TYPICAL LIFELINE INSTALLATION USING STANDARD HANGERS STANDARD LIFELINE INSTALLATION INSTRUCTIONS 1. INSTALL FIRST HANGER. ANCHOR THE OUT-BY END OF LIFELINE WITH THE SUPPLIED TENSIONING CLAMP. SEE DIAGRAM. 2. BEGIN UNROLLING LIFELINE, CLIPPING INTO SUPPLIED HANGERS EVERY 25 TO 30 FEET. (EVERY 7TH ROW OF BOLTS). 3. TENSION THE MIDWAY POINT (APPROXIMATELY 500’) IN THE IN-BY DIRECTION USING ONE OF THE SUPPLIED TENSIONING CLAMPS. THEN ANCHOR THE MIDWAY POINT IN THE OUT-BY DIRECTION USING A SUPPLIED TENSIONING CLAMP AS SHOWN. SEE DIAGRAM. 4. CONTINUE INSTALLING LIFELINE UNTIL THE IN-BY END IS REACHED. 5. TENSION THE IN-BY END OF LIFELINE USING ONE OF THE SUPPLIED TENSIONING CLAMPS. SEE DIAGRAM. 6. CONNECT THE NEXT ROLL BY SCREWING THE THREADED MALE AND FEMALE CONNECTOR ENDS TOGETHER. 7. REPEAT FOR EACH CONSECUTIVE ROLL. 304-855-7080 [email protected] MIDWAY RECOMMENDED HANGER SPACING = 25’-30’ THREADED FEMALE CONNECTOR 3 MANDOOR INDICATORS IN EACH KIT -TWO PIECE POLYCARBONATE CONSTRUCTION -SNAP ON, REUSABLE DESIGN -NO TOOLS REQUIRED 4 TENSIONING CLAMPS IN EACH KIT ANCHOR MIDWAY POINT WITH SUPPLIED TENSIONING CLAMP SNAP HOOK W/ RUBBER COATING TENSION MIDWAY POINT WITH SUPPLIED TENSIONING CLAMP ROOF PLATE OPEN “S” HOOK CLOSED SNAP HOOK THREADED MALE CONNECTOR NOTES: *LIFELINES MUST BE INSTALLED IN A MANNER FOR MINERS TO EFFECTIVELY USE DURING ESCAPE. *ESCAPEWAYS MUST BE MAINTAINED TO A WIDTH OF 6 FEET, EXCEPT WHERE SUPPLEMENTAL ROOF SUPPORT IS INSTALLED. THEN THE MINIMUM WIDTH IS 4 FEET. RED “X” ILLUMINATES LIFELINE IN THE OPPOSITE DIRECTION AND ELIMINATES CONFUSION, REGARDLESS OF COLOR. X TENSION IN-BY END OF CABLE WITH SUPPLIED TENSIONING CLAMP ANCHOR OUT-BY END OF CABLE WITH SUPPLIED TENSIONING CLAMP OUT-BY END IN-BY END

STANDARD LIFELINE INSTALLATION INSTRUCTIONS · typical lifeline installation using standard hangers standard lifeline installation instructions 1. install first hanger. anchor the

Download PDF Report

Upload
phamthu
View
216
Download
0

Embed Size (px)

Citation preview

TYPICAL LIFELINE INSTALLATION USING STANDARD HANGERS

STANDARD LIFELINE INSTALLATION INSTRUCTIONS1. INSTALL FIRST HANGER. ANCHOR THE OUT-BY END OF LIFELINE WITH THE SUPPLIED TENSIONING CLAMP. SEE DIAGRAM.2. BEGIN UNROLLING LIFELINE, CLIPPING INTO SUPPLIED HANGERS EVERY 25 TO 30 FEET. (EVERY 7TH ROW OF BOLTS).3. TENSION THE MIDWAY POINT (APPROXIMATELY 500’) IN THE IN-BY DIRECTION USING ONE OF THE SUPPLIED TENSIONING CLAMPS. THEN ANCHOR THE MIDWAY POINT IN THE OUT-BY DIRECTION USING A SUPPLIED TENSIONING CLAMP AS SHOWN. SEE DIAGRAM.4. CONTINUE INSTALLING LIFELINE UNTIL THE IN-BY END IS REACHED.5. TENSION THE IN-BY END OF LIFELINE USING ONE OF THE SUPPLIED TENSIONING CLAMPS. SEE DIAGRAM.6. CONNECT THE NEXT ROLL BY SCREWING THE THREADED MALE AND FEMALE CONNECTOR ENDS TOGETHER.7. REPEAT FOR EACH CONSECUTIVE ROLL.

[email protected]

MIDWAY

RECOMMENDED HANGERSPACING = 25’-30’

THREADEDFEMALE

CONNECTOR

3 MANDOOR INDICATORS IN EACH KIT-TWO PIECE POLYCARBONATE CONSTRUCTION-SNAP ON, REUSABLE DESIGN-NO TOOLS REQUIRED

4 TENSIONING CLAMPS IN EACH KIT

ANCHOR MIDWAY POINTWITH SUPPLIED

TENSIONING CLAMP

SNAP HOOK W/ RUBBER COATING

TENSION MIDWAY POINTWITH SUPPLIED

TENSIONING CLAMP