ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11

TEETH & BLOCKS

D Added asterisk to notes on page 9 & 10. Note pg 11 12-19-11

C Update page 6 table 12-14-11

B Updated various graphics 12-1-11

A Notes updates and cosmetic changes 101911

REV DESC / PAGE NUMBERS AFFECTED DATE

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 2

PART NO. CODE

NO. DESCRIPTION APPLICATION

2429171 TX50 Tooth, dirt, heat treated

Dirt, compacted soils, low abrasion materials, fits all TX– series shank plates & TX-50 replaceable tooth pilot.

2429429 TX52 Tooth, dirt, outside gauge, heat treated

Dirt, compacted soils, low abrasion materials, fits all TX-series shank plates & TX-50 replaceable tooth pilot. Recommended for outside blocks.

A029225 TX56 Tooth, rock, (carbide) conical, four-tip, heat treated

Fractured and non-fractured materials, frozen soils, abrasive materials. Conical tips increase penetration rates in most materials. Fits all TX-series shank plates & TXC50 pilot.

A029400 TX58

Tooth, rock, (carbide) conical, four-tip, outside gauge, heat treated

Fractured and non-fractured materials, frozen soils, abrasive materials, conical tips increase penetration rates in most materials. Fits all TX-series shank plates & TX50C pilot. Recommended for outside blocks.

65342385TU TX58

Tooth, rock, (carbide) chisel, four-tip, outside gauge, heat treated

Non-fractured materials, frozen soils, abrasive materials. Tips increase penetration rates in most materials. Fits all TX-series shank plates & TX50C pilot. Recommended for outside blocks.

65342386TU TX56 Tooth, rock, (carbide) chisel, four-tip, heat treated

Non-fractured materials, frozen soils, abrasive materials. Tips increase penetration rates in most materials. Fits all TX-Series shank plates & TXC50 pilot.

Teeth, Auger, TX Series

PART NO. DESCRIPTION BLOCK PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET 2429171 TOOTH,TX50 shank plates 25 0.93 25.95 11.77 1250 1297.50 588.54

2429429 TOOTH,TX52 shank plates 25 1.15 29.25 13.27 1250 1462.50 663.38

A029225 TOOTH,TX56 shank plates 25 1.10 28.75 13.04 1250 1437.50 652.04

A029400 TOOTH,TX58 shank plates 25 1.20 31.50 14.29 1250 1575.00 714.41

65342385TU TOOTH,TX58 shank plates 25 1.30 27.80 12.61 1250 1390.00 630.49

65342386TU TOOTH,TX56 shank plates 25 1.26 29.15 13.22 1250 1457.50 661.11

RETURN TO TABLE OF CONTENTS

Notes:

1) Full pallet of teeth contains 50 buckets

2) These teeth use rubberlock A001277

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 3

2-1/

2”

1-3

/4”

Teeth & Blocks, Blade Series

PART NO. CODE

NO. DESCRIPTION APPLICATION

2416844 TRT1 3/16” (4.8 mm) THK. Full face rock blade.

Non-fractured material, frozen soil, abrasive material. Medium to hard rock.

A510184 TWT2

3/16” (4.8 mm) THK. Full face gauge rock blade. Tooth cuts 3/4” (19.1 mm) gauge for pocket

Non-fractured material, frozen soil abrasive material. Medium to hard rock.

A029321 TK55C

Four tip conical carbide rock cutter. 3/8” (9.5 mm) THK. Conical brazed and then entire cut is heat treated for strength and durability.

Fractured and non-fractured material. Angle of attack & conical tips increase penetration rates in most augerable materials. Hard to very hard rock.

17318 TDB31 Heat treated dirt blade, with a 45 degree attack angle.

Soft earth digging, and clay materials.

69322 TAP3

ASTM-148 Cast steel tooth block. Tapered slot to reduce tooth chatter.

Accepts all above teeth. Welded with 7018 or 8018 low-hydrogen rod.

PART NO. DESCRIPTION BLOCK PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

2416844 TOOTH,TRT1 69322 25 1.05 27.55 12.50 1250 1377.50 624.82

A510184 TOOTH,TWT2 69322 25 1.10 29.05 13.18 1250 1452.50 658.84

A029321 TOOTH,TK55C 69322 25 1.21 31.75 14.40 1250 1587.50 720.01

17318 TOOTH,TDB31 69322 20 1.45 29.80 13.52 1000 1490.00 675.85

69322 BLOCK 25 1.20 30.25 13.72 1250 1512.50 686.06

Notes:

1) Full pallet of teeth contains 50 buckets

2) These teeth use roll pin 2443223

2-3

/8”

5/8

”

2-7

/8”

1-1

/8”

1-3

/4”

1-3

/4”

1-3

/4”

2-3

/4”

2-1/2”

1-15/16”

1/2

”

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 4

PART NO. CODE NO. DESCRIPTION APPLICATION

A001375 RB1LRSN Heat treated alloy steel body, sharp-nose carbide tip, long retainer

Small diameter tip reduces vibration during concrete cutting.

A001371 RB3LR Heat treated alloy steel body, sharp-nose carbide tip, long retainer

Fractured and non-fractured materials, frozen soils, and abrasive materials.

A001379 RB3SR Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Fractured and non-fractured materials, frozen soils, and abrasive materials.

2429912 RL08/C3LR Heat treated alloy steel body, sharp-nose carbide tip, long retainer

Cutting concrete and other tough cutting applications

2429913 RL09/C3SR94 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For cutting concrete and other tough cutting applications.

2429911 TX1HDSR/

RL10/C1HDSR

Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For drilling concrete and rock cutting. Double-angle tip provides maximum impact strength.

A001376 RB1SR-SN Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Fractured and non-fractured materials, frozen soils, and abrasive materials.

2429941 C10 Heavy duty tooth block; 45° mounting surface

Has a narrower face than C10HD style. Welded with 7018 or 8018 low-hydrogen rod.

29942 C10HD Extra heavy duty block; 45° mounting surface

Extra-heavy-duty design. Welded with 7018 or 8018 low-hydrogen rod.

A001404 RC10F Heavy duty block with mounting surface parallel to tooth axis

For buckets, barrels, and special applications. Welded with 7018 or 8018 low-hydrogen rod.

Teeth & Blocks, Bullet , .76, TC10 Series

PART NO. DESCRIPTION SHANK

SIZE PER

BUCKET LBS EA

LBS / BUCKET

KGS / BUCKET

PCS/ PALLET

LBS / PALLET

KGS / PALLET

A001375 TOOTH,RB1LRSN 0.76 75 0.47 38.95 17.67 3750 1947.50 883.37

A001371 TOOTH,RB3LR 0.76 75 0.45 38.05 17.26 3750 1902.50 862.96

A001379 TOOTH,RB3SR 0.76 75 0.44 35.05 15.90 3750 1752.50 794.92

2429912 TOOTH,RL08/C3LR 0.76 75 0.45 36.75 16.67 3750 1837.50 833.48

2429913 TOOTH,RL09/C3SR94 0.76 75 0.40 34.25 15.54 3750 1710.00 775.64

2429911 TOOTH,TX1HDSR 0.76 75 0.50 37.70 17.10 3750 1885.00 885.02

2429941 BLOCK,C10 0.76 50 1.10 56.50 25.63 2500 2825.00 1281.40

29942 BLOCK,C10HD 0.76 25 1.19 29.00 13.15 1250 1450.00 657.71

A001404 BLOCK,RC10F 0.76 50 0.71 36.95 16.76 2500 1847.50 838.02

A001376 TOOTH,RB1SR-SN 0.76 75 0.45 36.70 16.65 3750 1835.00 832.34

Note: Full pallet of teeth contains 50 buckets RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 5

PART NO. CODE NO. DESCRIPTION APPLICATION

2429897 C21 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For most cutting applications. Especially good in soft to medium-hard material. Carbide tip (5/16” dia.) for

2429898 C21HD Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Heavy duty design for extremely hard rock and concrete. Carbide tip (1/2” dia.) provides long tool life.

2429900 C23 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Drilling and core-barreling in soft to medium-hard rock with abrasive cutting conditions.

65340029 C23 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Drilling and core-barreling in soft to medium-hard rock with abrasive cutting conditions.

2429901 C24 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Drilling soft material. Sharp nose tip for high penetration.

A001378 RB21SN Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Sharp nose provides fast penetration.

A001373 RB23 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

Soft to medium-hard rock with abrasive conditions.

2429939 C20HD Extra heavy duty block; 45° mounting surface

Heavier block design than the C20 block. Welded with 7018 or 8018 low-hydrogen rod.

2429938 RC20 Heavy duty block; 45° mounting surface

Thinner width allows closer block placement in restricted areas. Welded with 7018 or 8018 low-hydrogen rod.

Teeth & Blocks, Bullet, .74, TC20 Series

PART NO. DESCRIPTION SHANK

SIZE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

2429897 TOOTH,C21 0.74 75 0.39 29.65 13.45 3750 1482.50 672.45

2429898 TOOTH,C21HD 0.74 75 0.49 38.70 17.55 3750 1935.00 877.70

2429900 TOOTH,C23 0.74 75 0.41 33.05 14.99 3750 1652.50 749.56

65340029 TOOTH,C23 0.74 75 0.42 33.00 14.97 3750 1650.00 748.43

2429901 TOOTH,C24 0.74 75 0.38 28.70 13.02 3750 1435.00 650.91

A001378 TOOTH,RB21SN 0.74 75 0.50 36.30 16.47 3750 1815.00 823.27

A001373 TOOTH,RB23 0.74 75 0.46 34.15 15.49 3750 1707.50 774.51

2429939 BLOCK,C20HD 0.74 25 1.18 29.85 13.54 1250 1492.50 676.99

2429938 BLOCK,RC20 0.74 50 0.65 27.30 12.38 2500 1365.00 619.15

Note: Full pallet of teeth contains 50 buckets

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 6

Teeth & Blocks, Bullet, 1”, TC30 Series

PART NO. CODE NO. DESCRIPTION APPLICATION

29919 C31 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For soft to hard rock and concrete. Carbide tip (3/8” dia.) provides strength and long tool life.

2429821 C32 Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For drilling most soils and broken or laminated rock.

A001370 RB31HD Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For drilling most soils and broken or laminated rock.

A001377 31SN-FL Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For drilling most soils and broken or laminated rock.

A001372 RB40XHD Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For drilling most soils and broken or laminated rock.

A001537 RC31HD Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For drilling most soils and broken or laminated rock.

2429228 TX40HD Heat treated alloy steel body, sharp-nose carbide tip, short retainer

For drilling most soils and broken or laminated rock.

PART NO. DESCRIPTION SHANK

SIZE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

29919 TOOTH,C31 0.99 25 1.06 27.35 12.41 1250 1367.50 620.29

2429821 TOOTH,C32 0.99 25 1.08 28.10 12.75 1250 1405.00 637.30

A001370 TOOTH,RB31HD 0.99 40 1.09 43.85 19.89 2000 2192.50 994.50

A001377 TOOTH,31SN-FL 0.99 25 1.05 26.85 12.18 1250 1342.50 608.95

A001372 TOOTH,RB40XHD 0.99 30 1.37 42.55 19.30 1200 1702.00 773.64

A001537 TOOTH,RC31HD 0.99 25 1.01 26.80 12.16 1250 1340.00 607.82

2429228 TOOTH,TX40HD 0.99 25 1.38 34.50 15.65 1250 1725.00 782.45

Note: Full pallet of teeth contains 50 buckets

A001372 Full pallet is 40 buckets

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 7

Teeth & Blocks, Bullet, 1”, TC30 Series

PART NO. CODE NO. DESCRIPTION APPLICATION

2469176 C30 Heavy duty block; 45° mounting surface

Accepts all short retainer teeth. Welded with 7018 or 8018 low-hydrogen rod.

29947 C30H/U40H Extra heavy duty block; 45° mounting surface

Accepts all short retainer and snap ring teeth. Welded with 7018 or 8018 low-hydrogen rod.

A001405 RC30F Block used for core barrels.

For buckets, barrels, and special applications. Welded with 7018 or 8018 low-hydrogen rod.

PART NO. DESCRIPTION SHANK

SIZE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

2469176 BLOCK,C30 0.99 15 3.10 47.15 21.39 750 2357.50 1069.34

29947 BLOCK,C30H/U40H 0.99 8 3.95 32.55 14.76 400 1627.50 738.22

A001405 BLOCK,RC30F 0.99 15 1.30 20.10 9.12 750 1005.00 455.86

Note: Full pallet of teeth contains 50 buckets

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 8

Teeth & Blocks, Bullet, .86, TC87 Series

PART NO. DESCRIPTION SHANK

SIZE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS

PALLET LBS /

PALLET KGS /

PALLET

29918 TOOTH,AR15087LR 0.86 40 0.95 38.55 17.49 2000 1927.50 874.30

2429966 TOOTH,AR15087ST 0.86 40 0.90 36.00 16.33 2000 1800.00 816.47

2429914 TOOTH,C87LR 0.86 60 0.59 35.60 16.15 3000 1780.00 807.39

29945 BLOCK,C87B 0.86 40 0.95 38.05 17.26 2000 1902.50 862.96

29946 BLOCK,C87HDS 0.86 25 1.12 28.45 12.90 1250 1422.50 645.24

PART NO. CODE NO. DESCRIPTION APPLICATION

29918 AR150-87LR

Heat treated alloy steel body, sharp-nose carbide tip, long retainer

Asphalt and other soft to medium-hard conditions. Carbide cutting edge for added protection. Requires LR87 retainer.

2429966 AR150-87ST All-hardened steel cutting face

Asphalt and other soft to medium-hard conditions. All hardened steel tool. Requires LR87 retainer.

2429914 TX87LR

Heat treated alloy steel body, sharp-nose carbide tip, long retainer

Hard rock or concrete. Sharp tip for improved penetration.

29945 C87B Heavy duty block; 45° mounting surface

Heavy duty design (has machined step for non-rotating tools). Welded with 7018 or 8018 low-hydrogen rod.

29946 C87HDS Extra heavy duty block; 45° mounting surface

Extra heavy duty design (has machined shoulder in bore to provide extended life. Welded with 7018 or 8018 low-hydrogen rod.

Note: Full pallet of teeth contains 50 buckets

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 9

PART NO. CODE NO. DESCRIPTION APPLICATION

*A029927 C41 Heat treated alloy steel body, sharp-nose carbide tip w/retainer clip

For large diameter extra heavy duty style augers.

*2429926 C4/U44 Heat treated alloy steel body, sharp-nose carbide tip w/retainer clip

For large diameter extra heavy duty style augers.

A001532 RCDS05 Heat treated alloy steel body, sharp-nose carbide tip, long retainer

For drilling and tunnel boring in the most extreme hard rock and concrete.

*2429930 C7 Heat treated alloy steel body, sharp-nose carbide tip w/retainer clip

For most cutting conditions. No collar.

A000789 DS05 Heat treated alloy steel body, sharp-nose carbide tip, long retainer

For drilling and tunnel boring in the most extreme hard rock and concrete.

A001536 RC4SHF Heat treated alloy steel body, sharp-nose carbide tip, long retainer

For drilling in soft to medium-hard cutting conditions. Sharp nose profile for maximum penetration.

*A001402 RC4SSF Heat treated alloy steel body, sharp-nose carbide tip w/retainer clip

For drilling in soft to medium-hard abrasive cutting conditions. Snap ring attached.

Teeth & Blocks, Bullet, Step, TC4 Series

PART NO. DESCRIPTION STYLE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

A029927 TOOTH,C41 STEP 15 2.58 40.05 18.17 750 2002.50 908.32

2429926 TOOTH,C4 STEP 15 2.60 40.25 18.26 750 2012.50 912.86

A001532 TOOTH,RCDS05 STEP 15 2.52 39.05 17.71 750 1952.50 885.64

2429930 TOOTH,C7 STEP 15 2.30 35.15 15.94 750 1757.50 797.19

A000789 TOOTH,DS05 STEP 12 2.52 30.51 13.87 600 1576.00 714.86

A001536 TOOTH,RC4SHF STEP 15 2.55 39.30 17.83 750 1965.00 891.31

A001402 TOOTH,RC4SSF STEP 10 2.54 25.95 11.77 500 1297.50 588.54

Notes:

1) Full pallet of teeth contains 50 buckets

2) *These teeth use A000679 snap ring (pliers PN A000752 / disposable pliers PN A000137) or retainer

clip PN 65343300TU (push-on style). RETURN TO TABLE OF CONTENTS

PART NO. DESCRIPTION STYLE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS

PALLET LBS /

PALLET KGS /

PALLET

A001401 TOOTH,RC4LSF STEP 10 3.09 31.55 14.31 500 1577.50 715.54

A001639 TOOTH,RC450 STEP 15 2.20 34.25 15.54 750 1712.50 776.78

70796 BLOCK, RC4 STEP 10 3.60 35.80 16.24 500 1790.00 811.93

A001406 BLOCK,RC4F STEP 8 2.43 20.45 9.28 400 1022.50 463.80

Teeth & Blocks, Bullet, Step, TC4 Series

Notes:

1) Full pallet of teeth contains 50 buckets

2) *These teeth use A000679 snap ring (pliers PN A000752 / disposable pliers PN A000137) or retainer

clip PN 65343300TU (push-on style).

PART NO. CODE NO. DESCRIPTION APPLICATION

*A001401 RC4LSF Heat treated alloy steel body, sharp-nose carbide tip w/retainer clip

For medium to hard drilling conditions with added collar to prevent material from entering block and stopping tooth rotation.

*A001639 RC450F Heat treated alloy steel body, sharp-nose carbide tip w/retainer clip

For drilling in soft to medium-hard cutting conditions. Sharp nose profile for maximum penetration. Extra long gauge length for added penetration.

70796 RC4 Heavy duty block; 45° mounting surface

Heavy duty design accepts all step shank tools. Welded with 7018 or 8018 low-hydrogen rod.

A001406 RC4F Heavy duty block with mounting surface parallel to tooth axis

For buckets, barrels, and special applications. Welded with 7018 or 8018 low-hydrogen rod.

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 11

PART NO. CODE NO. DESCRIPTION APPLICATION

2429817 201 Heat-treated dirt tooth regular gauge

Normal dirt digging situations.

2429450 211 Heat-treated dirt tooth outside gauge tooth

Outside tooth for normal dirt digging situations.

2429888 TK225 Four tip conical carbide 1/2” thick. brazedconical carbide

Rock cutting tooth heat treated for strength and durability.

2429436 TX212 TX212 carbide tooth Fits W05 block.

V005053 134 Dirt tooth, extra-wide 5” Normal dirt digging situations.

A001407 RST200P Block For all Taper-Fit Series teeth. Welded with 7018 or 8018 low-hydrogen rod.

A000858 WO5 Block For all Taper-Fit Series teeth. Welded with 7018 or 8018 low-hydrogen rod.

Teeth & Blocks, Taper-Fit Series

PART NO. DESCRIPTION STYLE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

2429817 TOOTH,DIRT,201 Taper-Fit 20 2.38 47.45 21.52 1000 2372.50 1076.15

2429450 TOOTH,DIRT,211 Taper-Fit 15 2.40 37.60 17.06 750 1880.00 852.75

2429888 TOOTH,TK225 Taper-Fit 15 2.72 42.00 19.05 750 2100.00 952.54

2429436 TOOTH,TX212 Taper-Fit 15 2.55 39.20 17.78 750 1960.00 889.04

V005053 TOOTH,DIRT,134 Taper-Fit 3.64

A001407 BLOCK,RST200P Taper-Fit 15 1.85 29.30 13.29 750 1465.00 664.51

A000858 BLOCK,W05 HD Taper-Fit 8 3.25 27.30 12.38 400 1365.00 619.15

Note:

1) Full pallet of teeth contains 50 buckets

2) All these teeth use horseshoe nails (A000010) or rubberlock (A001277)

5-7/8”

5-5/8”

2-1

/2”

3-3

/8”

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 12

PART NO. CODE NO. DESCRIPTION APPLICATION

11376 T101 Heat-treated dirt tooth regular gauge

Normal dirt digging situations.

11370 TO2 Dirt 101 block Flat half pocket that accepts T101 tooth. Welded with 7018 or 8018 low-hydrogen rod.

Teeth & Blocks, Taper-Fit Series

PART NO. DESCRIPTION STYLE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

11376 TOOTH,T101 Taper-Fit 30 1.05 32.25 14.63 1500 1612.50 731.42

11370 BLOCK,T02 Taper-Fit 50 0.78 38.45 17.44 2500 1922.50 872.03

Notes:

1) Full pallet of teeth contains 50 buckets

2) These teeth use horseshoe nails (A000010) or rubberlock (A001277)

2-5/

8”

4-1/4”

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 13

Core Barrel Teeth & Blocks

NOTE: Right Hand, Left Hand, & Center tooth combination works well in reinforced rebar concrete situations.

PART NO. CODE NO. DESCRIPTION APPLICATION

A129932 RJC2 Tooth,RJC2 (center) For high penetration in hard-rock core barrel applications.

A001403 RJR2 Tooth,RJR2 (right) For high penetration in hard-rock core barrel applications.

A001409 RJL2 Tooth,RJL2 (left) For high penetration in hard-rock core barrel applications.

2496804 RJ2 Block,RJ2 Accepts RJ2 teeth only. Welded with 7018 or 8018 low-hydrogen rod.

2429457 TXCB10 Tooth,TXCB10 For high penetration in hard rock core-barrel applications.

2429471 TXH10 Block,TXH10 Accepts TXCB10 teeth only. Welded with 7018 or 8018 low-hydrogen rod.

2429933 U7L/CU7L Tooth,TU7 For high penetration in hard-rock core barrel applications. This tooth is welded on to core barrel.

A000390

A000388

A000378

HEX TEETH

3/4” HEX

1-1/8” HEX

1-3/4” HEX

Excellent for coring through reinforced concrete (rebar).

PART NO. DESCRIPTION STYLE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

A129932 TOOTH,RJC2 CORBAR 50 0.60 31.80 14.42 2500 1590.00 721.21

A001403 TOOTH,RJR2 CORBAR 50 0.66 34.75 15.76 2500 1737.50 788.12

A001409 TOOTH,RJL2 CORBAR 50 0.65 33.95 15.40 2500 1697.50 769.97

2496804 BLOCK,RJ2 CORBAR 50 0.52 27.20 12.34 2500 1360.00 616.89

2429457 TOOTH,TXCB10 CORBAR 50 0.25 14.75 6.69 2500 737.50 334.52

2429471 BLOCK,TXH10 CORBAR 25 0.21 6.60 2.99 1250 330.00 149.69

2429933 TOOTH,U7L/CU7L CORBAR 50 0.57 29.50 13.38 2500 1475.00 669.05

HEX TEETH SEE NOTE BELOW HEX

Notes: 1. All these teeth require roll pin 2443223 except 2429933

2. Full pallet of teeth contains 50 buckets

3. Hex teeth (PN’s A000378, A000388, & A000390) are sold individually.

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 14

Bucket Style Teeth

PART NO. CODE NO. DESCRIPTION APPLICATION

65340659 Tooth, standard, X156 Used for general conditions.

65340660 Tooth, tiger, T156 Used for hard penetration such as frost or semi-hard soils.

65342161TU Nose, weld on, 2" Use w/ 65340659 & 65340660 Teeth. Welded with 7018 or 8018 low-hydrogen rod.

PART NO. DESCRIPTION STYLE PER

BUCKET LBS

EACH LBS /

BUCKET KGS /

BUCKET PCS/

PALLET LBS /

PALLET KGS /

PALLET

65340659 TOOTH,AUG,STD,X156 Bucket 15 1.35 20.75 9.41 750 1037.50 470.60

65340660 TOOTH,AUG,TIGER,T156 Bucket 15 1.95 27.80 9.43 750 1390.00 630.49

65342161TU NOSE,WELD ON, 2" Bucket 20 1.85 45.95 20.84 1000 2297.50 1042.13

Note: All these teeth require roll pin 13347TU

RETURN TO TABLE OF CONTENTS

ph: 1.800.447.2781 fax: 903.957.0015 (Sherman, TX) email: augertools@terex.com

605.882.5595 (Watertown, SD) Effective Date: August 2011, Product specifications and prices are subject to change without notice or obligation. The photographs and / or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and / or its subsidiaries in the USA and other countries. Copyright 2011 Terex Corporation.

TE

ET

H &

BLO

CK

S

Rev D 12/19/11 15

PART NO. CODE NO.

DESCRIPTION APPLICATION

A001388 DS,K150 Puller, DS, K150,Black For removing C4 series step shank teeth with collars and DS teeth.

29937 C123HP,C10 Puller, C123HP, C10,Green For C10 series (.765 shank) bullet teeth.

2429952 C20HP Puller, C20HP,Black For C20 series (.735 shank) bullet teeth.

2429953 C30HP Puller, C30HP,Blue For C30 series (.99 shank) bullet teeth.

A000127 KHP2 Hammer punch, KHP2

For removal of most bullet series teeth. Hardened tip provides long life. Used in conjunction with a hammer.

A000355 KAHP1 Air hammer punch, KAHP1

For removal of most bullet series teeth. Hardened tip provides long life. Fits all light-duty air-hammer guns with a .395” chuck.

65343293TU Hammer punch,1/2” For removal of conical tools from blocks. Use with TC10 & TC20 teeth.

65343294TU Hammer punch,3/4” For removal of conical tools from blocks. Use with TC4, TC30, & TC87 Teeth.

A000752 KRP1 Pliers, KRP1, w/replaceable tips

For removal of snap ring, C4.

A000186 Replaceable tips For KRP1 pliers.

A000137 KRP4 Pliers, KRP4, non-replaceable tips

For removal of snap ring, C4.

Tooth Removal/Installation Tools

RETURN TO TABLE OF CONTENTS