Upload
josip-hrdan
View
218
Download
0
Embed Size (px)
Citation preview
8/11/2019 ST71T_ENG
1/74
DIGITAL CAMERA CONTENTS
SAMSUNG ES95/ES96/ES99/ST71T
DIGITAL CAMERA
SERVICE
Manual
1. Repair information
2. Product specifications
3. Disassembly and reassembly
4. Troubleshooting
5. PCB diagrams
6. Block diagram
7. Firmware update
8. Adjustment
9. Exploded view and parts list
8/11/2019 ST71T_ENG
2/74
Contents
1. Repair information
1-1 Customer satisfaction statement ............................................. 1-1
1-2 Warranty and repair service information ..................................1-1
1-3 Precaution for disassembly and reassembly ............................ 1-4
2. Product specifications
2-1 Specifications ................... .................... ................... .............. 2-1
2-2 Product comparison ............................................................... 2-2
2-3 Accessories information ......................................................... 2-3
2-4 About the memory card .......................................................... 2-5
2-5 About the battery ................. .................... .................... .......... 2-6
3. Disassembly and reassembly
3-1 Disassembly of main unit ....................................................... 3-1
3-2 Disassembly of barrel .......................................................... 3-11
3-3 Reassembly of barrel ........................................................... 3-16
3-3-1 How to use the lubricant for anti-friction to the ASSY BARREL assembly ....................3-16
3-3-2 Reassembly of barrel ........................................................ 3-19
4. Troubleshooting
4-1 Regarding to memory card recognition ................................... 4-1
4-2 Regarding to MAIN PCB connection ...................................... 4-2
4-3 Regarding to TOP switch (Power/Shutter/Zoom) ...................... 4-2
4-4 Regarding to flash ................................................................. 4-3
4-5 Regarding to image display .................................................... 4-4
4-6 Regarding to voice playback and recording ............................. 4-4
5. PCB diagrams
5-1 MAIN PCB .............................................................................5-1
5-2 TOP PCB ...............................................................................5-2
6. Block diagram
8/11/2019 ST71T_ENG
3/74
Contents
7. Firmware update
7-1 Product reset .......................................................................... 7-1
7-2 Version check .......................................................................... 7-3
7-3 Firmwawre update ................................................................... 7-4
7-4 Main PCB recovery .................................................................. 7-6
8. Adjustment
8-1 Basic guide for adjustment ....................................................... 8-1
8-2 LENS SHADING ADJ (Color Shading) ...................................... 8-3
8-3 SHUTTER CLOSE TIME ADJ ................................................... 8-4
8-4 FLASH ADJ ............................................................................. 8-5
8-5 PUNT ADJ (AF) ......... .................... ................... .................... .. 8-6
8-6 CCD DEFECT PIXEL ADJ (DPC) ................... ................... ........ 8-8
8-7 BACKLASH ADJ ...................................................................... 8-9
8-8 VERTICAL LINE ADJ ............................................................. 8-10
8-9 SERIAL NUMBER WRITING ADJ .................... .................... ...8-11
9. Exploded view and parts list
9-1 ASSY BODY .................. .................... ................... ................... 9-1
9-2 ASSY MAIN ................... .................... ................... ................... 9-2
9-3 ASSY CHAMBER .................. ................... .................... ............ 9-3
9-4 ASSY COVER FRONT .................... .................... ................... .. 9-4
9-5 ASSY COVER BACK .................... ................... .................... ..... 9-5
9-6 ASSY TOP PCB .................... ................... .................... ............ 9-6
9-7 ASSY STROBO .................... ................... .................... ............ 9-7
9-8 ASSY BARREL ................. .................... .................... ............... 9-8
8/11/2019 ST71T_ENG
4/74
Precautions
Copyright 1995-2013 SAMSUNG. All rights reserved. 1-1
1. Repair information
1-1 Customer satisfaction statement
1-2 Warranty and repair service information
Combining perfect technical solutions with a customer-oriented approach is our top priority.
We treat our customers we serve with kindness, loyalty, respect and dignity.
We are committed to earn customers trust continuously through excellence in repair solutions.
We keep our promises and commitments to our customers.
Committed to quick and easy resolution of all support issues, we deliver industry-leading
response times.
[Guide]
We listen carefully to our customers' requirements and always nd an optimum solution for their needs.
We are committed to your satisfaction and have procedures in place to provide you with a fair, timely and effective means to resolve problems. It
combines industry leading preventive assistance with responsive support that helps us address problems quickly and effectively.
We will continuously maintain and improve our services to satisfy the needs of our customers.
We hold ourselves to the highest standards of customer satisfaction and service.
(1) General terms and conditions
It is guaranteed to be free of charge from defects in material and workmanship under normal use for a period
of one year from date of purchase.
Digital Camera and lens come with a one year limited warranty from the date of purchase.
* The duration of the warranty depends on the laws in the country in which it was purchased.
The following information will be required to process warranty requests:
a. We imply warranties to one year from the original date of purchase. In the event that the purchaser is
unable to provide a warranty card or proof of purchase, the warranty period will be determined by the
date of manufacture. The warranty period shall be decreased to three months from the original product
manufactured date.
b. The coverage under this warranty begins on the date of your purchase of the product. In the event
that a warranty card or proof of purchase is not available, a purchase receipt, preferably the purchase
invoice, to conrm the date of purchase is required for warranty service.
c. In the event that a valid date of purchase is not available, the warranty period will be determined by
the date of manufacture. The warranty period shall be decreased to three months from the original
product manufactured date.
8/11/2019 ST71T_ENG
5/74
Precautions
1-2 Copyright 1995-2013 SAMSUNG. All rights reserved.
(2) Limited Warranty
It reserves the right to retain any parts or components replaced at its discretion in the event of a defect no-
ticed in the product. The period with respect to retaining components may vary respectively depending on its
components. We are not liable to repair or replace its faulty product after the Warranty Period has expired.
* We warrant its retaining camera and lenses for ve years and three years for the accessories.
a. If a warranty claim is led after the product has been discontinued, we reserves the right to honor the
components warranty. Warranty period may vary depending on the type of components.
b. In the event that no identical warranty information is available for service repair, company has the right to provide warranty.
The warranty does not affect the consumers' rights against the company related to its information.
For the length of the period indicated on the chart below, it starts with the date of original purchase.
Part Name Warranty Period
Battery Charger
Six monthsAC Adaptor
Battery
Remote Control
CD SoftwareThree months
Earphone
Pouch for cameraNot applicable
Cable
(3) Warranty Period for components
Our liability under this warranty shall be limited to the following:
a. In the event of a same malfunction problem within two months after repair service by Samsung authorized technician,
we will repair or replace free of charge the component of the product which is found to be defective.
b. In the event of the component that you have paid the replacement cost is returned under normal use within one year at our premises,
such components will be replaced free of charge component of the product which is found to be defective.
8/11/2019 ST71T_ENG
6/74
Precautions
Copyright 1995-2013 SAMSUNG. All rights reserved. 1-3
Types of consumer damages Compensation
Failing to perform or
failing to function properly
under normal use
Required for essential repair within 10 days
after the purchase
Replace the prod-
uct or refund-
Required for essential repair within one
month after the purchase
Replace the
product or repair
at free of charge
Repair charges
Applicable
to repair
Problem occurred twice
due to same malfunctionFree of charge
Problem occurred three
times due to samemalfunction
Replace the prod-
uct or refund
Repair chargesProblem occurred four
times due to some other
malfunction
Not applicable
to repair
Within the period with
respect to retaining
components
Replace the product at the cost of the
depreciated value or refund its price
added 10% of depreciation
Failing to perform or
failing to function properly
as a result of willful intentand negligence of
customer
Applicable repair Repair charges
Not applicable to repair(Except for defects or malfunction as a result
of re or ood or other natural disasters
Replacementcharge
Repair charge and replace the prod-uct at the cost of the depreciated value
(4) Repair Claims
1) Repair free of charge
Essentially, the following causes of damage are covered:
a. Failing to function properly under normal use during the limited warranty period.
b. Repair Services free of charge is granted for the performance of a specic contract.
2) Repair charges This warranty does not cover damage caused by:
a. Defect occurring after the expiration of the Warranty Period.
b. Damage due to negligence, immersion in water, impact, loss and tampering.
c. Repair or alteration performed by any party other than Samsung authorized technicians.
d. Misuse or other improper use of the power button.
e. Exhausted parts such as batteries, lamps and lters, etc.
f. Defect that occurs due to sand, dirt liquid, etc. entering the inside of the product casing.
g. Consumable parts which have ceased working through normal use such as as earphone, battery discharger and various accessories.
h. Products purchased second hand or any damage that occurs due to a second hand or repair performed
by anyone other than Samsung or a Samsung authorized service station.
i. Fire, earthquake, ood or other natural disasters.
The warranty cover period for components is listed below as per table 1-2.
8/11/2019 ST71T_ENG
7/74
Precautions
1-4 Copyright 1995-2013 SAMSUNG. All rights reserved.
1-3 Precaution for disassembly and reassembly
Component Precautions
FPCBFPCB is brittle material. It can be easily damaged thus it should be handled with care.
It is recommended to use wooden or plastic tweezers for manual placement.
CCD (CMOS)
IR CUT Filter
LCD, LENS
Be careful not to stained your nger. It is recommended to use wooden or plastic tweezers
for manual placement. Stain is often caused by the Alcohol used in these components.
Find a clean, well-ventilated place to do your work.
PCB Use an anti-static mat as well as an anti-static wrist strap to avoid ESD damage to PCB.
CONNECTORThe use wooden or plastic tweezers is recommended for manual placement.
Metal tip tweezer might make marks or damage.
BARREL Always follow proper direction while assembling the components of the barrel.
1. Use the anti-static handing procedures included with the anti-static mat to ensure that there is no electrostatic discharge and component damage.
2. Static electricity is the biggest danger to the PCB parts you are about to disassemble or assemble. Its important
to use your anti-static wrist strap to prevent damage to these components.
3. Dismantling a discrete electronic component such as main capacitor is dangerous.
The capacitor contains high voltage, which can cause a severe electric shock if you touch it. This holds a
charge even when the unit is not plugged in and is capable of delivering a fatal shock.
4. Using excessive force during disassembly and assembly can damage locking parts. Use care when handling
Locking parts to avoid damage to FPCB or wire. Apply pressure only at the points designated in the maintenance
instructions.
5. Due to increasing environmental concerns, a number of restrictions have been placed on the material contentof electronic components and electronic assemblies. It requires utilizing Lead-Free (Pb-free) Soldering.
6. The following precautions must be observed when handling such components below.
CAUTION!
8/11/2019 ST71T_ENG
8/74
Product specications
Copyright 1995-2013 SAMSUNG. All rights reserved. 2-1
2. Product specifications
2-1 Specifications
Image sensor
Type 1/2.3 (Approximately 7.77 mm) CCD
Effective pixels Approximately 16.1 mega-pixels
Total pixels Approximately 16.6 mega-pixels
Lens
Focal lengthSamsung Lens f = 4.522.5 mm
(35 mm lm equivalent: 25125 mm)
F-stop range F2.5 (W)F6.3 (T)
Zoom
Still image mode: 1.05.0X
(Optical zoom X Digital zoom: 50.0X, Optical zoom X Intelli zoom: 20.0X)
Playback mode: 1.014.4X (depending on image size)Display
Type TFT LCD
Feature 2.7 (67.5 mm) QVGA (230K)
Focusing
Shutter speed
Smart Auto: 81/2,000 sec.
Program: 11/2,000 sec.
Night: 81/2,000 sec.
Exposure
ISO equivalent Auto, ISO 80, ISO 100, ISO 200, ISO 400, ISO 800, ISO 1600, ISO 3200Flash
Range Wide: 0.34.2 m (ISO Auto) Tele: 0.51.6 m (ISO Auto)
Shake reduction
Type Digital Image Stabilization (DIS)
Storage
Media
Internal memory: Approximately 70 MB
External memory (Optional):
- microSD card (2 GB guaranteed),
- microSDHC card (up to 8 GB guaranteed)
Interface
Digital output connector USB 2.0
DC power input connector 5 V
Power source
Rechargeable battery Lithium-ion battery (BP70A, 700 mAh)
Connector Type Micro USB (5 pin)
Wight & Dimensions
Wight 90 g (without battery and memory card)
Dimensions 91.6 X 55.2 X 17.5 mm (without protrusions)
8/11/2019 ST71T_ENG
9/74
Product specications
2-2 Copyright 1995-2013 SAMSUNG. All rights reserved.
2-2 Product comparison
Model
SpecsES95/ES96/ES99/ST71T ST66/ST68
Product
image
Image Sensor 1/2.3 (Approximately 7.77 mm) CCD 1/2.3 (Approximately 7.76 mm) CCD
Effective pixels Approximately 16.1 mega-pixels Approximately 16.1 mega-pixels
Total pixels Approximately 16.6 mega-pixels Approximately 16.4 mega-pixels
Wight 90 g (without battery and memory card) 101 g (without battery and memory card)
Dimensions
(W X H X D)91.6 X 55.2 X 17.5 mm (without protrusions) 90.9 X 53.9 X 16.9 mm (without protrusions)
LCD TFT LCD, 2.7 (67.5 mm) QVGA (230K) TFT LCD, 2.7 (6.9 cm) QVGA (230K)
Focal LengthSamsung Lens f = 4.522.5 mm
(35 mm lm equivalent: 25125 mm)
Samsung Lens f = 4.522.5 mm
(35 mm lm equivalent: 25125 mm)
Zoom Still image mode: 1.05.0X Playback mode: 1.014.4X
Still image mode: 1.05.0X Playback mode: 1.014.4X
Shutter Speeds
Smart Auto: 81/2,000 sec.
Program: 11/2,000 sec.
Night: 81/2,000 sec.
Smart Auto: 81/2,000 sec.
Program: 11/2,000 sec.
Night: 81/2,000 sec.
ISO RangeAuto, ISO 80, ISO 100, ISO 200, ISO 400, ISO 800,
ISO 1600, ISO 3200
Auto, ISO 80, ISO 100, ISO 200, ISO 400, ISO 800,
ISO 1600, ISO 3200
Storage
Internal memory: Approximately 70 MB
External memory (Optional): - microSD card (2 GB guaranteed),
- microSDHC card (up to 8 GB guaranteed)
Internal memory: Approximately 70 MB
External memory (Optional): - microSD card (2 GB guaranteed),
- microSDHC card (up to 8 GB guaranteed)
Shake reduction Digital Image Stabilization (DIS) Digital Image Stabilization (DIS)
Connector type Micro USB (5 pin) Micro USB (5 pin)
Battery Source Lithium-ion battery (BP70A, 700 mAh) Lithium-ion battery (BP70A, 700 mAh)
8/11/2019 ST71T_ENG
10/74
Product specications
Copyright 1995-2013 SAMSUNG. All rights reserved. 2-3
2-3 Accessories information
image Description Parts No.
Packingitems
CameraES95/ES96/ES99/ST71T
AC adapter
AD5055_EXP AD44-00183A
AD5055_WH_EXP AD44-00213A
AD5055_CHI AD44-00184A
AD5055_WH_CHI AD44-00214A
AD5055_USA AD44-00179A
AD5055_WH_USA AD44-00209A
AD5055_UK AD44-00182A
AD5055_WH_UK AD44-00212A
AD5055_AUS AD44-00185A
AD5055_WH_AUS AD44-00215A
AD5055_ARG AD44-00181A
AD5055_WH_ARG AD44-00211A
AD5055_INDIA AD44-00205A
AD5055_WH_INDIA AD44-00216A
AD5055_BRA AD44-00180A
AD5055_WH_BRA AD44-00210A
USB cableCB5MU05E AD39-00190A
CB5MU05E_WH AD39-00202A
Battery AD43-00194A
Strap
BLACK AD63-07111A
WHITE AD63-07284A
SILVER AD63-07112A
Quick Start Guide
MANUAL-ES95_SCHI AD68-07689A
MANUAL-ES95_EUR1 AD68-07690A
MANUAL-ES95_EUR2 AD68-07691A
MANUAL-ES95_EUR3 AD68-07692A
MANUAL-ES95_ASIA AD68-07693A
MANUAL-ES95_CANADA AD68-07694AMANUAL-ES95_SEA AD68-07695A
MANUAL-ES95_TUR AD68-07696A
8/11/2019 ST71T_ENG
11/74
Product specications
2-4 Copyright 1995-2013 SAMSUNG. All rights reserved.
image Description Parts No.
Optional
items
Camera case
CC9S71N AD69-03285A
CC9S70B AD69-03284A
CC9S30B AD69-03283A
CC9U21B/P
AD69-02964A
AD69-03010A
CC9U11B AD69-02397B
Battery charger BC9UA3 AD44-00164A
microSD card
2G 1109-001378
4G 1109-001420
8G 1109-001396
Card Adaptor 3719-001319
8/11/2019 ST71T_ENG
12/74
Product specications
Copyright 1995-2013 SAMSUNG. All rights reserved. 2-5
2-4 About the memory card
The memory capacity may dier depending on the scenes you shoot or shooting conditions.
These capacities are based on a 2 GB microSD card:
Size Super Fine Fine Normal
P
h
o
t
o
s
213 417 616
244 476 693
283 559 824
337 656 953
649 1,220 1,743
1,052 1,906 2,653
1,743 2,905 3,813
3,211 5,085 6,102
Size 30 fps 15 fps
V
i
d
e
o
s
Approx. 08' 07" Approx. 15' 03"
Approx. 18' 42" Approx. 36' 06"
Approx. 66' 39" Approx. 120' 55"
The gures above are measured without using the zoom function.
Available recording time may vary if you use the zoom.
Several videos were recorded in succession to determine the total recording time.
8/11/2019 ST71T_ENG
13/74
Product specications
2-6 Copyright 1995-2013 SAMSUNG. All rights reserved.
2-5 About the battery
Specication Description
Model BP70A
Type Lithium-ion battery
Cell capacity 700 mAh
Voltage 3.7 V
Charging time*(when the camera is switched off) Approximately 160 min
* Charging the battery by connecting it to a computer may take longer.
Average shooting time/ Number of photos Test conditions (when the battery is fully charged)
PhotosApproximately 140min/
Approximately 280 photos
The battery life was measured under the following conditions: in mode,
in darkness, resolution, Fine quality, DIS on.
1. Set the ash option to Fill in, take a single shot, and zoom in or out.
2. Set the ash option to Off, take a single shot, and zoom in or out.
3. Perform steps 1 and 2, waiting 30 seconds between each step.
Repeat the process for 5 minutes, and then turn off the camera for 1 minute.
4. Repeat steps 1 to 3.
Videos Approximately 110 min Record videos at resolution and 30 FPS.
The gures above are measured by Samsungs standards. Your results may differ, depending on youractual usage.
Several videos were recorded in succession to determine the total recording time.
8/11/2019 ST71T_ENG
14/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-1
Disassembly and reassembly
3. Disassembly and reassembly
3-1 Disassembly of main unit
1. Remove the 1 screw on the left side, 2 screws on the right side and 2 screws on the bottom side.
Fig. 3-1
SCREW-MACHINE6001-002640
SCREW-MACHINE
6001-002640
8/11/2019 ST71T_ENG
15/74
Disassembly and reassembly
3-2 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-3
Fig. 3-2
2. Run a safe open pry tool around the join of LOCKING PART to release the ASSY COVER BACK as illustrated in image.
Slightly wiggle the LOCKING PART to widen the gap. You'll have to apply a little force to remove it.
3. Remove the ASSY COVER BACK.
ASSY COVER BACK
ASSY COVER BACK
8/11/2019 ST71T_ENG
16/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-3
Disassembly and reassembly
Fig. 3-4
Fig. 3-5
4. Remove the FPCB from the connector as illustrated in image A.
5. Remove the ASSY PCB KEY.
CAUTION!
Use care no to damage FPCB when removing FPCB from the connector.
1. It is installed. 2. Remove.Image A
Remove the FPCB.
FPCB
FPCB
ASSY PCB KEY
8/11/2019 ST71T_ENG
17/74
Disassembly and reassembly
3-4 Copyright 1995-2013 SAMSUNG. All rights reserved.
6. Remove the FPCB from the connector as illustrated in image B.
7. Remove the LCD.
Fig. 3-6
Fig. 3-7
CAUTION!
Use care no to damage FPCB when removing FPCB from the connector.
Remove the FPCB from the connector.
1. Open.
2. Remove.
FPCB
FPCB
Image B
LCD
8/11/2019 ST71T_ENG
18/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-5
Disassembly and reassembly
Fig. 3-8
Fig. 3-9
9. Remove the FRAME-MAIN.
8. Remove the 3 screws.
SCREW-TAPTYPE6003-001630
FRAME-MAIN
8/11/2019 ST71T_ENG
19/74
Disassembly and reassembly
3-6 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-10
Fig. 3-11
10. Remove the FPCB as illustrated in image C.
11. Remove the ASSY BARREL PCB MAIN.
CAUTION!
Use care no to damage FPCB when removing FPCB from the connector.
Remove the FPCB from the connector.
1. Open.
2. Remove.
FPCB
FPCB
Image C
ASSY BARREL PCB MAIN
8/11/2019 ST71T_ENG
20/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-7
Disassembly and reassembly
Fig. 3-13
12. Remove the 2 FPCBs as illustrated in image D.
13. Remove the ASSY BARREL from the ASSY PCB MAIN.
Fig. 3-12
CAUTION!
Use care no to damage FPCB when removing FPCB from the connector.
1. Open. 2. Remove.
Remove the FPCB from the connector.
FPCBFPCB
Image D
ASSY BARREL ASSY PCB MAIN
8/11/2019 ST71T_ENG
21/74
Disassembly and reassembly
3-8 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-14
Fig. 3-15
14. Remove the ASSY COVER FRONT.
ASSY COVER FRONT
15. Discharge the part marked in red circle.
CAUTION!
Discharge the condenser.
Discharging
8/11/2019 ST71T_ENG
22/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-9
Disassembly and reassembly
16. Remove the 2 locking parts with tweezers marked in green circle.
Fig. 3-16
Fig. 3-17
17. Remove the ASSY TOP PCB.
ASSY TOP PCB
8/11/2019 ST71T_ENG
23/74
Disassembly and reassembly
3-10 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-19
18. Remove the 3 screws.
19. Remove the ASSY PCB FPC-CCD.
Fig. 3-18
SCREW-TAPTYPE6003-001369
ASSY PCB FPC-CCD
8/11/2019 ST71T_ENG
24/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-113-11
Disassembly and reassembly
Fig. 3-21
Fig. 3-20
3-2 Disassembly of barrel
1.Remove the 5 screws.
SCREW-TAPTYPE6003-001630
2. Remove the screw.
SCREW-TAPTYPE6003-001369
8/11/2019 ST71T_ENG
25/74
Disassembly and reassembly
3-12 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-23
Fig. 3-22
3. Remove the 4 solders marked in red rectangle as illustrated in image A.
4. Remove the locking part with tweezers as illustrated in image B.
CAUTION!
Use care not to damage the surrounding circuit element and other components when removing the solder.
Image B
Image A
5. Remove the ASSY BASE-LENS.
ASSY BASE-LENS
8/11/2019 ST71T_ENG
26/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-133-13
Disassembly and reassembly
Fig. 3-24
6. Pull the FPCB in the direction of the arrow and remove it as illustrated in image c.
Image C
7. Turn the part marked by finger tip fully clockwise and remove the BARREL-BASE as illustrated in image D.
Fig. 3-25
BARREL BASE
Image D
8/11/2019 ST71T_ENG
27/74
Disassembly and reassembly
3-14 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-26
8. Turn the part marked by finger tip fully counterclockwise and remove the ASSY SUB BARREL-OUTERCAM as illustrated in image E.
ASSY SUB BARREL-OUTERCAM
Image E
Fig. 3-27
9. Move the part marked byin the direction of the arrow and remove the BARREL-OUTER GUIDE as illustrated in image F.
BARREL-OUTER GUIDE
Image F
8/11/2019 ST71T_ENG
28/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-153-15
Disassembly and reassembly
Fig. 3-28
10. Turn the part fully counterclockwise and remove the ASSY SUB BARREL-ZOOMRING as illustrated in image G.
ASSY SUB BARREL-ZOOMRINGImage G
Fig. 3-29
11. Remove the BARREL-INNER CAM.
BARREL-INNER CAM
8/11/2019 ST71T_ENG
29/74
Disassembly and reassembly
3-16 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-30
12. Remove the PLATE-INNER GUIDE.
PLATE-INNER GUIDE
1. Type of lubricant
Lubricant brand name : Kanto Kasei (http://www.kanto-kasei.co.jp/e/index.html)
Please contact us (KIHYUNG CO.,LTD Distributor) by email if you are interested in purchasing.
e-mail : [email protected]
Anti-friction lubricant serves to prevent from the possibility of defective parts.
Replacement parts are required to apply the lubricant before installing the ASSY BARREL.
3-3-1 How to use the lubricant for anti-friction to the ASSY BARREL assembly
3-3 Reassembly of barrel
Component Name Where to apply Name of lubricant
Lens Base Sliding contact surfaces of AF Lens. Grease KG-513
Others components Inside and outside friction surface HANARL UD-420K
HANARL is volatile product. Keep its container tightly covered.
Make sure to shake the HANARL well first before you use it because it has a lot of particles
in the bottom. (Otherwise it becomes ineffective.)
Shake the HANARL until there are no lumps at all and apply it with brush.
CAUTION!
8/11/2019 ST71T_ENG
30/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-173-17
Disassembly and reassembly
2. Instructions
1) Lubricating with HANARL: Sliding contact surfaces of AF Lens.
Applying the Grease
1) Apply the Grease KG-513 to the two pins of AF Lens.
2) Do not get any Grease on the AF lens.
3) Apply a light coating of the Grease KG-513 and make sure not to get any on the AF lens and other components.
Apply Grease
Apply Grease
Fig. 3-31
2) Lubricating with HANARL: Others components
Apply the HANARL to the Inside and outside friction surface of the components such as ZOOMRING,
CAM BARREL, GUIDE PLATE as illustrated in image below.
HANARL is volatile product. Keep its container tightly covered.
Make sure to shake the HANARL well first before you use it because it has a lot of particles
in the bottom. (Otherwise it becomes ineffective.)
Shake the HANARL until there are no lumps at all and apply it with brush.
CAUTION!
Fig. 3-32
BARREL BASE
Inside surface
thoroughly
ASSY SUB BARREL-OUTERCAM
Inside surface
thoroughly
8/11/2019 ST71T_ENG
31/74
Disassembly and reassembly
3-18 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-33
ASSY SUB BARREL-ZOOMRING
MOVE PIN
Inside and outside
surface thoroughly
BARREL-INNER CAM
Inside and outside
surface thoroughlyPin sliding
contact surface
BARREL-OUTER GUIDE
8/11/2019 ST71T_ENG
32/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-193-19
Disassembly and reassembly
Fig. 3-35
3-3-2 Reassembly of barrel
Fig. 3-34
1. Align the parts marked by,& respectively as illustrated in image A. Then install the PLATE-INNER GUIDE .
2. Align the parts marked by,&respectively as illustrated in image B. Then install the BARREL-INNER CAM.
PLATE-INNER GUIDE
Image A
BARREL-INNER CAM
Image B
8/11/2019 ST71T_ENG
33/74
Disassembly and reassembly
3-20 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-36
3. Align the parts marked byas illustrated in image C.4. Turn the part fully clockwise and remove the ASSY SUB BARREL-ZOOMRING as illustrated in image D.
ASSY SUB BARREL-ZOOMRING
Image D
Image C
8/11/2019 ST71T_ENG
34/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-213-21
Disassembly and reassembly
5. Close the space between the part&as illustrated in image E.
6. Align the parts marked by,&respectively as illustrated in image F. Then install the BARREL-OUTER GUIDE.
Fig. 3-37
BARREL-OUTER GUIDE
Image E Image F
8/11/2019 ST71T_ENG
35/74
Disassembly and reassembly
3-22 Copyright 1995-2013 SAMSUNG. All rights reserved.
7. Align the parts marked by,&respectively as illustrated in image G.8. Turn the part fully counterclockwise and remove the ASSY SUB BARREL-OUTERCAM as illustrated in image H.
Fig. 3-39
Fig. 3-38
Image G
9. Align the parts marked by,,,,&respectively as illustrated in image I. Then install theBARREL-BASE.
ASSY SUB BARREL-OUTERCAM
Image H
BARREL BASE
Image I
8/11/2019 ST71T_ENG
36/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-233-23
Disassembly and reassembly
Fig.3-40
Fig.3-41
10. Connect the FPCB as illustrated in image J.
11. Align the parts marked by & respectively as illustrated in image K. Then install the ASSY BASE-LENS.
2.Align the parts marked by to install.
1. Pull the FPCB in the direction of the arrow. Image J
ASSY BASE-LENSAlign the parts marked by to install.
Align the parts marked by to install.
Image K
8/11/2019 ST71T_ENG
37/74
Disassembly and reassembly
3-24 Copyright 1995-2013 SAMSUNG. All rights reserved.
Fig. 3-43
Fig. 3-42
13.Tighten the screw.
1 2.Solder the 4 places marked in red rectangle as illustrated below.
CAUTION!
Use care not to damage the surrounding circuit element and other components when soldering.
SCREW-TAPTYPE6003-001369
8/11/2019 ST71T_ENG
38/74
Copyright 1995-2 013 SAMSUNG. All rights reserved. 3-253-25
Disassembly and reassembly
Fig. 3-44
14.Tighten the 5 screws.
SCREW-TAPTYPE6003-001630
8/11/2019 ST71T_ENG
39/74
Troubleshooting
Copyright 1995-2013 SAMSUNG. All rights reserved. 4-1
4. Troubleshooting
4-1 Regarding to memory card recognition
Symptom Explanation/Solution Note
Memory card
is not recognized.
Check the PAD of SD card.
Place the memory card on a table
in front of you with the metal contacts
facing up. Scrub the contact area with
your brush, wiping away any corrosion,
dirt or grime on the contacts.
Recheck if the Memory Card is being
recognized.
Check the mechanical failure of
SD card socket of Main PCB.
Check the SMD and other surrounding
components.
8/11/2019 ST71T_ENG
40/74
Troubleshooting
4-2 Copyright 1995-2013 SAMSUNG. All rights reserved.
4-2 Regarding to MAIN PCB connection
Symptom Explanation/Solution Note
Power does not work.
1. Check the connection between
MAIN PCB and TOP PCB.
2. Check the connection of Lens(BARREL)FPCB.
3. Check the connection of Sensor CCD
FPCB.
LCD does not display
anything or display white.1. Check the connection of LCD FPCB.
Rear key will not input
correctly.
3. Check the connection of KEY FPCB.
4-3 Regarding to TOP switch (Power/Shutter/Zoom)
Symptom Explanation/Solution Note
Power and Shutter
do not work.
Check the connection between MAIN PCBand TOP PCB.
Check the SMD of power and shutter switch.Check whether there is mechanical failure.
8/11/2019 ST71T_ENG
41/74
Troubleshooting
Copyright 1995-2013 SAMSUNG. All rights reserved. 4-3
4-4 Regarding to flash
Symptom Explanation/Solution Note
Flash and charging
do not work.
Check the connection of between MAIN PCB and
TOP PCB.
Make sure XE-Tube is inserted properly.From the front view, make sure it is Negative end
on the right side.
Check the positive and negative ends on Main Condenser.
(Make sure it is Negative end as illustrated in redrectangle.)
Check the soldering of Popup Module and SMDof Trigger Coil.
Check the transformer of SMD.
8/11/2019 ST71T_ENG
42/74
Troubleshooting
4-4 Copyright 1995-2013 SAMSUNG. All rights reserved.
4-5 Regarding to image display
Symptom Explanation/Solution Note
It is displayed
vertical and
horizontal line noise
and afterimage.
Check the connection of SMD of CCD
connector and FPCB.
Check the CCD sensor and FPCB.If the CCD sensor and FPCB are damaged,replace and recheck them.
Check the connection of SMD of LCDconnector and FPCB.
4-6 Regarding to voice playback and recording
Symptom Explanation/Solution Note
Can not hear anything.
Check the soldering of speaker wire.- Whether it is connected negative or positiveproperly.- Whether the wire is down or wire soldering
comes off.
There is sound
when pressing button.
However, voice
recording
does not work.
Check the soldering of FPCB.- Whether it is connected negative or positiveproperly.
- Where FPCB is torn.
8/11/2019 ST71T_ENG
43/74
PCB diagrams
Copyright 1995-2013 SAMSUNG. All rights reserved. 5-1
5. PCB diagrams
5-1 MAIN PCB
BOTTOMTOP
8/11/2019 ST71T_ENG
44/74
PCB diagrams
5-2 Copyright 1995-2013 SAMSUNG. All rights reserved.
5-2 TOP PCB
TOP BOTTOM
8/11/2019 ST71T_ENG
45/74
8/11/2019 ST71T_ENG
46/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 7-1
Firmware update
7-1 Product reset
1. Press the power button to turn on the camera.
This describes how to reset the camera to factory default setting.
7. Firmware update
Fig. 7-1
Fig. 7-2
2. While pressing the zoom out(-) button and down button on the 4-way button, hold and press the power button.
POWER BUTTON
POWER BUTTON2 ZOOM OUT(-) BUTTON & DOWN BUTTON ON THE 4-WAY BUTTON1
ZOOM OUT(-) BUTTON DOWN BUTTON ON THE 4-WAY BUTTON
8/11/2019 ST71T_ENG
47/74
Firmware update
7-2 Copyright 1995-2013 SAMSUNG. All rights reserved.
3. Press the power button to set the default value.
Fig. 7-3
Settings
Language
Time Zone
Date/Time Set
Date Type
Exit ChangeMENU
Settings
Language
Time Zone
Date/Time Set
Date Type
Exit ChangeMENU
8/11/2019 ST71T_ENG
48/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 7-3
Firmware update
7-2 Version check
This describes how to check the version of the current rmware of the camera.
1. Before upgrading your cameras rmware, make sure the battery is fully charged.
2. Press the power button to turn o the camera.
4. The current rmware version will be displayed on the LCD. Press the power button to exit.
Fig. 7-5
Fig. 7-4
3. While pressing the shutter button and down button on the 4-way button, press the power button.
The cameras rmware version will be displayed on the LCD.
SHUTTER BUTTON DOWN BUTTON ON THE 4-WAY BUTTON
2 POWER BUTTON SHUTTER BUTTON & DOWN BUTTON ON THE 4-WAY BUTTON1
F/W VERSION: 1211 071- (CPT) (ND8) (CF)
1301.04Cb.0077
S/N: A0013CBH700369C
Barrel S/N: 090002914419000061
D0: 20948 OK PD0: 124 OK
D1: 29964 OK PD2: 204 OK
CSH: 11/11/11 OK
8/11/2019 ST71T_ENG
49/74
Firmware update
7-4 Copyright 1995-2013 SAMSUNG. All rights reserved.
7-3 Firmwawre update
Firmware execution information
The below table provides the information of rmware structure. Code section contains the execution code to operate the camera.The partition 1 to 3 sections contain the all the resources to operate the camera. Partition 3 section contains the defective pixel adjustment data
and lens shading adjustment data. User Area contains the setting value when user sets up the setting by the menu button.
Also, User Area section contains the adjustment data through the adjustment process.
Reference of general version:- It updates data contained in the Code and partition 1 section while partition 3 and User Area section data remain.
1. Format the memory card. Copy the two below les such as ES95-dsp-1211271-full.elf and fwup.txt
into the memory card. Then insert the memory card into the camera.
* When the rmware is updated, all the camera settings are set to their default values.
Since all the les stored in the internal memory will be deleted, ensure that les are copied to other storage devices
before updating rmware.
2. It is recommended that you use an AC adaptor or the fully charged batteries. * Before upgrading your cameras rmware, make sure the battery is fully charged.
3. Press the power button to turn on the camera.
Code partition1 partition2 partition3 User Area
Fig. 7-6
This section describes how to update the rmware.
fwup.txt
ES95-dsp-1211271-full.elf
POWER BUTTON
8/11/2019 ST71T_ENG
50/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 7-5
Firmware update
4. The rmware version will be displayed on the LCD screen.
Press the shutter button to start the rmware update process.
6. Once the rmware update is complete, the camera will automatically power o.
5. It takes about 2 minute to complete the process.
Fig. 7-7
Fig. 7-8
SHUTTER BUTTON
Firmware upgrade
DSP : full 1211071-U -> 1211271-U
OIS
Press the shutter button to upgrade the frmware.
Firmware is updating...
The camera will turn o automatically
after the upgrade is complete.
Do not power o during the process.
8/11/2019 ST71T_ENG
51/74
Firmware update
7-6 Copyright 1995-2013 SAMSUNG. All rights reserved.
7-4 Main PCB recovery
This section describes how to update the rmware when camera stops functioning due to power failure or some other reasons
during the rmware process.All of the adjustment data will be deleted when forced to quit. Therefore you have to go over all the adjustment process again.
1. microSD card
- Less than 1GB microSD card is recomanded.
2. Soldering iron
- To short out the circuit for TP(Test Point).
3. The latest rmware le: ES95-dsp-1211271-full.elf & fwup.txt
- The rmware le is available to download from k-zone or Samsungs site.
- Firmware le name varies by model. Conrm that the rmware le is the correct for update.
You will need:
1. Remove the back cover, key FPCB, LCD and main frame as illustrated in Fig. 7-9.
2. Solder the test point (TP) marked in red circle on Main PCB to short out the circuit.
3. Copy the rmware les to the root of microSD card .
4. Insert the memory card containing the rmware into the camera memory card slot.
* Make sure to fully charge the battery of a type supported by the camera.
5. Turn on the camera to start the rmware update process. LED will blink while the rmware update is processing.
It may take about 2 minutes.
6. LED will stop blinking when the rmware update is completed.
7. Once the process is complete, disassemble the camera and remove the solder of the test point (TP) on Main PCB.
8. Assemble the camera. Turn on the camera and test that the camera works properly.
Fig. 7-9
Position for soldering
8/11/2019 ST71T_ENG
52/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 8-1
Adjustment
8. Adjustment
After replacing the parts, you need to adjust the following items.
The table below provides information about the necessary adjustment process.
1. Please refer to the table information before beginning the adjustment process.
2. Necessary equipment
1) Light source box: Light source box is used to adjust the luminance level and the color temperature of the Light box.
It helps adjust the luminance level to 12LVandcolor temperature of the Light box to 3300K.
2) Innity Collimator for PUNT adjustment 6LV
3) 18% Reectance gray chart for FLASH adjustment and Dark Box.
4) POWER SUPPLY: 4.2V/2A
3. Adjustment le
It is necessary to copy the adjustment le such asES95_ADJ.TXT into the memory card to proceed the each process.
4. Proceed with the steps listed below in order to complete the adjustment process.
1) LENS SHADING ADJ (Color Shading) 2) SHUTTER CLOSE TIME ADJ
3) FLASH ADJ
4) PUNT ADJ
5) CCD DEFECT PIXEL ADJ
6) BACKLASH ADJ
7) CVERTICAL LINE ADJ
8) SERIAL NUMBER WRITING ADJ
8-1 Basic guide for adjustment
Main PCB POWER PCB BARREL ASSY CCD ASSY
FIRMWARE UPGRADE O X X X
LENS SHADING ADJ (Color Shading) O X O O
SHUTTER CLOSE TIME ADJ O X O O
FLASH ADJ O O O O
PUNT ADJ O X O O
CCD DEFECT PIXEL ADJ O X O O
BACKLASH ADJ O X O O
VERTICAL LINE ADJ O X O O
SERIAL NUMBER WRITING ADJ O X X X
8/11/2019 ST71T_ENG
53/74
Adjustment
8-2 Copyright 1995-2013 SAMSUNG. All rights reserved.
5. Stages of the adjustment process is described below.
Insert the memory card into camera.
Turn on the camera.
Adjustment process begins in test mode.
Check the process ID.
Pass / No pass
Begin the each process.
Adjustment data is stored
in EEPROM.
Adjustment data and OK message
are displayed on LCD.
Set process ID. (EEPROM)
Turn off automatically or
continue to proceed the process.
Record log le.
(If necessary)
Adjustment value and OK message
are displayed on LCD.
Turn off or stand by.
Final successful process I D
is displayed.
Store the adjustment data
in EEPROM. (If necessary)
No
No
Yes
Yes
8/11/2019 ST71T_ENG
54/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 8-3
Adjustment
This section describes how to adjust the Lens shading.
< Adjustment method >
NOTE: Light source box is used to adjust the luminance level and the color temperature of the Light box.Light source box helps adjust the luminance level of the Light box to 12LVandcolor temperature of the Light box to 3300K.
Please follow the instruction to begin the process.
1. Copy the ES95_ADJ.TXT le into the memory card and insert it into the camera.
2. Mount the camera on Light source box. Press the power button to open the lens tube.
Set the distance between the rear of the lens tube and the light box to 10mm 1mm.
3. Set the luminance level of the Light source box to 12LV.
4. Once the camera is turned on by pressing the power button, the process will begin automatically.
1) The iris and zoom is set to zero.
2) Refer to the EEPROM WRITE information and write the adjustment value to EEPROM.
3) Refer to the CARD WRITE information and write the adjustment value to the data le.
4) Set the USL(Upper Specication Limit) and LSL(Lower Specication Limit).
5. Once the process is completed, the camera will automatically turn off.
< Adjustment result >Double-click the memory card folder to view the result. You will find the generated CSV file in the folder. Click the f ile to check the generated
content.
Fig. 8-1
8-2 LENS SHADING ADJ (Color Shading)
Back view of light source box
Light source box
Camera
Tripod
8/11/2019 ST71T_ENG
55/74
Adjustment
8-4 Copyright 1995-2013 SAMSUNG. All rights reserved.
8-3 SHUTTER CLOSE TIME ADJ
This section describes how to adjust Shutter close time.
It generates the relative tolerance. This adjustment process help reduce the tolerances for better performance.
Itproceeds CCD Gain adjustment process simultaneously.
4. Once the camera is turned on by pressing the power button, the process will begin automatically.
1) The Line delay and Sub delay are adjusted to the luminance level range of 12LV.
2) If the value of the Line delay is in the range of the minimum and maximum value, the result is OK. Otherwise, it is NG.
3) Refer to the EEPROM WRITE information and write the adjustment value to EEPROM.
4) Refer to the CARD WRITE information and write the adjustment value to the data le.
5. Once the process is completed, the camera will automatically turn off.
< Adjustment result >
Double-click the memory card folder to view the result. You will find the generated CSV file in the folder.
Click the file to check the generated content.
Fig.8-2
< Adjustment method >
NOTE: Light source box is used to adjust the luminance level and the color temperature of the Light box.
Light source box helps adjust the luminance level of the Light box to 12LVandcolor temperature of the Light box to 3300K.
Please follow the instruction to begin the process.
1. Copy the ES95_ADJ.TXT le into the memory card and insert it into the camera.
2. Mount the camera on Light source box. Press the power button to open the lens.
Set the distance between the rear of the lens and the light box to 10mm 1mm.
3. Set the luminance level of the Light source box to 12LV.
Back view of light source box
Light source box
Camera
Tripod
8/11/2019 ST71T_ENG
56/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 8-5
Adjustment
8-4 FLASH ADJ
This section describes how to adjust the Flash and AWB.
It test the brightness of Strobe within the certain limit of the luminance level to verify that a product works properly.
It proceeds the AWB HIGH adjustment process simultaneously.
1. Set the 18% Reflectance gray card on the wall in the darkroom.
2. Copy the ES95_ADJ.TXT le into the memory card and insert it into the camera. Mount the camera on Dark Box.
3. Set the distance between the reflective paper and camera to 50cm.
4. Once the camera is turned on by pressing the power button, the process will begin automatically.
1) Refer to the Table 8-2. It provides the information of the adjustment process.
Proceed the process twice in a raw. If the value is the range of the standard luminance level, it assures overall hardware quality is good.
2) Average out the two test values. Then check the R gain and B gain to verify the quality of hardware.
3) Refer to the EEPROM WRITE information and write the adjustment value to EEPROM.
4) Write the R. B gain to the EEPROM if the hadware quality test is passed sucessfully.
5. Once the process is completed, the camera will automatically turn off.
< Adjustment result >
Double-click the memory card folder to view the result. You will find the generated CSV file in the folder.
Click the file to check the generated content.
Fig. 8-3
50cm
18% Reflectance gray card
Camera
Tripod
8/11/2019 ST71T_ENG
57/74
Adjustment
8-6 Copyright 1995-2013 SAMSUNG. All rights reserved.
8-5 PUNT ADJ (A F)
This section describes how to adjust the PUNT. After replacing the MAIN PCB and BARREL, you must decide the AF search range,
allowing focus to be properly adjusted for the best picture quality.
Necessary equipment: Innity Collimator/ Innity Subject
(Proceed through the adjustment process with Innity Collimator or Innity Subject as illustrated below.)
< With Innity Collimator >
1. Copy the ES95_ADJ.TXT le into the memory card and insert it into the camera.
2. Please follow the instruction below to begin the punt adjustment process.
1) Innity Collimator Specications
- Set the luminance level to 6LV.
- Set the distance as less than 1cm between the end of camcorder lens and lens surface of the innity Collimator.
- Do not remove the camcorder from tripod during the process.
Fig. 8-4
Infinity Collimator
Camera
Tripod
8/11/2019 ST71T_ENG
58/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 8-7
Adjustment
< With Subject Specications >
2) Innity Subject Specications
- Secure the camcorder on the tripod and adjust the height.
- Focus on a subject at innity which is more than 500m away.
- Choose a subject where it is essentially innitely far away such as apartment or church as illustrated below.
3. Press the power button to turn on the camera.
4. The adjustment process will automatically begin.
Double-click the memory card folder to view the result. You will find the generated CSV file in the folder.
Click the file to check the generated content.
Fig. 8-5
CAUTION!
Try not to attempt the adjustment process during the night. It may generate the inaccurate test result
due to the difculty of auto focus. If you want to proceed the process, choose a subject such as glass building
making the contrast level low.
Camera
Tripod
Center your subject in the frame.
Make sure the subject t within the 1/5
of the little rectangle around your viewnder.
8/11/2019 ST71T_ENG
59/74
Adjustment
8-8 Copyright 1995-2013 SAMSUNG. All rights reserved.
8-6 CCD DEFECT PIXEL ADJ (DPC)
1.Copy the ES95_ADJ.TXT le into the memory card and insert it into the camera.
2. Once the camera is turned on by pressing the power button, the process will begin automatically.
1) Check the data such as reference level, exposure time and loop before beginning the defective pixel detection adjustment.
2) Refer to the specications about the maximum number of defective cells. Then proceed the process.
3) Refer to the CARD WRITE information and write the number of defective cells to the data le.
3. Once the process is completed, the camera will automatically turn off.
Double-click the memory card folder to view the result. You will find the generated CSV file in the folder.
Click the file to check the generated content.
This section describes how to adjust the defective pixel detection for CCD image sensor.
8/11/2019 ST71T_ENG
60/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 8-9
Adjustment
1.Copy the ES95_ADJ.TXT le into the memory card and insert it into the camera.
2. Once the camera is turned on by pressing the power button, the process will begin automatically.
1) Close the barrel.
2) Turn the barrel toward Tele. Then nd the difference of PI Count.
3) Repeat the process as much as PI Count number. Figure out the standard difference of PI Count and then average the value.
4) Check the average value is in the rage of Max_backLash.
5) Wite the log le and turn the barrel toward Wide.
3. Once the process is completed, the camera will automatically turn off.
Double-click the memory card folder to view the result. You will find the generated CSV file in the folder.
Click the file to check the generated content.
8-7 BACKLASH ADJ
This section describes how to adjust the difference when barrel is rotated different direction.
8/11/2019 ST71T_ENG
61/74
Adjustment
8-10 Copyright 1995-2013 SAMSUNG. All rights reserved.
8-8 VERTICAL LINE ADJ
Set the maximum number of vertical line to prevent displaying a big vertical line.
4. Once the camera is turned on by pressing the power button, the process will begin automatically.
1) To begin the vertical line adjustment, check the minimum and maximum value of EVC and ISO.
2) Compare the standard data with the actual test result. (Write the test result for vertical line value and ratio.)
4) Write the vertical line data for le.
5. Once the process is completed, the camera will automatically turn off.
< Adjustment result >
Double-click the memory card folder to view the result. You will find the generated CSV file in the folder.
Click the file to check the generated content.
Fig. 8-6
< Adjustment method >
NOTE: Light source box is used to adjust the luminance level and the color temperature of the Light box.
Light source box helps adjust the luminance level of the Light box to 12LVandcolor temperature of the Light box to 3300K.
Please follow the instruction to begin the process.
1. Copy the ES95_ADJ.TXT le into the memory card and insert it into the camera.
2. Mount the camera on Light source box. Press the power button to open the lens.
Set the distance between the rear of the lens and the light box to 10mm 1mm.
3. Set the luminance level of the Light source box to 12LV.
Back view of light source box
Light source box
Camera
Tripod
8/11/2019 ST71T_ENG
62/74
Copyright 1995-2013 SAMSUNG. All rights reserved. 8-11
Adjustment
8-9 SERIAL NUMBER WRITING ADJ
Serial number is provided in the cameras non-volatile memory.
A serial number is a 15-digit alphanumeric code indicated on the sticker at the bottom of a camera.
It helps to verity the authenticity of Samsung digital camera by checking the 15-digit serial number.
CAUTION!
It is necessary to proceed the serial number writing process after replacing the parts due to the Main PCB failure.
1. Generate ES95_ADJ.TXTle and copy it into the memory card.
Find the 15-digit alphanumericserial number written on the Main board.
2. Replace the Main board and insert the memory card into the camera.
3. Press the power button to turn on the camera.
4. The new serial number will be applied automatically .
5. Once the process is completed, the camera will automatically turn off.
Fig. 8-8
Fig. 8-7
A0013CBH700369Csys_serial setsys_serial get
poweroff zoom_close
POWER BUTTON
8/11/2019 ST71T_ENG
63/74
Adjustment
8-12 Copyright 1995-2013 SAMSUNG. All rights reserved.
1. Press the power button to turn off the camera.
2. While pressing the shutter button and down button on the 4-way button, press the power button.
3. Serial number will be displayed on the screen.
Fig. 8-9
SHUTTER BUTTON DOWN BUTTON ON THE 4-WAY BUTTON
2 POWER BUTTON SHUTTER BUTTON & DOWN BUTTON ON THE 4-WAY BUTTON1
F/W VERSION: 1211 071- (CPT) (ND8) (CF)
1301.04Cb.0077
S/N: A0013CBH700369C
Barrel S/N: 090002914419000061
D0: 20948 OK PD0: 124 OK
D1: 29964 OK PD2: 204 OK
CSH: 11/11/11 OK
8/11/2019 ST71T_ENG
64/74
Copyright1995-2013 SAMSUNG. All rights reserved. 9-1
Exploded view and parts list
9. Exploded view and parts list
9-1 ASSY BODY
Parts Service Information Availability
SA Service is available.
SNA Service is not available.
2
3
1
45
6
7
7
80
Loc. No. Parts No. Description Qty Available Remark
0
AD90-05318A ASSY BODY ES95 EXP_BK 1 SNA BLACK
AD90-05318B ASSY BODY ES95 EXP_WH 1 SNA WHITE
AD90-05318C ASSY BODY ES95 EXP_PK 1 SNA PINK
AD90-05318D ASSY BODY ES95 EXP_RD 1 SNA RED
1
AD97-23232A ASSY MAIN_BK 1 SNA BLACK
AD97-23232B ASSY MAIN_WH 1 SNA WHITEAD97-23232C ASSY MAIN_PK 1 SNA PINK
AD97-23232D ASSY MAIN_RD 1 SNA RED
2 AD92-02049A ASSY PCB MAIN-ES95 1 SA
3 AD61-05946A FRAME-MAIN 1 SA
4 AD92-02051A ASSY PCB KEY-ES95 1 SA
5 6003-001630 SCREW-TAPTYPE (M1.4XL3.5,BLK) 3 SA
6 AD07-00150A LCD 1 SA
7 6001-002640 SCREW-MACHINE (M1.4XL3.5,BLK) 5 SA
8 AD97-23231A ASSY COVER BACK 1 SA
8/11/2019 ST71T_ENG
65/74
Exploded view and parts list
9-2 Copyright1995-2013 SAMSUNG. All rights reserved.
2
3
1
0
9-2 ASSY MAIN
Loc. No. Parts No. Description Qty Available Remark
0
AD97-23232A ASSY MAIN_BK 1 SNA BLACK
AD97-23232B ASSY MAIN_WH 1 SNA WHITE
AD97-23232C ASSY MAIN_PK 1 SNA PINK
AD97-23232D ASSY MAIN_RD 1 SNA RED
1
AD97-23236A ASSY COVER FRONT_BK 1 SA BLACK
AD97-23236B ASSY COVER FRONT_WH 1 SA WHITE
AD97-23236C ASSY COVER FRONT_PK 1 SA PINK
AD97-23236D ASSY COVER FRONT_RD 1 SA RED
2 AD92-02050A ASSY TOP PCB 1 SA
3
AD97-23238A ASSY CHAMBER_BK 1 SNA BLACK
AD97-23238B ASSY CHAMBER_WH 1 SNA WHITE
AD97-23238C ASSY CHAMBER_PK 1 SNA PINK
AD97-23238D ASSY CHAMBER_RD 1 SNA RED
8/11/2019 ST71T_ENG
66/74
Copyright1995-2013 SAMSUNG. All rights reserved. 9-3
Exploded view and parts list
1
2
3
4
5
6
7
8 9
0
9-3 ASSY CHAMBER
Loc. No. Parts No. Description Qty Available Remark
0
AD97-23238A ASSY CHAMBER_BK 1 SNA BLACK
AD97-23238B ASSY CHAMBER_WH 1 SNA WHITE
AD97-23238C ASSY CHAMBER_PK 1 SNA PINK
AD97-23238D ASSY CHAMBER_RD 1 SNA RED
1 AD62-00216A CHAMBER BODY 1 SA
2 AD63-07358A COVER SOCKET 1 SA
3 AD61-05388A SPRING ETC-BATTERY PUSH 1 SA
4 6107-001766 SPRING-TS 1 SA
5 6044-001137 RING-E 1 SA
6 AD61-05409A BATTERY COVER HINGE-ST93 1 SA
7 AD66-00885A LEVER BATTERY LOCK 1 SA
8
AD63-07357A COVER BATTERY_BK 1 SA BLACK
AD63-07357B COVER BATTERY_WH 1 SA WHITE
AD63-07357C COVER BATTERY_PK 1 SA PINK
AD63-07357D COVER BATTERY_RD 1 SA RED
9
AD63-07365A COVER BATTERY INNER_BK 1 SA BLACK
AD63-07365B COVER BATTERY INNER_WH 1 SA WHITE
AD63-07365C COVER BATTERY INNER_PK 1 SA PINK
AD63-07365D COVER BATTERY INNER_RD 1 SA RED
8/11/2019 ST71T_ENG
67/74
Exploded view and parts list
9-4 Copyright1995-2013 SAMSUNG. All rights reserved.
1
2
3
4
5
7 6
10
9
8
0
9-4 ASSY COVER FRONT
Loc. No. Parts No. Description Qty Available Remark
0
AD97-23236A ASSY COVER FRONT_BK 1 SA BLACK
AD97-23236B ASSY COVER FRONT_WH 1 SA WHITE
AD97-23236C ASSY COVER FRONT_PK 1 SA PINK
AD97-23236D ASSY COVER FRONT_RD 1 SA RED
1 AD63-07355A COVER TOP_ES95_BK 1 SNA
2 AD64-03905A DECORATION BUTTON RELEASE 1 SNA
3 AD63-07376A T/SHEET BUTTON RELEASE 1 SNA
4 AD64-03896A BUTTON RELEASE 1 SNA
5
AD63-07354A COVER FRONT_BK 1 SNA BLACK
AD63-07354B COVER FRONT_WH 1 SNA WHITE
AD63-07354C COVER FRONT_PK 1 SNA PINKAD63-07354D COVER FRONT_RD 1 SNA RED
6 AD63-07360A T/SHEET FRONT 1 SNA
7AD64-03899A DECORATION-FRONT RING 1 SNA BLACK, RED
AD64-03899B DECORATION-FRONT RING_AL 1 SNA WHITE, PINK
8 AD63-07362A T/SHEET TOP B 1 SNA
9 AD64-03895A BUTTON POWER 1 SNA
10 AD63-07361A T/SHEET TOP A 1 SNA
8/11/2019 ST71T_ENG
68/74
Copyright1995-2013 SAMSUNG. All rights reserved. 9-5
Exploded view and parts list
1 2 3
4
0
9-5 ASSY COVER BACK
Loc. No. Parts No. Description Qty Available Remark
0 AD97-23231A ASSY BACK 1 SA
1 AD63-07356A COVER-BACK 1 SNA
2 AD64-03900A WINDOW-REAR ACCESS 1 SNA
3 AD64-03897A BUTTON-BACK 1 SNA
4 AD64-03898A BUTTON-OK 1 SNA
8/11/2019 ST71T_ENG
69/74
Exploded view and parts list
9-6 Copyright1995-2013 SAMSUNG. All rights reserved.
6
5 43
9
81
2
7
0
9-6 ASSY TOP PCB
Loc. No. Parts No. Description Qty Available Remark
0 AD92-02050A ASSY PCB TOP-ES95 1 SA
1 2401-005082 C-AL 1 SA
2 AD61-05949A HOLDER-MIC 1 SA
3 3001-002641 SPEAKER 1 SA
4 AD63-07380A CUSHION-MIC 1 SA
5 AD41-01983A FPC-TOP CONNECTION 1 SA
6 AD94-00550A ASSY SMD INSERT 1 SNA
7 AD97-23235A ASSY STROBO 1 SA
8 3003-001198 MIC-CONDENSOR 1 SA
9 AD67-02581A RUBBER-MIC 1 SA
8/11/2019 ST71T_ENG
70/74
Copyright1995-2013 SAMSUNG. All rights reserved. 9-7
Exploded view and parts list
5
2
1 3 4
57
68
0
9-7 ASSY STROBO
Loc. No. Parts No. Description Qty Available Remark
0 AD97-23235A ASSY STROBO 1 SA
1 AD61-05546A HOLDER-REFLECTOR 1 SNA
2 AD61-05550A PLATE-TRIG 1 SNA
3 AD61-05551A PLATE-XE TUBE L 1 SNA
4 AD61-05552A PLATE-XE TUBE R 1 SNA
5 AD67-02284A RUBBER-XE TUBE 2 SNA
6 AD67-02285A REFLECTOR 1 SNA
7 AD47-00024A XE TUBE 1 SNA
8 AD67-02636A LENS FRESNEL 1 SNA
8/11/2019 ST71T_ENG
71/74
Exploded view and parts list
9-8 Copyright1995-2013 SAMSUNG. All rights reserved.
8
9
10
11
12
13
14
15
16
1722
24
25
23
21
20
19
18
7
6
5
4
3
2
1
27
26
28
0
9-8 ASSY BARREL
8/11/2019 ST71T_ENG
72/74
Copyright1995-2013 SAMSUNG. All rights reserved. 9-9
Exploded view and parts list
Loc. No. Parts No. Description Qty Available Remark
0AD97-23313A ASSY BARREK CCD-ES95_BL 1 SNA BLACK : BLACK / RED
AD97-23314A ASSY BARREL CCD-ES95_SV 1 SNA SILVER : WHITE / PINK
1AD61-05936A PLATE-DECO_PET_BK 1 SA BLACK : BLACK / RED
AD61-05937A PLATE-DECO_PET_SL 1 SASILVER : WHITE / PINK
2AD97-22938A ASSY BARRIER-BLACK_D5_VE 1 SA BLACK : BLACK / RED
AD97-22939A ASSY BARRIER-LSILVER_D5_VE 1 SA SILVER : WHITE / PINK
3 AD97-21646A ASSY LENS-1ST GROUP 1 SABLACK : BLACK / RED SIL-
VER : WHITE / PINK
4AD97-22932A ASSY SUB BARREL-ZOOMRING_BLACK_D5_VE 1 SNA BLACK : BLACK / RED
AD97-22933A ASSY SUB BARREL-ZOOMRING_LSILVER_D5_VE 1 SNA SILVER : WHITE / PINK
5 AD67-02527A BARREL-INNER CAM_D5_VE 1 SNA
BLACK : BLACK / RED
SILVER : WHITE / PINK
6 AD97-21940A ASSY SUB BARREL-2ND_NON OIS 1 SABLACK : BLACK / RED
SILVER : WHITE / PINK
7 AD61-05495A PLATE-INNER GUIDE 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
8 AD67-02525A BARREL-OUTER GUIDE_D5_VE 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
9 AD63-07143A SHHET-CAM D5-VE 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
10AD67-02526A BARREL-OUTER CAM_D5_VE 1 SNA BLACK : BLACK / RED
AD67-02618A BARREL-OUTER CAM_SV_VE 1 SNA SILVER : WHITE / PINK
11 AD67-02366A BARREL-BASE 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
12 AD97-21648A ASSY LENS-3RD GROUP 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
13 AD61-05494A BASE-LENS 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
14 AD94-00254A ASSY SMD INSERT-0523-D5_NON OIS 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
15 6107-003159 SPRING-ES 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
16 AD67-01744A BARREL-DECENT_RING 1 SABLACK : BLACK / RED
SILVER : WHITE / PINK
8/11/2019 ST71T_ENG
73/74
Exploded view and parts list
9-10 Copyright1995-2013 SAMSUNG. All rights reserved.
Loc. No. Parts No. Description Qty Available Remark
17 AD63-06855A SHEET-BARREL_BASE 2 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
18 AD97-21680A ASSY ZOOM-0523-D5 1 SABLACK : BLACK / RED
SILVER : WHITE / PINK
19 AD81-04801A T/SHEET-MAIN PCB 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
20 6003-001369 SCREW-TAPTYPE(M1.4XL2.5,NI) 1 SNABLACK : BLACK / RED
SILVER : WHITE / PINK
21 AD97-21679A ASSY MOTOR 1 SABLACK : BLACK / RED
SILVER : WHITE / PINK
22 AD66-00984A SHAFT-AF GUIDE 1 SNA
BLACK : BLACK / RED
SILVER : WHITE / PINK
23 6003-001630 SCREW-TAPTYPE(M1.4XL3.5,BLK) 5 SABLACK : BLACK / RED
SILVER : WHITE / PINK
24 AD92-01928A ASSY PCB FPC-ST77VE ASSY FPCB CCD 1 SABLACK : BLACK / RED
SILVER : WHITE / PINK
25 6003-001369 SCREW-TAPTYPE(M1.4XL2.5,NI) 3 SABLACK : BLACK / RED
SILVER : WHITE / PINK
26 AD97-22941A ASSY BARREL-LSILVER_D5_VE;D5_VE,LIGHT SI 1 SA BLACK : BLACK / REDSILVER : WHITE / PINK
27AD97-21941A
ASSY LENS BASE-D5_NON OIS;D5_NON OIS,BLA 1 SABLACK : BLACK / RED
SILVER : WHITE / PINK
28 AD97-22935A ASSY SUB BARREL-FRONT_LSILVER_D5_VE;D5_V 1 SABLACK : BLACK / RED
SILVER : WHITE / PINK
8/11/2019 ST71T_ENG
74/74