Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
INSTALLATION INSTRUCTIONS CRS-INST© Panduit Corp. 2014
www.panduit.com
For instructions in Local Languagesand Technical Support:
www.panduit.com/resources/install_maintain.asp
E-mail:[email protected]
Phone:866-405-6654
Rev. 04Page 1 of 1
MALE DOVETAIL
FEMALE DOVETAIL SLOT
CABLE TIE SLOTCABLE TIE SLOT
LATCH
FEMALE DOVETAIL SLOT
APPLICATIONSURFACE
MALE DOVETAIL
LATCH RETAINING FACE
CABLE RETAINING POST
Figure 1
Figure 4 Figure 5 Figure 6 Figure 7
Figure 2 Figure 3
1) Secure bottom level of Stackable Cable Rack Spacer to the application surface, i.e. ladder rackrung with two standard cross-section Panduit Pan-Ty Cable Ties (Figures 1, 2, and 3).
2) Install cable or cable bundles into each of the cable retaining areas.
3) Secure cable to the cable retaining post with Panduit Pan-Ty Cable Ties, Belt-Ty In-LineCable Ties, or Tak-Ty Hook and Loop Cable Ties up to 0.33" in width.
4) Installation of the next level of Stackable Cable Rack Spacers is accomplished by sliding themale dovetail into the female dovetail slot (Figures 4, 5, and 6). The latch(s) will lock the partsinto position. To unlock these parts, use a screwdriver or a small tool to release latch(s) andslide in opposite direction.
5) Repeat steps 2, 3, and 4 until a maximum stack height is achieved. Panduit recommends amaximum stack height of five for the CRS6-X and CRS1-X. A maximum stack height of four isrecommended for the CRS1-125-X and CRS4-125-X. Stackable Cable Rack Spacers arereversible to allow cable retaining posts to be alternated (Figure 7).
CABLE TIESLOT(S)
FEMALE DOVETAIL(S) &
LATCH(S)APPLICATION SURFACE LADDER RACK RUNG
MALE DOVETAILMALE DOVETAIL
CABLE RETAINING POST
MALE DOVETAIL
FEMALE DOVETAIL SLOT CABLE TIE SLOT
CABLE TIE SLOT LATCH
FEMALE DOVETAIL SLOT
APPLICATIONSURFACE
MALE DOVETAIL
LATCH RETAINING FACE
CABLE RETAINING POST
DIRECTION OF MOTION FOR OPPOSITE ORIENTATION OF CABLE RETAINING POSTS
LEVEL 1
LEVEL 2
DIRECTION OF MOTION FOR SAME ORIENTATION OF CABLE RETAINING POSTS
BASE LEVELCABLE RACK SPACER
APPLICATION SURFACE- LADDER RACK RUNG
CABLE RETAINING POST
Stackable Cable Rack SpacersPart Numbers: CRS1-X, CRS1-125-X, CRS4-125-X, CRS6-X
INSTALLATION INSTRUCTIONS CRS-INST© Panduit Corp. 2014
www.panduit.com
For instructions in Local Languagesand Technical Support:
www.panduit.com/resources/install_maintain.asp
E-mail:[email protected]
Phone:866-405-6654
Rev. 04Page 1 of 1
MALE DOVETAIL
FEMALE DOVETAIL SLOT
CABLE TIE SLOTCABLE TIE SLOT
LATCH
FEMALE DOVETAIL SLOT
APPLICATIONSURFACE
MALE DOVETAIL
LATCH RETAINING FACE
CABLE RETAINING POST
Figure 1
Figure 4 Figure 5 Figure 6 Figure 7
Figure 2 Figure 3
1) Secure bottom level of Stackable Cable Rack Spacer to the application surface, i.e. ladder rackrung with two standard cross-section Panduit Pan-Ty Cable Ties (Figures 1, 2, and 3).
2) Install cable or cable bundles into each of the cable retaining areas.
3) Secure cable to the cable retaining post with Panduit Pan-Ty Cable Ties, Belt-Ty In-LineCable Ties, or Tak-Ty Hook and Loop Cable Ties up to 0.33" in width.
4) Installation of the next level of Stackable Cable Rack Spacers is accomplished by sliding themale dovetail into the female dovetail slot (Figures 4, 5, and 6). The latch(s) will lock the partsinto position. To unlock these parts, use a screwdriver or a small tool to release latch(s) andslide in opposite direction.
5) Repeat steps 2, 3, and 4 until a maximum stack height is achieved. Panduit recommends amaximum stack height of five for the CRS6-X and CRS1-X. A maximum stack height of four isrecommended for the CRS1-125-X and CRS4-125-X. Stackable Cable Rack Spacers arereversible to allow cable retaining posts to be alternated (Figure 7).
CABLE TIESLOT(S)
FEMALE DOVETAIL(S) &
LATCH(S)APPLICATION SURFACE LADDER RACK RUNG
MALE DOVETAILMALE DOVETAIL
CABLE RETAINING POST
MALE DOVETAIL
FEMALE DOVETAIL SLOT CABLE TIE SLOT
CABLE TIE SLOT LATCH
FEMALE DOVETAIL SLOT
APPLICATIONSURFACE
MALE DOVETAIL
LATCH RETAINING FACE
CABLE RETAINING POST
DIRECTION OF MOTION FOR OPPOSITE ORIENTATION OF CABLE RETAINING POSTS
LEVEL 1
LEVEL 2
DIRECTION OF MOTION FOR SAME ORIENTATION OF CABLE RETAINING POSTS
BASE LEVELCABLE RACK SPACER
APPLICATION SURFACE- LADDER RACK RUNG
CABLE RETAINING POST
Stackable Cable Rack SpacersPart Numbers: CRS1-X, CRS1-125-X, CRS4-125-X, CRS6-X