Embed Size (px)
Citation preview
Support systemsAssembly instruction
2
Support systems | Light-weight designAssembly instruction
6 | Central suspension for wire mesh cable tray of
up to 300 mm width
Connect the central hanger GBAG 20/30 to the dowel
using sleeve VM M8*. Mount the tabs GV 30 as well as
the profile rails together with the wire-mesh cable tray.
5 | Central suspension for wire-mesh cable tray of
up to 100 mm width
Connect the central hanger GBAG 10 to the dowel using
sleeve VM M8*. Mount the couplers GV 30 together with
the wire-mesh cable tray.
4 | Wall mounting with bracket KWW
For mounting use dowels as e.g. SD 8/10*. Use outer
slots of the profile.
3 | Wall mounting with bracket KWF
For mounting use dowels as e.g. SD 10/10*. The thick
washer US 13x30x6 must be mounted as well.
2 | Wall mounting with bracket KSLW
For mounting use dowels as e.g. SD 8/30*. The spacer
KSL-SP must be positioned first.
1 | Wall mounting with bracket KWLL
For mounting use dowels as e.g. SD 8/30* and replace
the small washer US 8x17 with the large flat washer
US 8x25*.
Assembly instruction for support systems of wire-mesh cable trays and cable trays in concrete.
* The article is not included in the scope of delivery and must be ordered separately.
3
Support systems | Light-weight designAssembly instruction
15 | Ceiling mounting with trapezium bow TBS
Fold out the trapezium sheet, then attach the bow using
the bolt and nut SES 8x110, SEM 8. Various
connections are possible, as e.g. by means of threaded
bar M8/10.
14 | Ceiling mounting with head plate BGA 41 and
C-profile KHA 41
For mounting use two dowels as e.g. SD 8/10*. Attach
the C-profile using screw set KLS 10x20*. Fasten the
bracket KA using screw set SES 10x20*, AMF22 M10*.
The optional protection cap SA* is pushed onto the
bracket from the bottom.
13 | Ceiling mounting with ceiling-fixed bracket
KDAG 41
For mounting use two dowels as e.g. SD 8/10*. Attach
the bracket KA 30 using screw set SES 10x20*,
AMF22 M10*. The optional protection cap SA* is
pushed onto the bracket from the bottom.
12 | Ceiling mounting with bracket support KSLW
For mounting use dowels as e.g. SD 8/30*. The spacer
KSL-SP must be positioned first. Mount the bracket KSL
using screw set FRS 8x20, SEMS 8.
11 | Ceiling mounting with head plate BGU 50 and
U-profile KHU 50
For mounting use two dowels as e.g. SD 8/10*. Mount
the U-profile using screw set KLS 10x20*. Secure the
bracket KUL with screw set KLS 10x20. The optional
protection cap SU 50* is pushed onto the bracket from
the bottom.
10 | Ceiling mounting with bracket support KDU 50
For mounting use two dowels as e.g. SD 8/10*. Secure
the bracket KUL using screw set KLS 10x20. The
optional protection cap SU 50* is pushed onto the
bracket from the bottom.
9 | Ceiling mounting with ceiling-fixed bracket DB
For mounting use dowels as e.g. SD 8/30* and replace
the small washer US 8x17 with the large flat washer
US 8x25*.
8 | Central suspension for cable trays of up to
300 mm width
Insert the central hanger MA into the cable tray in a tilted
position and clamp by turning. Insert the assembled
threaded rod GB M10* sideways into the central hanger
MA and secure using nut SEM 10*.
7 | Central suspension for cable trays of up to
300 mm width
Connect the central hanger GBAR to the dowel using
sleeve VM M10*. Dismantle the profile rails and
reassemble together with the cable trays.
* The article is not included in the scope of delivery and must be ordered separately.
4
Support systems | Light-weight designAssembly instruction
16 | Ceiling suspension with pendulum suspension
Connect threaded rods GB M8 to dowel using sleeve
VM M8, then mount the C-profile KHA 8 from the
bottom.
5
GB-M8
GB-M10
SES 8x110
SES 10x20
FRS 8x20
KLS 10x20
SEM 8
SEM 10
SEMS 8
AMF22 M10
VM M8
VM M10
US 8x25
US 8x17
US 13x30x6
US 10x21
SD 8/10
SD 8/30
SD 10/10
Support systems | Light-weight designAssembly instruction
Screw tightening torques
Legend Accessories
Underline Symbols
Bolt diameter Strength category screw
(DIN 267 part 3)
Strength category nut
(DIN 267 part 4)
Screw tightening torque
(Nm) acc. VDI 2230
M8 4.6 5 8
M10 4.6 5 16
M12 4.6 5 32
M8 8.8 8 34
M10 8.8 8 68
M12 8.8 8 117
Correct
Wrong
Observe tightening torque for fasteners
6
* The article is not included in the scope of delivery and must be ordered separately.
6 | Ceiling mounting with heavy bracket support
KDU 60
For mounting use two dowels as e.g. SD 10/10*. Attach
the bracket KW using screw set KLS 10x20*. If the
bracket is longer than 500 mm, screw the support piece
KHUSS together with the bracket. The optional
protection cap SU 60* is pushed onto the bracket from
the bottom.
5 | Ceiling mounting with ceiling-fixed bracket
KDAG 41
For mounting use two dowels as e.g. SD 10/10*. Attach
the bracket KA 41 using screw set SES 10x20*,
AMF22 M10*. The optional protection cap SA* is
pushed onto the bracket from the bottom.
4 | Ceiling mounting with head plate BGU 50 and
2x U-profile KHU 50
For mounting use two dowels as e.g. SD 10/10*. Mount
the U-profile using screw set KLS 10x20. For mounting
the bracket KUM use screw set KLS 10x20. The
optional two protection caps SU 50* are pushed onto
the bracket from the bottom.
3 | Ceiling mounting with bracket support KDU 52
For mounting use two dowels as e.g. SD 10/10*. Secure
the bracket KUM using screw set KLS 10x20. The
optional protection cap SU 50* is pushed onto the
bracket from the bottom.
2 | Ceiling mounting with ceiling-fixed bracket
DKSL
For mounting use dowels as e.g. SD 8/30*. The clamp
piece KSL-SP must be positioned first.
1 | Wall mounting with bracket KW
For mounting use dowels as e.g. SD 10/10*.
Assembly instruction for support systems of wire-mesh cable trays, cable trays and cable ladders in concrete.
Support systems | Medium-weight designAssembly instruction
7
* The article is not included in the scope of delivery and must be ordered separately.
11 | Ceiling suspension with pendulum suspension
Connect threaded rods GB M10 to the dowel using
sleeve VM M10. The C-profile KHA 41 is mounted from
the bottom.
10 | Ceiling mounting with head plate BGI with
I-profile KHI
For mounting use two dowels as e.g. SD 10/10*. Attach
the I-profile using screw set FRS 10x30 and SEM 10.
The console mounting of KT or KTS is the same as the
mounting of KDI. The optional protection cap SI* is
pushed onto the bracket from the bottom.
9 | Ceiling mounting with heavy bracket support
KDI
For mounting use two dowels as e.g. SD 10/10*. Fasten
the bracket KTS using the enclosed clamping piece. The
optional protection cap SI* is pushed onto the bracket
from the bottom.
8 | Ceiling mounting with heavy bracket support
KDI
For mounting use two dowels as e.g. SD 10/10*. Fasten
the bracket KT using the enclosed clamping piece. The
optional protection cap SI* is pushed onto the bracket
from the bottom.
7 | Ceiling mounting with head plate BGU 60 and
U-profile KHU 60
For mounting use two dowels as e.g. SD 10/10*. Secure
the U-profile with screw set SES 10x20, SEM 10 and
US 10x21. Bracket mounting KW is done as with KDU
60. The optional protective cap SU 60* is pushed onto
the bracket from the bottom.
Support systems | Medium-weight designAssembly instruction
8
GB-M10
SES 10x20
FRS 10x30
KLS 10x20
SEM 10
AMF22 M10
VM M10
US 10x21
SD 8/30
SD 10/10
Support systems | Medium-weight designAssembly instruction
Screw tightening torques
Legend Accessories
Underline Symbols
Bolt diameter Strength category screw
(DIN 267 part 3)
Strength category nut
(DIN 267 part 4)
Screw tightening torque
(Nm) acc. VDI 2230
M8 4.6 5 8
M10 4.6 5 16
M12 4.6 5 32
M8 8.8 8 34
M10 8.8 8 68
M12 8.8 8 117
Correct
Wrong
Observe tightening torque for fasteners
9
6 | Ceiling suspension with pendulum suspension
Fasten the head plates BGI with two dowels each as
e.g. SD 12/10*. Secure the I-profiles horizontally to the
head plates using screw set FRS 10x30, SEM 10.
Screw the longitudinal profile to the support connector
HKIQ.
5 | Ceiling suspension with pendulum suspension
Fasten the head plates BGU 60 with two dowels each
as e.g. SD 12/10*. Secure the U-profile using the screw
set SES 10x20, SEM 10 and US 10x21 both horizontally
and vertically.
4 | Mounting on steel girders using heavy bracket
KISS
For mounting use four beam clamps SKS M*.
3 | Mounting on steel girders using heavy bracket
KIS
For mounting use four beam clamps SKS H*.
2 | Wall mounting with heavy bracket KWSS
For mounting use dowels as e.g. SD 12/10* for the top
and bottom drill holes.
1 | Wall mounting with heavy bracket KWS
For mounting use dowels as e.g. SD 12/10* in the top
drill hole.
Assembly instruction for support systems of wire-mesh cable trays, cable trays, cable ladders and wide-span cable ladders in concrete.
Support systems | Heavy-weight designAssembly instruction
* The article is not included in the scope of delivery and must be ordered separately.
10
SES 10x20
FRS 10x30
SEM 10
US 10x21
SD 12/10
SKS H
SKS M
Screw tightening torques
Legend Accessories
Underline Symbols
Bolt diameter Strength category screw
(DIN 267 part 3)
Strength category nut
(DIN 267 part 4)
Screw tightening torque
(Nm) acc. VDI 2230
M8 4.6 5 8
M10 4.6 5 16
M12 4.6 5 32
M8 8.8 8 34
M10 8.8 8 68
M12 8.8 8 117
Correct
Wrong
Observe tightening torque for fasteners
Support systems | Heavy-weight designAssembly instruction
11
www.puk.com© PUK Group | PUK-MV KB-TK EN | WEST | 500 | 2016-02-01
Errors and technical modification subject to change, reproduction as well as electronic
duplication only with our written permission. With appearance of this print all preceding
documents lose their validity.
