Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
Subsea ValvesAPI 6A Small Bore Ball and Needle Valves For Subsea Oil & Gas Exploration
2
Offer of SaleThe items described in this document are available for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. Any sale contract entered into by Parker
will be governed by the provisions stated in Parker’s standard terms and conditions of sale (copy available upon request).
FAILURE, IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries or its authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current
product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.
WARNING
2 3
Page 4
Pages 5-7
Pages 8-9
Subsea Ball Valve, 2-Way, Soft Seat - Overview
Subsea Ball Valve, 2-Way, Soft Seat - Technical Information
Subsea Ball Valve, 2-Way, Soft Seat - Ordering Information
Page 10 Subsea Needle Valve, Non-Rotating Stem - Overview
Pages 11-13 Subsea Needle Valve, Non-Rotating Stem - Technical Information
Pages 14-15 Subsea Needle Valve, Non-Rotating Stem - Ordering Information
4
Feature Benefit Value
PEEK seats Provide resistance to chemicals, heat, and wear/abrasion
Performance and reliability
Self-relieving seats Cavity pressure relief Safety
Low friction, pressure assisted PTFE shaft seal Increases cycle life and reduces operating torque Performance and reliability
Shaft and end adaptor o-ring ingress sealsPrevent water and silt ingress to any threaded or rotating parts
Performance and reliability
Adaptor metallic egress sealNo elastomers in contact with process fluid, therefore no seal deterioration
Performance and reliability
Anti-blow-out stem Prevents stem blow-out Safety
Unobstructed 10 mm flow path Minimizes pressure drop Performance and safety
API 6A compliant materials Compliance with industry standards Safety, performance and reliability
API 17D design validation test including API 6A PR2F protocol Confirmation of a robust design Reliability
Parker’s soft seated quarter turn ball valve for flow isolation, designed specifically to deliver smooth, low-torque performance in subsea applications. Utilising the same design technology as the standard Parker’s Hi-Pro series ball valve, the subsea design incorporates the necessary design alterations to provide a reliable externally pressurised valve for the subsea industry.
Featuring PEEK self-relieving seat and PTFE packing, this subsea ball valve design incorporates additional o-ring seals, which prevent the ingress of sea water into the valve which would adversely affect the operation of the valve as well as contaminate the process liquid.
The bi-directional valves are available in a range of corrosion-resistant alloys and are suitable for equipment located at depths down to 3,050m. The valves are designed to facilitate operation either manually or by a Remotely Operated Vehicle (ROV).
Parker’s subsea ball valves have been designed to meet or exceed the rigorous qualification test requirements of API 6A/17D PSL 3. The structural integrity and performance have been confirmed by independent third party inspectors.
Subsea Ball Valve 2-WaySoft SeatOverview
Features, Benefits and Values
Applications (Liquid media):
• Subsea Hydraulic Manifolds• Subsea Control Umbilicals• Subsea Wellheads and Control Packages• Chemical injection • DBB, bleed, vents, test lines
Markets:
• Upstream Oil & Gas (liquid media)
Subsea 2-way ball valve, soft seated
4 5
Configuration 2-Way, 1/4 turn
Construction 2-Piece, side entry threaded end connector
Ball Design Floating ball
Flow Pattern Bi-directional (liquid)
Minimum Ball Bore Size 10 mm
Maximum Allowable Working Pressure (MAWP)
10,000 psi (689 bar)
Media Temperature RangeClass: P/V -29oC to 121oC (-20F to 250F)
Maximum Sea Depth 3050 m (10,000 ft)
Maximum External Pressure 4,500 psi (310 bar)
End ConnectionsAE Cone-and-ThreadButt WeldNPT
Body Materials
316 Stainless SteelDuplex Stainless SteelSuper DuplexInconel 625
Seat Material PEEK
Principle Standards API 6A/API 17D
Valve Design Code API 6A/API 6X
Valve Test Pressure API 6A PSL3
Safety Factor and Allowable Stress
API 6A/API 17D
Maximum Field Shell Hydrotest Pressure
1.5xMAWP
Specification
API 17D Design and Operation of Subsea Production Systems - Subsea Wellhead and Tree Equipment
API 17H / ISO 13628-8 Design and Operation of Subsea Production Systems: Remotely Operated Vehicle (ROV) interfaces on subsea production systems
API 20F Corrosion Resistant Bolting for use in petroleum and natural gas industries
NACE MR-0175 /ISO15156
Petroleum and natural gas industries - Materials for use in H2S containing environments in oil and gas production
API 6A / ISO 10423 Specification for Wellhead and Christmas Tree Equipment
API 6X Design calculations for pressure containing equipment
BS EN 10204 Metallic Products - Types of Inspection Document
BS EN ISO 9001 Quality Management Systems
Applicable codes and standards
Valve validation testing• Lloyds Witnessed API 17 (Section 5.1.7: Table 3)
including the API 6A PR2F Bi-directional Protocol (PSL3) and the Annex L hyperbaric test
• Test undertaken on Stainless Steel UNS S31600/31603 valves
• Protocol carried out hydrostatically for all ambient temperature parts of test (except for where high pressure gas testing was required by API 6A PR2F)
Breakout Torque (gas at 10,000 psi)
Temperature/Pressure chart
Technical Information
Design Life• API 17D Endurance test qualified
• Cathodic protection down to end user
Normal 11Nm (8ft-lbf)
Maximum* 26Nm (19ft-lbf)
Temperature (oC)(Fahrenheit (oF))
20100-10-20-29 30 40 9080706050
100
200
400
500
600
700
Wor
king
Pre
ssur
e (b
ar)
110100
2,000
4,000
6,000
Working P
ressure (psi)
121(-20.2) (-4) (14) (32) (50) (68) (86) (104) (122) (140) (158) (176) (194) (212) (230) (250)
8,000
10,000
300
Temp Class: P/V (-29oC to 121oC)
Breakout Torque is the torque needed to initially rotate valve when in closed position with full MAWP on one side and 0 psi on the other.* Maximum torque recorded under extreme test conditions.
Subsea Ball Valve 2-WaySoft Seat
6
2
3
6
4
5
7
9
12
13
16
11
8
19
1410
Technical Information
17
18
31
15
7
Bill of Materials
Reference Description 316 Stainless Steel Duplex Stainless Steel Super Duplex Inconel 625 PSLNACE
MR-0175
1 Body ASTM A479 UNS S31600/S31603 ASTM A479 UNS S31803 ASTM A479 UNS S32750 or UNS32760 ASTM B446 UNS N06625 Yes Yes
2 Ball ASTM A479 UNS S31600/S31603 ASTM B446 UNS N06625 ASTM B446 UNS N06625 ASTM B446 UNS N06625 Yes Yes
3 Seats PEEK PEEK PEEK PEEK
4 End Adaptor ASTM A479 UNS S31600/S31603 ASTM A479 UNS S31803 ASTM A479 UNS S32750 or UNS32760 ASTM B446 UNS N06625 Yes Yes
5 Joint Seal ASTM A479 UNS S31600/S31603 ASTM A479 UNS S31245 ASTM B446 UNS N06625 ASTM B446 UNS N06625
6 Shaft (Stem) ASTM A564 UNS S17400 ASTM B446 UNS N06625 ASTM B446 UNS N06625 ASTM B446 UNS N06625 Yes Yes
7 Packing PTFE PTFE PTFE PTFE
8 Shaft O-Ring NBR-90 NBR-90 NBR-90 NBR-90
9 Stop Pin 316Ti Stainless Steel 316Ti Stainless Steel 316Ti Stainless Steel 316Ti Stainless Steel
10 Thrust Bush (Top) 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
11 Thrust Bush (Bottom) 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
12 Thrust Bush (Bottom) Disc Reinforced PTFE Reinforced PTFE Reinforced PTFE Reinforced PTFE
13 Lock Nut A4. Stainless Steel A4. Stainless Steel A4. Stainless Steel A4. Stainless Steel
14 Nut A4. Stainless Steel A4. Stainless Steel A4. Stainless Steel A4. Stainless Steel
15 Internal Gland Thrust Disc Reinforced PTFE Reinforced PTFE Reinforced PTFE Reinforced PTFE
16 Handle 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
17 Handle Grip Plastic Plastic Plastic Plastic
18 Adaptor Ingress O-Ring NBR-90 NBR-90 NBR-90 NBR-90
19 Adaptor Backup Ring PTFE PTFE PTFE PTFE
20 Adaptor Stop Pin 316Ti Stainless Steel 316Ti Stainless Steel 316Ti Stainless Steel 316Ti Stainless Steel
Inlet/Outlet
Dimension Weight(Valve with handle)A B C D E F G
mm inch mm inch mm inch mm inch mm inch mm inch mm inch kg
9/16” MP 104.7 4.12 170.6 6.72 129.7 5.11 96.8 3.81 38.1 1.50 44.3 1.75 44.3 1.75 1.50
3/4” MP 115.9 4.56 175.4 6.9 129.7 5.11 96.8 3.81 38.1 1.50 44.3 1.75 44.3 1.75 1.54
ITEM QTY DESC MATERIAL
1 1 BODY ST. STL ASTM A479 UNS S31600/S31603
2 1 BALL ST. STL ASTM A479 UNS S31600/S31603
3 2 SEAT P.E.E.K
4 1 JOINT SEAL ST. STL ASTM A479 UNS S31600/S31603
5 1 BACK UP RING P.T.F.E.
6 1 ADAPTOR O-RING N.B.R
7 1 ADAPTOR ST. STL ASTM A479 UNS S31600/S31603
8 1 PACKING P.T.F.E.
9 1 SHAFT O-RING N.B.R
10 1 TEST HANDLE 316 ST.STL
11 1 SHAFT ST. STL ASTM A564/A564M UNS S17400
12 1 LOCK NUT A4. ST.STL
13 1 NUT A4. ST.STL
14 1 THRUST BUSH (TOP) 316 ST.STL
15 1 THRUST BUSH (BOTTOM) 316 ST.STL
16 1 BOTTOM THRUST BUSH DISC REINFORCED P.T.F.E
17 1 INTERNAL GLAND THRUST SEALREINFORCED P.T.F.E
Parts List
DESCRIPTIONPART NUMBERQTYITEM
BALL VALVE PHANTOMIPDEAB794 HI-PRO-316-PTFE-HP-PHTM Hi Pro 10mm110
SSBV SOFT SEATED 10MM BODY 3/4" MP CONE AND
THREAD
IPDEAB798 SS1HPB00113
ORING - BS012 - 9.25 X 1.7814
ORING - BS121 - 2.62x26.6416
Back Up Ring 00-121busp15
PEEK SEAT - 10MM BORE HI-PRO BALLVALVE /
PROBLOC
BSE001-PEEK212
SUBSEA 10KSI HI-PRO 10MM END ADAPTORIPDEAB805113
STOP PINIPDEAB823 BSPXXX-S9115
Parts List
DESCRIPTIONPART NUMBERQTYITEM
BALL VALVE PHANTOMIPDEAB794 HI-PRO-316-PTFE-HP-PHTM Hi Pro 10mm110
SSBV SOFT SEATED 10MM BODY 3/4" MP CONE AND
THREAD
IPDEAB798 SS1HPB00113
ORING - BS012 - 9.25 X 1.7814
ORING - BS121 - 2.62x26.6416
Back Up Ring 00-121busp15
PEEK SEAT - 10MM BORE HI-PRO BALLVALVE /
PROBLOC
BSE001-PEEK212
SUBSEA 10KSI HI-PRO 10MM END ADAPTORIPDEAB805113
STOP PINIPDEAB823 BSPXXX-S9115
Parts List
DESCRIPTIONPART NUMBERQTYITEM
BALL VALVE PHANTOMIPDEAB794 HI-PRO-316-PTFE-HP-PHTM Hi Pro 10mm1
SSBV SOFT SEATED 10MM BODY 3/4" MP CONE AND
THREAD
IPDEAB798 SS1HPB0011
ORING - BS012 - 9.25 X 1.781
ORING - BS121 - 2.62x26.641
Back Up Ring 00-121busp1
PEEK SEAT - 10MM BORE HI-PRO BALLVALVE /
PROBLOC
BSE001-PEEK2
SUBSEA 10KSI HI-PRO 10MM END ADAPTORIPDEAB8051
STOP PINIPDEAB823 BSPXXX-S91
A
F
E
D
C
B
G
H
I
J
1 32 54 9876 10
Filename:IPDEAB Hi-PRO GA for catalogue.idw
ALL DIMENSIONS IN mm WITH IMPERIAL EQUIVALENTS IN PARENTHESIS
DRAWING TITLE :UNLESS STATED
3rd ANGLEPROJECTION
THIS DRAWING, THE MARKET AND BUSINESS STRATEGY INFORMATION (CONTAINED OR EXPRESSED), TOGETHER WITH ALL INNOVATIONS, DESIGNS, INVENTIONS, SYSTEMS AND PROCESSES SHOWN OR DISCUSSED ARE THE SOLE PROPERTY AND COPYRIGHT OF PARKER HANNIFIN PLC. THIS DRAWING IS FURNISHED ON THE UNDERSTANDING THAT THE DRAWING AND THE INFORMATION IT CONTAINS WILL NOT BE COPIED OR DISCLOSED TO OTHERS EXCEPT WITH THE WRITTEN CONSENT OF PARKER HANNIFIN, WILL NOT BE USED TO THE DETRIMENT OF PARKER HANNIFIN, AND WILL BE RETURNED UPON REQUEST BY PARKER HANNIFIN. THIS INTELLECTUAL PROPERTY CANNOT BE USED, REPRODUCED, COPIED, TRANSFERRED OR COMMUNICATED IN ANY WAY BY OR TO THIRD PARTIES. FURTHER DESIGN, PATENT AND COPYRIGHTS IN RESPECT OF PRODUCT AND COMPONENTS ALSO EXIST. YOUR ADHERENCE TO THE ABOVE CLAIM IS IMPLICIT UPON YOUR USE OF THIS DRAWING. THE ITEMS DESCRIBED IN THIS DOCUMENT, INCLUDING WITHOUT LIMITATION, PRODUCT FEATURES, SPECIFICATIONS, DESIGNS, AVAILABILITY AND PRICING, ARE SUBJECT TO CHANGE BY PARKER HANNIFIN CORPORATION AND ITS SUBSIDIARIES AT ANY TIME WITHOUT NOTICE.
DO NOT SCALE IF IN DOUBT ASK WWW.PARKER.COM/IPDREV No.
ECO NO. :
Version No.
ECO DATE:
DRAWN BY: DRAWN DATE:
CHECKED & APPROVED BY: Approvals Using Electronic 'ENOVIA ECO WORKFLOW'
© 2020DESCRIPTION OF REV / VERSION CHANGE
ENGINEERING SUCCESS.YOUR
SUBSEA 10KSI HI-PRO GA FOR CATALOGUE
CUSTOMER ASSEMBLY DRAWING
ECO-
-
Alastair Burls
-
FOR MARKETING SUBSEA BALL VALVE
22/03/2020
22/03/2020
A
44.3[1.75]
44.3[1.75]
96.8[3.81]
THERE AREHIDDEN
COLUMNS INTHIS
SPREADSHEET,DOUBLE CLICK
TO OPEN INEXCEL
38.1[1.50]
A/F HEX.
129.7[5.11]
B
Column 1 Column 2 Column 3 Column 4 Column 5 Column 6 Column 7
A (mm) A(In) B(mm) B(In) APPROX. MASS (kg) APPROX. MASS (lb)
S2BS8S10PKM9-H 104.7 4.12 170.6 6.72 1.5 3.3
S2BS8S10PKM12-H 115.9 4.56 175.4 6.9 1.54 3.4B
A
129.7[5.11]
38.1[1.50]
A/F HEX.
96.8[3.81]
44.3[1.75]
44.3[1.75]
C
D
E
F
G
Dimensions and Weight
Dimensions for reference only and subject to change. Contact Parker for other dimensions.
Subsea Ball Valve 2-WaySoft Seat
8
Series
Subsea 2-Way Ball Valve Soft Seat
S2BS
Bore Size
10 mm 8
S2BS 10
Body Material
316 Stainless Steel S
Duplex Stainless Steel E
Super Duplex F
Inconel 625 M
M68 S
Pressure
10,000 psi 10
Options
Handle H
ROV Low Torque Paddle P
NACE Material, Hardness
Verification/Certificate
N
Seat Material
PEEK PK
PK HN-
End Connection
3/8” MP M6
9/16” MP M9
3/4” MP M12
3/8” BW 6B
1/2” BW 8B
3/8” NPT 6N
1/2” NPT 8N
Example part number: S2BS8S10PKM6-HN
Notes:
1. All valves with cone and thread connection include collars and gland nuts.2. Buttweld adaptor options are available (pressure rating dependent on configuration) - contact Parker
Instrumentation Products Division Europe. 3. These valves are adaptable for Remotely Operated Vehicle (ROV) operation. See paddle design on the next page.4. ROV bucket designs can be provided on request. 5. Certification requirements and customer specifications MUST be provided at enquiry and order stage.6. Contact Parker Instrumentation Products Division Europe technical support on +44 (0)1271 3131 or your local
distributor for information on other options.
Ordering Information
9
A
F
E
D
C
B
G
H
I
J
1 32 54 9876 10
Filename:S2BS8S10PKM12-P G.A FOR CATALOGUE.idw
FOR MATERIAL AND PROCESS SPECIFICATIONS REFER TO GENERIC PROCESS CONTROL SHEET - 106
FOR PART MARKING DETAILS REFER TO PART MARKING SPECIFICATION - N/A
REV No.
ECO No.
DRAWN BY:
DRAWN DATE:
ALL DIMENSIONS IN mm UNLESS OTHERWISE STATED
DRAWING TITLE :
REMOVE ALL SHARP EDGES AND BURRS
INCH METRIC ANGULAR
(.00") ±.015"(.000") ±.005"
(.0)mm ±.3mm(.00mm) ±0.1mm
±1/2°±30'
GENERAL M/C FINISH 63min CLA/ 1.6mm RAGEOMETRICAL TOL'S TO BS.308 PART 3.
ALL THREAD TOLERANCES ARE TO BE IN ACCORDANCE WITH PARKER IPD ESST01.
DO NOT SCALE IF IN DOUBT ASK
UNLESS STATED3rd ANGLE
PROJECTION Parker Hannifin Manufacturing LtdInstrumentation Products Division EuropeRiverside RoadBarnstapleDevonEX31 1NP+44 (0)1271 313131
CHECKED & APPROVED BY: Approvals Using Electronic'Enovia ECO Workflow' - SEE 'ECO NO.'
PART SIMILAR TO
O.WRIGHT
29/04/2020
SUBSEA 10KSI HI-PRO 10MM BALL VALVE PADDLE GA
S2BS8S10PKM12-P
4
ECO-
THIS DRAWING CONTAINS INFORMATION THAT IS CONFIDENTIAL AND PROPRIETARY TO PARKER HANNIFIN. THIS DRAWING IS FURNISHED ON THE UNDERSTANDING THAT THE DRAWING AND THE INFORMATION IT CONTAINS WILL NOT BE COPIED OR DISCLOSED TO OTHERS EXCEPT WITH THE WRITTEN CONSENT OF PARKER HANNIFIN, WILL NOT BE USED TO THE DETRIMENT OF PARKER HANNIFIN, AND WILL BE RETURNED UPON REQUEST BY PARKER HANNIFIN.
ECO DATE:10,000 PSI RANGE
ASSEMBLY DRAWING
A
160.7(6.33")
A (mm) A(In) APPROX. MASS (kg) APPROX. MASS (lb)
S2BS8S10PKM9-P 104.7 4.12 2.09 4.6
S2BS8S10PKM12-P 115.9 4.56 2.13 4.7
A
63.5(2.50")
63.5[2.50]
160.7[6.33]
44.5(1.75")
44.5(1.75")
38.1(1.5")HEXA/F
38.1(1.5")HEXA/F
44.5(1.75")
45.6(1.61")
45.6[1.80]
9.5(0.49"
12.5[0.49]
70.0(2.76")
116.4[4.58] PADDLE CAP
HEAD SCREWM10x30
31.4[1.24]
70.0[2.76]
4x OFF MOUNTING M6x1 HOLES
34.9[1.38]
34.0[1.34]
58.0[2.28]
Paddle and Hub 0.728 kgValve Assembly 2.114 kg
ROV Low Torque Paddle
Parker’s subsea ball valves can be ordered with a paddle for ROV operation.
Dimensions and Weights
Inlet
/Outlet
Dimension Weight(Valve with
paddle)A B C D E F G H I J K L Mmm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch kg
9/16” MP 104.7 4.12 40.9 1.61 160.7 6.33 12.5 0.49 57.0 2.24 34.9 1.38 34.0 1.34 63.5 2.50 70.0 2.76 116.4 4.58 44.5 1.75 38.1 1.50 31.4 1.24 2.08
3/4” MP 115.9 4.56 45.7 1.80 160.7 6.33 12.5 0.49 57.0 2.24 34.9 1.38 34.0 1.34 63.5 2.50 70.0 2.76 116.4 4.58 44.5 1.75 38.1 1.50 31.4 1.24 2.11
B
C
E
F (A/F)
G
H
I
J
K
L(HEXA/F)
M
Description Material
Paddle ASTM A240 UNS S31600
Paddle hub ASTM A479 UNS S31600/S31603
Paddle cap head screw 316 Stainless Steel
Paddle Bill of Materials
A
D
10
Parker’s non-rising, non-rotating stem needle valve designed specifically to deliver smooth, low-torque performance in subsea applications. Featuring metal-to-metal seat for bubble-tight shut-off, longer stem/seat life, greater durability for repeated on/off cycles and reinforced PTFE/PEEK chevron packing below stem threads for dependable stem and body sealing. This subsea needle valve incorporates additional o-ring seals, which prevent the ingress of sea water into the valve which could adversely affect the operation of the valve as well as contaminate the process fluid.
The uni-directional valves are available in a range of corrosion-resistant alloys and are suitable for equipment located at depths down to 3,050m. The valves are designed to facilitate operation either manually or by a Remotely Operated Vehicle (ROV).
Parker’s subsea needle valves have been designed to meet or exceed the rigorous qualification test requirements of API 6A/17D PSL 3/3G. The structural integrity and performance have been confirmed by independent third party tests.
Subsea Needle Valve Non-Rising, Non-Rotating StemOverview
Applications:
• Subsea Hydraulic Manifolds• Subsea Control Umbilicals• Subsea Wellheads and Control Packages• Chemical injection • DBB, bleed, vents, test lines
Feature Benefit ValueNon-rising, non-rotating stem Protects against stem galling and seat damage Performance and reliability
Bolted bonnet constructionProtection of threads from process fluid, ease of disassembly and maintenance
Safety and reliability
Metal-to-Metal seats Bubble-tight shut-off, longer stem/seat life, greater durability for repeated on/off cycles and excellent corrosion resistance
Performance and reliability
Low friction, pressure assisted PEEK and PTFE chevron packing Increases cycle life and reduces operating torque Performance and reliability
Double o-ring stem ingress seals on bonnet housing
Prevent water and silt ingress to any threaded or rotating parts
Safety
API 6A compliant materials Compliance with industry standardsSafety, performance and reliability
API 17D design validation test including API 6A PR2F protocol carried out pneumatically Confirmation of a robust design Reliability
Features, Benefits and Values
Markets:
• Upstream Oil & Gas
Subsea needle valve, non-rising, non-rotating stem
10
Valve Design Non-Rotating Stem
Configuration 2-Way Straight
Construction 3-Piece, bolted bonnet
Flow Pattern Uni-directional
Minimum Seat Bore Size 12 mm
Maximum Allowable Working Pressure (MAWP) 10,000 psi (689 bar)
Media Temperature RangeClass: P/V -29oC to 121oC (-20F to 250F)
Maximum Sea Depth 3050 m (10,000 ft)
Maximum External Pressure 4,500 psi (310 bar)
End ConnectionsAE Cone-and-ThreadButt WeldNPT
Body Materials
316 Stainless SteelDuplex Stainless SteelSuper DuplexInconel 625
Seat Metal-to-Metal
Principle Standards API 6A/API 17D
Valve Design Code API 6A/API 6X
Valve Test Pressure API 6A PSL3/3G
Safety Factor and Allowable Stress API 6A/API 17D
Maximum Field Shell Hydrotest Pressure 1.5xMAWP
Specification
11
Applicable codes and standards
Valve validation testing• Lloyds Witnessed API 17D (Section 5.1.7: Table 3)
including the API 6A PR2F Bi-directional Protocol (PSL3/3G) and the Annex L hyperbaric test
• Test undertaken on Stainless Steel UNS S31600/31603 valves
• Other than hydrostatic elements of the FAT and hyperbaric testing the Protocol was carried out pneumatically for all internal pressure testing
Design Life• API 17D Endurance test qualified
• Cathodic protection down to end user
Closing Torque (gas at 10,000 psi)
Temperature/Pressure chart
Technical Information
API 17D / ISO 13628-4 Design and Operation of Subsea Production Systems - Subsea Wellhead and Tree Equipment
API 17H / ISO 13628-8 Design and Operation of Subsea Production Systems: Remotely Operated Vehicle (ROV) interfaces on subsea production systems
API 20F Corrosion Resistant Bolting for use in petroleum and natural gas industries
NACE MR-0175 /ISO15156
Petroleum and natural gas industries - Materials for use in H2S containing environments in oil and gas production
API 6A / ISO 10423 Specification for Wellhead and Christmas Tree Equipment
API 6X Design calculations for pressure containing equipment
BS EN 10204 Metallic Products - Types of Inspection Document
BS EN ISO 9001 Quality Management Systems
Temperature (oC)(Fahrenheit (oF))
20100-10-20-29 30 40 9080706050
100
200
400
500
600
700
Wor
king
Pre
ssur
e (b
ar)
110100
2,000
4,000
6,000
Working P
ressure (psi)
121(-20.2) (-4) (14) (32) (50) (68) (86) (104) (122) (140) (158) (176) (194) (212) (230) (250)
8,000
10,000
300
Temp Class: P/V (-29oC to 121oC)
Number of rotations to fully open and close: Max. 5
Normal 42.5Nm (31.3ft-lbf)
Maximum* 65Nm (48ft-lbf)
Closing Torque is the torque required to re-seat the valve.* Maximum torque recorded under extreme test conditions.
12
Subsea Needle Valve Non-Rising, Non-Rotating Stem
4
16
17
20
8
15 3
6
9
5
11
714
11
1
19
2
9
13 12
13
Bill of Materials
Reference Description 316 Stainless Steel Duplex Stainless Steel Super Duplex Inconel 625 PSLNACE
MR-0175
1 Body ASTM A479 UNS S31600/S31603 ASTM A479 UNS S31803 ASTM A479 UNS S32750 or UNS32760 ASTM B446 UNS N06625 Yes Yes
2 Bonnet ASTM A479 UNS S31600/S31603 ASTM A479 UNS S31803 ASTM A479 UNS S32750 or UNS32760 ASTM B446 UNS N06625 Yes Yes
3 Bonnet Top ASTM A479 UNS S31600/S31603 ASTM A479 UNS S31803 ASTM A479 UNS S32750 or UNS32760 ASTM B446 UNS N06625 Yes Yes
4 Lower Stem ASTM A564 UNS S17400 API 6A UNS N07718 API 6A UNS N07718 API 6A UNS N07718 Yes Yes
5 Upper Stem ASTM A479 UNS S20910 ASTM UNS S20910 ASTM A479 UNS S20910 ASTM B446 UNS N06625 Yes Yes
6 Thrust Bush ASTM B150 UNS C63000 ASTM B150 UNS C63000 ASTM B150 UNS C63000 ASTM B150 UNS C63000
7 Bonnet lower O-ring NBR-90 NBR-90 NBR-90 NBR-90
8 Bonnet top O-ring NBR-90 NBR-90 NBR-90 NBR-90
9 Upper Stem O-ring NBR-90 NBR-90 NBR-90 NBR-90
10 (11-14) Chevron Packing N/A N/A N/A N/A
11 Bottom Adaptor PEEK PEEK PEEK PEEK
12 V-Ring (PEEK) PEEK PEEK PEEK PEEK
13 V-Ring (PTFE) Reinforced PTFE Reinforced PTFE Reinforced PTFE Reinforced PTFE
14 Top Adaptor PEEK PEEK PEEK PEEK
15 Bolts A453 Gr 660 D A453 Gr 660 D A453 Gr 660 D A453 Gr 660 D Yes Yes
16 Handle bar 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
17 Handle hub 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
18 Handle cap head screw 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
19 Handle locking grub screw 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
20 Hub locking grub screw 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
A
F
E
D
C
B
G
H
I
J
1 32 54 9876 10
Filename:SSSN GA FOR CATALOGUE.idw
ALL DIMENSIONS IN mm WITH IMPERIAL EQUIVALENTS IN PARENTHESIS
DRAWING TITLE :UNLESS STATED
3rd ANGLEPROJECTION
THIS DRAWING, THE MARKET AND BUSINESS STRATEGY INFORMATION (CONTAINED OR EXPRESSED), TOGETHER WITH ALL INNOVATIONS, DESIGNS, INVENTIONS, SYSTEMS AND PROCESSES SHOWN OR DISCUSSED ARE THE SOLE PROPERTY AND COPYRIGHT OF PARKER HANNIFIN PLC. THIS DRAWING IS FURNISHED ON THE UNDERSTANDING THAT THE DRAWING AND THE INFORMATION IT CONTAINS WILL NOT BE COPIED OR DISCLOSED TO OTHERS EXCEPT WITH THE WRITTEN CONSENT OF PARKER HANNIFIN, WILL NOT BE USED TO THE DETRIMENT OF PARKER HANNIFIN, AND WILL BE RETURNED UPON REQUEST BY PARKER HANNIFIN. THIS INTELLECTUAL PROPERTY CANNOT BE USED, REPRODUCED, COPIED, TRANSFERRED OR COMMUNICATED IN ANY WAY BY OR TO THIRD PARTIES. FURTHER DESIGN, PATENT AND COPYRIGHTS IN RESPECT OF PRODUCT AND COMPONENTS ALSO EXIST. YOUR ADHERENCE TO THE ABOVE CLAIM IS IMPLICIT UPON YOUR USE OF THIS DRAWING. THE ITEMS DESCRIBED IN THIS DOCUMENT, INCLUDING WITHOUT LIMITATION, PRODUCT FEATURES, SPECIFICATIONS, DESIGNS, AVAILABILITY AND PRICING, ARE SUBJECT TO CHANGE BY PARKER HANNIFIN CORPORATION AND ITS SUBSIDIARIES AT ANY TIME WITHOUT NOTICE.
DO NOT SCALE IF IN DOUBT ASK WWW.PARKER.COM/IPDREV No.
ECO NO. :
Version No.
ECO DATE:
DRAWN BY: DRAWN DATE:
CHECKED & APPROVED BY: Approvals Using Electronic 'ENOVIA ECO WORKFLOW'
© 2019DESCRIPTION OF REV / VERSION CHANGE
ENGINEERING SUCCESS.YOUR
SUBSEA 1-2'' NEEDLE VALVE
CUSTOMER ASSEMBLY DRAWING
ECO-0309720
TECHM
-
SNV8_10M9-12-H
06/11/2019
06/11/2019
3/4" MEDIUM PRESSURE CONE & THREAD INLET/OUTLET
44.5[1.75]
209.6[8.25]
36.5[1.44]REF.
260.0[10.24]76.2
[3.00]
20.7[0.81]
40.9[1.61]
52.0[2.05]
33.0[1.30]
76.2[3.00]
111.9[4.41]
2x MOUNTING 10.1 (0.398") HOLES
Dimensions and Weight
3/4” MP Cone-and-Thread Inlet/Outlet
Dimensions for reference only and subject to change. Contact Parker for other dimensions.
Inlet/Outlet Weight (Valve with handle)
3/4” MP 3.8 kg
Weight
14
Series
Subsea Non-Rotating Stem Needle Valve
SNV
Bore Size
12 mm 8
SNV 10
Body Material
316 Stainless Steel S
Duplex Stainless Steel E
Super Duplex F
Inconel 625 M
8 S
Pressure
10,000 psi 10
Options
Handle H
ROV Low Torque Paddle P
NACE Material, Hardness
Verification/CertificateN
Configuration
2-Way Straight
1
M6 HN-
End Connection
3/8” MP M6
9/16” MP M9
3/4” MP M12
3/8” BW 6B
1/2” BW 8B
3/8” NPT 6N
1/2” NPT 8N
Example part number: SNV8S10M61-HN
Notes:
1. All valves with cone and thread connection include collars and gland nuts.2. The standard offering of buttweld connections is achieved by using male to male adaptors - cone and thread
to buttweld connection (pressure rating dependent on configuration). Contact Parker Instrumentation Products Division Europe for other options.
3. These valves are adaptable for Remotely Operated Vehicle (ROV) operation. See paddle design on the next page. 4. ROV bucket designs can be provided on request. 5. Certification requirements and customer specifications MUST be provided at enquiry and order stage.6. Contact Parker Instrumentation Products Division Europe technical support on +44 (0)1271 3131 or your local
distributor for information on other options.
1
Subsea Needle Valve Non-Rising, Non-Rotating StemOrdering Information
15
A
F
E
D
C
B
G
H
I
J
1 32 54 9876 10
Filename:SNV8S10M121-P FOR CATALOGUE.idw
FOR MATERIAL AND PROCESS SPECIFICATIONS REFER TO GENERIC PROCESS CONTROL SHEET - 100
FOR PART MARKING DETAILS REFER TO PART MARKING SPECIFICATION - N/A
REV No.
ECO No.
DRAWN BY:
DRAWN DATE:
ALL DIMENSIONS IN mm UNLESS OTHERWISE STATED
DRAWING TITLE :
REMOVE ALL SHARP EDGES AND BURRS
INCH METRIC ANGULAR
(.00") ±.015"(.000") ±.005"
(.0)mm ±.3mm(.00mm) ±0.1mm
±1/2°±30'
GENERAL M/C FINISH 63min CLA/ 1.6mm RAGEOMETRICAL TOL'S TO BS.308 PART 3.
ALL THREAD TOLERANCES ARE TO BE IN ACCORDANCE WITH PARKER IPD ESST01.
DO NOT SCALE IF IN DOUBT ASK
UNLESS STATED3rd ANGLE
PROJECTION Parker Hannifin Manufacturing LtdInstrumentation Products Division EuropeRiverside RoadBarnstapleDevonEX31 1NP+44 (0)1271 313131
CHECKED & APPROVED BY: Approvals Using Electronic'Enovia ECO Workflow' - SEE 'ECO NO.'
PART SIMILAR TO
O.WRIGHT
30/04/2020
SUBSEA 1-2'' NEEDLE VALVE PADDLE GA
SNV8S10M12-P
ECO-
THIS DRAWING CONTAINS INFORMATION THAT IS CONFIDENTIAL AND PROPRIETARY TO PARKER HANNIFIN. THIS DRAWING IS FURNISHED ON THE UNDERSTANDING THAT THE DRAWING AND THE INFORMATION IT CONTAINS WILL NOT BE COPIED OR DISCLOSED TO OTHERS EXCEPT WITH THE WRITTEN CONSENT OF PARKER HANNIFIN, WILL NOT BE USED TO THE DETRIMENT OF PARKER HANNIFIN, AND WILL BE RETURNED UPON REQUEST BY PARKER HANNIFIN.
ECO DATE:10,000 PSI RANGE
ASSEMBLY DRAWING
288.4(11.31")
44.5(1.75")
76.2(3.00")
12.5(0.49")
63.5(2.50")
70.0(2.76")
288.4[11.35]
34.9[1.38]
A/F
33.0[1.30]
52.0[2.05]
44.5[1.75]
12.5[0.49]
HUB LOCKING GRUB SCREW
PADDLE CAP HEAD SCREW
M10x30
70.0[2.76]
11.5[0.45]
46.5[1.83]
12.0[0.47]
10.1[0.397]
76.2[3.00]
2x MOUNTING M6x1 HOLESBOTH SIDES
26.5[1.04]
63.5[2.50]
3
1
2
2x MOUNTING HOLES
ROV Low Torque Paddle
Parker’s subsea needle valves can be ordered with a paddle for ROV operation.
Paddle Bill of Materials
Description Material
Paddle ASTM A240 UNS S31600
Paddle hub ASTM A479 UNS S31600/S31603
Paddle cap head screw 316 Stainless Steel
Inlet/Outlet Weight (Valve with paddle)
3/4” MP 4.2 kg
Weight
16
Acronym Title Description
API American Petroleum Institute The American Petroleum Institute (API) is the largest U.S. trade association for the oil and natural gas industry.
PSL Product Specification Level Material compliance and factory acceptance testing
NDE Non Destructive Examination Volumetric and surface non destructive testing
FAT Factory Acceptance Test Pressure testing
Serialization An assignment of a unique code to individual parts and / or pieces of equipment to maintain records
Commonly used terms when conducting business with Parker
API 6A - Quality control for bodies, bonnets, end and outlet connections - PSL 3/3G - Parker Compliance
API Product
Specification LevelAPI Sub-Clause
Additional Industry
Codes
PSL3/3G material testing includes:
Tensile testing PSL 3/3G 6.3.2.2 ASTM A370
Impact testing PSL 3/3G 6.3.2.3 ASTM A370
PSL3/3G NDE includes:
Dimensional inspection to Parker standard 10.4.2.5
Traceability PSL 3/3G 10.4.2.8
Chemical analysis PSL 3/3G 6.3.5 ASTM A388
Volumetric NDE PSL 3/3G 10.4.12.12 ASTM E165 / ASTM E709
Surface NDE PSL 3/3G- 10.4.2.10 & 10.4.2.11
Serialization PSL 3/3G 10.4.2.9
Ferritoscope: On request to Parker standard
NORSOK M630 Additional testing includes*:
Corrosion testing
Micrographic examination ASTM G48
Ferrite counting ASTM A923
* (Duplex and Super Duplex materials only) ASTM E562
API 6A - Quality control requirements for regular and Venturi bore valves - PSL3/3G - Parker Compliance
Product Specification Level Parker Comments
Factory Acceptance testing: PSL3 PSL 3G
Hydrostatic test (extended)Body 11.2.3 11.2.3
Seat 11.2.4 11.2.4
Gas testBody - 11.3.3
Seat - 11.3.4
Traceability 10.4.7.2 10.4.7.2 Providing HCT 3.1B is selected
Serialization 10.4.7.3 10.4.7.3 Each tested assembly will have serial number against works order no.
17
Notes
18
Notes
© 2020 Parker Hannifin Corporation. All rights reserved
4190-SBSV 07/2020Parker Hannifin Manufacturing LtdInstrumentation Products Division EuropeRiverside RoadPottington Business ParkBarnstaple, Devon, EX31 1NPUnited KingdomTel.: +44 (0) 1271 313131www.parker.com/ipd
Parker Hannifin CorporationInstrumentation Products Division1005 A Cleaner WayHuntsvilleAL 35805USATel: + 1 (256) 881-2040www.parker.com/ipd
Parker Worldwide
European Product Information Centre
Free phone: 00 800 27 27 5374
(from AT, BE, CH, CZ, DE, DK, EE, EI, ES, FI, FR, IT,
NL, NO, PL, RU, SE, SK, UK, ZA)
Europe, Middle East, AfricaAE – United Arab Emirates, Dubai Tel: +971 4 8127100 [email protected]
AT – Austria, Wiener Neustadt Tel: +43 (0)2622 23501-0 [email protected]
AT – Eastern Europe, Wiener Neustadt Tel: +43 (0)2622 23501 900 [email protected]
AZ – Azerbaijan, Baku Tel: +994 50 2233 458 [email protected]
BE/LU – Belgium, Nivelles Tel: +32 (0)67 280 900 [email protected]
BG – Bulgaria, Sofia Tel: +359 2 980 1344 [email protected]
BY – Belarus, Minsk Tel: +48 (0)22 573 24 00 [email protected]
CH – Switzerland, Etoy Tel: +41 (0)21 821 87 00 [email protected]
CZ – Czech Republic, Klecany Tel: +420 284 083 111 [email protected]
DE – Germany, Kaarst Tel: +49 (0)2131 4016 0 [email protected]
DK – Denmark, Ballerup Tel: +45 43 56 04 00 [email protected]
ES – Spain, Madrid Tel: +34 902 330 001 [email protected]
FI – Finland, Vantaa Tel: +358 (0)20 753 2500 [email protected]
FR – France, Contamine s/Arve Tel: +33 (0)4 50 25 80 25 [email protected]
GR – Greece, Athens Tel: +30 210 933 6450 [email protected]
HU – Hungary, Budaörs Tel: +36 23 885 470 [email protected]
IE – Ireland, Dublin Tel: +353 (0)1 466 6370 [email protected]
IT – Italy, Corsico (MI) Tel: +39 02 45 19 21 [email protected]
KZ – Kazakhstan, Almaty Tel: +7 7273 561 000 [email protected]
NL – The Netherlands, Oldenzaal Tel: +31 (0)541 585 000 [email protected]
NO – Norway, Asker Tel: +47 66 75 34 00 [email protected]
PL – Poland, Warsaw Tel: +48 (0)22 573 24 00 [email protected]
PT – Portugal, Leca da Palmeira Tel: +351 22 999 7360 [email protected]
RO – Romania, Bucharest Tel: +40 21 252 1382 [email protected]
RU – Russia, Moscow Tel: +7 495 645-2156 [email protected]
SE – Sweden, Spånga Tel: +46 (0)8 59 79 50 00 [email protected]
SK – Slovakia, Banská Bystrica Tel: +421 484 162 252 [email protected]
SL – Slovenia, Novo Mesto Tel: +386 7 337 6650 [email protected]
TR – Turkey, Istanbul Tel: +90 216 4997081 [email protected]
UA – Ukraine, Kiev Tel: +48 (0)22 573 24 00 [email protected]
UK – United Kingdom, Warwick Tel: +44 (0)1926 317 878 [email protected]
ZA – South Africa, Kempton Park Tel: +27 (0)11 961 0700 [email protected]
North AmericaCA – Canada, Milton, Ontario Tel: +1 905 693 3000
US – USA, Cleveland Tel: +1 216 896 3000
Asia PacificAU – Australia, Castle Hill Tel: +61 (0)2-9634 7777
CN – China, Shanghai Tel: +86 21 2899 5000
HK – Hong Kong Tel: +852 2428 8008
IN – India, Mumbai Tel: +91 22 6513 7081-85
JP – Japan, Tokyo Tel: +81 (0)3 6408 3901
KR – South Korea, Seoul Tel: +82 2 559 0400
MY – Malaysia, Shah Alam Tel: +60 3 7849 0800
NZ – New Zealand, Mt Wellington Tel: +64 9 574 1744
SG – Singapore Tel: +65 6887 6300
TH – Thailand, Bangkok Tel: +662 186 7000
TW – Taiwan, Taipei Tel: +886 2 2298 8987
South AmericaAR – Argentina, Buenos Aires Tel: +54 3327 44 4129
BR – Brazil, Sao Jose dos Campos Tel: +55 800 727 5374
CL – Chile, Santiago Tel: +56 2 623 1216
MX – Mexico, Toluca Tel: +52 72 2275 4200