s

REF NO: M/TN/q0598/TH/14 DATED: 07.11.14

To,

The Principal,

Fatima Michael College of Engineering & Technology

State Highway 33, Senkottai Village,

Madurai sivagangai Main Road,

Madurai-625 020

KIND ATTENTION: Mr.T.RAJASEENIVASAN

Dear Sir, Sub: Supply of Thermal laboratory equipments reg.

Ref: Your enquiry on 06.11.14

With reference to the above, we are submitting our most competitive offer for the supply

of Thermal laboratory equipments as required by you. We assure the best services after sales.

We expect your early valuable orders to enable us to proceed further.

Thanking you.

Yours faithfully,

For Mech-Lab Equipments,

P.Anand,

09443736743

E.Mail: mechlab.cbe@gmail.com Ph.no : 0422 2929042 sales@mechlabequipments.in Mobile : 09443736743

MECHLAB EQUIPMENTS S.F No: 103/1, Subbanaickenpudur road, Chinnavedampatti (Po), Coimbatore 641 049.

Mfrs & Suppliers of Hydraulic, Thermal, Refrigeration & A/C, Heat Transfer, Dynamics, Steam, Fuels & Automobile Laboratory Equipments to Engineering Colleges, Polytechnics

DISCOUNT NEGOTIABLE

QUOTATION FOR THERMAL LAB

S.No NAME OF THE ITEM PRICE

1. SINGLE CYLINDER FOUR STROKE AIR COOLED PETROL ENGINE TEST RIG ( MAKE : HONDA BRAND NEW )

SPECIFICATIONS

Engine: Single cylinder, 4 stroke air cooled petrol engine of capacity 3 HP at 3000 RPM coupled with loading device on a common base plate.

Panel: Burette with three way cone for fuel consumption, Digital Temperature indicator with selector switch, Digital Speed indicator for speed measurement.

Experiments : 1.Performance test

With Eddy current dynamometer

Rs. 1,73,300/-

2. SINGLE CYLINDER FOUR STROKE DIESEL ENGINE TEST RIG (MAKE : KIRLOSKAR BRAND NEW )

SPECIFICATIONS

Engine: Single Cylinder, 4 Stroke Water Cooled Diesel Engine Of Capacity 5 Hp At 1500 Rpm Coupled With Loading Device On A Common Base Plate.

Panel: Burette for Fuel Consumption, U Tube Manometer for Air Intake Measurement, Digital Temperature Indicator with Selector Switch, Digital Speed Indicator for Speed Measurement.

EXPERIMENTS : 1.Performance Test 2.Heat Balance Test

With Eddy current dynamometer

Rs.1,83,200/-

3. COMPUTERIZED ACQUISITION OF SINGLE CYLINDER 4 STROKE PETROL ENGINE COUPLED TO EDDY CURRENT DYNAMOMETER

SPECIFICATIONS

TECHNICAL DATA:

Make of Engine : Greaves / Honda

Type of Engine : 4 Stroke / Vertical

No of Cylinder : one

Type of Cooling : Air cooled

Rated Power : 3 HP

Rated Speed : 3000 RPM

Loading Arrangements : Eddy Current

dynamometer

CONVENTIONAL MEASUREMENTS:

Fuel Intake : Fuel Tank / Burette / 3- Way Cock

Air Intake : Air Tank / Orifice Plate / Manometer

Temperature : Exhaust Gas Outlet temperature and Ambient.

Speed : using digital tachometer

Load : using analog spring balance

DATA ACQUISITION

Fuel rate measurement using level sensor in turn with 0-5V

Flow sensor for air flow rate measurement in turn with pulse output

Proximity sensor for engine speed measurement in turn with pulse

output

Load cell/load indicator for load measurement with 0-250 V

Temperature measuring using K type thermocouple in turn with 0-5V

Data logger : 8BIT, PIC 16F877A, Crystal 20MHZ, 3 Analog inputs, 4

digital inputs,Rs232 output (9Pin connector)

Hardware and Software for the above readable in LAB VIEW

Software: Customized LABVIEW software for single user.

EXPERIMENTAL CAPABILITIES:

BHP / SFC / Brake Thermal Efficiency, Volumetric Efficiency

SERVICE REQUIREMENT:

5 Amps Power Point

Computer With Printer Of Latest Version

Rs. 4, 39,700/-

4. COMPUTERIZED DATA ACQUISITION OF SINGLE CYLINDER 4 STROKE DIESEL ENGINE COUPLED TO EDDY CURRENT DYNAMOMETER

SPECIFICATIONS

TECHNICAL DATA:

Make of Engine : Kirloskar

Type of Engine : 4 Stroke / Vertical

No of Cylinder : One

Type of Cooling : Water cooled

Rated Power : 5 HP

Rated Speed : 1500 RPM

Loading Arrangement : Electrical dyn

CONVENTIONAL MEASUREMENTS:

Fuel Intake : Fuel Tank / Burette / 3- Way Cock

Air Intake : Air Tank / Orifice Plate / Manometer

Temperature : Exhaust Gas Outlet temperature

And Ambient.

Speed : using digital tachometer

Load : Using digital ammeter and voltmeter

DATA ACQUISITION

Fuel rate measurement using level sensor in turn with 0-5V

Flow sensor for air flow rate measurement in turn with pulse output

Proximity sensor for engine speed measurement in turn with pulse

output

Ammeter and voltmeter for power output measurement with 0-250 V

Speed is controlled by engine governor

Flow sensor for water flow rate measurement in turn with pulse output

Temperature measuring using K type thermocouple in turn with 0-5V

Data logger : 8BIT, PIC 16F877A, Crystal 20MHZ, 3 Analog inputs, 4

digital inputs,Rs232 output (9Pin connector)

Hardware and Software for the above readable in LAB VIEW

Software: Customized LABVIEW software for single user.

EXPERIMENTAL CAPABILITIES:

BHP / TFC / SFC / Brake Thermal Efficiency, Volumetric

Efficiency, Heat balance sheet.

SERVICE REQUIREMENT:

5 amps power point computer with printer of latest version

Rs. 4, 92,800/-

5. STEAM POWER PLANT [1 KW CAPACITY]

SPECIFICATIONS

Steam Turbine ( 1 Kw ) Coupled With Eddy Current Dynamometer,

Separating & Throttling Calorimeter, Steam Condensers & Condensers

Cooling Water Pump Arrangement

Oil Fired Fully Automatic Non-Ibr 300 Kg/Hr Boiler (With Chimney)

Working At 10 Kg/Cm2 Along With Water Softener Combined Steam

Piping With Aluminum Foil Covered Glass wool Insulation

Thermax ( Non-Ibr ) Boiler - Brand new

Rs.11, 63,300/-

SPECIFICATIONS

STEAM LAB PACKAGE [1 KW CAPACITY]

BRIEF DESCRIPTION

The package will contain an IBR boiler, separating and throttling calorimeter, steam turbine

coupled with Eddy Current dynamometer, chimney, and Turbine control panel, condenser (shell & tube

type).

SPECIFICATIONS:

STEAM BOILER :

01. TYPE : 3 Pass, Forced circulation, Coil type, Water tube, Fully automatic,

oil fired.

02. Capacity F & A 100 deg.C : 300kgs/hr

03. Maximum working pressure : 10.54 kg/cm2 (150 psi)

04. Fuel : L.D.O/H.S.D.

05. Fuel consumption : 18 Kgs/hr

06. Electrical Load:

Feed Pump Motor : 0.5 HP

Blower Motor : 0.75

Oil Pump Motor : 0.5 HP

07. Flue gas outlet in mm : 168 mm

STEAM BOILER CONSTRUCTION:

It is designed on forced circulation Heat Exchange principle fabricated out of high

temperature resistant seamless tubes, once through spiral coil nest is arranged to give 3 clear

passes of flue gases forms combustion zone. It ensures for optimum rate of heat release and

maximum heat transfer and low stack temperature. It is ultimately placed in double shell

with Aluminum heat retarded mounted on study steel frame for quick and easy installation.

SHELL AND COIL ASSEMBLY Inner & Outer shell, Aluminum foil in between two shells to act as heat retarder, Nest of once through spiral coil to give 3 clear pass and Top & Bottom refractory block.

BURNER, BLOWER &OIL PUMP ASSEMBLY:

Centrifugal Blower coupled with motor, Vertically downward position placed burner

complete with nozzle, nozzle holder, diffuser plate, ignition electrodes, photocell, sight glass

& solenoid valve. Gear oil pump coupled with motor, Oil filter and pressure gauge.

FEED WATER ASSEMBLY

Positive displacement type piston pump coupled with motor, Pulley, V Belt, Pump safety

valve, Non-return valve & Strainer.

MOUNTINGS, FITTINGS & INSTRUMENTATION:

Main steam stop valve Steam Auxiliary valve Safety valve Blow down valve Steam trap Non return valve Strainer Oil, water & steam pressure gauge with isolating valves Temperature Indicator cum controller Flue gas controller Steam pressure switch Audio Alarm Oil filter Ignition Transformed

ELECTRICAL PANEL

It is mounted on the front side of the boiler at a convenient height, is pre wired and

complete with starters, push buttons indicating lamps all duly labeled, fuses, O/L relays,

contactors and sequence controller.

ACCESSORIES

Air Blower : 0.75 HP

Water Pump (Feed water) : High Head, Triplex pump 0.5 HP

Fuel pump : With filters, Valve 0.5 HP

Pressure control : Through HP/ LP cutout,

Solenoids, pressure switches

FINIS

Red oxide primer and one coat of enamel paint

BASE

Strong Channel Base, Houses all parts of boiler

SOFTENER

Water softener suitable for softening raw water up to 200 PPM of Caco3 complete

with inter connection piping, valves, Filter, Resin, Pressure Gauge, Ejector & brine tank.

CHIMNEY

Flanged ends, 5 m high

STEAM TURBINE

Single Stage, Horizontal shaft, Two nozzle impulse type 1 KW Inlet steam pressure 5 TO 7 bar Speed 3000 RPM Inlet flange 3/4NB flange (one) Outlet flange 3 NB flange (one) Steam control hand operated valve Pressure gauges 0 10 kg/cm (inlet) compound gauge at out let Temperature measurement thermocouples at inlet and outlet Bearing with cooling arrangement

EDDY CURRENT DYNAMOMETER WITH LOADING ARRANGEMENT

Capacity 1KW

Speed 3000 RPM

SPEED MEASUREMENT

Digital Indicator with Proximity sensor (mounted on control panel).

CONTROL PANEL

Switch mains ON/OFF 20 Amps RPM indicator digital, 0 9999 RPM with facility to set up any value, tripping relay

connection between solenoid valve and controller Indicator lamps ( 1 No) Temperature Indicator digital, 0-999 degree centigrade, and thermocouple type

calibrated with six-channel selector switch. Starters 1 Nos. for water circulation pump.

SURFACE CONDENSER

Shell and Tube type Horizontal type One pass of steam in shell One pass of water in tubes Flanged and dished ends with steam gaskets. Vacuum gauge at shell outlet Temperature Measurement: 4 Nos. thermocouples at inlet and outlet of shell and tube. By pass arrangement: Experiments should be conducted either with condenser or

without by using control valves. COOLING WATER PUMP

3.0 HP Centrifugal mono block pump set (TO BE PROVIDED BY THE COLLEGE)

CONDENSATE COLLECTION

20 Lit capacity, fitted with Piezo meter for condensate measurement

COMBINED SEPARATING AND THROTTLING CALORIMETER

Separating and throttling calorimeter is lagged in glass wool, encased in stainless

steel lagging covers. Water gauge glass (10 kg/sq.cm) steam pressure gauge cock and drain with

measuring jar.

Throttling calorimeter is lagged in glass wool, encased in chromium plated lagging

covers. Stainless steel orifice, dial thermometer through a gland direct into steam. Manometer and

connection.

SERVICE REQUIREMENT TO BE PROVIDED BY THE PURCHASER

Electrical Supply : 400/440 V, 3 Phase, 50 Hz.4 wire Electrical Load : 5 HP approx. Fuel Oil : 100 Ltrs approx, for demonstration Sump Tank : 6 ft x 4 ft x 3 ft depth very near to the equipment adjacent to

the outer wall of the laboratory where the equipment is to be installed.

TERMS & CONDITIONS

PRICE : For- College.

TAX : VAT @ 5 % EXTRA.

PAYMENT : 50% Advance along with order, 40% against delivery &

Balance 10 %on demo.

DISCOUNT : NEGOTIABLE

DELIVERY : 04-06 Weeks.

GUARANTEE : 12 Months.

TECHNICAL -

SPECIFICATIONS : We reserve rights to make any changes and also to introduce any developments.

For Mech-Lab Equipments,

P.Anand,

09443736743.