Table of Contents

Preface

Plenary

Recent Developments in the Processing of Advanced Materials Using Severe PlasticDeformationM. Kawasaki, R.B. Figueiredo and T.G. Langdon 3

Keynotes

Achieving Superplasticity in Fine-Grained Al-Mg-Sc AlloysP.H.R. Pereira, Y. Huang, M. Kawasaki and T.G. Langdon 11Improvement in Mechanical Performance of Biomaterial Ti Alloy by Controlling VolumeFraction of Martensite PhaseT. Akahori, S. Ino and T. Hattori 18Additive Manufacturing of Ti6Al4V with Wire Laser Metal Deposition ProcessA. Ayed, G. Bras, H. Bernard, P. Michaud, Y. Balcaen and J. Alexis 24Model Description of the Unusual Temperature Dependence of the Viscosity of MetallicGlass-Forming LiquidsM. Aniya and M. Ikeda 30Mechanical Stress Issues of La0.6Sr0.4Co0.2Fe0.8O3-δW. Araki and Y. Arai 36Effects of Al, Si and N Content on the Formation of M-A Constituent and HAZ Toughnessof Ti-Containing Low-Carbon SteelK.S. Bang, J.H. Cha, K.T. Han and H.C. Jeong 42Grain Orientation Spread in Dynamically Recrystallized Austenitic SteelA. Belyakov, V. Torganchuk, O.V. Rybalchenko, S.V. Dobatkin and R. Kaibyshev 50Effect of the Morphology, Size, Distribution and Homogeneity of Carbides and Matrix onWear Resistance in High Cr-Alloys White Cast IronC. Camurri, J. Maril and E. Romero 56Friction Stir Welded AISI 304 Metal Sheets for Application in Food ImplantsE. Cerri, A. Pirondi and J.P. Bergmann 63The Use of Transient Liquid Phases in Powder MetallurgyH. Danninger, R. de Oro Calderon and C. Gierl-Mayer 69Austenitic Grain Size Effect on the Phase Transformation of a 7.0% Cr Steel for ForgingR. Coletti, A. di Schino, S. Mengaroni and S. Neri 77Evolution of Carbides during Prestrain and TemperingW.H. Ding, B. Jiang, C.L. Zhang, Y.Z. Liu, L. Sun, T.W. Liu, Z.Q. Zhang and J. Pan 82Detonation Spraying of Metal Carbides CompositesV. Ulianitsky, A. Shtertser, I. Batraev, M. Doubenskaia and I. Smurov 88How to Master Interfaces in MMCs with Reactive ConstituentsC. Edtmaier 94Synchrotron 3D μ-Tomography of Porosity during Hot Isostatic Pressing of a Single-CrystalNickel-Base SuperalloyA. Epishin, B. Camin, L. Hansen and J. Schmidt 102Evaluation of Cu-Ni-Based Alloys for Thermoelectric Energy ConversionT. Steinhoff, M. Wolf, F. Nürnberger, G. Gerstein and A. Feldhoff 107Mechanical and Thermal Properties of Harmonic Structured Composites by MM/SPSProcessH. Fujiwara 113Time-, Temperature- and Frequency-Dependent Viscoelastic Properties of a Curing EpoxyAdhesiveP.L. Geiss and M. Schumann 119

THERMEC 2021THERMEC 2021THERMEC 2021THERMEC 2021ISBN(softcover): 978-3-0357-1630-6 ISBN(eBook): 978-3-0357-3630-4

Fatigue Behavior of Age-Hardening Cu-6Ni-1.5Si Alloys with Different Grain SizesM. Goto, T. Yamamoto, S.Z. Han, J. Kitamura, J.H. Ahn, S.H. Lim, S.J. Lee, T. Utsunomiya andJ. Lee 125Processing Strategies for Hot-Rolled Medium-Mn SteelsA. Grajcar, S. Adam and M. Morawiec 132Development and Characterization of New Ti-25Ta-Zr Alloys for Biomedical ApplicationsP.A.B. Kuroda, F.d.F. Quadros, M.V. Nascimento and C.R. Grandini 137Effect of Microshot Peening on Fatigue Strength of Austenite Stainless SteelY. Harada and K. Takahashi 145Mechanical Properties of Interface Layers in SiC/TiAl CompositeK. Hashimoto and J. Jin 151Inferences of Baking Time on Hydrogen Embrittlement for High Strength Steel Treatedwith Various Zinc Based ElectroplatingM. Hino, S. Mukai, T. Shimada, K. Okada and K. Horikawa 156Influence of Substitution of Fe by Mo on Heat Treatment Behavior in Ti-Mo-Fe AlloysK. Mizuta, S. Miyake, M. Ikeda and M. Ueda 162Layer-Thickness Dependence of Hardness and Local Bucking Behavior in ElectrodepositedNi-Co-Cu/Cu Multilayered FilmsY. Kaneko, T. Kubomae, N. Kawakami, H. Hagiwara and M. Uchida 170Hardness Development of Mechanically-Bonded Hybrid Nanostructured Alloys throughHigh-Pressure TorsionM. Kawasaki and T.G. Langdon 177Energy Absorption of Additively Manufactured Porous Metals with Disordered CellsK. Kitazono, S. Guo, K. Zhu, T. Hamaguchi and Y. Fujimori 183Experimental Characterization and Modelling of the PLC Effect in an AlMg-AlloyJ.B. Xu, B. Holmedal, O.S. Hopperstad and K. Marthinsen 188Influence of Strain-Hardening and Dynamic Recovery on DDRX Steady StateF. Montheillet and D. Piot 194Ultrasonic Processing of Magnesium Alloy for Property EnhancementP. Emadi, E. Vandersluis, B. Andilab, M. Rinaldi and C. Ravindran 200Computer Prediction of Phase Fraction in Multipass Weld of Duplex Stainless Steel -Proposal of Microstructural Improvement Welding Process -K. Saida, T. Ogura, S. Yamashita and Y. Oikawa 206Effect of Particle Morphology on Thermal Properties of TiB2 Particle Dispersed PureAluminum CompositesG. Sasaki 213Development of New Particle Method Based on MPS and its Applicability for Friction StirWelding of Dissimilar JointH. Serizawa, K. Mitsufuji and F. Miyasaka 218

Contributions

Corrosion Resistance of Additive Manufactured Titanium Alloy Parts: The Effect ofRecycled PowdersA. Acquesta and T. Monetta 225PL Properties of (Ba, Ca)2( Si, P)O4: Eu Synthesized by Various Annealing and CoolingProcessS. Ando, H. Nakano and K. Fukuda 231Microstructural Prediction of Heat Treated Steel Forgings for Severe ApplicationsE. Anelli, M. Lucchesi and A. Chugaeva 236Influence of Elastic Modulus of Matrix on Conductivity of VGCF Dispersed in PlasticMatrixT. Aoki, N. Nakayama, M. Horita and H. Fukui 243Study of the Impact of the Synergic Line and the Strategy of Conception on Ti-6Al-4V WireArc Additive Manufacturing Process (WAAM-CMT)A. Ayed, G. Bras, H. Bernard, P. Michaud, Y. Balcaen and J. Alexis 250

b THERMEC 2021

Thermomechanical Processing without Accelerated Cooling to Achieve an As-Rolled YieldStrength of 400MPa in C-Mn Steel PlateK.M. Banks, R. Maubane and M. Coleman 25615/15 Ti Stainless Steel Welding Process Optimization for GEN IV Nuclear Application inthe GEMMA Project FrameG. Barbieri, F. Cognini, L. Pilloni, D.M. Gattia and C. Testani 262High Cycle Fatigue Behaviour of Cu/Sn Intermetallic Compounds Prepared by TransientLiquid Phase Bonding ProcessA.B. Kotas, G. Khatibi, F. Khodabakhshi and A. Steiger-Thrisfeld 268Thermal and Magnetic Properties of Ternary Fe-B-C and Quaternary Fe-B-C-Si Alloyswith High Glass-Forming Ability and High MagnetizationT. Bitoh, T. Hibino and H. Koshiba 274Adaption of 3D Printing for Rapid ToolingA. Böhme, D. Nemak, F. Schütze, K.H. Lietzau, E. Wolf and A.H. Foitzik 280High Purity Magnetite Microparticles Directly Derived from Mill Scale via Hydrogen-Reduction MethodA. Boontanom and P. Suwanpinij 286Fracture Behavior of an AlMgMnSc Alloy at Different TemperaturesY.I. Borisova, D. Yuzbekova and A. Mogucheva 292Multi-Scale Characterization by Neutronography and Electron Diffraction of Ni Coating onCu-Ni-Al or Cast-Iron Glass Molds after Laser CladdingF. Bourahima, A.L. Helbert, F. Ott, V. Ji, M. Rege, F. Brisset, A. Courteaux and T. Baudin 297Design Solutions from Material Selection for Rib FixatorsJ.L. Arreguin, R. Montanari, M. Ceccarelli, V. Ambrogi, M. Richetta, C.R. Torres-San-Migueland A. Varone 303Effect of Distance along the Built Axis on Mechanical Properties and Microstructure inAl10SiMg SLM AlloyE. Cerri and E. Ghio 309Martensitic Transformation and Damping Behavior of Fe-Mn-Nb Damping AlloysF. Chen, F.K. Liang, W.L. Ye, Y.X. Tong and L. Li 315Hot and Cold Deformation Behaviors and Microstructure Evolutions of Mn18Cr18NAustenitic Stainless Steel with High-NitrogenH.Q. Chen, J.H. Tian, F. Li, F.M. Qin and W.W. He 325Microstructure Evolution in an Advanced High Strength Steel under Continuous CoolingS.P. Chen, R. Mostert and M. Aarnts 332Thermal Stability of Ultrafine-Grained Pure Titanium Processed by High-Pressure TorsionW.J. Chen, J. Xu, D.T. Liu, D.B. Shan, B. Guo and T.G. Langdon 338Study on the Effect of V Microalloying on Earthquake Resisting High-Strength ReinforcingBar SteelsJ. Chung, T.Y. Kim and J.S. Lee 345Change of Microstructure and Analysis of Fracture of the Ti-50.8 at.% Ni Alloy in theUltrafine-Grained State after Multiple Martensitic Transformations with a Large Numberof CyclesA. Churakova and D. Gunderov 354Effect of Different Production Processes on Metallic Composite Phase Change Materials forThermal Energy StorageC. Confalonieri and E. Gariboldi 359Extended Model for Prediction of Transition from Internal to External Oxidation in Steels:Comparison between Analytical/Semi-Analytical and Numerical ApproachesI. Darghoum, J. Leblond, D. Huin, J. Bergheau and F. Bertrand 366Challenges in Printing Certified Additive Manufactured Material: Ensuring ProcessStability and Material QualityE. de Bruycker, C. Hautfenne, F. Thielemans and S. Nardone 372Influence of Mn and Ni on Austenite Stabilization during a High Temperature Q&PTreatmentE. Del Molino, T. Gutierrez, M. Serna-Ruiz, M. Arribas and A. Arlazarov 379Changes in Mechanical and Microstructural Properties of Magnesium Alloys Resultingfrom Superimposed High Current Density PulsesE. Demler, A. Diedrich, A. Dalinger, G. Gerstein, S. Herbst, S. Zaefferer and H.J. Maier 385

Materials Science Forum Vol. 1016 c

Revisiting the Ostwald Ripening: A Discrete Model Based on Multiple Pairwise InteractionsP.E. di Nunzio 392Mechanical Properties of Selective Laser-Melted Components of Alsi10mg for PrototypeVehiclesC. Egger, F. Grünbart, Z. Silvayeh, O. Šulcová, C. Seper, T. Pfeifer, C. Sommitsch and J.Domitner 399The Isothermal Oxidation of MCrAlY Protective CoatingsM. Drajewicz, T. Kubaszek, B. Kościelniak, M. Góral and D. Dziadosz 407Delamination of Pearlitic Steel Wires: Role of Strain Partition on Mechanical Properties ofPearlitic WiresA.D.V. Prasad and S. Mukherjee 413Evolution of the Microstructure and Mechanical Properties of the Ultrafine-GrainedVT8M-1 during Isothermal Die Forging and Thermal TreatmentG. Dyakonov, T.V. Yakovleva, A. Stotskiy, A. Ibatullin and I. Semenova 418Statistical Errors in X-Ray Triaxial Stress Analysis by Cos α MethodS. Ejiri, H. Ohba and T. Sasaki 423Thermal Stability of Retained Austenite in Advanced TRIP Steel with Bainitic FerriteMatrix for Automotive IndustriesE. El-Shenawy, H. Refaiy and H. Nasr El-Din 4293d Printer Heads for Extrusion of Biologicals GelsA. Engels, V. Schlegel, H. Jacobs, N. Großelindemann, N. Morshed, A. Stenglein, V. Bonaiutoand A.H. Foitzik 435Influence of Surface Roughness on the Corrosion Behaviors of DP590 SteelB.Y. Fang 440Hot Stamped Aluminium for Crash-Resistant Automobile Safety Cage ApplicationsJ. Pujante, D. Frómeta, E. Garcia-Llamas, M. Gimenez and D. Casellas 445Performance of Vibration Power Generators Using Single Crystal and Polycrystal MagneticCores of Fe–Ga AlloysS. Fujieda, N. Gorai, T. Kawamata, R. Simura, T. Fukuda and S. Suzuki 453Biocompatibility of Anodized Low-Cost Ti-4.7Mo-4.5Fe AlloyY. Abdelrhman, S. Kobayashi, S. Okano, T. Okamoto and M.A. Gepreel 458Effect of Thermomechanical Treatments on the Mechanical Properties of New Low-Cost Ti-Fe-Nb-Zr AlloysM.A. Gepreel and M. Niinomi 465Tailored Liquid Phases for Enhanced Sintering of Advanced PM - SteelsS. Geroldinger, R. de Oro Calderon, C. Gierl-Mayer and H. Danninger 470Aging Response in Selective Laser Melted AlSi10Mg Alloy as Function of Distance from theSubstrate PlateE. Ghio and E. Cerri 476Fracture Toughness and Fatigue Crack Growth Characteristics of UFG Microalloyed andIF Steels Processed by Critical Phase Control Multiaxial ForgingS. Ghosh, S. Mula, M. Somani and J. Kömi 481Thermal Barrier Coatings for Molybdenum Produced Using NanopowdersM. Góral, T. Kubaszek, M. Drajewicz and P. Borowski 487Increasing Hardenability and Hardness of Quenching and Tempering Alloys bySubstituting Chromium with ManganeseA. Gramlich, F. Pape, G. Heßling and W. Bleck 493Multi-Class Grain Size Model for Forged Alloy 718 Aircraft PartsC. Gruber, P. Raninger, M. Stockinger and C. Bucher 499Non-Vacuum Fabrication of Bandgap-Controlled CZTGS Alloy Films Using CZTS+CZGSMixed Nanoparticle InksY. Hamanaka and K. Matsumoto 509Tensile Deformation Behavior of Magnesium Single Crystals with Different YttriumConcentrationsT. Hanada, M. Tsushida, H. Kitahara and S. Ando 516Brazing of Stainless Steel Using Electrolytic Ni-P Plating Film and Investigation ofCorrosion BehaviorA. Hashimoto, S.B. Liu, I. Shohji, T. Kobayashi, J. Hirohashi, T. Wake, S. Arai and Y.Kamakoshi 522

d THERMEC 2021

Shear Banding in Rotated Goss Grains and its Effect on the Formation of Cube Texture inNon-Oriented Electrical SteelY.L. He, M. Mehdi, E.J. Hilinski, T. Zhou, P. Badgley, L.A.I. Kestens and A. Edrisy 528Micromechanical Simulation Approach of Dual Phase Steel Artificial Microstructure UsingRandom Field ModelM.I.E. Heddar, N. Matougui and B. Mehdi 534Orthotropic Behaviour of Magnesium AZ31 Sheet during Strain LocalizationT. Henseler, M. Ullmann and U. Prahl 541Microstructure and Tensile Properties of Sn-Ag-Cu-In-Sb SolderY. Hirai, K. Oomori, H. Morofushi and I. Shohji 553Iron Carbon Masteralloy as Sintering Activator for Low Alloy Powder Metallurgy SteelsM. Hojati, C. Gierl-Mayer and H. Danninger 561Quantitative Detection of Hydrogen Gas Release during Slow Strain Rate Testing inAluminum AlloysK. Horikawa, M. Arayama and H. Kobayashi 568Effect of Compressive Residual Stress on Film Formed by Mechanochemical MultifunctionCavitation ProcessingM. Ijiri, F. Kato, D. Maeda, D. Shimonishi and T. Yoshimura 574Grain Refinement of Fe-X Alloys Fabricated by Laser Powder Bed FusionH. Ikehata and E. Jägle 580The Influence of Introduced Strains on the Exfoliation Corrosion Behavior of Mg-14mass%Li-1mass%Al AlloyH. Ikoma, T. Morishige and T. Takenaka 587Corrosion Resistance of Mg Alloy with High Zn Concentration Including Impurity CuM. Ikoma, T. Morishige, T. Kikuchi, R. Yoshida and T. Takenaka 592Optimization of Slab Edge in Roughing of Stainless SteelJ. Ilmola, O. Seppälä, O. Haapala, E. Puukko and J. Larkiola 598Orientation AnalysisJ. Imhof 605Parametric Study of Pulse Arc Welding (PAW) and Laser Beam Welding (LBW)Techniques for Electrical Vehicle Battery CellsN. Iqbal, S. Nath, A.E. Coleman and J. Lawrence 611Post-Fire Performance of Square Concrete-Filled Steel Tube Columns under Uni-AxialLoadJ. Thumrongvut, A. Tipcharoen and K. Prathumwong 618Promising Bendability of a New As-Rolled Medium-Carbon, Low-Alloy Steel withIsothermal Upper and Lower Bainitic MicrostructureV. Javaheri, A. Kaijalainen, S. Pallaspuro, D. Porter and J.I. Kömi 624Study on Forging Permeability of 06Cr19Ni9NbN Steel during Hot DeformationY.X. Jiao, J.S. Liu and X.Z. Zhang 630Influence of Chromium and Niobium on the Press-Hardening Process of Multiphase Low-Alloy TRIP SteelsH. Jirková, J. Vrtáček, M. Peković, T. Janda and L. Kučerová 636Optimising Computational Fluid Dynamic Conditions for Simulating Copper VerticalCastingT.D.A. Jones, R.I. Strachan, D.M. Mackie, M. Cooper, B. Frame and J.B. Vorstius 642Improvement on Impact Toughness of Cold Formed S420 Steel by Direct QuenchingA. Kaijalainen, J. Mourujärvi, J. Tulonen, P. Steen and J.I. Kömi 648Effect of Cooling Rate below Ms Temperature on Hydrogen Embrittlement of TRIP-AidedMartensitic SteelsN. Kakefuda, S. Aizawa, R. Sakata, J. Kobayashi, G. Itoh and T. Hojo 654Investigation of Temperature Evolution and Flash Formation at AA5083 Studs duringFriction SurfacingZ. Kallien, L. Rath, A. Roos and B. Klusemann 660Microstructure and Precipitation Studies of Gas Tungsten Arc Welded Haynes 282SuperalloyK. Sivaji and G. Phanikumar 666Carrier Concentration of CeFe2Al10 as a Candidate of Thermoelectric MaterialY. Kawamura, C. Sekine and T. Nishioka 672

Materials Science Forum Vol. 1016 e

Effect of Alloying Element on Mechanical Properties of High Strength Austenitic SteelK. Ueda, D. Izumi, T. Ishida and Y. Murakami 678Magnetic and Mechanical Properties of Fe-Cr-Si-Mo Alloys by MIM ProcessM. Kimura, T. Shimizu and H. Watari 685Structural Changes in Multi Principal Element Alloys in Dependence on the AluminiumContentJ. Kirschner, C. Eisenmenger-Sittner, J. Bernardi, A. Großalber, S. Frank and C. Simson 691Shape Memory Properties of Ti-Ni Shape Memory Alloy / Shape Memory PolymerComposites Using Additive ManufacturingK. Kitamura 697Temperature Increase during Isothermal Forging of Ti-5Al-2Sn-2Zr-4Cr-4Mo Alloy Usinga 1500-Ton Forging PressT. Kitashima, Y. Yoshida and R. Matsumoto 702Synthesis PbFCl-Type Mixed Anion APX(A=Hf, X=S, Se) Superconductors Related withTopological Materials by High-Pressure TechniqueH. Kito, K. Kawashima, K. Iwakiri, T. Nishio, S. Ishida, H. Fujihisa, Y. Gotoh, A. Iyo, H. Ogino,H. Eisaki and Y. Yoshida 708Analysis of the Strain Distribution and Texture Measurements in Asymmetric Rolling (AR)and Asymmetric Accumulative Roll Bonding (AARB)R.P. Godoi, B.D. Zanquetta, J.B. Rubert, R.E. Bolmaro, M.C. Avalos, V.L. Sordi and A.M.Kliauga 715Effect of Heat Treatment on Structure and Properties of Martensite Stainless Steel for Ice-Class Ships Obtained by Direct Laser Deposition MethodO.G. Klimova-Korsmik, R.V. Mendagaliyev, I.A. Tsibulskiy, O.G. Zotov, R.S. Korsmik andN.V. Lebedeva 725Microstructure and Tensile Properties of TRIP-Aided Steel Sheet Subjected to Hot-Rollingand AustemperingJ. Kobayashi, H. Sawayama, N. Kakefuda, G. Itoh, S. Kuraoto and T. Hojo 732Fabrication of Three-Dimensional Microstructure Film by Ni-Cu Alloy Electrodepositionfor Joining Dissimilar MaterialsT. Kobayashi and I. Shohji 738Reaction Sintering of Tial Intermetallic CompoundY. Kohama, M. Kimura, T. Shimizu and H. Watari 744Comprehensive Phase Feld Study on Directionally-Solidified MoSi2/Mo5Si3 Eutectic AlloyC.Q. Zhu, J. Yamamoto, Y. Koizumi, K. Yuge, K. Kishida and H. Inui 749Electron Beam Melting: From Shape Freedom to Material Properties Control at Macro-and MicroscaleA. Koptyug, C. Botero, W. Sjöström, M. Bäckström, L.E. Rännar and A.S. Tremsin 755Temperature-Dependent Mechanical Stability of Retained Austenite inThermomechanically Processed 3Mn SteelA. Kozłowska, A. Grajcar, A. Janik and K. Radwański 762Microstructure and Mechanical Properties of the UFG Magnesium Alloy Mg-1%CaO. Kulyasova, R.K. Islamgaliev, H.C. Lin and H. Yilmazer 768Effect of Microstructure on Joint Strength of Fe/Al Resistance Spot Welding for Multi-Material ComponentsK. Kumamoto, I. Shohji, T. Kobayashi and M. Iyota 774Severe Plastic Deformation of Copper, Binary Cu-Zn Solid-Solution Alloys, and High-Strength Brass by High-Pressure TorsionT. Kunimine 780Structural Characterization of a Biogenic Secretion Extracted from the Tendon orLigament in Rabbits for Artificial Ligament FormationT. Kuzumaki, T. Yamaguchi, K. Shimozaki, J. Nakase and K. Torigoe 786Enhancing High-Temperature Creep Resistance of In Situ TiAl-Based Matrix Composite byLow Volume Fraction of Ti2AlC ParticlesJ. Lapin and K. Kamyshnykova 792Impact of Microstructural Anisotropy of As-Cold-Sprayed Cu Deposits on its AnnealingEffectY.J. Li, Y.K. Wei, X.T. Luo and C.J. Li 798Performance of 14Cr ODS-FeCrAl Cladding Tube for Accident Tolerant FuelJ. Li, S.J. Wu, Y.L. Wang, L.Y. Xiong and S. Liu 806

f THERMEC 2021

Analysis of the Applicability of Effective Thermophysical Properties to Composite PhaseChange MaterialsZ.W. Li and E. Gariboldi 813Long Term Stability Evaluation of Stress Improvement Effect on Ni-Based Alloy Welds byVarious Residual Stress Improvement MethodsL.N. Yu, K. Saida, M. Mochizuki, K. Nishimoto and N. Chigusa 819Inhomogeneous Microstructure and its Thermal Stability of AlSi10Mg Lattice StructureManufactured via Laser Powder Bed FusionM.L. Liu, N. Takata, A. Suzuki and M. Kobashi 826Study of Nb Solubility in Hot Charging ProcessB. López, B. Pereda, F. Bastos and J.M. Rodriguez-Ibabe 832Cold Spraying of IN 718-Ni Composite Coatings: Microstructure Characterization andTribological PerformanceR. Biagi, E. Verna, E. Bemborad, M. Galetto, S. Yin and R. Lupoi 840Defect Reduction and Quality Optimization through the Modelling of Plastic Deformationand Metallurgical EvolutionS. Mancini, P.E. di Nunzio, S. Notargiacomo and L. Langellotto 846Grain Boundary Engineering of Strain-Annealed Hastelloy-XW. Muhammad, D. Wei and É. Martin 852Modelling of Cyclic Delamination Behavior of Thin Multilayered Structures Using GradientElasticity and Damage AccumulationM. Lederer, T. Walter and G. Khatibi 857Effects of Activated Carbon Counter Electrode on Bifacial Dye Sensitized Solar Cells(DSSCs)T.E. Putri, Y. Hao, F.L. Chawarambwa, H. Seo, M.K. Son, K. Kamataki, N. Itagaki, K. Koga andM. Shiratani 863Dynamic Recrystallization Mechanisms of Nickel Niobium Alloys during Hot WorkingN. Matougui, M.L. Fares and D. Piot 869Effect of Stress Gradient on Heat Cycle Fatigue Life Prediction of Solder Joints byRepetitive Bending TestM. Matsushima, K. Endo, T. Kawazoe, S. Fukumoto and K. Fujimoto 875Effect of Strain Rate on the Microstructure and β-Texture Evolutions in β-ProcessedForging of a Near-β Titanium AlloyL.J. Meng and T. Kitashima 882Additive Manufacturing of Multi Layered Bioactive Materials with Improved MechanicalProperties: Modelling AspectsM. Krzyzanowski, D. Svyetlichnyy and S. Bajda 888Nickel Supported Modified Zirconia Catalysts for CO2 Methanation in DBD PlasmaCatalytic Hybrid ProcessM. Mikhail, P. da Costa, S. Cavadias, M. Tatoulian, S. Ognier and M.E. Galvez 894Physical Modelling of Strain Induced Roughness of Copper Wire during Dieless DrawingProcessA. Milenin, D. Byrska-Wójcik and M. Wróbel 900Effect of Hot Processing on Mircrostructure and Properties of Flat Billets of TA15Titanium AlloyX.H. Min and C. Jin 906In Situ Observation during Copper Alloy Brazing Using an X-Ray SystemH. Miura, H. Okada, Y. Miyazawa and F. Kanasaki 911Activities of Non-Basal Slips in Rolled Mg-Li and Mg-Ce Alloys SheetsH. Miyano, K. Takemoto, H. Kitahara and S. Ando 917Creep Resistance of Ultrafine-Grained VT8M-1 AlloyI.M. Modina, A.V. Polyakov, G. Dyakonov, T.V. Yakovleva, A.G. Stotskiy, R. Valiev and I.P.Semenova 922The Domain of Portevin-Le Chatelier Effect in Al-3Mg AlloyA. Mogucheva, D. Yuzbekova and Y.I. Borisova 928The Effect of Hydrofluoric Acid Concentration in Sulfuric Acid-Based Desmutting Solutionfor Aluminium AlloysT. Monetta, A. Carangelo, F. Bravaccino, C. Sinagra and A. Acquesta 934

Materials Science Forum Vol. 1016 g

Influence of Hot Pressing Sintering Temperature on the Properties of Low-DensityAl0.5NbTa0.8Ti1.5V0.2Zr Refractory High-Entropy AlloyL. Moravcikova-Gouvea, Z. Kovacova, M. Kitzmantel, E. Neubauer, V. Jan and I. Dlouhy 940Strain Rate Dependent Mechanical Stability of Retained Austenite in Hot-Rolled Medium-Mn Sheet SteelsM. Morawiec and A. Grajcar 946Extra-Hardening of SPD-Processed Al-Mg Alloy with Minimum Grain SizesT. Morishige, Y. Suzuki and T. Takenaka 952Improving Mechanical Properties of Twin-Roll Cast AZ31 by Wire RollingM. Moses, M. Ullmann, R. Kawalla and U. Prahl 957Mechanical Behaviour of Beta Titanium AlloysN. Rao and G. Manivasagam 964Preliminary Development of Cold Spray Procedures for Nickel Aluminum Bronze CastingRepairC. Munro, P. Vo and B. Guerreiro 971High-Temperature Tribological Properties of ReB2-Based Ceramic/Si3N4 Sliding PairsT. Murakami and T. Ohana 978Effects of Retained Austenite Conditions on the Ductility of the Advanced High StrengthSteelsT. Murakami 984Solid State Amorphization and Alloy Parameters for High Entropy AlloysT. Nagase 990Corrosion Resistance Evaluation of a Stainless-Steel Brazed Joint in HCl SolutionH. Nagata, M. Ono, Y. Miyazawa, Y. Hayashi and Y. Bizen 997Stress Ratio Effect on Fatigue Crack Initiation Mechanism of Magnesium Alloy AZ31Y. Nakai, S. Kikuchi, K. Asayama and H. Yoshida 1003Applications of Smart Material of Li2O-(Nb/Ta)2O5-TiO2 Solid Solution Having a UniquePeriodical StructureH. Nakano 1009Crystal Orientation Relationships among Acicular Ferrite, Oxide and the Austenite Matrixin a Steel Weld MetalH. Nako, Y.J. Zhang, G. Miyamoto and T. Furuhara 1014FTMP-Based Kink Deformation and Strengthening Mechanisms for Mille-FeuilleStructuresY. Nawa and T. Hasebe 1019Influence of Radial Shear Rolling Regimes on the Homogeneity of Structural-Phase State,Mechanical Properties and Fatigue of near β Titanium AlloyE.V. Naydenkin, I.P. Mishin, I.V. Ratochka, O. Lykova and A.I. Manisheva 1024Progress towards a Complete Model of Metal Additive ManufacturingV.T. Nguyen, A.B. Murphy, G.W. Delaney, S.J. Cummins, P.W. Cleary, P.S. Cook, D.R.Gunasegaram, M.J. Styles and M.D. Sinnott 1031Investigation of Three-Dimensional Geometry of Butterfly Martensite and Analysis ofRelationship between Hardness of Lath/Butterfly Two-Phase Martensite and its GrainThickness in Medium-Carbon SteelT. Niho, K. Nagato and M. Nakao 1039Effect of Cold Reduction Rate on Ferrite Recrystallization Behavior during Annealing inLow-Carbon Steel with Different Initial MicrostructuresT. Ogawa, R. Hishikawa and Y. Adachi 1045Steel Production Technology Development for the Manufacture of Pipes Used in theExtraction and Transportation of Petroleum ProductsA. Ogoltcov and A.V. Mitrofanov 1051Mechanical Joining Utilizing Friction Stir FormingT. Ohashi, T. Nishihara and H.M. Tabatabaei 1058Threshold Voltage Control for MONOS Nonvolatile Memory with High-k HfN/HfO2Stacked Layers for Analog Memory ApplicationS.I. Ohmi and J. Pyo 1065Effect of Aging Heat Treatment at 400-600°C on the Microstructure and Tensile Propertiesof 15Cr-15Ni Ti-Stabilized Steel CladdingE. Curtet, P. Olier, A. Courcelle, B. Kedjar, M. Bono and L. Thilly 1071

h THERMEC 2021

In Situ Neutron Diffraction Measurement during Bainite Transformation andAccompanying Carbon Enrichment in Austenite at iMATERIA, J-PARC MLFY. Onuki, T. Hirano, K. Umemura, S. Sato and T. Tomida 1079Metallurgy of Highly Wear-Resistant Indefinite-Chill Work Roll Materials for Hot RollingMillsA. Paar, M. Aigner, C. Beal and C. Sommitsch 1085Anisotropy of Plastic Deformation in Hexagonal MetalsV. Paidar and J. Čapek 1091The Multiphase Micro- and Nanostructures of 0.2 and 0.4 C Direct-Quenched andPartitioned SteelsS. Pallaspuro, I. Miettunen, S.A. Aravindh, S. Ghosh, W. Cao, M. Somani and J.I. Kömi 1097When 3D Printing Meets Tribological Demands - Surface Functionalization Technologies asAdded Value of Existing and New Emerging ProductsI. Panaitescu, M.R. Ripoll, C. Katsich, R. Hubmann and E. Badisch 1103A Novel Method for Evaluation of Chromium Evaporation from Solid Oxide Fuel CellsInterconnects: A Feasibility StudyD. Paravidino, P. Piccardo and R. Spotorno 1109Microstructure Development in the Bonding Zone of Explosively Welded Ti and Cu SheetsH. Paul, P. Bobrowski, R. Chulist, M.M. Miszczyk and M. Prazmowski 1114Effect of Nano Sodium Titanate Whisker and Aramid Pulp on the Friction and WearBehavior of Resin-Based Brake MaterialZ.Z. Pei, R.B. Song, J. Xu, Y.F. Feng and K. Guo 1121Effect of Nb on the Austenite Microstructural Homogeneity of Hot Rolled RebarsB. Pereda, F. Bastos, B. López and J.M. Rodriguez-Ibabe 1127The Influence of the Sintering Temperature on the Properties of the 0.98Pb(Zr1-xTix)O3 -0.02La(Fe3+0.5, Nb5+0.5)O3 Ceramic SystemsA.I. Dumitru, G. Velciu, D. Patroi, J. Pintea, V. Marinescu and I. Peter 1134The Occurrence of a Peripheral Coarse Grain Zone (PCGZ) in Extruded Bars of AA 7108S.H. de Souza, R.L. Plaut, N.B. de Lima, R.R. de Oliveira and A.F. Padilha 1141Microstructure after Solution Annealing of the Nuclear Grade Austenitic Stainless SteelDIN 1.4970R.L. Plaut, A.F. Padilha, F.B. Neto and L.G. de Carvalho 1147Application of Image Analysis Method Combined with Microhardness Measurement toDetermine Phase FractionsA. Pohjonen, S. Koskenniska, J. Uusitalo, T.T. Nyo, J. Larkiola and J.I. Kömi 1153Stability of Ordered B2-βO and Disordered BCC-β Phases in Tial - A First Principles StudyF. Pyczak, V. Kononikhina and A. Stark 1159The Influence of Process Parameters on Structure of YSZ Coating Deposited by PlasmaSpraying on AISI 316L Stainless Steel Surface by APS Method and on Ti6Al4V TitaniumAlloy Surface by PS-PVD MethodM. Pytel, T. Kubaszek, P. Pędrak, M. Góral and M. Drajewicz 1166Microstructure of Al-2.5Fe Binary Alloy Fabricated by Laser Powder Bed FusionX. Qi, N. Takata, A. Suzuki, M. Kobashi and M. Kato 1175Effect of Extrusion Temperature and Thermal Treatment on Microstructure andMechanical Properties of Ti-1300 Alloy TubeY.L. Qi, L.Y. Zeng, W. Liu, H.M. Sun, Y. Du, S.W. Xin, W.L. Tan and S.Y. Zhang 1181Microstructure and Mechanical Properties of a Lamellar-Structured Low-Alloy TRIP SteelJ.Y. Meng, Z.G. Jia, T.L. Wang, K.F. Li and L.H. Qian 1188Near-Threshold Fatigue Crack Growth Behavior of ECAPed Ultrafine-Grained CopperS.D. Qu and Z.S. You 1193Microstructure Evolution during Strain-Induced Transformation of Austenite in anAustempered Ductile Iron (ADI)R. Raghavendran, A. Meena and M. Amirthalingam 1199Influence of Heat and Surface Treatments on the Fatigue Response of DMLS ManufacturedAlSi10mgD. Croccolo, M. de Agostinis, S. Fini, G. Olmi, L. Paiardini, F. Robusto and A. Bonomo 1205Microstructure Evolution during Multiaxial Processing of TA6VM.S. Jalme, C. Desrayaud, J. Favre, D. Fabrègue, S. Dancette, C. Schuman, J.S. Lecomte, E.Archaud and C. Dumont 1211

Materials Science Forum Vol. 1016 i

Mechanism of Void Formation during Brazing of Ni Paste Brazing Filler MetalM. Sakai, T. Sasaki and Y. Miyazawa 1218Internal Dislocation Density in Deformed GlidCop from X-Ray Line Profile AnalysisM. Sano, S. Takahashi, A. Shiro, T. Shobu and K. Nakada 1223Effect of Stacking Fault Energy and Solute Atoms on Microstructural Evolutions of FCCMetals Processed by Severe Plastic DeformationM. Asano, M. Yuasa and H. Miyamoto 1229Friction and Wear Response of a Hard-Anodized AA6082E. Santecchia, M. Cabibbo, A.M.S. Hamouda, F. Musharavati, A. Popelka and S. Spigarelli 1235Standardization of Cosα Method for X-Ray Stress MeasurementT. Sasaki, R. Mizuno, S. Takago and Y. Mishima 1240Effects of Alloying Elements on the Stability of ω-Fe Phase in Steel: A Density FunctionalTheory StudyS.A. Aravindh, S. Pallaspuro, W. Cao, M. Somani, M. Alatalo, M. Huttula and J.I. Kömi 1246Effects of Peening Direction on Reverse Transformation Induced by Shot-Peening for Fe-33%Ni AlloyH. Sato, T. Tominaga, T. Chiba, T. Moritani and Y. Watanabe 1252Non-Parametric Comparison of Crystallographic Orientation DistributionsH. Schaeben 1258Metal-Free and Carbon-Free Flexible Self-Supporting Thin Film ElectrodesC. Benbalit, E. Frau, O. Scheuber and S. Schintke 1264Fabrication of Silver-Nanowire/PVDF Self-Supporting Thin Flexible Electrode MembranesC. Benbalit, O. Scheuber, E. Frau and S. Schintke 1272Miniaturized Blood Sampling System with Integrated Sample PreparationS. Schlegel, E. Krumnow, A. Böhme, M. Minieri and A.H. Foitzik 1280From Biomaterial to Organoid - Bioprinting for PracticeV. Schlegel, A. Engels, V. Stoycheva, S. Bifaretti and A.H. Foitzik 1285Residual Stress in Automotive Powertrains: Methods and AnalysesD. Sediako, J. Stroh and S. Kianfar 1291Magnetization and XRD Studies of Laser Heat Treated SmCo5 PowdersN. Seetala, D. Henderson, J. Jno-Baptiste, H. Wen and S.M. Guo 1299High Energy Surface Implantation by Ion Nitrogen of Ultra- Fine Grained Ti-6Al-4V Alloyfor Engineering ApplicationI. Semenova, M. Smyslova, K. Selivanov, V. Sitdikov and R. Valiev 1305Industrial Fe-Simulation of Roughing Using an Automatic Solver Shifting TechniqueO. Seppälä, J. Ilmola and J. Larkiola 1312Spinning Formability of Al-Mg-Si AlloyS. Seta, J. Kobayashi and G. Itoh 1318Deformation Behavior of Single Particle Cold Spray Ti-6Al-4V SplatsM.M. Sharma, K.G. Judd, J.M. Schreiber and T.J. Eden 1325Effects of Microstructure on the Hydrogen Embrittlement Resistance of Ultra HighStrength Martensitic Steel SheetsK. Shibata, T. Hiramatsu, A. Shiraki, J. Kinugasa, T. Asai, Y. Utsumi and T. Murakami 1331Optimization of Preform for Stub Axle Forging Using Simulation SoftwareT.L. Dora, N.K. Singh and R. Ohdar 1337Hydrogen Embrittlement and Hydrogen Trapping Behaviour in Advanced High StrengthSteelsA. Smith 1344Properties of Alumina Coatings Deposited by Detonation SprayingV. Ulianitsky, A. Shtertser, I. Batraev and I. Smurov 1350Experimental Study and Modelling of the Ferritic Steel Anisotropic Behavior underAssociated and Non-Associated Flow RuleH. Soltani, O. Chahaoui and N. Matougui 1356Effect of Silicon Content on the Decomposition of Austenite in 0.4C Steel during Quenchingand Partitioning TreatmentI.H. Miettunen, S. Ghosh, M.C. Somani, S. Pallaspuro, D. Porter and J. Kömi 1361Microstructure and Shape Memory Behavior of Ti-18Nb-6Zr (at.%) AlloyX.Y. Song, W.J. Ye and S.X. Hui 1368

j THERMEC 2021

Titanium Alloy Milling Using Abrasive Water Jet for Repair Application: Modifications inSurface Quality and Material Integrity Following Plain Water Jet CleaningX. Sourd, M. Salem, R. Zitoune, A. Hejjaji and D. Lamouche 1374High-Temperature Oxidation of AISI441 Ferritic Stainless Steel for Solid Oxide Fuel CellsR. Spotorno 1381Effect of Interstitial Elements on the Cryogenic Mechanical Behavior of FCC High EntropyAlloysA. Semenyuk, M. Klimova, S. Zherebtsov and N. Stepanov 1386Microstructure Refinement Effect on EUROFER 97 Steel for Nuclear Fusion ApplicationG. Stornelli, R. Montanari, C. Testani, L. Pilloni, G. Napoli, O. di Pietro and A. di Schino 1392The Effect of Long-Term Heating on Thermal Stability of Ultra-Fine Grained TitaniumAlloy VT8M-1 Processed by Rotary SwagingA. Stotskiy, T.V. Yakovleva, G. Dyakonov, A.V. Polyakov and I. Semenova 1398Structure and Microstructure of Advanced Materials Characterized by Neutron DiffractionP. Strunz, R. Kocich, P. Beran, L. Kunčická, D. Mukherji, R. Gilles and M. Hofmann 1404Evaluation of Interfacial Thermal Resistance of Al-AlN Composites by Using Image-BasedCalculationK. Sugio, T. Kawata, Y. Choi and G. Sasaki 1411The Effect of Ni Precursor Salts on Diatomite Supported Ni-Mg Catalysts in Methanation ofCO2C. Sun, J. Krstic, V. Radonjic, M. Stankovic and P. da Costa 1417Performance of a Matrix Type High Speed Steel after Deep Cryogenic and Low TemperingTemperatureK. Worasaen, A. Stark, K. Tuchinda and P. Suwanpinij 1423Development of High-Accuracy Simulation Test Technology for Hot StampingA. Suzuki, Y. Fujii, T. Kimura, M. Kawano and T. Inazumi 1430Effect of Temperature and Humidity on Degradation Behavior of Cu/Epoxy Interfaceunder High Temperature and High Humidity AgingR. Suzuki, I. Shohji, T. Kobayashi and Y. Tonozuka 1436Tensile Deformation of Si Single Crystals at High TemperaturesT. Suzuki, M. Tanaka, T. Morikawa, Y. Okuyama, J. Fujise and T. Ono 1443In Situ Evaluation of the Joining Defects in a Pb-Free Soldered JointH. Tajima, Y. Nakamura, Y. Miyazawa and H. Tameda 1448Evaluation of Tensile Shear Strength for Lap Joint of Dissimilar SteelsY. Takashima, T. Washio and F. Minami 1454Microstructure Modification of 3D Printed Aluminium Alloys by Friction Stir ProcessingZ.L. Du, M.J. Tan and J.F. Guo 1460Investigation of Bonding Strength of Al Solid Phase Diffusion Bonded Joint with SurfaceTreatment Using Electrolyzed WaterT. Tanaka, I. Shohji, T. Kobayashi and H. Imai 1466Powders for Additive Manufacturing: From Design to CertificationO. Tassa, L. Alleva and R. Sorci 1473Mechanical Property and Heat Treatment Behaviour of Ti-Zr-Fe AlloysT.H. Chang, M. Adachi, M. Ueda and M. Ikeda 1479Study of High Temperature Properties of AlSi10Mg Alloy Produced by Laser-BasedPowder Bed FusionM. Tocci, A. Varone, R. Montanari and A. Pola 1485Optimization of Molecular Characteristics via Machine Learning Based on ContinuousRepresentation of MoleculesK. Sato and K. Tsuruta 1492Utilisation of Titanium and Titanium Dioxide as Scaffolds for Proliferating Coral ReefM. Ueda, C. Sawatari, T. Takahashi, H. Tsuruta, H. Tokushige, H. Hikosaka, D. Yonetsu and M.Ikeda 1497Improvement of Strength and Ductility by Combining Static Recrystallization and UniqueHeat Treatment in Co-20Cr-15W-10Ni Alloy for Stent ApplicationK. Ueki, S. Yanagihara, K. Ueda, M. Nakai, T. Nakano and T. Narushima 1503Effects of Carbon Content Change on Growth of Compound Layer in Surface of NitridedSteelT. Umehara and M. Yuya 1510

Materials Science Forum Vol. 1016 k

Bending and Welding of New High Oxidation Material - Thor™ 115M. Urzynicok and K. Kwiecinski 1515Surface Morphology of Refractory Metals Submitted to a Single Laser PulseP. Gaudio, R. Montanari, E. Pakhomova, M. Richetta and A. Varone 1526Integral Computer Model for Simulating Microstructure Evolution duringThermomechanical Processing and Heat Treatment of Steels and Predicting their FinalMechanical PropertiesA.A. Vasilyev, D. Sokolov, S. Sokolov and N.G. Kolbasnikov 1532Studies on Thermomechanical Cycling Characteristics of an Ni-Ti-Cu Shape Memory AlloyG. Swaminathan and V. Sampath 1538Finite Element Analysis of Surface Modification of Titanium Alloy Used for Hip ImplantA. Vulović, F.G. Warchomicka and N. Filipović 1544Forming an Optically Transparent Graphene Film via the Transformation of C60 MoleculesY. Wada, K. Miyamoto, T. Yamada and T. Kuzumaki 1549Effect of the Pre-Strain on the Elastic Behavior of a Dual-Phase Steel with DifferentMartensite ContentsM. Wallner, R. Schneider, K. Steineder, D. Krizan, T. Hebesberger and P. Larour 1555Adhesion Properties of Thin Film Multilayers: Comparison of Nanoindentation and Four-Point-Bending TechniquesT. Walter, M. Zareghomsheh, G. Khatibi and H. Danninger 1561Effect of Strain Rate on Compressive Behavior of a ZrCuNiAl Bulk Metallic Glass at RoomTemperatureZ.P. Guo, C.T. Wang, Y. He, Y. He, L. Guo, X.B. Hu and S. Lan 1569Effect of Cellular Dislocation Structure on the Strength of Additively Manufactured 316LStainless SteelM.S. Wang, M. Fan, S. Cruchley and Y.L. Chiu 1576Syngas Production by Dry Methane Reforming over Mg Doped NiO-ZrO2 CatalystsY. Wang, Y.N. Wang, P. da Costa and C.W. Hu 1585Deformation Property of Dense Oxide Coated Magnesium Alloy SurfaceA. Watazu and T. Sonoda 1591Remelting of Thermal Spraying Coatings - Technologies, Properties and ApplicationsM.S. Weglowski, J. Dworak, K. Kwiecinski, J. Pikuła, K. Krasnowski, R. Jachym, S. Dymek, I.Kalemba-Rec, A. Wrona and K. Kustra 1597Processing of Nanostructured Bulk Fe-Cr Alloys by Severe Plastic DeformationL. Weissitsch, M. Stückler, S. Wurster, R. Pippan and A. Bachmaier 1603Study of the Microstructure and Mechanical Properties Obtained by Laser Boost in SLMProcess for the Ti-64 AlloyC. Widomski, D. Solas, F. Brisset, A.L. Helbert, T. Baudin and S. Lebel 1611The Influence of HPT on Microstructure and Wear Resistance of Al-7wt%Si-2wt%Fe AlloyJ. Wongsa-Ngam, J. Xu, C. Phongphisutthinan and T.G. Langdon 1618Mechanical Behaviour of Rubber Material with Consideration to Mullins EffectC.S. Woo and H.S. Park 1624Investigation on Surface Roughness in Electron Beam Selective Melting by MesoscaleModelC.C. Wu, M.Q. Zafar and H.Y. Zhao 1630Static Recrystallization in Aluminum/Graphene CompositesX.D. Wu, X.L. Liu, L.F. Cao and G.J. Huang 1636Correlation of Segregation Energies of Ni and Fe with Mendeleev NumberW. Wunderlich 1642Operando Monitoring of Charging Processes in Battery Cathodes by Magnetometry andPositron AnnihilationG. Klinser, H. Krenn and R. Würschum 1647Goss Texture Evolution in a Grain-Oriented Fe-6.5wt%Si Steel Processed by Strip-CastingX. Liu, H.J. Xu, Z.Y. Gao, Y.B. Xu, J. Yu, H.T. Jiao, Y.H. Li and J.P. Li 1653Investigation of the Role of Intermetallic Phases in Microstructure of UFG TitaniumVT8M-1 AlloyT.V. Yakovleva, G. Dyakonov, A. Stotskiy, I.M. Modina and I. Semenova 1659The Effect of Aging Conditions on the Stress Relaxation Behavior of 17-7PH Stainless SteelS. Yamasaki and K. Takano 1664

l THERMEC 2021

First-Principles Study of Epoxy Resin Adhesion to Tin Oxide SurfaceJ. Yamashita and N. Nunomura 1670Formation of Cemented Tungsten Carbide Layer with Compositional Gradient Processedby Directed Energy DepositionY. Yamashita, Y. Funada, T. Kunimine, Y. Sato and M. Tsukamoto 1676The Impact of Interface Characteristics on Mechanical Performance of a Hot-ForgedCu/Ti-Coated-Diamond CompositeL. Lei, L. Bolzoni and F. Yang 1682Effect of Chemical Composition on Grain Refinement of AlxCoCrFeNi High Entropy Alloyswith NiAl Grain Boundary PrecipitatesH.Y. Yasuda, H. Miyamoto, T. Inagaki, K. Cho and T. Nagase 1690Improvement of Mechanical Properties of Laminated Composites by Using Cryogenic RollBondingH.L. Yu, J. Liu and L. Wang 1696Development of Cu Coating on Ceramic Substrates by Low Pressure Cold Spray and itsDeposition Mechanism AnalysisM. Yu, Y. Ichikawa and K. Ogawa 1703Thermal Degradation Behavior of Hydrogen Permeability of Pd-Coated V-Alloy Membranefor Hydrogen Separation and PurificationH. Yukawa, T. Nambu and Y. Matsumoto 1710Analysis of Different Thermal Conductivity Measurements for Al-Si Casting AlloysY.L. Zhou, G. Zhong, Z.K. Wang, S.P. Lin and J.C. Zhang 1715Dislocations of Ti-600 Alloy Crept at 600°C with Two StressesL.Y. Zeng, X.N. Mao, Q. Hong, Y.L. Qi and Y.Q. Zhao 1722Microstructure and Mechanical Properties of Cu-Fe Alloys via Powder MetallurgyC.Z. Zhang, C.G. Chen, T.X. Lu, P. Li, F. Yang, W.W. Wang and Z.M. Guo 1727Numerical Simulation of Microstructure Evolution during Continuous Hot Rolling Processof GCr15 Steel RodL.W. Zhang, F. Li, C. Zhang, P.G. Mao and C.Q. Li 1733Effect of Tempering Time on Microstructure and Mechanical Properties of SA738 Gr.BSteelY.M. Li, S.Z. Zhang, Z.W. Jiang, S. Yu, Q.B. Ye, M.Q. Yang and Y.H. Xi 1739The Microstructure and Properties of Low Carbon PM 625 Alloy for Marine-BasedApplicationL. Zheng, G.Q. Zhang, X.Q. Xu and Z. Li 1747Efficiency of Microstructure Refinement in Ti-Based AlloysS. Zherebtsov, N. Stepanov and G. Salishchev 1753Metallic Composites, Prepared by Deformation ProcessingG.F. Korznikova, A.P. Zhilyaev, A.A. Sarkeeva, R.Y. Lutfullin, R.U. Shayahmetov, G.R.Khalikova, R.K. Khisamov, K.S. Nazarov and R. Mulyukov 1759The Effect of Deformation Strain on Texture Uniformity in Tantalum Sheet duringAsymmetric Cross RollingJ.L. Zhu, S.F. Liu, D.D. Long, Y.H. Liu, S.Y. Zhou and J. Zhang 1765Effects of Powder Microscopic Defects on Densification and Mechanical Properties of WCvia Spark Plasma SinteringL. Zhu, J.F. Wang, Z.B. Tu, N. Xue and W.W. Li 1770Three-Dimensional Characterization of Morphology and Crystallography of a GoldNanoisland FilmW.G. Zhu, G.L. Wu, T.L. Huang, S. Schmidt, L. Zhang, Z.Q. Feng, J.N. Deng and X.X. Huang 1778Unmixed Joint of A1050 and C1020 by Friction Stir Butt WeldingT. Nagaoka, T. Kyouda, S. Tongge and H. Zhang 1784Spark Plasma Sintering of Paper-Derived Ti3AlC2-Based Composites: Influence ofSintering TemperatureM. Syrtanov, E. Kashkarov, T. Murashkina and N. Travitzky 1790Fabrication of Be-Ta Ti Alloys without Pre-Alloyed Powders via SLMM. Todai, T. Nagase and T. Nakano 1797Martensitic Transformation of High-Entropy and Medium-Entropy Shape Memory AlloysH. Matsuda, M. Shimojo, H. Murakami and Y. Yamabe-Mitarai 1802

Materials Science Forum Vol. 1016 m

Suppression of Intergranular Fracture in 7000 Series Aluminum AlloysG. Itoh, K. Hiyama, B.F. Lyu and J. Kobayashi 1811Elasto-Plastic Deformation of Heterogeneous Metallic Materials: An ExperimentalApproach with AlMg4Si10M. Schöbel, D. Tolnai and M. Hofmann 1816Effects of Tensile Testing Temperature on Mechanical Properties and DeformationBehavior in Medium Mn SteelsY. Kawasaki, Y. Toji, Y. Takeshi and Y. Funakawa 1823Characteristics of Cube Orientation for Pure Iron Tape Fabricated by Cold Rolling andAnnealingD. Okai, A. Yamamoto, T. Doi and H. Adachi 1830The Application of Neutron Diffraction Techniques (NDT) in Measuring Residual Strain-Stresses of Engineering MaterialsY.L. Ma, S.Y. Zhang, P. Zhang, S. Paddea, Z.F. Gong, J.B. Gao, X. Zhan, C. Wang, M.Q. Chu, F.Bian and Y. Wang 1835Evaluation of Color Tone and Exfoliation Resistance of Porcelain-Firing Ti with WhiteOxide Coating as an Opaque LayerT. Kuratani, E. Miura-Fujiwara and T. Yamasaki 1841Effects of Nb Content and Heat Treatment on Fretting Wear Behavior of Ti-Nb AlloysN. Nishimura, E. Miura-Fujiwara and T. Yamasaki 1846Modelling Dilatometry Data of Isothermal ω-Phase Formation in a Strongly β-StabilisedTiV-AlloyR.J. Enzinger, M. Luckabauer, T. Ichitsubo and R. Würschum 1851Hardness Prediction of AA 2024-T3 FSW WeldS. Galisson, D. Carron, P. Le Masson, G. Stamoulis, E. Feulvarch and G. Surdon 1857Density Functional Theory Study of the Adsorption of Metal Adatoms on GrapheneN. Nunomura, J. Yamashita and S. Sunada 1863Investigation of CGHAZ Simulations of Low-Carbon Bainitic SteelsT.T. Nyo, A. Kaijalainen, J. Hannula and J.I. Kömi 1869Grey-Fuzzy Logic Based Approach in Multi-Response Optimization of Semi-Solid Forgingof A356 Aluminium AlloyR. Ohdar, N.K. Singh, A. Kumari and R. Kumar 1875Microstructure Factor of Creep Behavior in Near-α Ti AlloyH. Masuyama, T. Matsunaga, Y. Toda, T. Ito, M. Shimojo and Y. Yamabe-Mitarai 1882

Table of Contents