Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
Technical ApplicationGuide for UP-SHINELED DownlightUP-DL36-50W(10 inch)
Introduction
www.upshineled.com [email protected]
Up-shine DL36 downlight retrofit kits are designed with CREE COB LED chip, utilization of high efficient reflector helps to improve lumen output. 4inch, 6inch 8inch and 10inch full sizes with wattage varies from 15W to 50W for different applications. 0-10V dimmable driver works with most of the local dimmers. UL&cUL and energy Star approved, qualified for North America Market.
● Up to 70% energy saving compared to standard CFL● Long lifetime of 36,000 hours ● 0~10V dimming driver● 40° wide beam angle● CCT: 2700K 3000K 4000K 5000K● No UV/IR light● Environment friendly, without Mercury or any other hazardous substances
Application notes● IP20 for indoor use● Professional electrician for installation only ● Switch off before installation● Do not touch when in use● Keep away from hot steam and corrosive gas
Application AreasIt is designed for general lighting applications in office, supermarket, shop, school, hotel, etc. It is also widely used for public areas, such as stairway, lobby, reception, corridors etc.
Certificate
Technical Specifications
Model Voltage Power PowerFactor
Lumen(±5%)
Beamangle CCT Lifespan CRI Dimmable Dimension
UP-DL36-50W AC100-277V 50W ≥0.9 3500 40o 2700K 36000h ≥83 Yes Ø276*235mm
UP-DL36-50W AC100-277V 50W ≥0.9 3700 40o 3000K 36000h ≥83 Yes Ø276*235mm
UP-DL36-50W AC100-277V 50W ≥0.9 4000 40o 4000K 36000h ≥83 Yes Ø276*235mm
UP-DL36-50W AC100-277V 50W ≥0.9 4000 40o 5000K 36000h ≥83 Yes Ø276*235mm
Fixture Compatibility
Rated Wattage
ElectricalClassification
IngressProtection
OperatingTemp
OperatingHumidity
Storage Temp
50W Ⅱ IP20 -20oC~45oC 0~90% -20oC~65oC
Driver data Sheet
Driver data DIM
Input rated Voltage AC100-277V
Frequency 50/60Hz
Input Voltage AC90-305V
Efficiency ≥85%
Total load Wattage 50W±5%
Power Factor ≥0.9
Rated input current ≤0.6A
Full load output Voltage DC35-38V
Rated output current 1200mA
Output current range 1200mA±5%
Power tolerance ±5%
Current output tolerance ±5%
Dimming range 8%-100%
Dimmer 0V-10V dimmers
Short circuit protection PASS
Over voltage protection PASS
Over temperature protection PASS
Withstand voltage AC3750V
www.upshineled.com [email protected]
Product Information
235
Ø276
Ø233
Photometric Diagram
Spectral Distribution
www.upshineled.com [email protected]
380 500 600 700 800Wavelength(nm)
Max=6788 [1.0=20000] 1.13SDCM F2700K
x=0.3439 y=0.3656
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0380 500 600 700 800
Wavelength(nm)
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
380 500 600 700 800Wavelength(nm)
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0380 500 600 700 800
Wavelength(nm)
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 37.8 DEG
-/+180
-120
-90
-30
120
90
30
0
1500
3000
4500
6000
7500
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)75
67.5
60
52.5
45
37.5
30
22.5
15
7.5
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 39.8 DEG
-/+180
-120
-90
-30
120
90
30
0
1300
2600
3900
5200
6500
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)60
54
48
42
36
30
24
18
12
6
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 39.1 DEG
-/+180
-120
-90
-30
120
90
30
0
1500
3000
4500
6000
7500
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)75
67.5
60
52.5
45
37.5
30
22.5
15
7.5
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 37.9 DEG
-/+180
-120
-90
-30
120
90
30
0
1500
3000
4500
6000
7500
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)75
67.5
60
52.5
45
37.5
30
22.5
15
7.5
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Max=8694 [1.0=20000] 2.05SDCM F5000K
x=0.3473 y=0.3564
Max=7171 [1.0=20000] 2.12SDCM F4000K
x=0.3841 y=0.3816
Max=5338 [1.0=20000] 3.50SDCM F3000K
x=0.4464 y=0.4049
Height Eavg, Emax Angle: 37.9deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 1643 lm
2.157ft67.93cm
4.335ft131.71cm
6.74ft222.2cm
10.23ft297.81cm
10.24ft333.88cm
430.8, 617.2fc4489, 7077lx
102.5, 168.7fc1157, 182.4lx
48.9, 72.44fc523.47, 804.6lx
17.11, 27.04fc184.69, 295.8lx
26.97, 41.2fc287.41, 456.1lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
Height Eavg, Emax Angle: 37.44deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 1805 lm
2.223ft67.77cm
4.447ft135.54cm
6.67ft203.31cm
8.894ft271.09cm
11.12ft338.86cm
450.2, 687.7fc4846, 7402lx
112.5, 171.9fc1211, 1851lx
50.02, 76.41fc538.4, 822.5lx
18.01, 27.51fc193.8, 296.1lx
28.14, 42.98fc302.8, 462.6lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
Height Eavg, Emax Angle: 37.65deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 1659 lm
2.115ft67.5cm
4.454ft133.05cm
6.55ft201.46cm
8.765ft269.85cm
11.18ft340.90cm
433.1, 654.2fc4576, 7153lx
105.3, 170.5fc1189, 183.2lx
50.0, 73.48fc524.89, 817.9lx
18.00, 26.99fc191.53, 293.4lx
28.33, 42.74fc299.57, 458.7lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
Height Eavg, Emax Angle: 39.24deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 1629 lm
2.339ft71.29cm
4.678ft142.58cm
7.017ft213.87cm
9.356ft285.16cm
11.69ft356.46cm
363.6, 557.3fc3913, 5999lx
90.89, 139.3fc978.3, 1500lx
40.39, 61.92fc434.8, 666.5lx
14.54, 22.29fc156.5, 240.0lx
22.72, 34.83fc244.6, 374.9lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
2700K
2700K
3000K
3000K
4000K
4000K
5000K
5000K
90
80
70
60
50
40
30
20
10
0
11:1
3:13
11:2
5:10
11:3
7:10
11:4
9:10
12:0
1:10
12:1
3:10
12:2
5:10
12:3
7:10
12:4
9:10
13:0
1:10
13:1
3:10
13:2
5:10
13:3
7:10
13:4
9:10
14:0
1:10
14:1
3:10
14:2
5:10
14:3
7:10
14:4
9:10
15:0
1:10
15:1
3:10
15:2
5:10
15:3
7:10
15:4
9:10
16:0
1:10
16:1
3:10
16:2
5:10
16:3
7:10
IC
Capacitor
MOS
PCB
LED
Fitting
Environmental temperature
Tem
pera
ture
(o C)
Time
The driver lifespan is based on capacitor working temperature.
Driver lifetime & LED light decay rate
90000
80000
70000
60000
50000
40000
30000
20000
10000
065oC 75oC 85oC 95oC 105oC
Life
time
(hou
rs)
Capacitor Tc (oC)
Driver Lifetime LED Light Decay Rate
% L
umin
ous
Flux
FLUX
△ U'V'
110%
105%
100%
95%
90%
85%
80%
75%
70%
0.0040
0.0035
0.0030
0.0025
0.0020
0.0015
0.0010
0.0005
0.00000 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
LifeTime (hours)
Polar Diagram Comparison
AVERAGE BEAM ANGLE (50%): 39.8DEG
UNIT: cd
C0/180, 39.8 deg
C30/210, 39.7 deg
C60/240, 39.7 deg
C90/270, 39.8 deg
www.upshineled.com [email protected]
1300
2600
3900
5200
6500
0O
+/-180O
150O-150O
120O-120O
90O-90O
60O-60O
30O-30O
0
Temperature● The testing is operated at 25°C
● The lifetime of capacitor, minimum of 5,000 hours if operated at 105°C, will be doubled whenever the temperature drops 10°C
● The highest withstand temperature of IC, MOS could be 120°C
● The highest withstand temperature of LED junction temperature is 150°C
Installation
www.upshineled.com [email protected]
NOTE: RETROFIT KIT IS VOLTAGE SPECIFIC. VERIFY PROPER VOLTAGE BEFORE INSTALLATION.
Step 2
Step 5
Step 9
Step 3
Step 6
Step 12
Step 4a
Step 7 Step 8
Step 4b
Step 10 Step 11
Step 1: Remove existing lamp(s)Step 2: Remove and discard existing reflector.Step 3: Open board of side of J-box.Step 4: See 4A and 4B Locate J-box containing supply wires and cut all supply wires leading to the ballast and output lead of ballast. (May remove wires of ballast)Step 5: Twist out conduit knockout.Step 6: Place LED Driver box thru ceiling cut-out and allow to rest on ceiling.Step 7: Install the supply conduit of Driver Box into the junction box.Step 8: Connect the supply to the LED Driver. Connect GND to wire of green.Step 9: See figure 9, hold the end of the string and pass through the hole on one side of the fixture. press a while penetrate though the hole inside, and make it tighten. (please clarify where the wire is tighted and the tool is not described)Step 10: Plug the yellow connector of new LED engine to the yellow connector on the end of the flex conduit provided on the driver box.Step 11: Plug the connector of metal to hole of LED engine.Step 12: Ensure the mounting frame can hold the weight of the whole reflector.Step 13: Restore power after installation of fixture is completed.Step 14: After modification completed, attach the Lamping Replacement Marking Label and Cautionary Label which provided with the retrofit kit package to the light fixture. The label shall be visible during relamping, and after installation.
Retrofit Kit Contents
A Engine and Light Source
B Reflector
C LED Driver Box
Packaging Information
SIZE(CM) N.W/pc(KGS) G.W.(KGS) Q'TY(PCS)
Carton 68.5*68.5*29 2.3 10.5 4
CTNS Q'TY(PCS) VOLUME(CBM)
20'' standard container 200 800 28
40'' standard container 400 1600 56
www.upshineled.com [email protected] Phone: +86 755 2919 7389Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China
A
BC