TASKI%20R2

1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER

29 Chifley St, Smithfield, NSW, AUSTRALIA, 2164

(02) 9757 0300

Address

Telephone

Emergency

Email

1800 033 111 (24 hrs)

Fax (02) 9725 5767

[email protected]

http://www.johnsondiversey.comWeb Site

Supplier Name JOHNSONDIVERSEY AUSTRALIA PTY LTD

TASKI R2PRODUCT NAME

GENERAL PURPOSE SURFACE CLEANERUse(s)

Synonym(s) 7509655 TASKI R2 6X750ML • HH14325 TASKI R2 2X5L

MSDS Date 26 September 2007

NOT CLASSIFIED AS HAZARDOUS ACCORDING TO NOHSC CRITERIA

2. HAZARDS IDENTIFICATION

NOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODE

None Allocated None Allocated None Allocated


UN No.

Pkg Group

DG Class

Hazchem Code

Subsidiary Risk(s)

EPG

3. COMPOSITION / INFORMATION ON INGREDIENTS

Ingredient Formula CAS No. ContentWATER H2O 7732-18-5 >60%NONIONIC SURFACTANT(S) Not Available Not Available <5%

Eye Flush gently with running water for 15 minutes.

Skin Remove contaminated clothing and gently flush affected areas with water. Seek medical attention if irritationdevelops. Launder clothing before reuse.

Inhalation If over exposure occurs leave exposure area immediately. If irritation persists, seek medical attention.

Ingestion DO NOT induce vomiting. Immediately wash out mouth with water, and then give water to drink. Seek medicalattention.

Advice to Doctor Treat symptomatically

First Aid Facilities Eye wash facilities and safety shower are recommended.

4. FIRST AID MEASURES

Fire andExplosion

Non flammable. Evacuate area and contact emergency services. Remain upwind and notify those downwind ofhazard. Wear full protective equipment including Self Contained Breathing Apparatus (SCBA) when combatingfire. Use waterfog to cool intact containers and nearby storage areas.

Extinguishing Non flammable.

Flammability Non flammable. No fire or explosion hazard exists.

5. FIRE FIGHTING MEASURES

Page 1 of 4

Reviewed: 26 Sep 2007

Printed: 26 Sep 2007

RMT

PRODUCT NAME TASKI R2

Hazchem Code None Allocated

Spillage If spilt (bulk), wear splash-proof goggles, PVC/rubber gloves, coveralls and rubber boots. Absorb spill with sand orsimilar, collect and place in sealable containers for disposal. Prevent spill entering drains or waterways. Caution:Slippery when spilt.

Handling

Store in cool, dry area, removed from foodstuffs. Ensure containers are labelled, protected from physical damageand sealed when not in use.

Storage

Before use carefully read the product label. Use of safe work practices are recommended to avoid eye or skincontact and inhalation. Observe good personal hygiene, including washing hands before eating. Prohibit eating,drinking and smoking in contaminated areas.

6. ACCIDENTAL RELEASE MEASURES

7. STORAGE AND HANDLING

8. EXPOSURE CONTROLS / PERSONAL PROTECTIONExposureStandards

No exposure standard(s) allocated.

No biological limit allocated.Biological LimitValues

EngineeringControls

Ensure adequate natural ventilation.

PPE Wear splash-proof goggles and rubber or PVC gloves. When using large quantities or where heavy contaminationis likely, wear coveralls.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance GREEN LIQUID Solubility (water) SOLUBLE

Odour CHARACTERISTIC ODOUR Specific Gravity 1.00

pH 11.5 (neat) % Volatiles NOT AVAILABLE

Vapour Pressure NOT AVAILABLE Flammability NON FLAMMABLE

Vapour Density NOT AVAILABLE Flash Point NOT RELEVANT

Boiling Point 100°C (Approximately) Upper Explosion Limit NOT RELEVANT

Melting Point NOT AVAILABLE Lower Explosion Limit NOT RELEVANT

Evaporation Rate NOT AVAILABLE Autoignition Temperature NOT AVAILABLE

10. STABILITY AND REACTIVITY

Material to Avoid Compatible with most commonly used materials.

Decomposition May evolve toxic gases if heated to decomposition.

Health HazardSummary

This product may only present a hazard with direct eye contact or with prolonged and repeated skin contact. Nochronic effects are anticipated with normal use.

Eye Exposure may result in irritation and lacrimation.

Inhalation Over exposure at high levels may result in mucous membrane irritation of the nose and throat with coughing.

Skin Prolonged and repeated contact may result in irritation, skin rash and dermatitis.

Ingestion With large doses ingestion may result in nausea, vomiting and gastrointestinal irritation.

Toxicity Data No LD50 data available for this product.

11. TOXICOLOGICAL INFORMATION

Page 2 of 4



RMT


Environment This product is not anticipated to cause adverse effects to animal or plant life if released to the environment insmall quantities. Not expected to bioaccumulate.

12. ECOLOGICAL INFORMATION

Waste Disposal For small amounts, absorb with sand or similar and dispose of to an approved landfill site. Contact themanufacturer for additional information. Ensure that appropriate personal protective equipment is used duringdisposal.

Legislation Dispose of in accordance with relevant local legislation.

13. DISPOSAL CONSIDERATIONS

14. TRANSPORT INFORMATION

NOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODE



Shipping Name

UN No.

Pkg Group

DG Class

Hazchem Code

Subsidiary Risk(s)

EPG

None Allocated

Poison Schedule A poison schedule number has not been allocated to this product using the criteria in the Standard for the UniformScheduling of Drugs and Poisons (SUSDP).

AICS All chemicals listed on the Australian Inventory of Chemical Substances (AICS).

15. REGULATORY INFORMATION

AdditionalInformation

ABBREVIATIONS:ADB - Air-Dry Basis.CAS# - Chemical Abstract Service number - used to uniquely identify chemical compounds.CNS - Central Nervous System.IARC - International Agency for Research on Cancer.M - moles per litre, a unit of concentration.mg/m3 - Milligrams per cubic metre.NOS - Not Otherwise Specified.pH - relates to hydrogen ion concentration using a scale of 0 (high acidic) to 14 (highly alkaline).ppm - Parts Per Million.TWA/ES - Time Weighted Average or Exposure Standard.

PERSONAL PROTECTIVE EQUIPMENT GUIDELINES:The recommendation for protective equipment contained within this Chem Alert report is provided as a guide only.Factors such as method of application, working environment, quantity used, product concentration and theavailability of engineering controls should be considered before final selection of personal protective equipment ismade.

HEALTH EFFECTS FROM EXPOSURE:It should be noted that the effects from exposure to this product will depend on several factors including: frequencyand duration of use; quantity used; effectiveness of control measures; protective equipment used and method ofapplication. Given that it is impractical to prepare a Chem Alert report which would encompass all possiblescenarios, it is anticipated that users will assess the risks and apply control methods where appropriate.

16. OTHER INFORMATION

Report Status This document has been compiled by RMT on behalf of the manufacturer of the product and serves as themanufacturer's Material Safety Data Sheet ('MSDS').

It is based on information concerning the product which has been provided to RMT by the manufacturer orobtained from third party sources and is believed to represent the current state of knowledge as to the appropriatesafety and handling precautions for the product at the time of issue. Further clarification regarding any aspect ofthe product should be obtained directly from the manufacturer.

While RMT has taken all due care to include accurate and up-to-date information in this MSDS, it does not provideany warranty as to accuracy or completeness. As far as lawfully possible, RMT accepts no liability for any loss,

Page 3 of 4



RMT


injury or damage (including consequential loss) which may be suffered or incurred by any person as aconsequence of their reliance on the information contained in this MSDS.

Prepared By Risk Management Technologies5 Ventnor Ave, West PerthWestern Australia 6005Phone: +61 8 9322 1711Fax: +61 8 9322 1794Email: [email protected]: www.rmt.com.au

End of Report26 September 2007MSDS Date:

Page 4 of 4



RMT

Documents

TASKI%20R2