1
G. Pulla Reddy Engineering College (Autonomous): Kurnool Department of Electrical & Electronics Engineering Technical Program Schedule of Three-Day National Level Workshop on “Simulation of Electrical Systems using MATLAB” (1 st – 3 rd December, 2010) 01-12-2010 8.45 AM -9.30AM Registration 9.30 AM -10.30AM Inaugural Function 10.30 AM -11.00AM Tea Break 11.00 AM -12.45 PM Introduction to MATLAB/Simulink Dr. C. Srinivasa Rao & A. Kartikeya Sarma 12.45 PM -1.30 PM Lunch Break 1.30 PM - 3.00 PM Introduction to Fuzzy Logic, Neural Networks and Genetic Algorithms Dr. C. Srinivasa Rao 3.00 PM -3.15 PM Tea Break 3.15 PM – 5.00 PM Lab Session – I (hands on experience with MATLAB) Power Systems Power Electronics & Drives 02-12-2010 9.15 AM -10.45AM Optimal Capacitor Placement in Distribution Systems Sri. A. Kartikeya Sarma Mathematical Modelling of Induction Motor Sri. N. Ravisankar Reddy 10.45 AM -11.00AM Tea Break 11.00 AM -12.45PM Fuzzy Logic, Neural Networks and Genetic Algorithms Applied to Load Frequency Control Dr. C. Srinivasa Rao v/f control of induction motor & Space Vector PWM Algorithm for VSI fed v/f controlled Induction Motor Drive Dr. T. Bramhananda Reddy 12.45 PM -1.30PM Lunch Break 1.30 PM – 3.00 PM Lab Session – II (hands on experience with MATLAB) Lab Session – II (hands on experience with MATLAB) 3.00 PM – 3.15 PM Tea Break 3.15 PM– 5.00 PM Lab Session – III (hands on experience with MATLAB) Lab Session – III (Demonstration of SVPWM algorithm implementation on dSPACE kit) 03-12-2010 9.15 AM -10.45AM Load Following in Deregulated Environment Dr. C. Srinivasa Rao Vector Control of Induction Motor Dr. T. Bramhananda Reddy 10.45 AM -11.00AM Tea Break 11.00 AM -12.45PM Introduction to Hybrid Optimization Techniques (Genetic neural, SA-GA, PSO) Dr. C. Srinivasa Rao Direct Torque Control of Induction Motor Dr. T. Bramhananda Reddy 12.45 PM -1.30PM Lunch Break 1.30 PM – 3.30 PM Lab Session – IV (hands on experience with MATLAB) Lab Session – IV (hands on experience with MATLAB) 3.30PM – 4.00PM Demonstration of LABVIEW by Cranes Software 4.00 PM– 5.00 PM Valedictory Function

Technical Schedule of SESM 2010

Embed Size (px)

Citation preview

  • G. Pulla Reddy Engineering College (Autonomous): Kurnool Department of Electrical & Electronics Engineering

    Technical Program Schedule of Three-Day National Level Workshop on Simulation of Electrical Systems using MATLAB (1st 3rd December, 2010)

    01-12-2010

    8.45 AM -9.30AM Registration 9.30 AM -10.30AM Inaugural Function 10.30 AM -11.00AM Tea Break 11.00 AM -12.45 PM Introduction to MATLAB/Simulink

    Dr. C. Srinivasa Rao & A. Kartikeya Sarma 12.45 PM -1.30 PM Lunch Break 1.30 PM - 3.00 PM Introduction to Fuzzy Logic, Neural Networks and Genetic Algorithms

    Dr. C. Srinivasa Rao 3.00 PM -3.15 PM Tea Break 3.15 PM 5.00 PM Lab Session I (hands on experience with MATLAB)

    Power Systems Power Electronics & Drives

    02-12-2010

    9.15 AM -10.45AM Optimal Capacitor Placement in Distribution Systems Sri. A. Kartikeya Sarma

    Mathematical Modelling of Induction Motor Sri. N. Ravisankar Reddy

    10.45 AM -11.00AM Tea Break 11.00 AM -12.45PM Fuzzy Logic, Neural Networks and Genetic Algorithms

    Applied to Load Frequency Control Dr. C. Srinivasa Rao

    v/f control of induction motor & Space Vector PWM Algorithm for VSI fed v/f controlled Induction Motor Drive

    Dr. T. Bramhananda Reddy 12.45 PM -1.30PM Lunch Break 1.30 PM 3.00 PM Lab Session II (hands on experience with MATLAB) Lab Session II (hands on experience with MATLAB) 3.00 PM 3.15 PM Tea Break 3.15 PM 5.00 PM Lab Session III (hands on experience with MATLAB) Lab Session III (Demonstration of SVPWM algorithm

    implementation on dSPACE kit)

    03-12-2010

    9.15 AM -10.45AM Load Following in Deregulated Environment Dr. C. Srinivasa Rao

    Vector Control of Induction Motor Dr. T. Bramhananda Reddy

    10.45 AM -11.00AM Tea Break 11.00 AM -12.45PM Introduction to Hybrid Optimization Techniques (Genetic

    neural, SA-GA, PSO) Dr. C. Srinivasa RaoDirect Torque Control of Induction Motor

    Dr. T. Bramhananda Reddy 12.45 PM -1.30PM Lunch Break 1.30 PM 3.30 PM Lab Session IV (hands on experience with MATLAB) Lab Session IV (hands on experience with MATLAB) 3.30PM 4.00PM Demonstration of LABVIEW by Cranes Software 4.00 PM 5.00 PM Valedictory Function