SVX8004G IP-PBX User Guide_20080611.pdf

www.star-net.cn

- 1 -

SVX8004G IP-PBXUser Guide

1. Introduction

1.1. Overview

SVX8004G is an all-in-one converged communications solution ideal for small businesses.The product offers full PBX functionality, including VoiceMail, Auto Attendant, Hunt Group,Ring Group, Call Transfer, Call Forward and much more, which help businesses reducecommunications costs and stay connected everywhere.

www.star-net.cn

- 2 -

SVX8004G is a hybrid telephone system capable of handling both traditional telephoneand Voice over IP calls. Using VoIP allows calls from one location to be routed over theInternet to another location, eliminating long distance charges. SVX8004G can alsodirectly integrate with VoIP service provider networks.

SVX8004G is very easy to understand, configure, and deploy. The web interface isdesigned to provide a clean and user-friendly configuration window so that users wont getlost in complicated menus and maintenance. A fully working system can be set up quicklyand be ready to communicate.

1.2. Capacity

The system has the following capacity:

l 1 Analog line + 1GSM interface + 2 Analog Extensions

l 30 VoIP extensions

l 4 VOIP lines

1.3. Features

Full Range of PBX Features

SVX8004G offers a full range of traditional PBX features like Call ID, Call Forward, CallTransfer, Call Waiting and more. All such features are available to both analog and VoIPextensions.

Auto Attendant

SVX8004G handles inbound calls with an auto attendant. Auto attendants answer allincoming calls. Play a recorded message and route callers to their requested destinations.All voice prompts are fully customizable.

Call Queue

Call Queue holds incoming calls when all members are busy assisting other callers. Callswait in the call queue for the next available member. While calls are waiting, they hear themusic-on-hold. Calls are distributed out of the call queue on a first in, first out basis, asmembers become available.

www.star-net.cn

- 3 -

Call Back

The user can call to the PSTN line port and hang up after 3 rings. Then the SVX8004G willcall back to the user and play two-stage dialing tone, and then the user can makeinternational calls via the Internet with cheap rates.

SMS Call Back

SVX8004G can provide the callback function based on SMS. Calling party can send textmessage according with SMS setting rule to GSM. GSM will callback to callingparty after the message was received, and call forward to called party via PSTN, in orderto build a communication between both parties.

SMS sending by SMTP/POP3

SVX8004G can receive and send Mobile text message in sharp of Email. User canreceive text message sent to GSM through those Email software (such as Outlook orFoxmail), they can also send Email via GSM, then the Email can be received as textmessage form by Mobile.

Voicemail

The voice mail feature allows messages to be recorded when a particular extension cannot be answered. It is also possible to send particular calls to a voice mail box directly.Voice mail messages are recorded in wav format and stored in the users mailbox andoptionally forwarded by email to the user.

Automatic Route Selection

SVX8004G gives you complete control over your phone lines and extensions. You canautomatically place specific types of calls on specific lines.

Line Hunt Group

Line Hunt Group consists of analog or VoIP lines that are associated so that calls to anyline in the group are rolled over to the next available line in the group when the line is busy.You can move lines within a line group to set the hunt order.

Extension Ring Group

Extension Ring Group is a collection of users. For example a group to handle all sales

www.star-net.cn

- 4 -

related calls. An incoming caller wishing to speak to sales can be directed to that group,where the call can be answered by any member of the group who is available.

1.4. Software Specifications

ProtocolSIP RFC3261SDP RFC2327RTP/RTCP

Codec G.711 /G.729

ExtensionAnalog ExtensionIP Extension

Billing SupportCall Detail RecordPolarity Reversal Detection / Generation

Line

PSTN LineGSM LineFXO GatewaySIP RegisterSIP Trunk

Configuration WEB Browser / IVR / Keypad

Firmware Upgrade HTTP / FTP

1.5. Hardware Specifications

Network Interface Two 10/100Mbps Auto-Negotiation RJ45 portsAnalog Interface 2 RJ11 analog portsGSM Interface Quad-band GSM 850/900/1800/1900 MHZ

PowerAC Input: 100~240V AC, 50/60HzOutput: DC12V/1A

EnvironmentalConditions

Operational temperature: 0~40?Storage temperature: -10 ~? 60?Humidity: 10%~90%, no coagulation

Dimensions and WeightSize: 187(W) x 138(D) x 38(H) mmNet Weight: 0.35Kg

2. Installation

2.1. Safety PrecautionsBefore using SVX8004G, please review and ensure the following safety instructions areadhered to:

www.star-net.cn

- 5 -

1) Read, follow and retain instructions All safety and operating instructions should beread, followed and retained for future reference before operating the equipment.

2) Heed warnings All warnings on the equipment and in the operating instructionsshould be adhered to.

3) Temperature Do not operate in environments where the temperature is below 0Cor 32F. If the product was shipped in cold weather, please let the system warm up atroom temperature for at least two hours before plugging it in to a power outlet.

4) Moisture Do not place SVX8004G in a high-humidity environment.5) Heat Never place SVX8004G near heat sources such as radiators, floor registers

or in direct sunlight. Do not stack units on top of each other.6) Power supply The equipment should only be connected to an approved power

supply of the type described in the operating instructions or marked on the equipment.Use only the power adapter supplied with SVX8004G.

7) Damage requiring service Do not attempt to service the SVX8004G yourself.Unplug SVX8004G and refer servicing to a licensed technician when:l The plug or power cord has been damaged.l SVX8004G has been exposed to moisture.

2.2. Check Package ContentsEach SVX8004G package should include the following:

Name QuantitySVX8004G unit 1RJ-11 telephone cable 1 for each phone portRJ-45 Ethernet cable 1AC adapter 1Quick installation guide 1

2.3. Ensure You Have the Followingl One computer with Ethernet network interfacel One analog telephone

2.4. Front Panel

The front panel consists of several lights and ports:Power Indicates the power status. The power is on when Power light is lit.Status Indicates the system status. The light will flash for a few moments during

www.star-net.cn

- 6 -

boot-up, and then remain lit, indicating the device is on.Eth0 Indicates the LAN port connection status, The LAN is connected correctly if

the Eth0 light is lit.Eth1 Indicates the PC port connection status, The PC is connected correctly if the

Eth1 light is lit.Ext1 Indicates the usage of the onboard extension 1. The light is lit when the

extension is ringing or off-hook.Ext2 Indicates the usage of the onboard extension2. The light is lit when the

extension is ringing or off-hook.Line Indicates the usage of the onboard lines. A Line is occupied if the indicator

light is lit.

2.5. Back Panel

Line The Line connectors are RJ11 ports used for connecting incomingtelephone lines.

Ext1/Ext2 The Ext1 and Ext 2 connectors are RJ11 ports used for connectingphones and other analog devices.

ETH0 The Eth0 connector is an RJ45 port used for LAN networking, andVoIP capability.

ETH1 The Eth1 connector is an RJ45 port used for unit configuration via PC.RST The RST button is used to reset all parameters to the factory default.Power The power connector is a receptacle rated at 12VAC/1.5A for

connecting the supplied AC adapter input line, with a power switchbeside.

GSM The antenna connector of the GSM card.

www.star-net.cn

- 7 -

2.6. Connect the Device

2.6.1. Connect diagram

2.6.2. Connect the powerPlug the DC end of the power adapter to the power socket on the device and the otherend to an available power outlet. Switch the power control which is located at the backpanel of the SVX8004G to ON position and then the power indicator will light up indicatingthe device is on.

WARNING!

n Never use a power adapter other than the one provided with SVX8004G.

2.6.3. System StartupThe status light on the front panel will flash for a few moments during boot-up, and thenremain lit, indicating the device is on.

2.6.4. Connect the networkConnect the RJ11 port on the device to a Router/Switch by cable. The LAN indicator willlight if connected correctly.

www.star-net.cn

- 8 -

2.6.5. Connect the computerConnect a computer to the same Switch or Router as SVX8004G, so the SVX8004G canbe accessed through the network.

2.6.6. Connect the telephoneConnect one end of the provided RJ-11 telephone cable to the phone jack and the otherend to your phone. You can hear some signal tones from the earpiece when you pick upthe telephone handset.

NOTE:

l The signal tone cannot be heard from the handset before the booting process iscompleted. The status light on the front panel will flash for a few moments duringboot-up and then remain lit, indicating the device is on.

2.6.7. Connect the PSTN lineConnect one end of the RJ-11 telephone cable to wall phone jack of an incoming phoneline and the other end to the line jack at the back of the SVX8004G.

WARNING!

l Never connect the line to the phone jack. Otherwise, the device may be damaged.

3. Configuration

3.1. Initial Configuration

3.1.1. Get the device IP addressPickup the phone connected on the Ext port, dial *100#, and then follow the voiceinstruction. Press 0 key to listen to the IP address of the device.NOTE:l You may not hear the voice from the phone if the device is still in booting process. TheSTS light on the front panel will flash during boot-up, and then remain lit, indicating thedevice is on.

3.1.2. Login into the Web interfacel Make sure your computer is in the same subnet with the device by modifying your

computers IP address to match the devices IP address.

www.star-net.cn

- 9 -

l Start web browser. Enter the IP address of the device into the address bar. The loginpage will appear:

l Enter the user name and password to login, the default user name is admin, andpassword is admin.

NOTE:l We strongly advice you to change your password when you first login to avoid any

unnecessary loss. You can press and hold the Reset button on the back panel for afew seconds to reset to factory default if you have forgotten or lost the password. Beaware that all the parameters you set before will be lost if you do so.

3.1.3. Web interface overviewAfter successful login, the desktop screen will appear.

l Online Help center Click this icon to enter the online help center of SVX8004Gl Application Manage Add, remove or update the application or software.l Control Panel Change the password for the login account, modify system time and

check the system information.l Network Settings All network related configurations.l Return to desktop Click this button to return to the desktop at any time.l IPPBX Configuration Click this icon to enter the IPPBX configuration interface.l Reboot Reboot the device.l Exit Logout from the desktopl System Time Shows the current time of the system.

3.1.4. Network SettingsThis screen lets you configure the network connections.

www.star-net.cn

- 10 -

Click the LAN icon, the LAN Settings screen will appear. User can change the IP addressand DNS server address for the LAN port here. Devices MAC address is shows in theMac Address section.

3.1.5. Control Panel

This screen lets you change password for the login account, modify system time andcheck the system information.

Check the system information:

www.star-net.cn

- 11 -

Change the login password:

Set system Time:There are two ways to set the system time:Set as PC Time: Click this button, the device will synchronize time with your PCimmediately.Through NTP Server: Tick the option Auto Synchronize with Internet NTP Server.The device will automatically synchronize time with the NTP server periodically. Youshould select the time zone where the device reside and input the address of the NTPserver. Click the button synchronize now! will let the device synchronize time with theserver immediately.

www.star-net.cn

- 12 -

Edit system service parametersIn System Services section, you can edit the HTTPD service parameters

Click link thttpd, following screen will appear. You can change the listen port and thelogin timeout of the HTTPD server. If there is no action performed after the timeoutspecified here, the Web screen will return to the login page.

DiagnosticEnter a destination hosts IP address or domain name into the text area next to Pingbutton and click the Ping button, device will try to ping that address and print the returnedmessage in screen.

www.star-net.cn

- 13 -

Debug ToolsEnter a destination hosts IP address or domain name into the text area next to Pingbutton and click the Ping button, device will try to ping that address and print the returnedmessage in screen.

Delete log data Delete the saved log data.Startup Type Specific how to start the debug. Device will start the debugautomatically when boot up if Automatic is been selected. User need click start buttonat below to start debug if Manual is been selected.Service Status Show the status of the debug mode.Duration Specific the debug duration, debug will automatically stop after theduration.Star time Device will start debug automatically at the specified start time.Module Settings Specific what kind log information will the debug catch, please adjustthe parameters according to the advice of the technical supporter.

3.1.6. Application ManageThis screen lets you add or remove application and update the system software.

www.star-net.cn

- 14 -

To remove application, just click the Delete button under the application name which youwant to remove.

A new application can be added to system by installing from an installation package file.

A patch could be patched to fix some minor bugs or perform some minor update to thefirmware.

The whole system, including the embedded Linux operation system, can be updated byreprogramming the flash. Just select the appropriate binary file and click Upgrade tostart.

WARNING!

l The updating process may take a long time. Never power off the device during theupdating, otherwise the device might be damaged permanently.

www.star-net.cn

- 15 -

3.1.7. IP-PBX Configuration InterfaceClick the SVX8004G icon on the desktop, the IP-PBX configuration interface will appear.In this interface, you can do all the configurations related to the IP-PBX functions.

In IP-PBX configuration interface, If you want to return to desktop screen or logout, justclick the link at the top right of the screen at any time.

You can click the button Activate Changes to reload the IP-PBX service withoutrebooting the device.NOTE:l Only one CODEC type is supported by SVX8004G at a time. If you want to change toother CODEC type, you should update the firmware to corresponding version.

3.2. Configure ExtensionsSVX8004G supports up to 32 extensions including 2 onboard analog extensions and 30IP extensions.

3.2.1. Configure Onboard ExtensionsClick the Extensions menu, and Onboard Extension submenu. The Onboard Extensiontable will appear. You can edit the parameters of each Ext port by selecting Ext1 orExt2

www.star-net.cn

- 16 -

l Number The telephone numbers of the 2 onboard Ext ports are fixed to 101 and102. The user cannot change these.l Display Name A description name for memorization. When calling from thisextension to another IP phone, the name will be displayed on the LCD screen of thephone as the caller name.l Three Way Call Enable or disable the threeway call function on the selectedonboard extension.l Enable SIP Reg. Enable or disable the registration of a SIP Phone. Default is OFF.l Keep Alive Select ON to allow device to check if the extension is reachable. Defaultis OFF.l Auth ID The authorization ID used to register to IPPBX.l Secret The password associated with the Auth ID which will be used by the IPextension to register to the IPPBX.l VoiceMail Select On to activate the voice mail box for the extension or Off todeactivate it.l Email Notification Specific an Email address. An email will be sent to that emailbox whenever this extension has a new voice mail message.l SMS Notify Number Specific a mobile phone. A message will be sent to that mobilephone whenever this extension has a new SMS message.NOTE:l Parameters with a * mark are mandatory. A value must be specified beforesubmitting.l Parameters with a blue color are optional. The value can be specified or not.

Click OK to submit or Cancel to abort the change.

If any parameter is changed in the IPPBX, three buttons will appear on the top of thescreen. Click Save & Reload to save the changed parameter to flash and restart theIPPBX service to make the changed parameter take effect immediately.

www.star-net.cn

- 17 -

Click Save to save the changed parameter only to flash. It will not take effect until thenext restart.

Click Abort to abort all the parameter changes since the last saving.

3.2.2. Configure IP ExtensionsClick the Extensions menu, and Add IP Extension submenu. The Add IP Extensionscreen will appear. You can create an SIP account here.

l Number (3-16)The telephone number of an IP extension can be any number lengthbetween 3 and 16.l Auth ID The authorization ID used to register to IPPBX.l Secret The password associated with the Auth ID which will be used by the IPextension to register to the IPPBX.

www.star-net.cn

- 18 -

l Display Name A description name for memorization. When calling from thisExtension to another IP phone, the name will be displayed on the LCD screen of thephone as the caller name.l Keep alive Select ON to allow device to check if the extension is reachable. Defaultis OFF.l VoiceMail Select On to activate the voicemail box for the extension or Off todeactivate it.l Email Notification Specific an Email address. An email will be sent to that emailbox whenever this extension has a new voice mail message.l SMS Notify Number Specific a mobile number. A message will be sent to thatmobile phone whenever this extension has a new SMS message.

Click OK to submit and then click Save & Reload to take immediate effect.

After adding an IP extension, the created SIP account can be configured to an IP phone,ATA, voice gateway or any other SIP compliant device and then registered to SVX8004Gas IP extensions.

3.2.3. Extension StatusClick the Status menu, and Extension Status submenu. The Extension Status table willappear. The status of all the added extensions is listed here, including the 2 onboardanalog extensions. You can click the Extension Status submenu again to refresh theinformation

www.star-net.cn

- 19 -

Extension status:l IP Address The IP address from which the IP extension is registered to SVX8004G.l Port The port associated with the IP address for registration.l Status Shows the calling state for onboard analog extensions and shows theregistration state for IP extensions.l Service(s) Shows the activated services of this extension. Each small iconrepresents a service. User can check the detailed information by pointing the cursor to it.Extension Services:Click the EXTENSION SERVICES to expand the page.l Extension Select an extension to modify.l Calling Display Select Enabled to display the caller ID when making calls.l Call Waiting Select enabled to enable the call waiting service. A beep will be heardif a call comes in when this extension is already in a communication.l Do Not Disturb Select Enabled to enable the do not disturb service. All incomingcall will be rejected automatically by the device and the phone connected to the extensionwill not ring when this service is activated.l Unconditionally call forward Specific a phone number here and all incoming callswill be forwarded to that number automatically. To deactivate this service, just delete thenumber specific in this section.l Call forward when busy Specific a phone number here, all incoming calls will beforwarded to that number automatically when the extension is busy. To deactivate thisservice, just delete the number specific in this section.l Call forward if no answer Specific a phone number here, all incoming calls will beforwarded to that number automatically when the extension does not answer the call. Todeactivate this service, just delete the number specific in this section.l Call forward if unavailable Specific a phone number here, all incoming calls will beforwarded to that number automatically when the extension does not register to the device.To deactivate this service, just delete the number specific in this section.

3.2.4. Add IP Extension GroupClick the Extensions menu, and Add IP Ext. Group submenu. The Add IP Extension

Group screen will appear. You can create a group of SIP account here.

www.star-net.cn

- 20 -

l Number Begin (3-16) The beginning telephone number of an IP extension can beany number length between 3 and 16.l Number End (3-16) The ending telephone number of an IP extension can be anynumber length between 3 and 16.l Auth ID The authorization ID used to register to IPPBX.l Secret The password associated with the Auth ID which will be used by the IPextension to register to the IPPBX.l Display Name A description name for memorization. When calling from thisExtension to another IP phone, the name will be displayed on the LCD screen of thephone as the caller name.l Keep alive Select ON to allow device to check if the extension is reachable. Defaultis OFF.l VoiceMail Select On to activate the voicemail box for the extension or Off todeactivate it.l Ignore Conflict Activate to ignore conflict from other existing numbers.Default is activated.

3.2.5. Extension ManageClick the Extensions menu, and Manage submenu. The Extension Manage table willappear. All the added extensions are listed in this table. You can delete an IP extension byticking the box corresponding to the number and clicking the Delete button on the top leftof the table. Just click on the number to enter the Edit Extension screen if a parameterchange is needed.

www.star-net.cn

- 21 -

3.3. Configure PSTN Lines

3.3.1. Configure Onboard PSTN and GSM lineClick the Lines menu, and Onboard Line submenu. The Onboard Line table will appear.You can edit the parameters of each Line port by selecting Line1 or GSM1.Line1

l Line ID The Line ID is a readonly value. It is generated by the system automaticallyand is used to identify each line in the system.l Line Group Line Group consists of analog or VoIP lines that are associated so thatcalls to any line in the group are rolled over to the next available line in the group when theline is busy. Each onboard line belongs to different Onboard_Line group.

www.star-net.cn

- 22 -

l External Number The PSTN number of the PSTN line connected to the Line port.l Call Direction Only incoming calls are allowed on the line if Incoming is selected;only outgoing calls are allowed on the line if Outgoing is selected; both incoming andoutgoing calls are allowed on the line if Both is selected.l Incoming call route Select an incoming call route from the list. The informationabout the call route will show on the right hand side of the screen.

GSM1

l Line ID The Line ID is a read-only value. It is generated by the system automaticallyand is used to identify each line in the system.l Line Group Line Group consists of analog or VoIP lines that are associated so thatcalls to any line in the group are rolled over to the next available line in the group when theline is busy. Each onboard line belongs to different Onboard_Line group.l External Number The PSTN number of the PSTN line connected to the Line port.l Call Direction Only incoming calls are allowed on the line if Incoming is selected;only outgoing calls are allowed on the line if Outgoing is selected; both incoming andoutgoing calls are allowed on the line if Both is selected.l SMS Callback Select Enable to activate callback function for GSM via SMS.Default is disabled.l SMS Prefix Apply this rule if the SMS starts with the number specified here.l Call Back via Line Select a callback line from the list.l Call out Prefix call out prefix is set to strip the country code. An r represents anumber. (For example, specify rrr to strip all SMS from China (+86))

Click OK to submit the changes, and then click Save & Reload to reload the system totake immediate effect.

www.star-net.cn

- 23 -

3.3.2. Configure lines via VoIP GatewayClick the Lines menu, and Add VoIP Gateway submenu. The Add VoIP Gatewayscreen will appear. You can add a gateway line group and create SIP accounts for theVoIP gateway here.

l Name A description name for memorization. The name will be automatically addedby the system with the prefix gw_ by the system to clearly indicate it is a gateway linegroup.l Number of physical lines Select the number of physical PSTN lines that thegateway supports and that you are using.NOTE:l The total number of the lines is 4, including lines added via VoIP gateway, VoIPprovider and VoIP trunk, excluding the 2 onboard lines. So the available number in the listof the Number of physical lines may change according to how many lines have beenadded and how many lines remain available to be added.

l Outbound Caller ID An optional parameter which fills into the Caller ID field on anoutgoing call.l Keep alive Select ON to allow device to check if the line is reachable. Default isOFF.

Click the Next button. Individual lines will be created and displayed in a columnar format.SIP accounts will be generated for each line with default Line ID, Authen ID and password.Only the password can be modified.

www.star-net.cn

- 24 -

l Line ID The Line ID is the number which the gateway will use to register to theSVX8004G.l Authen ID The authentication ID when registered to the SVX8004G.l Authen Password The authentication password when registered to the SVX8004G.l Call Direction Only incoming calls are allowed on the line if Incoming selected;only outgoing calls are allowed on the line if Outgoing is selected; both incoming andoutgoing calls are allowed on the line if Both is selected.l External Number The PSTN number of the PSTN line connected to the Line port ofthe gateway.

Click the Finish button. The system will bring up the line manage page which shows allthe lines including the 2 onboard lines and the lines added via the gateway.

Click the corresponding line ID to enter the line edit screen. You can modify the propertyof the line as described above.

www.star-net.cn

- 25 -

3.3.3. Configure the VoIP GatewayAfter adding the VoIP gateway line group and creating the SIP accounts for each line, youshould configure the VoIP gateway to register its lines to the SVX8004G system.

Configure the VoIP registrationEach line created for the VoIP gateway in the SVX8004G System has to be configured inthe VoIP gateways SIP or VoIP settings section. Each line has to be configured with aSIP account including Line ID (line number), Authentication ID and AuthenticationPassword. These must match the values you entered in the corresponding fields of thelines you created in the SVX8004G.Configure the RoutingOnce your gateway has been configured and its SIP or VoIP lines are registered withthe SVX8004G System server, the gateway must be configured to forward incoming callsfrom the PSTN to the line numbers (Line ID) of the PSTN lines created in the SVX8004G.Many VoIP gateways can be configured to work with SVX8004G. We recommend thefollowing:l StarNet SVG6000Bl StarNet SVG6116l Grandstream GXW 4104l Dlink DVG 3004Sl Micronet SP 5050l Linksys SPA3000l Tainet Bodhicom 3404/3408

3.3.4. Line StatusClick the Status menu, and Line Status submenu. The Line Status screen will appear.Here you can see whether each line of the gateway is registered or not.

www.star-net.cn

- 26 -

3.4. Configure VoIP lines

3.4.1. Configure VoIP ProviderClick the Lines menu, and Add VoIP Provider submenu. The Add VoIP Provider screenwill appear. You can add a VoIP provider line group and add the SIP accounts acquiredfrom the VoIP provider.

l Name A description name for memorization. The name will be automatically addedby the system with the prefix pv_ by the system to clearly indicate it is a provider linegroup.l Server Address The IP address or Domain name of the providers SIP server.l Server Port The SIP port on which the SIP server is operating. Default is 5060.l Outbound Caller ID An optional parameter which fills into the Caller ID field onoutgoing calls.l Keep alive Select ON to allow device to check if the line is reachable. Default isOFF.l Number of VoIP lines Select the number of VoIP lines supplied by the VoIPprovider and that you are actually using.l Outbound Proxy Address Send outbound signaling to the proxy instead of directlyto the peer. Enter the Outbound proxy IP address.l Outbound Proxy Port Enter the Outbound proxy port number.NOTE:l The total number of the lines is 4, including lines added via VoIP gateway, VoIPprovider and VoIP trunk, excluding the 2 onboard lines. So the available number in the listof the Number of VoIP lines may change according to how many lines have been addedand how many lines remain available to be added.

Click the Next button, Individual lines will be created and displayed in a columnar format.You should fill the SIP accounts information acquired from the provider into the fields of

www.star-net.cn

- 27 -

each line.

l External Number The VoIP number of the line.l Auth ID The authentication ID when registered to the VoIP provider.l Auth Password The authentication password when registered to the VoIP provider.l Direction Only incoming calls are allowed on the line if Incoming is selected; onlyoutgoing calls are allowed on the line if Outgoing is selected; both incoming andoutgoing calls are allowed on the line if Both is selected.l Line ID The Line ID is an internal number used by SVX8004G to identify each line.

Click the Finish button. The system will bring up the line manage page which shows allthe lines including the 2 onboard lines and the lines added via gateway and provider.

Click the corresponding line ID to enter into the line edit screen. You can modify theproperties of the line as described on the previous page.

www.star-net.cn

- 28 -

Click the Status menu, and Line Status submenu. The Line Status screen will appear.Here you can see whether each line of the VoIP provider is registered or not.

3.4.2. Configure VoIP TrunkVoIP Trunk, or SIP Trunk, is a connection between two SIP devices. Unlike theClient-Server relation between SIP client and SIP server, it is a peer-to-peer relationbetween two SIP devices which connects each other via SIP Trunk. An advantage of SIPTrunk is that the two devices can call each other directly at any time as long as their IPaddresses are reachable to each other, with no registration needed between them, and noneed to register to another SIP server in order to be able to call each other.

SVX8004G supports connecting with other SIP devices via SIP Trunk. These SIP devicescan be other SVX80004G or other third party IPPBX, analog gateway, digital gateway,soft switch, etc.

Click the Lines menu, and Add VoIP Trunk submenu. The Add VoIP Trunk screen willappear. You can add trunk line(s) here.

www.star-net.cn

- 29 -

l Name A description name for memorization. The name will be automatically addedwith the prefix tk_ by the system to clearly indicate it is a VoIP trunk.l Trunk Address The IP address of the other SIP device.l Trunk Port The SIP port number of the other SIP device.l Number of physical lines Select the number of VoIP lines which can be talkingsimultaneously in this trunk.NOTE:l The total number of the lines is 4, including the lines added via VoIP gateway, VoIPprovider and VoIP trunk, excluding the 2 onboard lines. So the available number in the listof the Number of VoIP lines may change according to how many lines have been addedand how many lines remain available.

l Inbound Auth ID The inbound authentication ID is used to authenticate incomingcalls from the other SIP device to avoid unauthorized calling. If no value is specified here,no authentication is performed when a call comes in.l Inbound Auth Password The authentication password associated with the inboundauthentication ID.l Outbound Auth ID The outbound authentication ID is used for outgoing calls to getthe authorization by the other SIP device. This valued can be filled or not, depending onwhether the other device requires authentication.l Outbound Auth Password The authentication password associated with theoutbound authentication ID.l Outbound Caller ID When calling from this device to another device, the caller IDwill be replaced with the value specified here. This is an optional parameter. If no value isspecified here, the outgoing caller ID will be the name of the caller extension.l Keep alive Select ON to allow device to check if the line is reachable. Default isOFF.

Click the OK button. The system will bring up the VoIP Trunk manage page which showsall the trunks added. You can edit or delete the trunks here.

www.star-net.cn

- 30 -

3.5. Configure Inbound and Outbound RulesAn Inbound rule defines that where the inbound call should be placed to. This allows youto create a set of rules which specifies how an incoming call should be handled based onthe caller number and the destination number.

An outbound rule defines on which line an outbound call should be placed. This allowsyou to create a set of rules which specifies how a call should be made based on whichextension is making the call and what number it is calling.NOTE:l No outbound call can be made before a valid outbound rule is added.

3.5.1. Configure inbound rulesClick the Rules menu, and Add Inbound Rule submenu. The Add Inbound Rule screenwill appear. You can define an inbound rule here.

www.star-net.cn

- 31 -

l Name Assign a name to identify this outbound rule.l Caller Inspect the caller ID of the incoming call, the call will not be processed by thisinbound rule if the caller ID does not match the value defined here.n Any Any number is acceptable.n Begin with Only numbers begin with the specified value will be accepted.n End with Only numbers end with the specified value will be accepted.n Include with Numbers with the specified value will be accepted.n Specific Only the specified number will be accepted.l Callee Inspect the destination phone number, the call will not be processed by thisinbound rule if the caller ID does not match the value defined here.n Any Any number is acceptable.n Begin with Only numbers begin with the specified value will be accepted.n End with Only numbers end with the specified value will be accepted.n Include with Numbers with the specified value will be accepted.n Specific Only the specified number will be accepted.l Time of the day Select the time periods that this inbound rule will be used.l Incoming call Route Select the destination of the incoming call caught by this rule.n Reject call Reject the incoming call. Caller will hear the busy tone.n Auto attendant Route the call to the auto attendant.n Call though Incoming calls will be routed out via two stage dialing. Caller can bepromoted to do a second dialing, the dial tone will be heard. User can then dial thenumber he wants call.u Pin Caller will be promoted to enter the correct pin code before he can do thesecond dialing if user assigned a value to PIN.

www.star-net.cn

- 32 -

n Call outbound Incoming calls will be routed to a specified outbound number.n Call back via line Device will record the caller ID of the incoming call and then callback to that phone number after caller hangs up then phone. When caller pick up thephone, the dial tone will be heard, and then caller can now dial the phone number he wantcall.u Line Select the line which will be used to call back the caller.u Pin Caller will be promoted to enter the correct pin code before he can do thesecond dialing if user assigned a value to PIN.n Extension Incoming calls will be routed to a selected extension.n Ring group Incoming calls will be routed to a ring group.n Voicemail box of the Extension Incoming calls will be routed to the voicemail boxof the selected extension.


Click the Rule menu then In. Rule Manage submenu. The Inbound Rule Managescreen will appear. You can delete rule(s) by ticking the box corresponding to the rulename and clicking the Delete button on the top left of the table, or clicking the rule nameto enter the Edit Inbound Rule screen if you want to modify the rule.

At the button of the page is the list of all the lines, user can click the line name to quick editthe inbound rules of this line.User can click on the inbound rule name to add it to the inbound rule list of the line whenthe line is open for edit.

3.5.2. Configure inbound rulesClick the Rules menu, and Add Outbound Rule submenu. The Add Outbound Rule

www.star-net.cn

- 33 -

screen will appear. You can define an outbound rule here.

l Name Assign a name to identify this outbound rule.l PIN for Outbound User User will be prompted to enter the pin code when makingoutbound call via this outbound rule.l Dial prefix Apply this rule if the call starts with the number specified here. Forexample, specify 0044 (or 01144 in the US) to specify that all calls to the UK should berouted via a particular line or service provider.l Strip Digit Strip Digit specified that how many digit(s) will be removed from the firstdigit of the number that has been 'caught' by the outbound rule before it is routed to aselected line group.l Prepend User can add prefix to a number that has been 'caught' by the outboundrule before it is routed to a selected line.l Postfix User can add postfix to a number that has been caught by this outbound rulebefore it is routed to a selected line.NOTE:l 'Strip Digit' has higher priority than 'Prepend'. A caught number will be processed by'Strip Digit' first before been processed by 'Prepend', for example, when 'Strip Digit' hasvalue of '2' and 'Prepend' has value of '33', a caught number '123456' will be transformedto '333456' before it is route to a selected line group

l Calls from extension(s) Select the extensions for which this rule applies.l Outbound Route Select the line group on which the calls will be made. Multiple linegroups can be selected and the priority can be adjusted by clicking the up and down arrowicons.n Call blocking Block the outbound call caught by this outbound rule.

Click OK to submit the changes, and then click Save & Reload to reload the system to

www.star-net.cn

- 34 -

take immediate effect.

Click the Rules menu then Out. Rule Manage submenu. The Outbound Rule Managescreen will appear. You can delete rule(s) by ticking the box corresponding to the rulename and clicking the Delete button on the top left of the table, or clicking the rule nameto enter the Edit Outbound Rule screen if you want to modify the rule.

3.5.3. Operation numberClick the Rules menu, and Operation number submenu. The Operation NumberManage screen will appear. You can define the system operation number here.

The PBX operation is:

www.star-net.cn

- 35 -

Disabled User can dial those operation numbers on the analog phone connected on theFXS port of SVX8004G.Enabled User cannot dial those operation numbers on the analog phone connected tothe FXS port of SVX8004G. All operation numbers will be handled by SIP server.

3.5.4. Digit Map RuleClick the Rules menu, and Digitmap Rule submenu. The digit map rule manage screenwill appear. You can modify the digit map rules here.Digit map is used to control the dialing behavior of the phone connected to the FXS port.The number will be send out immediately if the number you dialed matched one of thedigit rules here.

l Pound passthrough Click to enable the FXS port dial # as part of the dialed number.The default is disabled.l Edit the rules Use can edit the rules just like using the notepad. Click OK to save orCancel to abort the changes at the end.l Matching rule: X represent any number between 09. [1359] represent any number in set {1, 3, 5, 6, 7, 8, 9}. . represent any number of digits. T represent dial timeout. * not a wildcard, represent asterisk key only. # not a wildcard, represent hash key only.l Example: 0591. means any number start with 0591. 8XXX means any 4 digits number start with 8. 13[579]. means any number start with 135, 137, 138, 139. X.T means the number will be sent out when dial timeout time reached. *X.# means any number start with * and finish with #. X.# means any number end with #. Be aware here, X.# will send # as part of

www.star-net.cn

- 36 -

the dialed number. 1234567# means all those 8 characters will be send as a number.Use # as send key option in the Other Settings page has lower priority then the digitmaps.

3.6. Advanced Configuration

3.6.1. Ring GroupA ring group allows you to direct calls on a particular number to a group of extensions. Forexample, you could define a group of 3 sales people, and have the general sales numberring on all 3 extensions at the same time or after each other. When you create a ringgroup, you also assign it a virtual extension number. This will be the number used by thephone system to address the ring group.

Click the Advanced menu, and Ring group submenu. The Ring Group Manage pagewill appear.

Manage Ring Group User can delete ring group(s) by ticking the box corresponding tothe number and clicking the Delete button on the top left of the table.

Click Add Ring Group. The Add Ring Group screen will appear:

www.star-net.cn

- 37 -

l Number Assign a 4 digit number to this ring group. The ring group can be called bythis number from any extension or auto attendant.l Name A description name for memorization.l Ring Strategy Select the appropriate ring strategy for this ring group:n Ring all all the extensions in the group will ring at the same time when calls come in.n Hunt The first extension will ring, then the second, then the third etc.l Ring Timeout Specify how long the ring should ring for.l Ring group members Specify the extensions that belong to this ring group. Movethe extensions up or down to adjust the priority.l No Answer Route How to handle the call when no one in the group answers it.


3.6.2. Voice MenuThe auto attendant feature allows SVX8004G to answer incoming calls automatically andpresent the caller with a list of options. The caller can then choose the appropriate optionusing the numbers on his phone key-pad or enter the extension number directly to beconnected to an extension.

You can implement a menu: for example, for sales, press 1; for support, press 2, etc.

Recording a menu promptBefore you create your auto attendant, you must write down the menu options you wish tooffer the caller, think of a suitable text and record the announcement. A simple examplewould be Welcome to Company XYZ; for sales, press 1; for support, press 2; to reach areceptionist, press 0; if you know your partys extension number, you may enter it now.

www.star-net.cn

- 38 -

NOTE:l We recommend you put the number the user should press after the option, i.e. forsales, press 1, rather than press 1 for sales. This is because the user will wait for thedesired option and only then register what number to press.

Once you have devised the text you can record the prompt using any voice recordsoftware and save the voice file in .wav format and then upload it to the device via VoicePrompt page.

Click the Advanced menu, and Voice Menu submenu. The Voice Menu Manage pagewill appear.

Manage Voice Menu User can delete Voice Menu(s) by ticking the box correspondingto the number and clicking the Delete button on the top left of the table. Notice that thereis a default voice menu called Auto_Attendant. User cannot delete this voice menu.

Click Add Voice Menu. The Add voice Menu screen will appear:

www.star-net.cn

- 39 -

l Name A description name for memorize.l Voice Menu No. (5 digits) This is the number for the auto attendant which can becalled from any extension. The length of this number is fixed to 5 digits.l Voice Prompt Select a voice file which will be used by this voice menu from the dragdown list.l No Action Timeout Set the Timeout time for this voice menu.l Salutatory Select a voice file which will be used by this salutatory from the dragdown list.l Action Here you can specify the menu options.n No Action No action will be taken. The system will send an error message to theuser and ask for another input.n Repeat prompt Replay the voice prompt.n Connect to Extension System will transfer the call to the specified extension.n Connect to Outbound System will transfer the call to the specified outboundnumber.n Connect to Ring Group System will transfer the call to the specified ring group.n Connect to Call Queue System will transfer the call to the cal queue.n Connect to Voice Menu System will transfer the call to another voice menu.


www.star-net.cn

- 40 -

3.6.3. Voice PromptClick the Advanced menu, and Voice prompt submenu. The Voice prompt Managepage will appear.

3.6.4. Custom PromptClick the Advanced menu, and Custom Prompt submenu. The Custom PromptManage page will appear.

www.star-net.cn

- 41 -

3.6.5. Call QueueCall Queue holds incoming calls when all members are busy assisting other callers. Callswait in the call queue for the next available member. While calls are waiting, they will hearthe music-on-hold. Calls are distributed out of the call queue on a first in, first out basis, asmembers become available.

Usually Call Queue is used for attendants who need to handle many incoming calls.

SVX8004G supports only one call queue for attendants and up to 6 calls can be waiting inthe queue at the same time.

Click the Advanced menu, and Call Queue submenu. The Attendant Call QueueSettings page will appear. The user can modify the call queue settings here.

www.star-net.cn

- 42 -

l Attendant Call Queue members Specify the extensions that should be part of thiscall queue. Move the extensions up or down to adjust the priority.


3.6.6. Call PickupYou can accept an incoming call that is ringing at another extension which belongs to thesame pickup group as your extension (For how to use call pickup, please refer to thesection Using the telephone.)

Click the Advanced menu, and Call Pickup submenu. The Pickup group Managepage will appear.

www.star-net.cn

- 43 -

Click Add Pickup Group, The Add Pickup Group screen will appear.

l Pickup Group No Select a number for this pickup group. Up to 4 pickup groups canbe added.l Name A description name for memorization.l Pickup Group Members Select the extensions that should be members of thispickup group.


Please refer to the section Using the telephone for guide on how to use call pickup.

www.star-net.cn

- 44 -

3.6.7. Time of DayClick the Advance menu, and Time of Day submenu. The Time of Day Settings pagewill appear.

User can setup the office time in this page so, the inbound call route can be controlled bydifferent time factor.

3.6.8. Call BackClick the Advance menu, and Cal Back submenu. The Call Back setting page willappear.

Caller ID This caller ID is the number that will be sent and showed to the remote user.Display Name The alternative caller ID.

www.star-net.cn

- 45 -

Wait Time System will wait for amount of time before it start call back to caller when itcaught the caller ID of the incoming call.Dial Time Defines for how long the system will ring the remote user before it consider asno answer and hangs up the call.Max Retries Defines the times that the system will try to call back to remote user if theremote user not answering the call.Retry Interval Defines the waiting period between two retries.

Click OK to submit the changes, and then click Save & Reload to reload the

system to take immediate effect.

3.6.9. Call ParkClick the Advance menu, and Cal Park submenu. The Call Park setting page willappear.

Park Number start Defines the start park number used by the call park functionPark Site Count Defines the maximum number of calls that call be parked by thesystem.Parked Time Defines how long the system will park the incoming call.


3.7. General Configuration

3.7.1. Protocol SettingsClick the General menu, and Protocol Settings submenu. The Protocol Setting pagewill appear.

www.star-net.cn

- 46 -

l SIP Port Specify the SIP port on which the SVX8004G is operating. Default is 5060.l Keep Alive period Defines how often will the system send out the keep alivepackage.l RTP Start Specify the start port for RTP protocol. Default is 10000.l RTP End Specify the end port for RTP protocol. Default is 11000.l Line Registry Expires Specify the expiration time for the line registration. Default is360 seconds.l External Addr. (If behind NAT) Specify the external public IP address or domainaddress if the SVX8004G is behind NAT.l Ext. Registry Expires (604800s) Specify the extension registry expiration time.n When this parameter has a value, all extensions will be forced to use this value astheir registry expire time.n When this parameter does not have a value and, the registry expire value of theregistered extension is in the range of 604800 second. The extension can keep their ownregistry expire value.n When this parameter does not have a value and, the registry expire value of theregistered extension is out of the range of 604800 second. SVX8004G will force theextension to use 60 as their expire value.l Domain Refresh (When using external domain) Specify the period for the domainrefresh. The SVX8004G needs know the actual external IP address of the domain name ifdomain name is used in the External Addr. section, so, the device will periodically sentthe refresh command to get the actual external IP address.l DTMF Mode Select the method used to send the DTMF signal. Three methods aresupported: Inband, RFC2833 and SIP INFO. Default is RFC2833.


3.7.2. CDR SettingsClick the General menu, and CDR Settings submenu. The CDR Settings page will

www.star-net.cn

- 47 -

appear.

MAX Size Defines the maximum size of the CDR that system can keep.Delete Size Defines how many records will be deleted when the CDR is full.


Check the Call Detail RecordClick the Status menu, and Call Detail Record submenu. The Call Detail Record pagewill appear.

www.star-net.cn

- 48 -

3.7.3. Ring SettingsClick the General menu, and Ring Settings submenu. The Ring Settings page willappear.

l Ring Timeout (3090s): Define the ringing timeout time, for how long the phone willring until it send a no answer signal back to SIP server and stop ringing.l Ring Timeout for Call Forward (1575s): Define the ringing timeout time when callforward is activated, for how long the phone will ring until it forward calls and stop ringing.

3.7.4. Fax SettingsClick the General menu, and Fax Settings submenu. The Fax Settings page willappear.

Fax function is still under testing, no support will be provided upon this function unless thisfunction is officially released.

www.star-net.cn

- 49 -

3.7.5. Voicemail SettingSVX8004G has 16M bytes flash memory space and can store up to 3 hours voicemailmessages in G.729. By default 14 voicemail box accounts are created and the space foreach extension is about 12 minutes. You can decrease the number of the accounts if notall the extensions need to be voicemail box enabled, so that each account can get morememory space.

Click the General menu, and Voicemail Settings submenu. The Voicemail Settingpage will appear.

l Voicemail Account Specify how many voicemail accounts should be created.l Voice Record Length Specify the record length for each voice mail messagel Msgs Per Mailbox This is a read only parameter. It shows how many messages canbe saved in each voicemail box. Its value changes according to the above twoparameters.l SMTP Server Assign a simple mail transfer protocol server, used to send voice mailnotification.l SMTP Username The username for SMTP server.l SMT Password Password associated with username.

Click OK to submit the changes, and then click Save & Reload to reload the system totake immediate effect.WARNING!l All voicemail messages will be lost if the parameters here are changed, as the systemmust reformat the flash memory zone for storing voicemail messages.l The voicemail option of all the extensions will be set to Off if the parameters here arechanged.

3.7.6. DSP SettingsClick the General menu, and DSP Settings submenu. The DSP Setting page willappear.

www.star-net.cn

- 50 -

l Ext Dial Interval Specify how many seconds to wait for the next digit to be dialed onthe onboard Ext port. If no more digits are dialed before the time expires, then the dialingwill be regarded as completed and the calling will start.l Send Caller ID Specify whether send caller ID information to the telephoneconnected on the onboard Ext port.l Ext Gen. Polarity Reversal Here, user can choose to let extension port generatethe polarity reversal signal or not. Polarity reversal is used for call fares counting purpose.During a calling operation, a polarity reversal signal will be generated to reverse thepolarity of extension lines phone cord when callee pickup the phone in order to notify thecounting device that the call is started. Same when callee hangs up the phone.n Disabled No polarity reversal signal will be generated.n When incoming When extension port received an incoming call, either via line portor via VoIP, polarity reversal signal will be generated when remote phone is picked up orhung up.n When outgoing When extension port making an outgoing call, either via line port orvia VoIP, polarity reversal signal will be generated when remote phone is picked up orhung up.n Always Enable Polarity reversal signal will be generated whenever extension portmaking an outgoing call or receiving an incoming call.l Line Detect Polarity Reversal Set the option enable to enable line port to detect thepolarity reversal signal.l Line Detect Dialtone Select enable-to-enable system detect the dial tone on the line.Please leave this option to enable unless you encountered dial tone detection problem.l Tone Standard Select the country name from the drug down list to set the tone tocorresponding national standard. This parameter only takes effect after rebooting.

Click OK to submit the changes, and then click save & reload to reload the system to

take immediate effect.

www.star-net.cn

- 51 -

3.7.7. Codec SettingClick the General menu, and Codec Setting submenu. The Codec Settings page willappear.

User can modify preference of the codec here. Alaw and Ulaw provide best quality butrequire highest bandwidth. Voice quality of g.729 is worse than Alaw/Ulaw but require lessbandwidth.

3.7.8. System RestoreClick the General menu, and ROXos Restore submenu. The ROXos Restore pagewill appear.

l Create restore data Click this button and a system data restoration file will begenerated.l Download restore date The Create restore date button will become Downloadrestore date button. Click the button to download the restore file.l Restore ROXos to Click Browse to select the rrp backup file you saved beforethen click Restore ROXos to. The system will restore data from the file.

www.star-net.cn

- 52 -

l Restore to default Click this button and all the data will be restored to the factorydefault.

4. Configuration Wizard

SVX8004G provides a wizard function to help user configure the device and setup a basicusable system.

Click the Wizard menu, and Wizard Begin submenu. The wizard will be started.

After wizard started, a small wizard window will appear at the top right corner of the page.The wizard windows provided the basic setup guide step by step. User can click the rightor left arrow icon located at the top right corner of the wizard window to move forward orback.

The web interface will jump to corresponding pages automatically according to the wizard.User can then click the house icon at the top right corner of the wizard window to return tothe main web interface to configure the page.

5. Sending / Receiving Text Message

SVX8004G supports text message sending by SMTP/POP3. The configuration of emailsoftware should be as follows:

a) The incoming mail Server should be filled in the IP address of SVX8004G.b) The outgoing mail Server should be filled in the IP address of SVX8004G.c) The content of the email should only be text format.d) For now, the encoding of the email should only be Unicode (UTF-8).

www.star-net.cn

- 53 -

e) The name of message receiver should be filled in country code followed withmobile phone number @*. (* delegates a symbol or symbols)

www.star-net.cn

- 54 -

www.star-net.cn

- 55 -

6. Using the telephone

6.1. Making calls

6.1.1. Making internal callsInternal calls can be made between any extensions including onboard extensions and IPextensions once they have successfully registered to SVX8004G.

l Pick up your extensions handset.l Listen for the dial tone.l Dial the number of the extension or the number of the ring group followed by #

6.1.2. Making outgoing PSTN calls via onboard lineWhen the SVX8004G system is up, the default Onboard_Line group is ready foroutgoing calls via onboard lines. Before making any outgoing calls via the Onboard_Linegroup, you must add an outbound rule to specify what number the extensions should dial.(To learn to add an outbound rule, please refer to the section Configure OutboundRules.)

l Pick up your extensions handset,l Listen for the dial tone,l Dial the outbound prefix of the calling rule,l Dial the PSTN number followed by #.

6.1.3. Making outgoing PSTN calls via VoIP gatewayMake sure the VoIP gateway has been added and the lines have been successfullyregistered to the SVX8004G. Then make sure an outbound rule has been added for thisVoIP gateway line group. (Please refer to the section Configure lines via VoIP Gatewayfor how to add VoIP gateway and check the registration status. Please refer to the sectionConfigure Outbound Rules for how to add outbound rules.)

l Pick up your extensions handset,l Listen for the dial tone,l Dial the outbound prefix of the calling rule,l Dial the PSTN number followed by #.

6.1.4. Making outgoing VoIP calls via VoIP providerMake sure the VoIP provider has been added and SVX8004G has been successfully

www.star-net.cn

- 56 -

registered to the VoIP provider with the lines. And then make sure an outbound rule hasbeen added for this VoIP provider line group. (Please refer to the section Configure VoIPProvider for how to add VoIP provider and check the registration status. Please refer tothe section Configure Outbound Rules for how to add outbound rules.)

l Pick up your extensions handset.l Listen to the dial tone.l Dial the outbound prefix of the VoIP provider line group.l Dial the number followed by #.

6.1.5. Making outgoing VoIP calls via VoIP TrunkMake sure the VoIP trunk has been added and an outbound rule has been added for thisVoIP trunk line group. (Please refer to the section Configure VoIP Trunk for how to addVoIP trunk. Please refer to the section Configure Outbound Rules for how to addoutbound rules.)

l Pick up your extensions handset.l Listen to the dial tone.l Dial the outbound prefix of the VoIP trunk line group.l Dial the number followed by #.

6.2. Receiving callsWhen receiving calls, either from PSTN or VoIP, your phone will ring. Just lift the handsetto accept the call.

6.2.1. Call PickupYou can accept an incoming call that is ringing at another extension which belongs to thesame pickup group as your extension. (Please refer to the subsection Call Pickup underthe Advanced Configuration section for how to add Call Pickup.)

l Pick up your extensions handset.l Listen to the dial tone.l Dial *5X follow by #, where X represents the ringing extension number.

6.2.2. Call WaitingA prompt tone will be heard indicating a new call is coming while you are talking. You canpress the HOLD key to switch to the new call. After that you can press the HOLD keyagain to switch between the two calls.

The call waiting function requires support at both the server side and the phone side. Ifyour IP phone supports call waiting, you can activate it at the server side as follows:

www.star-net.cn

- 57 -

l Pick up your IP phones handset.l Listen to the dial tone.

Dial *970 followed by #. A voice prompt can be heard confirming the successfulactivation of the call waiting function.

To deactivate the call waiting function:l Pick up your IP phones handset.l Listen to the dial tone.l Dial *971 follow by #. A voice prompt can be heard confirming you the successfuldeactivation of the call waiting function.

You can check the call waiting status of the extensions on the Extension Status screen.The column C.W. shows whether the call waiting function is enabled or not. A tip willshow up when you put your mouse over the icon.

6.2.3. Call TransferringYou can transfer an incoming call to another number during conversation.l During conversation, dial #. A voice prompt can be heard telling you to dial thenumber you want to transfer to.l Dial the number you want to transfer to.l When the number starts to ring, your extension will get a busy tone. Just hang up tofinish transferring the call.NOTE:l The transferring number can be any number that the extension can call.

6.2.4. Call ForwardingThree kinds of call forwarding are supported in SVX8004G:l Call Forwarding Busy Incoming calls will be automatically forwarded to anothernumber when your extension is busy.

www.star-net.cn

- 58 -

To activate call forwarding busy:n Pick up your IP phones handset.n Listen to the dial tone.n Dial *974X follow by #, where X represents the number you want the call to beforwarded to. A voice prompt can be heard telling you the successful activation of the callforwarding busy function.

To deactivate call forwarding busy:n Pick up your IP phones handset.n Listen to the dial tone.l Dial *975 followed by #. A voice prompt can be heard telling you the successful

deactivation of the call forwarding busy function.l Call Forwarding No Answer Incoming calls will be automatically forwarded to anothernumber when no one answers after 25 seconds.

To activate call forwarding no answer:n Pick up your IP phones handset.n Listen to the dial tone.n Dial *976X followed by #, where X represents the number you want the call to beforwarded to. A voice prompt can be heard telling you the successful activation of the callforwarding no answer function.

To deactivate call forwarding no answer:n Pick up your IP phones handset.n Listen to the dial tone.n Dial *977 follow by #. A voice prompt can be heard telling you the successfuldeactivation of the call forwarding no answer function.

l Call Forwarding All Calls All Incoming calls will be automatically forwarded toanother number unconditionally.

To activate call forwarding all calls:n Pick up your IP phones handset.n Listen to the dial tone.n Dial *972X followed by #, where X represents the number you want the call to beforwarded to. A voice prompt can be heard telling you the successful activation of the callforwarding all calls function.

To deactivate call forwarding all calls:n Pick up your IP phones handset.n Listen to the dial tone.n Dial *973 followed by #. A voice prompt can be heard telling you the successfuldeactivation of the call forwarding all calls function.

www.star-net.cn

- 59 -

NOTE:l The forwarding number can be any number that the extension can call.You can check the call forwarding status of the extensions on the Extension Statusscreen. The column Fwd. shows whether the call forwarding function is activated ordeactivated. A tip will show up with detail forwarding information when you put yourmouse

6.2.5. Call ParkUser can park an incoming call and pick it up at other destination.l During the conversation, press # key,l Waiting for the prompt tone, and then dial 700 followed by # key.l System will prompt a number such as 701.l Hang up the phone.l You can now pick up any other phone, dial the prompted number,l The Parked call will be picked up in the new destination.

6.3. Using VoicemailIf voicemail is enabled on an extension, incoming calls will be forwarded to voicemail if theextension is busy or no one answers after 45 seconds. The caller will hear the voiceprompt telling him or her to leave a message.

You can check your voicemail box and record your personal mailbox greeting by dialing*888 on your extension and following the voice instructions. For onboard analogextension, the password of the mailbox is the same as the extension number. For IPextension, the password of the mailbox is the same as the extensions password.NOTE:

l If call forwarding on busy or call forwarding no answer is activated, the call will not beforwarded to voicemail.l The SVX8004G will play a voice prompt to users when the mailbox for the extension isgoing to be full.

www.star-net.cn

- 60 -

6.4. Function key listThe following table lists all the numbers, functions and commands you can enter on theextension while it is idle.Keys Function performed*100 Enter administrators IVR (voice menu), Following the voice

instructions, you can get the system IP address and changethe login password of this IVR.

*888 Enter voicemail box IVR (voice menu). Following the voiceinstructions, you can manage your extensions voicemail boxand record your personal mailbox greeting.

*968 Activate call-waiting function for the extension.*969 Deactivate call-waiting function for the extension*972X Activate call forwarding all calls function for the extension,

where X represents the number you want the call to beforwarded to.

*973 Deactivate call forwarding all calls function for the extension.*974X Activate call forwarding busy function for the extension, where

X represents the number you want the call to be forwarded to.*975 Deactivate call forwarding busy function.*970X Activate call forwarding no answer function for the extension,


*971 Deactivate call forwarding no answer function.*976X Activate call forwarding off line function for the extension,


*977 Deactivate call forwarding off line function.77777 The number of the auto attendant. You can call this number on

any extension to enter auto attendant.*5 Pickup the incoming call that ringing at a random extension

which belongs to the same pickup group as your extension.*6X Pick up the incoming call that is ringing at another extension

which belongs to the same pickup group as your extension,where X represents the number of extension you want pickup.

#*700 Park an incoming call in the system. System will then prompt apickup number. User can enter this pickup number at anyextension in the system to pickup the call.

*101 Enter the IVR of call forwarding services settings. User canactivate or deactivate all call forwarding services here.

# Transfer an incoming call to another number duringconversation.

*978 Activate Do Not Disturb function.*979 Deactivate Do Not Disturb function.

1. Introduction1.1. Overview1.2. Capacity1.3. Features1.4. Software Specifications1.5. Hardware Specifications

2. Installation2.1. Safety Precautions2.2. Check Package Contents2.3. Ensure You Have the Following2.4. Front Panel2.5. Back Panel2.6. Connect the Device2.6.1. Connect diagram2.6.2. Connect the power2.6.3. System Startup2.6.4. Connect the network2.6.5. Connect the computer2.6.6. Connect the telephone2.6.7. Connect the PSTN line

3. Configuration3.1. Initial Configuration3.1.1. Get the device IP address3.1.2. Login into the Web interface3.1.3. Web interface overview3.1.4. Network Settings3.1.5. Control Panel3.1.6. Application Manage3.1.7. IP-PBX Configuration Interface

3.2. Configure Extensions3.2.1. Configure Onboard Extensions3.2.2. Configure IP Extensions3.2.3. Extension Status3.2.4. Add IP Extension Group3.2.5. Extension Manage

3.3. Configure PSTN Lines3.3.1. Configure Onboard PSTN and GSM line3.3.2. Configure lines via VoIP Gateway3.3.3. Configure the VoIP Gateway3.3.4. Line Status

3.4. Configure VoIP lines3.4.1. Configure VoIP Provider3.4.2. Configure VoIP Trunk

3.5. Configure Inbound and Outbound Rules3.5.1. Configure inbound rules3.5.2. Configure inbound rules3.5.3. Operation number3.5.4. Digit Map Rule

3.6. Advanced Configuration3.6.1. Ring Group3.6.2. Voice Menu3.6.3. Voice Prompt3.6.4. Custom Prompt3.6.5. Call Queue3.6.6. Call Pickup3.6.7. Time of Day3.6.8. Call Back3.6.9. Call Park

3.7. General Configuration3.7.1. Protocol Settings3.7.2. CDR Settings3.7.3. Ring Settings3.7.4. Fax Settings3.7.5. Voicemail Setting3.7.6. DSP Settings3.7.7. Codec Setting3.7.8. System Restore

4. Configuration Wizard5. Sending / Receiving Text Message6. Using the telephone6.1. Making calls6.1.1. Making internal calls6.1.2. Making outgoing PSTN calls via onboard line6.1.3. Making outgoing PSTN calls via VoIP gateway6.1.4. Making outgoing VoIP calls via VoIP provider6.1.5. Making outgoing VoIP calls via VoIP Trunk

6.2. Receiving calls6.2.1. Call Pickup6.2.2. Call Waiting6.2.3. Call Transferring6.2.4. Call Forwarding6.2.5. Call Park

6.3. Using Voicemail6.4. Function key list

Documents

SVX8004G IP-PBX User Guide_20080611.pdf