Test products for power systemsfrom Megger.

WW

W.M

EG

GER

.CO

M

The word ‘Megger’ is a registered trademark

Contents 1

Contents

Page

Insulation resistance testing 2-3

Insulation testing 4

High voltage test equipment 5

Protection testing 6

Automatic protective relay testing 7

Cable fault location equipment 8-9

Transformer testing 10-12

Transformer insulating oil testing 12

Watthour meter testing 13

Switches and test blocks 13

Battery testing 14-15

Earth resistance testing 16-17

Low resistance measurement 18-19

Power quality 20-21

For more than 100 years the Megger name hasbeen synonymous with high quality instrumentsfor the testing and measurement for electricalpower applications.

The trademark was first registered in May 1903and is jealously guarded by the company.

Although we’re best known for our world famousrange of insulation testers, Megger provides a fullservice solution to meet your electrical test andmeasurement needs.

Our products provide testing solutions in themost critical maintenance areas including cablefault locating, protective relay testing, and powerquality testing, as well as being the supplier ofchoice for hand-held electrical test andmeasurement instruments for electricalinstallation, data and telecom engineers.

With such a diverse product offering, we are thesingle source for electrical test and measuringinstruments.

In our 100 years Megger has built up a wealth ofexpertise in our specialist fields. You can benefitFREE from our expertise.

Megger has recently revised its publication “a guide to diagnostic insulation testing over1kV” as well as producing a selection of otheruseful applications guides. These include “thebattery testing guide”, “fault finding solutions”and “a guide to low resistance measurement”.For your copy of any of these guides return the card you will find on the inside back cover of this catalogue.

Megger offer you a complete serviceWith a constant flow of new products to assist the electrical engineer inmaking the right measurements and exciting new software packages to helpmonitor, analyse and report, Megger can also offer training to understandand operate the instruments safely and effectively.

Our training operation can be accessed globally using the web. Megger canalso offer training at your premises or at its centres in Dover, Dallas and Paris.

For more information visit: www.avotraining.com

NEW

Megger PowerDB™

Power test data analysis and certification software

Designed to manage the complete suite of test data collected from power system assets. Test forms are designed for the

majority of the electrical apparatus on the market today. PowerDB currently supports the following devices:

Batteries Generators Loadbreak Switches Switchboards

Cables Ground Fault Tests Motor Control Centers Transducers

Circuit Breakers Ground Mat/Grid Tests Power Factor Tests Transfer Switches

Coordination Data Instrument Transformers Power Transformers Watthour Meters

Disconnects Insulation Fluids Relays

The software will perform extensive information processing including equation calculations, temperature correction factors

and charting. Data trending for predictive failure analysis is accomplished by charting historical results, stored in PowerDB or

imported from other party’s proprietary database software, for any piece of equipment.

2 Insulation resistance testing Insulation resistance testing 3

Insulation resistance testing

Megger BM15 and Megger MJ15

Analogue dual supply

Easy-to-use 5kV insulation testers in a tough field case.

The MJ15 offers a unique combination of battery and

hand cranked generator to give the answer to “go / no go”

testing.

Megger MIT510 NEW

5kV insulation resistance tester

The MIT510 is an easy to operate insulation resistance tester

that is very tough. It allows automatic IR. The built-in timer

and high test ranges allow simple and quick evaluation of

the condition of the insulation under test. The MIT510 is

mains or battery powered.

Insulation resistance testingModel BM15 MJ15 MIT510 MIT520 MIT1020 S1-5010Display Graphical

Analogue

Analogue/Digital

Power supply Mains power

Rechargeable optional optional

Hand-crank

Dry cell

Test voltage 10.0kV

5.0kV

2.5kV

1.0kV

500V

250V

25V steps 50V to 5kV

10V steps 50V to 1kV

25V steps 1kV to Maxtest voltage

Measurements Max reading 20GΩ 20GΩ 15TΩ 15TΩ 35TΩ 5TΩMin reading 100kΩ 100kΩ 10kΩ 10kΩ 10kΩ 10kΩVoltage

Time constant

Capacitance

Leakage current

Test types Polarisation index

Dielectric absorption ratio

Step voltage

Dielectric discharge

Other features Timer control

Timer display

5mA test currents

3mA test currents

2mA test currents

1mA test currents

Guard terminal

USB output

RS232 output

RS232 control

Calibration Certificate

MIT510

MJ15

Megger MIT520 NEW

5kV insulation resistance tester

The MIT520 offers the ability to test insulation to 5kV.

It allows automatic IR, PI, DAR, SV and DD tests, and

results storage and download give full diagnostic

information.

The MIT520 can be powered using both mains or its

on-board rechargeable battery.

Megger MIT1020 NEW

10kV insulation resistance tester

The MIT1020 offers the ability to test insulation to 10kV, to

comply with IEEE43: 2000. It allows automatic IR, PI, DAR,

SV and DD tests, and results storage and download give full

diagnostic information.

The MIT1020 can be powered using both mains or its

on-board rechargeable battery.

Megger Series 1-5010

Diagnostic insulation tester

The Series1-5010 is a heavy-duty mains/battery powered

instrument. Offering auto test and results storage, it is a

stand-alone instrument for maximum diagnostic

information and predictive maintenance.

S1-5010

MIT1020

MIT520

4 Insulation testing High voltage test equipment 5

Insulation testing

Capacitance and dissipation factor or tanδ testing

Delta 2000

12kV fully automated capacitance and tanδtest bridge

The ultimate instrument for dissipation factor testing, the

DELTA2000 offers automatic measurement of dissipation

factor, capacitance, watts loss and leakage current. It is

ideal for the assessment of insulation in high voltage

apparatus such as transformers, bushings, circuit breakers,

cables, surge arresters and rotating machinery.

CB100

Low voltage capacitance and tanδ test bridge

Lightweight and low-cost the CB100 is ideal for workshop

use. Manually balanced it offers direct readout of tanδ and

capacitance, overcoming interference by using a test

frequency of 80 or 100Hz.

670000 series

2.5 and 12kV semi-automatic capacitanceand tanδ test bridge

These instruments feature automatic balancing of

dissipation factor and manual balancing of capacitance and

interference suppression, allowing use in energised HV

substations. There is direct readout of tanδ, capacitance and

watts dissipated.

681100 series

50/100kV a.c. dielectric test sets

681100 series a.c. dielectric test sets are a.c. high-voltage

sources for testing electrical insulation. The standard system

includes a control/instrument cabinet, a high-voltage

transformer assembly and all necessary cables including

ground and input power.

220000 series

70kV, 120kV & 160kV d.c. dielectric test set

220000 series provides a dependable, safe, lightweight and

portable d.c. voltage source for testing the quality and

integrity of electrical power cables, cable installations,

motors, switchgear, insulators, transformers and capacitors.

Insulation testingModel Delta 2000 CB100 670025 670065 670070Output voltage 12kV 28V 2.5kV 12kV 12kVCapacitance measuring range in µF 0-0.11 or 0-1.2 0-0.22 0-0.22 0-0.22 or

0-1 with inductor 0-1 with inductorDissipation factor 0-90% 0-30% 0-200% 0-200% 0-200%UST test

GST test

GST guarded test

Watts loss measurement

Current measurement

Range extension

Interference suppression Automatic Inherent Manual Manual ManualBalancing Automatic Manual Manual Manual ManualData storage

Bar code reader

PC software

RS232 printer output

Delta 2000

670000 series

High voltage test equipment

CB100

High voltage test equipmentModel d.c. output a.c. outputd.c. test sets Continuous Short circuit Continuous Short circuit220005 5kV 5mA 5mA220015 15kV 2mA 5mA220070 70kV 3.5mA 5mA220123 120kV 2.5mA 5mA220164 160kV 2mA 5mAa.c. test sets230315 3kV 12mA230415 4kV 12mA230425 5kV – 17mA 4kV 3mA 12.6mA686100 Non-resonant 50/100kV 80/150mA681100 Resonant 50/100kV 80/150mA686100 Non-resonant 50/100kV 40/75mA681100 Resonant 50/100kV 40/75mA

681100 series

200070 series

6 Protection testing Automatic protective relay testing 7

Protection testing Automatic protective relay testing

PCITS2000/2Primary current injection test setThese tough self-contained test sets are designed foroperation by one person and are comparatively light. With aseparate hand-held controller connected by an expandablecable it allows the operator to work close to a protectiverelay while controlling a test.

DDA1600, DDA3000 and DDA6000High current injection test setsDDAs are a range of high current units capable ofgenerating a test current of up to 50000A through a circuitbreaker. The instrumentation and control system enable theoperator to vary the pulse time and firing angle of theinjected signal. They can be used for testing protection relaysand low voltage circuit breakers at the commissioning stage.

CB832 and CB845Current injection setsCapable of generating up to 1800A and 5000A respectivelyfor an instantaneous trip test, these units are ideal forcommissioning applications requiring high current injection.The CB current injection sets offer adequate driving voltagefor all but the highest circuit impedance.

Protective relay test systemThe MPRT tester and AVTS® software from Megger raises the standard for the automatic testing and management of protective relay systems. The MPRT offers traditionalmanual and semi automatic testing of the relay systemwhilst the AVTS package offers fully automatic testing aswell as relay maintenance schedule management.

Megger MPRTProtective relay tester

The power unit offers a range of new features includingconstant and high power output capability through theentire power curve, the combination of voltage and currentgenerators into one amplifier package giving the flexibilityof 4 current and 4 voltage outputs or 8 current outputs fortesting multi-phase differential relays, and built-intransducer testing capability. The test set also offers 4communication ports including facilities for high speeddownloads and upgrades via the internet.

The touch-view interface makes it easier to perform manual and semi-automatic relay testing. The large colourLCD touch screen allows the operator to test virtually alltypes of relays without the need for an external computer.Menu screens and function buttons provide a quick and easy method to drive the selected test.

Megger AVTS Advanced visual test software

A version of AVTS can be supplied to meet individualcustomer’s requirements. AVTS Basic is supplied with allMPRT systems but can be upgraded to AVTS Advanced orthe full AVTS Professional packages. AVTS Basic allows fullautomatic operation of the test set with pre-prepared testfiles, whilst the Advanced and Professional options giveincreased functionality for the preparation of automatic testfiles and relay performance evaluation.

Automated relay testing enables the test engineer to save agreat deal of time and money by rapidly executing the testprocess and minimising any protected power systemequipment down time.

AVTS packages have a powerful graphical interface that isdeveloped and continuously upgraded by Megger tosimplify fully automatic and complex relay testing. It isdesigned to meet the existing and future needs ofprotection technicians and engineers worldwide helping toimprove efficiency and reduce testing errors.

K500Protective relay tool kit

A comprehensive range of relay tools containing over 40specific items. The whole kit is supplied in either alightweight soft case or a tough lockable vinyl case.

Protection testingModel CB832 PCITS2000/2 CB845 MS2 DDA1600 DDA3000 DDA6000 SCITS100 SITS120 SR90 SR98Output current In Amps 0 - 1800 0 - 2000 0 - 5000 0 - 240 0 - 19200 0 - 35000 0 - 50000 0 - 100 0 - 120 0 - 140 0 -115

Number of ranges 3 2 4 3 4 5 4Voltage output V a.c. 0 - 250 0 - 120 0 - 240 0 - 600 0 - 300

V d.c. 0 - 240 0 - 240 0 - 500 0 - 240Power In VA 1750 7200 2400 700 1400 920Time Period in S 0 - 999.99 0 - 600 0 - 999.99 0 - 999.99 0 - 99999 0 - 99999 0 - 99999 0 - 599.99 0 - 999.99 0 - 9999.99 0 - 9999.99

Resolution in S 0.001 0.01 0.001 0.001 0.0001 0.0001 0.0001 0.01 0.001 0.0001 0.0001Cycles 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999 0 - 99999.9 0 - 99999.9

MPRT8430 protective relaytest set

Primary current injection testing (PCITS) and circuit breaker testing (CBT)

SCITS100 and SITS120Current and voltage injection setsTough test sets suitable for general purpose relay testing. A wide range of relays can be tested due to their operatingsystem flexibility. Current and voltage on the outputterminals are measured and displayed. An accurate timermeasures the relay operating time. The SITS120 offers alighter option.

MS2Circuit breaker and overload relay test setThe MS2 is capable of delivering 750A instantaneously. It isideal for over-current and earth fault relays and mouldedcase circuit breakers.

Secondary current injection testing

Automatic protective relay testingRelay type IEEE no. SCITS100/2 SITS120 SR98 MPRTTime delay 2

Impedance 21

Volts per hertz 24

Synchronising 25

Directional power 32

Loss of excitation 40

Negative sequence over-current 46

Negative sequence under-voltage 47

Instantaneous over-current 50

Over-current 51

Moulded case breaker 52

Over-voltage 59

Directional over-current 67

Reclosing 79

Frequency 81

Differential 87 **

Tripping 94

Auto synchronising 25A

Voltage controlled over-current 27 / 51

Under / over voltage 27 / 59

d.c. under / over current 37 / 76

Motor overload 51 / 86

Ground directional over-current 67N

**Two units required

AVTS test screens

SR90 and SR98Voltage and current injection setsThe SR90 calibrates, performs acceptance testing andtroubleshoots the most popular solid-state and electro-mechanical relays. Tests all moulded case circuit breakers,motor overload relays and timing circuit breakers. Manuallyoperated units work separately when testing simple relaysor interconnected to provide four simultaneous outputs for more complex relays. The SR98 offers a lightweight, field portable test set capable of testing a wide range ofelectro-mechanical solid-state and microprocessor-basedprotective relays.

PCITS2000/2

DDA1600

SR98

AVTS is a registered trademark of Megger Group Limited and/or its subsidiaries.

8 Cable fault location equipment Cable fault location equipment 9

Cable fault location equipment

Outputs Surge impulseModel d.c. Burn Surge EnergyPFL1000 0 - 20kV 0 - 60mA 0 - 16kV 1536 J 12µFPFL4000 0 - 20kV 0 - 60mA 0 - 16kV 1536 J 12µFPFL5000 0 - 20kV 0 - 60mA 0 - 16kV 1536 J 12µF

TDR1000/2

TDR2000/2P

L1070

PFL4000

DARTCable fault analysis system

The DART® cable fault analysis system is a microprocessor controlled TDR designed to identify andlocate faults in power cables, using standard pulse echo, arc reflection, differential arc reflection and impulse current methods of prelocation.

The unit being menu driven is easy to use, and allowsoperators to quickly identify and locate faults accurately and effectively.

PFL1000, PFL4000 and PFL5000Power fault locator systems

A series of cost-effective mobile systems dedicated toidentifying, and finding faults in copper cables, accurately,and efficiently.

Each model combines a d.c. test facility, proof/burn mode,surge pulse (impulse current), arc reflection, and pulse echoin a compact field portable module (dependent on modelordered).

DETEX

Surge impulse generatorsSurge generators are used to generate a flashover at the point of fault that can be detectedby an acoustic receiver; this is the preferred method to pinpoint faults in power copper cables.

Megger has a series of surge generators suitable for various cable rating.

SD3000/2Acoustic/Electromagnetic surge detector

The SD3000 is a dual standard acoustic/electromagnetic receiver used to pinpoint the location of flashovers, generated at the point of fault by a surge generator. By incorporating a second detector (Model SD3002) the direction and distance to the fault is displayed.

Earth fault locators BGFT and BGL

See page 15

Surge impulse generatorsSurge impulse H.V. output

Model Output Energy d.c. test Burn651404 Suitcase 0 - 15kV 300 joules, 2.5µF - -651017 Portable 0 - 15kV 536 joules, 5µF 0 - 25kV 0 - 30mA651016 Dual-voltage 0 - 7.5kV 450 joules, 4µF 0 - 25kV 0 - 30mA

0 - 15kV 450 joules, 16µF 0 - 25kV 0 - 30mA651028 Standard 0 - 25kV 1250 joules, 4µF 0 - 30kV 0 - 50mA653031 Heavy Duty 0 - 25kV 3750 joules, 12µF 0 - 65kV 0 - 100mA

0 - 30kV 5400 joules, 12µF 0 - 65kV 0 - 100mA653031-32 Heavy Duty 0 - 25kV 7500 joules, 24µF 0 - 65kV 0 - 100mA

0 - 30kV 10800 joules, 24µF 0 - 65kV 0 - 100mA

Megger TDR1000/2Single channel cable fault locator

A state of the art TDR capable of identifying and locatingfaults on metallic cables. The TDR1000 is suitable for use on both dead or live cables without a blocking filter, up toCATIII 300 V phase-to-earth.

Megger TDR2000/2PDual channel cable fault locator

A state of the art mono or colour display two-channel TDR.capable of identifying and locating faults on metallic cables.The TDR2000P is suitable for use on dead or live cableswithout a blocking filter, up to CATIII 300 V phase-to-earthwith a range of up to 20 km. The TDR has an internalmemory and the TraceMaster software supplied allowsstorage and analysis of waveforms on a PC.

L1050, L1070, L1071 Accutrace,and Cable Route TracerPortable cable locators

These instruments are used to locate the exact route anddepth of metallic cables. The instruments capabilities areenhanced by offering both passive and active modes. Forease of use, and improved efficiency, the instruments can be either inductive or conductively coupled.

Multiple output frequencies* Variable tx output power level* Peak & null detection* Push button depth measurement* (* dependent on model)

DETEX®

Voltage detectors and phasing testers

The DETEX range of testers is ideal for determining thepresence of voltage be it phase to earth or phase to phase.A verification unit is available to ensure safe operation.

Voltage detectors are suitable for voltages from 2.3kV to550kV. Models available with electronic LED and audibleindication or neon indication.

Phasing testers are available from 2.4kV to 69kV with achoice of analogue or neon voltage indication.

DART

SD3000

DART is a registered trademark of Megger Group Limited and/or its subsidiaries. DETEX is a registered trademark of Société Anonyme des Etablissements CATU.

Transformer testing 1110 Transformer testing

Transformer testingWindings

Transformer testingModel TTR550503 TTR100 TTR25 TTR550005Turns ratio range 0.8 to 45,000 0.8 to 20,000 0.8 to 20,000 0.001 to 129.999Excitation voltage 8V, 40V and 80V 8V 8V 8VExcitation current range 0 to 500mA 0 to 100mA 0 to 100mA 0 to 1AOperation Automatic Automatic Automatic ManualPower source Mains Rechargeable batteries Batteries Hand-crankedWeight 7.5kg 1.5kg 1.5kg 7.3kg

TTR550503Three-phase transformer turns ratio test set

Measures three phases simultaneously, the turns ratio ofpower, instrument and distribution transformers. With aturns ratio range up to 45,000:1 and a 0.1% accuracy onlyweighing 7.5kg, the TTR is ideal for testing complex three-phase substation power transformers quickly and accurately,minimizing the possibility of errors. The performance of theTTR has been further enhanced by improved softwareallowing improved reporting and remote control from a PC or laptop.

Megger TTR100Hand-held transformer tester

Fully three-phase capable, the TTR100 is the low costsolution for three-phase transformer testing. The lightestand most portable TTR test set available, it offers a full setof tests including; transformer turns ratio, excitationcurrent, phase angle deviation, winding resistance andtransformer polarity the results of which can be stored onboard for later downloading.

Megger TTR25 NEWHand-held TTR

The Megger TTR25 is an automatic hand-held transformerratio test set used to measure the turns ratio, excitationcurrent and polarity of windings distribution and powertransformers, potential and current transformers, andtapped transformers.

COMLinkCommunications interface software

The COMLink program provides a communications interfacefor transferring data from three phase TTRs and hand-heldTTR100s, as well as BITEs, and DARTs to a PC. It allowsremote control operation of Three Phase TTRs, and for allinstruments the viewing of test data, creation of test datadatabases and printing out of test reports.

TTR550005Single-phase transformer turns ratio test set

The single-phase TTR measures power and distributiontransformers using the manual balancing method. A handcrank provides the power for the TTR550005.

Transformer ohmmeterTransformer winding resistance and tap-change test set

Field portable low resistance measuring instrument designed to test transformer windings, motors, generators and tap changers. The two independentmeasuring channels greatly reduce the test duration of large inductive loads like transmission transformers,where it is possible to measure secondary and primarywindings simultaneously.

Megger MCTT10 NEWCurrent transformer tester

The MCTT10 test set is a portable unit for performingsaturation and ratio tests on current transformers usingthe voltage-comparison method. It provides a variablevoltage output and precision instrumentation for testingsingle and multi-ratio CTs. All tests, saturation and ratio –can be performed without changing any leads. Currenttransformers can be tested in their equipmentconfiguration, such as being mounted in transformers,oil circuit breakers or switchgear. It is, however necessaryfor the equipment to be totally isolated from the electricalsystem prior to testing.

Polarity testerTransformer polarity verifier

This simple device can help avoid an expensive mistake. Its small size and reliable construction make it a usefuladdition to any tool box.

Phase sequence and continuityindicatorProviding positive indication of phase sequence onenergized lines and which phase, if any, is faulty.

Motor and phase rotation testerA compact, rugged and portable instrument suitable forphase sequence and motor ratio testing. Suitable fordetermining the rotation direction of 1, 2 or 3-phasemotors, rotation or sequence of energized power circuits.Can also be used to determine the polarity of instrumentsand power transformers, and phase/polarity of unmarkedmotor windings.

MCTT10

TTR550503

TTR550005

Motor and phase rotationtester

TTR100

TTR25

Transformer ohmmeter

12 Transformer testing Watthour meter testing 13

Dielectric strength testing

Megger OTSAF/2Auto testing seriesA series of fully featured laboratory instruments which haveworld-wide test specifications pre-programmed for ease ofuse. A custom test facility enables the operator to vary theparameters of the tests. Variants offer maximum testvoltages of 60kV, 80kV and 100kV.

Megger VCM100Calibration meterVerifies the calibration of all AF/2 laboratory models of oiltest sets.

Megger OTS60PBPortable automatic testingThe smallest lightest fully automatic portable oil test setavailable with test voltage up to 60kV. Internal rechargeablebattery for operation in remote locations. Optional printerand fully programmed international test sequences.

Megger OTS60SXManual testingLightweight semi-automatic 60kV oil dielectric strength test set which is simple to use and can be powered from a range of mains supplies.

Transformer insulating oil dielectric strength testingModel OTS100AF/2 OTS80AF/2 OTS60AF/2 OTS60PB OTS60SXTest voltage 100kV 80kV 60 kV 60kV 60kVFunction Automatic Automatic Automatic Automatic Semi-automaticPower supply Mains Mains Mains Rechargeable battery mainsWeight 40kg 40kg 40 kg 19kg 17.5kg

Watthour meter testing

PHAZER®

Watthour meter test system

The PHAZER family of watthour meter test sets are true

three-phase, fully automatic systems capable of testing

virtually all types of ANSI socket- mounted and bottom-

connected single- and three-phase (three and four wire)

electricity meters.

The PHAZER family consists of specific models for testing

socket-mounted meters and specific models for testing

panel-mounted and bottom-connected meters. Offering

state of the art optical sensing and a built-in automatic

calibration routine.

MA10

Portable watthour meter standards

The MA10 watthour standards are totally autoranging on

the potential input, current input and auxiliary power input.

The three summing current inputs can be used to perform

closed link testing. Models with VARhour and Qhour

capabilities are available for testing multi-function solid

state meters.

Switches and test blocks

STATES® switches

Test switches

Covers the complete area of panel connections from

terminal block to knife switches. All products give long term

connection quality and mechanical stability.

PHAZER

STATES switches

OTSAF/2

OTS60PB

Transformer insulating oil testingMoisture in oil testing

Megger KF875Portable moisture in insulating oil test setEasy to use, portable one button test set with integralprinter. Can be powered from mains, internal rechargeable battery or car battery. It is ideal for on site use.

Megger KF-UNIPortable variable specific gravity moisture inoil test setEasy to use test set that titrates for specific gravitiesbetween 0.60 and 1.40. It is portable with integral printer.Can be powered from mains, internal rechargeable batteryor car battery. It is ideal for on site use.

Megger KF-LAB NEWVariable specific gravity moisture in oil test setEasy to use test set that titrates for specific gravitiesbetween 0.60 and 1.40. Designed specifically for laboratoryuse the KF-LAB is mains powered only.

KF-LAB

KF875

For sale outside the EU only

PHAZER and STATES are registered trademarks of Megger Group Limited and/or its subsidiaries.

Battery testing 1514 Battery testing

Battery testing Routine impedance testing of batteries is fast and rigorous and insures against the cost of power breakdown.

Megger BITE® 3 NEW

Battery impedance test equipment

The Megger BITE3 battery impedance test equipment

determines the health of lead-acid cells up to 2000Ah by

taking measurements of the most important battery

parameters, cell impedance, an internal ohmic test, cell

voltage, intercell connection resistance and ripple current.

For the first time in a battery test instrument, the BITE3

measures float current and the harmonic content of the

ripple current. There is even a built-in spectrum analyser

to show the harmonic content of the ripple current. It has

firmware that can be upgraded through the Internet and

supports multiple languages.

PROACTIV NEW

Battery database management software

ProActiv is a powerful yet easy-to-use battery database

management software designed to aid the analysis and

monitoring of each individual battery in a battery system.

Failure of a battery system within environments such as

utilities, hospitals or manufacturing plants can result in

operational failure of the devices connected to it.

ProActiv assists the user to avoid battery failures, budget for

future battery string and cell replacements, and plan battery

change-outs in an orderly manner. It utilizes a standard

Microsoft® Access® database format allowing the user to

organize and manage battery data such as voltages,

impedance, intercell connection resistance, ripple current,

specific gravity, and IR thermographs.

BGFT

BITE2P

For sale outside the EU only

Battery testingModel BITE3 BITE2PFor batteries of capacity 2000Ah 7000 Ahd.c. voltage range 0 - 30V 0 - 25Vd.c. voltage resolution 1mV 1mVImpedance range 0 - 100mΩ 0 - 100mΩ

Impedance resolution 1µΩ 1µΩWeight 2.6kg 14.5kg

BITE2P

Impedance tester for up to 7000Ah cells

A rugged durable instrument whose enhanced capabilities

make it easier to determine the true state of health of a

battery system, terminal plate to terminal plate.

The BITE2P is ideal battery systems up to 7000Ah, used in

substations, generating stations, telephone exchange UPS

systems and cabinetised UPS batteries, railway substations,

signal and communications installations.

BGFT

Battery ground fault tracer

Manually balanced instrument that identifies, tracks and

locates ground faults in unearthed d.c. battery systems

on-line. Effective in high electrical noise environments, as

the strength of test current can be adjusted. Useful for

industries where power supply for operating measurement,

communication and control equipment is critical.

BGL

Battery earth fault trace

This instrument detects, tracks and locates earth faults

on battery or floating systems by injecting a 21 or 25Hz

signal (depending on line frequency) between the system

and earth. The resulting current is then traced through

the system with a clamp accessory, knowing that the

fault current will flow to earth until the fault is located.

Designed for operation on live battery systems, hence

there is no requirement to isolate the system.

BITE3

BGLPROACTIV test screens

BITE is a registered trademark of Megger Group Limited and/or its subsidiaries. Microsoft and Access are registered trademarks of the Microsoft Corporation and/or its subsidiaries.

Earth resistance testing 1716 Earth resistance testing

Earth resistance testing

Megger DET2/2High resolution earth tester

High resolution to 1mΩ. This level is required to measureresistivity to adequate depth on many substation andcommunication sites. Measurement of the low earth valuesrequired on many installations, to meet Ground PotentialRise (GPR) requirements also, requires this resolution toensure valid results. Superior noise filtering greater than 40Vpeak to peak to retain resolution under real test conditions.

Megger DET3/2Hand-cranked earth tester

The DET3/2 gives complete independence from batteries ormains power, with its hand-cranked generator. Checks forexcessive spike resistance or noise.

Megger DET5/4D and Megger DET5/4RFour terminal earth tester

With standard resolution to 10mΩ the DET5/4 instrumentsare used for medium sized earths and can also carry outresistivity testing. Simplicity of operation through autoranging and auto-error detection.

Megger DET4TD NEWFour, three and two terminal earth tester

Simple to operate due to one button operation, auto-ranging and auto-error detection, the DET4TD isweatherproof and supplied complete with a lead and stake kit.

Earth resistance testingModel DET2/2 DET3/2 DET5/4D DET5/4R DET4TD DET3TC DET3TD DET3TAMaximum earth resistance ranges 2 kΩ

20 kΩ

Resolution 0.001 Ω 0.01 Ω 0.01 Ω 0.01 Ω 0.01 Ω 0.01 Ω 0.01 Ω 2.5% ofscale

lengthAuto ranging

Pole test Two

Three

Four

Current measurement and ART

Total service accuracy ±0.5% ±2% ±2% ±2% ±2% ±2% ±2% ±2%Display 31⁄2 Digits N/ATest Frequency in Hz 105 to 160 128 128 128 128 128 128 128

Voltage 50 50 50 50 25 or 50 25 or 50 25 or 50 25 or 50 Current in mA 50 10, 1 or 0.1 10, 1 or 0.1 10, 1 or 0.1 0.45 or 4.5 0.45 or 4.5 0.45 or 4.5 0.45 or 4.5

Potential circuit rejection (pk-pk) 40 V 20 V 40 V 40 V 40 V 40 V 40 V 40 VMax current loop resistance 2 kΩ range 5 kΩ 10 kΩ 4 kΩ 4 kΩ 100 kΩ 100 kΩ 100 kΩ 100 kΩ

20 kΩ range >20 kΩ 100 kΩ 400 kΩ 400 kΩPower source Rechargeable battery

Dry Cell battery

Hand-crank

Weather proof IP54

Calibration certificate in the box

DET2/2

DET3/2

DET3TC

DET4TD

Megger DET3TD and DET3TANEWThree and two terminal earth tester

Ideal for small earthing systems, earth rods and lightningconductors the DET3T gives you the choice of digital oranalogue displays, offering simple one button operationwith auto-ranging from 10mΩ to 2kΩ. Supplied completewith test kit and carry case.

Megger DET3TC NEWThree and two terminal earth tester withAttached Rod Technology (ART)

Offering all the benefits of the DET3TD but offering theoption of selective, no-disconnect testing and earth leakagetesting using a clamp. Supplied complete with test kit andcarry case (clamp optional).

All Megger earth testers are weather proofed to IP54for field use.

Megger DCM300E Earth leakage clamp

Measurement of leakage current. For stable readings downto very low current value with a 10 mA resolution. Currentmeasurement up to 300A.

Megger DET10C and MeggerDET20C Earth resistance clamp testers

Earth resistance clamp meters are suitable for measuringearth resistance installations such as buildings, distributionpole and RF transmitter sites and for inspection of lightningprotection systems. The DET20C offers memory anddownloading capability.

Earth resistance testingModel DET10C DET20CEarth resistance ranges auto ranging 0.025Ω to 1550Ω

Alarm High 0 to 1550 ohms

Low 0 to 1550 ohms

Leakage current ranges 0.200 mA to 1.00 A

1.00 A to 35 A

Auto ranging

Datalogging capacity 116 records 8180 recordsData download

DET20C

Low resistance measurement 1918 Low resistance measurement

Low resistance measurementComprehensive range of low resistance ohmmeters suitable for all power and battery applications.

Megger DLRO600600A low resistance ohmmeter

Provides the operator with high resolution, 0.1µΩ,lightweight and portable method of performing on-site lowresistance measurements. The unit can be used to test circuitbreaker contact resistance to IEC 62271-100, switch contacts,busbars, joints, splices, fuses and rail bonds. The test currentis variable from 10A to 600A, in 1A steps, enabling the userto perform all the required test with a single instrument.

Megger DLRO200200A low resistance ohmmeter

Provides the operator with high resolution, 0.1µΩ,lightweight and portable method of performing on-site lowresistance measurements. The test current is variable from10A to 200A, in 1A steps, enabling the user to perform allthe required test with a single instrument. The unit can beused to test small circuit breaker contact resistance to IEC62271-100, switch contacts, busbars, joints, splices, fuses andrail bonds.

Megger DLRO10X10A low resistance ohmmeter with testresults downloading

The DLRO10X offers a 0.1µΩ resolution with a maximumcapability of 2kΩ. Fast testing ability means users canachieve results in less than 3 seconds. At only 2.5kg it is thesmallest, lightest and most sophisticated 10A low resistanceohmmeter available.

The DLRO10X has the capability of measuring inductiveloads such as transformers and motor winding. Availabilityof readings can vary from a few seconds up to minutesdepending on the inductance and resistance of the test item.

The DLRO10X adds on-board memory, RS232 downloadcapability, maximum setting and manual or automatic rangecontrol to the features of the DLRO10.

Low resistance measurementModel DLRO600 DLRO200 DLRO10X DLRO10 BT51Measurement ranges 1.9999mΩ 1.9999mΩ 20.00mΩ

19.999mΩ 19.999mΩ 2000mΩ199.99mΩ 199.99mΩ

0.1µΩ to 999.9mΩ 0.1µΩ to 999.9mΩ 1.9999Ω 1.9999Ωauto ranging auto ranging

19.999Ω 19.999Ω199.99Ω 199.99Ω1999.9Ω 1999.9Ω

Resolution 0.1µΩ 0.1µΩ 0.1µΩ 0.1µΩ 10µΩAccuracy <1% <1% ±0.2% ±0.2% ±1%Current test range 10A - 600A 10A - 200A 0.1mA - 10A 0.1mA - 10A 2.0AResults storage 300 300 700RS232

Power source Mains

Rechargeable battery

Weight excluding leads 14.5kg 14.5kg 2.6kg 2.6kg 4.5kg

DLRO600

Megger DLRO® 1010A low resistance ohmmeter

The DLRO10 offers a 0.1µΩ resolution with a maximumcapability of 2kΩ. Fast testing ability means users canachieve results in less than 3 seconds. At only 2.5kg they arethe smallest, lightest and simplest-to-use 10A low resistanceohmmeter available.

BT512A low resistance ohmmeter

Low resistance ohmmeter ideally suited for bond testingapplications, i.e. aircraft frames, electronic discharge andfuel tanks. Four terminal method of measurement ranges 0-20.00mΩ and 0-2000mΩ. High test current of 2A.

Clips and leads for low resistance testingMegger ohmmeters require test leads, two potential (voltage) and two current, to make low-resistance measurements. In addition to individual current and potential (voltage) leads sets, duplex leads that combine current and potentialconnections in one lead are offered. A variety of terminations, C-clamps, Kelvin clips, fixed point, and helical spring-pointleads are available.

Battery testingMaximum

For measurement of Lead type Termination test current Length Reference noPotential Single 2 pieces Hand spike N/A 2.0m 242021-7

5.5m 242021-189.0m 242021-30

Current Single 2 pieces Current clip 10A 2.0m 242041-75.5m 242041-189.0m 242041-30

Single 1 piece Heavy duty C-clamps 10A 5.0m 242144-168.0m 242144-26

Current and potential Duplex 1 piece DH2 handspike with helical sprung contacts 10A 6.0m 6111-023Current and potential Duplex 1 piece DH3 handspike with helical sprung contacts 10A 9.0m 6111-024Current and potential Duplex Lead set DH1 handspikes with helical sprung contacts 10A 2.5m 6111-022Current and potential Duplex Lead set DH4 handspikes one with indicator light 10A 1.2m 6111-503Current and potential Duplex Lead set DH5 handspikes one with indicator light 10A 2.5m 6111-517Current and potential Duplex Lead set DH6 handspikes one with indicator light (600V) 10A 1.2m 6111-022Current and potential Duplex Lead set 1.3cm silver-plated Kelvin clip 10A 2.0m 241005-7Current and potential Duplex Lead set 4.0cm silver-plated Kelvin clip 10A 2.0m 242006-7

5.5m 242006-189.0m 242006-30

Current and potential Duplex Lead set Hand spikes with helical spring-loaded contacts 10A 2.0m 242011-75.5m 242011-169.0m 242011-30

Current and potential Duplex Lead set Helical hand spikes with spring points and 10A 5.5m 242009-18current push button switch

Current and potential Duplex Lead set Heavy duty straight fixed contacts 10A 2.0m 242002-75.5m 242002-189.0m 242002-30

Current and potential Duplex Lead set Heavy duty 5cm C-clamps 10A 2.0m 242004-75.5m 242004-189.0m 242004-30

Current and potential Duplex Lead set Hand spikes with replaceable needle points 10A 2.0m 242003-7Current and potential Duplex Lead set Heavy duty 10cm C-clamps 100A 5.0m 242004-2-16

8.0m 242004-2-26Current and potential Single Lead set Heavy duty 10cm C-clamps 100A 5.0m 242004-2-16Current potential Duplex Lead set 2 x current leads with 7.6cm clamps 100A 10.0m 830255

2 potential leads with 2.5cm battery clips N/A 10.0mCurrent potential Duplex Lead set 2 x current leads with 4.5cm clamps 100A 15.0m 830258

2 potential leads with 2.5cm battery clips N/A 15.0mCurrent potential Duplex Lead set 2 x 25mm2 current leads with clamps 600A 5.0m 6220-787

2 potential leads with clips N/A 5.0mCurrent potential Duplex Lead set 2 x 50mm2 current leads with clamps 600A 5.0m 6220-755

2 potential leads with clips N/A 5.0mCurrent potential Duplex Lead set 2 x 70mm2 current leads with clamps 600A 10.0m 6220-756

2 potential leads with clips N/A 10.0mCurrent potential Duplex Lead set 2 x 95mm2 current leads with clamps 600A 15.0m 6220-757

2 potential leads with clips N/A 15.0mDLRO10X

DLRO10

BT51

DLRO200

DLRO is a registered trademark of Megger Group Limited and/or its subsidiaries.

20 Power Quality

Power quality

Megger PA9plusPower quality analyserThe PA9plus has enhanced standard key features including a fast digital signal processor to support future evolvingfeatures and capabilities, a full 12MB of internal, non-volatile memory and incorporated auxiliary power inputcapabilities.

The product offers testing to the relevant standards(EN50160, IEC61000 series, IEEE1159, IEEE519).

Data can be downloaded from the PA9 without interruptingthe capability of instrument to record events. The optionalremovable memory capabilities allows internal recordeddata to be copied directly to an external standard compactflash card using the same technology available with most oftoday’s digital cameras. This means that without a computeron site, data can be copied, manually or unattended, fromthe instrument to external memory cards, increasing theeffective instrument memory storage to the size of thememory card used, and will program new configurationsetups in the same, simple manner.

Megger MetReportPower quality analysis softwareMetReport is an extremely powerful, fully functional, andstand-alone report generation tool for the Megger PA-9Pluspower quality analysers. Its primary purpose is todramatically improve and extend the reporting capabilitiesof our complimentary software packages.

In today’s economy, time is money. Power and power qualityprofessionals currently spend countless hours every yearcreating customized reports supporting their analysisstudies. MetReport automates this tedious task whileimproving the accuracy and reliability of the entirereporting process.

MetReport utilizes data files obtained from the PA-9 andPA-9Plus to rapidly produce completely customizable reportstargeted to your particular applications and requirements.Some examples include: Power quality studies, harmonicsanalysis, power factor and energy consultation, tolerancecurve studies (CBEMA/ITIC, SEMI F47, User Defined), autodata analysis pass/fail reports, EN50160 compliance, andIEEE/IEC Flicker. The key to quickly learning and usingMetReport is the integrated wizard function. This wizardeffortlessly takes you through the entire report creation,customization, and generation process. Several samplereport templates are included for review, and may bemodified to meet your specific needs.

All reports are output as standard Microsoft Worddocuments.

Megger SLM8

8 channel recording volt-ammeterThe SLM8 is a low cost, 8 channel paperless recording volt-ammeter used for measuring and recording the true RMSvalues of up to four voltage channels and four currentchannels. It is the ideal investigative tool for utility trouble-shooters, service investigation groups, meter shop technicians and facility managers to identify anddocument the presence of tree-phase and single-phasevoltage complaints utilizing associated load currentinformation to locate the source of problems.

Title Name

Job title

Company

Address

E-mail

Telephone

Fax

PA9plus

Megger MetReport screens

SLM8 For sale outside the EU only

Megger DCM1000P andDCM2000PRelay clampmeter

These advanced clampmeters are particularly suited toprotection testing, due to its power frequency and true RMS measuring capabilities. For both single and three phase systems. The DCM2000P also offers the functionalityof power meter, oscilloscope, harmonics meter and datalogger in one easy-to-use instrument.

PMM13 phase power measurement meter

Capable of measuring a.c. / d.c. voltage, a.c. primary andsecondary current, power, power factor, reactive power,phase angle and frequency of single and three phaseelectrical systems with extreme accuracy. Integral solid statetime suitable for continuity and voltage sensing andharmonic measurement up to 49th harmonic. For detailedwaveform analysis a high-speed capture function allow 20measurements per second. An RS232 data port allows bi-directional communication.

Model 8 Mark7Analogue multimeter

The multimeter that has become the industry standard, due to its robust construction.

DCM2000P

PMM1

Model 8 Mark7

For more information on Megger products

fill in your details on this card and return it

to us in Dover.

Please send me the Megger Product

Catalogue on CD

Please send me more information on the

following

Megger Pty LimitedUnit 26 9 Hudson AvenueCastle HillSYDNEY NSW 2125AUSTRALIA

T +61 (0)2 9659 2005F +61 (0)2 9659 2201E ausales@megger.com

MeggerPO Box 15777Kingdom of BAHRAIN

T +973 17 411311F +973 17 413399E mesales@megger.com

Megger Limited110 Milner Avenue Unit 1Scarborough Ontario M1S 3R2CANADA

T 1 800 297 9688 (Canada only)T +1 416 298 6770F +1 416 298 0848E casales@megger.com

Megger SARL23 rue Eugène Henaff ZA du Buisson de la Couldre78190 TRAPPESFRANCE

T +33 (0)1 30 16 08 90F +33 (0)1 34 61 23 77E infos@megger.com

MeggerPO Box 12052Mumbai 400 053INDIA

T +91 22 26315114F +91 22 26328004E insales@megger.com

Megger LimitedArchcliffe Road DoverCT17 9ENUK

T +44 (0) 1304 502100F +44 (0) 1304 207342E uksales@megger.com

Megger4271 Bronze WayDallas, TX 75237-1019 USA

T 1 800 723 2861 (USA only)T +1 214 333 3201F +1 214 331 7399E ussales@megger.com

MeggerValley Forge Corporate Center2621 Van Buren AvenueNorristown PA 19403 USA

T 1 800 723 2861 (USA only)E ussales@megger.com C

op

yrig

ht

© 2

005

Meg

ger

. Pri

nte

d in

th

e U

K B

P/12

K/0

805

2 Ed

. Par

t N

o 2

1500

-051

The products featured in this catalogue are available from:

For comprehensive technical information on the entire Megger product range, visit:

www.megger.com

Megger Limited

Archcliffe Road,

Dover,

CT17 9EN,

England

Product information, photographs and illustrations in this catalogue were current whenapproved for print. In a continuing effort to offer innovative products, Megger Limited reservesthe right to change specifications, designs, models and prices without prior notice. Megger is a Registered Trade Mark of Megger Limited.

WW

W.M

EG

GER

.CO

M