TE653ELW-M Complete Weather Forecaster with Indoor
-
Upload
others
-
View
1
-
Download
0
Embed Size (px)
Citation preview
TE653NLW Instruction Manual.qxdUSER MANUAL
INTRODUCTION
Thank you for selecting a Meade Instruments Weather Forecaster.
This device combines precise time keeping, monitoring and
displaying of current temperature data from up to three remote
locations (additional sensors are required).
Meade Instruments is the world’s leading designer and manufacturer
of telescopes for professional and amateur astronomers – famous for
its innovative, high performance telescopes at affordable prices.
Meade Instruments now brings that same passion for innovation and
high performance to its own line of precision, feature rich weather
stations.
Please read this instruction manual so that you can get the most
enjoyment out of your Meade Instruments weather station.
In this package, you will find:
• One (1) main unit (receiver) • One (1) three-channel remote
sensor (transmitter) • One (1) user manual
Please keep this manual handy as it contains practical
instructions, technical specifications and precautions.
2
INSTALLATION
Communications between the main unit (receiver) and the remote
sensor (transmitter) is wireless. This allows you to greater
flexibility in choosing the location of remote sensor. The remote
transmits data up to 164 feet (50 meters) over an open,
unobstructed area. The remote sensor can be located either indoors
or outdoors, allowing you chose where your data is obtained.
NOTE:
• It is critical to power the remote sensor BEFORE setting up the
main unit.
• It is critical to power up and test communication between the
remote sensor and the main unit BEFORE permanently mounting if
outside.
BEFORE YOU BEGIN
• We recommend using alkaline batteries for the remote sensor. If
outdoor temperatures regularly fall below 32°F (0°C), we recommend
using lithium batteries.
• Avoid using rechargeable batteries. (Rechargeable batteries
cannot maintain correct power requirements.)
• ALWAYS install batteries in the remote sensor before the main
unit.
• Insert batteries before first use, matching the polarity in the
battery compartment.
• Press RESET after each battery change with a paper clip or
similar tool.
• During initial set up, place the remote sensor close to the main
unit.
• After reception is established (remote readings will appear on
the main unit’s display), position the remote sensor and the main
unit within the effective transmission range of up to 164 feet (50
meters).
• The main unit must be placed indoors.
NOTE:
• Avoid pressing any buttons on the main unit before the remote
readings are displayed.
• Transmission or reception range may be affected by trees, metal
structures, and electronic appliances, surrounding building
materials and how the main unit and transmitter are
positioned.
• Place the remote sensor so that it faces the main unit
(receiver), minimizing obstructions such as doors, walls and
furniture.
• Though the remote sensors are weather-resistant, they should be
placed away from direct sunlight, rain or snow. The optimal
location for the remote sensor outdoors is under the eaves on the
north side of the building.
3
REMOTE SENSOR
FEATURES • Remote temperature transmission to the main unit via 433
MHz signal • Case can be wall mounted using built-in hanger • 164
feet transmission range without interference • Selection of the
temperature display in Celsius or Fahrenheit • LCD display of
measured temperature and humidity • 3 channel selection •
Temperature display selection - Fahrenheit or Celsius
A LED INDICATOR • Flashes once when the remote sensor transmits a
reading to the main unit. • Flashes twice when battery power is
low.
B BATTERY COMPARTMENT • Holds two AA-size batteries.
C RESET • Resets all previous settings.
D CHANNEL SWITCH • Selects the desired channel before installing
batteries.
E WALL-MOUNT RECESSED HOLE • Keeps the remote sensor on the
wall.
F °C/ °F SWITCH • Selects the temperature display in Fahrenheit or
Centigrade.
THERMO – SENSOR
4 3 3 M H z W I R E L E S S
1
A
C
B
D
E
MADE IN CHINA
TM
PLACEMENT • The remote sensor should be placed under eaves or a
similar location with free air circulation, sheltered from direct
sunlight and extreme weather. • Ideally, place the remote sensor
over soil, rather than asphalt, which would cause false readings. •
Avoid placing the remote sensor near sources of heat, such as
chimneys or hot air exhaust vents. • Avoid areas that collect heat
from the sun and radiate heat, such as metal, brick or concrete
structures, paving, and patios. • The international standard for
the valid air temperature measurements is 4 feet (1.25 meters)
above the ground.
OPERATION Immediately after batteries are installed, the remote
sensor will start transmitting a temperature and humidity data to
the main unit.
MAIN UNIT FEATURES TIME • Precise time and date set via signals
from the US Atomic clock • 12 or 24 hour time format • Manual
adjustment of time and date • Calendar date with month and day in 7
languages English, German, French, Italian, Spanish, Dutch and
Swedish • Dual crescendo alarms with snooze • Programmable ice
warning alarm
WEATHER • Weather forecast for the next 12 to 24 hour in seven
large icons: sunny, slightly cloudy, cloudy, rainy, heavy rainy,
snowy and heavy snowy. • Programmable minimum/maximum temperature
alarm • Indoor/outdoor temperature and humidity in up to 3 remote
locations (additional sensors required) • Barometric pressure in
imperial or metric units • Altitude adjustment for pressure
compensation • 24 hour barometric pressure history chart • Comfort
level indicators (Dry, Humid and Comfort)
5
B. TEMPERATURE/ HUMIDITY window
C. CLOCK window
D. DOWN button • Select the next available mode • Press and hold
for 2 seconds to search for wireless signal from remote sensor. •
Decrease parameters.
E. ALARM button • When time mode has been selected, press once to
display the alarm time of weekday alarm (W), single alarm (S) and
pre-alarm (Pre-AL). • Hold for 2 seconds, set weekday, single and
pre-alarm’s alarm time • When alarm is on, press once to stop the
alarm temporarily.
F. TEMP ALARM button • When temperature mode has been selected,
press once to display the highest or lowest temperature alarm’s
value. • Hold for 2 seconds, set the highest lowest temperature
alarm’s value • When alarm is on, press once to stop the alarm
temporarily.
G. CHANNEL button • Press to display the outdoor temperature
readings of Channels 1, 2 and 3. • Hold for 2 seconds, enter into
the circulation mode and outdoor temperature readings of Channels
1, 2 or 3 will be displayed automatically in every 5 seconds.
H. MODE button • When pressure mode has been selected, press once
to display the local pressure, altitude and sea level. • Press and
hold for 2 seconds to set altitude and sea level. • When time mode
has been selected, press once to toggle between time with seconds
display or time with weekday display. • Press and hold for 2
seconds, set language of the day of the week, year digit, month
digit, date digit, hour format (12/ 24 hours), hour digit and
minute digit. (Note: calendar format is default in month-date
display). • When temperature mode has been selected, press and hold
for 2 seconds to toggle the temperature unit between Celsius or
Fahrenheit.
I. UP button • Press to select the next available mode • Increase
the parameters • In time with seconds display mode, press and hold
for 2 seconds to activate/ deactivate radio controlled time signal
search manually. • In time with weekday display mode, press and
hold for 2 seconds to switch time zone from Pacific, Mountain,
Central to Eastern.
J. HISTORY button • When pressure mode has been selected, press
once to check the historical pressure data for the past 24
hours.
K. MEMORY button • When temperature mode has been selected, press
to recall the minimum or maximum temperature and humidity readings
of main unit and remote units. • Press and hold for 2 seconds,
collected memories will be cleared.
7
MADE IN CHINA
BATTERY INSTALLATION • Remove the battery door located at the back
of the main unit. • Insert two (2) AA batteries and replace the
battery compartment door.
PLACEMENT • Make sure that the main unit is locating within the
operating range of all remote sensors. • Ideally the main unit
should be placed within line of sight of remote sensors. Avoid
placing the main unit where surfaces emitting and radiating heat
(e.g. heating ducts or air conditioners) and areas with
interference from wireless devices (e.g. cordless phones, radio
headsets, baby monitoring devices and other electronics).
OPERATION Once the main unit is powered, the display will show all
available LCD segments for a moment. IMPORTANT: All of the display
functions will be locked, allowing setting of your local altitude
and pressure parameters by pressing the UP (? ) or DOWN (? ) and
SET buttons. The locked display will show the pressure icon and
abbreviation “inHg” flashing in the Weather Forecast/ Pressure
Window, default time in Clock Window and channel 1’s temperature
and humidity readings in Temperature/ Humidity Window. If pressure
and altitude are not configured during this time, the unit will
self-calibrate in a few minutes and show the default settings for
the pressure and altitude (sea level) and all remote weather
sensors readings.
GETTING STARTED
WEATHER FORECAST
This unit is capable of detecting the atmospheric pressure changes.
Based on collected weather data, it forecasts the weather for the
next 12 to 24 hours.
NOTE: The weather forecast accuracy is approximately 70%. The main
unit display shows forecasted (predicted) not current conditions.
The SUNNY icon indicates clear weather, even when displayed during
the nighttime.
When the display shows...
8
L. SNOOZE/ LIGHT button • Stops alarm temporarily and activates LCD
backlight
M. WALL-MOUNT hole • A recessed opening to mount the unit on a
wall
N. BATTERY COMPARTMENT • Requires two (2) AA batteries
O. TABLE STAND • When placing the main unit on the table or other
horizontal surface, unfold and adjust the table stand for the
desired viewing angle.
PRESSURE OPERATION
The pressure window displays: current barometric pressure, sea
level pressure, and weather forecast. The information contains a
number of historical statistics: pressure/ temperature/ humidity
history bar-chart for the past 24 hours. Pressure can be measured
in inHg, hPa/mBar or mmHg, and altitude is determined in either
meters or feet.
IMPORTANT: There are three viewing options available: barometric
pressure SEA LEVEL or LOCAL and ALTITUDE. Local pressure is a
measured value (can’t be adjusted) while Sea Level & Altitude
are variables that you can enter. It is advisable to select and
program only one of the variables and to allow the unit to
calculate the third value. The unit is designed to measure pressure
changes at your specific location, when LOCAL barometric pressure
is selected. Information for programming your unit, with either
Altitude or Sea Level values, may be obtained from GPS readings,
online from the Internet, etc. SEA LEVEL barometric pressure
provides you with information about pressure changes at lower
elevations in your surrounding area. The SEA LEVEL pressure value
can be set to match your local metro area weather information.
(Sources – local TV or radio station, etc.)
SETTING INITIAL PRESSURE PARAMETERS IMPORTANT: Allow the unit to
set without touching ANY buttons for about 6-8 minutes during the
main unit initial set up. This will give the unit time to
synchronize with remotes, stabilize pressure readings and settle
with default settings.
SELECT PRESSURE UNITS OF MEASURE Press UP (? ) or DOWN (? ), as
needed, until the pressure icon “PRESSURE”, to the left of the
barometric pressure value, begins to flash. • Press MODE button, to
toggle through selections until “SEA LEVEL” or “LOCAL” barometric
pressure is displayed. • Press and hold HISTORY button to enter the
pressure unit selection mode. Press the UP (? ) or DOWN (? ) button
to select the preferred units of measure for pressure:
inHG (English), hPa/mBar (scientific) or mmHg (metric) • Press
HISTORY to confirm your selection. Then press MODE to move to the
ALTITUDE unit selection mode. Press the UP (? ) or DOWN (? ) button
to select pressure unit as FEET or METER. • Press HISTORY to
confirm and hold MODE to move to the ALTITUDE value selection mode.
• Press UP (? ) or DOWN (? ) to select or adjust the altitude value
to your location. (Press and hold either button for accelerated
digit advance) • Press MODE to confirm the programming selection.
(NOTE: The unit will automatically exit programming mode if it does
not detect a button press after 2 minutes.)
VIEWING PRESSURE AND ALTITUDE INFORMATION To view pressure or
altitude information, press MODE button. The display will alternate
between the sea level pressure, local pressure and local altitude
screens.
PROGRAMMING SEA LEVEL PRESSURE (not required if you did altitude) •
Press and hold MODE, until the barometric pressure digits are
flashing.
• Enter the desired sea level pressure value by pressing UP (? ) or
DOWN (? ) buttons. (Press and hold either button for accelerated
digit advance.)
• Press MODE, to confirm sea level value selection.
9
• Press MODE as needed, until “LOCAL” pressure is displayed.
• Press and hold HISTORY, until the pressure unit is
flashing.
• Change local or sea level pressure units by pressing the UP (? )
or DOWN (? ) buttons to select the pressure units. Choose from:
inHg, hPa/mBar or mmHg.
• Press HISTORY to confirm your selection.
• Press MODE button until the local altitude value will be
displayed.
• Press and hold HISTORY until the altitude unit is flashing.
• Select the ALTITUDE unit:, meters or feet, by pressing UP (? ) or
DOWN (? ) buttons.
• Press HISTORY to confirm your selection.
VIEWING SEA LEVEL PRESSURE HISTORY
• In pressure mode, press HISTORY button entering the sea level
pressure display.
• When the SEA LEVEL is displayed, press HISTORY repeatedly viewing
the sea level pressure history for the past 24 hours in 1 hour
intervals.
• If no buttons are pressed for 5 seconds, the unit will
automatically return to the default Pressure and Weather Forecast
Mode.
VIEWING PRESSURE, TEMPERATURE AND HUMIDITY CHARTS
The bar chart in Pressure Window can be configured to display a
historical data for the sea level pressure and temperature or
humidity for channel 1.
After selecting the Pressure Window, press and hold ALARM button to
toggle the bar chart between the sea level pressure with a word
“PRESSURE” displayed at the right bottom corner of the chart,
temperature with a thermometer icon and “CH1” and a humidity with
“RH” icon and “CH1”.
MOON PHASE ICONS
TEMPERATURE/ HUMIDITY WINDOW
The main unit supports up to 3 remote sensors, corresponding to a
separate channel of the temperature and relative humidity display.
The temperature can be displayed in Celsius (ºC) or Fahrenheit
(ºF).
The main unit carries the temperature and humidity sensor and uses
this data to calculate an indoors comfort level - Wet, Comfort or
Dry.
A temperature alert function is available for all channels. It can
be programmed to sound if the channel temperature exceeds or falls
below the pre-set upper and lower limits.
10
Corresponding remote sensor signal received successfully
No signals received for over 1 hour
REMOTE SENSORS STATUS The wave icon above the current channel icon
shows the connection status of the corresponding remote
sensor:
SEARCH FOR REMOTE SENSORS • The main unit can be manually activated
to search for the signals from remote sensors by pressing and
holding DOWN (? ) button.
OPERATION • To select the indoor/ outdoor temperature mode, press
UP (? ) or DOWN (? ) until the IN icon flashing with a beep sound
alert.
VIEWING REMOTE (CHANNEL) TEMPERATURE AND HUMIDITY Static Display: •
Press the CHANNEL button to select measurements from different
remote sensors, each is set to a unique channel 1, 2 or 3.
Channel Auto-Scan Display: • To enable an automatic scan of all
channels, press and hold CHANNEL, until the icon is displayed. The
measurements from each remote channel will be alternately displayed
with a 5 seconds viewing.
NOTE: the channel auto-scan feature can be active only if there are
more than one remote sensors operating and are set to different
channels.
PROGRAMMING TEMPERATURE IN CELSIUS OR FAHRENHEIT • Press and hold
MODE button for 3 seconds to toggle the temperature unit in Celsius
(ºC) or Fahrenheit (ºF).
SETTING TEMPERATURE ALARM • Press down button to select temp
display.
• Press TEMP ALARM button selecting the desired alarm, the upper
temperature alert with icon (if disabled, displays OFF), or lower
temperature alert with icon (if disabled, displays OFF).
• Press and hold TEMP ALARM button until the temperature digits
flashing.
• Adjust the temperature digits using the UP (? ) or DOWN (? ).
Press and hold either button for fast digits advance
• Press the TEMP ALARM to confirm selection and return to the
temperature alarm selection screen
ACTIVATING OR DEACTIVATING TEMPERATURE ALARMS • Once the above
alerts are displayed, press the UP (? ) or DOWN (? ) to enable or
disable the corresponding alert.
11
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button
recalling: • Current temperature and humidity • Minimum temperature
and humidity • Maximum temperature and humidity at the remote
location.
Indicator displayed
20°C to 25°C (68°F to 77°F)
40%RH- 70%RH
-5°C to 50°C (23°F to122°F)
OVER 70%RH
Contains excess moisture
BELOW 40%RH
Contains inadequate moisture
RESETTING TEMPERATURE MEMORIES Press and hold MEMORY button for 3
seconds to clear all channel memories.
COMFORT LEVEL INDICATION The main unit is capable of detecting and
displaying the current indoor comfort levels of surrounding
environment. The comfort level based on the combination of the
current indoor temperature and humidity readings. The following
comfort levels may be displayed: COMFORT (comfortable); WET (wet)
and DRY (dry)
CLOCK WINDOW
WWVB RADIO CONTROLLED TIME The NIST (National Institute of
Standards and Technology) radio station (WWVB) is located in Ft.
Collins, Colorado. It transmits an exact time signal continuously
throughout the most of the continental United States at 60 KHz
frequency. The main unit can receive this WWVB signal through the
internal antenna from up to 2,000 miles away. Due to the nature of
the Earth’s ionosphere, reception can be limited during the
daylight hours. The radio controlled clock will search for an
alternate station that receives the atomic time signal from the
NIST Atomic clock in Boulder, Colorado.
The WWVB tower icon on the unit’s display will flash indicating a
radio signal reception from the WWVB station. If the tower icon is
not fully lit, or if the time and date are not set automatically,
please consider the following:
• During nighttime hours, atmospheric disturbances are typically
less severe and radio signal reception may improve. A single daily
reception is sufficient enough to keep the clock accuracy within 1
second.
• Make sure the unit is positioned at 8 feet (2 meters) distance
from any interference source such as a TV, computer monitor,
microwave, etc.
• Within concrete wall rooms such as basements or office buildings,
the received signal may be weakened. Always place the main unit
near the window for better reception.
Once the atomic time signal is received, the date and time will be
set automatically, and the [ ] icon will appear.
12
Undefined data(Flashing)
Weak signal, but can be decoded
Strong signal
• The atomic clock receiver is programmed that it will search for
the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00
am.
• To enable or disable the atomic time receiver, press and hold UP
(? ) button for 3 seconds. If atomic time reception is activated, a
tower icon will start flashing. If reception is disabled, the tower
icon will disappear.
• If the time signal has not been received in 8 minutes, you may
set the time manually. (Refer to the MANUAL SETTINGS
section).
MANUAL SETTINGS To select the time mode, press UP (? ) or DOWN (? )
until the IN icon flashing with a beep sound alert. It is necessary
to set the desired US TIME ZONE.
TIME ZONE • Press MODE button once to select hour and minutes with
the day of the week display.
• Select the Time Zone by pressing and holding UP (? ) button for 3
seconds.
• Keep holding UP (? ) button until the desired US Time Zone
(Pacific, Mountain, Central or Eastern) is highlighted on the
display’s US map, located to the right of the time display and
above the day of the week.
• Release the UP (? ) button. The Time Zone is set.
TIME AND CALENDER • Press and hold MODE button until the day of
week language abbreviation “ENG” will flash
• Press the UP (? ) or DOWN (? ) selecting the day of the week in
English, German, French, Italian, Spanish, Dutch or Swedish.
• After the language of weekday is MODE, press MODE button to
confirm and move to the next parameter (year).
• Continue setting the year, month, day, time format (12 or 24
hours), local hour and minutes, using the same technique.
• After programming is complete the display will return to the
default hour and minutes with seconds display.
13
CLOCK ALARMS There are two time alarms – Weekday alarm (W) and
Single day alarm (S) - and one Ice Warning Alarm (PRE-AL). • If
Weekday (W) alarm is activated, it will sound at the set time and
the alarm icon will flash Mondays through Fridays • If Single (S)
day alarm is activated, it will sound at the set time and the alarm
icon will flash only for this specific day and will not activate on
subsequent days • If Ice Warning Alarm ( PRE-AL) is activated, it
will sound at the set time and alarm icon will flash when the
remote temperature for Channel One (1) reaches 32°F(0°C) and
below.
NOTE: Ice Warning Alarm can be set only if weekday and/or the
single alarm are programmed.
SETTING THE WEEKDAY (W) AND SINGLE DAY (S) ALARMS • Press ALARM
button once to enter into the alarms setting mode. The default
alarm is a Weekday alarm (W). The abbreviation “OFF” with a letter
“W” next to it will be displayed, if the alarm has not been set
previously
• Press and hold ALARM button for two seconds. The hour digit will
flash • Adjust the hour using UP ( ? ) or DOWN ( ? ) buttons
• Press ALARM button again. The minute digits will flash
• Adjust the minutes using UP (? ) or DOWN (? ) buttons
• Press ALARM button again to confirm and the weekday alarm time
will be set
• Set Single (S) day alarm if desired in the same manner
SETTING THE ICE WARNING ALARM (PRE-AL) If Weekday (W) or Single day
(S) alarm is set, the Ice Warning Alarm (Pre-AL) can be
programmed.
• Press ALARM button once to enter into the Ice Warning Alarm
setting mode. The abbreviation OFF with a PRE-AL next to it will be
displayed.
• Press and hold ALARM button for two seconds. The number 30 will
flash, meaning that if selected, the alarm will sound 30 minutes
earlier than the Weekday or Single alarm.
• Select the desired Ice Warning Alarm interval in 15 minutes
increments between 15 and 90 minutes, using UP (? ) or DOWN (? )
buttons
• Press ALARM button to confirm and exit from the alarm setting
mode.
ACTIVATING/ DEACTIVATING ALARMS • Press ALARM button to enter into
the desired alarm mode.
• Press UP ( ? ) to activate alarm and the corresponding icons W, S
or PRE-AL will be displayed.
• Press DOWN ( ? ) to deactivate alarm until “OFF” is
displayed.
MAINTANANCE CHANGING BATTERIES
• If the low battery indicator lights up, replace batteries in the
corresponding unit.
• Do not mix old and batteries.
CLEANING The main unit and remote sensors housings can be cleaned
with a damp cloth. Small parts can be cleaned with a cotton tip or
pipe-cleaner. Never use abrasive or corrosive cleaning agents or
solvents. Do not immerse electronic components in water.
14
Issue
Cannot locate remote sensor
Cannot change the channel
Place unit by the window and keep it there overnight
Check batteries
Check location
Press and hold DOWN ( ? ) button on the main unit to search for the
signal form the remote sensor
Press “RESET” after setting the channel
Initiate manual sensor search (Press and hold DOWN ( ? ) button on
the main unit)
Remote sensor
Symptom Solution
PRECAUTIONS This product is engineered to give you years of
satisfactory service if handled carefully. Here are a few
precautions:
• Do not immerse the units in water.
• Do not clean the units with abrasive or corrosive materials. They
may scratch the plastic parts and corrode the electronic
circuits.
• Do not subject the product to excessive force, shock, dust,
temperature, or humidity, which may result in malfunctions, shorter
lifespan, damaged batteries, and damaged parts.
• Do not tamper with the units internal components. Doing so will
invalidate the warranty and may cause damage. These units contain
no user-serviceable parts.
• Use only fresh batteries. Do not mix new and old batteries. •
Read the user's manual thoroughly before operating the units.
TROUBLESHOOTING
15
BATTERY INSTALLATION • Remove the battery door located at the back
of the main unit. • Insert two (2) AA batteries and replace the
battery compartment door.
PLACEMENT • Make sure that the main unit is locating within the
operating range of all remote sensors. • Ideally the main unit
should be placed within line of sight of remote sensors. Avoid
placing the main unit where surfaces emitting and radiating heat
(e.g. heating ducts or air conditioners) and areas with
interference from wireless devices (e.g. cordless phones, radio
headsets, baby monitoring devices and other electronics).
OPERATION Once the main unit is powered, the display will show all
available LCD segments for a moment. IMPORTANT: All of the display
functions will be locked, allowing setting of your local altitude
and pressure parameters by pressing the UP (? ) or DOWN (? ) and
SET buttons. The locked display will show the pressure icon and
abbreviation “inHg” flashing in the Weather Forecast/ Pressure
Window, default time in Clock Window and channel 1’s temperature
and humidity readings in Temperature/ Humidity Window. If pressure
and altitude are not configured during this time, the unit will
self-calibrate in a few minutes and show the default settings for
the pressure and altitude (sea level) and all remote weather
sensors readings.
GETTING STARTED
WEATHER FORECAST
This unit is capable of detecting the atmospheric pressure changes.
Based on collected weather data, it forecasts the weather for the
next 12 to 24 hours.
NOTE: The weather forecast accuracy is approximately 70%. The main
unit display shows forecasted (predicted) not current conditions.
The SUNNY icon indicates clear weather, even when displayed during
the nighttime.
When the display shows...
8
L. SNOOZE/ LIGHT button • Stops alarm temporarily and activates LCD
backlight
M. WALL-MOUNT hole • A recessed opening to mount the unit on a
wall
N. BATTERY COMPARTMENT • Requires two (2) AA batteries
O. TABLE STAND • When placing the main unit on the table or other
horizontal surface, unfold and adjust the table stand for the
desired viewing angle.
PRESSURE OPERATION
The pressure window displays: current barometric pressure, sea
level pressure, and weather forecast. The information contains a
number of historical statistics: pressure/ temperature/ humidity
history bar-chart for the past 24 hours. Pressure can be measured
in inHg, hPa/mBar or mmHg, and altitude is determined in either
meters or feet.
IMPORTANT: There are three viewing options available: barometric
pressure SEA LEVEL or LOCAL and ALTITUDE. Local pressure is a
measured value (can’t be adjusted) while Sea Level & Altitude
are variables that you can enter. It is advisable to select and
program only one of the variables and to allow the unit to
calculate the third value. The unit is designed to measure pressure
changes at your specific location, when LOCAL barometric pressure
is selected. Information for programming your unit, with either
Altitude or Sea Level values, may be obtained from GPS readings,
online from the Internet, etc. SEA LEVEL barometric pressure
provides you with information about pressure changes at lower
elevations in your surrounding area. The SEA LEVEL pressure value
can be set to match your local metro area weather information.
(Sources – local TV or radio station, etc.)
SETTING INITIAL PRESSURE PARAMETERS IMPORTANT: Allow the unit to
set without touching ANY buttons for about 6-8 minutes during the
main unit initial set up. This will give the unit time to
synchronize with remotes, stabilize pressure readings and settle
with default settings.
SELECT PRESSURE UNITS OF MEASURE Press UP (? ) or DOWN (? ), as
needed, until the pressure icon “PRESSURE”, to the left of the
barometric pressure value, begins to flash. • Press MODE button, to
toggle through selections until “SEA LEVEL” or “LOCAL” barometric
pressure is displayed. • Press and hold HISTORY button to enter the
pressure unit selection mode. Press the UP (? ) or DOWN (? ) button
to select the preferred units of measure for pressure:
inHG (English), hPa/mBar (scientific) or mmHg (metric) • Press
HISTORY to confirm your selection. Then press MODE to move to the
ALTITUDE unit selection mode. Press the UP (? ) or DOWN (? ) button
to select pressure unit as FEET or METER. • Press HISTORY to
confirm and hold MODE to move to the ALTITUDE value selection mode.
• Press UP (? ) or DOWN (? ) to select or adjust the altitude value
to your location. (Press and hold either button for accelerated
digit advance) • Press MODE to confirm the programming selection.
(NOTE: The unit will automatically exit programming mode if it does
not detect a button press after 2 minutes.)
VIEWING PRESSURE AND ALTITUDE INFORMATION To view pressure or
altitude information, press MODE button. The display will alternate
between the sea level pressure, local pressure and local altitude
screens.
PROGRAMMING SEA LEVEL PRESSURE (not required if you did altitude) •
Press and hold MODE, until the barometric pressure digits are
flashing.
• Enter the desired sea level pressure value by pressing UP (? ) or
DOWN (? ) buttons. (Press and hold either button for accelerated
digit advance.)
• Press MODE, to confirm sea level value selection.
9
• Press MODE as needed, until “LOCAL” pressure is displayed.
• Press and hold HISTORY, until the pressure unit is
flashing.
• Change local or sea level pressure units by pressing the UP (? )
or DOWN (? ) buttons to select the pressure units. Choose from:
inHg, hPa/mBar or mmHg.
• Press HISTORY to confirm your selection.
• Press MODE button until the local altitude value will be
displayed.
• Press and hold HISTORY until the altitude unit is flashing.
• Select the ALTITUDE unit:, meters or feet, by pressing UP (? ) or
DOWN (? ) buttons.
• Press HISTORY to confirm your selection.
VIEWING SEA LEVEL PRESSURE HISTORY
• In pressure mode, press HISTORY button entering the sea level
pressure display.
• When the SEA LEVEL is displayed, press HISTORY repeatedly viewing
the sea level pressure history for the past 24 hours in 1 hour
intervals.
• If no buttons are pressed for 5 seconds, the unit will
automatically return to the default Pressure and Weather Forecast
Mode.
VIEWING PRESSURE, TEMPERATURE AND HUMIDITY CHARTS
The bar chart in Pressure Window can be configured to display a
historical data for the sea level pressure and temperature or
humidity for channel 1.
After selecting the Pressure Window, press and hold ALARM button to
toggle the bar chart between the sea level pressure with a word
“PRESSURE” displayed at the right bottom corner of the chart,
temperature with a thermometer icon and “CH1” and a humidity with
“RH” icon and “CH1”.
MOON PHASE ICONS
TEMPERATURE/ HUMIDITY WINDOW
The main unit supports up to 3 remote sensors, corresponding to a
separate channel of the temperature and relative humidity display.
The temperature can be displayed in Celsius (ºC) or Fahrenheit
(ºF).
The main unit carries the temperature and humidity sensor and uses
this data to calculate an indoors comfort level - Wet, Comfort or
Dry.
A temperature alert function is available for all channels. It can
be programmed to sound if the channel temperature exceeds or falls
below the pre-set upper and lower limits.
10
Corresponding remote sensor signal received successfully
No signals received for over 1 hour
REMOTE SENSORS STATUS The wave icon above the current channel icon
shows the connection status of the corresponding remote
sensor:
SEARCH FOR REMOTE SENSORS • The main unit can be manually activated
to search for the signals from remote sensors by pressing and
holding DOWN (? ) button.
OPERATION • To select the indoor/ outdoor temperature mode, press
UP (? ) or DOWN (? ) until the IN icon flashing with a beep sound
alert.
VIEWING REMOTE (CHANNEL) TEMPERATURE AND HUMIDITY Static Display: •
Press the CHANNEL button to select measurements from different
remote sensors, each is set to a unique channel 1, 2 or 3.
Channel Auto-Scan Display: • To enable an automatic scan of all
channels, press and hold CHANNEL, until the icon is displayed. The
measurements from each remote channel will be alternately displayed
with a 5 seconds viewing.
NOTE: the channel auto-scan feature can be active only if there are
more than one remote sensors operating and are set to different
channels.
PROGRAMMING TEMPERATURE IN CELSIUS OR FAHRENHEIT • Press and hold
MODE button for 3 seconds to toggle the temperature unit in Celsius
(ºC) or Fahrenheit (ºF).
SETTING TEMPERATURE ALARM • Press down button to select temp
display.
• Press TEMP ALARM button selecting the desired alarm, the upper
temperature alert with icon (if disabled, displays OFF), or lower
temperature alert with icon (if disabled, displays OFF).
• Press and hold TEMP ALARM button until the temperature digits
flashing.
• Adjust the temperature digits using the UP (? ) or DOWN (? ).
Press and hold either button for fast digits advance
• Press the TEMP ALARM to confirm selection and return to the
temperature alarm selection screen
ACTIVATING OR DEACTIVATING TEMPERATURE ALARMS • Once the above
alerts are displayed, press the UP (? ) or DOWN (? ) to enable or
disable the corresponding alert.
11
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button
recalling: • Current temperature and humidity • Minimum temperature
and humidity • Maximum temperature and humidity at the remote
location.
Indicator displayed
20°C to 25°C (68°F to 77°F)
40%RH- 70%RH
-5°C to 50°C (23°F to122°F)
OVER 70%RH
Contains excess moisture
BELOW 40%RH
Contains inadequate moisture
RESETTING TEMPERATURE MEMORIES Press and hold MEMORY button for 3
seconds to clear all channel memories.
COMFORT LEVEL INDICATION The main unit is capable of detecting and
displaying the current indoor comfort levels of surrounding
environment. The comfort level based on the combination of the
current indoor temperature and humidity readings. The following
comfort levels may be displayed: COMFORT (comfortable); WET (wet)
and DRY (dry)
CLOCK WINDOW
WWVB RADIO CONTROLLED TIME The NIST (National Institute of
Standards and Technology) radio station (WWVB) is located in Ft.
Collins, Colorado. It transmits an exact time signal continuously
throughout the most of the continental United States at 60 KHz
frequency. The main unit can receive this WWVB signal through the
internal antenna from up to 2,000 miles away. Due to the nature of
the Earth’s ionosphere, reception can be limited during the
daylight hours. The radio controlled clock will search for an
alternate station that receives the atomic time signal from the
NIST Atomic clock in Boulder, Colorado.
The WWVB tower icon on the unit’s display will flash indicating a
radio signal reception from the WWVB station. If the tower icon is
not fully lit, or if the time and date are not set automatically,
please consider the following:
• During nighttime hours, atmospheric disturbances are typically
less severe and radio signal reception may improve. A single daily
reception is sufficient enough to keep the clock accuracy within 1
second.
• Make sure the unit is positioned at 8 feet (2 meters) distance
from any interference source such as a TV, computer monitor,
microwave, etc.
• Within concrete wall rooms such as basements or office buildings,
the received signal may be weakened. Always place the main unit
near the window for better reception.
Once the atomic time signal is received, the date and time will be
set automatically, and the [ ] icon will appear.
12
Undefined data(Flashing)
Weak signal, but can be decoded
Strong signal
• The atomic clock receiver is programmed that it will search for
the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00
am.
• To enable or disable the atomic time receiver, press and hold UP
(? ) button for 3 seconds. If atomic time reception is activated, a
tower icon will start flashing. If reception is disabled, the tower
icon will disappear.
• If the time signal has not been received in 8 minutes, you may
set the time manually. (Refer to the MANUAL SETTINGS
section).
MANUAL SETTINGS To select the time mode, press UP (? ) or DOWN (? )
until the IN icon flashing with a beep sound alert. It is necessary
to set the desired US TIME ZONE.
TIME ZONE • Press MODE button once to select hour and minutes with
the day of the week display.
• Select the Time Zone by pressing and holding UP (? ) button for 3
seconds.
• Keep holding UP (? ) button until the desired US Time Zone
(Pacific, Mountain, Central or Eastern) is highlighted on the
display’s US map, located to the right of the time display and
above the day of the week.
• Release the UP (? ) button. The Time Zone is set.
TIME AND CALENDER • Press and hold MODE button until the day of
week language abbreviation “ENG” will flash
• Press the UP (? ) or DOWN (? ) selecting the day of the week in
English, German, French, Italian, Spanish, Dutch or Swedish.
• After the language of weekday is MODE, press MODE button to
confirm and move to the next parameter (year).
• Continue setting the year, month, day, time format (12 or 24
hours), local hour and minutes, using the same technique.
• After programming is complete the display will return to the
default hour and minutes with seconds display.
13
CLOCK ALARMS There are two time alarms – Weekday alarm (W) and
Single day alarm (S) - and one Ice Warning Alarm (PRE-AL). • If
Weekday (W) alarm is activated, it will sound at the set time and
the alarm icon will flash Mondays through Fridays • If Single (S)
day alarm is activated, it will sound at the set time and the alarm
icon will flash only for this specific day and will not activate on
subsequent days • If Ice Warning Alarm ( PRE-AL) is activated, it
will sound at the set time and alarm icon will flash when the
remote temperature for Channel One (1) reaches 32°F(0°C) and
below.
NOTE: Ice Warning Alarm can be set only if weekday and/or the
single alarm are programmed.
SETTING THE WEEKDAY (W) AND SINGLE DAY (S) ALARMS • Press ALARM
button once to enter into the alarms setting mode. The default
alarm is a Weekday alarm (W). The abbreviation “OFF” with a letter
“W” next to it will be displayed, if the alarm has not been set
previously
• Press and hold ALARM button for two seconds. The hour digit will
flash • Adjust the hour using UP ( ? ) or DOWN ( ? ) buttons
• Press ALARM button again. The minute digits will flash
• Adjust the minutes using UP (? ) or DOWN (? ) buttons
• Press ALARM button again to confirm and the weekday alarm time
will be set
• Set Single (S) day alarm if desired in the same manner
SETTING THE ICE WARNING ALARM (PRE-AL) If Weekday (W) or Single day
(S) alarm is set, the Ice Warning Alarm (Pre-AL) can be
programmed.
• Press ALARM button once to enter into the Ice Warning Alarm
setting mode. The abbreviation OFF with a PRE-AL next to it will be
displayed.
• Press and hold ALARM button for two seconds. The number 30 will
flash, meaning that if selected, the alarm will sound 30 minutes
earlier than the Weekday or Single alarm.
• Select the desired Ice Warning Alarm interval in 15 minutes
increments between 15 and 90 minutes, using UP (? ) or DOWN (? )
buttons
• Press ALARM button to confirm and exit from the alarm setting
mode.
ACTIVATING/ DEACTIVATING ALARMS • Press ALARM button to enter into
the desired alarm mode.
• Press UP ( ? ) to activate alarm and the corresponding icons W, S
or PRE-AL will be displayed.
• Press DOWN ( ? ) to deactivate alarm until “OFF” is
displayed.
MAINTANANCE CHANGING BATTERIES
• If the low battery indicator lights up, replace batteries in the
corresponding unit.
• Do not mix old and batteries.
CLEANING The main unit and remote sensors housings can be cleaned
with a damp cloth. Small parts can be cleaned with a cotton tip or
pipe-cleaner. Never use abrasive or corrosive cleaning agents or
solvents. Do not immerse electronic components in water.
14
Issue
Cannot locate remote sensor
Cannot change the channel
Place unit by the window and keep it there overnight
Check batteries
Check location
Press and hold DOWN ( ? ) button on the main unit to search for the
signal form the remote sensor
Press “RESET” after setting the channel
Initiate manual sensor search (Press and hold DOWN ( ? ) button on
the main unit)
Remote sensor
Symptom Solution
PRECAUTIONS This product is engineered to give you years of
satisfactory service if handled carefully. Here are a few
precautions:
• Do not immerse the units in water.
• Do not clean the units with abrasive or corrosive materials. They
may scratch the plastic parts and corrode the electronic
circuits.
• Do not subject the product to excessive force, shock, dust,
temperature, or humidity, which may result in malfunctions, shorter
lifespan, damaged batteries, and damaged parts.
• Do not tamper with the units internal components. Doing so will
invalidate the warranty and may cause damage. These units contain
no user-serviceable parts.
• Use only fresh batteries. Do not mix new and old batteries. •
Read the user's manual thoroughly before operating the units.
TROUBLESHOOTING
15
Meade Instruments Corp. 27 Hubble Irvine, CA 92618 U.S.A.
©2011 Meade Instruments Corp. All Rights Reserved. All user manual
contents and information are subject to change.
<< /ASCII85EncodePages false /AllowTransparency false
/AutoPositionEPSFiles true /AutoRotatePages /None /Binding /Left
/CalGrayProfile (Dot Gain 20%) /CalRGBProfile (sRGB IEC61966-2.1)
/CalCMYKProfile (U.S. Web Coated \050SWOP\051 v2) /sRGBProfile
(sRGB IEC61966-2.1) /CannotEmbedFontPolicy /Error
/CompatibilityLevel 1.4 /CompressObjects /Tags /CompressPages true
/ConvertImagesToIndexed true /PassThroughJPEGImages true
/CreateJDFFile false /CreateJobTicket false /DefaultRenderingIntent
/Default /DetectBlends true /ColorConversionStrategy
/LeaveColorUnchanged /DoThumbnails false /EmbedAllFonts true
/EmbedJobOptions true /DSCReportingLevel 0 /EmitDSCWarnings false
/EndPage -1 /ImageMemory 1048576 /LockDistillerParams false
/MaxSubsetPct 100 /Optimize true /OPM 1 /ParseDSCComments true
/ParseDSCCommentsForDocInfo true /PreserveCopyPage true
/PreserveEPSInfo true /PreserveHalftoneInfo false
/PreserveOPIComments false /PreserveOverprintSettings true
/StartPage 1 /SubsetFonts true /TransferFunctionInfo /Apply
/UCRandBGInfo /Preserve /UsePrologue false /ColorSettingsFile ()
/AlwaysEmbed [ true ] /NeverEmbed [ true ] /AntiAliasColorImages
false /DownsampleColorImages true /ColorImageDownsampleType
/Bicubic /ColorImageResolution 300 /ColorImageDepth -1
/ColorImageDownsampleThreshold 1.50000 /EncodeColorImages true
/ColorImageFilter /DCTEncode /AutoFilterColorImages true
/ColorImageAutoFilterStrategy /JPEG /ColorACSImageDict <<
/QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >>
/ColorImageDict << /QFactor 0.15 /HSamples [1 1 1 1]
/VSamples [1 1 1 1] >> /JPEG2000ColorACSImageDict <<
/TileWidth 256 /TileHeight 256 /Quality 30 >>
/JPEG2000ColorImageDict << /TileWidth 256 /TileHeight 256
/Quality 30 >> /AntiAliasGrayImages false
/DownsampleGrayImages true /GrayImageDownsampleType /Bicubic
/GrayImageResolution 300 /GrayImageDepth -1
/GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true
/GrayImageFilter /DCTEncode /AutoFilterGrayImages true
/GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict <<
/QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >>
/GrayImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples
[1 1 1 1] >> /JPEG2000GrayACSImageDict << /TileWidth
256 /TileHeight 256 /Quality 30 >> /JPEG2000GrayImageDict
<< /TileWidth 256 /TileHeight 256 /Quality 30 >>
/AntiAliasMonoImages false /DownsampleMonoImages true
/MonoImageDownsampleType /Bicubic /MonoImageResolution 1200
/MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000
/EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode
/MonoImageDict << /K -1 >> /AllowPSXObjects false
/PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false
/PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000
0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true
/PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ]
/PDFXOutputIntentProfile () /PDFXOutputCondition ()
/PDFXRegistryName (http://www.color.org) /PDFXTrapped /Unknown
/Description << /ENU (Use these settings to create PDF
documents with higher image resolution for high quality pre-press
printing. The PDF documents can be opened with Acrobat and Reader
5.0 and later. These settings require font embedding.) /JPN
<FEFF3053306e8a2d5b9a306f30019ad889e350cf5ea6753b50cf3092542b308030d730ea30d730ec30b9537052377528306e00200050004400460020658766f830924f5c62103059308b3068304d306b4f7f75283057307e305930023053306e8a2d5b9a30674f5c62103057305f00200050004400460020658766f8306f0020004100630072006f0062006100740020304a30883073002000520065006100640065007200200035002e003000204ee5964d30678868793a3067304d307e305930023053306e8a2d5b9a306b306f30d530a930f330c8306e57cb30818fbc307f304c5fc59808306730593002>
/FRA
<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>
/DEU
<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>
/PTB
<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>
/DAN
<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>
/NLD
<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>
/ESP
<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>
/SUO
<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>
/ITA
<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>
/NOR
<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>
/SVE
<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>
>> >> setdistillerparams << /HWResolution [2400
2400] /PageSize [612.000 792.000] >> setpagedevice