(2x) BoltedEyehooks

Net &Net Rope

NetTightener

TopPulley

MODEL #2201-11

NetTightener

SidePulley

Net &Net Rope

MODEL #2201-20

(2x) BoltedEyehooks

MODEL #2201-113-1/2" O.D. GALVANIZED COMPETITION POST (118 lbs)

- WITH TOP PULLEY OPTION-

TENNIS

MODEL #2201-203-1/2" O.D. GALVANIZED COMPETITION POST (120 lbs)

-WITH SIDE PULLEY OPTION-

GENERAL: Tennis posts are available with fixed eyes, net tightener, and side pulley or top pulley- depending on model selected. All models consist of a pair of posts, except center posts which are designed for side-by-side courts, & include only one post. All posts are equipped w/ fittings for proper net attachment. NOTE: See page 3 for included accessories.

MATERIAL: All materials are selected for strength, durability and the abilty to withstand years of exposure.

POSTS: A 3-1/2" O.D. heavy-duty galvanized steel post. All posts are fabricated from galvanized steel pipe. Overall length of all posts is 5'10" allowing for 24" of post to be buried in concrete. NOTE: Post with top pulley is 3" shorter than its mating post to allow for proper net height.

ROPE CLAMPS: A heavy-duty self-securing clamp, die-cast from rustproof "zamak" metal. Designed to take rope sizes 1/8" to 3/8". Designed to take stress off of rope, as it has a smoothe grooved track for the rope. NOTE: For use on nets with rope suspension.

NET TIGHTENER W/ REMOVABLE HANDLE: Permits easy and accurate tensioning of the net. Designed for use on nets with cable or rope suspension. Aluminum cast with a removable handle to lock in place. Pull pin and remove handle.

SIDE PULLEY: All welded construction of heavy gauge steel galvanized or powder coated. A 2-1/2" Dia. pulley on a 3/8" diameter shaft guides the net cable or rope to the tightener.

FIXED EYES: 3/8" diameter zinc-plated steel eyebolts for all models. Heavy steel eyebolts for center post double eyes. These fixed eyes are welded on square post models.

EYE NUT: 3/8" eye nuts have internal threads and are used for extending eyebolt for double sided eyes on center posts. Zinc finish.

FINISH: All welds are ground smooth: cold galvanized compound (or) prepared for powder coat.

WARRANTY PERIOD: 10 years

SPECIFICATION/INSTALLATION INSTRUCTIONSCOMPETITION TENNIS POST W/ NET

TIGHTENER, SIDE PULLEY & ROPE CLAMPMODEL NO.

2201-11 & 2201-20

Date: 4/20/15

Drawn: MT

Sheet: 1 of 5

Rev: 7/13/17

Formula to calculate total depth of footing:24" (Std) + X (Extension) + 6" = D (Depth) NOTE: For Sand installation, add depth of sand to total.

SPECIFICATION/INSTALLATION INSTRUCTIONSCOMPETITION TENNIS POST W/ NET

TIGHTENER, SIDE PULLEY & ROPE CLAMPMODEL NO.

2201-11 & 2201-20

Date: 4/20/15

Drawn: MT

Sheet: 2 of 5

Rev: 7/13/17

Black Nylon for Post

PULLEY & CABLE

White Nylon for Post

SPECIFICATION/INSTALLATION INSTRUCTIONSCOMPETITION TENNIS POST W/ NET

TIGHTENER, SIDE PULLEY & ROPE CLAMPMODEL NO.

2201-11 & 2201-20

Date: 4/20/15

Drawn: MT

Sheet: 3 of 5

Rev: 7/13/17

SPECIFICATION/INSTALLATION INSTRUCTIONSCOMPETITION TENNIS POST W/ NET

TIGHTENER, SIDE PULLEY & ROPE CLAMPMODEL NO.

2201-11 & 2201-20

Date: 4/20/15

Drawn: MT

Sheet: 4 of 5

Rev: 7/13/17

Net Tightener Collar(Top View)

TENNIS INSTALLATION INSTRUCTIONS:

1. Dig holes per footing detail.2. Install eyebolts onto posts. Note: Cut & peen any excess threads out of nut.3. Attach Net Tightener to collar with 5/16" x 3/4" Hex Bolt.4. Slide the net tightener over the post with one eyebolt and secure with setscrew.

NOTE: For Model 2201-11, Post to accommodate top pulley is 3" shorter than the opposite postto allow for proper net height. For Model 2201-20, secure the side pulley 3" from the top with setscrew.

5. Secure fittings in place with hex wrench.6. Set the double eye post in a hole and shim from below so that the top eye is 42" above finish grade.7. Set the post with the top pulley (Model 2201-11) and shim from below so that the top of the pulley is 42"

above finish grade. Set the post with the side pulley in a hole and shim from below so that the top of the post is 45" above finish grade. Plumb and Brace.

8. Pour concrete up to within 2" of finish grade. Let concrete set for 3 days before removing bracing.9. Cover concrete footings with turf or court materials.

NOTE: Footing sizes are based on average soil conditions. Loose and/or sandy soil is not average & footing sizes must be increased accordingly to meet local soil conditions.

Pulley Top CapNet Tightener Collar

Pulley Collar

2201-20 QtyNet Tightener Handle 12-7/8" Net Tightener Collar 15/16 x 3/4" Hex Bolt for Above 25/16" Flat Washer for Above 22-7/8" Side Pulley Collar 12-1/2" Cast Pulley 13/8" x 2" Eye Bolt 13/8" x 1" Eye Bolt 33/8" Nylock Nut for Side Pulley 11/2" x 3/4" Set Screw for Collar 1Rope Clamp - Net Tightener 11/2" Eye Nut - Welded Thread for SP 1Rope Clamp with S-Hook 15/16" x 2-1/2" S-Hook 11/4" Hex Key Wrench 1

2201-11 QtyNet Tightener Handle 12-7/8" Net Tightener Collar 15/16 x 3/4" Hex Bolt for Above 25/16" Flat Washer for Above 22-7/8" Side Pulley Collar 12-1/2" Cast Pulley 13/8" x 2" Eye Bolt 13/8" Nylock Nut for Side Pulley 11/2" x 3/4" Set Screw 23/8" x 1" Eye Bolt 3Rope Clamp with S-Hook 11/4" Hex Key Wrench 1

SPECIFICATION/INSTALLATION INSTRUCTIONSCOMPONENTS

MODEL NO.

2201-11 & 2201-20

Date: 4/20/15

Drawn: MT

Sheet: 5 of 5

Rev: 7/13/17