Technical Ghide - Anchors for ETICS

8/18/2019 Technical Ghide - Anchors for ETICS

1/49

ETICS Anchors

Simply faster,

safer and

more efcient!

As of: June 2011


2/49

Anchor table EJOT fastening systems for ETICS– a solution for everything.

For the anchor table simply fold.

Substrates

Use category A:

Normal weight concrete

Use category B:

Solid masonry

Use category C:

Hollow or perforated masonry

Use category D:

Lightweight aggregate concrete

Use category E:

Autoclaved aerated concrete


3/49

Anchor table

ejotherm anchors with European Technical Approval (ETA)

Fastening solutions for special applications with German DIBt approval

Clinker systems Speciality solutions

EJOT

SDF-S plus

8UB

EJOT

SDP-S plus

8UB

EJOT

SDM-T plus

8/60 U

EJOT

VSD

EJOT

WSS/Keri

Normal weight concrete - -

Clay bricks - -

Solid lime sandstone - -

Vertical ly perforated clay bricks - -

Solid masonry or solid blocks of lightweightconcrete

- -

Sand-lime perforated bricks - -

Lightweight concrete hollow blocks - -

Weather panels of three layer facadeenvelope (concrete)

-

Lightweight aggregate concrete - -

Autoclaved aerated concrete acc. to DIN - - - -

Autoclaved aerated concrete acc. to TGL - - - -

Fasteners for insulation boards Rail systems

ejotherm

STR U

ejotherm

STR H

EJOT

H1 eco

ejotherm

NTK U

ejotherm

NT U

ejotherm

SDK U

ejotherm

NK U

page 18 page 19 page 22 page 23 page 24 page 27 page 28

Normal weight concrete C12/15 acc. to EN 206-1 -

Normal weight concrete C16/20 - C 50/60

acc. to EN 206-1 -

Weather shell of concrete C16/20 - C50/60 - - - - -

Clay bricks (Mz) acc. to DIN 105 -

Solid lime sandstone (KS) acc. to DIN EN 106 -

Solid masonry of lightweight concrete (V)acc. to DIN 18152

-

Vertically perforated clay bricks (Hlz)

acc. to DIN 105 -

Sand-lime perforated bricks (KSL)acc. to DIN EN 106

-

Lightweight concrete hollow blocks (HbL)acc. to DIN 18151

-

Lightweight aggregate concrete (LAC) - - - - -

Vertical coring reference bricks (Hlz) acc. toÖNORM B 6124

- - - - -

Autoclaved aerated concrete P2-P7 - - - - -

Wooden substrates and metal sheets

(without ETA) -

- - - - -

Application ruled in the approval Proof of qualification through tests on the building - no approval

3


4/49

Content

5 Your strong partner

7 ETICS experience

13 References

14 The ejotherm generation

15 The EJOT STR-principle

17 ejotherm washer anchors

18 ejotherm STR U – Cap anchor for concrete and masonry

19 ejotherm STR H – Cap anchor for wood and metal sheets

20 ejotherm STR accessories

22 EJOT H1 eco - Universal hammer-in anchor

23 ejotherm NTK U – Telescope anchor

24 ejotherm NT U – Universal hammer-in anchor

25 EJOT additional washer

26 ejotherm anchors for rail fastenings

27 ejotherm SDK U – Screw-in anchor for rails

28 ejotherm NK U – Hammer-in anchor for rails

29 Accessories for rail fastenings

30 EJOT anchor for clinker systems

31 EJOT SDF-S plus 8UB – Clinker system anchor for concrete and masonry

32 EJOT SDP-S plus 8 – Clinker system anchor for gas concrete

33 Solutions for special applications

33 EJOT SDM-T plus 8/60U – Specialist for problematic substrates

34 EJOT VSD – Renovation anchor for prewall shells

35 EJOT WSS and Keri – Renovation rods for weather shells

36 EJOT special drill – for optimum loads in perforated bricks

36 EJOT spiral anchor – for fastening of light attachments on ETICS facades

37 Fasteners for ceiling insulation

38 EJOT DDS and DDT – Ceiling insulation screw with additional washer

39 EJOT DDA – Ceiling insulation anchor

40 EJOT anchor basics

4


5/49

Imprint

Publisher:

EJOT Baubefestigungen GmbH

57334 Bad Laasphe

Germany

Layout and execution:

conception Werbung & Marketing GmbH, 57072 Siegen


Photos:

Title and Underground garage, Niels Otto

Bricklayer, Birgid Allig/zefa/Corbis

Freiherr-vom-Stein-Gymnasium, Münster, Christian Richters Fotografe

Schlossarkaden Braunschweig, ECE

Products, Theissen Fotodesign

Print:

Schlabach GmbH & Co. KG, D-57339 Erndtebrück

Legal notes:

Our latest sales terms and delivery conditions apply.

EJOT products are constantly enhanced. They are subject to technical changes,

assortment and price changes. During planning and use of our products please

comply with accepted engineering rules, planning laws as well as relevant safety

regulations. The national technical approvals granted to our products can be

downloaded on the internet at www.ejot.com.

© by EJOT Baubefestigungen GmbH

EJOT® is a registered trademark of EJOT GmbH & Co. KG.

ejotherm® is a registered trademark of EJOT Baubefestigungen GmbH.

TORX® is a registered trademark of Camcar, Div. of Textron, Rockford, IL.

5


6/49

Your strong partner

EJOT Building Fasteners:

Over 30 years ofspecialist knowledge

around the building

envelope

1

4

2

3

a

c

a

b

5

Industrial lightweight construction (ILB)

High-quality fastener products for xing proled

sheets and sandwich panels on industrial steel frameconstruction

External Thermal Insulation Composite Systems

(WDVS)

Special anchors for xing insulation on external wall

systems

Rear ventilated facades (VHF)

Fasteners and anchors for xing brackets to substrate,

frame to brackets, insulation to substrate and facade

fascias on rear ventilated systemsFlat roong (FLD)

Fasteners, stress plates and installation tools for the

efcient attachment of insulation and waterproof

membrane to deck

Industrial Window and Facades Technique (IFF)

Application specic fasteners for UPVC window and

door manufacturing and aluminium/glass curtain wall

systems

Fastening Systems for Solar Installations For fastening uprights for solar and photovoltaic

installations

4

1

2

3

5

6

6

6


7/49


8/49

ETICS competency

Are you absolutely sure what is behind the old rendering?

ETICS are often used in renovation. The major part of the

structural fabric is of bad quality or combined masonry wasused. The bearing capacity of the old render is reduced

through environmental stress.

The ejotherm anchor generation provides safety. Especially

the ejotherm STR U can be used in any substrate. As the

first 8 mm ETICS anchor, it obtained a European Technical

Approval for all building material categories. Despite shortest

anchorage depths, it reaches the highest characteristic loads.

With EJOT quality your service promise will not hang by

a thread…

Your service – Our quality:

EJOT philosophy setsstandards

8


9/49

ETICS competency

„I cannot afford a construction site to stagnate due to

installation problems, and even worse customer

complaints. Today, everything has to be fast and

smooth – but without reduction of quality and

security. EJOT anchors are great to work with.

Especially the STR principle is simply ingenious.

100% setting control and homogeneous insulation

surfaces – thus I can still relax after many years.“

9


10/49

Through our close contact to practitioners and developers,

we are able to develop ideal fastening solutions for today and

tomorrow’s facade insulation systems. Make use of this headstart for your system and experience how decades of know-

how create easy and quick installation.

Based on this practical experience, in special cases our

experts work out individual solutions for you – even right on

the building site.

Some examples of our service:

l personal consultants

l competent consulting via phone or e-mail

l fast and reliable delivery service

l anchor pull-out tests on site

l trainings in fastening technology

l support with bidding processes

Your benefits:

l custom-designed solutions you can rely on

l our decades of know-how

l planning security

Your system – Our know-how:

over 30 years of ETICS anchorsby EJOT

ETICS competency

10


11/49

„As consultant of a system owner, I know

the daily difculties and annoyances that

make life hard for users and cost them

valuable time. With EJOT anchors, the

right choice is easy, and I can rely on that

they work – even when the conditions at

the object are not ideal.“

ETICS competency

EJOT anchors for ETICS are important components

of high-grade facade systems. Like all other system

components they are exclusively sold to system owners.

!

11


12/49

Which anchor do I need for which substrate? What do I do when faced with

mixed masonry? Our ejotherm family with European Technical Approval (ETA)

simplifies your choice. Powerful anchors provide for secure fastening in allsubstrates and with all kinds of insulation materials.

Your benefits:

l clear product range for all substrates

l solutions for all insulation materials

l easy anchor choice

l reduced stock volume

Moreover you have a special programme with cost-efficient special solutions

at your hand. Typical applications are:

l rebuilding the stability of damaged ETICS

l solutions for renovating the renovation

l re-establishing the stability of weather shells and prewall shells

Your advantage –

Our programme:anchor choice

made easy

ETICS competency

Use category A Use category B Use category C Use category D Use category E

Normal weight concrete Solid masonry Hollow or perforated

masonry

Lightweight

aggregate concrete

Autoclaved aerated

concrete

ejothermSTR U

competitive product A

competitive product B

competitive product C

12


13/49

„To me as a planer, energy savings and the design of a new ETICS

facade are most important. Moreover I am responsible that the

facade is secure and immaculate even after years – this is what the

client expects. That is why we advertise ejotherm STR U. If neces-

sary, EJOT experts already consult me during the bidding process

– even right on the building site.“

ETICS competency

13


14/49

During more than three decades, over 500,000,000 sqm

of ETICS facades have been fastened with EJOT anchors

– without even a single incident! This equals an area of morethan 70,000 football pitches. Roughly 150 billion litres of

heating oil or 440 million tons of CO2 have been saved – a

valuable contribution to the environment, which is growing

daily.

More and more international customers and principals rely on

sophisticated fastening solutions and the competent advice

by EJOT.

EJOT - The Quality Connection – also internationally!

EJOT – The Quality Connection:

international customersrely on EJOT

References

Freiherr-vom-Stein-Gymnasium, Munster

Ginger & Fred, Prague Schloss-Arkaden Braunschweig Music Academy, StuttgartEstate Blumlägerfeld, Celle

14


15/49

The ejotherm generation

The new ejotherm generation makes it possible. Specially

developed expansion zones enable highest characteristic

loads with minimum anchorage depths. The result: quickinstallation and economic total cost.

Your benefits:

l up to 45 mm shorter anchor lengths*)

l valuable safety reserves in doubtful substrates

l economic anchor usage

l universal expansion zones for maximum use range

l universal drill diameter for all substrates (8 mm)*) in comparison with earlier EJOT anchors

Short and good –

quick and economic:performance up, costs down

Up to 45 mmshorter

anchor lengths

nominal anchorage depth h nom characteristic load

cost installation time, anchor length, drill abrasion

performance safety, number of anchors/m 2 ,

sensitivity with varying substrate qualit ies

ejothermNT U

competitive product A

competitive product B

Substrate: Vertically perforated clay bricks (Hlz)

Source: specications of the individual European Technical Approval (ETA)

ejothermSTR U

15


16/49

Easy installation:

Quick drilling thanks to reduced drill depth

Put anchor with pre-mounted screw into the hole until

the plate bears on the surface

Screw with the STR tool: countersinking happens

automatically (no milling, no dust)

Insert the STR insulation cap – ready!

The EJOT STR principle

Your guarantee –

Our STR principle

1 2

3 4

For long-lasting beautiful facades

With its STR principle, EJOT has developed a unique fasten-

ing system. Without any additional work, the anchor washers

are installed countersunk and covered with an insulation cap.

This creates a homogenous surface and an even rendering,

which helps to avoid anchor marks.

For all substrates

The ejotherm STR U is the first 8 mm ETICS anchor with

European approval for all building materials, including gas

concrete (use categories A - E). For fastenings on wooden

materials we provide ejotherm STR H. Both anchors are

installed with the same ejotherm STR tool.

For all insulation materials

Both ejotherm STR U and ejotherm STR H can be either

installed countersunk according to the STR principle or plain

with the surface with the STR plug. This way an adaptation to

all commonly used types of insulation is possible.

Quality and safety in XXXL

The EJOT STR princple is available for insulation of up to

400 mm – the perfect fastening system for zero- and low-

energy houses.

1

2

3

4

16


17/49

ejotherm washer anchors

When fastening ETICS, insulation boards are usually attached

to the facade with adhesive and then fastened with anchors.

The bearing load of the system is carried onto the facadevia shearing forces. High-quality washer anchors, installed

through the insulation, guarantee additional contact pressure

through their stiff washers. This contact pressure supports the

permanent frictional bonding between adhesive and substruc-

ture. Due to a strong hold in the wall and the contact pressure

of the washer the clamping of the insulation board is ensured

(„screw clamp effect“).

ejotherm washer anchors with European Technical Approval

offer certif ied safety even under high wind loads. Through their

washers and the expansion element, they redirect the tensile

load into the bearing substructure.

The washer anchors of the ejotherm generation make things

easy for you:

Easy anchor choice for safe anchoring in any building material.

Together with a minimum anchor depth and maximum per-

formance. Performance up, total cost down! For long-lasting,

energy-saving facades.

ejotherm washer anchors –

anchor choice made easy

17


18/49


19/49

Recommended use loads

Wood fibreboards (thickness >_ 17,0 mm) 0.25 kN

Chipboards (thickness >_ 13,0 mm) 0.25 kN

Gypsum fibreboards (thickness >_ 12,5 mm) 0.15 kN

OSB plates (thickness >_ 16,0 mm) 0.25 kN

Solid wood plates (thickness >_ 27 mm) 0.25 kN

The recommended use loads are calculated with a safety factor of 3. They may differ according to the object.

Technical data

Screw diameter 6 mm

Washer diameter 60 mm

Screw-in depth 30 - 40 mm

Installation

ejotherm STR H

Cap anchor for wood and metal sheets

l for wooden substrates as well as metal sheets of up to0.75 mm

l the EJOT STR principle with STR cap for homogenoussurfaces and even rendering- quick and easy without milling dust

l also installable flush with the surface with STR plug

l permanent contact pressure

l 100% setting control: the countersunk installation of theplate signalises safe anchorage

Countersunk installation acc.

STR principle with STR cap

Installation ush with the

surface with STR plug

Product range

Countersunk Installation plain Product name Product code

installation with the surface and

Insulation (mm) Insulation (mm) length (mm)

) – 40 ejotherm STR H 080 8711 080 400

– 60 ejotherm STR H 100 8711 100 400

80 80 ejotherm STR H 120 8711 120 400

100 100 ejotherm STR H 140 8711 140 400

120 120 ejotherm STR H 160 8711 160 400

140 140 ejotherm STR H 180 8711 180 400

160 160 ejotherm STR H 200 8711 200 400 180 180 ejotherm STR H 220 8711 220 400

200 200 ejotherm STR H 240 8711 240 400

220 220 ejotherm STR H 260 8711 260 400

240 240 ejotherm STR H 280 8711 280 400

260 260 ejotherm STR H 300 8711 300 400

Note: Always use in combination with STR cap and STR plug respectively. Packaging: 100 pieces/unit

Special solution: EJOT® self-drilling screw

JT3-ST-2-6,0 incl. washer plate element Ø 60

Special solution for the corrosion resistant fastening ofExternal Thermal Composite Systems made of phenolic resinand mineral wool insulation board.Fastener can optionally be mounted flush with the surface orembedded according to the EJOT STR principle.

For further questions please contact the responsible

EJOT contact person.

19


20/49


21/49

ejotherm STR tool

l specially developed tool for countersunk installation ofejotherm STR U and ejotherm STR H

l sturdy construction for long durability

l wear parts are exchanged quickly

l set comprises: STR-tool, additional cutting metals,

angle screw driver, bits for all applications

ejotherm STR tool spare kit

l to replace wear parts of the STR tool

l set comprises: 3 cutting metals,3 bits for countersunk installation

ejotherm STR accessories

ejotherm STR renovation cutter

l for subsequently securing ETICS facades:cost-efficient re-establishment of the structural stabilitythrough subsequent anchoring

l avoids the de-installation of the old system in many cases

l utilisation of the EJOT STR technology:1. mill the existent plaster layer,

2. install the ejotherm STR U,3. insert the STR cap to obtain an even plaster base,

4. plaster a new final rendering

Product range

Product name Product code Packaging

(pieces/box)

ejotherm STR tool 9151 900 000 1

ejotherm STR tool spare kit 9151 910 000 1

ejotherm STR renovation cutter 9151 940 000 1

21


22/49

EJOT H1 eco

Universal hammer-in anchor

l approved for concrete, solid and

perforated masonry

l solid steel nail (break-proof)

l flush setting of the anchor washer

l plastic injection element to reduce thermal bridgesl installable with additional washer

l shortest anchorage depths, minimum drill hole depth

l high loads for your security


l premounted nail for quick installation

l with EPD (Environmental Product Declaration)

InstallationTechnical Data

Anchor diameter 8 mmWasher diameter 60 mm

Drill hole depth h1 >_ 35 mm

Anchorage depth hef >_ 25 mm

Point thermal transmit tance 0.001 W/K

Use categories acc. to ETA A, B, C

European Technical Approval (ETA) ETA-11/0192

Product range

Insulation (mm) Product name Product code

and length (mm)

New build.¹) Renovation²

)

60 40 EJOT H1 eco 095 8746 095 400

80 60 EJOT H1 eco 115 8746 115 400

100 80 EJOT H1 eco 135 8746 135 400

120 100 EJOT H1 eco 155 8746 155 400

140 120 EJOT H1 eco 175 8746 175 400

160 140 EJOT H1 eco 195 8746 195 400

180 160 EJOT H1 eco 215 8746 215 400

200 180 EJOT H1 eco 235 8746 235 400 220 200 EJOT H1 eco 255 8746 255 400

240 220 EJOT H1 eco 275 8746 275 400

260 240 EJOT H1 eco 295 8746 295 400¹) 10 mm adhesive ²

)10 mm adhesive and 20 mm old render Packaging: 100 pieces/unit

Characteristic loads

Normal weight concrete C 12/15 acc. to EN 206-1 0.9 kNNormal weight concrete C 16/20 - C 50/60 acc. to EN 206-1 0.9 kN

Clay bricks (Mz) acc. to DIN 105 0.9 kN

Solid lime sandstone (KS) acc. to DIN EN 106 0.9 kN

Vertical ly perforated clay bricks (Hlz) acc. to DIN 105,

bulk density ≥ 1,2 kg/dm3 0.75 kN Vertical ly perforated clay bricks (Hlz) acc. to DIN 105,

bulk density ≥ 0,9 kg/dm3 0.6 kN

Sand-lime perforated bricks (KSL) acc. to DIN EN 106 0.9 kNPlease note: For calculation of design loads the national safety factors have tobe included (e.g. Germany: 3). Please observe the approval.

t≥35

Ne w

hammer- in

anc hor

t30t≥35

hv≥25

hv≥25

ø 8

nal mesch

mesh

insulation boardadhesive and levelling mortar

old renderwall construction

22


23/49

Installation Technical data



Anchorage depth h ef >_ 40 mm




Normal weight concrete C 12/15 acc. to EN 206-1 0.6 kN

Normal weight concrete C 16/20 - C 50/60 acc. EN 206-1 0.9 kN



Vertical ly peforated clay br icks (Hlz) acc. to DIN 105 0.6 kN

Sand-lime perforated bricks (KSL) acc. to DIN EN 106 0.9 kNPlease note: For calculation of design loads the national safety factors have tobe included (e.g. Germany: 3). Please observe the approval.

ejotherm NTK U

Telescope anchor

l approved for concrete, solid and perforated masonry

l defined move-in of the washer through the EJOTtelescope effect: with the last blow, the plate decouples

and moves on the sleeve while the expansion zone issafely anchored

l safe and smooth installation with built-in setting controlthrough the EJOT telescope effect

l optimised thermal bridge

l minimised risk of breaking nails due to fibre-reinforcedcomposites

l premounted expansion nail for quick installation

With the next blow the

washer decouples from

the sleeve and moves

into the insulation

EJOT Telescope Effect

Product range

Insulation (mm) Product name Product Code

and length (mm)

New build.¹) Renovation²)

40 – ejotherm NTK U 090 8777 090 100

60 40 ejotherm NTK U 110 8777 110 100

80 60 ejotherm NTK U 130 8777 130 100

100 80 ejotherm NTK U 150 8777 150 100

120 100 ejotherm NTK U 170 8777 170 100

140 120 ejotherm NTK U 190 8777 190 100

160 140 ejotherm NTK U 210 8777 210 100

180 160 ejotherm NTK U 230 8777 230 100¹) 10 mm adhesive ²

) 10 mm adhesive and 20 mm old render Packaging: lengths 090-150: 200, otherwise 100 pieces/unit

Put the anchor into the borehole until

the washer bears on the insulation,

hammer the nail into the sleeve

23


24/49

ejotherm NT U

Universal hammer-in anchor


perforate masonry

l solid steel nail (break-proof)

l plastic injection moulding to reduce thermal bridges

l installable with additional washerl shortest anchorage depths, minimum drill hole depth

l high loads for your security


l premounted nail for quick installation

InstallationTechnical data


Drilll hole depth h1 >_ 35 mm




Product range


and length (mm)

New build.¹) Renovation²)

60 40 ejotherm NT U 095 8796 095 400

80 60 ejotherm NT U 115 8796 115 400

100 80 ejotherm NT U 135 8796 135 400

120 100 ejotherm NT U 155 8796 155 400

140 120 ejotherm NT U 175 8796 175 400

160 140 ejotherm NT U 195 8796 195 400

180 160 ejotherm NT U 215 8796 215 400

200 180 ejotherm NT U 235 8796 235 400

220 200 ejotherm NT U 255 8796 255 400

240 220 ejotherm NT U 275 8796 275 400

260 240 ejotherm NT U 295 8796 295 400¹) 10 mm adhesive ²

)10 mm adhesive and 20 mm old render Packaging: 100 piece/unit






Solid masonry of lightweight concrete (V) acc. DIN 18152 0.5 kN

Vertical ly perforated clay bricks (Hlz) acc. to DIN 105 0.9 kN

Sand-lime perforated bricks (KSL) acc. to DIN EN 106 1.5 kN

Lightweight concrete hollow blocks (HbL) acc. DIN 18151 0.5 kNPlease note: For calculation of design loads the national safety factors have tobe included (e.g. Germany: 3). Please observe the approval.

D iscon t inued

produc t

24


25/49

EJOT VT 90

l washer diameter: 90 mm

l specially for mineral wool boards with low tensile strength

(please observe the approval)l high washer solidness for smooth move-in of the washer

l smooth installation

Additional plates

The washer diameter is enlarged through specially matchedadditional washers. In this way the EJOT washer anchor isperfectly fitted to the demands of different insulation mate-rials. What additional washer is used in a specific case,

depends on the specifications of the ETIC system owner.

When combining our additional washers with ejothermSTR U or ejotherm STR H for the installation flush with thesurface, the special STR closing plugs have to be mounted.

When using additional washers the STR principle cannot beapplied.

EJOT SBL 140 plus


l specially for mineral wool lamella boards

l high washer solidness for smooth installationl high buckling loads thanks to additional plaster bonding

EJOT additional plates

Product range

Product name Product code Packaging

(pieces)

EJOT VT 90 8781 090 008 100

EJOT SBL 140 plus 8716 140 008 100

Mod i f ied

geome tr y

o f t he

was her

25


26/49

ejotherm anchors for rail fastenings

A special kind of External Thermal Insulation Composite

Systems is the mechanical xing of the insulation boards with

the help of holding rails. These systems are preferably used onold facades with large tolerances (unevenness of the old

render) or signicantly damaged old render (lose parts,

partially missing old render).

Holding rails of plastic or aluminium are directly fastened on

the substrate with special collar head anchors. Our spacers

EJOT AS balance tolerances and bridge missing parts.

Simply clip the chosen thickness onto the anchor between

wall and holding rail. System-specic insulation boards are

put into the proles of holding rails through incorporated

grooves.

For additional anchoring of the insulation in the centre of the

board, we recommend our cap anchor ejotherm STR U (see

page 18).

ejotherm anchors for

rail-xed ETICS

26


27/49

Screw-in anchor for rails

l for installing holding and base rails

l approved for all categories of building materials

l shortest anchorage depths, minimum drill hole depths

l highest loads for maximum safety

l economic anchor usagel premounted screw for quick installation

l to compensate facade tolerances use spacers EJOT AS

ejotherm SDK U








Vertical coring reference bricks (Hlz) acc. ÖNORM B 6124 0.75 kN


Lightweight concrete hollow blocks (HbL) acc. DIN 18151 0.6 kN

Lightweight aggregate concrete (LAC) 0.9 kN

Autoclaved aerated concrete P2 - P7 0.75 kNPlease note: For calculation of design loads the national safety factors have tobe included (e.g. Germany: 3). Please observe the approval.

Installation

To compensate facade tolerances use

spacers EJOT AS (p. 29).

Product range

Max. tolerance Product name Product code

compensation (mm) and length (mm)

20 ejotherm SDK U 045 8798 045 400

40 ejotherm SDK U 065 8798 065 400

60 ejotherm SDK U 085 8798 085 400

80 ejotherm SDK U 105 8798 105 400 Packaging: 100 pieces/unit, in box per 1,000 pieces

Technical data

Anchor diameter 8 mm

Collar diameter 16 mm

Drill hole depth h1 >_ 35 mm (75 mm)

Anchorage depth hef >_ 25 mm (65 mm)

Screw drive TORX T30

Use categories acc. to ETA A, B, C, D, E


Values in parentheses: anchoring in gas concrete (use category E )

27


28/49

ejotherm NK U

Hammer-in anchor for rails

l for installing holding and base rails


l shortest anchorage depths, minimum drill hole depths

l high loads for high security

l premounted nail for quick installationl to compensate facade tolerances use spacers EJOT AS

Technical data


Collar diameter 16 mm





Installation

To compensate facade tolerances use

spacers EJOT AS (p. 29).

Product range

Max. tolerance Product name Product code

compensation (mm) and length (mm)

20 ejotherm NK U 045 8797 045 400

40 ejotherm NK U 065 8797 065 400

60 ejotherm NK U 085 8797 085 400 Packaging: 100 pieces/unit, in box per 1,000 pieces









Lightweight concrete hollow blocks (HbL) acc. DIN 18151 0.5 kNPlease note: For calculation of design loads the national safety factors have tobe included (e.g. Germany: 3). Please observe the approval.

28


29/49

Accessories for rail fastenings

EJOT spacers AS

l for levelling out facade tolerances: lengths can becombined individually (3, 5, 8, 10, 15 mm)

l simply clip onto the anchor between wall and rail

l for anchor diameters 6 mm, 8 mm and 10 mm

l sorted by colour

EJOT profile connector PV

l for connecting profile rails

l simply clip onto the rail elements to be connected

l facilitates the precise adjustment of base rails

l length: 30 mm each

EJOT nail anchors ND-K 6 x 60 and 8 x 75

l premounted nail anchor to mount base rails

l diameters: 6 mm and 8 mm

l drill hole depth: >_ 40 mm

l anchorage depth: >_ 30 mm

EJOT installation set

l special composition of frequently used accessories forinstalling base rails

l set comprises: 75 nail anchors ND-K 6 x 60,

10 profile connectors PV, 50 spacers AS 3

Product range

Product name Product code Content/box Content/order

EJOT AS 3 8600 725 700 100 3,000

EJOT AS 5 8601 189 710 100 2,500

EJOT AS 8 8601 233 720 100

EJOT AS 10 8601 232 750 100

EJOT AS 15 8601 187 730 100

EJOT prole connector PV 8792 030 770 100 2,500

EJOT prole connector PV 1150 8792 115 770 10 100

EJOT ND-K 6 x 60 8561 660 400 100 1,000

EJOT ND-K 8 x 75 8561 875 400 100 1,000

EJOT installation set 8500 000 030 1 set 10 sets

29


30/49


31/49

Clinker system anchor for concrete and masonry


l torsion-proof anchor tube

l anchor tube with small countersunk head for unobtrusiveinstallation in the joint

l universal expansion zone for safe anchoringl high loads

l anchor with increased bending moment

l premounted screw for quick installation

EJOT SDF-S plus 8UB

Design loads

Normal weight concrete >_ C 12/15 acc. to EN 206-1 1.0 kN

Weather shell of concrete >_ B 15 0.25 kN

Clay bricks (>_ Mz 12) acc. to DIN 105 0.4 kN

Solid lime sandstone (>_ KS 12) acc. to DIN EN 106 0.4 kN

Solid masonry of lightweight concrete (>_ V 2) DIN 18152 0.2 kN

Vertical ly perforated clay bricks (Hlz) acc. to DIN 105 *

Vertical coring reference brick (Hlz) acc. ÖNORM B 6124 0.75 kN

Sand-lime perforated bricks (>_ KSL 6) acc. DIN EN 106 0.25 kN

Lightweight concrete hollow blocks (>_ HbL 2) DIN 18151 0.15 kN

Lightweight aggregate concrete 0.3 kN

* according to approval to be determined through pull-out tests at the building

The design loads given are in accordance with the German building code.

National safety factors are already incorporated. Please observe the approval.

Installation

Product range


and length (mm) zinc-plated steel steel with Deltaseal¹ ) stainless steel A4

New build. Renovation²)

20 – EJOT SDF-S plus 8UB x 100 8786 100 460 8786 100 692 8786 100 660 40 20 EJOT SDF-S plus 8UB x 120 8786 120 460 8786 120 692 8786 120 660

60 40 EJOT SDF-S plus 8UB x 140 8786 140 460 8786 140 692 8786 140 660



120 100 EJOT SDF-S plus 8UB x 200 8786 200 460 – 8786 200 660

140 120 EJOT SDF-S plus 8UB x 220 8786 220 460 – 8786 220 660¹) organic coating for higher corrosion resistance ²

) 20 mm old render Packaging: 100 pieces unit

Technical data


Diameter of countersunk head 12 mm




German DIBt Approval Z-21.2-589

31


32/49

Design loads

Autoclaved aerated concrete acc. DIN (2 and 3.3 resp.) 0.2 kN

Autoclaved aerated concrete acc. DIN (4 and 4.4 resp.) 0.5 kN

Autoclaved aerated concrete acc. TGL (Laußig plant) 0.3 kN

Autoclaved aerated concrete acc. TGL (Parchim plant) 0.15 kN

The design loads given are in accordance with the German building code.National safety factors are already incorporated. Please observe the approval.

EJOT SDP-S plus 8

Clinker system anchor for gas concrete

l approved for gas concrete

l distort-proof anchor tube

l anchor tube with small countersunk head for unobtrusiveinstallation in the joint

l special expansion zone with hooks for form-fit anchoringl high loads


Installation

Product range


and length (mm) zinc-plated steel stainless steel

New build. Renovation1)

20 – EJOT SDP-S plus 8 x 140 85588 14 456 85588 14 656

40 20 EJOT SDP-S plus 8 x 160 85588 16 456 85588 16 656

60 40 EJOT SDP-S plus 8 x 180 85588 18 456 85588 18 656

80 60 EJOT SDP-S plus 8 x 200 85588 20 456 85588 20 656¹) 20 mm old render Packaging: 100 pieces/unit

Technical data


Diameter of countersunk head 12 mm




German DIBt Approval Z-21.2-967

32


33/49

EJOT SDM-T plus 8/60 U

Specialist for problematicsubstrates


perforated masonry

l universal expansion zone for for problematic substratesand high tolerances

l also available for very thick insulation (up to 340 mm)

l solid steel screw with plastic injection moulded head


Solutions for special applications



Normal weight concrete C 16/20 - C 50/60 acc. EN 206-1 1.5 kNClay bricks (Mz) acc. to DIN 105 1.5 kN


Solid masonry (V) of lightweight concrete acc. DIN 18152 0.9 kN



Lightweight concrete hollow blocks (HbL) acc. DIN 18151 0.75 kN

Regarding design loads the national safety factors are to be incorporated.Please observe the approval.

Installation

Product range


and length (mm)

New build.1) Renovation²

)

40 – EJOT SDM-T plus 8/60 U x 120 8753 120 260 60 40 EJOT SDM-T plus 8/60 U x 140 8753 140 260 80 60 EJOT SDM-T plus 8/60 U x 160 8753 160 260 100 80 EJOT SDM-T plus 8/60 U x 180 8753 180 260 120 100 EJOT SDM-T plus 8/60 U x 200 8753 200 260 140 120 EJOT SDM-T plus 8/60 U x 220 8753 220 260 160 140 EJOT SDM-T plus 8/60 U x 240 8753 240 260 180 160 EJOT SDM-T plus 8/60 U x 260 8753 260 260 200 180 EJOT SDM-T plus 8/60 U x 280 8753 280 260 220 200 EJOT SDM-T plus 8/60 U x 300 8753 300 260 240 220 EJOT SDM-T plus 8/60 U x 320 8753 320 260 260 240 EJOT SDM-T plus 8/60 U x 340 8753 340 260 300 280 EJOT SDM-T plus 8/60 U x 380 8753 380 260 340 320 EJOT SDM-T plus 8/60 U x 420 8753 420 260¹) 10 mm adhesive ²

)10 mm adhesive and 20 mm old render Packaging: 100 pieces/unit

Technical data

Anchor diameter 8 mmPlate diameter 60 mm






33

D iscon t inued

produc t


34/49


35/49


36/49

Solutions for special applications

EJOT spiral anchor

Fastening solution for light attachments onETICS facades

l recommended load: max. 5 kg per mounting point

l no thermal bridges

l simply screw through the final rendering into the insulation(usually without pre-drilling), fasten a 4-5 mm screw (drive

TORX T40) and fix the attachment

EJOT special drill For optimum buckling loads in perforated bricks

l special drill for perforated substrates

l aggressive cutting angle for fast drilling withoutpercussion

l avoids bursting drill holes

l with SDS-plus adapter

l not to be used with percussion or hammer drilling

Product range

Product name Product code

EJOT spiral anchor 8788 000 002

Packaging: 10 pieces/unit, in box per 250 pieces

Installation

Product range

Total length/ Product name Product code

use length (mm)

210 / 150 EJOT special drill 8.0 x 210/150 9200 000 075




36


37/49

The energy optimisation of the building envelope is closely

intertwined with insulating the ceiling on the lowest level.

Especially next to unheated rooms like basements, garages,

warehouses or passages ...

Moreover ceiling insulation is employed to improve acoustics.

It is used for example as noise insulation in commercially used

rooms or halls or as noise protection in shooting ranges.

EJOT fastening solutions

for ceiling insulation

Fasteners for ceiling insulation

37


38/49


EJOT ceiling insulation screw DDS

l fastening of ceiling and acoustic insulation

l easy installation: drill, screw - done!

l short anchorage depth

l plastic injection moulded head with wood wool structure

in colours beige or white for unobtrusive fasteningl special service: coloured varnishing of the screw heads

according to your preferences

Technical data

Head diameter* 25 mm

Drill hole diameter 6 mm




Recommended substrate concrete

*incl. plastic injection moulding

Installation

Lieferprogramm

Use length Product name Product code

(mm) and length (mm) Head with plastic Head with plastic Head colouredinjection moulding white injection moulding beige varnishing white

20-30 EJOT DDS 050 8419 050 740 8419 050 780 5919 050 682

35-45 EJOT DDS 065* 8419 065 740 8419 065 780 5919 065 682

45-55 EJOT DDS 075 8419 075 740 8419 075 780 5919 075 682

55-65 EJOT DDS 085 8419 085 740 8419 085 780 5919 085 682

70-80 EJOT DDS 100 8419 100 740 8419 100 780 5919 100 682

80-90 EJOT DDS 110* 8419 110 740 8419 110 780 5919 110 682

95-105 EJOT DDS 125 8419 125 740 8419 125 780 5919 125 682

105-115 EJOT DDS 135 8419 135 740 8419 135 780 5919 135 682

120-130 EJOT DDS 150 8419 150 740 8419 150 780 5919 150 682

135-145 EJOT DDS 165* 8419 165 740 8419 165 780 5919 165 682

145-155 EJOT DDS 175 8419 175 740 8419 175 780 5919 175 682170-180 EJOT DDS 200 8419 200 740 8419 200 780 5919 200 682

195-205 EJOT DDS 225* 8419 225 740 8419 225 780 5919 225 682

220-230 EJOT DDS 250* 8419 250 740 8419 250 780 5919 250 682

*Special length: available on request Packaging: 100 pieces/unit

38


39/49

EJOT ceiling insulation washer DDT

l to combine with ceiling insulation screwEJOT DDS to enlarge the washerdiameter when it comes to soft insulationmaterial

l lacquering of the entire surface onboth sides, including the edges

l optimised washer geometry for improved fit ofthe EJOT DDS screw into the washer

l increased protection from corrosion and sharp edges


l white lacquering - RAL 9002

l special service: coloured lacquering of the fastener headsaccording to customer request


EJOT ceiling insulation anchor DDA

l fastening of ceiling and acoustic insulation

l easy installation: drill, hammer - done!

l available in colours beige or white

Product range

Product name Product code

plate white

EJOT DDT 8721 070 782

Packaging: 100 pieces each.

Technical data

Head diameter 25 mm

Drill hole diameter 8 mm



Recommended substrate concrete

Product range


and length (mm) colour white colour beige

50 EJOT DDA 075 8552 075 004 8552 075 000

75 EJOT DDA 100 8552 100 004 8552 100 000

100 EJOT DDA 125 8552 125 004 8552 125 000

125 EJOT DDA 150 8552 150 004 8552 150 000

150 EJOT DDA 175 8552 175 004 8552 175 000 Packaging: 400 pieces each.

39

Ne w

o p t i m i sed

wa s he

r


40/49

To harmonise the EU single market the EU Commission

issued a directive on construction parts (89/106 EWG).

It determines which building parts need to comply with the

following essential requirements regarding their intended

use:

l mechanical resistance and stability

l safety in case of fire

l hygiene, health and the environment

l safety in use

l protection against noise

l energy economy and heat retention

Working groups of the European Organisation for Technical

Approvals (EOTA ) have elaborated criteria on how to preci-sely prove these requirements are fulfilled for ETICS. These

criteria and corresponding testing methods are stated in the

European Technical Approval Guidelines (ETAG). For ETICS

the following guidelines are relevant:

l ETAG 004: external thermal insulation composite systems

with rendering

l ETAG 014: plastic anchors for fixing external thermal

insulation composite systems with rendering

l CUAP according to the relevant ETAG

These guidelines are mandatory for all member states of the

European Union (EU) as for well as those states of the Euro-

pean Free Trade Association (EFTA ), that have signed the

agreements of the European Economic Area (EEA ), Iceland,

Liechtenstein and Norway. The guidelines form the base for

awarding European Technical Approval (ETA ) for individual

products. Construction parts with ETA and certificate of

conformity may carry the CE mark, which enables the free

movement of goods within the member states of the EEA.

This way a uniform appraisal of construction parts and theirfundamental technical specifications is ensured. Therefore

each member state can assume without further testing that

the construction part is generally suitable for the intended

use if planning and construction are done correctly. Never-

theless, the CE mark may not be regarded as a quality mark.

The guidelines assume a prospective useful life of ETICS

of at least 25 years. In accordance with current practical

experiences, the actual useful life may be much longer wit-

hout having to fear fundamental quality impairment. In spite

of that, a guarantee towards the system owner or singlecomponents cannot be inferred.

When processing the products, national requirements

are to be regarded. This way, member states may expli-

citly incorporate specific national or regional requirements

(e.g. different wind loads, safety factors, country-specific

construction methods).

In terms of the EC guideline on construction parts, external

thermal insulation composite systems are kits. The produ-

cer whose system receives an ETA is responsible for care-

fully choosing the single constituents. In accordance with

ETAG 004, components of an ETICS are:

l adhesive

l insulation product

l rendering system (including mesh reinforcement)

l mechanical fixing devices (anchors, holding rails)l ancillary materials (e.g. corner strips and base profile)

The approval lapses if components of various system

owners are used. This constitutes a breach of the building

code that leads to the loss of the warrantee by the owner

and may have legal consequences.

EJOT advises: Buy all system components

exclusively from the provider of an approved system!

An ETICS itself does not contribute to the structural stabi-lity of a building. Especially in renovation the stability of the

wall construction has to be checked if an ETICS shall be

installed. Since it has to carry the dead load of the insulation

system after renovation, the stability might have to be rebuilt

before attaching an ETICS. In particular this effects wall

constructions of multiple shells (buildings with a prewall shell

and precast concrete slab-type constructions).

Building laws background

EJOT anchor basics

40


41/49

Good reasons for anchoring an ETICS

Weathered facade

Facade renovated

with an ETICS

Safe installation on old facades

ETICS are often used for energy efficient refurbishment of

old buildings. Do you know how much load the old render

can actually carry? For decades it was exposed to weather

and emissions, soot, dirt and old paint reduce the bearing

strength of the glue. Or single components are not compa-

tible with the composition of the glue (“saponifying”). After

installing a new ETICS building physics can change the

bearing capacity of the old render (failure of old render) even

after years. Regarding new buildings residues of release oil on

concrete may cause difficulties. Cleaning a facade is complex

and costly. Contaminated waste water has to be collected

and professionally disposed. Furthermore the old render is

imbued when thoroughly cleaned.

However if insulation boards are additionally anchored, usu-

ally no special treatment of the facade is necessary. Only

loose parts of the render, efflorescence and paint flaking off

need to be roughly removed. Possible holes are filled. Even-

tually anchors provide safe support…

Highest structural stability

When insulation boards are solely glued, the deadweight of

an ETICS is passed onto the wall through shearing forces.

The used glue is therefore the only connection between wall

and insulation. Thanks to their specifically solid anchor plate

and high characteristic loads, ejotherm plate anchors give

your facade safe support. Through contact pressure the fric-

tional bond between facade surface and adhesive as well as

between adhesive and insulation board is steadily increased.

This results in a higher stability of the whole system. More-

over anchors with steel screw or steel nail offer higher safety

reserves.

Impact of anchoring:

– dead load of the system is passed on via adhesive and

insulation

– plate anchors provide additional contact pressure

Advantages:

– highest stability for the hole system

– anchor plates divert wind load

– highest security in case of wind loads

Z

D

Q

EJOT anchor basics

41


42/49


43/49

Judginig the substructure

The expansion zone of an anchor has to perfectly fit the wall

substrate found at the building. It is the only way the anchor

can optimally fulfil its function within the ETIC system. This is

why carefully assessing the substructure is highly important.

ETAG 014 (guideline for anchors in external thermal insula-

tion composite systems) distinguishes standard substrates

according to so-called use categories in order to facilitate the

assignment of the matching anchor.

Substrates

Determining the anchor type for the substrate

After the substructure is determined, the proper anchor can

be assigned with its approval since anchors with ETA are

tested and approved for specific use categories. The fol-

lowing cases are possible:

Case 1: The anchor is approved for the determined building

material category. The identified substrate is mentioned in the

ETA of the anchor.

The anchor may be used on the building without further

testing. The loads given in the approval can be used offhand

for calculating the necessary number of anchors. Where

required, national safety factors need to be observed.

Example:

Solid lime sandstone was determined as wall substrate.

This corresponds to use category B. The anchor has an

ETA for use categories A and B. For solid lime sandstones,

the ETA mentions a characteristic load of 1.2 kN. Natio-

nal rules require a security value of 3 for use category B.

Therefore the anchor can be calculated having a design load of

1.2 kN : 3 = 0.4 kN without further testing on the building.

Case 2: The anchor has no approval for the determined buil-

ding material category.

If the determined substrate at the building does not belong to

a use category for which the anchor is approved according to

the ETA, the anchor may not be used on this object. In this

case, the usability of the anchor cannot be proven through

pull-out tests.

Example:

Vertical coring bricks were determined as wall substrate. This

corresponds to use category C. An anchor only approved foruse categories A and B may not be used.

Ways to perfect anchoring

Use category A:Normal weightconcrete

Use category B:Solid masonry

Use category C:Hollow or perforatedmasonry

Use category D:Lightweight aggregateconcrete

Use category E: Autoclaved aeratedconcrete

EJOT anchor basics

43


44/49

EJOT anchor basics

Case 3: The anchor is generally approved for the determined

building material category, but the identified substrate is not

explicitly named in the ETA of the anchor.

The anchor may be used if its usability is proven through tests

on the building. The object specific characteristic loads are

determined through pull-out tests as described in the ETA.

When deducting the design load national safety factors need

to be incorporated.

Example:

Perforated lime sandstone was determined as wall substrate.

This corresponds to use category C. The anchor has an ETA

for use categories A, B, C and D. Nevertheless, perforated

lime sandstone is not explicitly named in the ETA. Pull-outtests with this anchor on the object result in a characteristic

load of 1.5 kN. National rules require a security value of 3

for use category C. The anchor can be calculated having an

design load of 1.5 kN : 3 = 0.5 kN.

Case 4: The anchor is generally approved for the determined

building material category. The identified substrate is already

mentioned in the ETA of the anchor, but the gross density or

the compression strength of the stone differs from the decla-

ration of the approval.

In principle this case corresponds to case 3. The usability for

the substructure can be proven through tests on the building.

Special case: Weather shells of concrete (precast concrete

slab-type construction) are assigned to use category A. With

any ejotherm anchor the loads may be calculated employing

tests on the building.

EJOT advises:l The ejotherm STR U (as plate anchor) as well as the

ejotherm SDK U (for fastening rails) have a European

Technical Approval for all building material classes. Many

substrates are already tested for the approval and named

in the ETA. Therefore usually no additional tests are

necessary.

l Should tests on the building site be needed, you have

EJOT’s service at your hand.

Further criteria for choosing the perfect anchor

If in principal several anchor types are applicable in the found

building material, further assessment criteria can be emplo-

yed.

Additonal plates depending on the application


1When applying the STR principle for countersunk installation.

2 A bigger range of application offers more securit y regarding uctua ting

substrate qualities and mixed masonry.

3Please note possible differences between effective and nominal anchorage

depth when comparing with other products.

Depending on the application, our ETICS anchors are com-

bined with additional plates. The additional plates are very

simple to use and are available in various diameters. They are

put on the plate anchor like a washer. The further installationis processed as usual. In which case a specific additional

plate is applied, depends on the used insulation and the

system configuration. Crucial are the specifications of the

system owner.

Note: Additional plates are system components of the

anchor. They are tested accordingly and described in the

approval of the anchor. Therefore plate anchors may only be

combined with the matching additional plates by the same

manufacturer.

Example ejotherm STR U

100% setting control 1)

Homogenous insulation surface

Even rendering

Permanent contact pressure

Less work thanks to premounted

expansion element

Installation behaviour ++

Loads ++

Reduction of thermal bridges +

Range of use2 ++

Anchorage depth 3 ++

44


45/49

Determining the necessary anchor length

The correct determination of the anchor length is an impor-

tant prerequisite to obtain the highest fastening safety pos-

sible. The object specific preconditions always have to be

taken into account, but determining the necessary anchorage

length itself is easy:

nominal anchorage depth hnom+ tolerance compensation ttol+ insulation thickness hD= necessary anchor length lD

h1 = drill hole depthhef = effective anchorage depthhnom = nominal anchorage depth (>_ hef )ttol = tolerance compensationhD = insulation thickness

Notes:

If no other specifications are given, the nominal anchorage

depth hnom is equal to the effective anchorage depth hef .

The tolerance compensation consists of: thickness of old render (if existent, the old render often is

approx. 20 mm thick)+ thickness of the adhesive joint after pressing the insula-

tion boards against the wall (as a rule approx. 10 mm)*+ additional compensation of facade unevenness*= tolerance compensation ttol

If during the energetic renovation there is a larger facade

unevenness to compensate, it may be necessary to employ

different anchor lengths.

Determining the necessary number of anchors

The necessary number of anchors has to be determined

for each building individually. According to new European

and national wind load standards several factors have to be

incorporated. Amongst the most essential influences are the

building construction (height, ground plan, profile) as well

as the surroundings of the building. Exposed conditions in

coastal areas, on mountains or outside closed housing areas

normally lead to significantly higher wind loads. Details and

actual maps with zones of different wind loads are part of

national standards.

From the system point of view the anchor usage is increased

by the bearing load of the used insulation board as well as

the characteristic load and the plate stiffness of the emplo-yed anchors. Therefore the working guidelines of the ETICS

provider have to be observed.

Generally speaking: the higher the building and the more

exposed its surrounding area, the higher the necessary

number of anchors. On the other hand high-quality anchors

often mean a lower usage of anchors per square metre – and

thus save material cost and working hours.

Correct processing is crucial for the function of the

anchor

The position of the anchor results from the anchor scheme

of the ETIC system owner. Common anchorage alignments

are for example:

l alignment of anchors for insulation boards with formats

1000 x 500 mm, e.g. rigid foam plates of polystyrene and

800 x 625 mm, e.g. mineral wool plates (table 1)

l alignment of anchors for insulation boards with formats

1000 x 200 mm, e.g. lamella plates of mineral wool(table 2)

Anchors should always be installed in the area of the adhe-

sive, so that they can support the adhesive joint by means of

contact pressure in the best way possible.

* Facade tolerances are eventually compensated through the actual total thicknessof the adhesive mortar.

EJOT anchor basics

h1 ttol

hDhef = hnom


45


46/49

EJOT anchor basics


4

4

Table 2

6

8

10

Anchors per

square metre

Anchor alignment

Table 1

8

10

12

14

6

Anchors per

square metre

Anchor alignment

46


47/49


48/49

EJOT advises:

When drilling in rotary mode (without percussion), use our

special drills to achieve a clean hole in a short time.

Drills are wearing parts. Their durability depends on the

solidness of the substructure: The harder it is, the higher the

abrasion. To achieve an efficient work progress, drills should

be exchanged in time.

When drilling, please exactly follow the specified installation

values of the individual anchor type (especially the minimum

drilling hole depth). The exact geometry of the drill hole is

important for the bearing capacity of the anchor. Therefore

always drill on a 90 degree angle and never change direction

while drilling. This is especially important with regards to softsubstrates. Before inserting the anchor clean the hole from

drill dust by pulling out the drill several times.

With regards to plate anchors the anchor plates are either

installed countersunk into the insulation board following the

EJOT STR principle or plain with the surface on the insulation

exterior (always in combination with additional plates). When

installing plain with the surface it should be regarded that

the upper side of the anchor plate forms one level with the

upper side of the insulation. When the plate moves in too

deeply, the cavity needs to be levelled out before installing

the mesh. This leads to heightened plaster in the area of the

plate and bears the risk of cracking plaster. When the plate

does not enter deep enough, a thicker mesh layer has to be

installed over the whole facade in order to achieve the mini-

mum render thickness over the anchor plates. This results in

higher costs.

EJOT advises: When using the EJOT STR principle, the

anchor plate is quickly and cleanly countersunk into the

insulation and covered with an STR cap. This way a smoothand homogenous insulation surface as basis for an even

rendering is established. No additional work for levelling out

the anchor plates is needed. Moreover, the anchor plates are

detached from the rendering.

Plate moves in too deeply

Plate not deep enough

Perfect: installation of ejotherm STR with cap

EJOT anchor basics


48


49/49

EJOT Building Fasteners

There for you worldwide!

AUSTRIA

EJOT Austria GmbH & Co KG Grazer Vorstadt 146

A-8570 Voitsbergphone: +43 (3142) 276 00-0fax: +43 (31 42) 2 76 00-30

e-mail: [email protected]

BALTIC STATES

UAB EJOT Baltic Titnago g. 19LT-02300 Vilniusphone: +370 (5) 23 11-437fax: +370 (5) 23 11-439e-mail: [email protected]

BENELUX

EJOT Benelux bvba / sprlReedonk 19-1B-2880 Bornemphone: +32 (0)3 740 79 70fax: +32 (0)3 740 79 79


BULGARIA

EJOT Bulgaria EOOD & Co. KD

Aleksandar Stamboliyski Blvd. 205- Building B, ofce 326 -

BG-1309 Soa

phone: +359 2 812 6569fax: +359 2 812 6569e-mail: [email protected]

BOSNIA AND HERZEGOVINA

EJOT d.o.o. Sarajevo

Rajlovacka b.b.BiH-71000 Sarajevo

phone: +387 33 769 275fax: +387 33 769 276e-mail: [email protected]

CROATIA

EJOT Spojna Tehnika d.o.o.

Franje Luč ić a 23/3

HR-10090 Zagrebphone: +385 (1) 3 49 86 12fax: +385 (1) 3 49 89 63e-mail: [email protected]

CZECH REPUBLIC

EJOT CZ, s.r.o.

Zdĕbradská 65

CZ-25101 R ˇ ič any-Jažlovicephone: +420 (3 23) 63 78 11

fax: +420 (3 23) 63 7818e-mail: [email protected]

DENMARK

EJOT Danmark ApSIndustrisvinget 8DK-4683 Rønnedephone: +45 (56) 39 08 42fax: +45 (56) 39 9106e-mail: [email protected] www.ejot.dk

FRANCE

GERMANY


In der Stockwiese 35D-57334 Bad Laasphephone: +49 (2752) 9 08-0fax: +49 (2752) 9 08-7 31


HUNGARY

EJOT Hungária Kft.Ócsai út 1-3H-1239 Budapestphone: +361 289 3090fax: +36 1289 3091e-mail: [email protected]

ITALY

EJOT Italia srl.

Via Migliarone, n. 21/bis

I-10091 Alpignano Torinophone: +39 (011) 9 68 29 00

fax: +39 (011) 9 78 6741e-mail: [email protected]

NORWAY

EJOT Festesystem A/S Aslakveien 20A N-0701 Oslophone: +47 (23) 25 30 40fax: +47 (23) 25 30 41e-mail: [email protected]

POLAND

EJOT Polska

Spółka z ograniczoną

odpowiedzialnością SpółkakomandytoUl. Jeżowska 9 PL-42-793 Ciasnaphone: +48 (34) 3 51 06 60fax: +47 (23) 3 53 54 10e-mail: [email protected]

ROMANIA

EJOT România S.R.L.

Sos. Bucuresti-Pitesti nr.161 bisRO-117715 Stefanestiphone: +40 (2 48) 22 38 86fax: +40 (248) 22 38 87e-mail: [email protected]

RUSSIA OOO EJOT Wostok

107497 Russia, Moscow

ul. Amurskaya 5, Bau 7

phone: +7 (495) 941 95 84fax: +7 (495) 941 95 69mobile: +7 (910) 002-82 36e-mail: [email protected]

SERBIA

EJOT Tehnika spajanja d.o.o.

Autoput Beograd-Novi Sad 296XSCG-Serbia, 11080 Zemun

SLOVAKIA

EJOT Slovakia, s.r.o.

Juzná trieda 82 (Areál VSS)

SK-04001 Košicephone: +4 21 (55) 6 22 17 60fax: +421 (55) 6 7809 57

e-mail: [email protected] www.ejot.sk

SPAIN

EJOT Ibérica S. L.Pol. P 29 - C/ Azuela 78, nave 4

E-28400 Collado Villalba (Madrid)phone: +34 (91) 286 1020fax: +34 (91) 286 1021e-mail: [email protected]

SWEDEN

EJOT & AVDEL System ABSantagsvägen 9S-70236 Örebrophone: +46 (19) 20 65 00

fax: +46 (19) 20 65 14e-mail: [email protected]

SWITZERLAND

EJOT Schweiz AGUttwiler Straße 3CH-8580 Dozwilphone: +41 (71) 414 52 22fax: +41 (71) 4 1452 50e-mail: [email protected]

TURKEY

EJOT Tezmak Cebeci Cad. No. 84

TR-34100 Küçükköy-Istanbul

phone: +90 (2 12) 5 38 00 01fax: +90 (212) 5 38 00 93e-mail: [email protected]

UNITED ARAB EMIRATES

EJOT Middle East FZE

Sharjah Airport InternationalFreezoneP.O. Box 120588 SharjahUnited Arab Emiratesphone: +971 6-55797-70fax: +971 6-55797-75e-mail: [email protected]

UNITED KINGDOM

EJOT U.K. Ltd.Hurricane CloseSherburn Enterprise Park Sherburn-in-ElmetGB-Leeds LS25 6PBphone: +44 (19 77) 68 70 40fax: +44 (19 77) 68 70 41e-mail: [email protected] www.ejot.co.uk

Documents

Technical Ghide - Anchors for ETICS