Submittal Transmittal Banner Tatum/Grnway - Const Project ...€¦ · Fig. 1 and 3, are a friction fit assembly allowing for 3/4-inch (19mm) and 1/2-inch (12.7mm) of adjustment, respectively

Detailed, Grouped by Each Number

Submittal Transmittal

Kitchell Contractors Inc. of AZBanner Tatum/Grnway - Const Project # 6060B

4720 E GREEWAY ROAD

PHOENIX, AZ 85032

Tel: Fax:

Date: 12/17/2015 Reference Number: 0049

Transmitted To: Transmitted By: Matt KirchErik Denk

AERO AUTOMATIC SPRINKLER CO Kitchell Contractors Inc. of AZ

21650 N CENTRAL AVENUE

PHOENIX, AZ 85024

1707 E Highland, Suite 100

Phoenix, AZ 85016

Tel: (602) 222-5300

Fax: (602) 263-8593

Submittal Package No Description Due Date Package ActionQty

Approved as Noted12/21/2015Fire System Equipment and Material0001 - 21 13 13 - 019

Transmitted For Delivered Via Tracking Number

E-mailConstruction

Notes Item ActionItems DescriptionQty

0001 F1FR56 Upright For Construction

0002 F1FR56 Recessed Pendent For Construction

0003 F1FR56 Horizontal Sidewall For Construction

0004 J112 Extended Converage

Pendent

For Construction

0005 Tube Eddyflow Grooved For Construction

0006 Tube Eddythread Threaded For Construction

0007 Class 300 ductile Iron

Threaded Fittings

For Construction

0008 Grooved Couplings and Fittings For Construction

0009 Couplets Welded Pipe Outlets For Construction

0010 Grooved Butterfly Valves For Construction

0011 Grooved Check Valves For Construction

0012 Commercial Riser Manifold For Construction

0013 115 Standard Duty Loop

Hanger

For Construction

0014 10" 120V Electric Bell For Construction

0015 12 Count Sprinkler Cabinet For Construction

0016 Water Pressure Gauge Kits For Construction

0017 Globe Valves For Construction

0021 Swing Check Valves For Construction

0018 Angle Valves For Construction

0019 Floor/Ceiling Plates For Construction

Prolog Manager Printed on: 12/17/2015 KCI_Integated Page 1



Contact Name Copies NotesCompany NameCc:

Remarks

Signature Signed Date



Affiliated Engineers, Inc. | 4742 N 24th Street, Suite 100 Phoenix, AZ 85016

Page 1 of 1

PROJECT: Banner Health - Health Center Tatum & Greenway15193-00

DATE SENT: 12/7/2015

SUBJECT: 001-0211313 BMG\HC 15-0001 Tatum & Greenway Health Center Fire System Product Info 11242015

SUBMITTAL ID: 211313-001-0

TYPE: Submittal TRANSMITTAL ID: 00031

ACTION: Reviewed Only/No Approval Action Required

VIA: Email

SPEC SECTION: 21 0000

FROM

NAME COMPANY EMAIL PHONE

Joe Sanchez Affiliated Engineers, Inc. [email protected] 602-429-5842

TO

NAME COMPANY EMAIL PHONE

Phoenix Submit [email protected]

REMARKS: Reviewed Only. No approval action required.- Joe Sanchez

DESCRIPTION OF CONTENTS

QTY DATED TITLE NUMBER SCALE SIZE

1 11/24/2015 001-211313 Fire System Product Info.pdf

COPIES:

Zach Goldsworthy (Affiliated Engineers, Inc.) Jeff Cordell (Affiliated Engineers, Inc.) Cecilia Diaz (Affiliated Engineers, Inc.)



Kitchell Contractors Inc. of AZBanner Tatum/Grnway - Const Project # 6060B

4720 E GREEWAY ROAD

PHOENIX, AZ 85032

Tel: Fax:

Date: 11/24/2015 Reference Number: 0014

Transmitted To: Transmitted By: Matt KirchSteve Goodman

DWL ARCHITECTS + PLANNERS Kitchell Contractors Inc. of AZ

2333 NORTH CENTRAL AVE

PHOENIX, AZ 85004

1707 E Highland, Suite 100

Phoenix, AZ 85016

Tel: (602) 222-5300

Fax: (602) 263-8593

Submittal Package No Description Due Date Package ActionQty

For Approval12/8/2015Fire System Equipment and Material0001 - 21 13 13 - 019

Transmitted For Delivered Via Tracking Number

E-mailApproval

Notes Item ActionItems DescriptionQty

0001 F1FR56 Upright For Approval

0002 F1FR56 Recessed Pendent For Approval

0003 F1FR56 Horizontal Sidewall For Approval

0004 J112 Extended Converage

Pendent

For Approval

0005 Tube Eddyflow Grooved For Approval

0006 Tube Eddythread Threaded For Approval

0007 Class 300 ductile Iron

Threaded Fittings

For Approval

0008 Grooved Couplings and Fittings For Approval

0009 Couplets Welded Pipe Outlets For Approval

0010 Grooved Butterfly Valves For Approval

0011 Grooved Check Valves For Approval

0012 Commercial Riser Manifold For Approval

0013 115 Standard Duty Loop

Hanger

For Approval

0014 10" 120V Electric Bell For Approval

0015 12 Count Sprinkler Cabinet For Approval

0016 Water Pressure Gauge Kits For Approval

0017 Globe Valves For Approval

0021 Swing Check Valves For Approval

0018 Angle Valves For Approval

0019 Floor/Ceiling Plates For Approval


mkirch

Released

mkirch

Text Box

6116 A

mkirch

Text Box

0001-211313-0

mkirch

Group

Fire System Product Info

mkirch

Text Box

X

mkirch

Text Box

Matt Kirch

mkirch

Text Box

mkirch

Text Box

mkirch

Rectangle

mkirch

Text Box

11/24/15



Contact Name Copies NotesCompany NameCc:

Remarks

Signature Signed Date


EQUIPMENT & MATERIAL

SUBMITTAL

AS PROVIDED TO: KITCHELL CONTRACTORS, INC.

KITCHELL CONTRACTORS, INC. 1707 EAST HIGHLAND

PHOENIX, AZ 85016

FOR:

BHC – GREENWAY & TATUM 4720 EAST GREENWAY ROAD

PHOENIX, AZ 85032

AERO Job ###### Aero Automatic Sprinkler Co. 21605 North Central Ave. Phoenix, AZ 85024 623-580-7800 623-434-3420 fax

AS PRESENTED BY:

NOVEMBER 24, 2015

NOTE: PRODUCT DATA SHEETS INCLUDED ARE FOR

MATERIALS AND DEVICES INTENDED FOR

INSTALLATION. SUBSTITUTIONS MAY BE MADE FOR

EQUIVALENT MATERIAL AND DEVICES (i.e. [OR EQUAL])

AT TIME OF PROCUREMENT. ALL MATERIAL AND

DEVICES PROVIDED SHALL BE IN ACCORDANCE WITH

PROJECT SPECIFICATIONS UNLESS A SUBSTITUTION HAS

BEEN APPROVED.

EQUIPMENT & MATERIAL SUBMITTAL

TABLE OF CONTENTS

SECTION 1 SPRINKLERS

SECTION 2 PIPE

SECTION 3 FITTINGS

SECTION 4 VALVES

SECTION 5 HANGERS

SECTION 6 ELECTRICAL

SECTION 7 MISCELLANEOUS

SECTION 8 (NOT USED)

NOTE: PRODUCT DATA SHEETS INCLUDED ARE FOR MATERIALS AND DEVICES INTENDED FOR INSTALLATION. SUBSTITUTIONS MAY BE MADE FOR EQUIVALENT MATERIAL AND DEVICES (i.e. [OR EQUAL]) AT TIME OF PROCUREMENT. ALL MATERIAL AND DEVICES PROVIDED SHALL BE IN ACCORDANCE WITH PROJECT SPECIFICATIONS UNLESS A SUBSTITUTION HAS BEEN APPROVED.

Aero Automatic Sprinkler Company

21605 North Central Ave.

Phoenix, AZ 85024

623-580-7800 623-434-3420 fax

SECTION 1

SPRINKLER HEADS

RELIABLE F1FR56 UPRIGHT (BRASS) [OR EQUAL]

RELIABLE F1FR56 RECESSED PENDENT (CHROME W/CHROME

ESCUTCHEON) [OR EQUAL]

RELIABLE F1FR56 HORIZONTAL SIDEWALL (BRASS) [OR EQUAL]

RELIABLE J112 EXTENDED COVERAGE PENDENT (CHROME W/ CHROME

ESCUTCHEON) [OR EQUAL]

Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523

Model F1FR SeriesQuick ResponseGlass Bulb Sprinklers

Bulletin 014 R

ev. N

Bulletin 014 Rev. N

Model F1FR56 Sprinkler TypesStandard Spray UprightStandard Spray PendentConventional Upright/PendentVertical SidewallHorizontal Sidewall

Model F1FR56 Recessed Sprinkler TypesStandard Spray PendentHorizontal Sidewall

Model F1FR56 Concealed Sprinkler TypesStandard Spray Pendent

Model F1FR42, F1FRXLH & F1FR28 Sprinkler Types

Standard Spray UprightStandard Spray Pendent

Model F1FR40 Sprinkler TypesStandard Spray Pendent

Model F1FR42, F1FR40, F1FRXLH & F1FR28 Recessed Sprinkler Types

Standard Spray PendentModel F1FR56LL & F1FR42LL NSF Certifi ed Low Lead Sprinkler Types

Standard Spray Pendent with less than 0.25% Lead Content

Listing & ApprovalsThe following organizations provide Listings or Approvals for various Model F1FR series sprinklers. See the Design and Installation table in this Bulletin for information on specific listings and approvals applicable to each sprin-kler.

1. Underwriters Laboratories Inc. and Certified for Canada (cULus).

2. FM Approvals (FM)3. Loss Prevention Certification Board (LPCB)4. Vertrauen durch Sicherheit (VdS)5. NSF Certified to NSF/ANSi Standard 61 Annex G

(NSF)6. EC Certificate: 0786-CPD-40239 (RA1414), 0786-

CPD-40251 (RA1425), 0786-CPD-40252 (RA1475) (EC)

UL Listing CategorySprinklers, Automatic & Open (VNIV)Quick Response Sprinkler

Pendent Conventional

RecessedPendent/F1/F2

Upright

Vertical Sidewall Horizontal Sidewall

RecessedHorizontal Sidewall

RecessedPendent/FP

ConcealedPendent

XLH Upright XLH Pendent XLH RecessedPendent F1/F2

XLH RecessedPendent FP

Product DescriptionReliable Model F1FR series sprinklers

are quick-response automatic sprin-klers with a glass bulb thermal element. Model F1FR series sprinklers are Stan-dard Spray sprinklers, with the excep-tion of the Model F1FR56 Conventional sprinkler which is an Old-style/Conven-tional sprinkler.

The Model F1FR Series automatic sprinklers utilize a 3.0 mm frangible glass bulb. These sprinklers have demonstrat-ed response times in laboratory tests which are five to ten times faster than standard response sprinklers. This quick response enables the Model F1FR Series sprinklers to apply water to a fire faster than standard-response sprinklers of the same temperature rating.

The glass bulb consists of an accurately controlled amount of special fluid hermetically sealed inside a precisely man-ufactured glass capsule. This glass bulb is specially con-structed to provide fast thermal response.

2.

At normal temperatures, the glass bulb contains the fluid in both the liquid and vapor phases. The vapor phase can be seen as a small bubble. As heat is applied, the liquid expands, forcing the bubble smaller and smaller as the liq-uid pressure increases. Continued heating forces the liquid to push out against the bulb, causing the glass to shatter, opening the waterway and allowing the deflector to distrib-ute the discharging water.

Model F1FR Series sprinklers provide a wide range of op-tions where quick-response, glass bulb sprinklers are used:• Pendent, recessed pendent, upright, horizontal side-

wall, and vertical sidewall defl ectors• K-factors of 2.8 (40 metric), 4.0 (57 metric), 4.2 (60

metric), and 5.6 (80 metric)• Flush, recessed, and concealed installationsSee the Design and Installation Information table in this

Bulletin for information on the approvals and availability of specific Model F1FR series sprinkler configurations.

Model F1FR Recessed Pendent and Recessed Horizon-tal Sidewall sprinklers are required to be used with Reliable Model F1, F2, or FP recessed escutcheons. See the Re-cessed Escutcheon Data table in this Bulletin for listing and approval information with each specific Model F1FR series sprinkler. Model F1 and F2 recessed escutcheons, shown in Fig. 1 and 3, are a friction fit assembly allowing for 3/4-inch (19mm) and 1/2-inch (12.7mm) of adjustment, respectively. Model FP recessed escutcheons, shown in Fig. 2, provide a 1/2-inch (12.7mm) threaded adjustment.

Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers are required to be used with Model CCP cover plates. A standard profile Model CCP cov-er plate is available that provides up to 1/2-inch (12.7mm) of cover plate adjustment. In addition, a low profile Model CCP cover plate is also available that provides up to 5/16-inch (8.0mm) of cover plate adjustment. See the Design and In-stallation Information and Listed and Approved Temperature Ratings tables in this Bulletin for further information on ap-proved cover plate options.Application

Model F1FR Series sprinklers are intended for use in accordance with NFPA 13, FM Property Loss Prevention Data Sheets, and the requirements of the Authority Hav-ing Jurisdiction. Care must be exercised that the k-factor, temperature rating, deflector style, and sprinkler type are in accordance with the requirements of the applicable design and installation standards. In addition, Model F1FR Series sprinklers must be used in accordance with their listings and approvals, as well as the information provided in this Bulletin.Installation

Glass bulb sprinklers have orange bulb protectors or pro-tective caps to minimize bulb damage during shipping, han-dling and installation. Reliable sprinkler installation wrench-es are designed to install sprinklers with bulb protectors in place. Remove the bulb protector at the time when the sprin-kler system is placed in service for fire protection. Removal of the bulb protector before this time may leave the bulb vul-nerable to damage. Remove bulb protectors by undoing the clasp by hand. Do not use tools to remove bulb protectors.

Model F1FR Series sprinklers must be installed with the Reliable sprinkler installation wrench identified in the Design and Installation Information table in this Bulletin. Any other wrench may damage the sprinkler. A leak tight sprinkler joint can be obtained with a torque of 8 to 18 lb-ft (11 to 24 N-m). Do not tighten sprinklers over the maximum recommended installation torque. Exceeding the maximum recommended installation torque may cause leakage or impairment of the sprinkler.Recessed Sprinklers

Model F1FR Series Recessed sprinklers are to be installed as shown in Fig. 1, Fig. 2, or Fig. 3, as applicable to the spe-cific model being installed. The Recessed Escutcheon Data table in the Bulletin identifies the only recessed escutcheons that are permitted to be used with each Model F1FR Series Recessed sprinkler. The use of any other recessed escutch-eon will void all approvals and negate all warranties.Concealed Sprinklers

Model F1FR Series Concealed Pendent sprinklers are to be installed as shown in Fig. 4 or Fig. 5, as applicable to the selected cover plate. Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers have a factory-installed Model CCP cup. A protective cap is in-stalled at the factory that should remain on the sprinkler until the sprinkler is installed and should then be reinstalled on the sprinkler until the cover plate is installed. The concealed sprinkler assemblies are completed by the installation of a Model CCP push-on/thread-off cover plate assembly. The cover plate and sprinkler cup assemblies are joined using a cover plate skirt with flexible tabs for threaded engage-ment. A choice of two Model CCP cover plate assemblies provides either 1/2-inch (13mm) or 5/8-inch (8mm) of cover adjustment. Do not install Model F1FR Series Concealed Pendent sprinklers in ceilings which have positive pressure in the space above.

Model F1FR Series Concealed Pendent sprinklers require a 2-5/8-inch (67mm) diameter hole to be cut in the ceiling. The Model RC1 wrench is used to engage the sprinkler wrenching surfaces and to install the sprinkler in the fitting. Remove the protective cap to install the sprinkler, then reinstall the protective cap until the cover plate is installed. When inserting or remov-ing the wrench from the sprinkler/cup assembly, care should be taken to prevent damage to the sprinkler. Do not wrench any other part of the sprinkler/cup assembly. Installation is com-pleted by removing the protective cap from the sprinkler and pushing the cover plate onto the cup. Final adjustment is made by hand turning the cover plate until the skirt flange makes full contact with the ceiling. Cover plate removal requires turning the cover plate in the counter clockwise direction. After installation, inspect all sprinklers to ensure that there is a gap between the cover plate and ceiling and that the four cup slots are open and free from any air flow impediment to the space above.

Concealed cover plate/cup assemblies are listed only for use with specific sprinklers. The use of any concealed cover plate/cup assembly other than the Reliable Model CCP with Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers or the use of the Model CCP Concealed cover plate assembly on any sprinkler with which it is not specifically listed my prevent good fire protection and will void all guarantees, warranties, listings and approvals.

3.

Design and Installation Information

ModelNominalK-factor

NominalOrifi ce

DiameterDefl ector/

Orientation

Nominal Sprinkler

HeightInstallation

WrenchSIN

Listingsand

Approvals

Approval Notes

US Metric inches mm inches mm

F1FR28 2.8 40 3/8 10

Pendent 2.25 57 D RA1411 cULus 2

Recessed Pendent 2.25 57 GFR2 RA1411 cULus 2

Upright 2.25 57 D RA1421 cULus 1,2

F1FR40 4.0 57 3/8 10Pendent 2.25 57 D RA1418 VdS

Recessed Pendent 2.25 57 GFR2 RA1418 VdS

F1FR42 4.2 60 7/16 10




F1FR42LL 4.2 60 7/16 10Pendent 2.25 57 D RA1410 cULus, NSF

Recessed Pendent 2.25 57 GFR2 RA1410 cULus, NSF

F1FRXLH(F1FR42

with Pintle)4.2 60 7/16 10




F1FR56 5.6 80 1/2 15

Pendent 2.25 57 D RA1414cULus, FM,

LPCB, VdS, EC1,2,3,4

Recessed Pendent 2.25 57 GFR2 RA1414cULus, FM,


Concealed Pendent 2.25 57 RC1 RA1414 cULus,VdS,EC 5,6

Upright 2.25 57 D RA1425cULus, FM,


"Conventional(Pendent or Upright)"

2.25 57 D RA1475 LPCB, VdS, EC 4

F1FR56LL 5.6 80 1/2 15

Pendent 2.25 57 D RA1415 cULus, NSF 1

Recessed Pendent 2.25 57 GFR2 RA1415 cULus, NSF

Concealed Pendent 2.25 57 RC1 RA1414 cULus, NSF 6

F1FR56 5.6 80 1/2 15Horizontal Sidewall 2.63 67 D RA1435 cULus, FM 1,2,3,7

Recessed Horizontal Sidewall

2.63 67 GFR2 RA1435 cULus, FM 8

F1FR56 5.6 80 1/2 15Vertical Sidewall

(Pendent or Upright)2.25 57 D RA1485

cULus, FM, LPCB

1,2,3,9

(1) cULus Listed Corrosion Resistant sprinkler when ordered with available Polyester coating. (2) cULus Listed Corrosion Resistant sprinkler when ordered with available Electroless Nickel PTFE plating.(3) Available with FM approved Polyester coating in black or white.(4) Available with LPCB and VdS approved Polyester coating.(5) VdS and EC approvals of the F1FR56 Concealed Pendent sprinkler are for 155°F (68°C) temperature rated sprinklers only. VdS approved sprin-

klers must use Norbulb brand glass bulbs with the 1/2-inch (12.7mm) adjustment Model CCP cover plate only. (6) Model F1FR56 Concealed Pendent and Model F1FR56LL Concealed Pendent sprinklers must be used with Reliable Model CCP cover plates,

available as either standard depth with 1/2-inch (12.7mm) of adjustment or low profile with 5/16-inch (8.0 mm) of adjustment.(7) cULus Listing of the F1FR56 Horizontal Sidewall sprinkler is for Light and Ordinary Hazard occupancies only. FM Approval of the F1FR56 Hori-

zontal Sidewall sprinkler is for Light Hazard occupancies only.(8) cULus Listing and FM Approval of the F1FR56 Recessed Horizontal Sidewall sprinkler is for Light Hazard occupancies only. (9) The F1FR56 Vertical Sidewall sprinkler is listed and approved for use only in Light Hazard occupancies. Minimum to maximum deflector to ceil-

ing distance shall be 4 inches to 12 inches (102mm to 305mm). LPCB approval of the F1FR56 Vertical Sidewall sprinkler is for installation in the Pendent position only.

Technical Data:Sensitivity: Quick-responseThread Size: 1/2-inch NPT standard; ISO 7-R1/2 optionalMaximum Working Pressure: 175 psi (12 bar) - 100% Factory tested hydrostatically to 500 psi (34.5 bar)SIN RA1425, RA1414 & RA1435 cULus listed for 250 psi (17 bar)

4.

Listed and Approved Temperature Ratings

ModelDefl ector/

Orientation

Ordinary Temp.Classifi cation

100°F (38°C) Max. Ambient Temp.

Intermediate Temp.Classifi cation

150°F (65°C) Max. Ambient Temp.

High Temp.Classifi cation

225°F (107°C) Max.Ambient Temp.

135°F (57°C) Temp. Rating





Orange Bulb Red Bulb Yellow Bulb Green Bulb Blue Bulb

F1FR28Pendent cULus

Recessed Pendent cULus --Upright cULus

F1FR40Pendent VdS

Recessed Pendent VdS --

F1FR42Pendent cULus


F1FR42LLPendent -- cULus, NSF --

Recessed Pendent -- cULus, NSF --

F1FRXLHPendent cULus


F1FR56

Pendent cULus, FM, LPCB, VdS, ECRecessed Pendent cULus, FM, LPCB, VdS, EC --

Concealed Pendent* cULus cULus,VdS,EC cULus --Upright cULus, FM, LPCB, VdS, EC

“Conventional(Pendent or Upright)”

LPCB, VdS, EC

F1FR56LLPendent -- cULus, NSF --

Recessed Pendent -- cULus, NSF --Concealed Pendent* -- cULus, NSF --

F1FR56Horizontal Sidewall cULus, FM

Recessed Horizontal Sidewall

cULus, FM --

F1FR56 Vertical Sidewall (Pen-dent or Upright)

cULus, FM, LPCB

* Model F1FR56 Concealed Pendent and F1FR56LL Concealed Pendent sprinklers must be used with Reliable Model CCP cover plates. For Ordinary Temperature Classification sprinklers use a 135°F (57°C) temperature rated cover plate. For Intermediate Temperature Classification sprinklers use a 165°F (74°C) temperature rated cover plate.

Recessed Escutcheon Data

ModelDefl ector/

Orientation

Listed and Approved Recessed Escutcheons

SINModel F1

(Fig. 1 & 3)3/4-inch (19mm)

adjustment

Model F2(Fig. 1 & 3)

1/2-inch (12.7mm) adjustment

Model FP(Fig. 2)

1/2-inch (12.7mm) adjustment

F1FR28 Recessed Pendent cULus cULus cULus RA1411F1FR40 Recessed Pendent VdS VdS VdS RA1418F1FR42 Recessed Pendent cULus cULus cULus RA1413

F1FR42LL Recessed Pendent cULus, NSF cULus, NSF cULus, NSF RA1410F1FR42XLH Recessed Pendent cULus cULus cULus RA1413

F1FR56 Recessed PendentcULus, LPCB, VdS,

ECcULus, FM, LPCB,

VdS, ECcULus, VdS, EC RA1414

F1FR56LL Recessed Pendent cULus, NSF cULus, NSF cULus, NSF RA1415F1FR56 Recessed Horizontal Sidewall cULus cULus, FM cULus RA1435

5.

Fig. 1Model F1FR56, F1FR56LL, F1FR42, F1FR40, F1FR42LL, F1FRXLH & F1FR28

Recessed Pendent sprinkler with Model F1 or F2 escutcheon

Fig. 2Model F1FR56, F1FR56LL, F1FR42, F1FR40, F1FR42LL, F1FRXLH & F1FR28

Recessed Pendent sprinkler with Model FP escutcheon

6.

Fig. 3Model F1FR56 Recessed Horizontal Sidewall sprinkler with Model F1 or F2 escutcheon

Fig. 4Model F1FR56/F1FR56LL Concealed Pendent sprinkler with standard depth

1/2-inch (12.7mm) adjustment - Model CCP cover plate

7.

Fig. 5 - Model F1FR56/F1FR56LL Concealed Pendent sprinkler with low profile5/16-inch (8.0mm) adjustment - Model CCP cover plate

Maintenance The Model F1FR Series sprinklers should be inspected and

the sprinkler system maintained in accordance with NFPA 25. Do not clean sprinklers with soap and water, ammonia or any other cleaning fluids. Remove dust by using a soft brush or gentle vacuuming. Replace any sprinkler which has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be maintained to allow quick replacement of damaged or operated sprinklers. Finishes (1)

Standard FinishesSprinkler Escutcheon Cover plate(1)

Bronze Brass ChromeChrome Plated Chrome WhitePolyester PlatedCoated (4)(5)(6) White Painted

Special Application FinishesSprinkler Escutcheon Cover plate(1)

Electroless Nickel PTFE(7)

Electroless Nickel PTFE

Bright Brass

Bright Brass(3) Bright Brass Black PlatingBlack Plated Black Plated Black PaintBlack Paint(2)(6) Black Paint Off WhiteOff White(2)(6) Off White Satin ChromeChrome Dull Chrome Dull

(1) Other finishes and colors are available on special order. Consult the factory for details. Custom color painted sprinklers may not retain their UL Corrosion resistance listing. Coverplate custom paint is semi-gloss, unless specified otherwise.

(2) cULus Listed only.(3) 200°F (93°C) maximum.(4) cULus listed “corrosion resistance” applies to SIN Numbers RA1435

(HSW), RA1485(VSW), RA1425 (Upright), RA1414 (Pendent) and RA1415 (Pendent) in standard black or white. Corrosion resistance in other polyester colors is available upon request.

(5) FM Approvals finish as “Polyester coated” applies to SIN Number RA1414, RA1435 and RA1425 in standard black or white.(6) LPCB and VdS Approved finish applies only to RA1425, RA1414, RA1418

(VdS) and RA1475.(7) cULus listed Corrosion Resistant

Material DataFrame: DZR Brass, QM Brass, or Low Lead Brass

Defl ector: CDA Alloy 220, 260, or 510

Load Screw\Pintle: CDA Alloy 360 or 544

Cup: CDA Alloy 651 or 693

Washer: Nickel Alloy 440 or 360, coated with PTFE Adhesive Tape

Bulb: Glass

Ordering Information Specify: 1. Sprinkler Model: [F1FR28][F1FR40][F1FR42]

[F1FR42LL][F1FRXLH][F1FR56][F1FR56LL]2. Sprinkler Deflector/Orientation: [Pendent][Recessed

Pendent][Upright][Conventional][Horizontal Sidewall][Recessed Horizontal Sidewall][Vertical Sidewall]

3. Sprinkler threads: [1/2-inch NPT][ISO 7-R1/2]4. Sprinkler Temperature Rating: [135°F (57°C)][155°F

(68°C)][175°F (79°C)][200°F (93°C)][286°F (141°C)]5. Sprinkler Finish 6. Escutcheon Model: [F1][F2][FP]7. Escutcheon Finish (where applicable)8. Cover plate Model: [standard profile CCP 1/2-inch

(12.7mm) adjustment][low profile CCP 5/16-inch (8.0mm) adjustment]

9. Cover plate Temperature Rating: [135°F (57°C) for use with Ordinary Temperature sprinklers][165°F (74°C) for use with Intermediate Temperature sprinklers]

10. Cover plate Finish

Note: When Model F1FR Series Recessed sprinklers are ordered, the sprinklers and escutcheons are packaged separately.

Reliable Automatic Sprinkler Co., Inc.(800) 431-1588 Sales Offices(800) 848-6051 Sales Fax(914) 829-2042 Corporate Officeswww.reliablesprinkler.com Internet Address

Manufactured byRecycled

Paper

Revision lines indicate updated or new data.

EG. Printed in U.S.A. 12 /15 P/N 9999970300

The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries.

• Automatic sprinklers

• Flush automatic sprinklers

• Recessed automatic sprinklers

• Concealed automatic sprinklers

• Adjustable automatic sprinklers

• Dry automatic sprinklers

• Intermediate level sprinklers

• Open sprinklers

• Spray nozzles

• Alarm valves

• Retarding chambers

• Dry pipe valves

• Accelerators for dry pipe valves

• Mechanical sprinkler alarms

• Electrical sprinkler alarm switches

• Water flow detectors

• Deluge valves

• Detector check valves

• Check valves

• Electrical system

• Sprinkler emergency cabinets

• Sprinkler wrenches

• Sprinkler escutcheons and guards

• Inspectors test connections

• Sight drains

• Ball drips and drum drips

• Control valve seals

• Air maintenance devices

• Air compressors

• Pressure gauges

• Identification signs

• Fire department connection

Reliable offers a wide selection of sprinkler components. Following are some of the many precision-made Reliable products that guard life and property from fire around the clock.

Reliable...For Complete Protection

The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523

Bulletin 172 R

ev. FBulletin 172 Rev. F

Model JL112 & J112 - Pendent ECLH - Extended Coverage Light HazardECOH - Extended Coverage Ordinary HazardECOH - Extended Coverage OrdinaryHazard - Quick Response

Model JL112 & J112 ECLH/ECOHPendent & Recessed Pendent(SIN R7216 – Link and RA7216 – Bulb)

• Quick Response for Light Hazard(16’ x 16’ (4.9m x 4.9m), 18’ x 18’ (5.5m x 5.5m) and 20’ x 20’ (6.1m x 6.1m) spacing)

• Quick Response for Ordinary Hazard(12’ x 12’ (3.7m x 3.7m) and 14’ x 14’ (4.3m x 4.3m) spacing)

• Standard Response for Ordinary Hazard(16’ x 16’ (4.9m x 4.9m), 18’ x 18’ (5.5m x 5.5m) and 20’ x 20’ (6.1m x 6.1m) spacing)

Features1. Extended Coverage Ordinary Hazard and Light Hazard

protection to 400 ft2 (37.2 m2) per sprinkler.2. Nominal K = 11.2 (160).3. Available in Pendent or Recessed Pendent styles.4. Recessed pendent version provides ¾” (19mm) adjust-

ment to flush pendent position (see adjustment table).5. Available in brass, chrome, polyester coated

and Electroless Nickel PTFE (Teflon®)* plated6. For applications as per NFPA 13.

Approvals Organizations1. Underwriters Laboratories, Inc. (UL)2. Underwriters Laboratories of Canada (cULus)

UL Listing CategorySprinklers, Automatic and Open Extended Coverage Sprin-

klers-Ordinary Hazard Occupancy UL Guide Number – VNIV.The Reliable Model JL112 and J112 sprinkler are Extended

Coverage Sprinklers for use in both Light and Ordinary Hazard 1 and 2 occupancies with a coverage area of up to 400 square feet (37.2m2) per sprinkler.

For all light hazard applications it is a Quick Response sprin-kler. For ordinary hazard applications, it is a Standard Re-sponse sprinkler when the spacing is 16’ x 16’ (4.9m x 4.9m) and larger. When the spacing is 12’ x 12’ (3.7m x 3.7m) or 14’ x 14’ (4.3m x 4.3m), the sprinkler is Quick Response for ordinary hazard applications.

The use of ECLH/ECOH sprinklers can provide lower instal-lation costs by requiring fewer sprinklers, less piping and re-duced labor.

ECLH/ECOH sprinklers are to be installed according to the design criteria shown in this bulletin, NFPA 13, and all other lo-cal codes and ordinances. Flows and pressures as shown on pages 2 and 3 of this bulletin, must be used for the appropriate spacing and for the designated hazard classifications.

Model JL112 Pendent(R7216) - Link

Model J112 Pendent(RA7216) - Bulb

This ECLH/ECOH sprinkler is available in various finishes, which includes a white polyester corrosion resistant finish.

ECLH/ECOH sprinklers are available in a pendent or an attractive recessed pendent type which provides up to ¾” (19mm) of escutcheon adjustment.

Design CriteriaReliable Model JL112 & J112 ECLH/ECOH sprinklers

shall only be used in systems designed and installed in accordance with NFPA 13 and all other local codes and ordinances. The following design criteria also apply:• Minimum sprinkler spacing is 8 ft (2.44m).• Sprinklers have a minimum flow requirement for each

spacing as shown in the Flow Requirements Table on the reverse side.

• Sprinklers are only to be used in systems hydraulically designed per NFPA 13.

• Deflector to commodity clearance shall be a minimum of 18 inches (457mm).

• ECOH sprinklers shall be installed in unobstructed construction as defined in NFPA 13.

• ECOH sprinklers which are installed above the bottom of a horizontal obstruction, shall have their deflectors located as shown in the Obstruction Table on page 3.

• Sprinklers can be installed under a sloping ceiling not exceeding 2 inches (50.8mm) of rise in 12 inches (304.5mm).

• Maximum working pressure is 175 psi (12.1 bar) at the sprinkler.

SIN RA7216 is Corrosion Resistant with White or Black Polyester Coating or Electroless Nickel PTFE (Tefl on®)* plating.

*DuPont Registered Trademark

2.

Sprinkler Model Specifi cations

Sprinkler Model TypeTemperature

Rating

Max.Ceiling Temp.

Maximum Sprinkler Spacing

ft (m)

Maximum Coverage

Areaft2 (m2)

THDSize

Approvals

°F °C °F °C

JL112 ECLH/ECOH- R7216 Link/Pendent 165212

74100

100150

3866

20 (6.1) 400 (37.2)¾”NPT(19mm)

1,2JL112 ECLH/ECOH- R7216 Link/Recessed

J112 ECLH/ECOH- RA7216 Bulb/Pendent 155200

6893

100150

3866

20 (6.1) 400 (37.2)J112 ECLH/ECOH- RA7216 Bulb/Recessed

Flow Requirements - Light Hazard - Quick Response

Spacingft (m)

Coverage Areaft2 (m2)

Flowgpm (lpm)

Pressurepsi (bar)

“K” Factor

US Metric

16 x 16 (4.9 x 4.9) 256 (23.8) 30 (113.6) 7.2 (0.5)

11.2 160.018 x 18 (5.5 x 5.5) 324 (30.1) 33 (124.9) 8.7 (0.6)

20 x 20 (6.1 x 6.1) 400 (37.2) 40 (151.4) 12.8 (0.9)

Flow Requirements - Ordinary Hazard - Standard Response

Spacingft (m)

Coverage Area

ft2 (m2)

Ordinary Hazard 1 Ordinary Hazard 2“K” Factor0.15 gpm/ft2 (6.1 L/min/m2)

Density0.20 gpm/ft2 (8.1 L/min/m2)

Density

Flow gpm (Lpm)

Pressurepsi (bar)

Flowgpm (lpm)

Pressurepsi (bar)

US Metric

16 x 16 (4.9 x 4.9) 256 (23.8) 39 (147.6) 12.1 (0.8) 51 (193.0) 20.7 (1.4)

11.2 160.018 x 18 (5.5 x 5.5) 324 (30.1) 49 (185.5) 19.1 (1.3) 65 (246.0) 33.7 (2.3)

20 x 20 (6.1 x 6.1) 400 (37.2) 60 (227.1) 28.7 (2.0) 80 (302.8) 51.0 (3.5)

Flow Requirements - Ordinary Hazard - Quick Response

Spacingft (m)

Coverage Area

ft2 (m2)

Ordinary Hazard 1 Ordinary Hazard 2“K” Factor0.15 gpm/ft2 (6.1 L/min/m2)

Density0.20 gpm/ft2 (8.1 L/min/m2)

Density

Flowgpm (Lpm)

Pressurepsi (bar)

Flowgpm (Lpm)

Pressurepsi (bar)

US Metric

14 x 14 (4.3 x 4.3) 196 (18.2)30 (113.6) 7.2 (0.5) 39 (147.6) 12.1 (0.8) 11.2 160.0

12 x 12 (3.7 x 3.7) 144 (13.4)

Recess Escutcheons

Minimum Flow Requirements For Earlier Editions of NFPA 13 - FOR REFERENCE ONLY

Spacingft (m)

Coverage Area

ft2 (m2)

NFPA13 - 1991 Requirements NFPA13 - 1989 Requirements “K” Factor

Ordinary Hazard 1 Ordinary Hazard 2 Ordinary Hazard 1 Ordinary Hazard 2 Ordinary Hazard 3

US Metric

0.15 gpm/ft2

(6.1 L/min/m2)Density

0.20 gpm/ft2


0.16 gpm/ft2


0.19 gpm/ft2


0.21 gpm/ft2


Flowgpm

(Lpm)

Pressurepsi

(bar)

Flowgpm

(Lpm)

Pressurepsi

(bar)

Flowgpm

(Lpm)

Pressurepsi

(bar)

Flowgpm

(Lpm)

Pressurepsi

(bar)

Flowgpm

(Lpm)

Pressurepsi (bar)

14 x 14(4.3 x 4.3)and less

196 (18.2)30.2

(114.3)7.0

(0.48)39.2

(148.3)11.9

(0.82)31.4

(118.8)7.6

(0.52)37.3

(141.2)10.7

(0.74)41.2

(155.9)13.0

(0.90)

11.4 164.4

16 x 16(4.9 x 4.9)

256 (23.8)38.4

(145.3)11.4

(0.79)51.2

(193.8)20.2

(1.39)41.0

(155.2)12.9

(0.89)48.7

(184.3)18.2

(1.26)53.8

(203.6)22.3

(1.54)

18 x 18(5.5 x 5.5)

324 (30.1)48.6

(184.0)18.2

(1.24)64.8

(258.9)32.3

(2.23)51.9

(196.4)20.7

(1.43)61.6

(233.2)29.2

(2.01)68.0

(257.4)35.7

(2.46)

20 x 20(6.1 x 6.1)

400 (37.2)60.0

(227.1)27.7

(1.91)80.0

(302.8)49.3

(3.40)64.0

(242.2)31.5

(2.17)76.0

(287.7)44.5

(3.07)84.0

(317.9)54.3

(3.75)

Model J1 Sprinkler Wrench

Use Model J1 Wrench for JL112 & J112 ECLH/ECOH Pendent Sprinkler Removal

and Installation

Model RJ Sprinkler Wrench

Use Model RJ Wrench for JL112 & J112 ECLH/ECOH Recessed

Sprinkler Removal and Installation

F1/F2

3.

Recessed Pendent ECLH/ECOH Adjustments (1)

EscutcheonECLH ECOH

R7216 RA7216 R7216 RA7216

FP ¾ (19.0) ¾ (19.0) ¾ (19.0) ¾ (19.0)

F1 (2) (2) ¾ (19.0) ¾ (19.0)

F2 ½ (12.7) ½ (12.7) ½ (12.7) ½ (12.7)

(1) Adjustments in inches (mm).(2) Not listed by UL or cULus.

Finishes

Sprinkler Finishes

Sprinkler Escutcheon

BronzeChrome

White and Black Polyester Coated (2)

BrassChrome

White Painted

Special Application FinishesSprinkler Escutcheon

Electroless Nickel PTFE(Teflon®)*(1) (2) Electroless Nickel PTFE (Teflon®)*

(1) RA7216 Only 2) Corrosion Resistant

Ordering Information1. Sprinkler Model2. Temperature Rating3. Finish4. Escutcheon and finish (where applicable)

Corrosion Resistant

J112 ECLH/ECOH

Bulb

°F °C

155200

6893

FP

J1 Wrench RJ Wrench

*DuPont Registered Trademark

Installation Requirements for Under Concrete Tees - cULus

• The stems of the concrete tee construction must be spaced at less than 7.5 feet (2.3m) on center but more than 3 feet (0.9m) on center. The depth of the concrete tees must not exceed 30 inches (762mm). The maximum permitted concrete tee length is 32 feet (9.8m); however, where the concrete tee length exceeds 32 feet (9.8m), non-combustible baffles, equal in height to the depth of the tees, can be installed so that the longitudinal space between the tees does not exceed 32 feet (9.8m) in length.

• The sprinkler deflectors are to be located in a horizontal plane at or above 1 inch (25.4mm) below the bottom of the concrete tee stems.

• When the sprinkler deflectors are located higher than a horizontal plane 1 inch (25.4mm) beneath the bottom of the concrete tee stems, the obstruction to sprinkler discharge criteria requirements of NFPA13 for extended coverage upright sprinkler applies.

Location of Defl ector to Horizontal Obstruction

Distance from Sprinkler to Side of Obstruction

Maximum Allowable Distance Defl ector Above Bottom of

Obstruction

Less than 1’.................................................................... 0”(Less than 0.305m ................................................... 0mm)1’ to less than 1’ - 6”....................................................... 0”(0.305m to less than 0.305m - 152.4mm.................. 0mm)1’ - 6” to less than 2’....................................................... 1”(0.305m - 152.4mm to less than 0.61m............... 25.4mm)2’ to less than 2’ - 6”....................................................... 1”(0.61m to less than 061m - 152.4mm.................. 25.4mm)2’ - 6” to less than 3’....................................................... 1”(0.61m - 152.4mm to less than 0.915m............... 25.4mm)3’ to less than 3’ - 6”....................................................... 3”(0.915m to less than 0.915m - 152.4mm............. 76.2mm)3’ - 6” to less than 4’....................................................... 4”(0.915m - 152.4mm to less than 1.22m ............ 101.6mm)4’ to less than 4’ - 6”....................................................... 5”(1.22m to less than 1.22m - 152.4mm.................. 127mm)4’ - 6” to less than 5’ .......................................................7”(1.22m - 152.4mm to less than 1.525m ............ 177.8mm)5’ to less than 5’ - 6” ...................................................... 7”(1.525m to less than 1.525m - 152.4mm........... 177.8mm)5’ - 6” to less than 6’ ...................................................... 7”(1.525m - 152.4mm to less than 1.83m ............ 177.8mm)6’ to less than 6’ - 6”....................................................... 9”(1.83m to less than 1.83m - 152.4mm............... 228.6mm)6’ - 6” to less than 7’ .................................................... 11”(1.83m - 152.4mm to less than 2.135m ............ 279.4mm)7’ and greater .............................................................. 14”(2.135m and greater ......................................... 355.6mm)

Solder Link Bulb

Classifi cation °F °C Link Color Classifi cation °F °C Bulb Color

OrdinaryIntermediate

165212

74100

Black*White

OrdinaryIntermediate

155200

6893

RedGreen

* 165°F chrome plated and white painted sprinklers will contain a white painted solder link.

Fig. 1 - F1 Escutcheon

The Reliable Automatic Sprinkler Co., Inc.(800) 431-1588 Sales Offices(800) 848-6051 Sales Fax(914) 829-2042 Corporate Officeswww.reliablesprinkler.com Internet Address


Paper


EG. Printed in U.S.A. 01/14


PN 9999970310

Section 2

PIPE

BULL MOOSE TUBE EDDYFLOW (GROOVED) [OR EQUAL]

BULL MOOSE TUBE EDDYTHREAD (THREADED) [OR EQUAL]

Eddy Flow

The Cost Effective Replacement for Schedule 10 Realizing the growing need of fire protection systems in commercial and residential construction, Bull Moose Tube has added Eddy Flow to its comprehensive line of sprinkler pipe products. Eddy Flow is a specially engineered replacement for schedule 10, offering better flow characteristics while providing design flexibility. This product is FM approved, as well as UL listed (for U.S. and Canada) for roll grooving and welding for use in fire protection

systems with a working pressure of 300 psi or less. Please check with appropriate sources for up-to-date listings and approval information. As an added benefit, it is more economical to use than schedule 10 due to reduced delivery costs and ease of handling. Furthermore, Eddy Flow’s larger ID provides an opportunity for downsizing and further cost savings.

COMPARISON

INSIDE DIAMETER C.R.R.*

Nominal Pipe Size (in)

O.D. (in) Eddy Flow

(in) Schedule 10

(in) Schedule 40

(in) Eddy Flow Schedule 40

1 1/4 1.660 1.530 1.442 1.380 1.98 1.00 1 1/2 1.900 1.728 1.682 1.610 3.44 1.00 2 2.375 2.203 2.157 2.067 2.78 1.00 2 1/2 2.875 2.705 2.635 2.469 1.66 1.00 3 3.500 3.334 3.260 3.068 1.00 1.00 4 4.500 4.310 4.260 4.026 1.00 1.00 * Corrosion Resistance Ratio

BENEFITS • Dual Certified to ASTM A135 and A795. • FM Approved for roll grooved, and welded, and plain-end application in wet systems. • UL Listed (for U.S. and Canada) for joining by welding or by listed rubber gasketed fittings for use in wet, dry,

preaction, and deluge type sprinkler systems. • UL Listed (for US and Canada) and FM Approved for use with Victaulic® FIT® Fittings in plain end applications. • Lightweight - saves shipping costs, and offers easier handling. • Can be used with roll grooved couplings or welded outlets for pressures up to 300 psi. • Floor stock available in various lengths produced in Casa Grande (AZ), Gerald (MO), and Masury (OH). Also can be

ordered in custom lengths.. • Can be used for wet and dry* systems.

* Eddy Flow can be hot dipped galvanized to meet FM’s requirement for dry systems.

PIPE PREPARATION For proper operation, all pipe surfaces should be cleaned prior to installation. In order to provide a leak-tight seat for the gasket, pipe surfaces should be free from indentations and projections from the end of the pipe to the groove. All loose paint, scale, dirt, chips, grease, and rust must be removed prior to installation. Failure to take these important steps may result in improper coupling assembly, causing leakage. Also, check the manufacturer’s instructions for the specific fitting used.

A company

1819 Clarkson Road Chesterfield, MO 63017 (800) 325-4467 FAX: (636) 537-2645 www.bullmoosetube.com e-mail:[email protected]

For additional information, contact your salesperson today at (800) 325-4467 or (636) 537-2600 in the USA, or from Canada call (800) 882-4666

All information contained herein is accurate as known at the time of publication. Bull Moose Tube reserves the right to change product specifications without notice and without incurring obligation. 8/08

Eddythread 40

A Lightweight Schedule 40 Replacement Pipe That Has a Corrosion Resistance Ratio of 1.0

Bull Moose Tube Company has been making pipe for a long time and is recognized as a producer of quality pipe products. Eddythread 40 is designed with the same thoroughness as our other fine pipe products and now our customers have an option to buy a carefully designed replacement for Schedule 40 that:

• Has a Corrosion Resistance Ratio of 1.0 • Has a Pressure Rating of 300 psi • Is Lighter Weight Than Schedule 40 • Is Approved by Factory Mutual and Listed by Underwriters Laboratories • Is Produced in Accordance to ASTM A-135 and A-795 • Can be Used With Standard Schedule 40 Threaded Fittings,

Couplings and Valves • Is Produced From Steel With Excellent Properties of

Strength and Threadability • Can be Used in Wet, Dry, Preaction, and Deluge Type Sprinkler Systems* • Offers Lower Freight Costs

EDDYTHREAD 40 SPECIFICATIONS NOMINAL PIPE SIZE (in) WEIGHT (lbs/ft) I.D. (in) BUNDLE SIZE

1 1.461 1.083 70

1 1/4 2.070 1.418 51

1 1/2 2.547 1.654 44

2 3.308 2.123 30

CORROSION RESISTANCE RATIOS

NOMINAL PIPE SIZE (in) SCHEDULE 40 EDDYTHREAD 40

1 1.00 1.00

1 1/4 1.00 1.00

1 1/2 1.00 1.00

2 1.00 1.00

* Eddythread 40 can be hot dipped galvanized to meet FM's requirement for dry systems

A company

1819 Clarkson Road Chesterfield, MO 63017 (800) 325-4467 FAX: (636) 537-2645 www.bullmoosetube.com e-mail:[email protected]

For additional information, contact your salesperson today at (800) 325-4467 or (636) 537-2600 in the USA, or from Canada call (800) 882-4666

All information contained herein is accurate as known at the time of publication. Bull Moose Tube reserves the right to change product specifications without notice and without incurring obligation. 8/08

SECTION 3

FITTINGS

SCI CLASS 300 DUCTILE IRON THREADED FITTINGS [OR EQUAL]

SCI GROOVED COUPLINGS & FITTINGS [OR EQUAL]

SCI COOPLETS WELDED PIPE OUTLETS [OR EQUAL]

Ductile Iron Threaded Fittings

Ductile Iron Threaded Fittings

TemperatureDegrees F

Working Pressure, Nonshock psiG300# Class Threaded Fittings

-20 to 100 500150 500200 480250 460300 440350 420400 400450 380500 360550 340600 320650 300

Specifi cations

• branded ductile iron threaded fi ttings are UL Listed and FM Approved at 500 psi

• Rated to 300 WSP

• Ductile iron castings conform to ASTM A536

• Fitting dimensions conform to ASME B16.3

• Bushings and plugs conform to ASME B16.14

• Fittings are 100% air tested

• NPT threads on all fi ttings conform to ASME B1.20.1

• Independent lab verifi cation that fi ttings meet applicable chemical & physical properties

• Manufacturing facilities are ISO 9001:2008 and ISO 14001

SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com111

DUCTILE

A

A

A

A

A

A

AA

B

Sizein Part Number

Ain

Packing WeightlbInner Master

1/2 35E 3004 1.13 100 200 0.23/4 35E 3006 1.31 70 140 0.31 35E 3010 1.50 40 80 0.5

1-1/4 35E 3012 1.75 25 50 0.81-1/2 35E 3014 1.94 18 36 1.1

2 35E 3020 2.25 10 20 1.82-1/2 35E 3024 2.70 4 8 3.2

Sizein Part Number

Ain

Bin


3/4 x 1/2 35RE3006004 1.20 1.22 80 160 0.31 x 1/2 35RE3010004 1.26 1.36 70 140 0.41 x 3/4 35RE3010006 1.38 1.45 50 100 0.4

1-1/4 x 1/2 35RE3012004 1.34 1.53 35 70 0.51-1/4 x 3/4 35RE3012006 1.45 1.63 35 70 0.61-1/4 x 1 35RE3012010 1.58 1.67 30 60 0.7

1-1/2 x 1/2 35RE3014004 1.52 1.75 30 60 0.61-1/2 x 3/4 35RE3014006 1.52 1.75 25 50 0.71-1/2 x 1 35RE3014010 1.65 1.80 20 40 0.8

1-1/2 x 1-1/4 35RE3014012 1.82 1.88 18 36 1.02 x 1/2 35RE3020004 1.60 1.97 18 36 1.02 x 3/4 35RE3020006 1.60 1.97 18 36 1.02 x 1 35RE3020010 1.73 2.02 16 32 1.2

2 x 1-1/4 35RE3020012 1.90 2.10 12 24 1.32 x 1-1/2 35RE3020014 2.02 2.16 10 20 1.5

2-1/2 x 1-1/2 35RE3024014 2.16 2.51 6 12 2.22-1/2 x 2 35RE3024020 2.39 2.60 6 12 2.5

Sizein Part Number

Ain


1/2 35F 3004 0.88 150 300 0.23/4 35F 3006 0.98 80 160 0.31 35F 3010 1.13 40 80 0.5

1-1/4 35F 3012 1.29 25 50 0.71-1/2 35F 3014 1.44 20 40 1.0

2 35F 3020 1.69 10 20 1.62-1/2 35F 3024 1.95 4 8 2.7

Sizein Part Number

Ain


1/2 35T 3004 1.13 80 160 0.33/4 35T 3006 1.31 30 60 0.51 35T 3010 1.50 25 50 0.7

1-1/4 35T 3012 1.75 10 20 1.11-1/2 35T 3014 1.94 10 20 1.5

2 35T 3020 2.25 6 12 2.42-1/2 35T 3024 2.70 4 8 4.3

Fig. 35E 3 – 90° Elbow

Fig. 35RE3 – 90° Reducing Elbow

Fig. 35F 3 – 45° Elbow

Fig. 35T 3 – Tee

Ductile Iron Fittings - Class 300 UL/FM

SMITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX (323) 890-4456 • www.smithcooper.com 112

DUCTILE

A B

AB

C

C

Sizein Part Number

Ain

Bin

Cin


3/4 x 1/2 35RT3006004 1.20 1.20 1.22 60 120 0.41 x 1/2 35RT3010004 1.26 1.26 1.36 30 60 0.6

1 x 1/2 x 1 35RT3010004010 1.50 1.36 1.50 30 60 0.61 x 3/4 35RT3010006 1.38 1.38 1.45 25 50 0.6

1 x 3/4 x 3/4 35RT3010006006 1.38 1.31 1.45 35 70 0.61 x 3/4 x 1 35RT3010006010 1.50 1.45 1.50 25 50 0.71-1/4 x 1/2 35RT3012004 1.34 1.34 1.53 20 40 0.8

1-1/4 x 1/2 x 1-1/4 35RT3012004012 1.75 1.53 1.75 25 50 0.91-1/4 x 3/4 35RT3012006 1.45 1.45 1.62 15 30 0.9

1-1/4 x 3/4 x 1-1/4 35RT3012006012 1.75 1.62 1.75 20 40 1.01-1/4 x 1 35RT3012010 1.58 1.58 1.67 15 30 1.0

1-1/4 x 1 x 1/2 35RT3012010004 1.34 1.26 1.53 25 50 0.71-1/4 x 1 x 3/4 35RT3012010006 1.45 1.38 1.63 20 40 0.81-1/4 x 1 x 1 35RT3012010010 1.58 1.50 1.69 20 40 0.9

1-1/4 x 1 x 1-1/4 35RT3012010012 1.75 1.69 1.75 15 30 1.01-1/2 x 1/2 35RT3014004 1.41 1.41 1.66 16 32 1.0

1-1/2 x 1/2 x 1-1/4 35RT3014004012 1.81 1.56 1.88 24 48 1.11-1/2 x 1/2 x 1-1/2 35RT3014004014 1.94 1.66 1.94 12 24 1.2

1-1/2 x 3/4 35RT3014006 1.52 1.52 1.75 16 32 1.11-1/2 x 3/4 x 1-1/4 35RT3014006012 1.94 1.66 1.88 20 40 1.11-1/2 x 3/4 x 1-1/2 35RT3014006014 1.94 1.75 1.94 18 36 1.2

1-1/2 x 1 35RT3014010 1.65 1.65 1.80 12 24 1.21-1/2 x 1 x 1/2 35RT3014010004 1.44 1.25 1.69 20 40 0.81-1/2 x 1 x 3/4 35RT3014010006 1.50 1.44 1.75 16 32 0.91-1/2 x 1 x 1 35RT3014010010 1.65 1.50 1.80 16 32 1.0

1-1/2 x 1 x 1-1/4 35RT3014010012 1.82 1.67 1.88 12 24 1.21-1/2 x 1 x 1-1/2 35RT3014010014 1.94 1.80 1.94 12 24 1.3

1-1/2 x 1-1/4 35RT3014012 1.82 1.82 1.88 12 24 1.41-1/2 x 1-1/4 x 1/2 35RT3014012004 1.41 1.34 1.66 16 32 0.91-1/2 x 1-1/4 x 3/4 35RT3014012006 1.52 1.45 1.75 16 32 1.01-1/2 x 1-1/4 x 1 35RT3014012010 1.65 1.58 1.80 16 32 1.1

1-1/2 x 1-1/4 x 1-1/4 35RT3014012012 1.82 1.75 1.88 14 28 1.31-1/2 x 1-1/4 x 1-1/2 35RT3014012014 1.94 1.88 1.94 14 28 1.4

2 x 1/2 35RT3020004 1.49 1.49 1.88 10 20 1.52 x 3/4 35RT3020006 1.60 1.60 1.97 10 20 1.62 x 1 35RT3020010 1.73 1.73 2.02 8 16 1.7

2 x 1 x 2 35RT3020010020 2.25 2.02 2.25 8 16 1.92 x 1-1/4 35RT3020012 1.90 1.90 2.10 8 16 1.9

2 x 1-1/4 x 2 35RT3020012020 2.25 2.10 2.25 8 16 2.02 x 1-1/2 35RT3020014 2.02 2.02 2.16 8 16 2.1

2 x 1-1/2 x 1/2 35RT3020014004 1.49 1.41 1.88 10 20 1.32 x 1-1/2 x 3/4 35RT3020014006 1.60 1.52 1.97 10 20 1.42 x 1-1/2 x 1 35RT3020014010 1.73 1.65 2.02 8 16 1.5

2 x 1-1/2 x 1-1/4 35RT3020014012 1.90 1.82 2.10 8 16 1.72 x 1-1/2 x 1-1/2 35RT3020014014 2.02 1.94 2.16 8 16 1.8

Sizein Part Number

Ain

Bin

Cin


3/4 x 1 35BT3006010 1.45 1.45 1.37 30 60 0.61 x 1-1/4 35BT3010012 1.67 1.67 1.58 20 40 0.91 x 1-1/2 35BT3010014 1.80 1.80 1.65 15 30 1.0

1-1/4 x 1 x 1-1/2 35BT3012010014 1.88 1.80 1.82 15 30 1.21-1/4 x 1-1/2 35BT3012014 1.88 1.88 1.82 15 30 1.3

1-1/4 x 2 35BT3012020 2.10 2.10 1.90 10 20 1.61-1/2 x 1-1/4 x 2 35BT3014012020 2.16 2.10 2.02 10 20 1.8

1-1/2 x 2 35BT3014020 2.16 2.16 2.02 8 16 1.8

Fig. 35BT3 – Bull Head Tee

Fig. 35RT3 – Reducing Tee



DUCTILE

A

A

A

A

A

B

Sizein Part Number

Ain


1 35U 3010 2.19 20 40 1.01-1/4 35U 3012 2.50 15 30 1.21-1/2 35U 3014 2.62 10 20 1.7

2 35U 3020 3.12 6 12 2.4

Sizein Part Number

Ain


1/2 35CP3004 1.38 200 400 0.13/4 35CP3006 1.63 100 200 0.21 35CP3010 1.75 60 120 0.4

1-1/4 35CP3012 2.00 35 70 0.51-1/2 35CP3014 2.19 25 50 0.7

2 35CP3020 2.62 15 30 1.22-1/2 35CP3024 3.00 9 18 2.2

Sizein Part Number

Ain


1 x 1/2 35RC3010004 1.69 80 160 0.31 x 3/4 35RC3010006 1.69 60 120 0.4

1-1/4 x 3/4 35RC3012006 2.06 40 80 0.62 x 1 (not hex) 35RC3020010 2.81 20 40 1.0

Sizein Part Number

Ain


1 x 1/2 35HB3010004 1.06 180 360 0.21 x 3/4 35HB3010006 1.06 180 360 0.1

1-1/4 x 1 35HB3012010 1.19 90 180 0.21-1/2 x 1 35HB3014010 1.25 75 150 0.4

1-1/2 x 1-1/4 35HB3014012 1.25 75 150 0.32 x 1 35HB3020010 1.38 40 80 0.6

2 x 1-1/4 35HB3020012 1.38 40 80 0.62 x 1-1/2 35HB3020014 1.38 40 80 0.6

Sizein Part Number

Ain


1/2 35SP3004 0.94 600 1200 0.073/4 35SP3006 1.12 350 700 0.11 35SP3010 1.25 200 400 0.1

1-1/4 35SP3012 1.37 100 200 0.31-1/2 35SP3014 1.44 80 160 0.4

2 35SP3020 1.50 45 90 0.6

Fig. 35CP3 – Straight Coupling with Ribs

Fig. 35RC3 – Hex Reducing Coupling

Fig. 35HB3 – Hex Bushing

Fig. 35SP3 – Square Head Plug

Fig. 35U 3 – Union with Brass Seat



DUCTILE

A A

A

A

A

A

A

B BSizein Part Number

Ain

Bin


1-1/4 x 1 35RX3012010 1.67 1.58 15 30 1.21-1/2 x 1 35RX3014010 1.80 1.65 12 24 1.4

2 x 1 35RX3020010 2.02 1.73 8 16 2.0

Sizein Part Number

Ain


1 35X 3010 1.50 20 40 0.91-1/4 35X 3012 1.75 12 24 1.41-1/2 35X 3014 1.94 8 16 1.8

2 35X 3020 2.25 6 12 2.8

Sizein Part Number

Ain


1/2 35C 3004 0.87 300 600 0.13/4 35C 3006 0.97 200 400 0.11 35C 3010 1.16 110 220 0.2

1-1/4 35C 3012 1.28 70 140 0.41-1/2 35C 3014 1.33 50 100 0.5

2 35C 3020 1.45 25 50 0.82-1/2 35C 3024 1.70 18 36 1.6

Fig. 35X 3 – Cross

Fig. 35RX3 – Reducing Cross

Fig. 35C 3 – Cap

Sizein Part Number

Ain


3/8 35BC3003 0.75 100 200 0.31/2 35BC3004 0.75 80 160 0.5

Fig. 35BC3 – Beam Clamp

A



Fig. 65LF & 66LFLightweight Flexible Coupling with “C” Gasket• Maximum working pressure 500 psi (34.5 bar) depending on coupling size

and schedule of pipe • All housings, gaskets and bolts identified by SCI logo • 100% magnetic particle inspection of each bolt• Each bolt has a minimum tensile strength of 110,000 psi • Gaskets are pre-lubricated • Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Gasket Grade T - Nitrile (orange stripe) -20˚F (-29˚C) to +180˚F (+82˚C)

• Gasket Grade O - Fluoroelastomer (blue stripe) +20°F (-6°C) to +300°F (+149°C)• Ductile iron housings conform to ASTM A-536 Grade 65-45-12• Groove Dimensions to AWWA C-606• Finishes: Orange enamel paint

Hot dipped galvanized conforming to ASTM A-153 • Smith-Cooper Warranty only applies to assemblies made with housings,

gaskets and bolts carrying the logo

Pipe Size

Part NumberPipe OD Max Pipe

End GapDimensions

Deflection Degrees

Case Qty

WeightPainted Galvanized A B C

in / mm in / mm in / mm in / mm in / mm in / mm lb / kg

1-1/465LF3012 66LF3012

1.660 1/8 2.58 4.09 1.852.1° 36

1.232 42.2 3.2 65.5 103.9 47.0 0.5

1-1/265LF3014 66LF3014

1.900 1/8 2.85 4.37 1.851.9° 36

1.340 48.3 3.2 72.4 111.0 47.0 0.6

265LF3020 66LF3020

2.375 1/8 3.37 4.80 1.852.0° 30

1.750 60.3 3.2 85.6 121.9 47.0 0.8

2-1/265LF3024 66LF3024

2.875 1/8 3.88 5.28 1.852.3° 24

1.965 73.0 3.2 98.6 134.1 47.0 0.9

365LF3030 66LF3030

3.500 1/8 4.40 5.91 1.852.0° 20

2.280 88.9 3.2 111.8 150.1 47.0 1.0

465LF3040 66LF3040

4.500 1/4 5.75 7.44 2.012.2° 18

3.6100 114.3 6.4 146.1 189.0 51.1 1.6

565LF3050 66LF3050

5.563 1/4 6.79 9.13 2.011.8° 12

5.1125 141.3 6.4 172.5 231.9 51.1 2.3

665LF3060 66LF3060

6.625 1/4 7.95 10.31 2.011.6° 10

6.0150 168.3 6.4 201.9 261.9 51.1 2.7

865LF3080 66LF3080

8.625 1/4 10.80 13.07 2.521.4° -

10.7200 219.1 6.4 274.3 332.0 64.0 4.8

A

BC

Lightweight Flexible Couplings

“C” Style Gasket


Fig. 65LR & 66LRLightweight Rigid Coupling with “C” Gasket• Maximum working pressure 500 psi (34.5 bar) depending on coupling

size and schedule of pipe• All housings, gaskets and bolts identified by SCI logo • 100% magnetic particle inspection of each bolt• Each bolt has a minimum tensile strength of 110,000 psi • Gaskets are pre-lubricated • Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Gasket Grade T - Nitrile (orange stripe) -20˚F (-29˚C) to +180˚F (+82˚C)

• Gasket Grade O - Fluoroelastomer (blue stripe) +20°F (-6°C) to +300°F (+149°C)• Ductile iron housings conform to ASTM A-536 Grade 65-45-12• Groove dimensions to AWWA C-606 • Finishes: Orange enamel paint

Hot dipped galvanized conforming to ASTM A-153 • Smith-Cooper Warranty only applies to assemblies made with housings,


Pipe Size

Part NumberPipe OD Max Pipe

End GapDimensions

Case Qty


in / mm in / mm in / mm in / mm in / mm in / mm lb / kg

1-1/465LR3012 66LR3012

1.660 1/16 2.66 4.09 1.8536

1.332 42.2 1.6 67.6 103.9 47.0 0.6

1-1/265LR3014 66LR3014

1.900 1/16 2.93 4.37 1.8536

1.440 48.3 1.6 74.4 111.0 47.0 0.6

265LR3020 66LR3020

2.375 1/16 3.44 4.80 1.8530

1.750 60.3 1.6 87.4 121.9 47.0 0.8

2-1/265LR3024 66LR3024

2.875 1/16 3.96 5.28 1.8524

2.065 73.0 1.6 100.6 134.1 47.0 0.9

365LR3030 66LR3030

3.500 1/16 4.55 5.91 1.8520

2.280 88.9 1.6 115.6 150.1 47.0 1.0

465LR3040 66LR3040

4.500 1/8 5.83 7.28 2.0118

3.4100 114.3 3.2 148.1 184.9 51.1 1.5

565LR3050 66LR3050

5.563 1/8 6.87 8.62 2.0112

4.4125 141.3 3.2 174.5 218.9 51.1 2.0

665LR3060 66LR3060

6.625 1/8 8.03 9.76 2.0110

5.4150 168.3 3.2 204.0 247.9 51.1 2.4

865LR3080 66LR3080

8.625 1/8 10.16 12.52 2.52-

10.5200 219.1 3.2 258.1 318.0 64.0 4.8

B

A

C

Lightweight Rigid Couplings

“C” Style Gasket


Fig. 65RC & 66RCReducing Coupling• Maximum working pressure 300 psi (20.7 bar) depending on coupling

size and schedule of pipe• All housings, gaskets and bolts identified by SCI logo • 100% magnetic particle inspection of each bolt• Each bolt has a minimum tensile strength of 110,000 psi • Gaskets are pre-lubricated • Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Gasket Grade T - Nitrile (orange stripe) -20˚F (-29˚C) to +180˚F (+82˚C)• Other gasket materials available by special order • Ductile iron housings conform to ASTM A-536 Grade 65-45-12• Groove dimensions to AWWA C-606 • Finishes: Orange enamel paint

Hot dipped galvanized conforming to ASTM A-153 • Smith-Cooper Warranty only applies to assemblies made with

housings, gaskets and bolts carrying the logo

Reducing Coupling

Reducing Gasket

Pipe SizePart Number Max Pipe

End GapDimensions

Deflection Degrees

Case Qty


in / mm in / mm in / mm in / mm in / mm lb / kg

2 x 1-1/265RC3020014 66RC3020014

1/8 3.43 4.88 1.852.0° 26

1.950 x 40 3.2 87.1 124.0 47.0 0.9

2-1/2 x 265RC3024020 66RC3024020

1/8 3.98 5.35 1.851.5° 22

2.365 x 50 3.2 101.1 135.9 47.0 1.0

3 x 265RC3030020 66RC3030020

1/8 4.51 6.34 1.851.8° 20

3.180 x 50 3.2 114.5 161.0 47.0 1.4

3 x 2-1/265RC3030024 66RC3030024

1/8 4.51 6.34 1.851.8° 20

3.080 x 65 3.2 114.5 161.0 47.0 1.3

4 x 265RC3040020 66RC3040020

1/4 5.83 7.52 2.011.2° 10

4.8100 x 50 6.4 148.1 191.0 51.1 2.2

4 x 2-1/265RC3040024 66RC3040024

1/4 5.83 7.52 2.011.2° 10

4.8100 x 65 6.4 148.1 191.0 51.1 2.2

4 x 365RC3040030 66RC3040030

1/4 5.83 7.52 2.011.2° 10

4.4100 x 80 6.4 148.1 191.0 51.1 2.0

6 x 465RC3060040 66RC3060040

1/4 7.99 10.35 2.010.9° -

9.0150 x 100 6.4 202.9 262.9 51.1 4.1

8 x 665RC3080060 66RC3080060

1/4 10.12 13.15 2.480.8° -

14.6200 x 150 6.4 257.0 334.0 63.0 6.6

B

A

C


Hinged Flange Adapter

Fig. 65FH & 66FHHinged Flange Adapter• Maximum working pressure 300 psi (20.7 bar) depending on flange

size and schedule of pipe • 3/8" x 2-3/4" latch bolt included • SCI does not provide flange bolts • All bolts and gaskets identified by SCI logo • 100% magnetic particle inspection of each bolt• Each bolt has a minimum tensile strength of 110,000 psi • Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Gasket Grade T - Nitrile (orange stripe) -20˚F (-29˚C) to +180˚F (+82˚C) • Ductile iron housings conform to ASTM A-536 Grade 65-45-12• Groove dimensions to AWWA C-606• Matches Class 125/150 flange dimensions • Finishes: Orange enamel paint

Hot dipped galvanized conforming to ASTM A-153 • Smith-Cooper Warranty only applies to assemblies made with


Pipe Size

Part Number PipeOD

Dimensions Number of Flange

BoltsCase Qty

WeightPart Number

Painted Galvanized A B C Phenolic Flange Ringin / mm in / mm in / mm in / mm in / mm lb / kg

265FH3020 66FH3020

2.375 6.00 4.75 0.754 10

3.665FHR020

50 60.3 152.4 120.7 19.1 1.6

2-1/265FH3024 66FH3024

2.875 7.00 5.50 0.884 10

3.665FHR024

65 73.0 177.8 139.7 22.4 1.6

365FH3030 66FH3030

3.500 7.50 6.00 0.944 10

4.865FHR030

80 88.9 190.5 152.4 23.9 2.2

465FH3040 66FH3040

4.500 9.00 7.50 0.948 10

6.665FHR040

100 114.3 228.6 190.5 23.9 3.0

565FH3050 66FH3050

5.563 10.00 8.50 0.948 -

8.165FHR050

125 141.3 254.0 215.9 23.9 3.7

665FH3060 66FH3060

6.625 11.00 9.50 1.008 -

8.465FHR060

150 168.3 279.4 241.3 25.4 3.8

865FH3080 66FH3080

8.625 13.50 11.75 1.128 -

14.365FHR080

200 219.1 342.9 298.5 28.4 6.5

1065FH3100 66FH3100

10.750 16.00 14.25 1.1912 -

19.465FHR100

250 273.0 406.4 361.9 30.2 8.0

1265FH3120 66FH3120

12.750 19.00 17.00 1.2512 -

28.865FHR120

300 323.9 482.6 431.8 31.7 13.0

A C

B

65FH

4˝

ANSI

150

65FH 4˝

ANSI 150

Phenolic Flange Ring

Fig. 65FHRPhenolic Flange Ring• For use when mating to a rubber flange seal or

wafer-style butterfly valve• 1/8" thick fabric-reinforced, laminated phenolic• Available upon request


Fig. 65E & 66E 90° Elbow, Standard Radius• Ductile Iron - Full Flow• UL/FM – 1-1/4" to 12" only

Fig. 65F & 66F45° Elbow, Standard Radius• Ductile Iron - Full Flow • UL/FM – 1-1/4" to 12" only

Standard Radius Grooved Fittings

A

A

A

18" through 24" sizes available upon request.


Pipe Size Part Number A Case Qty

Weightin / mm Painted Galvanized in / mm lb / kg1-1/4 65E 3012 66E 3012 2.75 50 1.0

32 69.9 0.41-1/2 65E 3014 66E 3014 2.75 36 1.2

40 69.9 0.52 65E 3020 66E 3020 3.25 20 2.150 82.6 0.9

2-1/2 65E 3024 66E 3024 3.75 12 2.765 95.3 1.23 65E 3030 66E 3030 4.25 15 3.880 108.0 1.74 65E 3040 66E 3040 5.00 8 7.6

100 127.0 3.45 65E 3050 66E 3050 5.50 - 10.6

125 139.7 4.86 65E 3060 66E 3060 6.50 - 15.7

150 165.1 7.18 65E 3080 66E 3080 7.75 - 28.7

200 196.9 13.010 65E 3100 66E 3100 9.00 - 50.7250 229.0 23.012 65E 3120 66E 3120 10.00 - 70.1300 254.0 31.814 65E 3140 66E 3140 14.00 - 106.9350 356.0 48.516 65E 3160 66E 3160 16.00 - 158.7400 406.0 72.0


Weightin / mm Painted Galvanized in / mm lb / kg1-1/4 65F 3012 66F 3012 1.75 65 0.7

32 44.5 0.31-1/2 65F 3014 66F 3014 1.75 55 0.8

40 44.5 0.42 65F 3020 66F 3020 2.00 30 1.550 50.8 0.7

2-1/2 65F 3024 66F 3024 2.25 20 2.065 57.2 0.93 65F 3030 66F 3030 2.50 10 2.880 63.5 1.34 65F 3040 66F 3040 3.00 12 4.7

100 76.2 2.25 65F 3050 66F 3050 3.25 - 7.5

125 82.6 3.46 65F 3060 66F 3060 3.50 - 9.8

150 88.9 4.58 65F 3080 66F 3080 4.25 - 19.5

200 108.0 8.810 65F 3100 66F 3100 4.75 - 30.3250 121.0 13.712 65F 3120 66F 3120 5.25 - 42.7300 133.0 19.414 65F 3140 66F 3140 5.79 - 51.8350 147.0 23.516 65F 3160 66F 3160 6.61 - 72.7400 168.0 33.0

NOTE: COOPLOK™ Grooved fittings assume the pressure rating of the grooved coupling being used.


Fig. 65TT & 66TT22-1/2° Elbow, Standard Radius• Ductile Iron - Full Flow• (F) Fabricated Steel - Sch40, Cut Groove

Fig. 65EL & 66EL11-1/4° Elbow, Standard Radius• Ductile Iron - Full Flow• (F) Fabricated Steel - Sch40, Cut Groove


A

A



Weightin / mm Painted Galvanized in / mm lb / kg1-1/4 65TT3012 66TT3012 1.75 85 0.7

32 44.5 0.31-1/2 65TT3014 66TT3014 1.75 75 0.8

40 44.5 0.42 65TT3020 66TT3020 1.88 30 1.250 47.8 0.5

2-1/2 65TT3024 66TT3024 2.00 24 1.565 50.8 0.73 65TT3030 66TT3030 2.25 14 2.380 57.2 1.04 65TT3040 66TT3040 2.62 16 3.8

100 66.5 1.75 65TT3050 66TT3050 2.88 - 5.9

125 73.2 2.76 65TT3060 66TT3060 3.12 - 8.2

150 79.2 3.78 65TT3080 66TT3080 3.88 - 16.2

200 98.6 7.310 65TT3100F 66TT3100F 4.38 - 30.0250 111.2 13.612 65TT3120F 66TT3120F 4.88 - 40.0300 123.9 18.1


Weightin / mm Painted Galvanized in / mm lb / kg1-1/4 65EL3012 66EL3012 1.37 115 0.6

32 34.8 0.31-1/2 65EL3014 66EL3014 1.37 90 0.7

40 34.8 0.32 65EL3020 66EL3020 1.37 60 0.850 34.8 0.4

2-1/2 65EL3024 66EL3024 1.50 36 1.265 38.1 0.53 65EL3030 66EL3030 1.50 18 1.680 38.1 0.74 65EL3040 66EL3040 1.75 24 2.8

100 44.5 1.35 65EL3050 66EL3050 2.00 - 4.3

125 50.8 2.06 65EL3060 66EL3060 2.00 - 5.5

150 50.8 2.58 65EL3080 66EL3080 2.00 - 8.3

200 50.8 3.810 65EL3100F 66EL3100F 2.13 - 20.0250 54.1 9.112 65EL3120F 66EL3120F 2.25 - 30.0300 57.1 13.6



Please see complete installation instructions at www.smithcooper.com for important guidelines and limitations on the use and applications of SCI COOPLOK™, Grooved Couplings and Fittings.


Fig. 65T & 66TTee, Standard Radius• Ductile Iron - Full Flow• UL/FM – 1-1/4" to 12" only

Fig. 65X & 66XCross, Standard Radius• Ductile Iron - Full Flow• UL/FM – 1-1/4" to 8" only

Fig. 65FA & 66FAGrooved x Flange Adapter• Ductile Iron• UL/FM – 2" to 8" only• Matches Class 125/150 flange dimensions


A

A

A

A

A



5" & 14" through 24" sizes available upon request.


Weightin / mm Painted Galvanized in / mm lb / kg1-1/4 65T 3012 66T 3012 2.75 35 1.4

32 69.9 0.71-1/2 65T 3014 66T 3014 2.75 24 1.7

40 69.9 0.82 65T 3020 66T 3020 3.25 15 3.150 82.6 1.4

2-1/2 65T 3024 66T 3024 3.75 7 4.165 95.3 1.93 65T 3030 66T 3030 4.25 10 5.880 108.0 2.64 65T 3040 66T 3040 5.00 5 10.0

100 127.0 4.55 65T 3050 66T 3050 5.50 - 15.0

125 139.7 6.86 65T 3060 66T 3060 6.50 - 22.3

150 165.1 10.18 65T 3080 66T 3080 7.75 - 41.1

200 196.9 18.610 65T 3100 66T 3100 9.00 - 64.8250 229.0 29.412 65T 3120 66T 3120 10.00 - 90.9300 254.0 41.214 65T 3140 66T 3140 11.00 - 116.8350 279.0 53.016 65T 3160 66T 3160 12.00 - 145.0400 305.0 65.9


Weightin / mm Painted Galvanized in / mm lb / kg1-1/4 65X 3012 66X 3012 2.75 20 1.8

32 69.9 0.81-1/2 65X 3014 66X 3014 2.75 16 2.0

40 69.9 0.92 65X 3020 66X 3020 3.25 20 3.350 82.6 1.5

2-1/2 65X 3024 66X 3024 3.75 10 4.965 95.3 2.23 65X 3030 66X 3030 4.25 7 7.380 108.0 3.34 65X 3040 66X 3040 5.00 4 10.0

100 127.0 4.55 65X 3050 66X 3050 5.50 - 15.3

125 139.7 6.96 65X 3060 66X 3060 6.50 - 24.6

150 165.1 11.18 65X 3080 66X 3080 7.75 - 41.6

200 196.9 18.9


Weightin / mm Painted Galvanized in / mm lb / kg

2 65FA3020 66FA3020 4.00 8 4.050 101.6 1.8

2-1/2 65FA3024 66FA3024 4.00 5 5.465 101.6 2.53 65FA3030 66FA3030 4.00 4 6.480 101.6 2.94 65FA3040 66FA3040 6.00 - 12.7

100 152.4 5.86 65FA3060 66FA3060 6.00 - 19.0

150 152.4 8.68 65FA3080 66FA3080 6.00 - 28.8

200 152.4 13.110 65FA3100F 66FA3100F 8.00 - 66.0250 203.2 30.012 65FA3120F 66FA3120F 10.00 - 97.0300 254.0 44.1



Fig. 65AE & 66AE Adapter Elbow, Grooved x Threaded• Ductile Iron - Full Flow• Threads meet ASME B1.20.1

Fig. 65C & 66CCap• Ductile Iron

Grooved Fittings


Weightin / mm Painted Galvanized in / mm lb / kg1-1/4 65C 3012 66C 3012 0.88 200 0.3

32 22.4 0.11-1/2 65C 3014 66C 3014 0.88 140 0.4

40 22.4 0.22 65C 3020 66C 3020 0.88 80 0.650 22.4 0.3

2-1/2 65C 3024 66C 3024 0.88 60 1.065 22.4 0.53 65C 3030 66C 3030 0.88 40 1.580 22.4 0.74 65C 3040 66C 3040 1.00 24 2.6

100 25.4 1.25 65C 3050 66C 3050 1.00 12 4.0

125 25.4 1.86 65C 3060 66C 3060 1.00 10 5.4

150 25.4 2.58 65C 3080 66C 3080 1.19 5 11.5

200 30.2 5.210 65C 3100 66C 3100 1.26 - 17.7250 32.0 8.012 65C 3120 66C 3120 1.26 - 23.6300 32.0 10.7

A

A

B


Pipe Size Part Number A B Case Qty

Weightin / mm Painted Galvanized in / mm in / mm lb / kg

1-1/4 x 1/2 65AE3012004 66AE3012004 1.88 1.75 90 0.632 x 15 48.0 44.4 0.3

1-1/4 x 3/4 65AE3012006 66AE3012006 1.88 1.75 90 0.632 x 20 48.0 44.5 0.3

1-1/4 x 1 65AE3012010 66AE3012010 2.02 2.00 75 0.832 x 25 51.3 50.8 0.3

1-1/2 x 1/2 65AE3014004 66AE3014004 1.88 1.75 69 0.640 x 15 48.0 44.4 0.3

1-1/2 x 3/4 65AE3014006 66AE3014006 1.88 1.75 69 0.740 x 20 48.0 44.4 0.3

1-1/2 x 1 65AE3014010 66AE3014010 2.02 2.00 60 0.840 x 25 51.3 50.8 0.42 x 1/2 65AE3020004 66AE3020004 1.88 1.75 45 0.850 x 15 48.0 44.4 0.42 x 3/4 65AE3020006 66AE3020006 1.88 1.75 45 0.950 x 20 48.0 44.4 0.42 x 1 65AE3020010 66AE3020010 2.02 2.00 45 1.0

50 x 25 51.3 50.8 0.52-1/2 x 1/2 65AE3024004 66AE3024004 1.88 1.97 36 1.0

65 x 15 48.0 50.0 0.52-1/2 x 3/4 65AE3024006 66AE3024006 1.88 1.97 36 1.1

65 x 20 48.0 50.0 0.52-1/2 x 1 65AE3024010 66AE3024010 2.02 2.00 36 1.2

65 x 25 51.3 50.8 0.5




Fig. 65RT & 66RT Reducing Tee• Ductile Iron sizes – Full Flow• UL/FM – 1-1/2" to 8"• (F) Fabricated steel fittings –

Schedule 40, cut grooved

Grooved Fittings

A

A

SCI

*Other sizes and configurations available by special order.

Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg

1-1/2 x 1-1/4 65RT3014012F 66RT3014012F 2.75 1.740 x 32 70.0 0.8

2 x 1-1/4 65RT3020012F 66RT3020012F 3.25 2.550 x 32 82.6 1.2

2 x 1-1/2 65RT3020014 66RT3020014 3.25 2.650 x 40 82.6 1.2

2-1/2 x 1-1/4 65RT3024012F 66RT3024012F 3.75 4.165 x 32 95.3 1.9

2-1/2 x 1-1/2 65RT3024014F 66RT3024014F 3.75 4.565 x 40 95.3 2.0

2-1/2 x 2 65RT3024020 66RT3024020 3.75 3.565 x 50 95.3 1.8

3 x 1-1/4 65RT3030012F 66RT3030012F 4.25 6.280 x 32 108.0 2.8

3 x 1-1/2 65RT3030014 66RT3030014 4.25 6.180 x 40 108.0 2.83 x 2 65RT3030020 66RT3030020 4.25 6.4

80 x 50 108.0 2.93 x 2-1/2 65RT3030024 66RT3030024 4.25 5.2

80 x 65 108.0 2.34 x 1-1/4 65RT3040012F 66RT3040012F 5.00 9.7100 x 32 127.0 4.44 x 1-1/2 65RT3040014F 66RT3040014F 5.00 10.4100 x 40 127.0 4.7

4 x 2 65RT3040020 66RT3040020 5.00 8.3100 x 50 127.0 3.84 x 2-1/2 65RT3040024 66RT3040024 5.00 7.9100 x 65 127.0 3.6

4 x 3 65RT3040030 66RT3040030 5.00 8.1100 x 80 127.0 3.75 x 1-1/4 65RT3050012F 66RT3050012F 5.50 14.5125 x 32 139.7 6.65 x 1-1/2 65RT3050014F 66RT3050014F 5.50 14.7125 x 40 139.7 6.7

5 x 2 65RT3050020F 66RT3050020F 5.50 14.6125 x 50 139.7 6.65 x 2-1/2 65RT3050024F 66RT3050024F 5.50 14.1125 x 65 139.7 5.9

5 x 3 65RT3050030F 66RT3050030F 5.50 14.7125 x 80 139.7 6.2

5 x 4 65RT3050040F 66RT3050040F 5.50 14.7125 x 100 139.7 6.76 x 1-1/4 65RT3060012F 66RT3060012F 6.50 21.1150 x 32 165.1 9.66 x 1-1/2 65RT3060014F 66RT3060014F 6.50 21.2150 x 40 165.1 9.6

6 x 2 65RT3060020 66RT3060020 6.50 21.5150 x 50 165.1 9.86 x 2-1/2 65RT3060024 66RT3060024 6.50 19.0150 x 65 165.1 8.6

6 x 3 65RT3060030 66RT3060030 6.50 18.5150 x 80 165.1 8.4

6 x 4 65RT3060040 66RT3060040 6.50 18.7150 x 100 165.1 8.5

Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg6 x 5 65RT3060050F 66RT3060050F 6.50 26.4

150 x 125 165.1 12.08 x 2 65RT3080020F 66RT3080020F 7.75 38.1

200 x 50 196.9 17.38 x 2-1/2 65RT3080024F 66RT3080024F 7.75 38.8200 x 65 196.9 17.6

8 x 3 65RT3080030 66RT3080030 7.75 34.7200 x 80 196.9 17.9

8 x 4 65RT3080040 66RT3080040 7.75 34.5200 x 100 196.9 15.7

8 x 5 65RT3080050 66RT3080050 7.75 40.5200 x 125 196.9 18.3

8 x 6 65RT3080060 66RT3080060 7.75 36.4200 x 150 196.9 16.5

10 x 2 65RT3100020F 66RT3100020F 9.00 63.5250 x 50 228.6 28.8

10 x 2-1/2 65RT3100024F 66RT3100024F 9.00 65.1250 x 65 228.6 29.510 x 3 65RT3100030F 66RT3100030F 9.00 66.4

250 x 80 228.6 30.110 x 4 65RT3100040F 66RT3100040F 9.00 68.8

250 x 100 228.6 24.310 x 5 65RT3100050F 66RT3100050F 9.00 71.7

250 x 150 228.6 32.510 x 6 65RT3100060 66RT3100060 9.00 69.5

250 x 150 228.6 31.510 x 8 65RT3100080 66RT3100080 9.00 78.2

250 x 200 228.6 35.412 x 2 65RT3120020F 66RT3120020F 10.00 84.2

300 x 50 254.0 38.212 x 2-1/2 65RT3120024F 66RT3120024F 10.00 85.2

300 x 65 254.0 38.712 x 3 65RT3120030F 66RT3120030F 10.00 86.1

300 x 80 254.0 39.112 x 4 65RT3120040F 66RT3120040F 10.00 87.7

300 x 100 254.0 39.812 x 5 65RT3120050F 66RT3120050F 10.00 89.6

300 x 125 254.0 40.712 x 6 65RT3120060F 66RT3120060F 10.00 98.1

300 x 150 254.0 44.512 x 8 65RT3120080F 66RT3120080F 10.00 106.1

300 x 200 254.0 48.112 x 10 65RT3120100F 66RT3120100F 10.00 116.0

300 x 250 254.0 52.614 x 4 65RT3140040F 66RT3140040F 11.00 109.8

350 x 100 279.4 49.814 x 6 65RT3140060F 66RT3140060F 11.00 117.4

350 x 150 279.4 53.214 x 8 65RT3140080F 66RT3140080F 11.00 126.2

350 x 200 279.4 57.314 x 10 65RT3140100F 66RT3140100F 11.00 137.2

350 x 250 279.4 62.214 x 12 65RT3140120F 66RT3140120F 11.00 145.6

350 x 300 279.4 66.0



Fig. 65RTT & 66RTTReducing Tee - Grooved x Male NPT • (F) Fabricated steel fittings – all sizes

Schedule 40, cut grooved• UL/FM – 2" to 8"• Male NPT threads conform to ASME B1.20.1 A

A

Grooved Fittings

*Other sizes and configurations available by special order.

Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg2 x 1 65RTT3020010F 66RTT3020010F 3.25 2.3

50 x 25 82.6 1.02 x 1-1/4 65RTT3020012F 66RTT3020012F 3.25 2.5

50 x 32 82.6 1.12 x 1-1/2 65RTT3020014F 66RTT3020014F 3.25 2.5

50 x 40 82.6 1.12-1/2 x 1 65RTT3024010F 66RTT3024010F 3.75 4.0

65 x 25 95.3 1.82-1/2 x 1-1/4 65RTT3024012F 66RTT3024012F 3.75 4.4

65 x 32 95.3 1.92-1/2 x 1-1/2 65RTT3024014F 66RTT3024014F 3.75 4.5

65 x 40 95.3 2.02-1/2 x 2 65RTT3024020F 66RTT3024020F 3.75 4.5

65 x 50 95.3 2.03 x 1 65RTT3030010F 66RTT3030010F 4.25 6.0

80 x 25 108.0 2.73 x 1-1/4 65RTT3030012F 66RTT3030012F 4.25 6.2

80 x 32 108.0 2.83 x 1-1/2 65RTT3030014F 66RTT3030014F 4.25 6.3

80 x 40 108.0 2.83 x 2 65RTT3030020F 66RTT3030020F 4.25 6.8

80 x 50 108.0 3.13 x 2-1/2 65RTT3030024F 66RTT3030024F 4.25 7.1

80 x 65 108.0 3.24 x 1 65RTT3040010F 66RTT3040010F 5.00 9.7

100 x 25 127.0 4.34 x 1-1/4 65RTT3040012F 66RTT3040012F 5.00 9.7100 x 32 127.0 4.44 x 1-1/2 65RTT3040014F 66RTT3040014F 5.00 10.1100 x 40 127.0 4.5

4 x 2 65RTT3040020F 66RTT3040020F 5.00 10.8100 x 50 127.0 4.94 x 2-1/2 65RTT3040024F 66RTT3040024F 5.00 10.9100 x 65 127.0 4.9

4 x 3 65RTT3040030F 66RTT3040030F 5.00 11.5100 x 80 127.0 5.2


5 x 3 65RTT3050030F 66RTT3050030F 5.50 16.9125 x 80 139.7 7.7

5 x 4 65RTT3050040F 66RTT3050040F 5.50 17.9125 x 100 139.7 8.1


Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg6 x 3 65RTT3060030F 66RTT3060030F 6.50 22.0

150 x 80 165.1 10.06 x 4 65RTT3060040F 66RTT3060040F 6.50 24.7

150 x 100 165.1 11.26 x 5 65RTT3060050F 66RTT3060050F 6.50 27.8

150 x 125 165.1 12.68 x 2 65RTT3080020F 66RTT3080020F 7.75 37.4

200 x 50 196.9 17.08 x 2-1/2 65RTT3080024F 66RTT3080024F 7.75 38.0200 x 65 196.9 17.2

8 x 3 65RTT3080030F 66RTT3080030F 7.75 38.6200 x 80 196.9 17.5

8 x 4 65RTT3080040F 66RTT3080040F 7.75 40.5200 x 100 196.9 18.3

8 x 5 65RTT3080050F 66RTT3080050F 7.75 42.0200 x 125 196.9 19.0

8 x 6 65RTT3080060F 66RTT3080060F 7.75 51.0200 x 150 196.9 23.1

10 x 2 65RTT3100020F 66RTT3100020F 9.00 61.8250 x 50 228.6 28.010 x 3 65RTT3100030F 66RTT3100030F 9.00 63.3

250 x 80 228.6 28.710 x 4 65RTT3100040F 66RTT3100040F 9.00 64.0

250 x 100 228.6 29.010 x 5 65RTT3100050F 66RTT3100050F 9.00 65.1

250 x 125 228.6 29.510 x 6 65RTT3100060F 66RTT3100060F 9.00 64.8

250 x 150 228.6 24.910 x 8 65RTT3100080F 66RTT3100080F 9.00 64.5

250 x 200 228.6 29.312 x 3 65RTT3120030F 66RTT3120030F 10.00 84.5

300 x 80 254.0 38.412 x 4 65RTT3120040F 66RTT3120040F 10.00 85.7

300 x 100 254.0 38.912 x 5 65RTT3120050F 66RTT3120050F 10.00 87.0

300 x 125 254.0 39.512 x 6 65RTT3120060F 66RTT3120060F 10.00 88.2

300 x 150 254.0 40.012 x 8 65RTT3120080F 66RTT3120080F 10.00 91.0

300 x 200 254.0 41.312 x 10 65RTT3120100F 66RTT3120100F 10.00 94.7

300 x 250 254.0 43.014 x 8 65RTT3140080F 66RTT3140080F 11.00 110.0

350 x 200 279.4 50.014 x 10 65RTT3140100F 66RTT3140100F 11.00 114.0

350 x 250 279.4 51.814 x 12 65RTT3140120F 66RTT3140120F 11.00 117.0

350 x 300 279.4 53.1




Fig. 65CR & 66CR Concentric Reducer• Ductile Iron sizes – Full Flow• UL/FM – 2" to 8"• (F) Fabricated steel fittings –


Grooved Fittings

A

(F) Fabricated fitting "A" dimension may differ from other manufacturers' products.Other sizes and configurations available by special order.

Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg2 x 1 65CR3020010F 66CR3020010F 2.50 0.8

50 x 25 64.0 0.42 x 1-1/4 65CR3020012 66CR3020012 2.50 0.7

50 x 32 64.0 0.32 x 1-1/2 65CR3020014 66CR3020014 2.50 0.8

50 x 40 64.0 0.42-1/2 x 1 65CR3024010F 66CR3024010F 2.50 1.0

65 x 25 64.0 0.52-1/2 x 1-1/4 65CR3024012 66CR3024012 2.50 1.1

65 x 32 64.0 0.502-1/2 x 1-1/2 65CR3024014 66CR3024014 2.50 1.0

65 x 40 64.0 0.52-1/2 x 2 65CR3024020 66CR3024020 2.50 1.1

65 x 50 64.0 0.53 x 1 65CR3030010F 66CR3030010F 2.50 1.3

80 x 25 64.0 0.63 x 1-1/4 65CR3030012 66CR3030012 2.50 1.4

80 x 32 64.0 0.63 x 1-1/2 65CR3030014 66CR3030014 2.50 1.3

80 x 40 64.0 0.63 x 2 65CR3030020 66CR3030020 2.50 1.3

80 x 50 64.0 0.63 x 2-1/2 65CR3030024 66CR3030024 2.50 1.4

80 x 65 64.0 0.63-1/2 x 3 65CR3034030F 66CR3034030F 2.50 2.8

90 x 80 64.0 1.34 x 1 65CR3040010F 66CR3040010F 3.00 2.1

100 x 25 76.2 1.04 x 1-1/4 65CR3040012F 66CR3040012F 3.00 1.7100 x 32 76.2 0.84 x 1-1/2 65CR3040014 66CR3040014 3.00 2.3100 x40 76.2 1.04 x 2 65CR3040020 66CR3040020 3.00 2.3

100 x 50 76.2 1.04 x 2-1/2 65CR3040024 66CR3040024 3.00 2.5100 x 65 76.2 1.0

4 x 3 65CR3040030 66CR3040030 3.00 2.4100 x 80 76.2 1.04 x 3-1/2 65CR3040034F 66CR3040034F 3.00 2.8100 x 90 76.2 1.3

5 x 2 65CR3050020F 66CR3050020F 4.00 2.7125 x 50 102.1 1.25 x 2-1/2 65CR3050024F 66CR3050024F 4.00 3.1125 x 65 102.1 1.4

5 x 3 65CR3050030 66CR3050030 3.50 3.3125 x 80 89.0 1.5

Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg5 x 4 65CR3050040 66CR3050040 3.50 3.7

125 x 100 89.0 1.76 x 1 65CR3060010F 66CR3060010F 4.00 4.1

150 x 25 102.1 1.96 x 1-1/2 65CR3060014F 66CR3060014F 4.00 4.3150 x 40 102.1 2.0

6 x 2 65CR3060020 66CR3060020 4.00 5.5150 x 50 102.1 2.56 x 2-1/2 65CR3060024 66CR3060024 4.00 5.7150 x 65 102.1 2.6

6 x 3 65CR3060030 66CR3060030 4.00 5.3150 x 80 102.1 2.4

6 x 4 65CR3060040 66CR3060040 4.00 5.4150 x 100 102.1 2.5

6 x 5 65CR3060050 66CR3060050 4.00 5.7150 x 125 102.1 2.6

8 x 3 65CR3080030 66CR3080030 5.00 10.5200 x 80 127.0 4.8

8 x 4 65CR3080040 66CR3080040 5.0 10.2200 x 100 127.0 4.6

8 x 5 65CR3080050 66CR3080050 5.00 10.9200 x 125 127.0 5.0

8 x 6 65CR3080060 66CR3080060 5.00 10.6200 x 150 127.0 4.8

10 x 4 65CR3100040 66CR3100040 6.00 22.0250 x 100 152.0 10.0

10 x 5 65CR3100050F 66CR3100050F 6.00 21.7250 x 125 152.0 9.9

10 x 6 65CR3100060 66CR3100060 6.00 21.3250 x 100 152.0 9.7

10 x 8 65CR3100080 66CR3100080 6.00 20.7250 x 200 152.0 9.4

12 x 6 65CR3120060F 66CR3120060F 7.00 26.5300 x 150 178.0 12.0

12 x 8 65CR3120080F 66CR3120080F 7.00 30.7300 x 200 178.0 14.012 x 10 65CR3120100F 66CR3120100F 7.00 32.2

300 x 250 178.0 14.614 x 6 65CR3140060F 66CR3140060F 13.00 94.5

350 x 150 330.2 43.014 x 8 65CR3140080F 66CR3140080F 13.00 100.0

350 x 200 330.2 45.5 14 x 10 65CR3140100F 66CR3140100F 13.00 107.0350 x 250 330.2 48.614 x 12 65CR3140120F 66CR3140120F 13.00 113.0

350 x 300 330.2 51.7



Fig. 65CRT & 66CRTConcentric Reducer Male NPT• (F) Fabricated steel fittings –

Schedule 40, cut grooved• UL/FM – 1-1/2" to 8"• Male NPT threads conform to ASME B1.20.1

Grooved Fittings

A



1-1/2 x 1 65CRT3024010F 66CRT3024010F 3.75 0.665 x 25 95.3 0.32 x 1 65CRT3020010F 66CRT3020010F 3.75 1.5

50 x 25 95.3 0.72 x 1-1/4 65CRT3020012F 66CRT3020012F 3.75 1.5

50 x 32 95.3 0.72 x 1-1/2 65CRT3020014F 66CRT3020014F 3.75 1.5

50 x 40 95.3 0.72-1/2 x 1 65CRT3024010F 66CRT3024010F 3.75 1.6

65 x 25 95.3 0.72-1/2 x 1-1/4 65CRT3024012F 66CRT3024012F 3.75 1.6

65 x 32 95.3 0.72-1/2 x 1-1/2 65CRT3024014F 66CRT3024014F 3.75 1.5

65 x 40 95.3 0.72-1/2 x 2 65CRT3024020F 66CRT3024020F 3.75 1.7

65 x 50 95.3 0.83 x 1 65CRT3030010F 66CRT3030010F 3.75 2.6

80 x 25 95.3 1.13 x 1-1/4 65CRT3030012F 66CRT3030012F 3.75 2.7

80 x 32 95.3 1.23 x 1-1/2 65CRT3030014F 66CRT3030014F 3.75 2.8

80 x 40 95.3 1.23 x 2 65CRT3030020F 66CRT3030020F 3.75 2.7

80 x 50 95.3 1.23 x 2-1/2 65CRT3030024F 66CRT3030024F 3.75 2.5

80 x 65 95.3 1.14 x 1 65CRT3040010F 66CRT3040010F 4.00 3.6

100 x 25 102.1 1.64 x 1-1/4 65CRT3040012F 66CRT3040012F 4.00 3.7100 x 32 102.1 1.74 x 1-1/2 65CRT3040014F 66CRT3040014F 4.00 3.8100 x40 102.1 1.74 x 2 65CRT3040020F 66CRT3040020F 4.00 3.5

100 x 50 102.1 1.64 x 2-1/2 65CRT3040024F 66CRT3040024F 4.00 3.8100 x 65 102.1 1.7

4 x 3 65CRT3040030F 66CRT3040030F 4.00 4.2100 x 80 102.1 1.9

Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg5 x 4 65CRT3050040F 66CRT3050040F 4.25 6.4

125 x 100 108.0 2.96 x 1 65CRT3060010F 66CRT3060010F 4.25 7.9

150 x 25 108.0 3.66 x 1-1/4 65CRT3060012F 66CRT3060012F 4.25 7.9150 x 32 108.0 3.66 x 1-1/2 65CRT3060014F 66CRT3060014F 4.50 8.1150 x 40 112.0 3.7

6 x 2 65CRT3060020F 66CRT3060020F 4.50 8.7150 x 50 112.0 4.0

6 x 3 65CRT3060030F 66CRT3060030F 4.50 9.9150 x 80 112.0 4.5

6 x 4 65CRT3060040F 66CRT3060040F 4.50 9.9150 x 100 112.0 4.5

6 x 5 65CRT3060050F 66CRT3060050F 4.50 9.9150 x 125 112.0 4.5

8 x 3 65CRT3080030F 66CRT3080030F 5.00 14.9200 x 80 127.0 6.7

8 x 4 65CRT3080040F 66CRT3080040F 5.00 14.8200 x 100 127.0 6.7

8 x 5 65CRT3080050F 66CRT3080050F 5.00 15.6200 x 125 127.0 7.0

8 x 6 65CRT3080060F 66CRT3080060F 5.00 18.9200 x 150 127.0 8.5

10 x 4 65CRT3100040F 66CRT3100040F 6.00 31.9250 x 100 152.0 14.4

10 x 5 65CRT3100050F 66CRT3100050F 6.00 31.0250 x 125 152.0 12.74

10 x 6 65CRT3100060F 66CRT3100060F 6.00 31.9250 x 150 152.0 14.4

10 x 8 65CRT3100080F 66CRT3100080F 6.00 34.3250 x 200 152.0 15.6

12 x 4 65CRT3120040F 66CRT3120040F 7.00 33.8300 x 100 178.0 15.4

12 x 6 65CRT3120060F 66CRT3120060F 7.00 38.3300 x 150 178.0 17.4

12 x 8 65CRT3120080F 66CRT3120080F 7.00 41.3300 x 200 178.0 18.7




Fig. 65ER & 66ER Eccentric Reducer• (F) Fabricated steel fittings – Full Flow

Schedule 40, cut grooved• UL/FM – 2" to 8"

Grooved Fittings

A


Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg2 x 1 65ER3020010F 66ER3020010F 9.00 0.8

50 x 25 228.6 0.42 x 1-1/4 65ER3020012F 66ER3020012F 9.00 0.9

50 x 32 228.6 0.42 x 1-1/2 65ER3020014F 66ER3020014F 9.00 1.0

50 x 40 228.6 0.52-1/2 x 1 65ER3024010F 66ER3024010F 9.50 1.0

65 x 25 241.3 0.52-1/2 x 1-1/4 65ER3024012F 66ER3024012F 9.50 1.3

65 x 32 241.3 0.62-1/2 x 1-1/2 65ER3024014F 66ER3024014F 9.50 0.9

65 x 40 241.3 0.42-1/2 x 2 65ER3024020F 66ER3024020F 9.50 1.1

65 x 50 241.3 0.53 x 1 65ER3030010F 66ER3030010F 9.50 1.6

80 x 25 241.3 0.73 x 1-1/4 65ER3030012F 66ER3030012F 9.50 1.7

80 x 32 241.3 0.83 x 1-1/2 65ER3030014F 66ER3030014F 9.50 1.2

80 x 40 241.3 0.53 x 2 65ER3030020F 66ER3030020F 9.50 1.5

80 x 50 241.3 0.73 x 2-1/2 65ER3030024F 66ER3030024F 9.50 1.5

80 x 65 241.3 0.73-1/2 x 3 65ER3034030F 66ER3034030F 9.50 2.8

90 x 80 241.3 1.34 x 1 65ER3040010F 66ER3040010F 10.00 2.1

100 x 25 254.0 1.04 x 1-1/4 65ER3040012F 66ER3040012F 10.00 1.7100 x 32 254.0 0.84 x 1-1/2 65ER3040014F 66ER3040014F 10.00 1.8100 x40 254.0 0.84 x 2 65ER3040020F 66ER3040020F 10.00 2.0

100 x 50 254.0 0.94 x 2-1/2 65ER3040024F 66ER3040024F 10.00 2.3100 x 65 254.0 1.0

4 x 3 65ER3040030F 66ER3040030F 10.00 2.5100 x 80 254.0 1.14 x 3-1/2 65ER3040034F 66ER3040034F 10.00 2.8100 x 90 254.0 1.3


5 x 3 65ER3050030F 66ER3050030F 11.00 3.3125 x 80 279.4 1.5

Pipe Size Part Number A Weightin / mm Painted Galvanized in / mm lb / kg5 x 4 65ER3050040F 66ER3050040F 11.00 3.8

125 x 100 279.4 1.76 x 1 65ER3060010F 66ER3060010F 11.50 4.1

150 x 25 292.1 1.96 x 1-1/2 65ER3060014F 66ER3060014F 11.50 4.3150 x 40 292.1 2.0


6 x 3 65ER3060030F 66ER3060030F 11.50 4.0150 x 80 292.1 1.8

6 x 4 65ER3060040F 66ER3060040F 11.50 7.1150 x 100 292.1 3.2

6 x 5 65ER3060050F 66ER3060050F 11.50 8.2150 x 125 292.1 3.7

8 x 3 65ER3080030F 66ER3080030F 12.00 8.4200 x 80 304.8 3.8

8 x 4 65ER3080040F 66ER3080040F 12.00 8.3200 x 100 304.8 3.8

8 x 5 65ER3080050F 66ER3080050F 12.00 9.1200 x 125 304.8 4.1

8 x 6 65ER3080060F 66ER3080060F 12.00 10.0200 x 150 304.8 4.5

10 x 4 65ER3100040F 66ER3100040F 13.00 14.9250 x 100 330.2 6.8

10 x 5 65ER3100050F 66ER3100050F 13.00 11.0250 x 125 330.2 5.0

10 x 6 65ER3100060F 66ER3100060F 13.00 14.9250 x 150 330.2 6.8

10 x 8 65ER3100080F 66ER3100080F 13.00 17.3250 x 200 330.2 7.8

12 x 6 65ER3120060F 66ER3120060F 14.00 16.3300 x 150 355.6 7.4

12 x 8 65ER3120080F 66ER3120080F 14.00 19.3300 x 200 355.6 8.812 x 10 65ER3120100F 66ER3120100F 14.00 23.0

300 x 250 355.6 10.414 x 6 65ER3140060F 66ER3140060F 13.00 96.0

350 x 150 330.2 43.514 x 8 65ER3140080F 66ER3140080F 13.00 76.6

350 x 200 330.2 34.7 14 x 10 65ER3140100F 66ER3140100F 13.00 77.6350 x 250 330.2 35.214 x 12 65ER3140120F 66ER3140120F 13.00 89.2

350 x 300 330.2 40.5



Fig. 65ELR & 66ELR90° Long Radius Elbow – 1-1/2 D• (F) Fabricated steel fittings – Full Flow (all sizes)


Fig. 65FLR & 66FLR45° Long Radius Elbow – 1-1/2 D• (F) Fabricated steel fittings – Full Flow (all sizes)


Long Radius Fittings (1-1/2 D)

A

SCI

A

SCI

3D, 5D & 6D Long Radius Fittings available on request.


1 65ELR3010F 66ELR3010F 3.00 1.225 76.0 0.5

1-1/4 65ELR3012F 66ELR3012F 3.88 1.432 99.0 0.6

1-1/2 65ELR3014F 66ELR3014F 4.25 1.840 108.0 0.82 65ELR3020F 66ELR3020F 4.38 2.650 111.0 1.2

2-1/2 65ELR3024F 66ELR3024F 5.75 5.165 146.0 2.33 65ELR3030F 66ELR3030F 5.88 6.680 149.0 3.04 65ELR3040F 66ELR3040F 7.50 11.6

100 191.0 5.35 65ELR3050F 66ELR3050F 9.50 20.0

125 241.0 9.16 65ELR3060F 66ELR3060F 10.75 29.5

150 273.0 13.48 65ELR3080F 66ELR3080F 15.00 62.1

200 381.0 28.210 65ELR3100F 66ELR3100F 18.00 103.7250 457.0 47.112 65ELR3120F 66ELR3120F 21.00 147.8300 533.0 67.214 65ELR3140F 66ELR3140F 21.00 159.0350 533.0 72.316 65ELR3160F 66ELR3160F 24.00 211.0400 610.0 95.918 65ELR3180F 66ELR3180F 27.00 269.0450 686.0 122.320 65ELR3200F 66ELR3200F 32.00 332.0500 813.0 150.924 65ELR3240F 66ELR3240F 36.00 470.0600 914.0 213.6


1 65FLR3010F 66FLR3010F 2.50 0.925 64.0 0.4

1-1/4 65FLR3012F 66FLR3012F 2.50 1.132 64.0 0.5

1-1/2 65FLR3014F 66FLR3014F 2.50 1.340 64.0 0.62 65FLR3020F 66FLR3020F 2.75 2.250 70.0 1.0

2-1/2 65FLR3024F 66FLR3024F 3.00 3.465 76.0 1.53 65FLR3030F 66FLR3030F 3.38 5.280 86.0 2.44 65FLR3040F 66FLR3040F 4.00 10.0

100 102.0 4.55 65FLR3050F 66FLR3050F 5.00 13.2

125 127.0 6.06 65FLR3060F 66FLR3060F 5.50 18.1

150 140.0 8.28 65FLR3080F 66FLR3080F 7.25 35.0

200 184.0 15.910 65FLR3100F 66FLR3100F 8.50 59.0250 216.0 26.812 65FLR3120F 66FLR3120F 10.00 102.0300 254.0 46.414 65FLR3140F 66FLR3140F 8.75 122.0350 222.0 55.516 65FLR3160F 66FLR3160F 10.00 134.0400 254.0 60.918 65FLR3180F 66FLR3180F 11.25 133.0450 286.0 60.520 65FLR3200F 66FLR3200F 12.50 165.0500 318.0 75.024 65FLR3240F 66FLR3240F 15.00 237.0600 381.0 107.7



Fig. 65Y & 66YTrue Wye• (F) Fabricated steel fittings – all sizes


Fig. 65LY & 66LY45° Lateral• (F) Fabricated steel fittings – all sizes


Grooved Wye & Lateral Fittings

SE

LE

SCI

LE

LE

SE

SCI

LE SE

Pipe Size Part Number LE SE Weightin / mm Painted Galvanized in / mm in / mm lb / kg

1 65Y3010F 66Y3010F 2.75 2.50 1.025 70.0 64.0 0.5

1-1/4 65Y3012F 66Y3012F 2.75 2.50 1.532 70.0 64.0 0.7

1-1/2 65Y3014F 66Y3014F 2.75 2.75 1.840 70.0 70.0 0.82 65Y3020F 66Y3020F 3.25 2.75 2.450 83.0 70.0 1.1

2-1/2 65Y3024F 66Y3024F 3.75 3.00 4.965 95.0 76.0 2.23 65Y3030F 66Y3030F 4.25 3.25 5.980 108.0 83.0 2.84 65Y3040F 66Y3040F 5.00 3.75 10.2

100 127.0 95.0 4.55 65Y3050F 66Y3050F 5.50 4.00 14.7

125 140.0 102.0 6.86 65Y3060F 66Y3060F 6.50 4.50 20.2

150 165.0 114.0 9.28 65Y3080F 66Y3080F 7.75 6.00 34.5

200 197.0 152.0 15.710 65Y3100F 66Y3100F 9.00 6.50 48.0250 229.0 165.0 21.812 65Y3120F 66Y3120F 10.00 7.00 84.8300 254.0 178.0 38.514 65Y3140F 66Y3140F 11.00 7.50 101.0350 279.0 191.0 45.916 65Y3160F 66Y3160F 12.00 8.00 125.0400 305.0 203.0 56.818 65Y3180F 66Y3180F 15.50 8.50 180.0450 394.0 216.0 81.820 65Y3200F 66Y3200F 17.25 9.00 217.0500 438.0 229.0 98.624 65Y3240F 66Y3240F 20.00 10.00 298.0600 508.0 254.0 135.5

Pipe Size Part Number LE SE Weightin / mm Painted Galvanized in / mm in / mm lb / kg

1 65LY3010F 66LY3010F 5.00 2.25 1.525 127.0 57.0 0.7

1-1/4 65LY3012F 66LY3012F 5.75 2.50 2.232 146.0 64.0 1.0

1-1/2 65LY3014F 66LY3014F 6.25 2.75 3.240 159.0 70.0 1.52 65LY3020F 66LY3020F 7.00 2.75 4.450 178.0 70.0 2.0

2-1/2 65LY3024F 66LY3024F 7.75 3.00 9.865 197.0 76.0 4.53 65LY3030F 66LY3030F 8.50 3.25 11.080 216.0 83.0 5.04 65LY3040F 66LY3040F 10.50 3.75 18.0

100 267 95.0 8.25 65LY3050F 66LY3050F 12.50 4.00 28.5

125 318.0 102.0 13.06 65LY3060F 66LY3060F 14.00 4.50 39.0

150 356.0 114.0 17.78 65LY3080F 66LY3080F 18.00 6.00 81.8

200 457.0 152.0 37.210 65LY3100F 66LY3100F 20.50 6.50 127.0250 521.0 165.0 57.712 65LY3120F 66LY3120F 23.00 7.00 157.0300 584.0 178.0 71.414 65LY3140F 66LY3140F 26.50 7.50 201.0350 673.0 191.0 91.416 65LY3160F 66LY3160F 29.00 8.00 340.0400 737.0 203.0 154.518 65LY3180F 66LY3180F 32.00 8.50 420.0450 813.0 216.0 190.920 65LY3200F 66LY3200F 35.00 9.00 515.0500 889.0 229.0 234.124 65LY3240F 66LY3240F 40.00 10.00 930.0600 1016.0 254.0 422.7



Fig. 65ES & 66ES 90° Elbow, Short Radius• Ductile Iron - Full Flow

Fig. 65TS & 66TS Tee, Short Radius• Ductile Iron - Full Flow

Fig. 65DC & 66DCDrain Cap• Ductile Iron• 1” NPT drain

Fig. 65DE & 66DE Drain Elbow – Standard Radius• Ductile Iron - Full Flow• 1” NPT drain

Short Radius Fittings & Drain Fittings

A

A

A

A

A

1" NPTDRAIN

A

C

B 1" NPT DRAIN



2 65ES3020 66ES3020 2.75 26 1.550 69.9 0.7

2-1/2 65ES3024 66ES3024 3.00 16 2.065 76.2 0.93 65ES3030 66ES3030 3.38 20 2.980 85.9 1.34 65ES3040 66ES3040 4.00 12 4.6

100 101.6 2.16 65ES3060 66ES3060 5.50 - 11.4

150 139.7 5.28 65ES3080 66ES3080 6.81 - 22.7

200 173.0 10.3



2 65TS3020 66TS3020 2.75 16 2.150 69.9 0.9

2-1/2 65TS3024 66TS3024 3.00 12 2.865 76.2 1.33 65TS3030 66TS3030 3.38 12 4.180 85.9 1.94 65TS3040 66TS3040 4.00 8 6.6

100 101.6 3.06 65TS3060 66TS3060 5.50 - 11.1

150 139.7 5.08 65TS3080 66TS3080 6.94 - 16.8

200 176.3 7.6



2 65DC3020 66DC3020 0.88 80 0.750 22.4 0.3

2-1/2 65DC3024 66DC3024 0.88 60 0.865 22.4 0.43 65DC3030 66DC3030 0.88 40 1.380 22.4 0.64 65DC3040 66DC3040 1.00 24 2.1

100 25.4 0.95 65DC3050 66DC3050 1.00 12 3.5

125 25.4 1.66 65DC3060 66DC3060 1.00 10 4.9

150 25.4 2.28 65DC3080 66DC3080 1.20 5 10.1

200 30.5 4.6

Pipe Size Part Number A B C Case Qty

Weightin / mm Painted Galvanized in / mm in / mm in / mm lb / kg

2 65DE3020 66DE3020 3.25 2.76 1.30 20 1.850 82.6 70.0 33.0 0.8

2-1/2 65DE3024 66DE3024 3.75 2.76 1.68 12 2.665 95.3 70.0 42.7 1.23 65DE3030 66DE3030 4.25 2.76 2.10 15 3.780 108.0 70.0 53.3 1.74 65DE3040 66DE3040 5.00 2.76 2.60 8 5.9

100 127.0 70.0 66.0 2.76 65DE3060 66DE3060 6.50 2.76 3.65 - 13.9

150 165.1 70.0 92.7 6.38 65DE3080 66DE3080 7.75 2.76 4.57 - 26.6

200 196.9 70.0 116.1 12.1



Fig. 65MT & 66MT Mechanical Tee, Threaded• Maximum working pressure 500 psi (34.5 bar) depending on size and

schedule of pipe• ASME B1.20.1 NPT Threads• Equivalent length in feet of Schedule 40 outlet pipe with a Hazen-Williams

coefficient of 120 per UL 213 • All housings, gaskets and bolts identified by SCI logo • 100% Magnetic Particle inspection of each Bolt• Each bolt has a minimum tensile strength of 110,000 psi • Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Ductile iron housings conform to ASTM A-536 • Smith-Cooper Warranty only applies to assemblies made with housings,


Mechanical Tee, Threaded

SizeRun x Branch

Part Number Hole Diameter Dimensions Equivalent Length in

Feet

Case Qty

WeightPainted Galvanized

+1/8, -0 / +3.2, -0 A B Cin / mm in / mm in / mm in / mm in / mm lb / kg2 x 1/2 65MT3020004 66MT3020004 1-1/2 2.50 4.96 2.80 - 21 2.050 x 15 38 64.0 126.0 71.1 0.92 x 3/4 65MT3020006 66MT3020006 1-1/2 2.50 4.96 2.80 - 21 2.050 x 20 38 64.0 126.0 71.1 0.92 x 1 65MT3020010 66MT3020010 1-1/2 2.50 4.96 2.80 2 21 2.1

50 x 25 38 64.0 126.0 71.1 1.02 x 1-1/4 65MT3020012 66MT3020012 1-3/4 2.80 4.96 2.80 4 18 2.2

50 x 32 45 70.1 126.0 71.1 1.02 x 1-1/2 65MT3020014 66MT3020014 1-3/4 2.80 4.96 2.87 9 18 2.2

50 x 40 45 70.1 126.0 72.9 1.02-1/2 x 1/2 65MT3024004 66MT3024004 1-1/2 2.80 5.20 2.80 - 18 2.2

65 x 15 38 70.1 132.1 71.1 1.02-1/2 x 3/4 65MT3024006 66MT3024006 1-1/2 2.80 5.20 2.80 - 18 2.4

65 x 20 38 70.1 132.1 71.1 1.12-1/2 x 1 65MT3024010 66MT3024010 1-1/2 2.80 5.20 2.80 2 18 2.6

65 x 25 38 70.1 132.1 71.1 1.22-1/2 x 1-1/4 65MT3024012 66MT3024012 1-3/4 3.00 5.20 3.03 4 16 2.8

65 x 32 45 75.9 132.1 77.0 1.32-1/2 x 1-1/2 65MT3024014 66MT3024014 2 3.00 5.20 3.27 9 16 3.0

65 x 40 51 75.9 132.1 83.1 1.43 x 1 65MT3030010 66MT3030010 1-1/2 3.10 5.91 2.80 2 14 2.6

80 x 25 38 78.0 150.1 71.1 1.23 x 1-1/4 65MT3030012 66MT3030012 1-3/4 3.27 5.91 3.03 4 14 2.9

80 x 32 45 83.1 150.1 77.0 1.33 x 1-1/2 65MT3030014 66MT3030014 2 3.50 5.91 3.27 3 14 3.1

80 x 40 51 88.9 150.1 83.1 1.43 x 2 65MT3030020 66MT3030020 2-1/2 3.50 5.91 3.78 5 10 3.5

80 x 50 64 88.9 150.1 96.0 1.64 x 1 65MT3040010 66MT3040010 1-1/2 3.54 7.09 2.80 2 22 3.0

100 x 25 38 89.9 180.1 71.1 1.34 x 1-1/4 65MT3040012 66MT3040012 1-3/4 3.78 7.09 3.03 4 22 3.2100 x 32 45 96.0 180.1 77.0 1.44 x 1-1/2 65MT3040014 66MT3040014 2 4.02 7.09 3.27 3 22 3.4100 x 40 51 102.1 180.1 83.1 1.6

B

4" x 3"

65MTA

C


Mechanical Tee, Threaded (cont.)

SizeRun x Branch


Feet

Case Qty


+1/8, -0 / +3.2, -0 A B Cin / mm in / mm in / mm in / mm in / mm lb / kg4 x 2 65MT3040020 66MT3040020 2-1/2 4.02 7.24 3.94 5 14 4.4

100 x 50 64 102.1 183.9 100.1 2.04 x 2-1/2 65MT3040024 66MT3040024 2-3/4 4.02 7.24 4.21 11 14 4.9100 x 65 70 102.1 183.9 106.9 2.2

4 x 3 65MT3040030 66MT3040030 3-1/2 4.53 7.24 4.76 13 12 6.1100 x 80 89 115.1 183.9 120.9 2.85 x 1-1/4 65MT3050012 66MT3050012 1-3/4 4.76 7.99 3.03 4 12 4.1125 x 32 45 120.9 202.9 77.0 1.95 x 1-1/2 65MT3050014 66MT3050014 2 4.76 7.99 3.27 3 12 4.2125 x 40 51 120.9 202.9 83.1 1.9

5 x 2 65MT3050020 66MT3050020 2-1/2 4.76 8.66 3.94 5 8 6.0125 x 50 64 120.9 220.0 100.1 2.75 x 2-1/2 65MT3050024 66MT3050024 2-3/4 4.76 8.66 4.21 11 8 6.6125 x 65 70 120.9 220.0 106.9 3.0

5 x 3 65MT3050030 66MT3050030 3-1/2 5.00 8.66 4.92 13 8 7.5125 x 80 89 127.0 220.0 125.0 3.46 x 1-1/4 65MT3060012 66MT3060012 1-3/4 5.12 9.13 3.03 4 12 4.4150 x 32 45 130.0 231.9 77.0 2.06 x 1-1/2 65MT3060014 66MT3060014 2 5.12 9.13 3.27 3 12 4.5150 x 40 51 130.0 231.9 83.1 2.0

6 x 2 65MT3060020 66MT3060020 2-1/2 5.12 9.76 3.94 5 8 6.5150 x 50 64 130.0 247.9 100.1 3.06 x 2-1/2 65MT3060024 66MT3060024 2-3/4 5.12 9.76 4.21 11 8 6.8150 x 65 70 130.0 247.9 106.9 3.1

6 x 3 65MT3060030 66MT3060030 3-1/2 5.51 9.76 4.92 13 8 7.9150 x 80 89 140.0 247.9 125.0 3.6

6 x 4 65MT3060040 66MT3060040 4-1/2 5.75 9.76 5.91 15 6 9.6150 x 100 114 146.1 247.9 150.1 4.4

8 x 2 65MT3080020 66MT3080020 2-1/2 6.26 11.81 3.94 5 6 8.2200 x 50 64 159.0 300.0 100.1 3.78 x 2-1/2 65MT3080024 66MT3080024 2-3/4 6.26 11.81 4.21 11 6 8.6200 x 65 70 159.0 300.0 106.9 3.9

8 x 3 65MT3080030 66MT3080030 3-1/2 6.50 11.81 4.92 13 6 9.3200 x 80 89 165.1 300.0 125.0 4.2

8 x 4 65MT3080040 66MT3080040 4-1/2 6.73 11.81 5.91 15 4 10.7200 x 100 114 170.9 300.0 150.1 4.9

Fig. 65MT & 66MT Mechanical Tee, Threaded• Maximum working pressure 500 psi (34.5 bar) depending on size and

schedule of pipe• ASME B1.20.1 NPT threads• Equivalent length in feet of schedule 40 outlet pipe with a Hazen-Williams

coefficient of 120 per UL 213 • All housings, gaskets and bolts identified by SCI logo • 100% magnetic particle inspection of each bolt• Each bolt has a minimum tensile strength of 110,000 psi • Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Ductile iron housings conform to ASTM A-536 • Smith-Cooper Warranty only applies to assemblies made with housings,

gaskets and bolts carrying the logo B

4" x 3"

65MTA

C


Fig. 65MG & 66MGMechanical Tee, Grooved• Maximum working pressure 500 psi (34.5 bar) depending on size

and schedule of pipe • Equivalent length in feet of schedule 40 outlet pipe with a

Hazen-Williams coefficient of 120 per UL 213 • All housings, gaskets and bolts identified by SCI logo• Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Ductile iron housings conform to ASTM A-536 • Groove dimensions to AWWA C-606 • Smith-Cooper Warranty only applies to assemblies made with


Mechanical Tee, Grooved

SizeRun x Branch


Feet

Case Qty


+1/8, -0 / +3.2, -0 A B Cin / mm in / mm in / mm in / mm in / mm lb / kg

3 x 1-1/4 65MG3030012 66MG3030012 1-3/4 3.50 5.90 3.03 4 14 3.080 x 32 45 89.9 150.1 77.0 1.4

3 x 1-1/2 65MG3030014 66MG3030014 2 3.50 5.90 3.30 3 14 3.180 x 40 51 89.9 150.1 83.1 1.43 x 2 65MG3030020 66MG3030020 2-1/2 3.50 5.90 3.80 5 10 3.6

80 x 50 64 89.9 150.1 96.0 1.64 x 1-1/4 65MG3040012 66MG3040012 1-3/4 4.00 7.10 3.03 4 22 3.2100 x 40 45 102.1 180.1 77.0 1.44 x 1-1/2 65MG3040014 66MG3040014 2 4.00 7.10 3.30 3 22 4.3100 x 40 51 102.1 180.1 83.1 1.9

4 x 2 65MG3040020 66MG3040020 2-1/2 4.02 7.24 3.94 5 14 4.4100 x 50 64 102.1 183.9 100.1 2.04 x 2-1/2 65MG3040024 66MG3040024 2-3/4 4.02 7.24 4.21 11 14 4.9100 x 65 70 102.1 183.9 106.9 2.2

4 x 3 65MG3040030 66MG3040030 3-1/2 4.53 7.24 4.76 13 12 6.1100 x 80 89 115.1 183.9 120.9 2.85 x 1-1/2 65MG3050014 66MG3050014 2 4.76 7.99 3.27 3 12 4.2125 x 40 51 120.9 202.9 83.1 1.9

5 x 2 65MG3050020 66MG3050020 2-1/2 4.76 8.66 3.94 5 8 6.0125 x 50 64 120.9 220.0 100.1 2.75 x 2-1/2 65MG3050024 66MG3050024 2-3/4 4.76 8.66 4.21 11 8 6.6125 x 65 70 120.9 220.0 106.9 3.0

5 x 3 65MG3050030 66MG3050030 3-1/2 5.00 8.66 4.92 13 8 7.5125 x 80 89 127.0 220.0 125.0 3.46 x 1-1/4 65MG3060012 66MG3060012 1-3/4 5.12 9.13 3.03 4 12 4.4150 x 32 45 130.0 231.9 77.0 2.06 x 1-1/2 65MG3060014 66MG3060014 2 5.12 9.13 3.27 3 12 4.5150 x 40 51 130.0 231.9 83.1 2.0

6 x 2 65MG3060020 66MG3060020 2-1/2 5.12 9.76 3.94 5 8 6.5150 x 50 64 130.0 247.9 100.1 3.06 x 2-1/2 65MG3060024 66MG3060024 2-3/4 5.12 9.76 4.21 11 8 6.8150 x 65 70 130.0 247.9 106.9 3.1

6 x 3 65MG3060030 66MG3060030 3-1/2 5.51 9.76 4.92 13 8 7.9150 x 80 89 140.0 247.9 125.0 3.6

6 x 4 65MG3060040 66MG3060040 4-1/2 5.75 9.76 5.91 15 6 9.6150 x 100 114 146.1 247.9 150.1 4.4

8 x 2 65MG3080020 66MG3080020 2-1/2 6.26 11.81 3.94 5 6 8.2200 x 50 64 159.0 300.0 100.1 3.78 x 2-1/2 65MG3080024 66MG3080024 2-3/4 6.26 11.81 4.21 11 6 8.6200 x 65 70 159.0 300.0 106.9 3.9

8 x 3 65MG3080030 66MG3080030 3-1/2 6.50 11.81 4.92 13 6 9.3200 x 80 89 165.1 300.0 125.0 4.2

8 x 4 65MG3080040 66MG3080040 4-1/2 6.73 11.81 5.91 15 4 10.7200 x 100 114 170.9 300.0 150.1 4.9

B

4" x 3"

65MG

A

C


Fig. 65MU & 66MU Strap Tee, Threaded• Maximum working pressure 300 psi (20.7 bar) depending on size and

schedule of pipe• ASME B1.20.1 NPT threads• Equivalent length in feet of schedule 40 outlet pipe with a Hazen-Williams

coefficient of 120 per UL 213 • 1” outlets not listed by UL for direct connection to 1” sprinkler heads • Gasket Grade E - EPDM (green stripe) -30˚F (-34˚C) to +230˚F (+110˚C) • Ductile iron housings conform to ASTM A-536 • Smith-Cooper Warranty only applies to assemblies made with housings,


Strap Tee, Threaded

SizeRun x Branch


Feet

Case Qty


+1/8, -0 / +3.2, -0 A B Cin / mm in / mm in / mm in / mm in / mm lb / kg

1-1/4 x 1/2 65MU3012004 66MU3012004 1-1/4 1.65 3.54 2.28 - 50 0.832 x 15 32 41.9 89.9 57.9 0.4

1-1/4 x 3/4 65MU3012006 66MU3012006 1-1/4 1.85 3.54 2.28 - 50 0.932 x 20 32 47.0 89.9 57.9 0.4

1-1/4 x 1 65MU3012010 66MU3012010 1-1/4 2.13 3.54 2.28 5 50 1.032 x 25 32 54.1 89.9 57.9 0.5

1-1/2 x 1/2 65MU3014004 66MU3014004 1-1/4 1.77 3.54 2.28 - 48 0.840 x 15 32 45.0 89.9 57.9 0.4

1-1/2 x 3/4 65MU3014006 66MU3014006 1-1/4 1.97 3.54 2.28 - 48 0.940 x 20 32 50.0 89.9 57.9 0.4

1-1/2 x 1 65MU3014010 66MU3014010 1-1/4 2.24 3.54 2.28 5 48 1.040 x 25 32 56.9 89.9 57.9 0.52 x 1/2 65MU3020004 66MU3020004 1-1/4 2.01 3.74 2.28 - 45 0.850 x 15 32 51.1 95.0 57.9 0.42 x 3/4 65MU3020006 66MU3020006 1-1/4 2.20 3.74 2.28 - 45 0.950 x 20 32 55.9 95.0 57.9 0.42 x 1 65MU3020010 66MU3020010 1-1/4 2.48 3.74 2.28 5 45 1.0

50 x 25 32 63.0 95.0 57.9 0.52-1/2 x 1/2 65MU3024004 66MU3024004 1-1/4 2.26 4.29 2.28 - 36 1.0

65 x 15 32 57.4 109.0 57.9 0.52-1/2 x 3/4 65MU3024006 66MU3024006 1-1/4 2.50 4.29 2.30 - 36 1.1

65 x 20 32 62.5 109.0 57.9 0.52-1/2 x 1 65MU3024010 66MU3024010 1-1/4 2.70 4.29 2.30 5 36 1.2

65 x 25 32 69.6 109.0 57.9 0.5

B

A

C


COOPLET® Weld Outlets & Adapter Nipples

Pipe Name Manufacturers

Dyna- Thread®, Central- Thread®, XL® , XL-II® , Dyna-Flow®, Super 40®, Super- Flo®, TL®, Central 7 ®, BLT ® Allied Tube and Conduit Corp.

Eddylite®, Eddy Flow®, Eddy Thread 40® Bull Moose Tube Co.

Gal-7® IDOD Systems Co.

EZ-Flow® Northwest Pipe Company

WLS®, Mega Flow®, Mega- Thread®, MLT®, GL® Wheatland Tube Company

Steady Flow®, Steady Thread® Welded Tube Corp.

Fire-Flo®, Ez- Thread® Youngstown Tube Co.

Tex- Flow® Tex- Tube International

Fire Line Flow®, Rapid Thread®, Rapid-Thread Light® Western International Forest Products Inc.

COOPLET® Weld Outlets are UL Listed and FM Approved for use on Sch 10, Sch 40 and the following sprinkler pipe

Weld Outlet Specifi cations

• Branded COOPLET® Weld Outlets are UL Listed and FM Approved at 300 psi

• COOPLET® Weld Outlets (Th readed) conform to ASTM A106, ASME B1.20.1

• COOPLET® Grooved Weld Outlets are made from Sch. 40 Pipe

• COOPLET® Grooved Weld Outlets size-on-size are UL Listed Only

• All Grooves are cut grooved per AWWA C606

COOPLET® Weld Outlets & Adapter Nipples

Adapter Nipple Specifi cations• COOPLET® Adapter Nipples conform to ASTM A106, ASME B1.20.1, ASME B36.10, and

AWWA C606

• All grooves are cut grooved per AWWA 606


COOPLETS®

A

Sizein

Pipe Run Size

Part NumberAin

Cin


1/2 1 to 1-1/2 61FT1004010 1.063 0.750 50 400 0.11/2 2 to 2-1/2 61FT1004020 1.063 0.750 50 400 0.11/2 3 to 8 61FT1004030 1.063 0.750 50 400 0.13/4 1 to 1-1/2 61FT1006010 1.125 0.875 50 300 0.23/4 2 to 2-1/2 61FT1006020 1.125 0.875 50 300 0.23/4 2-1/2 61FT1006024 1.125 0.875 50 300 0.23/4 3 to 8 61FT1006030 1.125 0.875 50 300 0.21 1-1/4 61FT1010012 1.250 1.125 50 200 0.21 1-1/2 61FT1010014 1.250 1.125 50 200 0.21 2 to 2-1/2 61FT1010020 1.250 1.125 50 200 0.21 2-1/2 61FT1010024 1.250 1.125 50 200 0.21 3 to 4 61FT1010030 1.250 1.125 50 200 0.21 5 to 8 61FT1010060 1.250 1.125 50 200 0.2

1-1/4 1-1/2 61FT1012014 1.375 1.500 70 140 0.31-1/4 2 61FT1012020 1.375 1.500 70 140 0.31-1/4 2-1/2 61FT1012024 1.375 1.500 70 140 0.31-1/4 3 to 4 61FT1012030 1.375 1.500 70 140 0.31-1/4 5 to 8 61FT1012060 1.375 1.500 70 140 0.31-1/2 2 61FT1014020 1.625 1.625 50 100 0.51-1/2 2-1/2 61FT1014024 1.625 1.625 50 100 0.51-1/2 3 61FT1014030 1.625 1.625 50 100 0.51-1/2 4 to 5 61FT1014040 1.625 1.625 50 100 0.51-1/2 6 to 8 61FT1014060 1.625 1.625 50 100 0.5

2 2-1/2 61FT1020024 1.750 2.000 25 50 0.82 3 61FT1020030 1.750 2.000 25 50 0.82 4 to 5 61FT1020040 1.750 2.000 25 50 0.82 6 to 8 61FT1020060 1.750 2.000 25 50 0.8

2-1/2 3 61FT1024030 2.215 2.500 15 30 1.42-1/2 4 61FT1024040 2.215 2.500 15 30 1.42-1/2 6 61FT1024060 2.215 2.500 15 30 1.42-1/2 8 61FT1024080 2.215 2.500 15 30 1.4

3 4 61FT1030040 2.500 3.000 8 16 2.43 6 61FT1030060 2.500 3.000 8 16 2.33 8 61FT1030080 2.500 3.000 8 16 2.34 6 61FT1040060 3.000 4.000 4 8 4.14 8 61FT1040080 3.000 4.000 4 8 4.0

Fig. 61FT1 – Threaded Weld Outlet

C

COOPLET® Threaded Weld Outlets - 300#


COOPLETS®

Sizein

Pipe Run Size

Part NumberAin

Cin


1-1/4 1-1/2 61CG1012014 3.00 1.38 40 80 0.51-1/4 2 61CG1012020 3.00 1.38 40 80 0.51-1/4 2-1/2 61CG1012024 3.00 1.38 40 80 0.51-1/4 3 61CG1012030 3.00 1.38 40 80 0.51-1/4 4 to 5 61CG1012040 3.00 1.38 40 80 0.51-1/4 6 to 8 61CG1012060 3.00 1.38 40 80 0.51-1/2 2 61CG1014020 3.00 1.61 25 50 0.61-1/2 2-1/2 61CG1014024 3.00 1.61 25 50 0.61-1/2 3 61CG1014030 3.00 1.61 25 50 0.61-1/2 4 to 5 61CG1014040 3.00 1.61 25 50 0.61-1/2 6 to 8 61CG1014060 3.00 1.61 25 50 0.6

2 2-1/2 61CG1020024 3.00 2.00 16 32 0.82 3 61CG1020030 3.00 2.00 16 32 0.82 4 to 5 61CG1020040 3.00 2.00 16 32 0.82 6 61CG1020060 3.00 2.00 16 32 0.82 8 61CG1020080 3.00 2.00 16 32 0.8

2-1/2 3 61CG1024030 3.00 2.50 12 24 1.32-1/2 4 to 5 61CG1024040 3.00 2.50 12 24 1.32-1/2 6 61CG1024060 3.00 2.50 12 24 1.32-1/2 8 61CG1024080 3.00 2.50 12 24 1.3

3 4 61CG1030040 3.00 3.00 6 12 1.83 6 61CG1030060 3.00 3.00 6 12 1.83 8 61CG1030080 3.00 3.00 6 12 1.74 6 61CG1040060 4.00 4.00 4 8 3.54 8 61CG1040080 4.00 4.00 4 8 3.46 8 61CG1060080 4.00 6.00 - 2 6.5

Fig. 61CG1 – Grooved Weld Outlet

A

C

*All Grooves are Cut Grooved

(Cut grooved specifi cations on page XX)

Sizein

Pipe Run Size

Part NumberAin

Cin


1-1/4 1-1/4 61CG1012012 3.00 1.38 40 80 0.51-1/2 1-1/2 61CG1014014 3.00 1.61 25 50 0.6

2 2 61CG1020020 3.00 2.00 16 32 0.82-1/2 2-1/2 61CG1024024 3.00 2.50 12 24 1.3

3 3 61CG1030030 3.00 3.00 6 12 1.84 4 61CG1040040 4.00 4.00 4 8 3.56 6 61CG1060060 4.00 6.00 - 2 6.58 8 61CG1080080 4.00 8.00 - 2 11.6

Fig. 61CG1 – Grooved Weld Outlet (size on size)*

*Size on Size Grooved Weld Outlets are UL Listed Only

COOPLET® Grooved Weld Outlets - 300#


COOPLETS®

Sizein Part Number

Ain

Bin TPI Master

Weightlb

1 x 4 61TG4010040 4.00 1.32 11.5 100 0.51-1/4 x 4 61TG4012040 4.00 1.66 11.5 50 0.61-1/2 x 4 61TG4014040 4.00 1.90 11.5 50 0.7

1-1/2 x 12 61TG4014120 12.00 1.90 11.5 15 2.62 x 3 61TG4020030 3.00 2.38 11.5 50 0.72 x 4 61TG4020040 4.00 2.38 11.5 25 1.02 x 6 61TG4020060 6.00 2.38 11.5 25 1.72 x 8 61TG4020080 8.00 2.38 11.5 18 2.32 x 10 61TG4020100 10.00 2.38 11.5 14 2.92 x 12 61TG4020120 12.00 2.38 11.5 14 3.5

2-1/2 x 4 61TG4024040 4.00 2.88 8.0 27 1.62-1/2 x 12 61TG4024120 12.00 2.88 8.0 9 5.53 x 2-5/8 61TG4030025 2.62 3.50 8.0 24 1.3

3 x 3 61TG4030030 3.00 3.50 8.0 24 1.53 x 4 61TG4030040 4.00 3.50 8.0 18 2.13 x 6 61TG4030060 6.00 3.50 8.0 12 3.43 x 8 61TG4030080 8.00 3.50 8.0 8 4.73 x 10 61TG4030100 10.00 3.50 8.0 6 5.93 x 12 61TG4030120 12.00 3.50 8.0 6 7.24 x 3 61TG4040030 3.00 4.50 8.0 12 1.64 x 4 61TG4040040 4.00 4.50 8.0 12 2.64 x 6 61TG4040060 6.00 4.50 8.0 8 4.94 x 8 61TG4040080 8.00 4.50 8.0 5 6.74 x 10 61TG4040100 10.00 4.50 8.0 4 8.54 x 12 61TG4040120 12.00 4.50 8.0 4 10.35 x 6 61TG4050060 6.00 5.56 8.0 2 6.65 x 12 61TG4050120 12.00 5.56 8.0 1 13.96 x 6 61TG4060060 6.00 6.63 8.0 2 8.66 x 12 61TG4060120 12.00 6.63 8.0 1 18.18 x 6 61TG4080060 6.00 8.63 8.0 1 13.28 x 12 61TG4080120 12.00 8.63 8.0 1 27.5

A

B

Sizein Part Number

Ain

Bin TPI Master

Weightlb

2 x 3 61TG8020030 3.00 2.38 11.5 50 1.12 x 4 61TG8020040 4.00 2.38 11.5 25 1.52 x 6 61TG8020060 6.00 2.38 11.5 25 2.32 x 8 61TG8020080 8.00 2.38 11.5 18 3.2

2 x 10 61TG8020100 10.00 2.38 11.5 12 4.02 x 12 61TG8020120 12.00 2.38 11.5 12 4.9

3 x 2-5/8 61TG8030025 2.62 3.50 8.0 24 1.93 x 3 61TG8030030 3.00 3.50 8.0 24 2.23 x 4 61TG8030040 4.00 3.50 8.0 18 3.03 x 6 61TG8030060 6.00 3.50 8.0 12 4.73 x 8 61TG8030080 8.00 3.50 8.0 8 6.5

3 x 10 61TG8030100 10.00 3.50 8.0 6 8.23 x 12 61TG8030120 12.00 3.50 8.0 6 9.94 x 3 61TG8040030 3.00 4.50 8.0 12 3.24 x 4 61TG8040040 4.00 4.50 8.0 12 4.54 x 6 61TG8040060 6.00 4.50 8.0 8 7.04 x 8 61TG8040080 8.00 4.50 8.0 5 9.5

4 x 10 61TG8040100 10.00 4.50 8.0 4 12.04 x 12 61TG8040120 12.00 4.50 8.0 4 14.5

Fig. 61TG8 – Schedule 80 Threaded x Grooved Adapter Nipple

Fig. 61TG4 – Schedule 40 Threaded x Grooved Adapter Nipple

COOPLET® Adapter Nipples


COOPLETS®

A

B

Sizein Part Number

Ain

Bin Master

Weightlb

2 x 3 61GG4020030 3.00 2.38 50 0.82 x 4 61GG4020040 4.00 2.38 50 1.12 x 6 61GG4020060 6.00 2.38 25 1.72 x 8 61GG4020080 8.00 2.38 18 2.3

2 x 10 61GG4020100 10.00 2.38 14 2.92 x 12 61GG4020120 12.00 2.38 14 3.5

3 x 2-5/8 61GG4030025 2.62 3.50 24 1.53 x 3 61GG4030030 3.00 3.50 24 1.73 x 4 61GG4030040 4.00 3.50 18 2.43 x 6 61GG4030060 6.00 3.50 12 3.63 x 8 61GG4030080 8.00 3.50 8 4.9

3 x 10 61GG4030100 10.00 3.50 6 6.23 x 12 61GG4030120 12.00 3.50 6 7.44 x 3 61GG4040030 3.00 4.50 12 2.44 x 4 61GG4040040 4.00 4.50 12 3.34 x 6 61GG4040060 6.00 4.50 8 5.14 x 8 61GG4040080 8.00 4.50 5 6.9

4 x 10 61GG4040100 10.00 4.50 4 8.74 x 12 61GG4040120 12.00 4.50 4 10.3

Sizein Part Number

Ain

Bin Master

Weightlb

2 x 3 61GG8020030 3.00 2.38 50 1.12 x 4 61GG8020040 4.00 2.38 25 1.52 x 6 61GG8020060 6.00 2.38 25 2.42 x 8 61GG8020080 8.00 2.38 18 3.2

2 x 10 61GG8020100 10.00 2.38 12 4.12 x 12 61GG8020120 12.00 2.38 12 4.9

3 x 2-5/8 61GG8030025 2.62 3.50 24 2.13 x 3 61GG8030030 3.00 3.50 24 2.43 x 4 61GG8030040 4.00 3.50 18 3.33 x 6 61GG8030060 6.00 3.50 12 5.03 x 8 61GG8030080 8.00 3.50 8 6.7

3 x 10 61GG8030100 10.00 3.50 6 8.43 x 12 61GG8030120 12.00 3.50 6 10.14 x 3 61GG8040030 3.00 4.50 12 3.44 x 4 61GG8040040 4.00 4.50 12 4.74 x 6 61GG8040060 6.00 4.50 8 7.24 x 8 61GG8040080 8.00 4.50 5 9.7

4 x 10 61GG8040100 10.00 4.50 4 12.24 x 12 61GG8040120 12.00 4.50 4 14.7

Fig. 61GG4 – Schedule 40 Grooved x Grooved Adapter Nipple

Fig. 61GG8 – Schedule 80 Grooved x Grooved Adapter Nipple



COOPLETS®

A

B

Sizein Part Number

Ain

Bin Master

Weightlb

1 x 3 61GB4010030 3.00 1.32 150 0.31 x 4 61GB4010040 4.00 1.32 100 0.5

1-1/4 x 4 61GB4012040 4.00 1.66 50 0.61-1/2 x 4 61GB4014040 4.00 1.90 50 0.7

2 x 4 61GB4020040 4.00 2.38 25 1.12-1/2 x 4 61GB4024040 4.00 2.88 27 1.6

3 x 4 61GB4030040 4.00 3.50 18 2.44 x 6 61GB4040060 6.00 4.50 8 5.15 x 6 61GB4050060 6.00 5.56 2 6.66 x 6 61GB4060060 6.00 6.63 2 8.68 x 6 61GB4080060 6.00 8.63 2 13.2

Fig. 61GG4 – Schedule 40 Grooved x Bevel Adapter Nipple

Bevel 37-1/2°


SECTION 4

VALVES

FIVALCO GROOVED BUTTERFLY VALVES [OR EQUAL]

FIVALCO GROOVED CHECK VALVES [OR EQUAL]

RELIABLE COMMERCIAL RISER MANIFOLD [OR EQUAL]

Kyle.Montgomery

Image

Kyle.Montgomery

Image

Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523

Bulletin 617 R

ev. DBulletin 617 Rev. D

Available Sizes/Pressure Ratings:

11/2”(40mm) and 2”(50mm) Threaded - 250 psi (17,2 bar) Working Pressure

2”(50mm), 21/2”(65mm), & 3”(80mm) Grooved - 300 psi (20,7 bar) Working Pressure

4”(100mm), 6”(150mm), & 8”(200mm) Grooved - 300 psi (20,7 bar) Working Pressure

Model CR Commercial RiserRiser Manifold for Commercial Applications

Features 1. Cast stainless steel body construction for threaded

manifolds.2. Painted, cast ductile iron body construction for grooved

manifolds.3. Brass and galvanized Trim.4. Factory assembled and pressure tested.5. Available with Test and Drain Valves in various orifice

sizes. Grooved end Test and Drain valves are available as MTO.

6. Optional Pressure Relief Valve Kit available for all sizes.7. Same take-out dimensions for the 11/2”(40mm) and

2”(50mm) threaded sizes.8. Same end-to-end dimensions for the 2”(50mm) through

8”(200mm) grooved sizes.9. Approved for installation in horizontal or vertical posi-

tions.10. Built in drain port allows hydrostatic testing without

draining the system.11. ¼” three-way valve allows for easy testing and replacing

of pressure gauge.12. Dedicated cULus Listed, ULC Listed and FM Approved

Waterflow Detector assures optimum sensitivity. See Table 3 for triggering flow rates.

Product DescriptionThe Model CR Commercial Riser comes factory assem-

bled with the necessary accessories for a cost effective, yet complete riser assembly. These assemblies are UL Listed, ULC Listed and FM Approved as a unit.

Cast-on lettering on the manifold identifies manifold pipe size, flow direction, gauge and drain outlets, and UL Listing and FM Approval markings.

The Model CR Commercial Riser is available in four con-figurations (see Figures 1 and 2):

• Basic TrimCommercial riser manifold assembly includes a cU-Lus Listed pressure gauge, a ¼” three-way valve, a drain (ball) valve, and a dedicated waterflow detector containing two sets of SPDT (Form C) contacts, hav-ing an electrical rating of 10A @ 125/250 VAC/2.5 A @

24 VDC. See Table 3 for triggering flow rates.• Basic Trim with Pressure Relief Kit

Commercial riser manifold assembly includes a cU-Lus Listed pressure gauge, a ¼” three-way valve, a drain (ball) valve, and a dedicated waterflow detector containing two sets of SPDT (Form C) contacts, hav-ing an electrical rating of 10A @ 125/250 VAC/2.5 A @ 24 VDC. See Table 3 for triggering flow rates. The non-adj (2) ustable Pressure Relief Kit will maintain system pressures below 175 psi (12,1 bar).

• Basic Trim with Test and Drain Valves ValveCommercial riser manifold assembly includes a cU-Lus Listed pressure gauge, a ¼” three-way valve, a Test and Drain Valve, and a dedicated waterflow de-tector containing two sets of SPDT (Form C) contacts, having an electrical rating of 10A @ 125/250 VAC/2.5 A @ 24 VDC. See Table 3 for triggering flow rates. The available test orifice size inside the Test and Drain Valve are(Choose one):

• 3/8” (K-2.8) (1)

• 7/16” (K-4.2)

• 1/2” (K-5.6)

• 17/32” (K-8.0)

• 5/8” (K-11.2)(3)

• 3/4” (K-14.0)(3)

• 15/16” (K-16.8)(2) (3)

• 15/64” (K-22.4)(2) (3)

• 19/64” (K-25.2)(2) (3)

(1) Not available for 4”, 6” and 8” risers.(2) Not available for 11/2” to 3” risers.(3) Not available for 11/2” to 2” threaded & 2” grooved risers.

2.

Note:11/4” Grooved end Test and Drain valves are available in various orifice size as Made To Order (MTO).

Fig. 1

3.

Note:11/4” Grooved end Test and Drain valves are available in various orifice size as Made To Order (MTO).

Fig. 2

4.

Table 1 Dimensions & WeightsBasic Assembly Basic Assembly with Pressure Relief Kit

Manifold Pipe Size in (mm)

A in (mm)

B in (mm)

C in (mm)

D in (mm)

E in (mm)

Weight lbs (kg)

A in (mm)

B in (mm)

C in (mm)

D in (mm)

E in (mm)

Weight lbs (kg)

ThreadedEnds

(See Fig. 1)

11/2 (40) 11(279)

111/2 (292)

3(76)

73/4(197)

81/4(210)

8.3(3.8)

131/2(343)

123/4(324)

3(76)

73/4(197)

81/4(210)

10.4(4.7)

2 (50) 11(279)

121/4(311)

31/4(83)

8(203)

81/4(210)

9.1 (4.1)

131/2(343)

131/2(343)

31/4(83)

8(203)

81/4(210)

11.2(5.1)

Grooved Ends

(See Fig. 2)

2 (50) 123/4

(324)16

(406)51/4

(133)8

(203)13

(330)10.7(4.9)

163/4(425)

173/4(451)

51/4(133)

8(203)

13(330)

13.3 (6.0)

21/2

(65)123/4(324)

161/2(419)

51/2(140)

81/4(210)

13(330)

12.9(5.9)

163/4(425)

181/4(464)

51/2(140)

81/4(210)

13(330)

16.7(7.6)

3 (80) 123/4(324)

17(432)

53/4(146)

81/2(216)

13(330)

17.6(8.0)

163/4(425)

183/4(476)

53/4(146)

81/2(216)

13(330)

18.3(8.3)

4 (100) 121/2

(318)19

(483)61/4

(159)9

(229)13

(330)21.3(9.7)

163/4(425)

191/2(495)

7(168)

9(229)

13(330)

26.7 (12)

6 (150) 121/2

(318)20

(508)61/4

(159)10

(254)13

(330)26.3(12)

163/4(425)

201/2(521)

7(178)

10(254)

13(330)

31.8(14.4)

8 (200) 121/2

(318)22

(559)41/4

(184)11

(280)13

(330)31.0

(14.1)163/4(425)

221/2(572)

8(203)

11(280)

13(330)

36.5(16.6)

Table 2Dimensions & Weights

Basic Assembly with Test and Drain ValveBasic Assembly

with Test and Drain Valve & Pressure Relief KitManifold Pipe Size in (mm)

A in (mm)

B in (mm)

C in (mm)

D in (mm)

E in (mm)

Weight lbs (kg)

A in (mm)

B in (mm)

C in (mm)

D in (mm)

E in (mm)

Weight lbs (kg)

ThreadedEnds

(See Fig. 1)

11/2 (40) 11(279)

16(406)

3(76)

73/4

(197)81/4

(210)10.0(4.5)

15(381)

16(406)

3(76)

73/4

(197)81/4

(210)10.8(4.9)

2 (50) 11(279)

161/2(419)

31/4(83)

8(203)

81/4(210)

10.8(4.9)

15(381)

161/2(419)

31/4(83)

8(203)

81/4(210)

11.6(5.3)

GroovedEnds

(See Fig. 2)

2 (50) 123/4

(324)181/2(470)

51/4(133)

8(203)

13(330)

10.7(4.9)

151/2(394)

181/2(470)

51/4(133)

8(203)

13(330)

13.3(6.0)

21/2 (65) 123/4

(324)19

(475)51/2

(140)81/4

(210)13

(330)12.9(5.9)

151/2(394)

19(475)

51/2(140)

81/4(210)

13(330)

16.1(7.3)

3 (80) 123/4

(324)193/4

(502)53/4

(146)81/2

(216)13

(330)17.6(8.0)

151/2(394)

193/4

(502)53/4

(146)81/2

(216)13

(330)17.0(7.7)

4 (100) 14(356)

23(584)

63/4

(172)9

(229)13

(330)25.8

(11.6)181/2

(470)23

(584)63/4

(172)9

(229)13

(330)26

(11.8)

6 (150) 14(356)

251/2(648)

8(203)

10(254)

13(330)

30(13.6)

181/2

(470)251/2(648)

8(203)

10(254)

13(330)

31(14.1)

8 (200) 141/4

(362)27

(686)9

(229)11

(280)13

(330)35.3(16)

181/2

(470)27

(686)9

(229)11

(280)13

(330)36.3

(16.5)

5.

• Basic Trim with Test and Drain Valve & Pressure Relief KitCommercial riser manifold assembly includes a cU-Lus Listed pressure gauge, a ¼” three-way valve, a Test and Drain Valve, and a dedicated waterflow de-tector containing two sets of SPDT (Form C) contacts, having an electrical rating of 10A @ 125/250 VAC/2.5 A @ 24 VDC. See Table 3 for triggering flow rates. The non-adjustable Pressure Relief Kit will maintain system pressures below 175 psi (12,1 bar). The available test orifice size inside the Test and Drain Valve are(Choose one):

• 3/8” (K-2.8)(1)

• 7/16” (K-4.2)

• 1/2” (K-5.6)

• 17/32” (K-8.0)

• 5/8” (K-11.2)(3)

• 3/4” (K-14.0)(3)

• 15/16” (K-16.8)(2) (3)

• 15/64” (K-22.4)(2) (3)

• 19/64” (K-25.2)(2) (3)


Installation1. Attach the pressure gauge as shown in Figures 1-4.2. Install the manifold with the flow arrow pointing

towards the SYSTEM side using threaded fittings or grooved pipe couplings.

3. Connect the appropriately sized drain line.4. Ensure that the drain valve is in the CLOSED posi-

tion.5. Place the sprinkler system in service.6. Installation must comply with NFPA 13, Section

8.16.4.2

Caution:Automatic sprinkler systems having non-fire protection

connection (permitting continual water flow) require dielec-tric fittings, according to NFPA 13 sect. 4-6, when dissimilar metal piping materials are joined.

Note:Use a non-hardening pipe joint compound, or teflon tape.

Follow the manufacturer’s instructions when using grooved pipe couplings.

Listings and Approvals1. Listed by Underwriters’ Laboratories Inc. and ULC

Listed.2. Factory Mutual Approved.3. NYC MEA 258-93-E

Engineering Specifi cation [Model CR Commercial Riser Assembly] shall be [UL

Listed][ULC Listed] [Factory Mutual (FM) Approved] for hor-izontal or vertical installation as a one-piece, fabricated as-sembled unit. The [Model CR Commercial Riser Assembly] shall consist of a (choose one):

• 11/2” (40 mm) cast, non-welded stainless steel body with threaded end connections

• 2” (50 mm) cast, non-welded, stainless steel body with threaded end connections

• 2” (50 mm) cast, non-welded, ductile iron body with grooved end connections

• 21/2” (65 mm) cast, non-welded, ductile iron body with grooved end connections





having all brass and galvanized trim. The manifold pip-ing shall clearly identify the manifold’s pipe size, flow di-rection, UL Listing/ ULC Listing/ FM Approval, drain, and gauge outlets. A built-in drain port shall be available to permit hydrostatic testing without draining the system. This drain port shall be sized per the following:

• 1”(25mm) for 1½”(40mm) and 2”(50mm) sizes.• 11/4”(32 mm) for 2½”(65mm), and 3”(80mm) sizes.• 2”(50mm) for 4”(100mm), 6”(150mm) and 8”(200mm)

sizes.Take-out dimensions shall be the same for the 1½” (40mm)

and 2” (50mm) threaded sizes. End-to-end dimensions shall be the same for the 2” (50mm) through 3” (80mm) grooved sizes. Assembly shall have a working pressure rating of [250 psi (17,2 bar) (for 1½” (40mm) and 2” (50mm) threaded manifold assemblies)] [300 psi (20,7 bar) (for 2” through 3” grooved manifold assemblies)].

End-to-end dimensions shall be the same for the 4” (100mm) through 8” (200mm) grooved sizes. Assembly shall have a working pressure rating of [300 psi (20,7 bar) (for 4” (100mm) through 8” (200mm) grooved manifold as-semblies)].

Table 3

Manifold Sizes Triggering Flow Rate - GPM (LPM)

1½”(40mm), 2”(50mm),2½”(65mm) & 3”(80mm)

4 (15) to 10 (38)

4” (100mm), 6”(150mm),& 8”(200mm)

4 (15) to 10 (38)

Ordering Information:Model CR Commercial Riser Assembly Part Number Code Key

1.5NT1.5MT2NT2MT2G

2.5G3G4G6G8G

1.5NT = 11/2” (40 mm)NPT Threaded Ends Assembly

1.5MT = 11/2” (40 mm)Metric Threaded Ends Assembly

2NT = 2” (50 mm)NPT Threaded Ends Assembly

2MT = 2” (50 mm)Metric Threaded Ends Assembly

2G = 2” (50 mm)Grooved Ends Assembly

2.5G = 21/2” (65 mm)Grooved Ends Assembly



6G = 6” (150mm)Grooved Ends Assembly


BT28 (K-2.8)(1)

T42 (K-4.2)T56 (K-5.6)T80 (K-8.0)

T112 (K-11.2)(3)

T140 (K-14.0)(3)

T168 (K-16.8)(2) (3)

T224 (K-22.4)(2) (3)

T252 (K-25.2)(2) (3)

B = Basic Assembly

T28 = W / K-2.8 Test & Drain Valve




T112 = W / K-11.2 Test & Drain Valve(3)

T140 = W / K-14.0 Test & Drain Valve(3)

T168 = W / K-16.8 Test & Drain Valve(2) (3)

T224= W / K-22.4 Test & Drain Valve(2) (3)

T252 = W / K-25.2 Test & Drain Valve(2) (3)


For Grooved end Test and Drain valves(See note 3)

0123

0 = Assembly without Pressure Relief KitWater Detector - cULus & FM

1 = Assembly with Pressure Relief KitWater Detector - cULus & FM

2 = Assembly without Pressure Relief KitWater Detector - ULC

3 = Assembly with Pressure Relief KitWater Detector - ULC

Example #1: 1.5NT – B – 1(1½” (40mm) Model CR Commercial Riser Assembly with NPT female inlet and outlet threads, basic trim with installed Pressure Relief Kit).Example #2: 3G – T56 – 0(3”(80mm) Model CR Commercial Riser Assembly with grooved ends, basic trim with Test and Drain Valve having a 5.6 K factor, without a Pressure Relief Kit)Example #3: 6G – T80 – 0(6”(150mm) Model CR Commercial Riser Assembly with grooved ends, basic trim with Test and Drain Valve having a 8.0 K factor, without a Pressure Relief Kit)Notes: 1. All Model CR Commercial Riser Assemblies come with a 300 psi (20,7 bar) UL Listed and FM Approved pressure

gauge for 175 psi (12,1 bar) applications. If the Model CR Commercial Riser Assembly is to be installed in a 300 psi (20,7 bar) application, please purchase a 600 psi (41,4 bar) (P/N 98248005) pressure gauge. This gauge may or may not be UL Listed and/or FM Approved at the time of purchase.

2. If required, Pressure Relief Kits may also be installed in the field. Please contact Reliable’s Customer Service Department for details.

3. 11/4” and 2” Grooved end Test and Drain valves are available in various orifice size K factor as MTO. Please contact Reliable Service Department for details.

Reliable Automatic Sprinkler Co., Inc.(800) 431-1588 Sales Offices(800) 848-6051 Sales Fax(914) 829-2042 Corporate Officeswww.reliablesprinkler.com Internet Address


Paper


E.G. Printed in U.S.A. 05/15 P/N 9999970349


SECTION 5

HANGERS

ERICO 115 STANDARD DUTY LOOP HANGER [OR EQUAL]

PiPe

Ha

ng

ers

115 Standard Duty Loop Hanger

15www.erico.com

The 115 Standard Duty Loop Hanger, part of the CADDY® line of fasteners and supports from ERICO, is ideal for suspending stationary, non-insulated pipe lines, including CPVC pipes, in fire sprinkler systems. A knurled insert nut helps simplify vertical adjustments and flared edges on the base (1/2” to 2” sizes) help protect pipes from coming into contact with any sharp edges of the hanger.

Features • Flared edges help prevent any sharp surfaces from coming into contact with the pipe (1/2” to 2” sizes) • Retained insert nut helps ensure the loop hanger and insert nut stay together • Recommended for the suspension of stationary non-insulated pipe lines • Manufactured to use the minimum rod size permitted by NFPA® for fire sprinkler piping • Conforms with Federal Specification WW-H-171 (Type 10), Manufacturers Standardization Society (MSS) SP-58

and SP-69 (Type 10)

Specifications Material: Steel Finish: Pre-galvanized

Part Number Pipe Size Outer DiameterOD

Rod SizeRS

A B C Static LoadF

1150050EG 1/2” 0.840” 3/8” 2 13/16” 1 1/8” 1” 300 lb

1150075EG 3/4” 1.050” 3/8” 3” 1 3/16” 15/16” 300 lb

1150100EG 1” 1.315” 3/8” 3 1/4” 1 3/8” 15/16” 300 lb

1150125EG 1 1/4” 1.660” 3/8” 3 9/16” 1 1/2” 15/16” 300 lb

1150150EG 1 1/2” 1.900” 3/8” 3 13/16” 1 5/8” 15/16” 300 lb

1150200EG 2” 2 3/8” 3/8” 4 1/4” 1 7/8” 15/16” 300 lb

1150250EG 2 1/2” 2 7/8” 3/8” 5 9/16” 2 13/16” 1 9/16” 525 lb

1150300EG 3” 3 1/2” 3/8” 6 9/16” 3 1/2” 1 15/16” 525 lb

1150350EG 3 1/2” 4” 3/8” 7 1/16” 3 3/4” 1 15/16” 585 lb

1150400EG 4” 4 1/2” 3/8” 7 9/16” 4” 1 15/16” 650 lb

1150500EG 5” 5 9/16” 1/2” 9 13/16” 4 3/4” 2 1/4” 1,000 lb

1150600EG 6” 6 5/8” 1/2” 11 5/16” 6 5/16” 3 5/16” 1,000 lb

1150800EG 8” 8 5/8” 1/2” 12 7/8” 6 7/8” 2 7/8” 1,000 lb

SECTION 6

ELECTRICAL DEVICES

BRECCO 10”, 120 VOLT ELECTRIC BELL [OR EQUAL]

27www.breccocorp.com E-mail: [email protected]

Electrical

Bells - Electric

Back Boxes

Features four wire, 120V and 24V Red enamel heavy steel gong.Indoor and outdoor installation.

UL Approved.

Weatherproof.For use in attaching electric bells to walls.

Part No. Description BoxQty.

BoxWeight

CaseQty.

CaseWeight

ELAB12006 6” 120V 1 3.3 Lbs. 20 68 Lbs.

ELAB12008 8” 120V 1 3.4 Lbs. 10 37 Lbs.

ELAB12010 10” 120V 1 4.4 Lbs. 10 47 Lbs.

ELAB12006 6” 24V 1 3.3 Lbs. 20 68 Lbs.

ELAB12010 10” 24V 1 4.4 Lbs. 10 47 Lbs.

Part No. Description CaseQty.

CaseWeight

ELBBB BELL BACK BOX W/ GASKET AND SCREWS 50 33 Lbs.

SECTION 7

MISCELLANEOUS

BRECCO 12-COUNT SPRINKLER CABINET [OR EQUAL]

BRECCO WATER PRESSURE GAUGE KITS [OR EQUAL]

BRECCO GLOBE VALVES [OR EQUAL]

BRECCO SWING CHECK VALVES [OR EQUAL]

BRECCO ANGLE VALVES [OR EQUAL]

BRECCO FLOOR/CEILING PLATES [OR EQUAL]


Spare Head Cabinets

Sight Glass

All welded construction with full length hinge and 1/2” holes with 3/4” knock outs or sizes as noted.

.

Part No. Description CaseQty.

ACHB03 3 HEAD - 1/2” x 3/4” HOLES 50ACHB06 6 HEAD - 1/2” x 3/4” HOLES 25ACHB12 12 HEAD - 1/2” x 3/4” HOLES 20ACHB6ESFR100 6 HEAD - ESFR 3/4” x 1” HOLES 10


CaseQty.

ACSGFF100 1” FULL FLOW 5 40ACSG100050 1” W/ 1/2” ORIFICE 5 40ACSG1001732 1” W/ 17/32” ORIFICE 4 AR*ACSGFF125 1-1/4” FULL FLOW 4 24ACSGCUSTOM 1” OTHER ORIFICES 5 40

*As Requested.

Accessories

26Call Toll Free: 1-800-543-4194 Fax: 1-877-474-9248

Gauges

Gauges

For use with wet or dry systems.Gauges have a bronze burbon tube movement in a stainless steel case.*

3-1/2” Diameter• UL and FM approved.*• Custom gauges can be made.•

*Unless otherwise noted.

3-Way ValveIncluded inAccessory Pack!


CrateQty.

GAAWSS350 AIR/WATER 0-300 PSI W/ STAINLESS STEEL CASE 60 480

GAASS250 AIR W/ RETARD 250 PSI 3-1/2” DIAMETER, W/ STAINLESS STEEL CASE 60 480

GAWP200 2” RESIDENTIAL GAUGE 300 PSI W/ BLACK STEEL CASE (NOT UL OR FM APPROVED) 150 1200

GAUGE KITS - AIR OR AIR/WATER

GAKITAWSS350AIR/WATER GAUGE 0-300 PSI W/ STAINLESS STEEL CASE, 1/4” x 4” NIPPLE, 1/4” 3 WAY VALVE, 1/4” PLUG, 1/2” x 1/4” HEXHEAD REDUCING BUSHING

10 NA

GAKITAOSS250AIR GAUGE 0-250 PSI W/ STAINLESS STEEL CASE, 1/4” x 4” NIPPLE, 1/4” 3 WAY VALVE, 1/4” PLUG, 1/2” x 1/4” HEXHEAD REDUCING BUSHING

10 NA

Gauges can be custom branded with your name and logo.

Please call for more information.


Valves

Globe Valves

Swing Check Valve - Rubber Seat


CaseQty.

VAGV025 1/4” 10 100VAGV050 1/2” 10 100VAGV075 3/4” 10 60VAGV100 1” 5 40VAGV125 1-1/4” 5 30VAGV150 1-1/2” 4 24VAGV200 2” 2 16


CaseQty.

VACVSW050 1/2” 10 120VACVSW075 3/4” 10 80VACVSW100 1” 5 60VACVSW125 1-1/4” 5 40VACVSW150 1-1/2” 5 30VACVSW200 2” 4 24

Bronze Globe Valve w/ Rubber disc. Rated @ 200 PSI.•

•

Typical use is in trim or drain applications.• Hand wheel - JIS FC 20 painted Red.• For use as trim or drain valves.•

Brass Swing Check Valve: 150 WSP.Rubber seat w/ nuts and washer.• 200 PSI.•

6Call Toll Free: 1-800-543-4194 Fax: 1-877-474-9248

Valves

Angle Valves

Ball Drip Valves


CaseQty.

VAAV050 1/2” 10 100VAAV075 3/4” 10 60VAAV100 1” 5 30VAAV125 1-1/4” 5 20VAAV150 1-1/2” 4 16VAAV200 2” 2 10


CaseQty.

VABD50 1/2” 14 112VABD75 3/4” 10 100

Brass Angle Valve w/ Rubber disc rated @ 200 PSI. For use as trim or drain valves.•

Brass body w/ brass ball.

department connection if used with approved check valves.


Escutcheons

Floor & Ceiling Plates (Plastic)

ease of installation.

Available in White or Chrome.


ESPLFCPC0050 1/2” C.P. 12ESPLFCPC0075 3/4” C.P. 12ESPLFCPC0100 1” C.P. 12ESPLFCPC0125 1-1/4” C.P. 12ESPLFCPC0150 1-1/2” C.P. 12ESPLFCPC0200 2” C.P. 12ESPLFCPC0250 2-1/2” C.P. 12ESPLFCPC0300 3” C.P. 12ESPLFCPC0400 4” C.P. 12ESPLFCPC0500 5” C.P. 6ESPLFCPC0600 6” C.P. 6ESPLFCPC0800 8” C.P. 6ESPLFCPW0050 1/2” WHITE 12ESPLFCPW0075 3/4” WHITE 12ESPLFCPW0100 1” WHITE 12ESPLFCPW0125 1-1/4” WHITE 12ESPLFCPW0150 1-1/2” WHITE 12ESPLFCPW0200 2” WHITE 12ESPLFCPW0250 2-1/2” WHITE 12ESPLFCPW0300 3” WHITE 12ESPLFCPW0400 4” WHITE 12ESPLFCPW0500 5” WHITE 6ESPLFCPW0600 6” WHITE 6ESPLFCPW0800 8” WHITE 6

Documents

Submittal Transmittal Banner Tatum/Grnway - Const Project ...€¦ · Fig. 1 and 3, are a friction fit assembly allowing for 3/4-inch (19mm) and 1/2-inch (12.7mm) of adjustment, respectively