VESSEL LAVATORY/

CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS

CUT ALONG THIS LINE

239.4mm

RIM OF LAVATORY

WHEN PLOTTING TEMPLATE FULL SIZE:

Make sure horizontal and vertical dimensions

match the dimensions labeled on the template.

�

�

, 2011

Copyright Kohler China Ltd., 2011

1187650-T01-A

K-14223-SR2-

CARAVAN COLLECTION PERSIATM

( )158 :200436

BEFORE YOU BEGINCAUTION: Risk of personal injury or product damage.

Handle with care. Vitreous china can break or chip if the

product is handled carelessly.

Observe all local plumbing and building codes.

Prior to installation, unpack the new lavatory and inspect it

for damage. Return the lavatory to its protective carton

until you are ready to install it.

Inspect the existing drain and supply tubing. Replace if

necessary.

These instructions are for installing the lavatory to wood

frame construction. For other installations, supply suitable

bracing and fastening devices of sufficient size and

strength.

Use the template supplied with the lavatory.

For replacement installations, make sure the existing

cutout is the same size or smaller than needed for the

new lavatory.

Use these instructions for wall-mount, self-rimming and

above counter installations. Follow only the instructions

that apply to your installation.

You can choose between a wall-mount or countertop

faucet installation, depending upon the setting and styling

you desire. A wall-mount faucet is recommended.

Kohler Co. reserves the right to make revisions in the

design of products without notice, as specified in the Price

Book.

Kohler lavatory is made according to American National

Standard that it can match the American lavatory fittings .

Any other lavatory fittings may not fit for kohler lavatory.

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

NOTE: You may require different, morespecialized tools to install this lavatory tocountertop materials other than wood orwood composites.

TOOLS AND MATERIALS(Not Supplied)

Plus:

�

�

�

18mm drill bit

Hole Saw

Safety Shoes

�

�

�

18mm

PREPARATION�

�

�

�

�

�

�

Install the water supplies and drain piping according to theroughing-in information.

The lavatory displayed in the illustration may differfrom your actual product.

Position the template on the countertop.

Provide sufficient spoutoverhang into the lavatory basin. The faucet spout lengthmust be at least 127mm to provide proper performance.

Pay special attention to thespout and handle fit clearance when locating the faucet.Use the template to locate the faucet spout hole centerlineon the countertop. This centerline is recommended toprovide adequate clearance between the edge of thelavatory and the spout.

Check for adequate clearance between the backsplash,faucet spout and handles, and lavatory. Kohler Co.recommends a clearance of at least 25mm.

Refer to the faucet installation instructions for requiredclearance, and mark the preferred faucet hole locationsusing a soft lead pencil.

Trace the template on the countertop.

NOTE:

For Wall-Mount Faucets:

For Countertop Faucets:

Countertop Installations

INSTALL THE LAVATORYCAUTION: Risk of personal injury or product damage.Handle with care. Product can break, chip or cause injury ifhandled carelessly. Get help lifting the lavatory.

Cut out the opening by carefully following the pencil linetraced from the template.

Temporarily set the lavatory into the countertop cutout tocheck for fit.

Remove the lavatory from the countertop.

Drill the faucet holes.

Install the faucet according to the manufacturer sinstructions.

Install the drain. For pop-up drains, use the customlinkage provided with this lavatory instead of the linkagesupplied with the drain.

Install the custom linkage as shown. Adjust and/or bendthe linkage as required to achieve smooth, effective pop-up drain operation. Only bend the linkage at the locationshown.

Apply a 3mm bead of sealant around the countertopcutout hole. Apply the sealant approximately 6mm awayfrom the cutout hole edge.

Set the lavatory into the countertop cutout. Use care toavoid smearing the sealant bead. Wipe away any excesssealant with a clean cloth.

Follow the instructions listed on the sealant label. Allowthe sealant to set for 30 minutes or more beforeproceeding.

Connect and tighten the trap to the drain, and completethe water supply connections to the faucet according tothe instructions packed with the faucet.

Run water into the lavatory and check for leaks.

Clean up with a non-abrasive cleaner.

Countertop Installations�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

127mm

25mm

�

�

�

�

�

�

�

�

�

�

�

�

�

3mm

6mm

30

For best results, keep the following in mind when caring foryour KOHLER product:

Always test your cleaning solution on an inconspicuousarea before applying to the entire surface.

Wipe surfaces clean and rinse completely with waterimmediately after applying cleaner. Rinse and dry anyoverspray that lands on nearby surfaces.

Do not allow cleaners to soak on surfaces.

Use a soft, dampened sponge or cloth. Never use anabrasive material such as a brush or scouring pad toclean surfaces.

Be careful not to leave staining materials in contact withthe surface for extended periods of time.

The ideal cleaning technique is to rinse thoroughly andblot dry any water from the surface after each use.

Do not use the product in the water below 0 C.

�

�

�

�

�

�

�o

� Please do not use hard materials (like scouring pad) toclean product surface, especially the product logo.

�

�

�

�

�

�

� 0 Co

�

CARE AND CLEANING

ROUGHING-IN:

Unit:mm

Kohler reserves the right to change marked dimensions without prior notice.

Height Depth

Outer162

Inner108

Recommened ADA Installation

Reference Value

CL of Fitting

3/8" Hot3/8"

3/8" Cold3/8"

1-1/4" OD1-1/4"

SUGGESTED FAUCET CENTERLINE

Pencil Drill Safety Glasses Screwdriver Tape Measure

Keyhole SawScissors Sealant

254

76

162

356

229

102

51

610

864 686Min

279

203Min

229Min

413

408

Spout Centerline Backsplash

25mm Minimum Clearance25mm

Outside Edge of Lavatory

Cut-out Line

Bend here only.

Adjust here.

Custom Linkage

Lift Rod