Table of Contents - Arnetarnetonline.arnet.com.ar/CMEDocuments/ATA/pdf/Huawei_Manual.pdf · About This Manual This manual provides a comprehensive user’s guide and installation

User Manual SmartAX MT810 ADSL CPE Table of Contents

i

Table of Contents

Chapter 1 Overview .......................................................................1-1 1.1 About ADSL .......................................................................1-1 1.2 Features .............................................................................1-1 1.3 Protocols ............................................................................1-2 1.4 Cautions .............................................................................1-2 1.5 Abbreviations .....................................................................1-2

Chapter 2 Hardware Installation...................................................2-1 2.1 Packing List........................................................................2-1 2.2 Outlook...............................................................................2-1

2.2.1 Indicator Status Introduction....................................2-2 2.2.2 Connector Introduction ............................................2-2

2.3 System Requirements........................................................2-2 2.4 Hardware Installation .........................................................2-3

2.4.1 External Splitter .......................................................2-3 2.4.2 Physical Level Link ..................................................2-4

Chapter 3 Software Installation....................................................3-1

Chapter 4 Installation Confirm .....................................................4-1 4.1 Installation for Windows 2000 System...............................4-1 4.2 Additional Details for Windows 98 .....................................4-5

Chapter 5 Customizing Communication Setting........................5-1 5.1 Software Set up..................................................................5-1 5.2 Status Monitor ....................................................................5-3

User Manual SmartAX MT810 ADSL CPE Table of Contents

ii

Chapter 6 Internet Access ............................................................6-1 6.1 Preparation.........................................................................6-1 6.2 PPPoE Mode......................................................................6-1 6.3 Static IP Address Mode ...................................................6-10 6.4 Dynamical IP Address Assigning Mode...........................6-13

Chapter 7 Questions & Answers..................................................7-1

Chapter 8 Software Uninstall........................................................8-1

About This Manual

This manual provides a comprehensive user’s guide and installation manual for SmartAX MT810 ADSL CPE. It has been organized in such a way to make it easy to follow by users worldwide. In order to ensure optimal comprehension, the following list provides brief descriptions of the formatting styles used throughout this manual.

Commands: Commands are always referred to by using the word “click” before them. These commands are always shown as bold-faced words. For example, click Next, click OK, or click Cancel.

Names of Windows (Dialog Boxes): The names of the windows (also referred to as dialog boxes) that appear on the PC screen are always referred to in quotes. For example, the “Setup Complete” window.

Names of Options in Windows: The names of options to choose from inside the windows that appear on the PC screen are always referred to in italics. For example, choose the Yes, I want to restart my computer now option from the window.

Notes: In some cases, preparatory or cautionary information is needed before proceeding onto the next step in an installation process. This kind of information is provided in the form of notes, which are always referred to in bold-faced and italicized letters. For example, Note: To access the Control Panel, the driver must be running. Also, make sure the USB cable is plugged into the modem.

User Manual SmartAX MT810 ADSL CPE Chapter 1 Overview

1-1

Chapter 1 Overview

1.1 About ADSL Asymmetric Digital Subscriber Line (ADSL) technology provides

high-speed data access across common phone lines (copper wires) by making use of previously unused frequency bandwidth above the voice band. ADSL signal uses different frequency from the voice signal. ADSL service is able to coexist with your telephone service on the same line. ADSL is asymmetric in the sense that it provides higher data rate in the downstream (receive) direction than in the upstream (transmit) direction. Asymmetric operation is ideal for home and small office use where files and information are downloaded more frequently than uploaded.

1.2 Features USB interface, Plug-and-Play Bus-powered, external power supply is not required Compatible with T1.413, G.dmt, G.lite and multimode Adjusts speed automatically Supports UBR/VBR/CBR ATM Provides DSL downstream data rates up to 8 Mbps, and

upstream rates up to 1024 Kbps Supports Windows 2000, Windows ME, Windows XP and

above Windows 98 Windows GUI management Power consumption: less than 2W Operating Environment: 0 OC~+50 OC Weight: 100g


1-2

1.3 Protocols Complies with T1.413, G.dmt (G.992.1), G.lite (G.992.2) Complies with RFC1483 Complies with USB1.1

1.4 Cautions 1) Do not connect the ADSL to the telephone line directly; it is

recommended to connect it to the splitter’s “MODEM” port. 2) Make sure the adapter does not have capacitances, diodes,

etc. 3) MT810 is only for indoor use. 4) Always keep MT810 dry. 5) Keep away from high power consuming machine; avoid

electromagnetic interference and heat. 6) This product has been designed to comply with the

requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

1.5 Abbreviations The following abbreviations can be referred in this manual:

Table 1-1 Abbreviation

ADSL Asymmetry Digital Subscriber Line

ATM Asynchronous Transfer Mode

CBR Constant Bit Rate

CPE Customer Premises Equipment


1-3

DNS Domain Name Server

FTP File Transfer Protocol

GUI Graphical User Interface

IE Internet Explorer

IP Internet Protocol

ISP Internet Service Provider

PPP Point-to-Point Protocol

PPPoE PPP-over-Ethernet

PVC Permanent Virtual Circuit

TCP/IP Transmission Control Protocol / Internet Protocol

UBR Unspecified Bit Rate

USB Universal Serial Bus

VCI Virtual Circuit Identifier

VPI Virtual Path Identifier

WAN Wide Area Network

User Manual SmartAX MT810 ADSL CPE Chapter 2 Hardware Installation

2-1

Chapter 2 Hardware Installation

2.1 Packing List 1) SmartAX MT810 ADSL CPE : 1 PCS 2) Telephone Cable : 2 PCS 3) Splitter : 1 PCS 4) USB Cable : 1 PCS 5) User Manual : 1 PCS 6) Installation CD : 1 PCS

2.2 Outlook

Figure 2-1 USB ADSL modem


2-2

2.2.1 Indicator Status Introduction

POWER Red LED On Power on

Flash Trying to make connection LINK Red LED

On Connect successfully

DATA Red LED Flash There is data traffic over the line

2.2.2 Connector Introduction

1) LINE port: RJ-11 port connects MT810 to a splitter. 2) USB port: Connects MT810 to user computer through

USB cable.

2.3 System Requirements Recommended system requirements for the MT810 are:

1) Processor: Intel-compatible Pentium II 300 or above 2) Memory: 128 MB or above

Caution:

Recommend to use Windows 2000, Windows ME, Windows XP and above Windows 98 SE.


2-3

2.4 Hardware Installation

SmartAX MT810

Figure 2-2 Hardware connection illustration

2.4.1 External Splitter

Telephone and modem may interfere with each other. To avoid that, an external splitter is required.

Figure 2-3 External splitter connection


2-4

The external splitter has three ports: LINE, MODEM, and PHONE. While using it, ensure to make right connections.

2.4.2 Physical Level Link

Perform the following steps to install the MT810

1) Connect the splitter to wall jack using one telephone cable.

2) Use the other telephone cable to connect “MODEM” port of the splitter and “LINE” port of MT810.

3) Use USB cable to connect “USB” port of MT810 and “USB” port of your computer.

Caution:

Before plugging USB cable into USB port, you must install driver program first. If MT810 has been connected to the computer through USB port, the computer will prompt that new hardware has been found. Then cancel the installation. The detailed installation steps can be referred to “Chapter 3 Software Installation”.

User Manual SmartAX MT810 ADSL CPE Chapter 3 Software Installation

3-1

Chapter 3 Software Installation

This chapter will give introduction to the ADSL modem driver software installation for Windows 2000. For other operation system, such as Windows 98, Windows XP, Windows ME, please follow the same procedures. You are recommended to use SETUP.EXE file to install driver program.

1) Insert the attached installation disk into your CD-ROM and locate “SETUP.EXE” from F:\USB ADSL A\Driver directory (F: is your CD-ROM directory). Double click SETUP.EXE.

2) After the following window pops up, click Next.


3-2

3) Installation is thus started.

4) After installation, the following window will pop up, select Yes, I want to restart my computer now, and click Finish.


3-3

5) After your PC restarted, a message “Found New

Hardware” will pop up. Please wait for the installation process to be conducted automatically.

6) When the following dialog box appears, click OK to finish the installation.

User Manual SmartAX MT810 ADSL CPE Chapter 4 Installation Confirm

4-1

Chapter 4 Installation Confirm

4.1 Installation for Windows 2000 System 1) Click Start- Settings- Control Panel. 2) Double click “System” icon, select “Hardware” panel.

3) Click Device Manager to open “Device Manager” window.


4-2

4) Click Network adapters-USB ADSL LAN Adapter. See

above. 5) Double click USB ADSL LAN Adapter, “USB ADSL LAN

Adapter Properties” window pops up.


4-3

6) If Device status displays: “The device is working properly”, close “USB ADSL LAN Adapter Properties” window, and then return to “Control Panel”

7) Double click Network and Dial–up Connections icon (For Windows XP, double click Network Connections icon), then double click Local Area Connections.


4-4

8) If USB ADSL LAN Adapter icon appears in “General” window, it indicates that the USB driver has been installed. Click OK to close the window.


4-5

4.2 Additional Details for Windows 98 For checking procedures after the installation in Windows 98,

the following parts are somewhat different.

1) Select “Network” icon from “Control Panel” window, and double click it.


4-6

2) If “USB ADSL LAN Adapter” icon appears in “Configuration” window, it indicates that the USB driver has been installed, click OK to close the window.


4-7

User Manual SmartAX MT810 ADSL CPE

Chapter 5 Customizing Communication Setting

5-1

Chapter 5 Customizing

Communication Setting

Before setting, please contact your DSL service provider for information such as VPI/VCI, etc. Record the default settings information if the change is unnecessary.

5.1 Software Set up 1) Make sure the device driver has already been installed

correctly, after which the icon of ADSL (“ ”) will appear

on the right of the system tray, as the following:

2) Double click the icon of ADSL, a message window appears as the following:



5-2

Table 5-1 Parameter description

Information Description

Transmit Upstream data rate from ADSL link. (Kbps) Line Rate

Receive Downstream data rate from ADSL link (Kbps)

Transmit Real time transmitting data rate (Kbps)

Data Rate Receive Real time receiving data rate (Kbps)

3) Use Alt-D key to pop up the “Administrative” window, and

choose “CONFIG” panel.



5-3

We suggest keeping the default settings. You need only to

change values of the VPI/VCI or encapsulation type as your DSL service provider offered, and click Apply. The “LINK” LED will flash a while and then keep on. Then you can access the Internet.

5.2 Status Monitor The icon of ADSL on your desktop indicates the ADSL working

state. There are six different colors and their meanings are described as follows:



5-4

Table 5-2 Status Monitor

Icon Description Status Description

(Red icon) Not working

(Yellow icon) Communication with loop

(Dark green icon) Link established but no data transferring

(Light green icon) Transmitting or receiving data

(Up half light green, down half dark green icon)

Data transmitting in process

(Bottom half light green, up half dark green icon)

Data receiving in process

User Manual SmartAX MT810 ADSL CPE Chapter 6 Internet Access

6-1

Chapter 6 Internet Access

6.1 Preparation The following information may be required for Internet access

in different accessing modes. Contact your DSL service provider before further proceedings.

For PPPoE dial-up mode (common access mode)

PPPoE dial-up application

User Account and Password

Static IP allocation mode

IP Address

Subnet Mask

Gateway Address

DNS Address

WINS Address

Dynamically obtaining IP address

No information shall be acquired from your DSL service provider.

6.2 PPPoE Mode PPPoE is a specification for connecting multiple computer

users on an Ethernet to a remote site through common customer premises equipment (CPE). PPPoE combines the Point-to-Point


6-2

Protocol commonly used in dialup connections with the Ethernet protocol, which supports multiple users in a Local Area Network.

Caution

Please confirm that the LED “LINK” of ADSL Modem is light on, which indicate the physical connections loop already established

A third part software is needed while using PPPoE dialup mode to build an Internet access. For Microsoft Windows 98, Windows 98 SE, Windows ME and Windows 2000 operating systems, a third party software such as “Enternet 300” or “WINPOET ”is needed in PPPoE dialup mode. For Windows XP, the following procedure will be used to build a dial-up connection.

1) Click Start->All Programs->Accessories->Communications->Network connections

2) Click Create a new connection, a new window will pop up, click Next.


6-3

3) Choose Connect to the Internet, and click Next.


6-4

4) In “New connection Wizard” window choose Set up my connection manually, and click Next.


6-5

5) Choose Connect using a broadband connection that require a user name and password option, and click Next.


6-6

6) Enter the DSL SERVICE PROVIDER’S name you want, and click Next.


6-7

7) Enter your user name and password then click Next.


6-8

8) The following window appears, which indicates that you have completed establishing the connection, choose Add a shortcut to this connection to my desktop, and click Finish. A shortcut of dial-up connection appears on the desktop.


6-9

9) Double click the icon of dial-up connection, a massage

window pops up. Click Connect.


6-10

10) When the window of the dial-up connection disappears, in system tray, a small icon as follows will indicate the connection is built successfully.

6.3 Static IP Address Mode Use Windows 2000 as an example, the setting procedures in

other operating systems are similar with the following description. In static IP address mode, if your DSL service provider has specified the IP and DNS address information, the following procedures can be used to configure TCP/IP properties.


6-11

1) Click Start->Settings->Network and Dial-up connections, choose the icon of “Local Area Connection” whose associated equipment is “USB ADSL LAN Adapter”.

2) Double click Local Area Connections to open “Local Area connections Properties” window. Then double click Internet Protocol (TCP/IP)


6-12

3) “Internet Protocol TCP/IP Properties” window will pop up,

select Use the following IP address and enter the IP address Subnet mask and default gateway in the space provided, select Use the following DNS service address and enter the DNS service address.


6-13

4) Click OK to close “Internet protocol (TCP/IP) properties” windows, all settings will be saved.

6.4 Dynamical IP Address Assigning Mode The setting procedures are similar with those of “Static IP

Address mode”. Open “Internet Protocol (TCP/IP) Properties” window, select Obtain an IP address automatically and Obtain DNS service automatically, click OK to close “Internet protocol (TCP/IP) Properties” window, all settings will be saved.


6-14

User Manual SmartAX MT810 ADSL CPE Chapter 7 Questions & Answers

7-1

Chapter 7 Questions & Answers

Question 1: When connecting to WAN (Wide Area Network), the message appears that PVC connections failed, why?

Answer:

1) Check the connections between ADSL modem and telephone line.

2) If you ensure the connection has no problem, proceed to check the VPI and VCI Parameters. Change these settings if they are inconsistent with the information your DSL service provider provides.

Question2: Compare with using ADSL modem independently, why I have slower speed while using modem and phone at same time?

Answer: To separate the data signal and voice analog signal, a splitter is necessary. It has three ports: PHONE, LINE, MODEM; make sure the connection is correct.

Question 3: Why sometimes the access speed is not faster than dial-up modem?

Answer: There are several reasons:

1) If you visit an oversea website, your speed will be limited by the export bandwidth and the configurations on the server side.

User Manual SmartAX MT810 ADSL CPE Chapter 7 Questions & Answers

7-2

2) ADSL modem is multimode, that is, it automatically determines the type of modem at the central office and configures itself accordingly. Once the correct mode is determined, the modem automatically determines the optimal data rate for the line. It depends on the type of modem at the central office and the loop condition.

Question 4: Why browsing web page is slow after ADSL CPE and Enternet300 have been installed?

Answer: This is because Internet connection wizard points to a wrong connection. Enternet300 uses Local Area Network virtual dial-up, but the IE default is using normal dial-up when browsing a web site. IE will seek the dial-up interface first, and then seek proxy in Local Area Network, lastly point to Enternet300 interface, which would make it slow. You need to run the Internet connect wizard to point to LAN mode and disable the proxy so as to solve the problem.

User Manual SmartAX MT810 ADSL CPE Chapter 8 Software Uninstall

8-1

Chapter 8 Software Uninstall

Remove the USB ADSL Modem software drivers by performing the following steps:

1) Chose Start–>Programs–>Huawei SmartAX MT810–> Uninstall.

2) Click OK to confirm files deletion.

User Manual SmartAX MT810 ADSL CPE Chapter 8 Software Uninstall

8-2

3) Wait until the “Huawei SmartAX MT810 Setup” window pops up. Select the Yes, I want to restart my computer now, and click Finish.

4) A notification message pops up, remove the MT810, Click

OK, and restart your computer now.