53

1

9

4

8

6

2

7

10

NOTE: #10 .5" X 13" PRECISION DRILL ROD

SCALE: 1:10

ITEM # PART NAME QTY DWG #

1 SHAFT ASSEMBLY 1 1C-00

2 TTTF BASE ASSEMBLY 1 2-00

3 CROSS MEMBER ASSEMBLY 1 3-00

4 WORM SHAFT ASSEMBLY 1 4-00

5 DISPLAY ASSEMBLY 1 5-00

6 LOAD AND MOUNT ASSEMBLY 1 6-00

7 TRANSMISSION ASSEMBLY 1 7-00

8 TTTF RIGHT UPRIGHT 1 1A-00

9 TTTF LEFT UPRIGHT 1 1B-00

10 LINEAR SHAFT 2 N/A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 1 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 0-00 Scale: 1:5CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: Final Assembly

SPENCER OLDEMEYER 5/7/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:

THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

FINAL ASSEMBLY

QTY:1

21

4

3

ITEM NO. PART # DESCRIPTION QTY.

1 1-61 UPRIGHT2 12 1-62 QUICK RELEASE LOCK 13 1-52 UPRIGHT BARRELNUT 44 N/A R8 BEARING 2

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 2 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1A-00 Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: TTTF Upright2 Assembly

CARLOS DUARTE 5/1/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TTTF RIGHT UPRIGHT ASSEMBLY

QTY: 1

12

ITEM NO. PART # DESCRIPTION QTY.

1 1-51 UPRIGHT1 12 1-52 UPRIGHT BARRELNUT 4

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 3 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1B-00 Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: TTTF Upright1 Assembly

CARLOS DUARTE 4/29/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TTTF LEFT UPRIGHT ASSEMBLY

QTY: 1

12

3

NOTE:#1 IS A THRUST BALL BEARING .5" ID x 1.1875" OD#2 IS A BRONZE WORM GEAR 12 PITCH, 30 TEETH, .5" BORE (MSC #04169470) BROACH 1/8" KEYWAY AND DRILL FOR SET SCREW

ITEM NO. PART # DESCRIPTION QTY.

1 N/A THRUST BEARING 42 N/A WORM GEAR 23 1-21 BALL SCREWS 2

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 4 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1C-00 Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: Shaft Assembly

CARLOS DUARTE 5/4/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

QTY: 1

SHAFT ASSEMBLY

0.499

14.538

13.288

12.600

0.600

14.900

0.125

A A

0.065

SECTION A-A

NOTE: TURN ENDS OF BALL SCREW TO 0.50 AND MILL1/8 KEYWAY(McMASTER-CARR #5966K26)

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 5 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1-21Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 1-21

4/29/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESSTEEL ALLOYMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BALL SCREWS

QTY:2CARLOS DUARTE

0.6250.9001.2002.000

10.000

10.80011.100

12.000

4 X 0.313

4 X R2.8004 X R0.300

4 X 0.625

0.40

00.

700

0.90

01.

400

1.90

02.

100

2.40

02.

800

A A

0.27

5

0.90

0

1.90

0

2.52

5

0.375

0.750

4 X 0.3125 1.000

4 X 0.313 0.375

R0.125

0.20

00.

200 SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 6 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1-51Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 1-51

SPENCER OLDEMEYER 4/16/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPRIGHT1

QTY:1

0.750

TAP 5/16-18 THRU

0.630

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 7 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1-52Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 1-52

4/29/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPRIGHT BARRELNUT

QTY:8CARLOS DUARTE

0.90

01.

400

1.90

0

2.60

0

0.6252.0003.0785.141

10.00011.375

4 X 0.625 2 X 1.120 2 X 0.313

0.40

0

0.70

0

1.50

02.

100

2.80

0 1.20010.800R2.800

R2.800

R0.500

R1.100R0.500 R0.500

R2.800

0.900R1.100

A A

0.27

5

0.90

0

1.90

0

2.52

5

0.375

2 X 0.313 0.375

2 X 0.3125 1.000

3.70

0

12.000

0.75

0

0.20

00.

550

R0.125

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 8 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1-61Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 1-61

SPENCER OLDEMEYER 4/16/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPRIGHT2

QTY:1

0.962

0.650

0.2000.304

0.554 0.517

0.374

0.501

1.100

1.500

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 9 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 1-62Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 1-62

4/29/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESBRASSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

QUICK RELEASE LOCK

QTY:1CARLOS DUARTE

32

1

4

5

6

NOTE:#5 McMASTER ITEM #8339T5#6 McMASTER ITEM #7343K184

ITEM NO. PART # DESCRIPTION QTY.1 2-03 COVER 12 2-04 BASEWALL 13 2-01 BASE 14 2-02 BASEWALL PANEL 1

5 N/A DIGITAL PANEL VOLTMETER 1

6 N/A TOGGLE SWITCH 1

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 10 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 2-00 Scale: 1:4CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: TTTF Base AssemblyCARLOS DUARTE 5/7/2009

DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

QTY: 1

TTTF BASE ASSEMBLY

11.7511.089.908.006.004.00

2.100.93

0.51

2x 0.501 0.500

4x 0.3125 0.500 1.216 0.3752x 0.626 THRU ALL

0.625 THRU ALL

4.626

5x R0.375

2.00

02.

625

3.25

0

4.25

04.

875

5.50

07.

000

3.75

0

A A

SCALE 1:5

1.00

0.12

5

0.70

8x R0.10

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 11 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 2-01 (1 OF 3)Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 2-01

CARLOS DUARTE 4/27/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BASE

QTY:1

0.24

0.44

8

0.57

8

3.92

7.63

8.91

3

9.49

1.98

12.00

14.00

0.578

13.422

2x R1.375

10x R0.375

4x R2.00

A

A

SCALE 1:5

0.400

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 12 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 2-01 (2 OF 3)Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 2-01CARLOS DUARTE 4/27/2009

DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BASE

QTY:1

1.250

4x 0.257 0.4005/16-18

17/16 0.31254x 5/16 THRU ALL

0.125

1.25

08.

240

12.750

1.000

SCALE 1:5

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 13 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 2-01 (3 OF 3)Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 2-01CARLOS DUARTE 4/27/2009

DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BASE

QTY:1

0.0630.25 3.000

0.1252.875

0.75

0

1.63

01.

133

1.89

3

1.8204.5005.0005.500

0.500

6.5006.250

0.2502.

125

0.88

4x 0.164 THRU ALL1.

500

0.64

1.253.25

0.400 0.1250.25 THRU ALL

0.450 0.1250.313 THRU ALL

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 14 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 2-02Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 2-02

CARLOS DUARTE 5/4/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BASEWALL PANEL

QTY:1

14.000

0.75

0R0.1875

9.50

08.

875

7.75

1.75

0

0.62

5

4x R2.000

0.2500.6251.2501.750

12.250

14.000

12x R0.375

4x 1732 " 0.31254x 0.33 THRU ALL

8.25

1.25

0

12.750

A

A

0.50

0.0625

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 15 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 2-03Scale: 1:5CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 2-03

CARLOS DUARTE 4/22/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

COVER

QTY:1

3.00

0

13.5000

9.00

0

0.1875

3.9375

9.5625

4x R1.750

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 16 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 2-04Scale: 1:5CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 2-04CARLOS DUARTE 4/29/2009

DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BASEWALL

QTY:1

14

2

3

NOTE:#3 CLOSED FRELON LINED BEARING

.5" ID X .875" OD X 1.25"6061 - T6 ANODIZED ALUMINUM(MCMASTER CARR #5986K83)

#4 SNAP RETAINING RING TO FIT #3

ITEM NO. PART # DESCRIPTION QTY.

1 3-01 FLANGED BALL NUT 22 3-02 CROSS 13 N/A LINEAR BUSHING 24 N/A RETAINING RING 4

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 17 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 3-00Scale: 1:1.5CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 3-00

5/7/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

CROSS MEMBER ASSEMBLY

QTY: 1SPENCER OLDEMEYER

2.0001.000

R0.125

R0.250

R0.250

1.00

0

2.00

0

0.200

NOTE: MODIFICATIONS TO PURCHASED FLANGE (MCMASTER #5966K46)

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 18 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 3-01Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 3-01

5/6/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

FLANGED BALL NUT

QTY:2SPENCER OLDEMEYER

9.200

R0.123

R0.123 2.800

0.7001.3901.850

2.6003.3504.600

5.8506.600

7.3507.810

8.500

9.200

0.65

0

1.40

0

2.15

0

2.80

0

2 x 1.570

0.199 .98 x 1/4-20

0.625

2 X 0.878

2 X R0.700

4 X R0.800

4 X R1.000

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 19 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 3-02Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 3-02

5/1/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

CROSS

QTY:1SPENCER OLDEMEYER

2 8 6 7 5 4

13

SCALE: 1:5

ITEM NO. PART # DESCRIPTION QTY.

1 4-01 BOTTOM HOUSING 1

2 4-02 TOP HOUSING 13 4-03 WORM GEAR SHAFT 1

4 N/A TOOTH SPROCKET 1

5 N/A WORM 2

6 N/A BRONZE BUSHING 5

7 4-07 MODIFIED SHAFT COLLAR 4

8 N/A PIN 1

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 20 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 4-00 Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: Worm Shaft Assembly

JUSTIN RUEGSEGGER 5/4/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

WORM SHAFT ASSEMBLY

QTY: 1

1.52

5

2.15

0

3.15

0

3.77

5

4.15

0

4.40

0

0.31

3

1.73

0

2.65

03.

680

3.90

0

2 X 2.000

0.20

01.

607

0.52

9

0.5001.875

3.572

4.872

6.272

7.572

9.270

11.145

10.645

5 X R0.250

R0.250R0.150

4X 0.314 THRU

4X 0.328 THRU0.531 0.34

#10-24 UNC .7511 x 0.150 0.800

8.898

5.572

1.0002.1452.572

8 X R 0.125 6.572

A

SCALE 1:5

R0.500

R1.220

DETAIL A SCALE 1 : 1

TOP VIEW

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 21 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 4-01 (1 OF 2)Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 4-01 Bottom Housing

5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BOTTOM HOUSING

QTY:1JUSTIN RUEGSEGGER

SCALE: 1:52x 0.690 THRU

2X 1.120 0.050

A

A

BACK VIEW

R 0.375

0.52

9

2x 2.890 0.300

2x 1.575 0.875

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 22 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 4-01 (2 OF 2)Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 4-01 Bottom Housing

5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

BOTTOM HOUSING

QTY:1JUSTIN RUEGSEGGER

1.60

7

0.20

0R0.125

8.572

6.572

4.572

2.572

2 x R1.445 0.300

2 x 1.505 0.575

A

A0.650

R0.375

0.90

4

SECTION A-A

SCALE: 1.5

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 23 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 4-02 (1 OF 2)Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 4-02 Top Housing

5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TOP HOUSING

QTY:1JUSTIN RUEGSEGGER

0.31

31.

520

1.73

02.

150

2.65

03.

150

3.68

03.

775

4.15

04.

400

0.5001.875

3.5734.8725.5726.2727.573

9.270

8.750

2.247

8.898

10.64511.145

1.000

2.145

R0.150

R0.250

1.1451.520

4x 0.314 THRU

2x 1.120 0.050

2x 0.690 THRU

0.531 0.3404X 0.328 THRU

0.375 0.2208X 0.206 THRU

3X 0.206 THRU

B

R1.220

R0.500

DETAIL B SCALE 1 : 1 SCALE: 1:5

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 24 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 4-02 (1 OF 2)Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 4-02 Top Housing

5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TOP HOUSING

QTY:1JUSTIN RUEGSEGGER

0.500

0.3130.500

1.375

2.500

5.375

6.500

9.800

10.500

SCALE: 1:5

0.125

0.188

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 25 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 4-03Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 4-03 Wormshaft

5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

WORM GEAR SHAFT

QTY:1JUSTIN RUEGSEGGER

0.3125

NOTE: MODIFICATION TO MSC PURCHASED PART (MSC#: 35463652)

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 26 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 4-07Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 4-07 Modified Shaft Collar

5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESSTEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

MODIFIED SHAFT COLLAR

QTY:4JUSTIN RUEGSEGGER

38

5

14

7

2

6

NOTE:#5 HANDBAR IS 1" X 9.375" BAR, KNURLED FOR TEXTURE

ITEM NO. PART # DESCRIPTION QTY.

1 5-01 HOUSING BACKING 12 5-02 DISPLAY HOUSING 1

3 5-03 DISPLAY ASSEMBLY - LEFT UPRIGHT 1

4 5-04 DISPLAY ASSEMBLY - RIGHT UPRIGHT 1

5 N/A HANDBAR 16 N/A LED FACE 27 N/A DISPLAY PIVOT 2

8 5-08 TTTF TOP PLATE 1

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 27 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 5-00 Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 5-00

SPENCER OLDEMEYER 5/4/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

DISPLAY ASSEMBLY

QTY: 1

8.250

2.40

02.0004 X R0.325

2 X R0.100

2 X 0.1500.175

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 28 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 5-01Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 5-01

5/1/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESCLEAR CAST ACRYLICMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

HOUSING BACKING

QTY:1SPENCER OLDEMEYER

R0.450

R0.325

R0.200

0.125

0.250

0.500

3.8754.125

4.3754.6258.000

4.250

R0.12010-24 UNC 0.3802 x 0.150 0.510

8.500

1.25

0

1.13

0

R0.120

2.65

0

0.75

5

0.500

1/4-20 UNC THRU2 x 0.201 THRU

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 29 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 5-02Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 5-02

5/1/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

DISPLAY HOUSING

QTY:1SPENCER OLDEMEYER

110

R1.480

R0.260

R0.330

R0.260

R0.260

R0.500

R1.418

0.500

0.500

0.500

R0.750

R0.188.25 THRU.375 .375

1.020

A

A

0.50

0

0.5003.4003.650

0.25

0

R0.070

0.500

0.9002.2232.750

0.750

0.95

0

2.32

5

3.55

5

0.87

5

2 X 0.3135

0.250

0.200

0.300

0.500

4.30

5

0.375

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 30 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 5-03Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 5-03

5/1/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

DISPLAY ASSEMBLY - LEFT UPRIGHT

QTY:1SPENCER OLDEMEYER

R0.260

R0.500

R1.418

R0.260 R0.260

0.500

R0.260

R1.480

R0.7500.500

110

0.50

0A

A

0.50

0

0.5003.400

3.650

3.55

5

2.32

5

0.95

0

0.9000.750

2.750

0.87

5

1.020

0.250

0.375 .375.25 THRU

2.223

0.375

4.30

5

0.2000.300

0.500

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 31 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 5-04Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 5-04

5/1/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

DISPLAY ASSEMBLY - RIGHT UPRIGHT

QTY:2SPENCER OLDEMEYER

R1.220

R0.250

R0.500

B

B

AA 4.395

0.200

SECTION B-B

11.146

0.18

8

0.50

0

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 32 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 5-08 (1 OF 2)Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 5-08

SPENCER OLDEMEYER 5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TTTF TOP PLATE

QTY: 1

3.573

7.573

1.010

0.50

0

3.40

0

2 X 0.251

0.500

4.873

6.273

10.64610.136

5.573

2.15

03.

150

0.31

3

2 X 0.375

0.500 0.3304 x 0.328 THRU ALL

1.125 0.3132 x 0.880 THRU ALL

C

R0.251

R0.971

R0.500

R0.250

R0.250

2.000

2.50

0

5

R0.094

0.57

5

0.97

0

1.39

0

2.25

0 0.4791.500

5.0006.573

DETAIL C SCALE 1 : 1.5

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 33 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 5-08 (2 OF 2)Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 5-08

SPENCER OLDEMEYER 5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TTTF TOP PLATE

QTY: 1

53

7

4

2

1

6NOTE:#6 IS A GRADE 8 BOLT 5/8-18 x 3"#7 IS A STANDARD TENSILE SPECIMEN

SCALE 1:5

ITEM NO. PART # DESCRIPTION QTY.1 6-01 LOADCELL 12 6-02 LOADCELL ATTACHMENT PLATE 13 6-04 LOAD SPREADING NUT 24 6-05 SPECIMEN GRIP 25 6-03 LOAD SPREADING WASHER 26 N/A GRADE 8 BOLT 27 N/A TENSILE SPECIMEN 2

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 34 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 6-00 Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: TTTF Loadcell and Mounting Assembly

CARLOS DUARTE 5/5/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

QTY: 1

LOAD AND MOUNTING ASSEMBLY

0.627

0.500

1.375

0.563

A

A

10x 0.15

2x 0.25

3.3002.500

2.90

36

4x R 0.0625

0.200

SECTION A-A

5/8-18 THREADS

2x 45 0.0625

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 35 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 6-01Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 6-01ACARLOS DUARTE 4/26/2009

DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES4150 STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOADCELL

QTY:1

3.300

0.627

2x 0.250PRESS FIT ALIGNMENT PINS

10x TAP TO 10-32 0.159

2.90036

A A

SCALE 1:2

0.625

SECTION A-A45 x 0.0625

TAP TO 5/8-18 THRU ALL

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 36 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 6-02Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 6-02

CARLOS DUARTE 4/15/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES4140 STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOADCELL ATTACHMENT PLATE

QTY:1

0.625

1.00

1.50

A A

0.375

30

SECTION A-A

45 x 0.03

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 37 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 6-03Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 6-03

CARLOS DUARTE 4/15/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES4140 STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOAD SPREADING WASHER

QTY:2

5/8-18 THRU ALL 0.58 THRU ALL

1.00

1.50

0.625

A A

0.125

0.375

30

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 38 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 6-04Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 6-04CARLOS DUARTE 4/15/2009

DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES4140 STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOAD SPREADING NUT

QTY:2

1.000.260.40

A A

1.62

5

1.40

0

1.37

5

1.07

5

R0.034x R0.125

SECTION A-A

5/8-18 UNC 1.00

2x 45 x 0.025

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 39 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 6-05Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 6-05

CARLOS DUARTE 4/29/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES4140 STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

SPECIMEN GRIP

QTY:2

21122 2

1312

20

109

17

826

7

46

5

27

24

1518

3

16

19

28

14

11

25

23

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 40 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-00 (1 OF 2)Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7

5/4/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TRANSIMISSION ASSEMBLY

QTY:1AMANDA BOLLAND

ITEM NO. PART # DESCRIPTION QTY.

1 7-01 CHAIN HOUSE 12 7-02 CHAIN HOUSE SPACER 13 7-03 CHAIN COVER 14 7-04 WHEEL 15 7-05 QUICK PIN 16 7-06 CRANK HANDLE SUPPORT 17 7-07 LOWER SLIDE SPACER 18 7-08 LOWER GEAR 100 19 7-09 LOWER MIDDLE SPACER 110 7-10 LOWER GEAR 32 1

11 N/A EIGHTH X THREEQUARTER DOWEL PIN 2

12 7-12 LOWER SHAFT KEY 113 7-13 LOWER SHAFT SLEEVE 114 7-14 SHAFT END CAP 215 7-15 UPPER SPACER 1 116 7-16 UPPER GEAR 32 117 7-17 UPPER SPACER 2 118 7-18 UPPER SHAFT 119 7-19 UPPER GEAR 100 120 7-20 UPPER SPACER 3 121 7-21 UPPER SPROCKET 122 7-22 UPPER SPACER 4 123 N/A EIGHTH X ONE DOWEL PIN 224 N/A HANDLE 125 N/A R8 BEARING 226 N/A 4-40 X HALF SCREW 227 N/A 10-32 X HALF SCREW 228 N/A CHAIN SIZE #25 1

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 41 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-00 (2 OF 2)Scale: 1:3CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7

5/4/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESVARIOUSMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

TRANSIMISSION ASSEMBLY

QTY:1AMANDA BOLLAND

R2.0000

R1.8125

2 X 0.251 .75

.75 0.2012 X TAP TO 1/4-20

2 X 0.2062 X 0.251

3 X 1.1261.5625

3.46

3

3.83

8

4 X R0.25

2 X R0.5625

A A

0.125

0.875

2.00

0

4.88

0

10.1

51

R0.125

0.5625

0.63

12

1.03

125

1.43

12

2.06

25

6.15

05

0.550

1.07

5R0.125

1.20

0

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 42 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-01Scale: 1:4CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-01

4/30/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

CHAIN HOUSE

QTY:1AMANDA BOLLAND

2.0625

R0.875

1.125

2 X 0.206 2 X 0.251

0.12

5

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 43 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-02Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-02

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

CHAIN HOUSE SPACER

QTY:1AMANDA BOLLAND

R2.000

R1.000

2.00

0

2.31

3

2.68

8

4.08

8

6.15

1

2 X 0.251

2 X 0.251

2 X 1.124

A

A

R0.100

0.250

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 44 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-03Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-03

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

CHAIN COVER

QTY:1AMANDA BOLLAND

1.000

2.000

7.100

7.750

5 X 0.2501.40 BC

R0.550TAP TO 3/8-16

3.000

R0.650

R0.700

R2.600

R2.800

R3.500

R0.625

0.541

1.66

4

14 X R0.250

3.250

1.48

2

A A

0.37

5

0.18

8

R0.125

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 45 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-04Scale: 1:2CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-04

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

WHEEL

QTY:1AMANDA BOLLAND

4 X 0.2504 X 0.1100.820 BC

0.12

50

1.700 R0.0625

NOTE: PART FROM MSC # 60010501

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 46 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-05Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-05

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

QUICK PIN

QTY:1AMANDA BOLLAND

0.3723

0.565

2.000

5 X 0.185 1.40 BCTap 1/4-28

4 X 0.0890 0.82 BCTAP 4-40 0.30

A

A

0.375

0.620

0.90

0 0.345

SECTION A-A

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 47 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-06Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-06

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

CRANK HANDLE SUPPORT

QTY:1AMANDA BOLLAND

0.374

0.5505

0.642

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 48 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-07Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-07

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOWER SLIDE SPACER

QTY:1AMANDA BOLLAND

2 X 0.112@ 180 0.70 BC

2 X 0.126@ 180 0.70 BC

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 49 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-08Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-08

AMANDA BOLLAND 4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESSTAINLESS STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOWER GEAR 100

QTY:1

0.500

0.374

0.900

2 X 0.112 @ 180 0.70 BC

2 X 0.126@ 180 0.70 BC

0.1250.18750.3125

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 50 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-09Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-09

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOWER MIDDLE SPACER

QTY:1AMANDA BOLLAND

2 X 0.126@ 180 0.70 BC

2 X 0.112@ 180 0.70 BC

NOTE: PART FROM W. M. BERG #F32S3-32

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 51 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-10Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-10

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESSTAINLESS STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOWER GEAR 32

QTY:1AMANDA BOLLAND

0.57

50.

125

0.125

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 52 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-12Scale: 5:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-12

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOWER SHAFT KEY

QTY:1AMANDA BOLLAND

0.900

0.112 @ 180 0.70 BC2 X TAP TO 4-40 0.3

2 X 0.126@ 180 0.70 BC

0.125

0.374

0.25

00.

250

0.50

0

0.164 TAP TO 8-32

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 53 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-13Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-13

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

LOWER SHAFT SLEEVE

QTY:1AMANDA BOLLAND

0.188

0.525

0.625

0.050

0.100

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 54 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-14Scale: 4:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-14

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

SHAFT END CAP

QTY:2JUSTIN RUEGSEGGER

0.500

0.625

0.045

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 55 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-15Scale: 4:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-15

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER SPACER 1

QTY:1JUSTIN RUEGSEGGER

2 X 0.1260.70 BC

NOTE: PART FROM W.M. Berg #F32S3-32

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 56 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-16Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-16

JUSTIN RUEGSEGGER 4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESSTAINLESS STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER GEAR 32

QTY:1

0.900

0.5002 X 0.126

0.70 BC

0.315

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 57 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7/17Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-17

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER SPACER 2

QTY:1JUSTIN RUEGSEGGER

0.500

0.1590TAP 10-32 0.5

2.37

5

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 58 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-18Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-18

4/27/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER SHAFT

QTY:1JUSTIN RUEGSEGGER

2 X 0.1260.70 BC

NOTE: PART FROM W. M.BERG #F32S3-100

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 59 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-19Scale: 1:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-19

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESSTAINLESS STEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER GEAR 100

QTY:1AMANDA BOLLAND

0.500

0.9002 X 0.1260.70 BC

0.125

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 60 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-20Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-20

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER SPACER 3

QTY:1JUSTIN RUEGSEGGER

0.500

0.126 .07 BC

NOTE: PART FROM McMASTER # 2737T7

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 61 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-21Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-21

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHESSTEELMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER SPROCKET

QTY:1JUSTIN RUEGSEGGER

0.900

0.500

0.520

UNIVERSITY OF IDAHO ME DEPARTMENT

LINEAR:X. .1X.X .01X.XX .001X.XXX .005

SHEET 62 OF 62

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNIVERSITY OF IDAHO, ME DEPARTMENT. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UNIVERSITY OF IDAHO, ME DEPARTMENT IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

Stretch Armstrong

Part #: 7-22Scale: 2:1CAD ApplicationSolidWorks

DEFAULT TOLERANCES:

ANGULAR:X. 2X.X 1X.XX 0 30'

FILE NAME: 7-22

4/26/2009DATE:DRAWN BY:

DIMENSIONS ARE IN INCHES6061 ALUMINUMMaterial:THIRD ANGLE PROJECTION

CHECKED BY: DATE:

DESCRIPTION:

UPPER SPACER 4

QTY:1JUSTIN RUEGSEGGER

0-00Drawing View181Drawing View182

1a-00Drawing View1

1b-00Drawing View2

1c-00Drawing View3Drawing View4

1-21Drawing View12Section View A-A

1-51Drawing View189Drawing View190Section View A-ADrawing View192

1-52Drawing View9Drawing View10Drawing View11

1-61Drawing View183Drawing View185Drawing View186Section View A-ADrawing View193

1-62Drawing View5Drawing View6Drawing View7Drawing View8

2-00Drawing View14

2-01aDrawing View32Drawing View34Section View A-A

2-01bDrawing View29Drawing View31Section View A-A

2-01cDrawing View27Drawing View28

2-02Drawing View22Drawing View23Drawing View24Drawing View25Drawing View26

2-03Drawing View18Drawing View19Drawing View21Section View A-A

2-04Design BinderDrawing View16Drawing View17

3-00Drawing View145

3-01Drawing View146Drawing View147Drawing View148

3-02Drawing View149Drawing View150Drawing View151Drawing View152

4-00Drawing View35Drawing View36

4-01aDrawing View40Drawing View42Detail View A (1 : 1)

4-01bDrawing View37Drawing View38Section View A-A

4-02aDrawing View43Drawing View45Section View A-A

4-02bDrawing View46Drawing View48Detail View B (1 : 1)

4-03Drawing View49Drawing View50Drawing View51Drawing View52

4-07Drawing View53Drawing View54

5-00Drawing View153

5-01Drawing View154Drawing View155Drawing View156Drawing View157

5-02Drawing View158Drawing View159Drawing View160Drawing View161

5-03Drawing View162Drawing View164Drawing View165Drawing View166Section View A-A

5-04Drawing View173Drawing View175Drawing View176Drawing View177Section View A-A

5-08aDrawing View169Drawing View172Section View B-BSection View A-A

5-08bDrawing View167Detail View C (1 : 1.5)

6-00Drawing View55Drawing View56

6-01Drawing View57Drawing View59Drawing View60Section View A-A

6-02Drawing View61Drawing View63Section View A-A

6-03Drawing View64Drawing View66Section View A-A

6-04Drawing View67Drawing View69Section View A-A

6-05Drawing View70Drawing View72Section View A-A

7-00aDrawing View74

7-00bDrawing View73

7-01Drawing View75Drawing View77Drawing View78Drawing View79Section View A-A

7-02Drawing View80Drawing View81Drawing View82

7-03Drawing View83Drawing View85Section View A-A

7-04Drawing View86Drawing View88Section View A-A

7-05Drawing View89Drawing View90Drawing View91Drawing View92Drawing View93

7-06Drawing View94Drawing View96Section View A-ADrawing View97

7-07Drawing View98Drawing View99Drawing View100

7-08Drawing View101Drawing View102

7-09Drawing View103Drawing View104Drawing View105

7-10Drawing View106Drawing View107

7-12Drawing View108Drawing View109Drawing View110

7-13Drawing View117Drawing View118Drawing View119

7-14Drawing View120Drawing View121Drawing View122

7-15Drawing View123Drawing View124Drawing View125

7-16Drawing View126Drawing View127

7-17Drawing View128Drawing View129Drawing View130

7-18Drawing View131Drawing View132Drawing View133

7-19Drawing View134Drawing View135

7-20Drawing View136Drawing View137Drawing View138

7-21Drawing View139Drawing View140Drawing View141

7-22Drawing View142Drawing View143Drawing View144