Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
T80 Series Model T8045 Maximum Flow Rate: 45 gpm (170.4 l/min)
Maximum Pressure: 3000 psi (207 bar)
T8045 with Nickel Aluminum Bronze pump head
• Seal-lessdesigneliminatesleaks,hazardsandtheexpenseassociatedwithsealsandpacking
•LowNPSHrequirementsallowforoperationwithavacuumconditiononthesuction-positivesuction pressure is not necessary
•Canoperatewithaclosedorblockedsuctionlineandrundryindefinitelywithoutdamage,eliminatingdowntimeandrepaircosts
•Uniquediaphragmdesignhandlesmoreabrasiveswithlesswearthangear,screworplungerpumps
•Hydraulicallybalanceddiaphragmstohandlehighpressureswithlowstress
•Lowerenergycoststhancentrifugalpumps•Ruggedconstructionforlonglifewithminimal
maintenance•Compactdesignanddouble-endedshaftprovideavarietyofinstallationoptions
T Series pumps feature the Hydra-Cell seal-less design, eliminating clean-up costs from leaking seals or packing and protecting operators from dangerous fluids such as those containing hydrogen sulfide.
2 • www.Hydra-Cell.com
T80 Series Model T8045 Performance
Capacities
Maximum Flow at Designated Pressure
Due to Wanner Engineering continuous improvement practices, performance data and specifications may change without notice.
Revolutions Per Minute200 225 325 375 425 450
50.0
20.0
47.0
44.0
41.0
38.0
35.0
32.0
29.0
26.0
23.0
Lite
rs P
er M
inut
e
Gal
lons
Per
Min
ute
124.0
130.0
136.0
142.0
148.0
154.0
118.0
166.0
172.0
178.0
184.0
189.0
160.0
82.0
88.0
94.0
100.0
106.0
112.0
75.7275 400350300250
500 psi (34 bar)1500 psi (103 bar)3000 psi (207 bar)
T8045
Flow Max. Max. Flow Input @ 3000 psi (207 bar) Model rpm gpm l/min
T8045 450 45.0 170.4
Consult factory when operating below 20 gpm (75.7 l/min).
PressureMaximum Inlet Pressure 500 psi (34 bar) Maximum Discharge Pressure 3000 psi (207 bar)
www.Hydra-Cell.com • 3
T80 Series Model T8045 Specifications
Revolutions Per Minute
12
NPSH
r (fe
et o
f wat
er)
NPSH
r (m
eter
s of w
ater
)
13
14
15
16
17
18
3.75
4
4.25
4.5
4.75
5
5.25
W0505
5.5
200 350 450300 400 500250
Net Positive Suction Head (NPSHr)
Attention!
Whensizingmotorswithvariablespeeddrives(VFD):ItisveryimportanttoselectamotorandaVFDratedforconstanttorqueinverterdutyserviceandthatthemotorisratedtomeetthetorquerequirementsofthepumpthroughoutdesiredspeedrange.
Calculating Required Horsepower (kW)*
gpm x psi
=electricmotorhp*
1,460
lpm x bar
=electricmotorkW*
511
* hp (kW) is required application power.
W0499B
Outlet Oil Fill Cap
Oil Fill Capwith Dipstick
Power End
ID Plate
Crankshaft
Oil Drain Plugs
Hydraulic SectionInlet
Fluid End
Flange Shown
Flow Capacities @3000 psi (207 bar) Model rpm gpm l/min T8045 450 45.0 170.4Delivery Pressure psi (bar) gal/rev liters/rev 500 (34) 0.107 0.406 1500 (103) 0.105 0.397 3000 (207) 0.101 0.384rpm Maximum: 450 Minimum: 200 Consult factory for speeds less than 200 rpm Maximum Discharge Pressure Metallic Heads: 3000 psi (207 bar) Maximum Inlet Pressure 500 psi (34 bar) Operating Temperature Maximum: 180˚F (82.2˚C) Minimum: 40˚F (4.4˚C) Consult factory for temperatures outside this rangeMaximum Solids Size 800 microns Input Shaft Left or Right SideInlet Ports 3-1/2 inch Class 300 RF ANSI Flange or 2-1/2 inch NPTDischarge Ports 1-1/2 inch Class 2500 RJ ANSI Flange or 1-1/2 inch NPTShaft Diameter 3 inch (76.2 mm) Shaft Rotation Reverse (bi-directional) Oil Capacity 18 US quarts (17 liters) 10W30 standard-duty oil Weight Metallic Heads: 1100 lbs. (499 kg)Fluid End Materials Manifold: Nickel Aluminum Bronze (NAB) 316L Stainless Steel Diaphragm/Elastomers: FKM Buna-N Diaphragm Follower Screw: 316 Stainless Steel Valve Spring Retainer: Polypropylene Check Valve Spring: Elgiloy Valve Disc/Seat : Tungsten Carbide 17-4 Stainless Steel Hastelloy C Outlet Valve Retainer: 316 Stainless Steel Plug-Outlet Valve Port: 316 Stainless Steel Inlet Valve Retainer: 316 Stainless SteelPower End Materials Crankshaft: Forged Q&T Alloy Steel Connecting Rods: Ductile Iron Crossheads: 12L14 Steel Crankcase: Ductile Iron Bearings: Spherical Roller/Journal (main) Steel Backed Babbit (crankpin) Bronze (wristpin)
T80 Series Model T8045 Dimensions
Model T8045 Threaded Version inches(mm)
Front View
Side View
Model T8045 Flanged Version inches(mm)
Front View
Side View
HC-T8045 04.14
www.Hydra-Cell.com
W0507B
29.11(739)
0.75 X 0.75 Keyway (19.05 X 19.05)
3.50(89) Minimum full key
4.83(123)
8.20 (208)
1-1/2 NPT Outlet Both Sides
W0509B
13.43(341)
10.13(257)
5.55(141)
11.55(293)
17.36 (441)
2-1/2 NPT Intlet Both Sides39.64(1007)
W0543A
3.50(89)
29.11(739)
0.75 X 0.75 Keyway (19.05 X 19.05)
Minimum full key
4.83(123)
8.20 (208)
ASME B16.51-1/2” CLASS 2500 RTJ(4x 1 1/8-7 UNC-2B) Outlet Both Sides
W0545A
13.55(344)
10.25(260)
13.39(340)
19.44 (494)
40.89(1038)
14.10(358)
ASME B16.53-1/2” CLASS 300 RF(8x 3/4-10 UNC-2B) Outlet Both Sides
4.80(122)
World Headquarters & Manufacturing1204ChestnutAvenue
Minneapolis,MN55403USA
Tel:(612)332-5681•FAX:(612)332-6937
TollFreeFAX(USAonly)(800)332-6812
Email: [email protected]
www.hydra-cell.com
8&9FleetBusinessPark SandyLane,ChurchCrookham,HampshireGU528BFEnglandTel:+44(0)1252816847 FAXTel:+44(0)1252629242Email: [email protected]
FlatA,21FChathamCommercialBuilding399ChathamRoadNorthHunghom,Kowloon,HongKongTel:(852)3428-6534FAX:(852)3188-9145Email: [email protected]
Wanner Pumps Ltd.
Wanner Pumps Ltd.
Wanner Pumps Ltd.