips. They are perfect for exactly uniform tufting that is fast and easy— and they provide extraordinary strength. All Tapes are illustrated actual size and are available in lengths from 1 to 8 inches in 1/4 inch increments.
For tufting needle to use with these tapes please see page 10.
SWATCH BOOK GROMMET and WASHERThe flat design of both Grommet and Washer is specifically intended for use with Fabric Samples, Sample Books and Display Racks. Available in Steel (Gilt or Nickel finish) or solid Brass to order.
Hole diameter: .530-.510”Overall diameter: .875”Depth under flange: .135”
BUTTON TAPE COLLETS
#DTAPCL Sizes: 30 36
#DTAPCL Sizes: 45 60
#390/390 TAPE Button Both Ends
#10WBK WIRE EYE BACK
#390/730 TAPE Button One End
#730 LOOP TAPE
#500/500 MATTRESS
TAPE
#5001 Flat Top
#5002 Slight Dome
#5003 Half Ball
WE (WIRE EYE)
NB (NAILBACK)
PV (PIVOT) PB
(PRONG BACK)
We also have Patterned Metal Buttons (over 250 Patterns available)
#E5021
#W5021
Equivalent to #25 Grommet and Washer
8
GROMMETS AND WASHERSFor use on Curtains, Draperies, Covers, Awnings, Tents, Sample Books and Displays; the broad rim of the Grommet and Washer securely anchors any material. Grommets and Washers are made of Brass, either Gilt or Nickel finish. Other metals available on special order.
EYELETSShown here are 3 of the many sizes of eyelets available from miniature electronic board sizes to jumbo tent sizes. We will be pleased to quote and sample to your specifications. All eyelets are available either Brass or Steel with Plated and enameled colors.
Attaching Machinery and Dies are shown on pages 17, 18, and 19.
VENTILATORS and WASHERSUsed as breathers for mattresses, cushions and plastic slip covers. Supplied in Gilt or Nickel finish. Ventilators are made of Solid Brass; Washers are Steel, plated to match Ventilator finish. Brass Washers are available at additional charge.
Note: These Ventilators can be used wherever ventilation is needed. (cabinets, etc.)
#00 #0 #1 #2
#3 #4 #5
#115 /E11
#187 /6280
#206 /6277
TOP VIEW SIDE VIEW
VENT 540 3/4” Wire Mesh
VENT 545 3/4” Perforated
WASHER 54 3/4” Washer
VENT 555 1” Perforated
Washer 55 1” Washer
Size
Hole Diameter
Overall Diam.
Barrel Length
Size
Hole Diameter
Flange Diam.
Barrel Length
00
5/32”
29/64”
3/16”
E11/12
.185”
.312”
.145”
0
1/4”
35/64”
11/64”
1
5/16”
11/16”
7/32”
6280/18
.273”
.450”
.185”
2
3/8”
53/64”
9/32”
3
7/16”
63/64”
21/64”
6277/28
.332”
.593”
.185”
4
1/2”
13/64”
11/32”
5
5/8”
11/4”
13/32”
9
SNAP FASTENERS#7402 is the standard Large Durable. Available in Brass or Steel with a Gilt or Nickel finish. Cap (A) is also available in colors to special order.
In addition to Furniture uses these Screw Studs can be used for automotive and marine applications.
STUD section of snap fasteners comes in three depths:
“C”—Regular Cup “CD”—Deep Cup “LC”—Low Cup
#2701-30—For use with #7402 Stud or Screw Stud above, to provide a covered button with a Large Durable Socket held in place by a collet using standard Shells and Dies.
#2706-30—For use with #7402 Stud (C, LC, CD or SC) This Nylon Socket Collet replaces the need for separate metal sockets and collets.
#D187BD —Special Back Assemblies are available for your particular applications. (Example—Collet & Socket Assembly)
Attaching Machinery and Dies are shown on pages 17, 18, and 19.
TUFTING NEEDLES (ejector type)To be used with Rapities (page 5)
A Cap
B Socket
C Stud
D Post
C
CD
LC
Shell
#7402-B
Collet
Shell
One piece Nylon Socket Collet
#D187BD Sizes: 30 & up
#7402 5/8” Diameter (24 Ligne)
Cap #7402-A
Socket #7402-B
Screw Stud #7402-SC
Available with 3/8” or 5/8” Screw Length.
#2701-30
#2706-30 Sizes: 30 36
Button pushes ejecting pin forward to release clasp.
Handle slides forward to push clasp out of slot.HOLLOW NEEDLE
approximately 10’” LongTip of ejecting pin.
RAPITI LOOPS
NEEDLE-310 SPLIT HANDLE TYPE
NEEDLE-320 RELEASE BUTTON TYPE
10
1/4" Slot holds pre-tied loops Tri-point
Button with prong (clinch) back.HOLLOW NEEDLE Accepts prongs up to 3” long.
SOLID NEEDLE approximately 10” Long.
PUSH THRU TIP
PULL THRU TIP
Ejecting pin Hollow Needle
Finger grip
Spring release
P-30 TUFTING NEEDLES (for pre-tied loops)Used for hand tufting with Pre-tied nylon Loops (page 5)
PRE-TIED LOOP NEEDLE (pull thru type)Also available in 17” length with special order
PRONG (clinch) INSERTING TOOLPrevents prongs from catching in padding or filter material.
REPAIR NEEDLEReplace buttons in upholstered furniture without removing fabric. Additional clasps available in 1000 lots. #350 Needle furnished with 100 clasps and instructions.
NEEDLE-P30 STRAIGHT IN-LINE HANDLE
BT LOOPSNEEDLE-P30-T “T” HANDLE
NEEDLE-330 SOLID STAINLESS STEEL NEEDLE 11” Standard length
NEEDLE-340 Use needle also for bending prongs. 51/2” Standard length also available in 12” length with special order.
NEEDLE-350
#D97550-001-SR REPAIR TUFTING CLASP
11
FT5144 FT5169
UPHOLSTERY NAILS
DECORATOR CAST UPHOLSTERY NAILSThese designs have been selected from our vast array of cast button designs. They provide a stylish and more substantial alternative to regular upholstery nails. Other designs from our button catalogs can also be duplicated.
Sizes: 24 and 30 ligne; with Nail length of ¾".Finishes include: Gilt, Antique Gilt, Antique Nickel, and Oil Rubbed Bronze
SPRING CLIPSThese Spring Clips are stamped of cold-rolled strip steel and are thoroughly tumbled to remove all burrs and unwanted sharp edges. Both styles can be used to securely grip a variety of gauges of Coil-Spring-Borderwire combinations.
Both styles are approximately 11/4” inches x 3/8” inside width.
#902—90 pieces per lb.#932—104 pieces per lb.
To fasten springs to Zig-Zag type back and seat construction. Thoroughly tested for durability and elimination of squeaking.
DYNA-GLIDESDurable Plastic Glides—shown Actual Size
#D12395-902
#D12396-932
EK CLIP-Plastisol lined
Nails shown at actual size
#C2019 Colonial Gold Finish Decorative “Screw-head” Nail. Particularly useful in Waterbed construction
#9HHAMMERED DOME Steel head with Oxford Antique-Gilt Finish
#9STANDARD DOME Steel head with French Natural Old-Gold Finish. Also Nickel and Gilt. Also available 1/2” in Solid Brass.#D99210
1/2” and 5/8” Lengths.Cross section showing construction
DECORATIVE NAILS
PANEL NAIL3/4” Flat Head#8128 Cross section showing construction
#8168/24 #8168/30 #8169/24
#8170/50
FT5148 FT5145 FT5147
12
Part Numbers are in four segments using abbreviations separated by forward slashes (/) usually to indicate: Style No./ Ligne Size or Nail Length/ Material / Finish or other Descriptive information.
Attaching Dies and machines carry a unique part numbering methodology, outlined below.
ATTACHING DIES AND MACHINES
2 piece Die with Short Cutter Part numbers indicate: Die Style Number/Ligne size/Thickness of material/ Die. Part number D36020/22/HU/DIE is Style D36020 used with standard thickness of material. Substitute LU or HUX for thinner or heavier materials, respectively.
Short and Long Cutter only Part numbers indicate: Die Style Number/Ligne Size/ Length of Cutter/Die Type. Part number S36800/42/SH/CUT is Style S36800 in Short version, and is a cutter. Use LG in the third part number segment to designate Long cutters.
3 piece Swivel Die with Long Cutter Part numbers indicate: Die Style Number/Ligne Size/ Swivel designation/Material Thickness. Part number D36220/22/SWI/HU is Style D36220 in 22 ligne size, in Swivel style and uses Medium Thickness materials.
Attaching Machine Part numbers indicate: Equipment Style No./Description/ Additional Description. EQ1920/HND/PRS is Style 1920, Hand Press. Button Driving Tool Part Numbers are in four segments using abbreviations sepa-rated by forward slashes (/) to indicate: Category/Ligne Size/Description/Description. EQTOOL/22/DRT/OOL designates Category Equipment Tool in 22 ligne size and is a Driving Tool.
Cutting Pads and Board Part Numbers are in four segments using abbrevia-tions separated by forward slashes (/) to indicate: Category/Size of Pad/ Use of Pad. EQ-PAD/3X3/CUT/TNG designates Category Equipment Pad, in 3” X 3”size and is a Cutting Pad.
UPHOLSTERY BUTTONS AND SUPPLIES
Shell, Wire Eye and Nylon Back Part numbers Part numbers indicate: Style No./Ligne size/Material /Finish. HIHB/22/SFT/PL is style HIHB in 22 ligne size, made out of Soft grade. Steel with a Plain finish. Other available Material Grades are REG= Regular, HD = Hard Other available Finish is RR= Rust Resistant. HIHB-5/24/REG/RR designates the HIHB Shell in the 5 gross pack, in ligne size 24, made out of Regular Grade Steel in a Rust Resistant Finish. To designate 5 gross pack for other Shell Part Numbers which begin with “D”, replace “D” with “B”. BSH-HB/22/SFT/PLN is the 5 Gross Pack version of the DSH-HB/22/SFT/PLN.
Prong Back, Corrugated Headboard and Annular Threaded Nail Back Part numbers indicate: Style No./Ligne size/Length/Finish. DTCLBK/22/104/RR is style DTCLBK in 22 ligne size, 11/4” length, with a Rust Resistant finish. Prong Back Length Codes : 104=11/4”,108=11/2”, 200 = 2”, 208 = 21/2”, and 300 = 3”. Corrugated Headboard and Annular Threaded Nail Back Length Codes: 008 = 1/2”, 010 =5/8”, 012 = 3/4”, 014 = 7/8”, 100= 1”,104=11/4”,108=11/2”, 200 = 2”, 208 = 21/2”, and 300 = 3’ Standard Package is 25 Gross. To designate 5 gross pack for Part Numbers which begin with “D”, replace “D” with “B”. BTCLBK/22/104/RR designates the DTCLBK in the 5 gross pack. To designate 5 Gross package for the 2800 Lip-Lok insert “- 5” after the style number. 2880-5-/22/200/RR is the 5 Gross Pack version of the 2800-5/22/200/RR.
Single and Twin Pivot Back Part numbers indicate: Style No./Ligne size/ Material /Finish. DPIVBK/24/SSS/RR is style DPIVBK in 24 ligne size, 9/16” length, with Special Spring Steel with a Rust Resistant finish. Tack Part numbers are in only three segments to designate Style No./Length/Finish.
DPVTAC/005/G designates style DPVTAC, 5/16” length, with a Gilt finish. All tacks work with all ligne sizes. Length Codes for Tacks: 003 = 3/16”, 004 = ¼”, 005 = 5/16”, 006 = 3/8”, 007 = 7/16”, 008 = ½”, 009=9/16”. Length Codes for pre-assembled Tacks also include 010 =5/6”, 012 = ¾”, 014 = 7/8”, and 100 = 1”.Standard Package is 25 Gross. To designate 5 gross pack, replace first letter of part number “D” with “B”. BPIVBK/24/SSS/RR designates the DPIVBK in the 5 gross pack.
Collet Back (for use in un-assembled Buttons) Part Numbers to indicate: Style No./Size/Material /Finish. D128CL/22/S/RR designates D128CL, in 22 ligne size, made from Steel, in a Rust Resistant Finish. Paper Wad Part Numbers are in four segments using abbreviations separated by forward slashes (/) to indicate: Style No./Ligne size/Thickness. DPAPWD/22/100/PT designates a DPAPWD Wad, in 22 ligne size, in 100 pt. thickness. Thickness Codes: 60 = 1/16”, 100 = 1/8”. Standard Package is 25 Gross. To designate 5 gross packs, replace first letter of part number “D” with “B”.
Upholstery Nail Back Button Part Numbers indicate: Style No./Ligne size/Nail Length /Finish. DTHNBK/22/100/RR is style DTHNBK in 22 ligne size, 1” nail length, with a Rust Resistant finish. Length Codes for Nails: 008 = 1/2”, 012 = 3/4”, 014 = 7/8”, 100 =1”, 102 = 11/8”, 108 = 11/2”, 200 = 2”. Standard Package is 25 Gross. To designate 5 gross packs, replace first letter of part number “D” with “B”. BTHNBK/22/100/RR designates the DTHNBK/22/100/RR in the 5 gross pack.
Washer Part numbers indicate: Category/Style No./Material/Additional Material. WASHER/8/POL/Y is a Washer in Style 9 made form Polypro-pylene. Standard Package is 25 Gross. To designate 5 gross pack change Category part number segments to WASH-5. Wash-5/POL/Y designates 5 Gross Pack for the WASHER/8/POL/Y.
Spring Washer Part Numbers indicate: Style No./Size/Material /Finish. SPW-SHR/010/HCS/WAX designates Spring Washer size 5/8” in Hard Cold Steel with a wax finish. Other available finish is RR = Rust Resistant.
BT LoopPart numbers indicate: Loop Style /Length/Grade of Twine /Color. BTLOOP/100/BT6/WHT is a BTLOOP which is 1” long, made from Grade 6 (Standard Duty) Twine in White. Also available in BT9, which is Heavy Duty Twine. Rapiti Loop Part Numbers are in four segments using abbrevia-tions separated by forward slashes (/) to indicate: Style No./Size/Material /Finish. RAPITI/100/S/RR designates a Rapiti Loop, 1” in length, with a steel anchor, and rust resistant finish.
Anchors and Anchor Button part numbers to indicate: Style No./Size/ Material /Finish. 7499/40/S/RR designates Style 7499 in ligne 40 with a Steel anchor in a Rust Resistant finish. 32 series part numbers for Anchors are in four segments using abbreviations separated by forward slashes (/) to indicate Style/Size/ Material/ Color. 3230/30/NYL/WHT is Style 3230, in ligne 30, Nylon material in White color. 5 Gross packs are designated by adding a “-5” after Style number.
Twine part numbers indicate: Category/ Style No./Size/Material/. TWINE/554/NYL/ designates Twine in 554 Style, made of Nylon Material. Note : Place “/” at the end of part number as shown.
Detachable Fashion Button and One piece Molded Nylon Button Part Num-bers indicate: Style No./Size/Material /Finish or Color. 230/30/S/PL designates Style 230 in ligne 40 in Steel material in a Plain finish. Other material code is NYL=Nylon, while other Finish Code is RR = Rust Resis-tant. 5 Gross packs are designated by adding a “-5” after Style number.
5000 Series Part Numbers indicate: Style No./Ligne Size/Length /Finish. 5000PB/22/200/PG designates the Style 5000PB in 22 Ligne size, 2” Tack length, with a Polished Gold finish. Substitute alternate Button style
Dynaline Part Number Ordering Guide
13
FASTENING HARDWAREYou will find that Cast Rings are not only superior in strength to regular wire-formed rings, but give your furniture that look and feel of better quality you desire.
For any buckle applications you may have, we can supply literally thousands of styles through our Atlas Buckle Manufacturing Division—complete catalog available.
WIRE “O” and “D” RINGS are available in sizes up to 2 inches I.D
CAST “O” RINGS
DC2015 DC2010 DC2009
DC2005
CAST “D” RINGS
DC2045
DC2052 DC2051 DC2049
#A2538-L-3/4” or 1”#A2538-R-3/4” or 1”
D7695
Sizes: 7/8”, 1”, 11/4”, 11/2”, 13/4”, 2”
1/2” 3/4”
#255723/4” #25586
1/2” Eye
#25617
#25616 Flat Wire
OPEN
CLOSED
HOOK-N-EYE CLOSURE
DC2005/905 Cast Ring with #905 Prong To anchor cushions with snap hooks. Spring Lock Washers shown on page 4.
SNAP HOOKS
(5001, 2, or 3) and/or Back Styles (WE,PT, or PV) in the first product number segment to designate Button style and/or Back style selections. Minimum Order is 10 Gross.
Tufting Tape Part numbers indicate: Category/Length/Termination/Termina-tion. TUFTAP/300/390/390 designates Category Tufting Tape in a 3” Length with a 390 (Termination Style) on both ends. Other termination styles are 390/730, and 500/500. Length Codes are: 100 = 1”, 104 = 11/4”, 108 = 11/2”, 112 = 13/4”, 200 = 2”, 208 = 21/2”, 300 = 3”, 304 = 31/4”, 308 = 31/2”, 400 = 4”, 408 = 41/2”, 500 = 5”, 508 = 51/2”, 600 = 6”, 608 = 61/2”, 700 = 7”, and 800 = 8”.
Collet Back (for use with Tufting Tape) Part Numbers indicate: Style No./Ligne Size/Material /Finish. DTAPCL/30/S/RR designates a DTAPCL Collet in 22 ligne size, made from Steel, in a Rust Resistant Finish. Standard Package is 25 Gross. To designate 5 gross pack, replace first letter of part number “D” with “B”.
Grommet and Washer Part numbers indicate: Category/Size /Material /Finish. GROM/OO/B/G designates Grommet Category in “00” size, made out of Brass with a Gilt finish. To designate 5 Gross package, insert “-5” after the style number. Washer part numbers use the full name WASHER in the Style number segment (Washer/00/B/G) for the 25 Gross packs, and WASH-5 (WASH-5/00/B/G) for the 5 Gross packs.
Vents and Washer Part numbers indicate: Category/Style /Material /Finish. VENT/545/B/G designates Vent Category, in Style 545, made from Brass with a Gold finish.
Upholstery Needle Part numbers indicate: Category/Needle Style No./ Description/. NEEDLE/P30/PSH/ designates Category Needle in Style P30 in Pull or Push Thru type.
1”3/4” 5/8”
1/2”
1/2”
5/8”3/4”
1”
14
Basic Hand Machine MODEL 1920Perfect for Re-upholstery and Sample Workshops.
The ideal machine for limited production quantities. Uses simple to operate 2-piece button covering dies and short cutters; sizes 14 through 100. Frislyen® Poly Cutting Pad and mounting hardware are included.
• Heavy cast iron alloy construction will deliver a lifetime of trouble-free service.
• Produces approximately 90 buttons per hour.• Simple button covering instructions included.
Also adaptable for attaching Ventilators & Washers, Grommets & Washers, Snap Fasteners, etc. by substituting the proper Dies. (See pages 8 & 9 — Dies on page 19)
Specifications: Height: 19”Counter space: 4”X7”Shipping Weight: 15lbs—7kg
MODEL-29 Swivel Hand MachineFor intermediate Button-covering requirements at a minimal cost. Utilizes standard 3-Piece Swivel Dies; same as are used in Foot-powered and Pneumatic-powered equipment.
Faster and more efficient than Model 1920A yet just as durable and easy to operate.
• Produces approximately 200 buttons per hour.• Heavy cast iron alloy will provide a lifetime of trouble-free service
with normal care.• Button-covering instructions are included.
Specifications: Height: 27”Counter space: 4½” X 8½”Net Weight: 17lbs—8kgShipping Weight: 21lbs—9kg
TOP
LEFT RIGHT
DIES SOLD SEPERATELY
Long Cutter (4 inch)
3-Piece Die
2-Piece Die
Short Cutter
Cutting Pad
DIES SOLD SEPERATELY
15
MODEL - 30S Swivel Foot Press• Produces approximately 400 Buttons per hour.
Faster and more efficient than manually operated table-top machines, this Model 30 is recommended when production requirements do not demand the output of fully automatic units. Uses standard 3-piece swivel type button covering dies up to size 80.
Mounted on large, heavy duty stand, with spacious work table for convenient handling of button supplies.
Bench model also available with all mounting hardware.
Specifications:Height: 48”Floor space: 17½ “ X 23”Net Weight: 154lbs — 72kgShipping Weight: 190lbs—85kg
MODEL-84PC Pneumatic CutterPneumatic cutter blanks-out button coverings in quantities for mass production. Magnetic cutter holder block holds one or multiple cutters. Instant cutter replacement for fast size changeover. Two-hand valving for absolute safety. Rugged construction for years of trouble-free service. Standard equipment includes 12x12 inch Frislyen® Poly Cutting Pad, pressure regulator, filter and lubricator.
Specifications: (with stand)Height: 66”Air Pressure: 65/80lbs PSIThroat Space: 5”Floor Space: 17½” x 23”Net Weight: 215lbs—98kgShipping Weight: 235lbs—107kg
Long Cutter (4 inch)
DIES SOLD SEPERATELY
16
MODEL - 37 Cutter & Utility PressA truly heavy duty hand machine that may be used with standard long or short cutters to blank-out multiple layers of fabrics for button covering. The rack and pinion mechanism applies up to 2 tons of pressure with ease. Comes complete with 6x6 inch Frislyen® Poly Cutting Pad and mounting hardware. Can be used up to size 100.
Optional, Magnetic cutter holding block. (holds multiple cutters.)
Specifications: Height: 20”Throat space: 41/2”Net Weight: 56lbs—25kgShipping Weight: 60lbs—27kg
MODEL-84PS Pneumatic Swivel Button-covering machineA modern functional design for a combination of high production, perfect quality and economy. Uses standard 3-piece Swivel Dies; up to size 80, and accommodates Clinch Prongs up to 3 inches long. The sturdy components mean years of trouble-free service, with long-life double-cushion cylinder. Standard equipment includes pressure regulator, filter, and lubricator.
• Produces approximately 500 Buttons per hour.
Specifications: (with stand)Height: 67”Air Pressure: 65/80 PSIFloor Space: 171/2” x 23”Net Weight: 220lbs—10kgShipping Weight: 240lbs—109kg
Long Cutter (4 inch)
DIES SOLD SEPERATELY
17
COVERING & ATTACHING DIESYou can be sure that all Dies and Cutters supplied by or ordered form DYNA-LINE will perform to your complete satisfaction. We use only high-quality steel that is hardened and tempered to exacting specifications. Cutters are perfectly tapered to maximize strength and long life at the sharp cutting edges.
Hand attaching Tools for Ventilators & Washers, Grommets & Washers and Snap Fasteners are also available.)
TOP
LEFT RIGHT
Rotary Die Sets: “Plateau” type for Simplicity Models
Also available: Standard Rotary Dies for other Dial-type machines (Specify Make and Model No. of Machine)
2 piece Button Covering Dies
for use with all single action machines.Short Cutter
(Approx. 11/2 in. long)is supplied with all
2 pc. Dies.
3 piece Button Covering Dies for use in all swivel machines, whether
manual, mechanical or pneumatic.
Long Cutter (Approx. 4 in. long)
is supplied as standard with all 3 pc. Dies.
Cutter for use with Ventilator or Grommet Dies.
(Available either long or short as required.)
Ventilator and Washer Attaching Die. (Specify Make & Model No. of Machine)
Grommet and Washer Attaching Die. (Specify Make & Model No. of Machine)
(A) (D)
(B) (C)
Snap Dies available in sets of A & BCap & Socket only of use with Screw Stud; or in 4 pc. sets to include C & D Stud Post. (Specify Make & Model No. Machine)