Using the correct lubrication before each swage operation is essential for mechanical splicing. Due to lubrication, the material in the swaging process flows much easier and helps form a tighter fit around the wire rope. See picture opposite: Sample 1; Dies have not been properly greased. Sample 2; Both upper and lower die have been coated with SPLICING GREASE. Our testing has shown a reduction of up to 20% less load when lubricants are used, leading to an enhanced die service life. It also helps avoid the splice sticking in dies after swaging, saving valuable time. - No jam - Less load - Longer service life For our environment: • Less energy to swage • Food processing safe The importance of lubrication TECHNICAL DATA SPLICING GREASE Art. No: 1 litre TALUGREASE 1L 5 litres TALUGREASE 5L 20 litres TALUGREASE 20L Information of ingredients Chemical name (CAS)/EG No. Conc. Paraffin oil, pharmaceutical (80424-70-5) 70-90 % Polybutene (900-29-6) 10-30 % Naphta (petroleum), hydrogenated light 265-149-8 (64742-47-8) 1<10 % TALURIT is a trademark owned by Talurit AB. All unauthorised use is prohibited. Splicing grease TALURIT™ TALURIT™ – Here with an efficient splicing lubricant Talurit AB · Amalia Jönssons gata 29 · 421 31 Västra Frölunda · Sweden · VAT SE556343720001 Phone +46 31 709 30 80 · Fax +46 31 47 10 71 · [email protected] · www.talurit.com TALURIT is a trademark owned by Talurit AB. All unauthorized use is prohibited. Rev. 2009-09-07 © 2014, Talurit AB

Splicing grease TALURIT™ · Splicing grease TALURIT™ TALURIT™ – Here with an efficient splicing lubricant. Talurit AB · Amalia Jönssons gata 29 · 421 31 Västra Frölunda

Download PDF Report

Upload
others
View
34
Download
0

Embed Size (px)

Citation preview

Page 1: Splicing grease TALURIT™ · Splicing grease TALURIT™ TALURIT™ – Here with an efficient splicing lubricant. Talurit AB · Amalia Jönssons gata 29 · 421 31 Västra Frölunda

Using the correct lubrication before each swage operation is essential for mechanical splicing. Due to lubrication, the material in the swaging process flows much easier and helps form a tighter fit around the wire rope. See picture opposite:Sample 1; Dies have not been properly greased.Sample 2; Both upper and lower die have been coated with SPLICING GREASE. Our testing has shown a reduction of up to 20% less load when lubricants are used, leading to an enhanced die service life. It also helps avoid the splice sticking in dies after swaging, saving valuable time.

- Nojam- Lessload- Longer servicelife

Forourenvironment:• Less energy to swage • Food processing safe

The importance of lubrication

TECHNICALDATA

SPLICINGGREASE Art. No: 1 litre TALUGREASE 1L 5 litres TALUGREASE 5L 20 litres TALUGREASE 20L

Information of ingredientsChemicalname (CAS)/EGNo. Conc.Paraffin oil, pharmaceutical (80424-70-5) 70-90 %Polybutene (900-29-6) 10-30 % Naphta (petroleum), hydrogenated light 265-149-8 (64742-47-8) 1<10 %

TALURIT is a trademark owned by Talurit AB. All unauthorised use is prohibited.

SplicinggreaseTALURIT™TALURIT™–Here with an efficient splicing lubricant

Talurit AB · Amalia Jönssons gata 29 · 421 31 Västra Frölunda · Sweden · VAT SE556343720001Phone +46 31 709 30 80 · Fax +46 31 47 10 71 · [email protected] · www.talurit.com