Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
2
The MARTIN sliding-table saws provide cutting-edge performance for the long-term!Apart from maximum precision and long life, MARTIN offers major components that can be updated as time marches on.
2 x 46° Cutting Angle204 mm Cutting Height
3
MARTIN Sets Standards
Why a MARTIN machine is something
very special
Page 4
The T7PreX
Obtain perfect results automatically
Page 10
Accessories
Individual solutions for
your individual needs
Page 12
4
2 x 46° tilting range for maximum flexibilityWith the possibility of tilting the saw blade of the MARTIN sliding table saw by 2 x 46° it is now up to the operator to decide how to machine a workpiece and not up to the ma-chine. Regardless of whether it comes to the cutting quality, safety or time saving the T75 PreX makes it easy for you to decide which machine you should buy. It is easy to operate and you can decide how you want to set up the machine for the process to be performed.
The advantages at a glanceQuality: With the T75 PreX you don‘t have to turn your work-piece over in order to make an angle cut. From now on the „good“ side will always be the top side. It does not matter whether you process solid wood or panel products; from now on tear-outs on the face side of your workpiece are a thing of the past.
Time: Adjustment and set-up times are reduced to a mini-mum with the T75 PreX. Regardless of whether it comes to time-consuming installation of certain jigs or fixtures or whether you simply need time to decide on how to best per-form a compound cut. The machine is easy to operate and you can adjust it the way it is best suited for the job at hand.
Safety: By keeping control over every step in the process, you minimize the risk of accident for you and your emplo-yees. You don‘t have to use makeshift jigs, fixtures and fences anymore. Just work the way you are used to and the way in which you feel the most secure.
Technology
5
Dual tilting drive With the T75 PreX, MARTIN has revolutionized the concept of the dual-tilting drive of the saw blade. We want you to operate your machine with the precision and accuracy that you are used to when working with a MARTIN. It was espe-cially challenging for our engineers to design a system to precisely adjust the heavy trunnion over a tilting range of 92° to 0.01°. The saw blade arbor is moved from two sides which results in the unique MARTIN DualDrive system. The
CANBus motor evenly transmits power to both sides of the tilting trunnion and positions it extremely accurately via two chain drives that run synchronously. The system is com-pletely resistant to dirt, dust and normal wear and tear. A built-in sensor monitors the angle position and permanently compares it with the values set by the controller. Accuracy that you can count on!
[Photo: DDS]
6
Combinable saw-blade guardsThe patent pending saw-blade guard system of the T75 PreX offers more flexibility and safety to the operator.
Early on in the development process, it was very important to our engineers that the saw-blade guard of the T75 PreX provided good functionality. A saw blade that extends up to 204 mm with a tilting range of 92° has to be covered completely by a wider guard without interfering with the operator‘s work process.
Through the combination of various wide and narrow blade guards, the operator can customize the guards and fit them to the blades angle, thereby increasing dust collection effici-ency.
The guards are symmetrical and can simply be turned around, further reducing set-up times. Both sides of the blade guard can even be equipped with sensors so the con-troller can monitor the allowed cutting angle and saw blade protrusion which creates the perfect zone of protection for the operator.
Technology
7
Sliding table with replaceable table lipThe MARTIN hardened steel guide system, that has been steadily improved since 1959, is part of every sliding table saw. The unbeatable technical advantage of this system is the permanent smooth and precision guidance of the table. Some in our industry view the fact that the hardened steel guide strips are permanently lubricated in oil to be a great disadvantage. On the contrary, it is a testament to MARTIN‘s quality as it is the only way to make sure that the surfaces are unaffected by dust and chips. The hardened guide strips
Cross-cut fence with splinter-free blow-out blockThe T75‘s cross-cut fence has hardly been affected by the doubling of the tilting angle to 92°. You get a premium cross-cut fence that can be pushed back to a safety position when you tilt the saw blade to the left. This way it makes room for the blade guard that now protects this space.Thanks to the clever design of the extension mechanism, its
are cleaned every time the operator strokes the table and is the only way to permanently ensure a smooth and easy movement of the sliding table over time.
The table lip that is bolted to the main sliding table extrusion makes it easy to repair damage caused by deflected saw blades. The table can be locked down every 20 mm along the length of the machine, another MARTIN exclusive!
blow-out block can be used as backing plate regardless of where the fence is positioned. The T75‘s cross-cut fence has a perfect contact surface for short work pieces even if it is pushed back into the safety position. This way your cutting results are always perfect.
8
Touch-screen controller
Modern control system technologyThe T75 PreX is also equipped with the efficient and user friendly touch screen controller, that has been a MARTIN standard since 2006. Step by step, the operator enters all the necessary para-meters and is guided through the process by the controller. All the necessary adjustments are done automatically. This speeds up work and leads to a more intuitive understanding of the machine’s function by the operator.
MARTIN developed the user interface in close cooperation with industrial graphic designers and machine operators. The operating logic is based on what woodworkers need. All relevant information is visible at a glance. The controller always boots up to the „HOME“ page where you get a quick overview on all the important settings like cutting height, cutting angle and fence positions.
Easy to operateTo enter a new value for a particular axis into the controller, just touch the respective number field. The screen immediately changes its input mode, enabling you to enter new numerical va-lues. The numeric keypad not only indicates the minimum and ma-ximum allowable input values that the machine will take, but also memorizes the last five input values for rapid recall. The integrated calculator can also be used if necessary. On the „HOME“ page, ra-pid access icons can be created and unused icons can be deleted. This way you can keep track of the current machine values.
For the precision calculation of your cuts and quick tool change you can store up to 100 different saw blades in the tool menu. A saw blade that has been stored once is immediately available and fully integrated in the controller. This way the 3-axis scoring unit automa-tically adjusts to the kerf of the main saw blade. Time consuming test cuts can be omitted almost completely and you can concentra-te on the task at hand.
Powerful assistanceFor performing special work on a sliding table saw like cutting groo-ves, rabbets and tongue-and groove joints, the MARTIN controller offers an efficient assistant. Step by step the operator enters all the necessary parameters and is guided through the work process by the controller. This way even untrained machine operators soon become experts.
Clearly arranged - the „Home“ page
Integrated tool conversion
Step by step cutting aid
Technology
9
Calculating for expertsThe MARTIN controller also supports you when you have to calcu-late angle cuts, false mitre cuts or even specialized cuts for making European-style benches. With these intuitive calculation tools, even complex calculations can be made right the first time. You simply enter the measurements of the workpiece in the controller and it calculates the correct values for you.
Always up-to-dateA MARTIN machine is a safe and long-term investment since its controller can be updated as time marches on. We at MARTIN are continuously improving our software. The controllers can be up-graded in field with an USB stick. This way you always have access to new cutting aids or updates of existing applications.
A profile for every individual userCustomization of the controller is possible for over 25 languages using Latin/Cyrillic character sets. By defining individual user profiles (up to 10 depending on the size of the controller) the controller can not only be adapted to different languages but also to the professional experience of the individual machine opera-tors. Different user profiles can be password protected so each machine operator can get restricted or unrestricted access to the menu items. This password protection of the user profiles prevents misuse by untrained employees increasing job safety and leading to more accurate results.
Support from the officeThe machine can be connected to a computer by an optional data interface. This way the T75 PreX can be connected to the MARTIN editor or to other panel-cutting optimization software programs like ARDIS®, Boole&Partner®, Vlecad®, CAD-code® or PatternSystems®. With the optional CPOUT interface you can connect your machine to almost every software you like to use. This way the machine opera-tor is guided through the work process very efficiently which leads to more accurate results and efficient use of the resources at hand.
Calculating quickly and easily
More security by individual user profiles
Panel optimisation - no problem
10
T75 PreX
The T75 Classic: The classic for your workshop
The T75 PreX is a high-end sliding table saw that sets new standards for the wood-working industry. It is the first machine worldwide where a cutting height of more than 200 mm is combined with a tilting range of 2x 46°. Thanks to numerous inno-vative solutions, the operator has the free-dom to execute each angular cut at the cross-cut fence and at the rip fence ex-actly the way it is best for the task at hand or the workpiece to be machined. Now it is simply up to the operator to decide how to machine a workpiece and not up to the ma-chine.
Powerful cut up to 204 mm in heightA powerful 7.5 kW motor that can also be equipped with a variable speed control ma-kes certain that the remarkable cutting height of this machine can be used effici-ently. Refinements like increased motor hor-sepower of up to 11 kW (15 HP) and a cut-ting angle with an accuracy of 0.01 degrees are things that you can expect from MARTIN. The T75 offers a tilting range of 92°, thanks to the new dual sided driven trunnion system that can be quickly positioned.
Clear and comfortable operationDesigned into the premium class T75 PreX is MARTIN’s user friendly and intuitive touch-
screen technology. Not only does MARTIN set industry standards with their mechani-cal engineering but also with their operating system. The adjustment of the machine by the operator is achieved with an intuitive di-alog with the controller. From the saw blade to the rip fence to the 3-axis scoring saw, all axes are automatically adjusted. The machine’s software is constantly being improved upon. Offered updates are easily downloaded by the customer and uploaded to the machine. A MARTIN machine always offers the best resale value, because no one wants to be stuck with an outdated control-ler with outdated software.
204 mm Cutting height Operation at a glance Automatic lowering of the rip fence
T75 PreX with accessoriesT7502 Motor power 7.5 kW (10 HP) variable rotational speed controlT7509/2 Cutting width 1100 mmT7510 10.4“ (264 mm) touch screen controlT7535 Mitre cross cut tableT7550 „RadioCompens“mitre cut system, 2-point fenceT7513 Additional saw blade guard 60 mmT7511 Motorized positioning of rip fenceT7523 3-axes scoring saw unitT7567 Front support tableT7574 Pneumatic lowering of rip fence below table level
11
Safety and Comfort A special design feature of the T75 PreX is the outstanding function of the blade guard. The guard is designed to function with a saw blade height of 1 mm to 204 mm and with a tilting range of 92°, without being a con-stant nuisance to the operator. Through the combination of various wide and narrow blade guards, the operator can customize the guards and fit them to the blade’s angle, thereby increasing dust collection efficiency. The guards are symmetrical and can sim-ply be turned around, further reducing set-up times. Both sides of the blade guard can even be equipped with sensors so the con-troller can monitor the allowed cutting angle
and saw blade protrusion which creates the perfect zone of protection for the operator.
Flexibility at the highest levelWith the decision to purchase a T75 PreX, you are deciding on a reliable, premium class machine that ideally fits the versatile requirements of your daily work. Whether you cut square panel products, saw complex angular cuts in solid wood or process glued up stock, thanks to the T75 PreX’s strong flexibility you can achieve perfect results. With a tilting range of 92° and a blade height of 204 mm, you have new possibili-ties to revolutionize your work. Now you can decide how best to process your workpiece, not the machine.
Motor power: 7.5 kW (10 HP)
Saw-blade tilting: -46° to +46°
Cutting height: max. 204 mm (8“)
Saw-blade diameter: 250 – 550 mm (10” - 21,6”)
Rotational speed: 3800 rpm
Standard Cutting width: 850 mm (33-1/2”)
Standard Sliding-table length: 3000 mm (9’ 8”)
Weight: 1600 - 2100 kg (3,500 - 4629 lbs.)
12
Accessories
Standard cross-cut table
The light and sturdy MARTIN cross-cut table is a standard component of all
T75 PreX saws. It can be easily clamped with one hand to any point along
the whole length of the sliding table. The outboard table support roller
simplifies the moving of larger workpieces and prevents damage to delicate
panel surfaces. The cross-cut fence can be positioned in either the forward
or rear position on the cross-cut table, enabling the stops to be positioned
quickly for the task at hand. The large angle scale integrated into the table
The T75’s standard cross-cut table
allows accurate angled cuts to be made between 0° and 50° by a simple
adjustment of the cross-cut fence. The fixed angle detents integrated into
the table facilitate the rapid cutting of common angles (22.5°/30°/45°).
The exact compensated calculation of the miter cut is performed by the
controller. By entering the workpiece width and angle, and the desired
length into the controller, the operator is prompted to make the adjustment
to the stop.
Standard fixed angular detents
Standard analog 2-point cross-cut fence
Analog and digital 2-point cross-cut fences
All T75 PreX machines are equipped with the proven MARTIN 2-point cross-
cut fence as standard, which allows both solid wood or man made panels
to be aligned at two points along the fence extrusion. This system enables
panels with even slightly concave edges, caused by internal tension, to be
cut accurately. The magnifying glass, an easy-to-read scale and standard
fine adjustment of the 2-point stop element ensure accurate cuts from 255
to 2025 mm. The 2-point stop’s clamping element design allows the ope-
T7540 digital 2-point cross-cut fence
rator to rapidly make adjustments with little effort. Lengths up to 3365 mm
can be cut using the extendable outboard stop. If you prefer working with
digital readouts, the T7540 digital cross-cut fence may be the right choice
for you. Both the inner and outer stop use separate measuring devices and
can be set independently from each other with an accuracy of a tenth of
a millimeter. Read-outs can be switched to a relative measurement mode,
which is especially helpful when making incremental cuts.
1313
Miter cross-cut table
With the digital angle display integrated in the table, mitre cuts can be
set easily and accurately. The table offers full support of the workpiece
at every angle. The table and fence move with the MARTIN parallelogram
table design, not just the fence. The table is unlocked by actuating a handle
under the table allowing it to be adjusted within a range of ± 46.50° via an
LCD display. Other important features are the table‘s beefy 0° lock and the
angular fine adjustments allowing the operator to make changes in 1/100°
T7535 Miter cross-cut table
increments. The innovative MARTIN „Radio-Compens“ angle cutting system
in conjunction with the miter cross-cut table and motorized crosscut stop
creates a whole new vision of productivity for tomorrow’s woodworkers and
cabinetmakers. Set-up times for angled cuts can be reduced by more than
80%. You simply set the miter cross-cut table, which is connected to the
controller via a bus line, to the desired cutting angle. The radio-controlled
electronics take care of the rest.
Analog and digital continuous contact cross-cut fences
The MARTIN 2-point cross cut fence system offers many unique and
superior operating characteristics to the custom woodworker. Alas, at first
not everyone feels comfortable with this system. For those who prefer the
more traditional flip stop, the T75 PreX can be equipped with a continuous
contact cross-cut fence . This system is useful, especially if you work a lot
with thin, flexible material. The straightened material is aligned seamlessly
along the fence making for a precise cut every time. The stop element
closest to the blade can be adjusted accurately with the fine adjustment in
T7537 Analog continuous contact cross-cut fence
relation to the scale and magnifying glass. The stop element’s quick clamp
facilitates a rapid stop adjustment from 280 to 2045 mm. Lengths of up
to 3320 mm can be cut using the outboard extendable stop. The digital
variant of the fence provides maximum accuracy. Two easy-to-read LCD
displays operate independently from each other and the measurements
are displayed with an accuracy of 0.1 mm. Read-outs can be switched to a
relative measurement mode, which is helpful to the operator when making
incremental cuts.
T7541 Digital continuous contact cross-cut fence
T7550 „Radio-Compens“ angle cutting system
14
Multi-purpose table
The multi-purpose table is ideal for customers who do primarily the parallel
cutting of large panels as well as smaller strips. A hand wheel allows the
operator to move two stops at the same time and parallel to one other. The
workpiece is positioned precisely against the stops and is then introduced
into the saw cut. The multi-purpose table ensures that damage to delicate
decorative edges and the marring of the panel’s surface is virtually elimina-
ted. Panels up to 2100 mm in width can be easily and accurately processed
T7558 Multi-purpose table
simply raising or lowering the stops. If the stops are lowered completely
below table level, it enables you to move very large panels unobstructed on
the table. The LCD display for the cutting width also enables the incre-
mental movement of the stops. Even cuts to the right of the saw blade are
precise, since the thickness of the saw-blade is always referenced by the
controller. The beefy floor mounted track system makes the multi-purpose
table ideal for even the heaviest of workpieces.
Digital display of the cutting width
T7590/5 Acrylic Polishing Device
Accessory to finish polish the edges of Polymethacrylate (Acrylic)
Woodworkers that process plastics as well as wood will be the ones that
will benefit the most from the combination of a sliding table saw and a
polishing machine. The advantage of this MARTIN option over stand-alone
polishing machines in this price range is the gentle and firm clamping and
exact guidance of the workpiece. Even edges of up to a length of 3000 mm
can be polished safely and cleanly with the required accuracy in only one
run. The machine is equipped with a powered sliding table that allows the
operator to dial in a feed speed for perfect results. The machine includes
a newly designed pressure bar that is divided up into several clamping
Polishing edges of up to a length of 3,000 mm
areas which can be used independently. The clamp ensures gentle and
firm clamping of workpieces both big and small. The special rip fence that
is included in the package makes it easier to position the workpieces that
have to be polished. Even whole stacks of acrylic panels can be positioned
for polishing without difficulty at the 2 m guide. Acrylic panels as well as
whole stacks of the material with an edge length of up to 3000 mm and a
thickness of up to 100 mm can be processed effortlessly with this innova-
tive patent pending solution in your own workshop.
Accessories
15
Electrically adjustable 3-axis scoring saw unit
The patent pending 3-axis scoring saw unit is fully integrated in the con-
troller and facilitates the input of all necessary settings. The 3-axis scoring
height, relation to main blade and kerf width are positioned automatically.
Thanks to a quick clamping system the scoring unit can be completely re-
moved or changed within seconds. Time consuming procedures are avoided
almost completely.
On/Off switch for main saw and scoring saw unit
With this accessory you can start the machine from any position along the
sliding table. It can be positioned without having to use a tool and offers a
high degree of flexibility to the operator. Big panels can be positioned and
then the machine can be started easily from the operating position.
T7523 Electrically adjustable 3-axis scoring saw unit T7577 On/Off switch for main saw and scoring saw unit
T7571 motorized sliding-table
Motorized sliding-table
The motorized sliding-table offers the woodworker precision cuts through
its even feed motion. The controlled feeding of the workpiece also provides
the optimum mix of feed rate and cut quality. Man-made materials such as
plastics or non-ferrous metal sheets can be safely cut with the motorized
sliding-table. The T7570 pneumatic pressure bar is an ideal addition to
the motorized sliding-table system, providing positive clamping of the
Focus on the control element
workpiece through the controlled cut. The table’s feed rate can be infinitely
adjusted from 0 to 25 m/min via a speed potentiometer. The table can also
be switched on and off in seconds via the selector switch. When the system
is switched off the drive is shut down immediately. Since the drive’s control
unit is located on the side of the machine, this enables the operator to use
practically the full length of the sliding table at all times.
1616
Pneumatic pressure bar
MARTIN now offers a technically improved pressure bar for your sliding
table as a further innovation to upgrade your sliding table saw. Cutting thin
boards, plastic laminate or veneer is no problem at all anymore. A clamping
height of 100 mm and a clamping pressure of 800 N (psi) make it possible
to process large workpieces safely and accurately. The pressure bar can
also be used in combination with the existing cross-cut fence on your saw
T7570/3-b Pneumatic pressure bar
to position a workpiece accurately. The fence can be positioned in the front,
rear or between the individual clamping elements. Angular cuts are also
possible. You simply lift the clamping elements you do not need (optional).
For quick and intuitive handling the pressure bar is equipped with an end-
to-end tool bar. This way you can operate from every position at the sliding
table.
Clamping elements offer greater flexibility
T7565 Roller support for standard cross table
Roller Support
To make use of the full movement range of a
sliding table of over 3.7 m or to handle very
heavy material, MARTIN recommends using the
roller support. The support runs on a floor
mounted track with integrated wipers to keep
the track clear. The roller support is a standard
feature of the T7558 multi-purpose table.
T7573 Laser light for indication of cutting line
Laser light for indication of cutting line
The laser beam indicates the exact cutting line,
which is particularly useful for trimming and
straight-lining solid wood. The cutting of workpi-
eces according to layout lines is a typical
application for this device.
T7568 Second support with T7555 parallel cutting stop
Second support and parallel cutting stop
The second support assists the operator in the
truest sense of the word. Simply attach it to the
sliding table for easy handling of large panels.
The workpieces are safely supported by the 600
mm long support and can be indexed against the
optional parallel cutting stop, when ripping long
material with the sliding table.
Accessories
17
T7567 Front support table
Front support table
Long, narrow workpieces can be cut more efficiently by using a suitable
support table. The foldable front support table helps to guide the workpiece
safely along the rip fence.
T7572 Edging device
Edging device
The cutting of overhang on veneered or laminated panels is just one of the
many applications for the edging device. Simply attach this device to the
rip fence. This device can also be used for straight lining solid stock as a
substitute for a laser.
T7533 DGA 900 Top Digital Double miter fence
Double miter fence
Thanks to the easily understandable adjust-
ments of the DGA 900 Top, workpieces of
different widths can be joined quickly and easily.
Mitered glazing beads for intricate angled
windows and arches can be cut using the DGA
900 Top with perfect results.
T7580 Spraying device for the main saw blade
Spraying device
With the spraying device, even plastic or non-fer-
rous metals can be cut easily. The spraying heads
spray both sides of the saw blade with a coolant
or lubricant. The lubricant container and the pneu-
matic unit are mounted in an easily accessible
area for the operator.
T7539 Additional stop element for the T7540 cross-cut fence
Additional stop element
All cross-cut fences with 2-point alignment and
those with continuous contact can be equipped
with an additional stop element. This aids the
operator, because this enables two different
measurements to be cut without changing the
setting.
18
Technical specifications
A
DC
L
F
A
Technical specifications
Motor power 7.5 kW (7.5 HP)
Optional 9.5 kW / 11 kW (12 HP / 15 HP)
Cutting height max. 204 mm (8”) / saw blade Ø 550 mm / 0°
Saw-blade tilting +46° to -46°
Saw-blade diameter 250 – 550 mm (10” - 21.6”)
Rotational speed 3.800 rpm
Optional Infinitely variable from 2.000 to 6.000 rpm
Main saw blade change ProLock
Blade thickness max. 6 mm (15/64“)
Cutting width 850 mm (33-1/2”)
Optional 1100 / 1350 / 1600 mm (43.3“ / 49.2“ / 63“)
Cross-cut fence length 255 – 3365 mm (10” – 132,5”)
Standard Sliding-table length 3.0 m (9’ 8”)
Optional 1.9 / 3.3 / 3.7 / 4,3 / 5.1 m (6’ 3”, 10’ 10”, 12’ 7”, 14‘ 2“, 16‘ 7“)
Controller PowerPC
Control panel Touch screen, colour; TFT 5.7” (145 mm)
optional Touch screen, colour; TFT 10.4” (264 mm)
Cutting angle / height / width controlled
Cutting width according to scale, optional digital display or controlled
T75 PreX
340 (13,4“)A402 (15,8“)108 (4,2“)
900
(35,
4“)
600
(23,
6“)
510
(20,
1“)
865
(34“
)
900
(35,
4“)
550 (21,6“)
740
(29,
1“)
1504
(59,
2“)
DC
L
F
590
(23,
2“)1375 (54,1“)
340 (13,4“)
340 (13,4“)A400 (15,7“)
255 - 3440 (10“ - 132,5“)
2165 - 3515 (85,2“ - 138,4“)
19
T7535
F
L
CD
A
T75 PreX
Technical specifications
Display resolution 0,1 mm and 0,01°
Dust port - machine frame Ø 120 mm (4-3/4”)
Dust port - blade guard Ø 100 mm (4”)
Weight approx. 1,600 - 2,100 kg
A = cutting width [mm] F = passage width [mm] Sliding-table length L [mm] Format cut [mm]
850 (33-1/2”) 930 (36,6”) 1900 (6’ 3”) 1900 x 1900 (6’ 3” x 6’ 3”)
1100 (43-1/4”) 930 (36,6”) 3000 (9’ 8”) 3000 x 3000 (9’ 8” x 9’ 8”)
1350 (53”) 930 (36,6”) 3300 (10’ 10”) 3300 x 3300 (10’ 10” x 10’ 10”
1600 (63”) 930 (36,6”) 3700 (12’ 7”) 3310 x 3700 (10’ 9” x 12’ 7”)
4300 (14’ 1”) 3310 x 3700 (10’ 9” x 12’ 7”)
Movement range C [mm] Movement range D [mm]
2500 (9’ 2”) 2400 (7’ 10”)
3600 (11’ 9”) 3500 (11’ 5”)
3900 (12’ 11”) 3800 (12’ 5”)
4300 (14’ 1”) 4200 (13’ 9”)
4900 (16’ 1”) 4800 (15’ 7”)
Low dust emission according to BGI 739, appendix 4.
Please refer to the latest price list for current
details about the machine specifications and
equipment.
All dimensions are in millimeters / inches.
Manufactured in Germany
Dimensions and technical
data are subject to technical
innovation and may be
changed without notice.
Illustrations can deviate from
the original.
T7535
ø 100 (3,9“)
ø 120 (4,7“)
110
(4,3
“)
165
(6,5
“)
315
(12,
4“)
395
(15,
6“)
1601
(63“
)
150
(5,9
“)
750 (29,5“)
742
(29,
2“)
590
(23,
2“)
1504
(29,
2“)
F
L
CD
255 - 3365 (10“ - 132,5“)
2165 - 3515 (85,2“ - 138,4“)
340 (13,4“)
340 (13,4“)400 (15,7“)
1000 (39,3“)
A
1350 (53,1“)
854 (33,6“)
4000
Rie
der
07/1
1
Otto MARTIN Maschinenbau GmbH & Co. KG
Langenberger Str. 6
87724 Ottobeuren
Germany
Phone +49 (0) 8332 911- 0
Fax +49 (0) 8332 911- 180
www.martin.info