Textiles and Garments 紡織品及成衣 - ITC

HOKLAS 003 List of CAB Terminated ActivitiesList of activities for which accreditation has been terminated
(Notification Letter No. HOKLAS003-263; Effective date of termination: 18 November 2021)
The Hong Kong Standards and Testing Centre Ltd.
10, Dai Wang Street, Taipo Industrial Estate, Tai Po, New Territories, Hong Kong
10
Toxicological tests
Food containers (polyamide kitchenware) Migration of primary aromatic amine Commission Regulation (EU) No. 284/2011
(time-temperature exposure conditions of of 22 March 2011, Article 3, cl. 3(a)
2 hours at 70 C and 2 hours at 100 C) Test procedures for compliance testing:
European Commission Joint Research Centre
Technical Guidelines on Testing the Migration
of Primary Aromatic Amines from Polyamide
Kitchenware and of Formaldehyde from
Melamine Kitchenware, EUR 24815 EN 2011,
Section 7; and
In-house method CFD/STP/CHM/145
Annex III
List of tests for which accreditation has been terminated (Notification Letter No. HOKLAS003-262; Effective date of termination: 9 September 2021)
Annex III, NL No. HOKLAS003-262 Page 1 of 10
10, Dai Wang Street, Taipo Industrial Estate, Tai Po, New Territories, Hong Kong 10
Textiles and Garments
SPECIFIC TEST OR PROPERTY MEASURED
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED

Flammability tests :-
Specific Products :-
ISO 10966: 2011 Cl. 4.12
- Bedding items, which can normally be placed - Ignitability by smouldering cigarette BS EN ISO 12952-1: 1999
on a mattress EN ISO 12952-1: 1998
ISO 12952-1: 1998
EN ISO 12952-2: 1998
for the above six standards
Dry clean method (ISO 3175)
- Bedding items, which can normally be placed - Ignitability by small open flame BS EN ISO 12952-3: 1999
on a mattress EN ISO 12952-3: 1998
ISO 12952-3: 1998
EN ISO 12952-4: 1998
for the above six standards
Dry clean method (ISO 3175)
- Curtains and drapes - Vertical test BS EN ISO 15025: 2002, surface and bottom ignition
NFPA 701: 2010 Test Method 1
< Excluding the following>
Cl. 16.3.1(1)
Annex III

Flammability tests :- (cont’d)
Specific Products :- (cont’d)
- Protective clothing against limited spread - Vertical test BS EN ISO 14116: 2008 Cl. 6.1
flammability BS EN ISO 14116: 2015 Cl. 6.1
- Protective clothing for use in welding and - Vertical test BS EN ISO 11611: 2007 Cl. 6.7
allied processes BS EN ISO 11611: 2015 Cl. 6.7
- Protective clothing to protect against heat - Vertical test BS EN ISO 11612: 2008 Cl. 6.3
and flame BS EN ISO 11612: 2015 Cl. 6.3
- Upholstered parts of wheelchairs - Resistance to ignition BS ISO 7176-16: 1997
ISO 7176-16: 1997
Annex III
Unit B, 10/F, Block 1, Tai Ping Industrial Centre, 57 Ting Kok Road, Tai Po, New Territories, Hong Kong
57 10 B
Physical and Mechanical Testing
ITEM TESTED OR MEASURED

Polymer and Polymer
- Construction
- Resistance to damage by toppling
and resistance to leakage after toppling
- Colour
- Marking
Annex III
Unit B, 10/F, Block 1, Tai Ping Industrial Centre, 57 Ting Kok Road, Tai Po, New Territories, Hong Kong 57 10 B

Care performance tests :-
General textiles and garments - Dimensional stability to washing (textiles) ISO 5077: 1984
- Dimensional stability to washing (garments) AATCC Test Method 150-2010
- Domestic washing and drying procedures BS EN ISO 6330: 2001 + A1: 2009
ISO 6330: 2000 + A1: 2009
<Excluding the following>
Cl. 8.4
- Preparation, marking and measuring for BS EN ISO 3759: 2008
dimensional change tests ISO 3759: 2007
ISO 3759: 1994 with Corr. 2
- Wool textiles products - Relaxation & felting shrinkage WOOLMARK TWC-TM 31-2009
Specific products
- High visibility clothing - Dimensional stability to washing BS EN ISO 20471: 2013 Cl. 5.4
(Exclude press dry) BS EN ISO 20471: 2013 +A1: 2016 Cl. 5.4
- Protective clothing for use in welding and BS EN ISO 11611: 2007 Cl. 6.5
allied processes
- Protective clothing to protect against heat EN ISO 11611:2015 Cl. 6.6
and flame
Annex III

Colour fastness tests :-
General textiles and garments - Dry cleaning AATCC Test Method 132-2009
BS EN ISO 105 D01: 1995
ISO 105 D01: 1993
- Perspiration AATCC Test Method 15-2002
BS EN ISO 105 E04: 2009
ISO 105 E04: 2008
ISO 105 X12: 2001
ISO 105 X12: 1993
- Domestic and commercial laundering BS EN ISO 105 C06: 1997
ISO 105 C06: 1994 with Corr. 2
(using a non-phosphate reference ISO 105 C08: 2010
detergent incorporating a low temperature BS EN ISO 105 C08: 2002
bleach activator) ISO 105 C08: 2001 with Corr. 1
(oxidative bleach response using a ISO 105 C09: 2001 with Amendment No. 1
non-phosphate reference detergent
activator)
- Washing with soap or soap and soda BS EN ISO 105 C10: 2007
ISO 105 C10: 2006
SASO 170: 2005
- Wool and wool blend textiles materials - Hand washing WOOLMARK TWC-TM 250-2009
- Machine washing WOOLMARK TWC-TM 193-2009
Annex III

Colourfastness tests :- (cont’d)
BS EN ISO 105 E01: 2010
ISO 105 E01: 2010
SATRA TM 167: 2001
Specific products:-
- High visibility clothing - Perspiration BS EN ISO 20471: 2013 +A1: 2016 Cl. 5.3.2
BS EN ISO 20471: 2013 Cl. 5.3.2
- Rubbing/Crocking BS EN ISO 20471: 2013 +A1: 2016 Cl. 5.3.1
BS EN ISO 20471: 2013 Cl. 5.3.1
- Footwear
- Footwear materials
- uppers and linings (leather) - Rubbing (crockmeter test) SATRA TM 167: 2017
SATRA TM 167: 2001
SATRA TM 335: 1994
Colour measurement tests :-
General textiles and garments - Calculation of small colour differences AATCC Test Method 173-2015
AATCC Test Method 173-2009
- Instrumental assessment of the change in AATCC Evaluation Procedure 7: 2015
colour AATCC Evaluation Procedure 7: 2009
- Whiteness of textile AATCC Test Method 110-2015
Annex III

Construction tests :-
General textiles and garments - Mass per unit area (weight) ASTM D3776-09 (Reapproved 2013)
ASTM D3776-09
ASTM D 3775-08
Other materials :-
BS EN ISO 2589: 2002 with Cor. 1
EN ISO 2589: 2002
- Children’s upper outwear - Measurement of drawstrings ASTM F1816-97 (Reapproved 2009)
- Footwear
- Footwear materials - Thickness of leather and insole materials SATRA TM 1: 2004
- Uppers and linings (textiles and coated - Thickness of non-leather flexible sheet materials SATRA TM 27: 2004
textiles)
Annex III

Fibre analysis :-
(animal fibres, yarn and fabric only) ASTM D2130-90 (Reapproved 2008)
- Wool ISO 137: 2015
Performance tests :-
General textiles and garments - Abrasion resistance BS EN ISO 12947-2: 1999
(determination of a specimen breakdown - ISO 12947-2: 1998 with Corr. 1
Martindale tester)
ISO 4892-2: 2006 + A1: 2009
- Weathering resistance to UV AATCC Test Method 186-2009
ASTM D4329-05
Annex III

Strength tests :-
General textiles and garments - Tearing strength (falling pendulum) ASTM D1424-09
- Tensile strength (strip test) BS EN ISO 13934 Part 1: 1999
ISO 13934 Part 1: 1999
- Tensile strength (grab test) BS EN ISO 13934-2: 1999
ISO 13934-2: 1999
- Footwear
- Shoe bottoms - Peel strength of footwear sole bonds SATRA TM 411: 1992
- Upper sole adhesion BS EN ISO 17708: 2003
EN ISO 17708: 2003
ISO 17708: 2003
- High visibility clothing - Tensile strength (strip test) BS EN ISO 20471: 2013 Cl. 5.5.1
BS EN ISO 20471: 2013 + A1: 2016 Cl. 5.5.1
- Protective clothing against limited spread - Tensile strength (strip test) BS EN ISO 14116: 2008 Cl. 6.2.1
flammability . BS EN ISO 14116: 2015 Cl. 6.2.1
- Protective clothing for use in welding and allied - Tensile strength (strip test) BS EN ISO 11611: 2007 Cl. 6.1 (textile materials)
processes BS EN ISO 11611: 2015 Cl. 6.2 (textile materials)
- Soft infants carriers - Loading tests ASTM F 2236-16a Cl. 6
ASTM F 2236-14 Cl. 6
ASTM F 2236-10 Cl. 6
Annex III
57 10 B
Toys and Children’s Products

Safety and performance tests :-
Soft infant and toddler carrier Safety requirements and test methods 16 CFR Part 1226
in conjunction with ASTM F2236-14
ASTM F2236-14
Annex III
(Notification Letter No. HOKLAS003-261; Effective date of termination: 22 April 2021)

Notification Letter no. HOKLAS003-261, Annex III Page 1 of 2
10
Safety tests :-
Electrical accessories
- Rewirable and non-rewirable13 A fused - General tests, inspection, measurement, BS 1363: Part 1: 1995 with Amd. 9541,
plugs gauging, manipulation and materials Amd. 14539, Amd. 17435 and + A4: 2012
- Rewirable 13 A switched and unswitched - General tests, inspection, measurement, BS 1363: Part 2: 1995 with Amd. 9542,
socket-outlets gauging, manipulation and materials Amd. 15438, Amd. 17436 and + A4: 2012
- Rewirable adaptors - General tests, inspection, measurement, BS 1363: Part 3: 1995 with Amd. 9543,
gauging, manipulation and materials Amd. 14540, Amd. 17437, Corr. 14225 and
+ A4: 2012
Annex III
(Notification Letter No. HOKLAS003-261; Effective date of termination: 17 August 2021)

10
Safety tests :-
:-
Luminaire:
:
- General requirements for luminaire with - Compliance inspection and safety test GB 7000.1-2007
rated power up to 500W <Excluding the following>
Cl. 4.4.5, 4.11.6, 4.24,
10.2.2 (tests for luminaire with ignitor)
(Note: The above standard should be used in
conjunction with the product test standards as
detailed in relevant Part 2 of GB 7000)
- , 500W - GB 7000.1-2007
<>
(Notification Letter No. HOKLAS003-261; Effective date of termination: 22 April 2021)

10
Safety tests :-
Electrical accessories
- Rewirable and non-rewirable13 A fused - General tests, inspection, measurement, BS 1363: Part 1: 1995 with Amd. 9541,
plugs gauging, manipulation and materials Amd. 14539, Amd. 17435 and + A4: 2012
- Rewirable 13 A switched and unswitched - General tests, inspection, measurement, BS 1363: Part 2: 1995 with Amd. 9542,
socket-outlets gauging, manipulation and materials Amd. 15438, Amd. 17436 and + A4: 2012
- Rewirable adaptors - General tests, inspection, measurement, BS 1363: Part 3: 1995 with Amd. 9543,
gauging, manipulation and materials Amd. 14540, Amd. 17437, Corr. 14225 and
+ A4: 2012
Annex III

10
Safety tests :-
:-
Luminaire:
:
- General requirements for luminaire with - Compliance inspection and safety test GB 7000.1-2007
rated power up to 500W <Excluding the following>
Cl. 4.4.5, 4.11.6, 4.24,
10.2.2 (tests for luminaire with ignitor)
(Note: The above standard should be used in
conjunction with the product test standards as
detailed in relevant Part 2 of GB 7000)
- , 500W - GB 7000.1-2007
<>
57 10 B
Construction Materials
Bathroom and kitchen sets
- Showers for bathing Performance tests :- AS/NZS 3662: 2005 + A1: 2006 + A2: 2009
< Excluding the following > - High pressure flow rate + A3: 2010
- shower hoses - Low pressure or unequal pressure flow rate <Excluding the following>
- Mean spray spread angle Cl. 5.4
- Temperature drop
- Marking
- Showers for bathing Performance tests :- Water Supplies Department - The Hong Kong
- Nominal flow rate Voluntary Water Efficiency Labelling Scheme
- Mean spray spread angle on Showers for Bathing (Dec 2011) Annex1
- Temperature drop Section I & Section II
- Flow controller endurance
Tile Grout Linear shrinkage of latex-portland cement grout ANSI A118.6: 1992
Cl. H-4.3
Cl. H-3.4
Annex II
(Notification Letter No. HOKLAS003-257; Effective date of termination: 17 June 2021)

10
Tests for genetically modified organisms
(GMO): -
Soy and soy derived foodstuff Qualitative screening of transgenic traits:- ISO 21571:2005
(except liquid, oil) (Partial sequence of) (Nucleic acid extraction)
- Soy lectin gene (le 1) ISO 21569:2005+A1:2013
- Cauliflower mosaic virus promoter (CaMV35S) (Polymerase chain reaction with gel image analysis)
- Terminator of nopaline synthase gene from
- Agrobacterium tumefaciens (NOS)
from Cauliflower mosaic virus and the chloroplast (Real-time polymerase chain reaction)
targeting signal of Petunia hybrida preceding the
sequence of Agrobacterium 5-
(epsps)
- The junction between the chloroplast transit JRC Compendium of Reference Methods for GMO
peptide (CTP) sequence from Petunia hybrida Analysis (QT-CON-00-001)
epsps gene and the CP4 from epsps gene from (Real-time polymerase chain reaction)
Agrobacterium tumefasciens
Corn and corn derived foodstuff Qualitative screening of transgenic traits:- ISO 21571:2005
(except liquid, oil) (Partial sequence of) (Nucleic acid extraction)
- Maize invertase gene (IVR1) ISO 21569:2005+A1:2013
- Cauliflower mosaic virus promoter (CaMV35S) (Polymerase chain reaction with gel image analysis)
- Terminator of nopaline synthase gene from
- Agrobacterium tumefaciens (NOS)
derived from Bacillus thuringiensis and the intron (Real-time polymerase chain reaction)
sequence of maize alcohol dehydrogenase gene
(adh1) (Bt-11)
from Cauliflower mosaic virus and modified (Real-time polymerase chain reaction)
phosphinothricin acetyltransferase gene (pat) from
Streptomyces viridochromogenes (Bt-11)
Notification Letter no. HOKLAS003-257, Annex II Page 1 of 1
Annex III
(Notification Letter No.: HOKLAS003-251; Effective Date of termination: 8 May 2020)

10
Environmental Testing
Water and Wastewater Microbial indicators :-
- Coliform/E. coli APHA 20e 9221
(By most probable number (MPN) method)
- Fecal Coliform APHA 20e 9221
(By most probable number (MPN) method)

10
General foodstuff Microbiological tests :-
(BAM online), Ch. 4, September 2002
(MPN Method)
(MPN Method)
(BAM online), Ch. 4, September 2002
(MPN Method followed by MUG Method) or
(MPN Method followed by completed test for E. coli)
US FDA Bacteriological Analytical Manual Online
(BAM online), Ch. 4, February 2013
(MPN Method followed by MUG method) or
(MPN Method followed by completed test for E. coli)
Mooncake Microbiological tests :- GB 19855-2005 Cl. 5.4 and
GB 7099-2003 Cl. 4.4
2 ()
- Aerobic Plate count GB 4789.2-2010
- Coliform count GB 4789.3-2010 (MPN )
- Molds counts GB 4789.15-2010
- Salmonella GB 4789.4-2010

10
Chemical tests :-
Toys - paint and similar surface-coating materials - Total lead content ASTM F963-11, Cl. 4.3.5.1 (1)
ASTM F963-16, Cl. 4.3.5.1 (1)
[Test procedures for compliance testing:-
CPSC Test method: CPSC-CH-E1003-09.1
and Other Similar Surface Coating, February 25, 2011]
- Migration of the elements ASTM F963-11, Cl. 4.3.5.1 (2)
Antimony, Arsenic, Barium, Cadmium, ASTM F963-16, Cl. 4.3.5.1 (2)
Chromium, Lead, Mercury, Selenium Test procedures for compliance testing:-
Cl. 8.3.2 – 8.3.4
Toys - substrate materials - Total lead content ASTM F963-11, Cl. 4.3.5.2 (2)(a)
(excluding children’s jewelry; excluding ceramic, ASTM F963-16, Cl. 4.3.5.2 (2)(a)
glass, crystal and other siliceous materials) [Test procedures for compliance testing:
Total Lead (Pb) in Non-metal Children’s Product,
November 15, 2012
Total Lead in Children’s Metal Products,
(Including Children’s Metal Jewelry),
November 15, 2012
XRF spectrometry]
Toys - substrate materials - Migration of the elements ASTM F963-11, Cl. 4.3.5.2 (2)(b)
(excluding children’s jewelry) Antimony, Arsenic, Barium, Cadmium, ASTM F963-16, Cl. 4.3.5.2 (2)(b)
Chromium, Lead, Mercury, Selenium Test procedures for compliance testing:
Cl. 8.3.5

10
Chemical tests :- (cont’d)
[Test procedures for compliance testing:
CPSC Test Method: CPSC-CH-E1004-11
Cadmium (Cd) Extractability from Children’s
Metal Jewelry, February 03, 2011]
Total cadmium content screening ASTM F963-11, Cl. 4.3.5.2 (2)(c) and 8.3.1
Test procedures for compliance testing:
In-house method TCD/TPM/CHM/079 (AAS)
In-house method TCD/TPM/CHM/115 (AAS)

10
Toys and other articles intended for use by [for US Public Law 110 -314
children Consumer Product Safety Improvement Act 2008
- plastic, polymer and other non-siliceous - Total lead content Test procedures for compliance testing:-]
materials CPSC Test method: CPSC-CH-E1002-08.1
Standard Operating Procedure for Determining Total Lead
(Pb) in Non-metal Children’s Product, June 21, 2010
- metal - Total lead content Test procedures for compliance testing:-
Children’s Metal Products, June 21, 2010
Toys - Total lead [for Canada Consumer Products Safety Act
Children’s Jewellery Regulations, SOR/2011-19
Test procedures for compliance testing:]
Lead in Metal Children’s Products, June 21, 2010
- Total lead Canada Consumer Products Containing Lead
(Contact with Month) Regulations, SOR/2010-273
Product Safety Laboratory Book 5 – Laboratory
Policies and Procedures Part B: Test Methods
Section, Method C02.3 Determination of Total
Lead in Polyvinyl Chloride by Close Vessel
Microwave Digestion

10
SOR/2005-109
- Total lead Product Safety Bureau Reference Manual Book 5 -
Laboratory Policies and Procedures Part B: Test
Method Section, Method C02.2 Determination of
Total Lead in Paint and Applied Coatings
- Total mercury In-house methods TCD/TPM/CHM/045
(by microwave digestion) and
Test procedures for compliance testing:]
- Total lead Product Safety Bureau Reference Manual Book 5 -
Laboratory Policies and Procedures Part B: Test
Method Section, Method C02.2 Determination of
Total Lead in Paint and Applied Coatings
Toys and Other Consumer Products
Toys - Total lead Canada Toys Regulations, SOR/2011-17,
Section 27(3)(c)
Product Safety Laboratory Book 5 - Laboratory
Policies and Procedures Part B: Test Methods
Section, Method C02.3 Determination of Total
Lead in Polyvinyl Chloride by Close Vessel
Microwave Digestion

10
Finger paints - Migration of the elements EN 71-7: 2002 Cl. 4.4 and 5.4
Antimony, Arsenic, Barium, Cadmium, AS/NZS ISO 8124.7: 2003 Cl. 4.4 and 5.4
Chromium, Lead, Mercury, Selenium
PVC, PVA and surface coating in toys and Diisobutyl phthalate (DIBP) In-house methods TCD/TPM/CHM/085
children’s products Di-n-hexyl phthalate (DNHP) (by GC-MSD)
Di-n-pentyl phthalate (DPENP)
Dicyclohexyl phthalate (DCHP)
All toys - Butyl benzyl phthalate (BBP) [for GB 6675.1-2014 Cl. 5.3.7
- Dibutyl phthalate (DBP) Test procedures for compliance testing:-]
- Bis (2-ethylhexyl) phthalate (DEHP) CPSC Test method: CPSC-CH-E1001-09.3 Standard
- Di-n-octyl phthalate (DNOP) Operating Procedure for Determining Phthalate,
- Di-isononyl phthalate (DINP) April 1, 2010
- Di-isodecyl phthalate (DIDP) < Excluding the following>
Optional Sample Pre-Screen Using Infrared (IR)
Spectrometry
Textile components (toys intended for Formaldehyde [for EN 71-9: 2005 4.3.1
children under 3 years) Test method for compliance testing for EN 71-9: 2005
4.3.1]
Annex III
(Notification Letter No.: HOKLAS003-250; Effective Date of termination: 25 March 2020)

Chemical analysis :-
General textiles and garments - Free formaldehyde content BS EN ISO 14184-1: 2011
ISO 14184-1: 2011

10
Cl. 4.2, Annex B
4.2, B
Page 1 of 3

10
EMC tests :-
Emission tests
- luminaires other than starter-switch operated voltages at mains terminals, load terminals
type fluorescent lamp luminaires and control terminals
- self-ballasted lamps - 9 kHz to 30 MHz
- independent light regulating devices - Measurement of radiated electromagnetic
- independent ballasts for fluorescent and other disturbances
discharge lamps - 9 kHz to 300 MHz
Page 2 of 3

10
Electrical tests :-
Section 4.25
ASTM F963-16
Section 4.25
Electric toys supplied at extra-low voltage - Compliance inspection and safety tests AS/NZS 62115: 2011
IEC 62115: 2003 + A1: 2004 + A2: 2010
Toys Flammability test :- ASTM F963-16 Cl. 4.2
ASTM F963-11 Cl. 4.2
Page 3 of 3

10
Physical and mechanical tests :-
Toys ASTM F963-16
Safety requirements :- Cl. 4.3.7, 4.5 to 4.14, 4.16 to 4.24, 4.26 to 4.28,
4.30 to 4.36, 4.38 to 4.41
Test methods Cl. 8
ASTM F963-11
Safety requirements :- Cl. 4.5 to 4.14, 4.16 to 4.24, 4.26 to 4.28,
4.30 to 4.36, 4.38, 4.39
Cl.4.6.2, 4.8.1, 4.20.1
Test methods Cl. 8
NL HOKLAS003-244 Annex II Page 1 of 1

10
Paper components (toys intended for Formaldehyde EN 71-9: 2005 4.3.2
children under 3 years) Test method for compliance testing for EN 71-9: 2005
4.3.2
Page 1 of 1
(Notification letter No.: HOKLAS003-243; Effective Date of Termination: 23 July 2019)

10
Chemical Testing
as applicable to App. A.3.3
< Excluding the following >
BS 4662: 1970 (1989) Cl. 1.7
as applicable to the tests specified in Cl. 1.10
Cl. 1.10.2
Iron and steel articles Uniformity of galvanized ( hot dip ) coatings BS 729: 1971 (1986) Cl. 11 & 14
Page 1 of 3

10
Household and similar electrical appliances

<Excluding the following> CNCA-C07-01: 2014
- three-phase blenders

10
Lighting apparatus

- Fixed general purpose luminaires EMC test as specified in GB 17743-2007
- Starter-switch operated type fluorescent lamps
luminaires
<>
luminaires
<>
-
-
- Portable general purpose luminaires EMC test as specified in GB 17743-2007
luminaires
<>

10
Luminaires, lamps and associated accessories - Measurement of conducted disturbance GB17743-2007
- luminaires other than starter-switch operated voltages at mains terminals, load terminals
type fluorescent lamp luminaires and control terminals
- self-ballasted lamps - 9 kHz to 30 MHz
- independent light regulating devices - Measurement of radiated electromagnetic
- independent ballasts for fluorescent and other disturbances
discharge lamps - 9 kHz to 300 MHz
-
- -
-
List of activities for which accreditation has been terminated
(Notification Letter: HOKLAS003-235; Effective date of termination: 19 September 2018) The Hong Kong Standards and Testing Centre Ltd. 10, Dai Wang Street, Taipo Industrial Estate, Tai Po, New Territories, Hong Kong 10

Flammability tests :- General textiles and garments - Apparel textiles - Flame propagation ASTM D1230-10 (2016)e1 ASTM D1230-10 ASTM D1230-94 (Reapproved 2001)
Page 1 of 1
Page 1 of 4
(Notification Letter: HOKLAS003-232; Effective date of termination: 15 May 2018)

10
Toys

- Electric toys All required tests as specified in GB 6675-2003 + A1-2005
<Excluding the following> CNCA-13C-069: 2010 GB 19865:2005
- toys containing gas or liquid
- toys intended to be used in water
- toys likely to be cleaned with liquid
- CNCA-13C-069: 2010 GB 6675-2003 + A1-2005
<> GB 19865:2005
-
-
-
- Plastic toys All required tests as specified in GB 6675-2003 + A1-2005
<Excluding the following> CNCA-13C-070: 2010
- CNCA-13C-070: 2010 GB 6675-2003 + A1-2005
<>
-
- Metal toys All required tests as specified in GB 6675-2003 + A1-2005
- CNCA-13C-071: 2010 GB 6675-2003 + A1-2005
<>

10
Toys (cont’d)
()
- Projectile toys All required tests as specified in GB 6675-2003 + A1-2005
- CNCA-13C-072: 2010 GB 6675-2003 + A1-2005
<>
- Dolls All required tests as specified in GB 6675-2003 + A1-2005
- CNCA-13C-073: 2010 GB 6675-2003 + A1-2005
<>

10
Flammability test
liquids,flammable liquids, flammable gels and
highly flammable solids

10
ASTM F963-07(e1)
Safety requirements :-
Page 1 of 3

10
Flammability test
highly flammable solids
Tests for flammable gases, extremely flammable
liquids, highly flammable liquids, flammable
liquids and flammable gels
Page 2 of 3

10
Toys ISO 8124-1: 2012
EN 71-1: 2011 + A2:2013
4.11 c), 4.11 e), 4.15.1.3, 4.15.1.5, 4.15.2,
4.15.3, 4.15.5, 4.18 (test to EN 15649-3), 4.20
Children’s jewelry ASTM F2923-11
- Mechanical Requirements for Children’s 12
jewelry

10
Safety and performance tests :-
Soothers for babies and young children - Safety requirements and product BS EN 1400-1: 2002
information
- Performance of the soother 5
- Testing 6
Annex III List of tests for which accreditation has been terminated
(Notification Letter No.: HOKLAS003-226; Effective Date of termination: 22 November 2017)
The accreditation of the following tests has been terminated
Care performance tests :- General textiles and garments - Dimensional stability to washing (textiles) AATCC Test Method 135-2014 AATCC Test Method 135-2012 AATCC Test Method 135-2010 Chemical analysis :- General textiles and garments - pH value AATCC Test Method 81-2012 AATCC Test Method 81-2006 Colour fastness tests :- General textiles and garments - Rubbing / Crocking AATCC Test Method 8-2013 AATCC Test Method 8-2007 Colour measurement tests :- General textiles and garments - Whiteness of textile AATCC Test Method 110-2011 AATCC Test Method 110-2005 Construction tests :- General textiles and garments - Twists in yarn BS EN ISO 2061: 2010 ISO 2061: 2010 BS EN ISO 2061: 1996 ISO 2061: 1995 Performance tests :- General textiles and garments - Abrasion resistance (Martindale tester) ASTM D4966-12 ASTM D4966-10 - Weathering resistance to UV ASTM G154-12a ASTM G154-06 BS EN ISO 4892-3: 2013 ISO 4892-3: 2013 ISO 4892-3: 2006
NL No. HOKLAS003-226, Annex III Page 1 of 1
Annex III List of test for which accreditation has been terminated
(Notification letter No.: HOKLAS003-225; Effective date of termination: 20 November 2017)
The Hong Kong Standards and Testing Centre Ltd. 10, Dai Wang Street, Taipo Industrial Estate, Tai Po, New Territories, Hong Kong 10
Food

The accreditation of the following test has been terminated Oil and fat Characteristic of oil and fat :- - Peroxide value BS EN ISO 3960: 2010
NL No. HOKLAS003-225, Annex III Page 1 of 1
Page 1 of 3

10
Electrical and electronic products
- Fixed general purpose luminaires CNCA-C10-01: 2014
- Recessed luminaires
-

10
EMC tests :-
Emission tests
Unintentional radiators - Measurement of radiated emission 47 CFR Part 15 Subparts A and B
- 9 kHz to 40 GHz using test method specified in ANSI C63.4-2009
- Measurement of conducted emission
Low power transmitters operating at frequencies - Measurement of radiated emission 47 CFR Part 15 Subparts A and C
below 1 GHz, and low power transmitters - 9 kHz to 40 GHz using test method specified in ANSI C63.4-2009
operating at frequencies above 1 GHz or ANSI C63.10-2009
- Measurement of conducted emission
Lighting equipment without intentional radiator - Measurement of induced current density EN 62493: 2010
due to the electric field IEC 62493: 2009
-20 kHz to 10 MHz
Low-voltage switch mode power supplies - Harmonic current EN 61204-3: 2001
- Voltage fluctuations and flicker IEC 61204-3: 2011
- Mains terminal disturbance voltage
- Measurement of disturbance power
- Measurement of radiated disturbances
Telecommunications equipment tests :-
Radio Equipment Exempted From Licensing Test For Transmitter: HKTA 1035 Issue 6 (2011)
- Fundamental Emission

10
Electrical tests :-
Section 4.25
Electric toys supplied at extra-low voltage - Compliance inspection and safety tests BS EN 62115: 2005 + A11: 2012
EN 62115: 2005 + A11: 2012
NL No. HOKLAS003-219, Annex II Page 1 of 2
Annex II List of tests for which accreditation has been terminated
(Notification Letter No.: HOKLAS003-219; Effective Date of termination: 10 July 2017)
Food
General foodstuff - Benzoic acid and sorbic acid In-house method CFD/STP/FOD/253 (By HPLC-DAD) - Salicylic acid In-house method CFD/STP/FOD/255 (By HPLC-DAD)
- Methyl para-hydroxybenzoate In-house method CFD/STP/FOD/256 - Ethyl para-hydroxybenzoate (By HPLC-DAD) - Propyl para-hydroxybenzoate Soy and seasoning sauces - 3-chloro-1,2-propandiol (3-MCPD) In-house method CFD/STP/FOD/214 - Dry Matter AOAC Official Method 925.09
NL No. HOKLAS003-219, Annex II Page 2 of 2
(Notification Letter No.: HOKLAS003-219; Effective Date of termination: 10 July 2017)
Toys and Children’s Products

The accreditation of the following tests has been terminated Chemical tests :- All toys - Migration of certain elements: EN71-3: 2013 Category III toy materials: Scraped-off materials Aluminum, Antimony, Arsenic, Technique used: ICP-MS Barium, Boron, Cadmium, Chromium, Cobalt, Copper, Lead, Manganese, Mercury, Nickel, Selenium, Strontium, Tin and Zinc Chromium (VI) and Technique used: IC-ICP-MS Chromium (III) (by calculation)
Japan Toy Safety Standard ST2012 (2012.9.27), English version, Part 3 All toys’ materials - Colouring matters Cl. 1.1 Materials which are mainly composed of - Consumption of potassium permanganate Cl. 1.2 polyethylene, polyvinyl chloride (excluding and residue on evaporation parts on which paint coating is applied) - Heavy metals - Arsenic - Cadmium (excluding materials mainly
composed of polyethylene) Decalcomania, folded paper and rubber-made toys - Heavy metals Cl. 1.3 (excluding rubber pacifiers) - Arsenic Vinyl chloride resin coating - Consumption of potassium permanganate, Cl. 1.4 - Residue after evaporation The paint coating applied to the body or - Heavy metals : 8 elements (antimony, Cl. 1.5 the components of the toys (excluding the arsenic, barium, cadmium, chromium, lead, printing ink used for paper containers) mercury and selenium) Textile products used for toys - Free formaldehyde Cl. 1.6 Ink and the like used for the graphic instruments - Colouring matters Cl. 1.8 that are provided with the toys such as pencils, - Heavy metals : 8 elements (antimony, ball-point pens, markers, crayons, pastels, arsenic, barium, cadmium, chromium, lead, water colours, chalks, etc. mercury and selenium)
Synthetic resin mainly composed of PVC, PU and - Bis (2-ethylhexyl) phthalate (DEHP) Cl. 1.9 Rubber - Dibutyl phthalate (DBP) Test procedure for compliance testing of PVC: - Butyl benzyl phthalate (BBP) Cl. 2.10 - Di-isononyl phthalate (DINP) Test procedure for compliance testing of PU and - Di-isodecyl phthalate (DIDP) rubber: - Di-n-octyl phthalate (DNOP) CPSC Test method: CPSC-CH-C1001-09.3 Standard Operating Procedure for Determination
of Phthalate (April, 1, 2010) <Excluding the following> Optional Sample Pre-Screen Using Infrared (IR) Spectroscopy Metals used for toy (neither painted nor covered) - Lead Cl. 1.11
Annex III
List of activities for which accreditation has been terminated
(Notification Letter: HOKLAS003-214; Effective date of termination: 9 January 2017) The Hong Kong Standards and Testing Centre Ltd. 10, Dai Wang Street, Taipo Industrial Estate, Tai Po, New Territories, Hong Kong 10
Electrical and Electronic Products
Safety tests :- Audio, video and similar electronic apparatus and - Tests for degrees of protection provided by BS EN 60529: 1992 with Amd. 7643 and information technology equipment enclosures of equipment against ingress of water Amd. 10931+A2: 2013 with index from IPX1 to IPX8 EN 60529: 1991 + A1: 2000 +A2: 2013
IEC 60529: 1989 + A1: 1999 +A2: 2013 (Note: The above three standards should be used in conjunction with the relevant product test standards as detailed in IEC 60950-1, IEC 60065)
Page 1 of 1
(Notification letter No.: HOKLAS003-211; Effective Date of Termination: 29 November 2016)
The Hong Kong Standards and Testing Centre Ltd. 10, Dai Wang Street, Taipo Industrial Estate, Tai Po, New Territories, Hong Kong 10
Environmental Testing

Trace metals (Total recoverable):- Tap Water (having a turbidity of ≥ 1 NTU) - Cadmium, Chromium, Lead, Nickel In-house method CFD/STP/ENV/203 (by ICP-MS)
NL HOKLAS003-211 Annex III Page 1 of 1
(Notification letter No.: HOKLAS003-205; Effective Date of Termination: 20 May 2016)
The Hong Kong Standards and Testing Centre Ltd. (Laboratory at Taipo Industrial Estate)
TEST CATEGORY

TOYS and CHILDREN’S All toys - Migration of the elements AS/NZS ISO 8124.3: 2003 + A1: 2010 PRODUCTS Antimony, Arsenic, Barium, Cadmium, ISO 8124-3: 2010 Chromium, Lead, Mercury, Selenium All toys - Migration of certain elements: EN71-3: 2013 Category III toy materials: Scraped-off materials Chromium (VI) and Technique used: LC-ICP-MS Chromium (III) (by calculation) Coloured toys - Colour fastness to perspiration and saliva DIN 53160 - 1974 Textile products - Free formaldehyde content BS EN ISO 14184-1: 1999
(Notification letter No.: HOKLAS003-202; Effective Date of Termination: 24 February 2016)
The Hong Kong Standards and Testing Centre Ltd. (Laboratory at Tai Ping Industrial Centre) TEST
CATEGORY
The accreditation of the following tests has been terminated.
TEXTILES and GARMENTS Strength tests :- Specific products:- - Footwear - Uppers and linings - Test methods for uppers, lining and BS EN 13572: 2002 method B (leather) insocks –seam strength < Excluding the following > Cl. 5.2.3
(Notification letter No.: HOKLAS003-200; Effective Date of Termination: 27 November 2015)
0BThe Hong Kong Standards and Testing Centre Ltd. (Laboratory at Taipo Industrial Estate) 1BTEST
2BCATEGORY 3B
6B
10BSPECIFICATION, STANDARD METHOD 11BOR TECHNIQUE USED
12B
1 3 BThe accreditation of the following tests has been terminated
TOYS and CHILDREN’S Stuffing materials in Toys Objectionable matter ASTM F963-08 Cl. 4.3.7 PRODUCTS Test procedures for compliance testing: In-house method TCD/TPM/CHM/075
(Notification letter No.: HOKLAS003-198; Effective date of termination: 30 October 2015)
0BTEST 1BCATEGORY
5B
11B The accreditation of the following tests has been terminated.
TOYS and Flammability tests CHILDREN’S Toys ASTM F963-08 4.2 PRODUCTS Japan Toy Safety Standard ST2002, Tenth Edition, 2010.4.1, Part 2 (based on English version of the Ninth Edition and revision published by JTA in March 2010) Physical and mechanical tests Toys ISO 8124-1: 2009 BS EN 71-1: 2011 EN 71-1: 2011 Japan Toy Safety Standard ST2002 Tenth Edition, 2010.4.1, Part 1(based on English version of the Ninth Edition and revision published by JTA in March 2010)
Annex II List of test for which accreditation has been terminated
(Notification letter No.: HOKLAS003-197; Effective date of termination: 27 October 2015) The Hong Kong Standards and Testing Centre Ltd.
CATEGORY
TEXTILES and GARMENTS Strength tests :- Specific products:- - Footwear
- Whole shoe - Strength of attachment of straps and nailed SATRA TM 120: 2001 or stapled uppers
HOKLAS003-197 Annex II Page 1 of 1
(Notification letter No.: HOKLAS003-196; Effective date of termination: 30 October 2015)
0BTEST 1BCATEGORY
5B
11B The accreditation of the following tests has been terminated.
TOYS and Flammability tests CHILDREN’S Toys ASTM F963-08 4.2 PRODUCTS Japan Toy Safety Standard ST2002, Tenth Edition, 2010.4.1, Part 2 (based on English version of the Ninth Edition and revision published by JTA in March 2010) Physical and mechanical tests Toys ISO 8124-1: 2009 BS EN 71-1: 2011 EN 71-1: 2011 Japan Toy Safety Standard ST2002 Tenth Edition, 2010.4.1, Part 1(based on English version of the Ninth Edition and revision published by JTA in March 2010)
(Notification letter No.: HOKLAS003-194)
2BCATEGORY 3B
6B
12B
FOOD Food containers - Leachable cadmium and lead DIN 51032 - 1986 .3. (ceramic ware) Test procedures for compliance testing of Australian .3. Commonwealth Consolidated Regs. 1956, Reg. 4E:- BS 4860: Parts 1 and 2: 1972 .3. Food containers - Leachable cadmium Test procedures for compliance testing of US FDA .4. (silver ware) Compliance Policy Guides 7117.05 (2005): Food containers - Migration of primary aromatic amine European Commission Joint Research Centre - .3. (polyamide kitchenware) (time-temperature exposure conditions Technical Guidelines on Testing the Migration other than 2 hours at 70 °C and 2 hours of Primary Aromatic Amines from Polyamide at 100 °C) Kitchenware and of Formaldehyde from Melamine Kitchenware, EUR 24815 EN 2011, Section 7 (time-temperature exposure conditions other than 2 hours at 70 °C and 2 hours at 100 °C) conforming to the relevant sections of BS EN 13130-1:2004 .3. (sample preparation) Food containers - Formaldehyde and HMTA European Commission Joint Research Centre - .3. (Melamine kitchenware) (time-temperature exposure conditions Technical Guidelines on Testing the Migration other than 2 hours at 70 °C) of Primary Aromatic Amines from Polyamide Kitchenware and of Formaldehyde from Melamine Kitchenware, EUR 24815 EN 2011, Section 7 (Sample preparation – time-temperature exposure conditions other than 2 hours at 70 °C) - Melamine Commission Regulation (EU) No. 1282/2011 .3. (time-temperature exposure conditions of 28 November 2011 other than 2 hours at 70 °C) BS EN 13130-1: 2004 (Sample preparation – .3. 3% (w/v) acetic acid as simulant; time-temperature exposure conditions other than 2 hours at 70 °C) Milk and dairy products - Milk fat AOAC (1990) 905.02 .3. General foodstuff - Sulphur dioxide AOAC Official Method 990.28 (2000) .3. - Salmonella US FDA Bacteriological Analytical Manual Online .3. (BAM online), Ch. 5, February 2011 (Isolation and Identification) - Mold and yeast (total) counts US FDA Bacteriological Analytical Manual Online .3. (BAM online), Ch. 18, January 2001 (Conventional Plate Count Method)
16BCATEGORY 17B
20B
21BSPECIFIC TEST OR 2 2 BPROPERTY MEASURED 2 3 B
26B
MISCELLANEOUS Cosmetics, liquids, - Microbial Limit Tests USP < 61 > & < 62 > 34th edition .3. pastes, putties, gels (Microbiological indicators by Pour Plate Method) and powders (Pathogens by Isolation and Identification) TOYS and Toy cosmetics, liquids, - Microbial Limit Tests USP < 61 > & < 62 > 34th edition .3. CHILDREN’S pastes, putties, gels and (Microbiological indicators by Pour Plate Method) PRODUCTS powders (Pathogens by Isolation and Identification) Canada Consumer Products Safety Act .2. Children’s Jewellery Regulations, SOR/2011-19 Toys - Migration lead Test procedures for compliance testing: Product Safety Laboratory Book 5 - Laboratory .2. Policies and Procedures Part B: Test Methods Section, Method C08 Determination of Migration Lead in Consumer Product . Canada Surface Coating Materials Regulations, .3. SOR/2005-109 - Total mercury Test procedures for compliance testing: Product Safety Bureau Reference Manual Book 5 - .3. Laboratory Policies and Procedures Part B: Test Method Section, Method C07 Determination of Total Mercury in Surface Coating Materials Canada Surface Coating Materials Regulations, .2. SOR/2005-109 - Soluble elements Test procedures for compliance testing: Product Safety Bureau Reference Manual Book 5 - .2. Laboratory Policies and Procedures Part B: Test Method Section, Method C03.1 Determination of Leachable Arsenic, Selenium Cadmium, Antimony and Barium Canada Toys Regulations, SOR/2011-17, Section 23 .3. - Total mercury Test procedures for compliance testing: Product Safety Bureau Reference Manual Book 5 - .3. Laboratory Policies and Procedures Part B: Test Method Section, Method C07 Determination of Total Mercury in Surface Coating Materials All toys - Migration of the elements DIN EN 71-3: 1995 .1. Antimony, Arsenic, Barium, Cadmium, NF EN 71-3: 1995 .1. Chromium, Lead, Mercury, Selenium
Note: .1. Effective date of termination: 25 August 2015 .2. Effective date of termination: 1 September 2015 .3. Effective date of termination: 4 September 2015 .4. Effective date of termination: 15 September 2015
(Notification letter No.: HOKLAS003-192; Effective date of termination: 13 July 2015) The Hong Kong Standards and Testing Centre Ltd.
The Hong Kong Standards and Testing Centre Ltd. (Laboratory at Taipo Industrial Estate) TEST
CATEGORY
TEXTILES and GARMENTS Flammability tests :- Specific Products : - Curtains and drapes - Vertical test NFPA 701: 2004 Test Method 1 < Excluding the following> Cl. 16.3.1(1)
CATEGORY
CONSTRUCTION MATERIALS Bathroom and kitchen sets - Showers for bathing Performance tests :- AS/NZS 3662: 2005 + A1: 2006 + A2: 2009 < Excluding the following > - High pressure flow rate + A3: 2010 - shower hoses - Low pressure or unequal pressure flow rate <Excluding the following> - Mean spray spread angle Cl. 5.4 - Temperature drop - Flow controller endurance - Marking - Showers for bathing Performance tests :- The Hong Kong Voluntary Water Efficiency Labelling - Nominal flow rate Scheme on Showers for Bathing (December 2011) - Mean spray spread angle Annex1 Section I and Section II - Temperature drop - Flow controller endurance
- Tap ware Performance tests :- AS/NZS 3718: 2005 + A1: 2006 + A2: 2008 - High pressure flow rate App. G, Q and R - Low pressure or unequal pressure flow rate - Flow controller endurance - Water taps Performance tests :- The Hong Kong Voluntary Water Efficiency Labelling - Nominal flow rate Scheme on Water Taps (December 2012) Annex1 - Flow controller endurance Section I and Section II
CATEGORY
TEXTILES and GARMENTS Colour fastness tests :- General Textiles and - Dry cleaning AATCC Test Method 132-2004 garments - Rubbing / Crocking AATCC Test Method 8-2005 - Washing - Accelerated laundering: AATCC Test Method 61-2007
- Water AATCC Test Method 107-2009
Other materials :- - Leather - To-and-fro rubbing BS EN ISO 11640: 2012 EN ISO 11640: 2012 ISO 11640: 2012 IULTCS/IUF 450: 2012 Construction tests :- General Textiles and - Mass per unit area (weight) ASTM D3776-96 (Reapproved 2002) garments Specific products:- - Footwear - Footwear materials - Soling materials - Density of material by volume displacement SATRA TM 134: 1998 BS 903-A1: 1996 Method A ISO 2781: 1988 + Cor 1: 1996 Method A ISO 2781: 2008 + A1: 2010 Method A - Uppers and linings - Mass per unit area SATRA TM 28: 1994 (leather)
CATEGORY
TEXTILES and GARMENTS Strength tests :- (cont’d) General Textiles and - Tearing strength (falling pendulum) ASTM D1424-96 () garments
Specific products:- - Footwear - Footwear materials - Fasteners, buckles - Strength of buckle and strap attachment SATRA TM 181: 1996 and trims BS 5131-5.11: 1981 - Heels (top piece) - Strength of top-piece attachment SATRA TM 108: 1992 - Threads and elastics - Measurement of the strength of stitched SATRA TM 180: 1995 seams in upper and lining materials < Excluding the following > Cl. 5.2
BS 5131-5.13: 1980 < Excluding the following > Cl. 5.1 - Whole shoe - Attachment strength of decorative bows SATRA TM 117: 1992 - Measurement of the strength of attachment SATRA TM 113: 1996 of heels to footwear and the backpart BS EN 12785: 2000 rigidity of footwear EN 12785: 2000 ISO 22650: 2002 - Strength of sandal toe posts SATRA TM 118: 1992
(Notification letter No.: HOKLAS003-191; Effective Date of Termination: 1 July 2015)
2BCATEGORY 3B
6B
12B 1 3 BThe accreditation of the following tests has been terminated.
TOYS and CHILDREN’S Chemical tests :- PRODUCTS Toys - paint and similar - Total lead content ASTM F963-08, Cl. 4.3.5.1 surface-coating materials - Migration of the elements ASTM F963-08, Cl. 4.3.5.2 Antimony, Arsenic, Barium, Cadmium, Chromium, Lead, Mercury, Selenium
List of tests for which accreditation has been terminated (Notification letter No.: HOKLAS003-191; Effective Date of Termination: 1 July 2015)
16BCATEGORY 17B
20B
2 1 BSPECIFIC TEST OR 2 2 BPROPERTY MEASURED 2 3 B
TOYS and Chemical tests :- (cont’d) CHILDREN’S Japan Toy Safety Standard ST2002 PRODUCTS Eleventh Edition, 2011.8.23, Part 3 (cont’d) (based on English version of the Ninth Edition and revision published by JTA in March 2010 and () August 2011) All toys’ materials - Colouring matters Cl. 1.1 Materials which are mainly - Consumption of potassium permanganate Cl. 1.2 composed of polyethylene, and residue on evaporation polyvinyl chloride - Heavy metals (excluding parts on - Arsenic which paint coating is - Cadmium (excluding materials mainly applied) composed of polyethylene) Decalcomania, folded paper - Heavy metals Cl. 1.3 and rubber-made toys - Arsenic (excluding rubber pacifiers) Polyvinyl chloride resin - Consumption of potassium permanganate, Cl. 1.4 coating - Residue after evaporation The paint coating applied to - Heavy metals : 8 elements (antimony, Cl. 1.5 the body or the components arsenic, barium, cadmium, chromium, lead, of the toys (excluding the mercury and selenium) printing ink used for paper containers) Textile products used for toys - Free formaldehyde Cl. 1.6 Ink and the like used for the - Colouring matters Cl. 1.8 graphic instruments that are - Heavy metals : 8 elements (antimony, provided with the toys such arsenic, barium, cadmium, chromium, lead, as pencils, ball-point pens, mercury and selenium) markers, crayons, pastels, water colours, chalks, etc. Synthetic resin mainly - Bis (2-ethylhexyl) phthalate (DEHP) Cl. 1.9 composed of PVC, PU and - Dibutyl phthalate (DBP) Test procedures for compliance testing of PVC: Rubber - Butyl benzyl phthalate (BBP) Cl. 2.10
- Di-isononyl phthalate (DINP) Test procedures for compliance testing of PU and rubber:
- Di-isodecyl phthalate (DIDP) CPSC Test method: CPSC-CH-E1001-09.3 Standard - Di-n-octyl phthalate (DNOP) Operating Proceudre for Determination of Phthalate (April, 1, 2010) Metals used for toy (neither - Lead Cl. 1.11 painted nor covered)
List of tests for which accreditation has been terminated (Notification letter No.: HOKLAS003-191; Effective Date of Termination: 1 July 2015)
30BCATEGORY 31B
34B
3 7 B
TOYS and CHILDREN’S Chemical tests :- (cont’d) PRODUCTS (cont’d) Specifications and Standards for Foods, Food Additives, etc. Under the Food Sanitation Law () (ABSTRACTS) JETRO January 2009, Part V “TOYS” English Versions of Japan Sanitation Law, Ministry of Health and Welfare Notification No. 370, 28 Nov 1959 and Notification No. 153, March 2008 Test method for compliance testing of toys under Food Sanitation Law in Japan:- Specifications, Standards and Testing Methods for Foodstuffs, Implements, Containers and Packaging, Toys, Detergents, January 2009 Part III. Standards and Testing Methods for Toys: Decals Heavy metals, Arsenic Section A-1 Origami paper Heavy metals, Arsenic Section A -2 Coating film of toys Cadmium, lead, Arsenic Section A-4 Coating film coated by using Consumption of potassium permanganate, Section A-5 polyvinyl chloride Residue on evaporation Materials composed mostly Heavy metals, Arsenic, Cadmium, Section A-6 of polyvinyl chloride (except Consumption of potassium permanganate, polyvinyl chloride coatings) Residue on evaporation PVC DEHP Section A-7 PVC DINP Section A-8 Parts (excluding coating Heavy metals, Arsenic, Section A-9 film) manufactured using Consumption of potassium permanganate, materials mainly of Residue on evaporation polyethylene Metallic accessories and toys Lead Section A-10 Toys production standards Colouring agent Section B
Annex IV
List of activities for which accreditation has been terminated (Notification letter no. 003-186; Effective date of termination: 17 November 2014)
2BCATEGORY 3B
6B
7BSPECIFIC TEST OR 8BPROPERTY MEASURED 9B
12B PHYSICAL and MECHANICAL Polymer and Polymer TESTING Products - Female condoms Performance tests: - ISO 25841: 2011 - lubricant mass for individual female <Excluding the following> condoms containers Cl. 4, 5.1-5.3, 5.6, 6, 7, 8, 10 and 14, - dimensions Annex A, B, H, K and L - condom package integrity - bursting volume and bursting pressure - freedom of holes and visible defects - Male condoms made from Performance tests: - ISO 23409: 2011, Cl. 8.2 and Annex C synthetic materials - total lubricant for condoms in <Excluding the following> individual containers Cl. 4, 5, 6, 7, 9, 10, 13 and 17.1, - dimensions Annex A, B, G, I, K and L - bursting volume and bursting pressure - holes (water leak test) - individual container integrity - oven treatment - Natural latex rubber Performance tests : - AS 5074: 2009 condoms - total lubricant for condoms in BS EN ISO 4074: 2002 with Corr. 1 & Technical individual containers Corr. 1 ISO 4074: 2002 with Corr. 1 & Corr. 2 - dimensions GB 7544-2004 GB 7544-2009 - bursting volume and bursting pressure <Excluding the following> For the above four standards - oven treatment Cl. 4, 6.3.3 and 7, Annex A, B, J and K - force and elongation at break <> 4, 6.3.3 7 - holes (water leak test) A, B, J K - package integrity - Polyurethane male condom Performance tests: - ASTM D6324-11 - dimensions <Excluding the following> - tensile properties (dumbbell method) Cl. 5.1.1-5.1.4 and 5.7, - leakage Annex X3 and X4 - air burst - packaging
NL003-186 Annex IV Page 1 of 6
15BCATEGORY 16B
19B
25B TEXTILES and GARMENTS Care performance tests :- General Textiles and - Spirality (plain knitted garments) WOOLMARK TWC-TM 276-2009 garments Chemical analysis :- General Textiles and - pH value BS EN 1413: 1998 garments EN 1413: 1998 - Wool textiles - Oil content WOOLMARK TWC-TM 136-2009 Colour fastness tests :- General Textiles and - Washing AS 2001.4.15-1994 garments AS 2001.4.15-2006 Other materials :- - Leather - Rubbing (reciprocating method) SATRA TM 173: 1995 using Type 2 machine - Water spotting of leathers, textiles and SATRA TM 185: 1995 coated fabrics Specific products:- - Footwear - Footwear materials - uppers and linings - Rubbing (circular) SATRA TM 8: 2004 (leather) ISO 17700: 2004 Method B - Rubbing (reciprocating method) SATRA TM 173: 1995 Using Type 2 machine - Water spotting of leathers, textiles and SATRA TM 185: 1995 coated fabrics Construction tests :- General Textiles and - Length of sewing threads ASTM D204-02 (Reapproved 2010) , section 34-42 garments - Linear density of yarn by the skein method ASTM D1907-07 ASTM D1907-12 BS EN ISO 2060: 1995
28BCATEGORY 29B
32B
38B TEXTILES and GARMENTS Flammability tests :- (cont’d) General Textiles and () garments - Apparel textiles - Flame propagation US CS 191 - 53 (Revised) - Pile fabrics and assemblies - Ignitability (surface flash) BS 4569: 1983 having pile on the surface Performance tests :- General Textiles and - Pilling resistance (ICP pilling box method) WOOLMARK TWC-TM 152-2009 garments Other materials :- - Leather - Flexing resistance ISO 5402: 2002 IULTCS/IUP 20: 2002 ISO 5402-1: 2011 IULTCS/IUP 20-1: 2011 Specific products:- - Footwear - Footwear materials - heels - Fatigue test for shoe heels SATRA TM 21: 2001 BS EN ISO 19956: 2004 EN ISO 19956: 2004 ISO 19956: 2004 BS 5131: Section 4.9 : 1991 - soling materials - Hardness of rubber and plastics SATRA TM 205: 1999 using Type A or Type D Durometers - Hardness of rubber ASTM D2240- 05 (Reapproved 2010) using Type A or Type D Durometers BS EN ISO 868: 2003 + Cor 1: 2003 - Hardness of rubber and plastics SATRA TM 206: 1999 Method N (IRHD method) BS 903-A26: 1995 Method N BS ISO 48: 2010 Method N ISO 48: 2010 Method N BS ISO 48: 2007 + Corr. 1 Method N ISO 48: 2007 + TC1 Method N
41BCATEGORY 42B
45B
51B TEXTILES and GARMENTS Performance tests :- (cont’d) (cont’d) Specific products:- () - Footwear - Footwear materials - uppers and linings - Abrasion resistance (Martindale method) BS EN 13520: 2002 + A1: 2005 (leather) SATRA TM 31 : 2003 + Amdt. 1 Methods A and B - Flexing resistance of uppers and linings SATRA TM 55: 1999 BS EN 13512: 2002 EN 13512: 2001 < Excluding the following > For the above three standards Cold test - Resistance to creasing and cracking SATRA TM 25: 1992 (Vamp flex test) BS 3424 Part 9: 1990 Method 11C < Excluding the following > For the above two standards Cold test - Woven and knitted fabrics - Abrasion resistance BS 2543: 1991, Annex B for upholstery - Pile tuft/fibre loss by reverse abrasion BS 2543: 1991, Annex C
54BCATEGORY 55B
58B
64B TEXTILES and GARMENTS Performance tests :- (cont’d) (cont’d) Specific products:- () - Footwear - Footwear materials - heels - Fatigue test for shoe heels SATRA TM 21: 2001 BS EN ISO 19956: 2004 EN ISO 19956: 2004 ISO 19956: 2004 BS 5131: Section 4.9 : 1991 - soling materials - Hardness of rubber and plastics SATRA TM 205: 1999 using Type A or Type D Durometers - Hardness of rubber ASTM D2240- 05 (Reapproved 2010) using Type A or Type D Durometers BS EN ISO 868: 2003 + Cor 1: 2003 - Hardness of rubber and plastics SATRA TM 206: 1999 Method N (IRHD method) BS 903-A26: 1995 Method N BS ISO 48: 2010 Method N ISO 48: 2010 Method N BS ISO 48: 2007 + Corr. 1 Method N ISO 48: 2007 + TC1 Method N - uppers and linings - Abrasion resistance (Martindale method) BS EN 13520: 2002 + A1: 2005 (leather) SATRA TM 31 : 2003 + Amdt. 1 Methods A and B - Flexing resistance of uppers and linings SATRA TM 55: 1999 BS EN 13512: 2002 EN 13512: 2001 < Excluding the following > For the above three standards Cold test - Resistance to creasing and cracking SATRA TM 25: 1992 (Vamp flex test) BS 3424 Part 9: 1990 Method 11C < Excluding the following > For the above two standards Cold test - Woven and knitted fabrics - Abrasion resistance BS 2543: 1991, Annex B for upholstery - Pile tuft/fibre loss by reverse abrasion BS 2543: 1991, Annex C
67BCATEGORY 68B
71B
77B TEXTILES and GARMENTS Strength tests :- (cont’d) Specific products:- () - Footwear - Footwear materials - Fasteners, buckles - Closure strength of touch and close fasteners SATRA TM 123: 1992 and trims (peel and shear strength) - Closure strength of touch and close fasteners BS EN ISO 22776: 2004 (shear strength) EN ISO 22776: 2004 ISO 22776: 2004 - Closure strength of touch and close fasteners BS EN ISO 22777: 2004 (peel strength) EN ISO 22777: 2004 ISO 22777: 2004 - Slide fastener burst strength SATRA TM 166: 1992 - Insole - Pin holding strength of insole materials SATRA TM 11: 1993 BS EN 12745: 1999 - Tensile properties of insole materials SATRA TM 2: 1995 - Laces and eyelets - Attachment strength of eyelets fastenings SATRA TM 150: 1999 - Knot spillage test SATRA TM 195: 2004 - Strength of eyelet facings and other laced SATRA TM 149: 1999 fastenings - Uppers and linings - Break/ pipiness SATRA TM 36: 1999 (leather) - Breaking strength and extension at break SATRA TM 29: 1992 ISO 17706: 2003 - Lastometer ball burst test SATRA TM 24 : 1992 ISO 3379 : 1976 - Tearing strength (Baumann method) SATRA TM 162: 1992 BS EN ISO 3377-2: 2002 + Cor 1: 2003 EN ISO 3377-2: 2002 + Cor 1: 2003 ISO 3377-2: 2002
Annex III List of activities for which accreditation has been terminated
(Notification Letter No. : 003-184; Effective date of termination: 14 May 2014) 0BTEST
1BCATEGORY 2B
5B
8 B
11B CONSTRUCTION MATERIALS Performance tests :- Bathroom and kitchen sets - Showers for bathing - Watertightness of end connections AS/NZS 3662: 2005 + A1: 2006 + A2: 2009 < Excluding the following > + A3: 2010 - shower hoses Tile Adhesives - Determination of tensile adhesion strength BS 5980: 1980 with Amd. 5861: 1989 App. D
Page 1 of 2
(Notification Letter No. : 003-184; Effective date of termination: 14 May 2014)
12BTEST 13BCATEGORY
17B
2 0 B
23B TEXTILES and GARMENTS Chemical analysis :- General textiles and - Oil content BS 3582: 1981 (1990) garments Construction tests :- - Length of sewing threads ASTM D204-02 - Twists in yarn ASTM D1423-02 Children’s upper outwear - Measurement of drawstrings ASTM F1816-97 (Reapproved 2004)
Page 2 of 2
(Notification Letter: 003-181; Effective date of termination: 10 February 2014)
0BTEST 1BCATEGORY
5B
8 B
11B MISCELLANEOUS Microbiological tests :- Cosmetics, liquids, - Microbial Limit Tests ASTM F963-08 Clause 4.3.6.3 pastes, putties, gels USP < 61 > & <62> 34th edition and powders (Microbiological indicators by Pour Plate Method) (Pathogens by Isolation and Identification) TOYS and CHILDREN’S Microbiological tests :- PRODUCTS Toy cosmetics, liquids, - Microbial Limit Tests ASTM F963-08 Clause 4.3.6.3
pastes, putties, gels and USP < 61 > & <62> 34th edition powders (Microbiological indicators by Pour Plate Method) (Pathogens by Isolation and Identification)
Page 1 of 1

Documents

Textiles and Garments 紡織品及成衣 - ITC