TEMPINSPECT USB USER GUIDE

COLDCHAINVISION.COM

f - @coldchainvision

• 1 minute

STEP1--,

(��Wf�s�r

r;:�� seconds between

Qresses)

o -'

STEP2--, flash2 times

.._J

Before starting the Tempinspect opera­tion, pressing the multifunction button with 2 quick presses (with less than 2 seconds between presses), the interval between successive tempera­

ture acquisitions is selected for 1 minute, i.e. every 1 minute a tempe­rature acquisition is made and stored in the Tempinspect memory. The Green led will flash 2 times indicating the selection.

• 5 minutes

o

(t�Wf�s�r

;;;�� secondsbetween

pressas)

srEP 2 � 3 1

" 1 ,

STEP1 --,

mes Before starting the Tempinspect opera-tion, pressing the multifunction

.,.__J button with 3 quick presses (with less than 2 seconds between presses), the interval between successive tempera­

ture acquisitions is selected for 5 minutes, i.e. every 5 minutes a temperature acquisition is made and stored in the Tempinspect memory. The Green led will flash 3 times indicating the selection.

• 10 minuteSTEP2

--, Hash4times

.._J

Before starting the Tempinspect opera­tion, pressing the multifunction button with 4 quick presses (with less than 2 seconds between presses), the interval between successive tempera­

ture acquisitions is selected for 1 O minutes, i.e. every 1 O minutes a temperature acquisition is made and stored in the Tempinspect memory. The Green led will flash 4 times indicating the selection.

• 15 minutes

o

(��� f�s� rh:i� seconds between

presses)

STEP2--,

flash5times

.._J

STEP1 --,

i r s Before starting the Tempinspect operation,pressing the multifunction button with5 quick presses ( with less than 2 seconds between presses), the interval between successive temperature

acquisitions is selected for 15 minutes, i.e. every 15 minutes a tempe­rature acquisition is made and stored in the Tempinspect memory. The Green led will flash 5 times indicating the selection.

• 30 minuteSTEP1

-:--,

(���1f�s�

rr;:��

seconds between pressas)

STEP2--,

flash 6times

.__J

Before starting the Tempinspect operation, pressing the multifunction button with 6 quick presses (with less

than 2 seconds between presses), the interval between successive temperature

acquisitions is selected for 30 minutes, i.e. every 30 minutes a tempe­rature acquisition is made and stored in the Tempinspect memory. The Green led will flash 6 times indicating the selection.

• 1 Hour

STEP 1

o

(�� f�s� ;;;�� se<:onds between

pressas)

-'

STEP2--,

flash 7 times

.._J

--, i r

Before starting the Tempinspect operation, pressing the multifunction button with 7 quick presses (with less than 2 seconds between presses), the interval between successive temperature

acquisitions is selected for 1 hour, i.e. every 1 hour a temperature acquisition is made and stored in the Tempinspect memory. The Green led will flash 7 times indicating the selection.

• 2 Hour

STEP1--,

(�iwr�s�rr�:�� seconds between

presses)

o ._J

srEP 2 � 8 times Before starting the Tempinspect operation,

1 pressing the multifunction button with __....J 8 quick presses (with less than 2

seconds between presses), the interval between successive temperature

acquisitions is selected for 2 hours, i.e. every 2 hours a temperature acquisition is made and stored in the Tempinspect memory. The Green led will flash 8 times indicating the selection.

• 3 HourSTEP1

--,

o

g"fiWf��rte;;��

seconds between pressas)

-'

STEP2--, B fe flash g times Ore Starti

. ng t h e Tempinspect opera t' IOn,1 pressing the multifunction button with

----1 9 quick presses (with less than 2 seconds between presses), the interval between successive temperature

acquisitions is selected for 3 hours, i.e. every 3 hours a temperature acquisition is made and stored in the Tempinspect memory. The Green led will flash 9 times indicating the selection.

• 4 HourSTEP2

--, flash IO times Before starting the Tempinspect operation,

1 pressing the multifunction button with ----1 1 O quick presses (with less than 2

seconds between presses), the interval between successive temperature

acquisitions is selected for 4 hours, i.e. every 4 hours a temperature acquisition is made and stored in the Tempinspect memory. The Green led will flash 1 O times indicating the selection.

• Setting Temperature Range

The Tempinspect USB data logger has 7 temperature range presets. These define the upper and lower temperature limits for the device's temperature range alarm system.

To set the temperature range, press the multifunction as follows: 2 quick presses followed quickly by a 5 second press to set 2°c

to 8°c range (Default) 3 quick presses followed quickly by a 5 second press to set -1 °c

to -10°c range 4 quick presses followed quickly by a 5 second press to set -2°c

to -8°c range 5 quick presses followed quickly by a 5 second press to set 2°c

to 25°c range 6 quick presses followed quickly by a 5 second press to set 15°c

to 25°c range 7 quick presses followed quickly by a 5 second press to set 15°c

to 30°c range 8 quick presses followed quickly by a 5 second press to set -15°c

to -30°C range After selecting the range, immediately press and hold the multifunction button for 5 seconds to confirm your selection. The LED light will blink red as many times as required by your selection to confirm your settings. (Example: 4 red blinks confirm -2°c to -8°C range)

• Start/StopSTEP1

--,

pressfor5 seconds

0 _--.,.....J

STEP2--,

0

press and ho1dfor

Ssaconds

...,J

STEP3--, ,

J operation (temperature

o logging) quickly pressfor 5 seconds and

+ quickly re-press for

another 5 seconds and release the multifunction button. Green and Red leds will flash alternatingly during 5 seconds, indicating that the Temptrail has been initialized. Once started, the device operation can be terminated at any time by repeating the same procedure to start the operation. The operation cannot be reset. The data logger has a 10 minute start delay.

• Check status

At any time, a quick press on multifunction button informs the tempinspect´s state:

Before initiating operation, the tempinspect is IDLE, which is represented by a single flash of the green led, followed by a single flash of the red led.

During operation, the tempinspect is RECORDING, which is represented by four flashes of the green led.

After the operation is terminated, the tempinspect is DONE, which is represented by two flashes of the red led, followed by two flashes of the green led.

• Check alarm

STEP 1

Short press the ..,._Multifunctional

Button

Tempinspect will show the visual alarms via a red or green flashing led light

• by by pressing the status button once. If

the products have been exposed over the chosen temperature range, a red led

light will flash one time for every interval equivalent of exposure time over the chosen temperature range, and if products are exposed under the chosen temperature range, a red led light will double flash for every interval temperature reading equivalent. Therefore if you set the data logger to take temperature with 1 0 minute intervals, the led alarms will give one flash for every ten minutes over the temperature range or double red led Flash for every ten minutes under the Temperature Range. If no out of range exposure the green led will flash four times confirming data logger is recording and no alarms have taken place. The below is an example for a set measurement time every ten minutes. The visual alarms may be seen prior to stopping the data logger by a simple press of the status button. once the data logger is stopped, connect it to your usb drive and a pdf and csv file are automatically generated with all required information.

STEP2 i

STEP3

J

Flash Once

Flash Twi ce Quickly

For every 10 minutes ABOVE the maximum temperature limit, the red led will flash once.

For every 10 minutes BELOW the minimum temperature limit, the red led will flash twice quickly

• Detailed Diagnosis

Get the detailed diagnosis of the temperature at which the cargo has been exposed.

fr"'

" 0 J Remove The Top

The Delay may be customized via our custom software availablefor download on www.coldchainvision.com/software.

To start the Tempinspectled in dic ator

For resetting multi-use data logger press status button 9 times and on tenthtime keep pressed for 5 seconds. Green and red light will do simultaneously a long flash indicating data logger is resetting. Once reset the data logger will give 1 green light and 1 red flash indicatingthat now the logger is ready to be programmed as new.