Company Private Company Private

Textron Aviation Safety Initiative January 21, 2017

Company Private

Textron Aviation is the company formed from

Cessna and Beechcraft in March 2014 – together

250,000+ airplanes have been delivered

Cessna 172 Skyhawk Beech Bonanza Cessna 208 Caravan

Cessna O-2 Skymaster

Beechcraft T-6A Texan II Cessna Latitude Hawker 4000

Beechcraft 1900D Cessna O-2 Skymaster

Company Private

Textron Aviation Piston Engine Airplanes

•  205,000+ produced since 1946

•  Of which 190,000 produced before 1987

•  Average age is 43 years old

•  Certified CAR 3

•  Made of Aluminum

•  Single Engine Airplanes flown 100-150 hours annually

Company Private

2015 Piston Engine Usage - Active US Aircraft Total of 141,141 Airplanes Representing All Manufacturers

Over sixty-five percent of active piston engine airplanes are Cessna or Beechcraft

Textron Aviation Piston Engine Airplanes

Company Private

•  Between 2000-2011 Cessna Aircraft developed new structural inspection programs to assure the continued safe operation of piston engine airplanes

•  For single engine airplanes, visual inspection techniques are utilized to detect –  Corrosion –  Cracks caused by metal fatigue

•  New structural inspection programs for Beechcraft airplanes are in work

Textron Aviation Safety Initiative

Company Private

•  Why Inspect?

– Corrosion (rust) and metal fatigue are inevitable

–  Corrosion and metal fatigue reduce the load carrying capability of the airframe –  Like people, airplanes age, and more frequent and intrusive inspections are

required to maintain health (safety)

Textron Aviation Safety Initiative

Company Private

•  Cessna SID Implementation in New Zealand –  Mandatory compliance

–  90 to 95% of inspected airplanes required maintenance action –  20% of those which required action needed major repair –  80% of the findings were corrosion and 20% cracking

–  Most common cracking area is around front and rear door posts –  Another common area of cracking is at lower strut fuselage attachments

Textron Aviation Safety Initiative

Company Private

•  The key to corrosion prevention is to keep the airframe free of moisture

•  A major contributing factor to corrosion is the environment –  Aircraft that operate in coastal environments are more susceptible to metal

corrosion – While water vapor already has a corrosive effect, the water vapor and salt

combination found in coastal environments creates a powerful corrosive agent

–  Aircraft that operate in areas that contain high amounts of industrial particles and fumes in the atmosphere also are more susceptible to corrosion

–  Aircraft that operate in areas where “environmentally friendly” runway deicers are used (i.e., potassium formate, potassium acetate, etc.) are more susceptible to corrosion

Corrosion Prevention

Company Private

Corrosion Severity Map

Company Private

•  There are several common options available to shield the aluminum from electrolytes including:

–  Cladding –  2024 sheet can be coated ("clad") with very thin layers (.001”) of pure

aluminum to protect from corrosion, known as 2024-T3 AlClad –  The sheet material is vulnerable when the cladding is compromised at

edges, drilled rivet holes, or if it is scratched –  Most airframe corrosion occurs at seams and joints, which is why cladding

alone is not sufficient –  Additional steps are necessary to protect seams, holes, and un-clad parts

from exposure to electrolytes

Corrosion Prevention

Company Private

•  There are several common options available to shield the aluminum from electrolytes including:

– Chemical Treatments – Alodine or other chemical treatments are used to enhance the corrosion

resistance of the pure aluminum cladding

Corrosion Prevention

Company Private

•  There are several common options available to shield the aluminum from electrolytes including:

–  Sealants –  Paint is the most commonly used sealant for corrosion protection and is the

best defense against airframe corrosion –  Modern polyurethane aircraft paints create a thick, impenetrable barrier

that effectively keeps moisture away from the metal, and lasts a long time - - 10 years or more

–  Paint only protects the exterior of the airframe –  Cessna airframe interiors of most pre-1986 airframes were not

painted (primed) –  Many Beech airframe interiors were only partially painted (primed)

Corrosion Prevention

Company Private

•  There are several common options available to shield the aluminum from electrolytes including:

–  Corrosion Preventative Compounds (CPCs) –  Effective means for protecting those parts of an airframe that were not

originally protected from corrosion –  Guidelines for application and use of CPCs are provided in the revised

Service Manual – CPCs must be reapplied periodically

–  The following CPCs are recommended for use on Textron Aviation airplanes

Dry film compounds: ARDROX AV-8* and AV-15 Cor-Ban 23* and Cor-Ban 35

Non-dry grease: Cor-Ban 27L

Non-dry oil: Corrosion X

* Preferred where high penetration of corrosion inhibiting compound is required.

Corrosion Prevention

Company Private

•  As airplanes continue to age, these numbers are likely to increase

•  Corrosion is responsible for approximately: –  7% of the airworthiness directives 1

–  20% of service difficulty reports (SDRs)

•  Corrosion can be deadly –  Corrosion contributed to 91 accidents/incidents in the United States between

1983 and 1994 2

– These and other accidents have resulted in hundreds of fatalities 3

1  Swift, S., “Rusty Diamond”, 24th ICAF Symposium, May 2007.

2  Hoeppner D,, Chandrasekaran V., Taylor A., “Review of Pitting Corrosion Fatigue Models”, 20th ICAF Symposium, 1999.

3  Aviation Safety Network Database, http://aviation-safety.net/index.php

Corrosion Results

Company Private

•  Corrosion and metal fatigue both reduce the load carrying capability of the airframe

•  Corrosion and fatigue are not entirely independent processes - corrosion affects the expected fatigue life of airframe parts

–  Corrosion pitting creates a stress concentration which leads to crack initiation and potentially faster crack

–  Corrosion reduces the thickness of a part and therefore increases the stress in the part

View of Spar Cap Fracture Surface View of Spar Cap Lower Surface

Corrosion and Metal Fatigue

Company Private

•  Beech 18 Wing Front Spar

•  Beech Bonanza/Baron Control Surfaces

•  Beech Bonanza/Baron Front Spar Leading Edge Lower Hinge-Pin Attachment

•  Cessna 177 Wing Spar

•  Cessna 200 Series Wing Spar

•  Cessna 182 Lower Strut Fitting

•  Cessna Single Engine Wing Spar

•  Cessna Single Engine Rudder Pedal

•  Cessna Single Engine Main Landing Gear

Corrosion Examples

Company Private

Beech Bonanza/Baron Control Surfaces

Company Private

Special Airworthiness Information Bulletin (SAIB) CE-15-22

Beech Bonanza/Baron Front Spar Leading Edge Lower Hinge-Pin Attachment

Company Private

177RG

177B Found as a result of SEB-57-03

Special Airworthiness Information Bulletin (SAIB) CE-16-16

Cessna 177 Wing Spar

Company Private

Found as a result of SID Inspection 57-11-01

Cessna 200 Series Wing Spar

Company Private

Found as a result of SID Inspection SID 57-40-01

Cessna 182 Lower Strut Fitting

Company Private

Wing Spar Corrosion

Found as a result of CPCP Inspection

Company Private

Cessna Single Engine Rudder Pedal

Fractured Pedal Arm Tube

SID 27-20-01

Company Private

Cessna Single Engine Main Landing Gear

•  Made from 6150M High- Strength Steel

•  A pit as small as .005” can initiate a fatigue crack which will result in fracture of the gear

•  Keep surface painted with polyurethane paint and blend out pits per Service Manual

Rust

Model 182 Flat Spring Gear SID 32-13-01

Company Private

.017” Pit

Cessna Single Engine Main Landing Gear

Company Private

– Over 700 people have died in fatigue related accidents since 1980

Metal Fatigue

•  Aviation has had to address metal fatigue in the design and inspection of airframes since 1954

•  Fatigue can be deadly – Metal fatigue contributed to 2240 deaths in 1885 airplane accidents between

1927 and 1980 1

– The five most common fatigue crack initiation sources in these accidents were: (1) bolt, stud or screw; (2) fastener or other hole, (3) fillet, radius or sharp notch; (4) welds and (5) corrosion

1  Campbell and Lahey 1984, ‘A Survey of Serious Aircraft Accidents Involving Fatigue Fracture’, International Journal of Fatigue, January 1984

2  ‘Investigation into Ansett Australia Maintenance Safety Deficiencies and the Control of Continuing Airworthiness of Class A Aircraft’, Appendix 8 from the Australian Transport Safety Bureau’s web site, www.atsb.gov.au.

2

Company Private

Fatigue Under Microscope Typical Fatigue Failure

What is Metal Fatigue?

Company Private

Aloha Airlines 1988

Dan Air 1977

F111 1969

Beech T-34 1999-2004

Cessna 172 Certified 1955

Cessna 206 Certified 1963

Hig

h-P

rofil

e A

ccid

ents

Te

xtro

n Av

iatio

n C

AR

/FA

A P

art 2

3 R

egs

& P

olic

ies

Fuselage Fatigue Evaluation 1965

Wing Fatigue Evaluation 1969

Instructions for Continued

Airworthiness 1980

Empennage Fatigue

Evaluation 1989

AC91-82 Fatigue Management Program 2008

Comet 1954

1940 1950 1960 1970 1980 1990 2000 CAR FAA

Beech 23 Certified 1962

FAA Regulations Through the Years

Beech 35 Certified 1947

Company Private

Key Lessons Learned From High Profile Accidents

•  Comet – Fatigue must be considered in design, not just static strength

2,703 & 3,680 total hours

•  F111 - Manufacturing or accidental damage must be considered

105 total hours

Company Private

•  Boeing 707-321C - Fail-safe alone doesn’t work, need inspections

Key Lessons Learned From High Profile Accidents

47,621 total hours

Company Private

•  Boeing 737 - Inspection programs do not keep airplanes safe indefinitely. Eventually there needs to be a terminating action of modification or retirement.

Key Lessons Learned From High Profile Accidents

35,496 total hours

Company Private

•  Beech T-34 – Detailed inspection programs are needed for the entire airframe, not just for known areas of cracking

Key Lessons Learned From High Profile Accidents

3200, 8257 & 9316 total hours

Company Private

•  Model 402C designed in 1979 •  Twin-Engine unpressurized airplane •  Seats up to 9 passengers •  Often used for cargo hauling or scheduled airline passenger service

Case Study – Cessna 402C

Company Private

•  Wing spar cracking discovered in 1999 led to addition of wing spar strap (SID 57-10-16)

•  Engine beam cracking discovered in 2015 led to life limit of engine beams (SID 54-10-01)

•  Nacelle fitting (engine beam to wing attachment) cracking discovered in 2016 led to life limit of nacelle fittings

•  Carry-thru forward spar cracked in 2017 (SID 57-10-14)

Case Study – Cessna 402C

Company Private

•  Model 210 with cantilevered wing designed in 1967 •  Single-Engine unpressurized high performance airplane •  Seats up to 6 passengers •  Used for a variety of missions including cargo hauling, geophysical

survey, sight seeing as well as private usage

Case Study – Cessna 210

Company Private

•  Eight reports of wing spar cracking reported in 2012 (SID 57-11-03)

•  Horizontal stabilizer aft attachment fitting cracking discovered in 2011

•  Horizontal stabilizer forward spar cracking discovered in 2011 (SID 55-10-01)

Case Study – Cessna 210

Company Private

•  Beech Bonanza/Baron Rudder Brake Pedal Pivot Hole

•  Beech Bonanza/Baron Flight Control Cables

•  Cessna 180/185 Tailcone Stringer

•  Cessna 172 (Restart) FS 108 Bulkhead

•  Cessna 172/182/206/210 Forward Doorpost at Strut Attachment

•  Cessna 150/152 Vertical Stabilizer Attach

•  Cessna 177 Lower Wing Spar

Metal Fatigue Examples

Company Private

Fractured Rudder Brake Pedal Pivot Hole

Beech Bonanza/Baron Rudder Brake Pedal Pivot Hole

Company Private

Beech V35A Aileron Control Cable

CASA AD/GENERAL/87 - primary flight control cable assemblies using terminals constructed of SAE-AISI 303 Se or SAE-AISI 304 stainless steel must be replaced after 15 years

Beech Bonanza/Baron Flight Control Cables

Company Private

Special Airworthiness Information Bulletin (SAIB) CE-16-16 SID 53-10-01 AD under consideration

Cessna 180/185 Tailcone Stringer

Company Private

Found as a result of SID Inspection SID 53-12-03

Cessna 172 (Restart) FS 108 Bulkhead

Company Private

Crack AD or SAIB under FAA consideration SID 53-12-01

Cessna 172/182/206/207/210 Forward Doorpost at Strut Attachment

Company Private

Crack Special Airworthiness Information Bulletin (SAIB) CE-16-03 SID 55-11-02

Cessna 150/152 Vertical Stabilizer Attach

Company Private

Special Airworthiness Information Bulletin (SAIB) CE-16-16 SID 57-11-03

Cessna 177 Lower Wing Spar

Company Private

•  Inspections –  Based on field history –  Reviewed by customer focus group

•  Inspection Details –  Corrosion prevention and control program –  Directed visual inspection for corrosion –  ~15-20 visual inspections to look for cracks –  Boroscope and magnifying glass required to complete inspections

•  SID inspections are designed to be accomplished at an annual when airplane is opened up

•  Anticipated cost is dependent on flight hours and overall airplane condition –  Approximately 10 hours for low time airplane maintained per service manual –  Approximately 25 hours for high time airplane maintained per service manual –  Any required repairs are additional cost

SID Inspections

Company Private

•  Safety is a partnership between owners (maintainers), manufacturers and the FAA

•  Comply with airworthiness directives

•  Report anomalies

•  Send Pictures!!

Summary