UOM 3.0 TR 4.0 TR 5.0 TR 7.5 TR 5.5 TR 5.5 TR DR 8.5 TR 11.0 TR 11.6 TR (HIGH CFM) 17.0 TR 17.0 TR (HIGH CFM)

40LC004R / 51MSC036DRHA 40LC005R / 51MSC048DRH 40LC006 / 38LH060DK 40LC009 / 38LH090TK 40LC006S / 38LH066S 40LC006SDR/ 38LH066S DR 40LC010C / 38LH100S 40LC012LH / 38LH066S,2nos. 40LC013HC / 38LH066S (2 Nos) 40LC018LN / 38LH100SS (2 Nos) 40LC018HC / 38LH100SS (2 Nos)

TR 3.0 4.0 5.0 7.5 5.5 5.5 8.5 11.0 11.6 17.0 17.0

BTU/HR 36000 48000 60000 90000 66000 66000 102000 132000 139200 204000 204000

Kcal/hr 9000 12000 15000 22500 16500 16500 25500 33000 34800 51000 51000

KwH/Hr 4.39 5.21 5.82 9.3 5.60 5.6 9.35 12.2 13.5 19.19 21.7

Volts/Hz/Ph 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3

mm 633 x 991 x 460 660 x 991 x 460 633 x 1163 x 460 700 x 1496 x 460 633 x 1163 x 460 750x1250x345 700 x 1646 x 460 900 x 1946 x 535 970 x 1946 x 684 970 x 1946 x 684 970 x 1946 x 684

kg 55.0 55.0 65.0 80.0 66.0 62.0 91.0 155.0 175.0 182.0 192.0

CASING MATERIAL

CASING THICKNESS mm

THERMAL INSULATION (Type / Thickness) mm

TYPE

FACE AREA sft 3.228 3.55 3.98 5.6 3.98 4.5 6.35 8.75 9.59 11.37 11.37

FACE VELOCITY m/sec 1.89 2.29 2.55 2.72 2.81 2.5 2.72 2.56 2.91 3.04 3.80

CMH 2040 2720 3400 5100 3740 3740 5780 7480 9350 11560 14450

CFM 1200 1600 2000 3000 2200 2200 3400 4400 5500 6800 8500

No OF ROWS Nos. 3 3 4 4 3 3 3 3 3 4 4

No OF CIRCUITS / COIL Nos. 4 2 4 9 8 8 12 14 16 24 24

FIN SPACING FPI 13 13 13 13 15 16 16 16 13 13 13

TUBE SIZE (OD / Thickness) Inches

TUBE (Material / Type)

FIN (Material / Thickness) mm

EXPANSION DEVICE Expansion Valve (BBI-4-CP100/TDEX6) ( Sporlan-BBIVE-5 ) Expansion Valve (SVE-8-VGA/TDEX8)Expansion Valve (BBI-4-CP100/TDEX6) Expansion Valve (BBI-4-CP100/TDEX6) Expansion Valve (SVE-8-VGA/TDEX8) Expansion Valve (SVE-8-VGA/TDEX8)

MAKE

TYPE

TYPE OF DISCHARGE Front / Top Front Front Front / Top Front Front / Top Front / Top Front / Top

No of impellers on same shaft 1 1 1 1 1 2 1 2 2 2 2

Total No of impeller 1 1 1 2 1 2 2 2 2 2 2

IMPELLER SIZE (Diameter / Width) Inches 11" x 12" 10-5/8" / 10-5/8" 11" x 12" 8"x10" 11" x 12" 10" x 10" 12" x 12" 12" x 12" 12" x 12"

AIR FLOW RATE CMH 2040 2720 3400 5100 3740 3740 5780 7480 9350 11560 14450

STATIC PRESSURE mm of WG 18.0 18.0 18.0 18.0 15.0 15.0 15.0 27.0 29.0 27.0 21.0

VELOCITY PRESSURE mm of WG 2.0 2.0 2.0 2.0 5.0 5.0 5.0 8.0 6.0 8.0 14.0

TOTAL PRESSURE mm of WG 20.0 20.0 20.0 20.0 20.0 20.0 20.0 35.0 35.0 35.0 35.0

OUTLET BLOWER VELOCITY m/sec 9.80 9.8 7.57 11.3 9.6 11.9 14.9

FAN SPEED RPM 920 920 920 920 930 1350.0 930 1030 900 860 873

RATED POWER CONSUMPTION KwH/Hr 0.4 0.4 0.45 0.8 0.45 0.5 0.8 1.4 1.7 1.7 3.24

DRIVE (Type) Belt Belt Belt Belt

MATERIAL OF CONSTRUCTION GI GI GI GI

CASING / IMPELLER GI GI GI GI

SOUND PRESSURE LEVEL dB(A) 68.0 68.0 72.0 75.0 72.0 71.0 75.0 82.0 85.0 86.0 88.0

FAN EFFICIENCY % - - - - - - - 60.0 60.0 59.0 51.0

BEARINGS (Type) - - - - - - - Ball bearing Ball bearing Ball bearing Ball bearing

BELTS (Size / Nos) - - - - - - - A-22 / 2 A-30 / 2 A-29 / 2 A-30 / 2

FAN PULLEY SIZE - - - - - - - 118.0 180.0 180.0 170.0

MOTOR PULLEY SIZE - - - - - - - 90.0 106.0 106.0 106.0

FAN MOTOR (Make) PSC / M/s GE/CG/PICL PSC / M/s GE/CG/PICL PSC / M/s GE/CG/PICL ABB/CG/HM/BBL/Weiling ABB/CG/HM/BBL/Weiling ABB/CG/HM/BBL/Weiling ABB/CG/HM/BBL/Weiling

FAN MOTOR (Type / Qty) Single phase / Two Single phase / one Single phase / one Single phase / Two 3-Phase / one 3-Phase / one 3-Phase / one 3-Phase / one

FAN MOTOR (Rating / Speed) KW / RPM 0.370 / 930 0.370 / 930 0.370 / 930 0.370 / 930 0.370 / 930 0.560/1350 0.370 / 930 1.5 / 1405 2.2 / 1425 2.2 / 1425 3.7 / 1430

INSULATION CLASS Class B Class B Class B Class B Class B Class B Class B Class F Class F Class F Class F

RATED POWER CONSUM. / EVAPORATOR KwH/Hr 0.4 0.4 0.45 0.8 0.45 0.49 0.8 1.4 1.7 1.7 3.24

RATED POWER SUPPLY VoltS/Hz/Ph

QUANTITY Nos. 1 1 1 1 1 1 1 3 3 3 3

MEDIA

EFFICIENCY / SIZE

CASING MATERIAL Aluminium G.I. Aluminium Aluminium Aluminium G.I Aluminium GI GI GI GI

OVERALL SIZE mm 885 x 400 x 12 885 x 400 x 40 1062 x 400 x 12 1398 x 400 x 12 1062 x 400 x 12mm 1160x285x10 1548 x 400 x 12 1710 x 447 x 50 1711 x 593 x 50 1711 x 593 x 50 1711 x 593 x 50

FACE AREA sft 3.81 3.81 4.57 6.02 4.57 3.55 6.67 8.22 10.92 10.92 10.92

M/S CARRIER AIRCONDITIONING & REFRIGERATION LIMITED ; GURGAON (INDIA)

DUCTED AIR-CONDITIONERS : TECHNICAL SPECIFICATION

PARAMETER

MODEL No (INDDOR / OUTDOOR)

NOMINAL REFRIGERATION CAPACITY

RATED POWER CONSUMPTION

RATED POWER SUPPLY

INDOOR UNIT

OVERALL SIZE (Width x Length x Height)

NET WEIGHT

CASIN

G Powder Coated galvanised sheet duly phosphated for increased corrosion resistance.

1.0/1.2

Polyethylene (6.0 / 12.0 mm Thick)

EVAPORATOR

Air-cooled

AIR FLOW RATE

3/8" / .013"

Copper / Plain Copper / Internally Grooved

Aluminium / 0.11 mm

Copper Capillary Tube

EVAPORATOR F

AN

PART FROM SOME REPUTED MANUFACTURER FOR SUITABLE CAPACITY DECIDED BY APPLICABLE DESIGN SOFTWARE

Double inlet double width

Front

10-5/8" / 10-5/8"

AIR

MOVIN

G U

NIT

ASSEM

BLY

Direct

Aluminium

GI / Aluminium

PSC / M/s GE/CG/PICL

Single phase / One

ELECT

230 / 50 / 1 400 / 50 / 3

FIL

TER

Non Wooven Synthetic Fibre

90% & 10 microns

mm 435 x 1030 x 694 435 x 1030 x 694 660 x 1200 x 850 660 x 1200 x 850 600 x 1250 x 845 410x1040x875 714 x 982 x 1082 600 x 1250 x 845 600 x 1250 x 845 714 x 982 x 1082 714 x 982 x 1082

Kg 70 78 160 200 150 112 225 150 150 225 225

CASING MATERIAL

CASING THICKNESS mm

TYPE

COMPRESSOR TYPE Type Rotary Recip / Rotary Recip Recip Scroll Scroll Scroll Scroll Scroll Scroll Scroll

MAKE GMCC Copeland / GMCC Copeland Copeland Copeland Copeland Manuerop Copeland Copeland Manuerop Manuerop

MODEL PH340X3C-4KUS1 CR30K6M-PF1 / PH400X3CS-4KTS1 CR36K6-TF6-101 CR36K6-TF6-101 ZR72KC-TFD ZR72KC-TFD SM110-S4V ZR72KC-TFD ZR72KC-TFD SM110-S4V SM110-S4V

REFRIGERANT R-22 R-22 R-22 R-22 R-22 R-22 R-22

No OF CIRCUIT / UNIT 2 2 2 3 1 1 1 1 1 1 1

No OF COMPRESSORS / UNIT 2 2 2 3 1 1 1 2 2 2 2

RATED POWER SUPPLY VoltS/Hz/Ph 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3

TYPE

FACE AREA sft 8.24 8.24 14.85 16.17 14.85 11.15 12.912 14.85 14.85 12.912 12.912

FACE VELOCITY m/sec 1.85 1.85 1.43 1.39 1.43 1.94 2.36 1.43 1.43 2.36 2.36

CMH 5100 5100 7100 7500 7100 7225 10200 7100 7100 10200 10200

CFM 3000 3000 4176 4412 4176 4250 6000 4176 4176 6000 6000

Nos OF ROWS Nos. 2 2 3 2 2 2 2 2 2 2 2

Nos OF CIRCUIT / COIL Nos. 2 2 3 5 8 4 5 8 8 5 5

FIN SPACING FPI 17 17 17 17 17 18 17 17 17 17 17

TUBE SIZE (OD / Thickness) inches 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013" 3/8" & 0.013"

TUBE (Material / Type) Plain Plain Plain Plain Plain Plain Internally Grooved Plain Plain Internally Grooved Internally Grooved

FIN (Material / Thickness) Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm Aluminium & 0.11mm

FAN (Type / Make)

FAN (Size & Qty/Condenser) mm / nos. 457mm/01 457mm/01 482.6mm/02 482.6mm/02 482.6 / 02 609.6/1 609.6 / 01 482.6 / 02 482.6 / 02 609.6 / 01 609.6 / 01

SOUND PRESSURE LEVEL dB(A) 72 72 75 75 75 75 75 75 75 75 75

RATED POWER SUPPLY VoltS/Hz/Ph 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 400 +/-10% / 50 / 3 230 +/-10% / 50 / 1 230 +/-10% / 50 / 1 400 +/-10% / 50 / 3 400 +/-10% / 50 / 3

FAN MOTOR (Rating / Speed) KW / RPM .15/920 .15/920 .15/920 .15/920 0.15 / 920 .37/930 0.375 / 920 0.15 / 920 0.15 / 920 0.375 / 920 0.375 / 920

RATED POWER CONSUMPTION / CONDENSER KwH/Hr 0.32 0.32 0.5 0.5 0.5 0.37 0.4 0.5 0.5 0.4 0.4

Inches 1/4" 1/4" 3/8" 3/8" 1/2" 1/2" 5/8" 1/2" 1/2" 5/8" 5/8"

Inches 1/2" 5/8" 5/8" 5/8" 1-1/8" 7/8" 1-1/8" 1-1/8" 1-1/8" 1-1/8" 1-1/8"

OUTDOOR UNIT

OVERALL SIZE (Width x Length x height)

NET WEIGHT

CASIN

G GI GI

1.0/1.2 1.0/1.2mm

FLOOR MOUNTED Floor

COM

PRESSOR

CONDENSER

AIR COOLED

AIR FLOW RATE

R-22

LIQUID LINE

SUCTION LINE

AIR

MOVIN

G

UNIT

Centrifugal & M/s Rishab coil

ELECT

INTER CONNECTING TUBES