Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 1 of 27
ST4000VX000
Test Report
Initiated by River Lin Approved by Jackie Wang
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 2 of 27
Revision History:
Date Revision Description Creator
2014/05/23 V1.0 The First version released. River lin
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 3 of 27
Test Results Definition:
Criteria Definition
PASS Test result pass and function work perfectly.
Fail Test fail or can not meet the spec requirement.
Limitation There are no plans to fix this function.
N/A Spec not support or driver not ready.
No Test No test tool or device or FW not ready, please write reason to the “Remark”.
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 4 of 27
Test Results Summary:
Num. Test Item Result Remark
Chapter 1 Function Test
1.01 HDD Function Test PASS
1.02 SATA IDE Mode Test PASS
1.03 SATA AHCI Mode Test PASS
1.04 SATA RAID Mode Test PASS
Chapter 2 Software Compatibility Test
2.01 OS and Driver Install Test PASS
Chapter 3 Hardware Compatibility Test
3.01 CPU Board Compatibility Test PASS
Chapter 3 System Reliability Test
4.01 Power On/Off Test PASS
4.02 Warm Boot Stress Test PASS
4.03 ACPI Cycling Burn-in Test PASS
4.04 Full System, I/O Integrated Stress Test PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 5 of 27
Table of Contents
Revision History: ........................................................................................................................................................ 2
Test Results Definition: ............................................................................................................................................. 3
Test Results Summary: .............................................................................................................................................. 4
Table of Contents .......................................................................................................................................................... 5
Product Information: ................................................................................................................................................. 6
Platform Configuration: .............................................................................................................................................. 7
Test Programs: ......................................................................................................................................................... 10
Test Equipments: ..................................................................................................................................................... 11
Chapter 1:Function Test ......................................................................................................................................... 13
1.01 HDD Function Test ..................................................................................................................................... 13
1.02 SATA IDE Mode Function Test ................................................................................................................ 14
1.03 SATA AHCI Mode Function Test ............................................................................................................. 15
1.04 SATA RAID Mode Function Test ............................................................................................................. 17
Chapter 2:Software Compatibility Test ................................................................................................................. 18
2.01 OS and Driver Install Test ......................................................................................................................... 18
Chapter 3:Hardware Compatibility Test .............................................................................................................. 20
3.01 CPU Board Compatibility Test ................................................................................................................. 20
Chapter 4:System Reliability Test .......................................................................................................................... 21
4.01 Power On/Off Test ...................................................................................................................................... 21
4.02 Warm Boot Stress Test ............................................................................................................................... 22
4.03 ACPI Cycling Burn-in Test........................................................................................................................ 22
4.04 Full System, I/O Integrated Stress Test .................................................................................................... 23
Chapter 5:System Performance Test ..................................................................................................................... 25
5.01 HDD Performance Test .............................................................................................................................. 25
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 6 of 27
Product Information:
Item. Description.
Advantech Part Number 96HD4TB-ST-SG5KA
Manufacturer Seagate
Model Number ST4000VX000
From Factory 3.5”
Interface SATAIII
Capacity 4TB
Cache Capacity 64MB
Rotation Speed(RPM) 5900RPM
Host Transfer Rate 6GB
Bytes per Physical Sector 4096
Power On Hour(POH) 8760
Annualized Failure Rate (AFR)
/MTBF <1%
Voltage Tolerance +5.0V ± 5% and +12.0V ± 10%.
Operating Temperature 0°C to 70°C
Firmware CV12
Country of Origin Thailand
Dimension (W x H x D) 101.6mm x 26.11mm x146.99mm
RoHS Status (Yes/No) Yes
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 7 of 27
Platform Configuration:
PCE-7128
Item. Description.
M/B Name PCE-7128
PCB Version. A101-3
BIOS Version. 7128X006
Backplane Model. PCE-5B06-03
Backplane Verson. A101-2
CPU Model/Info Intel® Xeon® CPU E3-1275 v3 @3.5GHz
Memory Type/Info/Size DDR3 1600 4G*2 Apacer 78.B1GCE.AF1
PCH Chipset Intel C226 PCH
Graphic Controller Intel HD Graphic GT2
LAN1 Controller Intel® I217
LAN2 Controller Intel® I210
PCE-5127
Item. Description.
M/B Name PCE-5127
PCB Version. A101-3
BIOS Version. 5127X020
Backplane Model. PCE-5B06-03
Backplane Verson. A101-2
CPU Model/Info Intel® i7-3770 3.4GHz
Memory Type/Info/Size DDR3 1600 4G*2 Apacer 78.B1GCE.AF1
PCH Chipset Intel QM77 PCH
Graphic Controller Intel HD Graphic
LAN1 Controller Intel® 82579LM
LAN2 Controller Intel® 82583V
AIMB-581
Item. Description.
M/B Name AIMB-581
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 8 of 27
PCB Version. A101-3
BIOS Version. A581X057
CPU Model/Info Intel® i7-2600 3.4GHz
Memory Type/Info/Size DDR3 1600 4G*2 Apacer 78.B1GCE.AF1
PCH Chipset Intel QM67 PCH
Graphic Controller Intel HD Graphic
Audio Codec ALC892
LAN1 Controller Intel® 82579LM
LAN2 Controller Intel® 82583V
MIO-5271
Item. Description.
Project Name. MI0-5271
PCB Version. A101-3
BIOS Version. 5271X017
EC Version I2865X0101
CPU Model/Info Intel® Celenron® 2980U@ 1.60GHz
Memory Type/Info/Size DDR3L-1600 4GB Apacer 78.B2GCR.AF10C
PCH Chipset Lynx Point-LP PCH QM87
Graphic Controller GT3 Graphics, Generation 7.5 graphics core architecture
Audio Codec ALC888S
LAN1 Controller Intel i218
LAN2 Controller Intal i210
MIO-5290
Item. Description.
Project Name. MIO-5290
PCB Version. A101-2
BIOS Version. 5290X015.
EC Code Version. I1809X0100
CPU Model/Info Intel i3-3217UE @ 1.70GHz
Memory Type/Info DDR3 1333 2GB Apacer 78.A2GC9.4200C
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 9 of 27
Total Memory Size 8GB
PCH Chipset QM77
Graphic Controller VGA Function was supported intel PCH
Audio Codec ALC892
LAN1 Controller Intel® 82579LM
LAN2Controller Intel® 82583V
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 10 of 27
Test Programs:
Test Program Version
HD Tach V3.0.4.0
HD Tune Pro V5.5
CrystalDiskMake V3.0.3
ATTO Disk V2.46
PassMark Burn-In Test Pro V7.1 build 1017
PassMark Rebooter V1.3 build 1004
PassMark Sleeper V2.3 build 1009
Power on/off V3.3
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 11 of 27
Test Equipments:
Model Description
Power on/off test equipment (ATX/AT)
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 12 of 27
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 13 of 27
Chapter 1:Function Test
1.01 HDD Function Test
1.01.01.01 Test Purpose:
The purpose of SATA test is to analyze and validate the functional、performance capabilities、quality
and stability.
1.01.01.02 Test Standard:
Please refer to the Project Hardware and BIOS specification.
1.01.01.03 Test Tool:
1. SATA cable
2. SATA HDD
3. SATA DVD-ROM
1.01.01.04 Test Criteria:
1. The BIOS must detect SATA devices information.
2. The SATA function can install OS and work well on OS without hang, restart, or blue screen or
any problems.
3. The Device Management can not have any exclamation point and question mark.
4. Mark sure pass w/program without any error ocurrs.
1.01.01.05 Test Procedure:
1. Insert SATA HDD and DVD-ROM into the DUT
2. The BIOS detect SATA port HD correct information.
3. Install OS and all drivers.
4. SATA HDD can be copy/del/read/write file.
5. Install the PassMark BurnIn Pro program, and setting :
(a) Select tests to perform and their duty cycle: Select Disk(s) and Optical Drive(s)/ 100%
Loading/Auto Stop After : 30Minutes.
(b) Set test preferences: Select “Disk”-> Select Test this drive/ set File size: 15(% of disk), other
setting value keep defaults Preference.
(c) Then Press “Start selected tests” for test.
6. After finished testing, the test result will show on screen.
7. Change other port, and repeat 1~6.
1.01.01.06 Test Data:
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 14 of 27
Test Item Description Result Remark
Post information POST should show the correct model name PASS
BIOS information BIOS detect correct information PASS
Device Manager Device Management can not have any exclamation
point and question mark, and detect correct information PASS
Install OS &driver Can install OS and driver PASS
SATA Port Mark should all SATA port can detect and reboot
shutdown PASS
BurnIn Running passmark 30mins PASS
1.02 SATA IDE Mode Function Test
1.03.01.01 Test Purpose:
The purpose of this test is to ensure the functional of the SATA IDE Mode.
1.03.01.02 Test Standard:
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 15 of 27
Please refer to the Project Hardware and BIOS specification
1.03.01.03 Test Tools:
1. SATA HDD
2. SATA DVD-ROM
3. PassMark Burn In test Pro
1.03.01.04 Test Criteria:
1. The BIOS Setting IDE mode for DUT.
2. DUT must install OS and all drivers forIDE mode without any problems or error occurs.
1.03.01.05 Test Procedure:
1. Plug SATA HDD and DVD-ROM into DUT.
2. Setting IDE mode of SATA Mode on BIOS.
3. To install OS and drivers.
4. Install PassMark BurnIn Pro program and run 30min. After finished testing, the result will show
on screen.
5. Enter S1 mode, the system should be resume from S1 mode. This can work properly, and repeat
3times.
6. Enter S3 mode, the system should be resume from S3 mode. This can work properly, and repeat
3times.
7. Enter S4 mode, the system should be resume from S4 mode. This can work properly, and repeat
3times.
8. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can
work properly, and repeat 3times.
9. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times.
1.03.01.06 Test Data:
Test Item Description Result Remark
SATA IDE Mode
Win7 Ultimate SP1_X86 Installation Test. PASS
Win8.1 Pro_X86 Installation Test. PASS
ACPI S4 Mode PASS
OS shut dowm PASS
Warm Boot Test. PASS
1.03 SATA AHCI Mode Function Test
1.03.01.07 Test Purpose:
The purpose of this test is to ensure the functional of the SATA AHCI Mode.
1.03.01.08 Test Standard:
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 16 of 27
Please refer to the Project Hardware and BIOS specification
1.03.01.09 Test Tools:
4. SATA HDD
5. SATA DVD-ROM
6. PassMark Burn In test Pro
7. Intel F6 Install Floppy Driver or AHCI driver on USB flash disk.
1.03.01.10 Test Criteria:
3. The BIOS Setting AHCI mode for DUT.
4. DUT must install OS and all drivers for AHCI mode without any problems or error occurs.
1.03.01.11 Test Procedure:
10. Plug SATA HDD and DVD-ROM into DUT.
11. Setting AHCI mode of SATA Mode on BIOS.
12. To install OS and drivers, during install process, need to upload AHCI driver from Floppy or USB
flash disk.
13. Install PassMark BurnIn Pro program and run 30min. After finished testing, the result will show
on screen.
14. Enter S1 mode, the system should be resume from S1 mode. This can work properly, and repeat
3times.
15. Enter S3 mode, the system should be resume from S3 mode. This can work properly, and repeat
3times.
16. Enter S4 mode, the system should be resume from S4 mode. This can work properly, and repeat
3times.
17. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can
work properly, and repeat 3times.
18. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times.
19. Setting Enabled Hot Plug SATA Port on BIOS.
20. The DUT SATA should be Hot Plug and work properly, and repeat 3times.
1.03.01.12 Test Data:
Test Item Description Result Remark
SATA AHCI Mode
Win7 Ultimate SP1_X64 Installation Test. PASS
Win8.1 Pro_X64 Installation Test. PASS
ACPI S4 Mode PASS
OS shut dowm PASS
Warm Boot Test. PASS
Hot Plug PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 17 of 27
1.04 SATA RAID Mode Function Test
1.04.01.01 Test Purpose:
The purpose of this test is to ensure the functional of the SATA RAID Mode.
1.04.01.02 Test Standard:
Please refer to the Project Hardware and BIOS specification
1.04.01.03 Test Tools:
1. SATA HDD
2. SATA DVD-ROM
3. PassMark Burn In test Pro
4. Intel F6 Install Floppy Driver or RAID driver on USB flash disk.
1.04.01.04 Test Criteria:
1. The BIOS Setting RAID mode for DUT on BIOS.
2. DUT must install OS and all drivers for SATA mode without any problems or error occurs.
1.04.01.05 Test Procedure:
1. Setting RAID mode of SATA Mode on BIOS.
2. During boot, Press <Ctrl+I> to enter Intel Rapid Storage Technology - Option ROM and setting
RAID 0 Mode.
3. To install OS and driver, during install process need to upload RAID driver from Floppy or USB
flash disk should be has no hang, blue screen, or any problems.
4. To install PassMark Burn In test Pro and rn 30min. After finished testing, the result will show on
screen.
5. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can
work properly, and repeat 3times.
6. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times.
1.04.01.06 Test Data:
Test Item Description Result Remark
SATA RAID Mode
RAID0 PASS
RAID1 PASS
Rebuild PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 18 of 27
Chapter 2:Software Compatibility Test 2.01 OS and Driver Install Test
2.01.01.01 Test Purpose:
The purpose of this test is to ensure the OS compatibility of the DUT.
2.01.01.02 Test Standard:
Please refer to the Project Hardware and BIOS specification
2.01.01.03 Test Tools:
1. Microsoft OS installation DVD depends on X86/X64.
2.01.01.04 Test Criteria:
1. The OS X86/X64 installation process must complete without any error occurs.
2. The Server OS X86/X64 installation process must complete without any error occurs.
3. Device Management can not have any exclamation point and question mark.
2.01.01.05 Test Procedure:
1. Plug OS DVD or Server OS into DVD-ROM, and start install follow installation process.
2. After finish OS install, install all drivers for the DUT.
3. Make sure drivers of the DUT can install, and device management can not have any unknown
device.
2.01.01.06 Test Data:
Test Item Description Result Remake
Win7 Ultimate SP1 x86
OS Installation – English. PASS
Driver Installation. PASS
Device Management Check. PASS
Win7 Ultimate SP1 x64
OS Installation – English. PASS
Driver Installation. PASS
Device Management Check. PASS
Win8.1 Pro x86
OS Installation – English. PASS
Driver Installation. PASS
Device Management Check. PASS
Win8.1 Pro x64
OS Installation – English. PASS
Driver Installation. PASS
Device Management Check. PASS
Win Server_2008 R2 OS Installation – English. PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 19 of 27
Test Item Description Result Remake
SP1 Enterprise_x64 Driver Installation. PASS
Device Management Check. PASS
Win Server 2012
Standard_x64
OS Installation – English. PASS
Driver Installation. PASS
Device Management Check. PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 20 of 27
Chapter 3:Hardware Compatibility Test
3.01 CPU Board Compatibility Test
3.01.01.01 Test Purpose:
The purpose of this test is to validate and ensure the CPU Board compatibility of the DUT.
3.01.01.02 Test Standard:
Please refer to the Project Hardware specification and BIOS specification.
3.01.01.03 Test Tools:
1. Different Chipsets of CPU Board
3.01.01.04 Test Criteria:
1. With a different CPU board connected. The DUT must PASS without any error occurs.
2. BIOS must detect current information
3. Device Management can not have any exclamation point and question mark.
3.01.01.05 Test Procedure:
1. Connect to CPU board and power on.
2. The system should be detected HDD, then install OS and drivers for this.
3. Confirm the all kinds of CPU board should work properly.
3.01.01.06 Test Data:
Test Item Description Result Remark
CPU board BIOS version PCB Version OS install
MIO-5271 5271X018 A101-2 Win7/Win8.1/2012 PASS
MIO-5290 5290X015 A101-2 Win7/Win8.1 PASS
AIMB-581 A581X057 A101-3 Win7/Win8.1 PASS
PCE-5127 5127X030 A101-3 Win7/Win8.1/ Server2008R2 PASS
PCE-7128 7128X006 A101-3 Win7/Win8.1/Server2008R2/2012 PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 21 of 27
Chapter 4:System Reliability Test
4.01 Power On/Off Test
4.01.01.01 Test Purpose:
The purpose of this test is to examine and validate the stability of the Power On/Off and AT mode
under Widows OS.
4.01.01.02 Test Standard:
Please refer to the Project Hardware specification and BIOS specification
4.01.01.03 Test Tools:
1. Power on/off test equipment.
2. Power on/off Program
4.01.01.04 Test Criteria:
1. The test msut PASS the Power on / off circling test >= 100 times, booting rate=100%
2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any
problems.
3. The system must have no any error w/ Program.
4.01.01.05 Test Procedure:
1. Connect Power on/off test equipment to DUT for Power on/off test
2. Make sure PSON1 or HW Jumper set as ATX Mode.
3. Make sure BIOS item: After AC power Failure MUST set as "Always Off".
4. Install and execute Power on/off Program, and setting Timer :hr/min/sec on DUT.
5. Setup testing time, and change to zero of run number on Power on/off test equipment.
6. Start power on/off test and pass over100 times.
7. Make sure PSON1 or HW Jumper set as AT Mode
8. Repeat 4~5 and start power on/off test for AT mode and pass over 100 times.
4.01.01.06 Test Data:
Test Item Description Result Remark
Power On/Off test
(ATX mode)
1. 1. BIOS item: After AC power Failure set as "Always
Off"
2. 2. H/W jumper set as ATX mode
3. 3. Test at room temperature for 1000 duration cycles
3. Booting rate =100%
PASS
Power On/Off test
(AT mode)
1. BIOS item: After AC Power Failure set as "Always
Off".
2. H/W jumper set as AT mode
3. Test at room temperature for 1000 duration cycles
4. Booting rate =100%
PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 22 of 27
4.02 Warm Boot Stress Test
4.02.01.01 Test Purpose:
The purpose of this test is to analyze and validate the functional、performance capabilities、quality and
stability of DUT warm boot capability.
4.02.01.02 Test Standard:
Please refer to the Project Hardware specification and BIOS specification
4.02.01.03 Test Tools:
1. PassMark Rebooter
4.02.01.04 Test Criteria:
1. The test msut PASS the Reboot circling test >= 100 times, booting rate=100%
2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any
problems.
3. The system must have no any error w/ Program.
4.02.01.05 Test Procedure:
1. Install PassMark Rebooter program.
2. Executing program, and setting
(a) Maxiimum reboots 100 cycles.
(b) Delay Time Out setting before each reboot: 20~25 sec.
(c) Enabled Auto load Rebooter at startup.
3. Then start test Cycle.
4.02.01.06 Test Data:
Test Item Description Result Remark
Windows 7 Ultimate SP1
X64
1.Run PassMark Rebooter V1.3 Build1004
2. Must PASS for 100 duration cycles.
3.Time Out Before reboot:10-25secs
4. Booting rate =100%
PASS
4.03 ACPI Cycling Burn-in Test
4.03.01.01 Test Purpose:
The purpose of this test is to examine and validate the quality and stability of the DUT ACPI
capability.
4.03.01.02 Test Standard:
Please refer to the Project Hardware specification and BIOS specification
4.03.01.03 Test Tools:
1. PassMark Sleeper V2.3 Build1009
4.03.01.04 Test Criteria:
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 23 of 27
1. The ACPI function test msut PASS run 100 times
2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any
other problems.
4.03.01.05 Test Procedure:
1. Install PassMark Sleeper on the DUT.
2. Setup ACPI support mode.
3. Press Configuration-> Cycles Settings-> Cycle forever, then press ok.
4. Press Sleeper Now and start test 100 times.
4.03.01.06 Test Data:
Test Item Description Result Remark
Windows 7 Ultimate
SP1 X64
1. Run PassMark Sleeper V2.3 build 1009.
2. Select "all supported states". (S4)
3. Run for 100 times. The DUT MUST maintain a stable
condition after the test has been completed.
PASS
4.04 Full System, I/O Integrated Stress Test
4.04.01.01 Test Purpose:
The purpose of this test is to examine and validate the quality and stability all IO of the DUT.
4.04.01.02 Test Standard:
Please refer to the Project Hardware specification and BIOS specification
4.04.01.03 Test Tools:
1. PassMark BurnIn Pro
4.04.01.04 Test Criteria:
1. The Full loading test msut PASS run over 12hours
2. The DUT must maintain a stable condition without any system crash, hang, blue screen, restart or
any other problems.
3. The system must have no any error w/ PassMark BurnIn Pro Program.
4.04.01.05 Test Procedure:
1. Insert tool into all of IO port on DUT.
2. Install PassMark BurnIn Pro program.
3. Executing BurnIn test, and setting :
(a) Select tests toperform and their duty cycle: Setp Auto Stop “720” Minutes, select need to test
items
(b) Set test preferences: setup need to setting items.
(c) All setting finish, press “Start selected tests” for test.
4. The DUT run program over 12hours.
4.04.01.06 Test Data:
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 24 of 27
I/O Integrated Stress Test: Windows 7 Ultimate SP1 X64
Test Item Description Result Remark
CPU 100% Loading PASS
RAM 100% Loading PASS
VIDEO 100% Loading PASS
2D Graphics 100% Loading PASS
3D Graphics 100% Loading PASS
SATA1 SATA HDD Seagate ST4000VX000 File system:
NTFS PASS
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 25 of 27
Chapter 5:System Performance Test
5.01 HDD Performance Test
5.01.01.01 Test Purpose:
The purpose of this test is to ensure the HDD performance of the DUT.
5.01.01.02 Test Standard:
Please refer to the Project Hardware specification and BIOS specification.
5.01.01.03 Test Tools:
1. HD Tach
2. HD Tune Pro
3. CrystalDiskMark
4. AS SSD Benchmark
5. ATTO Disk Benchmark
5.01.01.04 Test Criteria:
1. Executing the BenchmarkTest test item of HD Tach
2. Executing the Benchmark\Read Test of HD Tune Pro.
3. Executing the BenchmarkTest default item of CrystalDiskMark
4. Executing the BenchmarkTest default item of AS AUTO Disk Benchmark
5.01.01.05 Test Procedure:
1. Install HD Tach program.
2. Executing program, then setting “Select Storage Device” and Long bench”
(a) Select Storage Device
(b) Long bench(32mb zones)
(c) Press Run Test.
1. Install and execute HD Tach, setting “Select Storage Device” and Long bench”:
(a) Select Storage Device
(b) Long bench(32mb zones)
2. Install and execute HD Tune Pro, setting “need to test HDD” and press “Start” for test.
3. Install and execute CrystalDiskMark, setting “need to test HDD” and press “All” start test.
4. Install and execute ATTO Disk Benchmark, setting Drive “need to test HDD” and press “Start”
for test.
5. Record all of test results.
5.01.01.06 Test Data:
HDD Performance (OS:)
Test Item HD Tach 3.0.4.0 MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 26 of 27
HDD Performance (OS:)
Test Item HD Tach 3.0.4.0 MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark
HDD
Long bench(32mb
zones)-Random access
/(smaller is better)
13.1 13.2 13 13 13
Long bench(32mb
zones)-CPU utilization /
(%,+/-2%) (smaller is better)
6 4 2 2 5
Long bench(32mb
zones)-Average read 169.5 170.1 169.6 169.1 168.9
Long bench(32mb
zones)-Burst Speed 3301. 310.6 336.9 349.3 373.2
HDD Performance (OS:)
Test Item HD Tune Pro 5.5 MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark
HDD
Burst Speed / (MB/s) 222.4 217 205.9 220.7 220.1
Transfer Rate - Min. (MB/s) 68.7 67 81.3 77.6 1.3
Transfer Rate - Max. (MB/s) 178.9 179 179 183.2 179.6
Transfer Rate - Average.
(MB/s) 139.1 137.8 139.8 139.6 128.1
Access Time (ms) 15.8 16.9 16 16 16.5
CPU Utilization (%) 6.2 3.9 1.1 2.1 7
HDD Performance (OS:)
Test Item Software Comment
/ (unit) MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark
HDD
Crystal
DiskM
ark
Read
(MB/s)
Seq 153.6 152.9 150.7 146.7 138.6
512K 30.23 32.88 31.76 30.43 28.75
4K 0.353 0.459 0.355 0.552 0.331
4K QD32 1.011 1.063 1.075 1.207 0.986
Write
(MB/s)
Seq 151.6 153.3 149 145.3 142.5
512K 71.54 76.21 74.83 84.06 70.29
4K 1.147 1.199 1.216 1.461 1.134
4K QD32 1.126 1.187 1.179 1.451 1.138
Drawings and specifications herein are property of Advantech and shall not be reproduced or copied or used without prior written permission.
Page 27 of 27
HDD Performance (OS:)
Test Item Software MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark
HDD
ATTO Disk
Benchmark
Read (MB/s) 160.739 164.937 160.499 150.441 151.309
Write (MB/s) 158.369 163.329 158.135 148.945 150.946