INSTALLATION OF STI-7600 MEGA STOPPERAll specifications and
information shown were current as of publication and are subject to
change without notice.
7600IS DEC2010
Safety Technology International, Inc.2306 Airport Road
Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax:
248-673-1246Toll Free: 800-888-4784 E-mail: [email protected]:
www.sti-usa.com
Safety Technology International (Europe) Ltd.Unit 49G Pipers
Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU
England Tel: 44 (0) 1527 520 999 Fax: 44 (0) 1527 501 999 E-mail:
[email protected] Web: www.sti-europe.com
VIEW AINSTALLATION INSTRUCTIONS1. Center cover over device to be
protected.2. Place a mark near the location of the cam latch.3.
Install cam latch and latch spacer if gasket is used.4. Turn key or
thumb lock to locked position (cam is facing downward,
see view A).5. Place cover over device making sure cam is fully
engaged under
cam latch (see view A).6. Force cover against wall and mark
mounting holes.7. Remove cover and drill 3/16 in.(4.7mm) diameter
holes.8. Install gasket and cover assembly with screws provided.
The use of
provided anchors is optional.
PRODUCT DIMENSIONS
CLEANING INSTRUCTIONSRinse with water to remove abrasive dust
and dirt. Wash with soap or mild detergent using a soft cloth. DO
NOT SCRUB OR USE BRUSHES OR ABRASIVES. Rinse once more, then dry
with a soft cloth or chamois. To remove grease or wet paint, rub
gently with a cloth wetted thoroughly with naphtha. Then wash and
rinse. DO NOT USE RAZOR BLADES OR GASOLINE.
Electronic warranty form at www.sti-usa.com/wc14
GASKET
19018 ANCHOR
CAM LATCH
19039 SCREW
CUTAWAY SECTION OF COVER
07503 THUMB LOCK (SHOWN)18050 KEY LOCK
(2) KEYS PROVIDED
A
LATCH SPACER (OPTIONAL)DISCARD IF GASKETIS NOT USED
19033 ANCHOR(3) PROVIDED WITH STI-7500H(2) PROVIDED WITH
STI-7500V
R.H. HINGE PINL.H. HINGE PINPART OF STI-7500H
(HORIZONTAL)STI-7500V (VERTICAL)
19013 SCREW #10 x 1 1/2 in.(3) PROVIDED WITH STI-7500H(2)
PROVIDED WITH STI-7500V
STI-7500H COVER ASSEMBLY WITH KEY LOCKSTI-7501H COVER ASSEMBLY
WITH THUMB LOCKSTI-7500V COVER ASSEMBLY WITH KEY LOCKSTI-7501V
COVER ASSEMBLY WITH THUMB LOCK
HORIZONTAL
VERTICAL
750099 GASKET(ADHESIVE SIDE TOWARD MOUNTING SURFACE)
NOTE: IF GASKET IS TO BE USED
HORIZONTAL MODELS - REMOVE HINGEMOUNTING TAB AT PERFORATED
LINE
ON VERTICAL SURFACE AS SHOWN.
VERTICAL MODELS - REMOVE HINGEMOUNTING TAB AT PERFORATED
LINE
ON HORIZONTAL SURFACE.
REMOVE BACKING PAPERPRIOR TO INSTALLATION
REMOVE FORVERTICAL COVERS
REMOVE FORHORIZONTAL COVERS
PERFORATED LINE
.75 in.(19mm)
3.50R in.(89mm)
6.50 in.(165mm)
1.00 in.(25mm)
3.50R in. (89mm)
.75 in.(19mm)
8.50 in.(216mm)
SIDE VIEW
.75 in.(19mm)
3.50 in.(89mm)
6.50R in.(165mm)
1.00 in.(25mm)
3.50R in. (89mm).75 in.(19mm)
8.50 in.(216mm)
SIDE VIEW
TOP VIEW
TOP VIEW
A
760099 GASKET (ADHESIVE BACKED)
19033 ANCHOR(4) PROVIDED
RIGHT HINGE PIN
19013 SCREW#10 x 1 1/2 in.(4) PROVIDED
STI-7600 COVER ASSEMBLY WITH KEY LOCKSTI-7601 COVER ASSEMBLY
WITH THUMB LOCK
LEFT HINGE PIN
TOP VIEW
END VIEW
6 in.(152mm)
13 in.(330mm)
1.5 in.(38mm)
REMOVE BACKING PAPER
FRONT VIEW
TOP VIEW
13 in.(330mm)
6 in.(152mm)
1.5 in.(38mm)
GASKET (ADHESIVE BACKED)
(2) HINGE PINS(PART OF ASM.)
STI-7600 COVER ASM. W/KEY LOCKSTI-7601 COVER ASM. W/THUMB
LOCK
A
FRONT VIEW
SIDE VIEW
13 in.(330mm)
6 in.(152mm)
1.5 in.(38mm)
GASKET (ADHESIVE BACKED) (2) HINGE PINS(PART OF ASM.)
STI-7600 COVER ASM. W/KEY LOCKSTI-7601 COVER ASM. W/THUMB
LOCK
A
GASKET
A
4.125 in.(105mm)
4.125 in.(105mm)
4.125 in.(105mm)
6.235 in.(158mm)
7.259 in.(184mm)
BB
A
1.334 in.(34mm)
1.644 in.(42mm)
1.825 in.(46mm)
5.14 in.(131mm)
5.882 in.(150mm)
SECTION A-A
SECTION B-B
12.867 in.(327mm) 12.96 in.
(329mm)13.220 in.(336mm)
A
