Models

DXM100 Models

B1 =

RadioConfiguration

B1Base

DXM100- R1

Modbus controller for data aggregation of sensorsand wireless networksPower: 12−30 V dc/ Solar/ BatteryComms: RS-485, CAN, RS-232 w/flow or secondary RS-485 Inputs: (4) universal INOutputs: (4) NMOS OUT, (2) analog OUT (0–10 V or 4–20 mA)Power Out: (2) Selected 5 V or 16 V switched power, (1) 5 V courtesy power

Blank = NoneR1 = 900 MHz, 1 W PE5 Performance Radio (North America)R2 = 900 MHz, 1 W HE5 MultiHop Data Radio (North America)R3 = 2.4 GHz, 65 mW PE5 Performance Radio (Worldwide)R4 = 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)R5 = 900 MHz, 65 mW HE5L MultiHop Data Radio (Used for M-GAGE networks)R8 = 900 MHz, Performance Radios approved for Australia/New ZealandR9 = 900 MHz, MultiHop Radio approved for Australia/New Zealand

B2 = Smart valve control, SDI-12 data collectionPower: 12−30 V dc/Solar/BatteryComms: RS-485, (1) SDI-12 sensor interfaceInputs: (4) universal INOutputs: (4) NMOS OUT, (2) 0-10 V analog, (2) DC LatchingPower Out: (2) Adjustable 5 V to 24 V switched power, (1) SDI switched power, and (1) 5 V courtesy power

S1 = Modbus slave I/O device for MultiHop wireless networks or wired networksPower: 12−30 V dc/Solar/BatteryComms: RS-485Inputs: (4) Universal INOutputs: (4) NMOS OUT, (2) Analog OUT (0–10 V or 4–20 mA)Power Out: (2) Selectable 5 V or 16 V switched power, (1) 5 V courtesy power

S2 = Modbus slave device for valve control, SDI-12 data collection for MultiHop wireless networks or wired networks Power: 12−30 V dc/Solar/BatteryComms: RS-485, (1) SDI-12 sensor interfaceInputs: (4) universal INOutputs: (4) NMOS OUT, (2) 0–10 V analog, (2) DC Latching Power Out: (2) Adjustable 5 V to 24 V switched power, (1) SDI switched power, and (1) 5 V courtesy power

For S1 and S2 models, only order the R2, R4, R5, and R9 radio configurations.

Cellular CommunicationControllers accept Banner GSM and LTE modems only. Cellular modems are ordered separately as accessories under thefollowing part numbers:

• GSM/3G (HSPA) – SXI-GSM-001• LTE – Verizon – SXI-LTE-001

Sure Cross® Wireless Models Key

Original Document204686 Rev. C

25 July 2019

204686

DXM150 Models

B1 =

RadioConfiguration

B1Base

DXM150- R1

Blank = NoneR1 = 900 MHz, 1 W PE5 Performance Radio (North America)R2 = 900 MHz, 1W HE5 MultiHop Data Radio (North America)R3 = 2.4 GHz, 65 mW PE5 Performance Radio (Worldwide)R4 = 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)R5 = 900 MHz, 65 mW HE5L MultiHop Data Radio (Used for M-GAGE networks)R8 = 900 MHz, Performance Radios approved for Australia/New ZealandR9 = 900 MHz, MultiHop Radio approved for Australia/New Zealand

Modbus controller designed for applications with high I/O count, isolated inputs or integrated relaysPower: 12−30 V dc/Solar/Battery Comms: RS-485 and RS-232 / CAN or secondary RS-485 Inputs: (2) Isolated discrete, (8) UniversalOutputs: (2) Relay, (4) NMOS, (2) AnalogPower Out: (2) Jumper selectable between 2.7 V or battery,4.2 V or incoming power

B2 = Modbus controller for high I/O count applications Power: 12-30 V dc/Solar/BatteryComms: RS-485 and RS-232 w/flow control or secondary RS-485 Inputs: (2) Isolated discrete, (8) UniversalOutputs: (8) PNP/NPN Selectable, (2) AnalogPower Out: (2) Courtesy power out; (2) jumper selectablebetween 2.7 V or battery, 4.2 V or incoming power

S1 = Modbus slave with high I/O count for MultiHop wireless networks or wired networks Power: 12–30 V dc/Solar/BatteryComms: RS-485Inputs: (2) Isolated discrete, 8 UniversalOutputs: (2) Relay, (4) NMOS Discrete, (2) AnalogPower Out: (2) Jumper selectable between 2.7 Vor battery, 4.2 V or incoming power

S2 = Modbus slave with high I/O count for MultiHop wireless networks or wired networks Power: 12–30 V dc/Solar/BatteryComms: RS-485Inputs: (2) Isolated discrete, (8) UniversalOutputs: (8) PNP/NPN Selectable, (2) AnalogPower Out: (2) Courtesy power out; (2) Jumper selectablebetween 2.7 V or battery, 4.2 V or incoming power

For S1 and S2 models, only order the R2, R4, R5, and R9 radio configurations.

Cellular CommunicationControllers accept Banner GSM and LTE modems only. Cellular modems are ordered separately as accessories under thefollowing part numbers:

• GSM/3G (HSPA) – SXI-GSM-001• LTE – Verizon – SXI-LTE-001

Sure Cross® Wireless Models Key

2 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 204686 Rev. C

DXM700 Models

B1 =

Radio Configuration

B1Base

DXM700- R1

Modbus controller for data aggregation ofsensors and wireless networksPower: 12−30 V dcComms: RS-485, Secondary RS-485 Outputs: Four PNP

Blank = NoneR1 = 900 MHz, 1 W PE5 Performance Radio (North America)R2 = 900 MHz, 1 W HE5 MultiHop Data Radio (North America)R3 = 2.4 GHz, 65 mW PE5 Performance Radio (Worldwide)R4 = 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)R5 = 900 MHz, 65 mW HE5L MultiHop Data Radio (Used for M-GAGE networks)

Cellular CommunicationControllers accept Banner GSM and LTE modems only. Cellular modems are ordered separately as accessories under thefollowing part numbers:

• GSM/3G (HSPA) – SXI-GSM-001• LTE – Verizon – SXI-LTE-001

Sure Cross® Wireless Models Key

P/N 204686 Rev. C www.bannerengineering.com - Tel: + 1 888 373 6767 3

DXM1000 Models

B1 =

RadioConfiguration

B1Base

DXM1000- R1

Modbus controller for data aggregation of sensorsand wireless networksPower: 12−30 V dc/ Solar/ BatteryComms: RS-485, CAN, RS-232 w/flow or secondary RS-485 Inputs: (4) universal INOutputs: (4) NMOS OUT, (2) analog OUT (0–10 V or 4–20 mA)Power Out: (2) Selected 5 V or 16 V switched power, (1) 5 V courtesy power

Blank = NoneR1 = 900 MHz, 1 W PE5 Performance Radio (North America)R2 = 900 MHz, 1 W HE5 MultiHop Data Radio (North America)R3 = 2.4 GHz, 65 mW PE5 Performance Radio (Worldwide)R4 = 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)R5 = 900 MHz, 65 mW HE5L MultiHop Data Radio (Used for M-GAGE networks)R8 = 900 MHz, Performance Radios approved for Australia/New ZealandR9 = 900 MHz, MultiHop Radio approved for Australia/New Zealand

B2 = Smart valve control, SDI-12 data collectionPower: 12−30 V dc/Solar/BatteryComms: RS-485, (1) SDI-12 sensor interfaceInputs: (4) universal INOutputs: (4) NMOS OUT, (2) 0-10 V analog, (2) DC LatchingPower Out: (2) Adjustable 5 V to 24 V switched power, (1) SDI switched power, and (1) 5 V courtesy power

Cellular CommunicationControllers accept Banner GSM and LTE modems only. Cellular modems are ordered separately as accessories under thefollowing part numbers:

• GSM/3G (HSPA) – SXI-GSM-001• LTE – Verizon – SXI-LTE-001

Sure Cross® Wireless Models Key

4 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 204686 Rev. C

DXM1500 Models

B1 =

RadioConfiguration

B1Base

DXM1500- R1

Modbus controller for data aggregation of sensorsand wireless networksPower: 12−30 V dc / Solar / BatteryComms: RS-485 master/slaveInputs: (4) universal, (2) isolatedOutputs: (4) NMOS, (2) analog (0–10 V or 4–20 mA), (2) relay(1) 5 V courtesy power

Blank = NoneR1 = 900 MHz, 1 W PE5 Performance Radio (North America)R2 = 900 MHz, 1 W HE5 MultiHop Data Radio (North America)R3 = 2.4 GHz, 65 mW PE5 Performance Radio (Worldwide)R4 = 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)R5 = 900 MHz, 65 mW HE5L MultiHop Data Radio (Used for M-GAGE networks)R8 = 900 MHz, Performance Radios approved for Australia/New ZealandR9 = 900 MHz, MultiHop Radio approved for Australia/New Zealand B2 = Modbus controller for high I/O count applications

Power: 12-30 V dc/Solar/BatteryComms: RS-485 and RS-232 w/flow control or secondary RS-485 Inputs: (2) Isolated discrete, (8) UniversalOutputs: (8) PNP/NPN Selectable, (2) AnalogPower Out: (2) Courtesy power out; (2) jumper selectablebetween 2.7 V or battery, 4.2 V or incoming power

Cellular CommunicationControllers accept Banner GSM and LTE modems only. Cellular modems are ordered separately as accessories under thefollowing part numbers:

• GSM/3G (HSPA) – SXI-GSM-001• LTE – Verizon – SXI-LTE-001

Sure Cross® Wireless Models Key

P/N 204686 Rev. C www.bannerengineering.com - Tel: + 1 888 373 6767 5

Wireless Q45 Sensor NodesPhotoelectric Models

DX80NRadio

Q45Device Type Input Options Special 1

2 – 2.4 GHz9 – 900 MHz

PhotoelectricsCV – Convergent (2.4 GHz only)D – DiffuseE – Emitter (2.4 GHz only)F – Fiber OpticLP – RetroreflectiveR – Receiver (2.4 GHz only)

Other ModelsB – Single ButtonRD – Remote DiscreteU – Universal

Blank – No input2 – Two buttons (push button only)N – Non-contact switch (RD only)

Blank – No optionKR – Korean approvalsL – 10-30 V dc Power (photoelectric only)NB – Shipped with no batteryNH – No 1/2-inch port (available only on inputs 2 and N)AN – Australian approvalsQFP – Flying leadsQD – M12/Euro-style QD (photoelectric only)

Blank – No option2 – Namur input (RD only)DL – Dome indicator (4 Color LED) (Q45B only)L – 4-color LEDQ5 – M12/Euro-style QD (photoelectrics only)

For U models, the sensor must be ordered separately.

E and R Photoelectrics (Emitter and Receiver) are normally specified in pairs

Example Models:• DX80N2Q45LP – 2.4 GHz Q45 with a retroreflective photoelectric sensor• DX80N9Q45RD – 900 MHz Q45 with a remote discrete input• DX80N9Q45TH – 900 MHz Q45 temperature and relative humidity sensor

Vibration and Temperature Models

DX80NRadio

Q45Device Type Options Special 1

2 – 2.4 GHz9 – 900 MHz

VT – Vibration/TemperatureVA – Vibration/Temperature All-in-OneVTP – Vibration/Temperature (pre-configured DIP switches for QM42VT1 sensors) Blank – No option

KR – Korean approvalsNB – Shipped with no batteryAN – Australian approvals

Blank – No option

For the VT and VTP models, the sensor must be ordered separately.

Sure Cross® Wireless Models Key

6 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 204686 Rev. C

DX99 Models

DX99DeviceFamily

G = GatewayN = Node

9 = 900 MHz FHSS2 = 2.4 GHz FHSS

NRadio

9Comms

X

C = CustomX = None

1 = FlexPower, battery2 = FlexPower, no battery3 = FlexPower, 2-pack battery6 = 10 to 30 v dc, no battery

Power2

AntennaS

S = External 0, 1, 2, 4

IN2

Discrete

A = Asynchronous CounterH = 1 Hart and 1 NPNN = NPNP = PNPS = Serial InterfaceX = None

TypeN

0

OUT0

B = BridgeC = Bridge and ThermistorE = Event CounterF = Frequency CounterM = 0 to 20 mAR = RTDT = ThermocoupleV = 0 to 10 V dcX = None

TypeM

Analog

0, 1, 2, 3, 4

IN2

TypeX

X 0

OUT0

A = PolycarbonateD = Single Chamber Metal

HousingD

BoostX

0 = No boost (3.6 V)1 = 10 V2 = 18 V3 = 20 V4 = 13 V5 = 19 V6 = 13 V HART7 = 19 V HART

Blank = StandardX = Special

CustomX

DX99DeviceFamily

DR = Data Radio

9 = 900 MHz FHSS2 = 2.4 GHz FHSS

DRRadio

9Antenna

S

S = External

21 = 1 RTD, 1 Discrete, 2 0−20 mA Analog22 = 1 RTD, 1 Discrete, 2 0−10 V Analog23 = 1 RS-485, 1 Discrete, 2 0−20 mA Analog24 = 1 RS-485, 1 Discrete, 2 0−10 V Analog25 = 1 HART, 1 Discrete, 2 0−20 mA Analog26 = 1 HART, 1 Discrete, 2 0−10 V Analog

Type21

Physical Layer

D = Single Chamber Metal

HousingD

BoostX

0 = No boost (3.6 V)1 = 10 V2 = 18 V3 = 20 V4 = 13 V5 = 19 V6 = 13 V HART7 = 19 V HART

Blank = StandardX = Special

CustomX

M = Serial

CommsM

Blank = Std Internal Battery3 = Two-Pack Battery

H

H = MultiHop

Sure Cross® Wireless Models Key

P/N 204686 Rev. C www.bannerengineering.com - Tel: + 1 888 373 6767 7

Performance Models

DX80Radio Host Comms Power Antenna I/O Housing/Options

2 – 2.4 GHz9 – 900 MHz

Device

G – GatewayN – Node

M – Modbus (Gateway only)X – None

1 – Internal battery2 – FlexPower6 – 10 to 30 V dc7 – 100 to 277 V ac8 – 100 to 230 V ac

S – ExternalW – InternalX – No antenna

P – Serial RS485/RS232P1 – FlexPower, 2 Discrete IN, 2 Discrete OUT, 2 Analog IN, Boost VoltageP2 – 4 Discrete IN, 4 Discrete OUT, 2 Analog IN, 2 Analog OUTP3 – FlexPower, ThermocoupleP4 – FlexPower, RTDP5 – FlexPower, 2 Disc IN, 2 Disc OUT, 4 Analog INP6 – Serial interfaceP7 – FlexPower, 12 NPN Discrete IOP8 – 12 PNP Discrete IOP12 – FlexPower, SDI-12, Bridge, Counter, Disc, AnalogP14 – 1 Configurable Discrete IN, 1 Configurable Analog IN, 1 Thermistor, 1 Async Counter, 1 SPP15 – 2 Selectable Discrete IN, 2 0–10V Analog IN, 2 AC/DC Relay (SPDT), 2 PNP Disc OUT, 2 0–10V Analog OUTP16 – 2 Configurable Disctete IN, 2 Async Counters, 4 NMOS OUTP17 – 2 Selectable discrete, AC supply current and voltage monitoring (Current Transformer), One AC/DC relay (SPDT), one 0 to 10V analog out, one 18V courtesy power out.PM2 – Pre-mapped, 4 Discrete OUT, 2 Analog IN, 2 Analog OUTPM8 – Pre-mapped, 12 Discrete IOPM8L – Pre-mapped, 12 Discrete IO, No LCDPB1 – Board Module, FlexPower, 2 Discrete IN, 2 Discrete OUT, 2 Analog INPB2 – Board Module, 2 Discrete IN, 2 Discrete OUT, 2 Analog IN, 2 Analog OUTDCLATCH – 1 Discrete IN, 1 Event Counter, 1 DC Latching (H-Bridge) OUT

Blank – IP67C – IP20 housing (external wiring access)E – Environmental housingL – No LCD, no rotary dials

Not all model combinations are available.

Models listed with an L (Housing/Option) are basic unitsthat may not include all listed options in the I/O column.

G 9 M 6 S P2Specials

NB – no battery includedKR – Korea approvalsAN – Australia/New Zealand approvals

Sure Cross® Wireless Models Key

8 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 204686 Rev. C

Performance Condition Monitoring Models

DX80Radio Host Comms Power Antenna Device Type Housing/Options

2 – 2.4 GHz9 – 900 MHz

Device

N – Node

X – None 1 – Internal battery2 – FlexPower6 – 10 to 30 V dc7 – 100 to 277 V ac8 – 100 to 230 V ac

S – ExternalW – InternalX – No antenna

CM - Condition Monitoring for multiple concurrent sensing devices (vibration/temp VT1, current transformer, two pressure sensor (0-10 V) inputs, one thermistor input, two discrete inputs, Two AC/DC Relay SPDT (AC model only). All sensors sold separately.

CM1 - Condition Monitoring for Vibration/Temperature (VT1 sensor sold separately) and Current (20A CT and 150A CT included). Node pre-wired for sensors with specific selectable DIP switch configuration

Blank – IP67C – IP20 housing (external wiring access)E – Environmental housingL – No LCD, no rotary dials

Not all model combinations are available.

Models listed with an L (Housing/Option) are basic unitsthat may not include all listed options in the I/O column.

N 9 M 6 S CMSpecials

NB – no battery includedKR – Korea approvalsAN – Australia/New Zealand approvals

Performance Pressure Sensing Models

DX80Radio Host Comms Power Antenna Device Type Option 1

2 – 2.4 GHz9 – 900 MHz

Device

N – Node

X – None 1 – Internal battery2 – FlexPower6 – 10 to 30 V dc7 – 100 to 277 V ac8 – 100 to 230 V ac

S – ExternalW – InternalX – No antenna

PS - Pressure Sensing

Blank – Sensing in housing port1 - Sensor attached via 1 m cable

Not all model combinations are available.

N 9 M 6 S PSSpecial 1

NB – no battery includedKR – Korea approvalsAN – Australia/New Zealand approvals

Range50G

50G - 0 to 50 PSI gauge150G - 0 to 150 PSI gauge500S - 0 to 500 PSI sealed gauge3000S - 0 to 3000 PSI sealed gauge

Sure Cross® Wireless Models Key

P/N 204686 Rev. C www.bannerengineering.com - Tel: + 1 888 373 6767 9

MultiHop Models

DX80ISM Band Host Comms I/O Housing/Options

2 – 2.4 GHz9 – 900 MHz

Device

DR – ModbusER – EthernetSR – Serial M – Modbus

Blank – IP67C – IP20 housing (external wiring access)E – Environmental housing with internal batteryL – No LCD, no rotary dialsD – 10 to 30 V dc power

Not all model combinations are available.

Models listed with an L under Housing/Options are basic modelsthat may not include all I/O options.

DR 9 M H2

H – No I/OH1 – FlexPower, 4 Disc IN, 2 Disc OUT, 4 Analog IN, 1 thermistor IN, 1 Counter INH2 – 4 Disc IN, 4 Disc OUT, 2 Analog IN, 2 Analog OUTH3 – FlexPower, ThermocoupleH4 – FlexPower, RTDH5 – FlexPower, 4 Disc IN, 2 Disc OUT, 4 Analog INH6 – Serial interfaceH7 – FlexPower 12 NPN Discrete I/OH8 – 12 PNP Discrete I/OH12 – FlexPower, SDI-12, Bridge, Counter, Disc, AnalogH14 – 1 Configurable Disc IN, 1 Configurable Analog IN, 1 Thermistor, 1 SDI-12, 1 Async Counter, 1 SPH15 – 2 PNP Disc IN, 2 0–20 mA Analog IN, 2 AC/DC Relay (SPDT), 2 PNP Disc OUT, 2 0–10V Analog OUTH17 – 2 Selectable Disc, AC supply current and voltage monitoring (Current Transformer), One AC/DC relay (SPDT), one 0–10 V analog out, one 18 V courtesy power outHB1 – FlexPower board module, 2 Disc IN, 2 Disc OUT, 2 Analog INHB2 – Board module, 2 Disc IN, 2 Disc OUT, 2 Analog IN, 2 Analog OUTDCLATCH – 2 Disc IN, 2 Event Counters, 1 DC Latching (H-Bridge) OUT

Specials

NB – No battery includedKR – Korean approvalsAN – Australia/New Zealand approvals

AC Power

Blank – Not an ac device7 – 100 to 277 V ac8 – 100 to 230 V ac

900 MHz

DX80...C 900 MHz Model

Sure Cross® Wireless Models Key

10 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 204686 Rev. C

Accessories

DX85 Models

DX85Host Comms I/O Housing

M – ModbusC – Custom software

P2 – 10–30 V dc; 4 Discrete IN, 4 Discrete OUT, 2 Analog IN, 2 Analog OUTP7 – FlexPower, 12 NPN Discrete IOP8 – 10–30 V dc; 12 PNP Discrete IO

Blank – IP67C – IP20 housing with external wiring access

M P2

Battery Supply Modules

DX81

H – For the DX99LITH – Lithium batteriesP6 – 6-pack housing

LITH

Sure Cross® Wireless Models Key

© Banner Engineering Corp. All rights reserved