Specification Guide Specification Guide

SpecificationGuide

Epicenter®

Epic® Casegoods

Exhibit™ Wall Rail Solution

Renegade™ Casegoods

WaveWorks® Casegoods

Specification Guide

Effective June 2, 2014


www.NationalOfficeFurniture.com

1205 Kimball Boulevard, Jasper, IN 47549800.482.1717 Fax 812.482.8800

©Kimball International, Inc. 2014Printed in the USAForm No. NSPEC Ver. 14A Unit of Kimball International

NPGC Specification Guide Cover_Ver 14_Layout 1 5/1/14 12:02 PM Page 1

Limited Lifetime Warranty

Limitations

Twelve Years Wood Chair Frames

Ten Years Seating Controls, Wood Veneers and Laminates

Five Years Mechanical and High Wear Parts Such As:Electrical Components, Polymer Based Components, Pneumatic Cylinders, Swivel Arm Pads, Casters, Chair Glides, Textiles, Foam, Covering Materialsand Decorative Trim

Exclusions

This warranty does not apply to:

• Damage caused by a carrier

• Normal wear and tear which is to be expected during the period of ownership

• Appearance, durability, quality, behavior, colorfastnessor any other attribute of COM (Customer’s Own Materials)or any other non-standard National material (including Arc-Com,Stinson, Maharam, Momentum, and Ultrafabrics) specified by the customer after application to a National product

• Color, grain or texture of wood, laminate and other covering materials

• Non-compliance with installation and maintenance instructions

• Electrical grommets where the box has been opened

• Damages or failures resulting from modifications, alterations,misuse, abuse or negligence or improper care and maintenanceof our products

NOTE: If using a protective glass top, always place felt spacer pads under the glass to allow the wood to breathe. A glass addition has the potential to accentuate deflection.

Gotcha™ 24 Hour Use Seating

Warranty on Gotcha 24 Hour Use models is 5 years from date of purchase for seating controls and pneumaticcylinders and 2 years from date of purchase for casters, textiles and foam.

Engineer-to-Order Products

National warrants all Engineer-to-Order products to be free from defects in workmanship given normal use and care for 3 years of single shift service.

Finish Warranty

Minor variations in finish color may occur due to the unique texture and grain of wood.

Follow these procedures to process warranty issues:

1. Contact National Customer Service (800.482.1717)and provide them with the serial number from theproduct in question and the purchase order numberor acknowledgement number and a detailed descriptionof the warranty issue. Serial numbers are mandatorybefore the claim can be processed.

2. Customer Service will determine and pre-approve allresolutions to the claim such as replacement units,service parts, labor and repair charges. Upon approval,resolutions will be assigned an uthorization number.

3. The authorization number must be included on all invoicesfor reimbursement. Any unauthorized charges will not be theresponsibility of National.

As the manufacturer of your furniture, we stand behindour craftsmanship and pledge to do everything we canto resolve any problems you may have within the termsof this warranty as quickly as possible.

There are no other warranties except as expressly setforth here, either expressed or implied including anywarranty of merchantability or fitness for any particularpurpose. We exclude and will not pay consequentialor incidental damages under this warranty.

National Office Furniture1205 Kimball BoulevardJasper, Indiana 47549800.482.1717Fax 812.482.8800www.NationalOfficeFurniture.com

National warrants that each piece of furniture will be free from defects in workmanship given normal use and care for as long as you, the originalcustomer, owns and uses the product.

Normal use is defined as the equivalent of a single shift, 40 hour work week. In the event that a product is used more than normal use, the applicablewarranty period will be reduced to 12 years and items that fall under different warranty limitations, as listed below, will be reduced to one-third(ex: Wood chair frames will be 4 years instead of 12 years). National, at its option, will repair or replace with comparable product any product,partor component shipped after September 1, 2000, if the claim is eligible under the conditions of this warranty. This warranty is valid only if the productis given proper care and maintenance.

At National, sustainability is embedded throughout the professional andpersonal fabric of our lives. That extends from our products and processesto the materials we provide you showcasing our solutions, such as thisprice list. It is printed on paper and is certified by the Forest StewardshipCouncil (FSC®), which lends the assurance of being sourced from sustainablymanaged forests.

This price list is available in printed form; however, we encourage you toconserve natural resources with us and consult the online version atwww.NationalOfficeFurniture.com/Resources.

Perhaps we’ve sent you more copies than you find necessary, or you no longer wish to receive our mailings. If so, please email us [email protected]. And as always, when you no longer have a need for this catalog, please recycle it.

Read more about our journey to create a better tomorrow atwww.NationalOfficeFurniture.com/Sustainability.

For more information about our products and services or to find a certified National® dealer near you, please visit us atwww.NationalOfficeFurniture.com or contact our Customer Service Team at 800.482.1717.

Intellectual Property

Acquaint®, Admire®, Arlington™, Arrowood™, Aurora®, Barrington®,Captivate®, Casbah®, Chameleon™, Cinch®, Clever®, Confide®, Davari®,Eloquence®, EnvyWorks®, Epic™, Epicenter®, Escalade®, Exhibit™,Flourish®, Franklin™, Fuel®, Fringe™, Gotcha™, Hiland™, IntegraClear®,Jiminy™, Journey®, Justice®, Medalist™, Mix-it®, Monterrey™, Myriad™,Pegos™, Pennant™, Remedy®, Renegade™, Reno®, Respect®, Result®,Roosevelt™, Staccato™, Swift™, Tag®, Timberlane™, Trimph™ andWaveWorks® are registered trademarks of National Office Furniture.Trademarks of other parties are identified wherever possible and Nationalacknowledges their rights.

BLOCKaide™ and Terratex® are registered trademarks of Interface, Inc.

Brisa®, Brisa® Distressed, Promessa® and Ultraleather™ are registeredtrademarks of Ultrafabrics, LLC.

Byrne Interlink® is a registered trademark of Byrne Electrical Specialists, Inc.

Corian® is a registered trademark of E.I. du Pont Nemours and Company.

Cradle to Cradle™ is a registered trademark of McDonough Braungart DesignChemistry, LLC.

Crypton®, Crypton® Green and INCASE™ are registered trademarks of Crypton, Inc.

Hi-Loft™, Hi-Loft2™, PERMABLOK3®, SILVERGUARD® and Silvertex™ areregistered trademarks of Spradling Holdings, Inc.

Hilti® Toggler® is a registered trademark of Hilti Corporation.

Indoor Advantage™ is a trademark of Scientific Certification Systems.

Intercoupler™ is a trademark of Power Logic SA (Pty), Ltd.

LEED® is a registered trademark of the U.S. Green Building Council.

level® is a registered trademark of BIFMA International.

Post-it® and Scotchgard™ are registered trademarks of 3M.

Repreve® and U Trust™ are registered trademarks of UNIFI, Inc.

Silverguard® is a registered trademark of Life Bioscience USA, LLC.

Velcro® is a registered trademark of Velcro Industries B.V.

Table of Contents

National Office Furniture—Specification Guide 1

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CONSOLIDATED STATEMENT OF LINE . . . . . . . . . . . . . . . . . . . . . . . . 6-18

PRODUCT OVERVIEWS

Exhibit™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 WaveWorks® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Epic™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23 Epicenter™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25 Renegade™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

PRODUCT INTEGRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-31

SUPPORT AND LOAD

Exhibit Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35 WaveWorks and Epic Support . . . . . . . . . . . . . . . . . . . . 36-37 Epicenter Support . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-41 Renegade Support . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-43

POWER AND DATA

Exhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 WaveWorks, Epic and Renegade . . . . . . . . . . . . . . . . . . 46-47 Epicenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-49

PRODUCT SPECIFICATION

Exhibit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-56 WaveWorks and Epic. . . . . . . . . . . . . . . . . . . . . . . . . . 57-65 Epicenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-73 Renegade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74-76 Cable Management/Work Tools and Accessories . . . . . . . 77-79

1-NOF_Intro-Cons_SOL 4/21/14 12:34 PM Page 1


Introduction


Welcome to Ultimate Flexibility

You’re here for a reason. You have something cool in mind and you want tomake it happen. You’re in the right place. At National, we like to make ithappen by making it as easy as possible to specify our furniture to fit yourdesign and budget goals. We understand the importance of planning andthe value of a quarter inch of space; it does matter. That’s why we’vedeveloped solutions that flex to various applications and uses. We have asea of sensible choices that offers unlimited configurations without beingoverwhelming. Let’s plan a spectacular space together.

The Choice is Yours

This guide features four product collections that work independently or canbe integrated: Epic, WaveWorks, and Renegade Casegoods, Epicenter andthe Exhibit Wall Rail Solution. This allows you to design freely creatingdesigns with layered surfaces, multiple storage solutions and a combinationof materials such as wood, metal, glass, resin and laminate. Exhibitprovides a unique solution by using the wall to support casegoods andstorage along with inserts for sharing ideas, displaying information andhousing organizational tools.

Other benefits of specifying our products include:

• expansive product offering including unique storage options,worksurface shapes, and surface materials

• maximize the use of space with the modular nature of theseproducts

• lighten the overall aesthetic with open support bases and use ofwall rail allowing more light to enter the workspace

• design specialized training, collaborative, and conferencing areas

• wall rail mounting provides easy access to building power and data

Get Comfortable: Planning Simplified

Designed to simplify the specification process by answering commonquestions about individual product lines and how products can integrate,this specification guide offers an organized, systematic approach to productplanning. The consolidated statement of line presents the components inthe order in which they are most effectively specified, while the overviewconfigurations show specific details about each series. It also providescritical information about:

• using Exhibit as the foundation for supporting upper storage andworksurfaces

• support and load requirements for fixed-wall and freestandingapplications

• power and data planning considerations

• Epicenter applications

And, don’t forget about the power and data conveniences and accessories.Considering how you’ll incorporate these elements into your design andtheir appropriate use will only enhance your customer’s experience once theproduct is in place. This guide outlines where these tools can be utilized.

• Organizational and work tools

• Vertical pigeon hole storage and other organizing stackers

• Exhibit tack board, marker board and slat wall inserts

• Privacy screens, monitor arms, keyboard trays and task lights

• Grommets and cable managers

• Epicenter capabilities

Quality, Reliability and Sustainability . . . It’s in There

You have enough things to worry about as you plan your space, so bychoosing National you have the assurance of quality, reliability andsustainability - enabling you to focus on your job.

Our products meet and exceed industry standards for performance anddurability. National is deeply committed to social and environmentalstewardship. So, you can plan on National being there for you and theenvironment.

Our products ensure the health and well-being of building occupants andthe environment, and have earned numerous independent third-partycertifications including:

• the Indoor Advantage™ label (meets indoor air quality criteria)

• Forest Stewardship Council (FSC®) certification signifyingsustainable forestry practices

• ANSI/BIFMA e3 Sustainability Standard level® 2 or level® 3certification

For detailed certification information by product series, visit NationalOfficeFurniture.ecoscorecard.com.

To measure our progress, we annually publish a detailed Corporate SocialResponsibility (CSR) report that offers a thorough analysis of ourperformance in the areas of zero-waste operations, life cycle assessments,chemicals of concern identification, energy evaluation and more. To accessthis report, visit our website at NationalOfficeFurniture.com/Sustainability.




Consolidated Statement of Line



6 National Office Furniture—Specification Guide

Application KeyE EpicR RenegadeW WaveWorks

Nationals’ consolidated pallet of products provides a variety of solutions designed to accommodate any design challenge.

The following items are keyed to illustrate which components are available within each product line to help make your planning and specification process simple.

Desks

Arc Top—Full Pedestal Arc Top— ¾ Pedestal Full Pedestal ¾ Pedestal Glass Top Arc Top—Full Pedestal Arc Top— ¾ Pedestal Full PedestalLeft/Right Left/Right Left/Right Left/Right

R W R E R W R W W R W R E R W

¾ Pedestal U-Shaped U-Shaped U-Shaped P-Shaped P-Shaped P-Shaped J-Shaped with Modesty Panel Worksurface Height Box/File Height with Modesty Panel Worksurface Height Box/File Height Worksurface Height

End Panel End Panel Left/Right End Panel End Panel End PanelLeft/Right Left/Right Left/Right

R W E R W E R W R E R W E R W R R

Corner Units

Corner Unit Extended Corner UnitFullLeft/Right

R W R W

Returns and Bridges

Return Box/Box/File Return File/File Space Saver Return Space Saver Return Return Return Shell BridgeLeft/Right Full Pedestal File/File Full Pedestal Box/File ¾ Pedestal Box/File ¾ Pedestal Left/Right

Left/Right Left/Right Left/Right Left/Right

E W E R W R R R W R W E R W

Shells

Freestanding Freestanding Linkable Return Linkable Bridge Space Saver Credenza Worksurface Height/ Worksurface Height Left/Right with Narrow/Narrow Linkable Return Worksurface Height/Box/File Height Box/File Height Panels Left/Right Box/File HeightFull End Panels End Panel

Left/Right

R W R R W R R R W





Credenzas

Kneespace Kneespace Single Pedestal Single Pedestal Single Pedestal Single Pedestal Extended Credenza MediaFull Pedestal ¾ Pedestal File/File Box/File Lateral File Box/Box/File Left/Right

Left/Right ¾ Pedestal Left/Right File/FileLeft/Right Left/Right

E R W R W E R W R W E R W E W E W

Buffet/Entertainment Storage Lateral File Lateral File/ ¾ PedestalDouble Door

R W E R W E R W R R

Reception Units

ADA Main Shell Main Shell Return with Return Bridge with Counter Kits Transaction CounterLeft/Right Transaction Surface Left/Right Transaction Surface

Left/Right

W R W W R W R W W W

Set-on Surface Storage38" High

Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer Resin/Glass Doors No Doors Sliding Doors Open Back Open Back Recessed Doors Metal/Laminate

No Doors Metal Flipper Doors

E R W R W E R W E W W W W

Corner Highback Corner Highback Corner Highback Corner Highback Corner Highback Bookcase with Bookcase with Open BookcaseOrganizer Organizer Organizer Organizer Organizer Glass Doors DoorsGlass Doors No Doors Extended

Left/Right

W W W R R W E R W E R W

1915⁄16"





Set-on Surface Storage50" High

Entertainment Highback Organizer Highback Organizer Corner Highback Corner Highback Bookcase with Bookcase with Open BookcaseCabinet Glass Doors Organizer Organizer Glass Doors Doors

Glass Doors

W W W W W W E R W E R W

Entertainment Cabinet

W

Overhead/Set-on Surface Storage13" High

Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead StorageCabinet Cabinet Cabinet Cabinet Cabinet Cabinet Open Cabinet CabinetWall Mount Sliding Doors No Doors Exhibit Mount Sliding Doors No Doors Sliding Doors Sliding Doors

Wall Mount Wall Mount Exhibit Mount Exhibit Mount Set-On Surface Set-On Surface“O” Supports “U” Supports

E E E E E E E E

Overhead Storage Overhead Storage Overhead Shared Overhead Shared Overhead Shared Overhead SharedCabinet Cabinet Storage Cabinet Storage Cabinet Storage Cabinet Storage CabinetNo Doors No Doors Sliding Doors Sliding Doors No Doors No DoorsSet-On Surface Set-On Surface Left/Right Left/Right Left/Right Left/Right“O” Supports “U” Supports Set-On Surface Set-On Surface Set-On Surface Set-On Surface

“O” Supports “U” Supports “O” Supports “U” Supports

E E E E E E

Epicenter Overhead Storage13" High

Overhead Storage Overhead Storage Overhead Shared Overhead Shared Overhead Storage Overhead StorageCabinet Cabinet Storage Cabinet Storage Cabinet Cabinet CabinetSliding Doors No Doors Sliding Doors No Doors Single Sided Single Sided

Left/Right Left/Right Sliding Doors No Doors

E E E E E E





Overhead Storage (continued)17" High, 18" High

Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead StorageCabinet Cabinet Cabinet Cabinet Recessed Door Cabinet Cabinet CabinetResin/Glass Doors Wall Mount Sliding Doors No Doors Exhibit Mount Glass Doors Exhibit Mount Sliding DoorsWall Mount Wall Mount Wall Mount Metal Exhibit Mount Exhibit Mount

R W E R W E E R W W W E W E

Overhead Storage Overhead Storage No Doors Flipper DoorExhibit Mount Exhibit Mount

Metal

E W W

30" High

Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Cabinet Cabinet No Doors Cabinet Cabinet No Doors Glass Doors Wall Mount Wall Mount Glass Doors Exhibit Mount Exhibit MountWall Mount Exhibit Mount

W W W W W W

Lateral Files and Storage Cabinets

Lateral File Lateral File Lateral File Double Door Unit Multi-File Storage Mixed Storage Freestanding Mobile Utility CartTwo Drawer Three Drawer Four Drawer Cabinet Cabinet Box/File

E R W E R W E R W E R W E R W E R W E W

Mobile Computer Cart Lateral File Lateral File Lateral File Lateral FileTwo Drawer Three Drawer Four Drawer Five DrawerMetal Metal Metal Metal

W W W W W


Vertical Storage Towers405⁄16" High, 5215⁄16" High

Wardrobe/ Storage/ Storage/ Storage Front Bookcase Storage Front Bookcase 90° Storage 90° Storage 90° StorageStorage Cabinet Wardrobe with Wardrobe with Wardrobe with Wardrobe with Bookcase/Wardrobe Bookcase/Wardrobe BookcaseSingle Door File/File File/File File/File File/File with File/File with File/File with File/FileLeft/Right Left/Right Left/Right Left/Right Left/Right Left/Right Left/Right Left/Right

E E E E E E E E

90° Storage Storage Front Bookcase Storage Front Bookcase Wardrobe Cabinet Wardrobe Cabinet Wardrobe/ Storage Cabinet Storage/LateralBookcase with File/File with File/File Double Door Double Door Storage Cabinet Double Door File Cabinetwith File/File Left/Right Left/Right Double DoorLeft/Right

E E E E E E E E

Storage/Lateral Storage Cabinet Storage CabinetFile Cabinet Bookcase with Bookcase with

File/File File/FileLeft/Right Left/Right

E E E

537⁄8" High, 6515⁄16" High

Storage Cabinet Storage/Wardrobe Storage BookcaseFile/File File/File Wardrobe Metal Metal File/File

Metal

W W W

667⁄8" High

Wardrobe/Storage Storage/Wardrobe 90° Storage 90° Storage Wardrobe/Storage Storage Cabinet Storage/Lateral WardrobeCabinet with File/File Bookcase/Wardrobe Bookcase Cabinet Double Door File Cabinet Double Door Single Door Left/Right with File/File with File/File Double DoorLeft/Right Left/Right Left/Right

E R W E R W E R W E W E W E R W E R W E R








Vertical Storage Towers667⁄8" High

Storage Cabinet Storage Front Bookcase Storage Front Bookcasewith File/File Wardrobe with with File/FileLeft/Right File/File Left/Right

Left/Right

E W E E

67¼" High, 79¼" High, 7911⁄16" High

Wardrobe/Storage Storage/Wardrobe 90° Storage 90° Storage Wardrobe/Storage Storage Cabinet Storage/Lateral Storage CabinetCabinet with File/File Bookcase/Wardrobe Bookcase with Cabinet Double Door File Cabinet with File/FileSingle Door Left/Right with File/File File/File Double Door Left/RightLeft/Right Left/Right Left/Right

W W W W W W W W

Media Storage TowerSingle Door(79 11⁄16" only)Left/Right

W

Bookcases

One Shelf Two Shelf Bookcase Three Shelf Four Shelf Bookcase Five Shelf BookcaseOpen Bookcase Open Bookcase with Doors Open Bookcase Open Bookcase with Doors Open Bookcase with Doors

E W E R W W E R W R W W W W

Open Bookcase Open Bookcase Open BookcaseTwo Shelf Three Shelf Four ShelfMetal Metal Metal

W W W


Mobile Pedestals

Mobile Pedestal Mobile Pedestal Mobile Pedestal Mobile Pedestal Mobile Pedestal Mobile Pedestal w/PullFile/File Box/File Box/File with Top Cushion Top Cushion Top Cushion Top

Metal

W W E R W E R W W W

Worksurfaces

Rectangular Tapered Angled Concave Corner Extended Corner Arc U-Shaped

E W E W E W E W E W W E W

Extended U-Shaped Elliptical U-Shaped P-Shaped Elliptical P-Shaped Extended P-Shaped Elliptical Extended 120° Corner J-ShapedP-Shaped

E W E W W E W W W E W

Island Extension Round Half Round D-Shaped Quarter Round Extended Quarter Square Cornice TopRound 15" and 24" Deep

W E W E R W W W W E W W

Component Top for Worksurface WireLateral Files Manager Filler

R E W

Undersurface Storage SupportWorksurface Height

Box/Box/File File/File Support Pedestal Lateral File Double Door Unit Double Door Unit Bookcase Mixed Storage CabinetSliding Doors

E R W E R W E E R W E R W E E R W E R W







Undersurface Storage SupportWorksurface Height

Multi-File Cabinet Box/File Storage Cabinet Box/Box/File File/File Lateral File Double Door Multi-FileUndersurface Metal Sliding Undersurface Undersurface Undersurface Undersurface UndersurfaceSuspended Shelves Metal Metal Metal Metal Metal

E R W R E W W W W W W

Mixed Storage Open Bookcase Box/FileUndersurface Undersurface Undersurface/HangingMetal Metal Metal

W W W

Box/File Height

Storage Cabinet Bookcase Lateral File Box/File Box/Lateral File Box/File Box/Lateral File Box/File BookcaseMetal Sliding Undersurface Undersurface Undersurface UndersurfaceShelves Metal Metal Metal

E W E R W R W E W E W W W

Surface Supports

End Panels Support Panels U-Style Supports Box/File Height T-Panel Support Corner Post Counter and Bar Height Static and Mobile Supports Full and Box/File Metal Square and Round Column Legs

Heights Support Bases

E W E W R E W R E W E W W E W R E W

Static and Mobile Half Wood Counter and Bar Height Counter and Bar Height Counter and Bar Height Counter and Bar Height Counter and Bar Height Counter and Bar HeightAdjustable Height Support Base “H” Style “U” Style “U” Style Support Base Kits Support Base Kits Support Base KitsColumn Pin Legs End Supports End Supports End Supports “H” Style “U” Style “U” Style with Insert

with Insert

E W W E W R E W R E W R E W R E W R E W R

Double Depth Base Double Depth Base28" High Model w/Insert

28" High Model



Surface Supports

Static and Mobile Height Adjustable Counter and Bar Height X Base X Base Static and Mobile Adjustable Height Four Star Bases Four Star Base Four Star Bases Adjustable Height Static and Mobile C-Legs Static C-Leg

Mobile Pin Adjustment

E W R E W R E W R E W R E W R E W E W

Static and Mobile Manual (Hand Crank) Electric Adjustable Manual (Hand Crank) Electrical Adjustable Disc Base Counter and BarT-Legs Adjustable Height Base Adjustable Height Height “L” Base Height Disc Base

Height Base “L” Base

E W E W E W E W E W E W E W

Soft Square Base Counter and Bar Height Worksurface Worksurface to Corner Support End Panel End PanelSoft Square Base Undersurface Support Storage Bracket Privacy Panel Metal Box/File

Rail Metal

E W E W E W R E W E W W W

Half End Panel Support Panel Support Panel Return Support Panel Gusset Bracket Epicenter End Epicenter MidMetal Metal Box/File Metal Metal Support Privacy Support Privacy

Metal Panel Panel

W W W W W E W E W







Modesty Panels and Privacy Screens

Full Height Box/File Height 1⁄3 Height Modesty Mesh Modesty Panel 1⁄3 Height Metal 1⁄3 Height Resin Tapered Acrylic Rectangular Acrylic Modesty Panel Modesty Panel Panel Modesty Panel Modesty Panel Privacy Screen Privacy Screen

E W E W W W E W E W E R W E R W

Rectangular Felt Edge Mounted Edge Mounted Edge MountedPrivacy Screen Privacy/Modesty Privacy Screen Privacy Screen

Screen Rectangular Tapered

E R W E R W E R W E R W

ExhibitExhibit Rails

Exhibit Wall Exhibit Wall andRail Faceplate

Exhibit Inserts

Tack Board Inserts Marker Board Inserts Slat Wall Inserts Slat Wall with Organizer ShelfTack Inserts Inserts

Exhibit Worksurface Brackets and Trim

Full End Trim Trim Channels Single End Cap Vertical Cable Manager Worksurface Filler StripsMounting Bracket




EpicenterEpicenter and Brackets/Trim

Upper Epicenter Upper Epicenter Lower Epicenter Universal Epicenter Epicenter Epicenter Epicenter Filler Epicenter Trim CapMulti-Circuit Non-Powered Attachment Bracket Worksurface End Trim Strip Kit

Set Mounting Brackets

Epicenter Inserts and Screens

Tack Board Insert Marker Board Insert Slat Wall Insert Slat With Tack Insert Tapered Rectangular Single Sided Single Sided Privacy Screen - Privacy Screen - Insert - Insert - Epicenter Mount Epicenter Mount Tack Board Veneer

Single Sided Modesty Panel Insert Modesty Panel InsertInsert - Veneer LaminateLaminate

Epicenter Supports

Double Depth Base Double Depth Base Base Support Base Double Depth Base Base Epicenter Double Epicenter End Panel28" High Model w/Insert 28" High Model 28" High Model 6" High Model 6" High Model Depth End Panel 28" High Model

28" High Model 28" High Model

Epicenter Double Epicenter End Panel Epicenter End Epicenter End Epicenter Mid Epicenter MidDepth End Panel 6" High Model Support Privacy Support Privacy Support Privacy Support Privacy6" High Model Panel Panel Panel Panel

Epicenter Power and Data

Power Entry Whip Jumper Duplex Receptacles Power Pole Vertical Wire Horizontal Wire Hardwire KitManager Manager




Accessories

Vertical Pigeon Organizing Stacker Lower Storage Tack Boards Marker Boards Slat Walls Task Lights Metal Storage CubbyHole Storage Cushion

Work Tools

Center Drawers Storage Trays Keyboard Tray Keyboard Tray/ Keyboard Kits Flexible Single Flexible Single Mouse Pad Monitor Arm Monitor Arm

Pole Mount Grommet Pole Mount Clamp

Flexible Dual Flexible Dual Triple Mount Monitor Arm Monitor Arm Monitor Arm KitPole Mount Grommet Pole Mount Clamp

CPU Holder Metal Corner Sleeves CPU Cart Mobile Desk Pad Waste Container Pencil Tray Box Drawer Divider Overhead/ShelfDivider

Deluxe Drawer Organizer

Metal Work Tools

Shelf Single Side Tray Double Side Tray Pocket Organizer Slant Sorter Binder Shelf Marker Holder

Black and Clear Plastic Work Tools

Pencil Cup Legal Paper Accessory Tray Phone Holder Binder Shelf Slant SorterTray




Power/Data Products

Power/Data Center Convenience Corner Channel Power Director Power Center Power/ Power Tower Cable ManagersOutlet with Power Communication and Covers

Center

Byrne Interlink® One Touch Pivoting One Touch Pivoting One Touch Pivoting Byrne Interlink Byrne Interlink Power Grommet Powerlogic System Power/Data Grommet Power Grommet Power Grommet IQ System IQ System (G23) Intercoupler™ System

(G17) (G172) (G173) Power/Data Power Grommet (Undersurface)Grommet

Worksurface Undersurface Horizontal WireGrommets Wire Managers Manager




Product Overview

2-NOF_ProductOverview 4/21/14 12:34 PM Page 19

Product Overview


Exhibit Wall Rail SolutionBy making efficient use of wall space, Exhibit wall rails, inserts and worksurface mounting bracketsprovide the infrastructure support within private offices and the perimeter foundation for manyenvironments. Exhibit may also be used at any height within training rooms, common areas,mail/copy rooms, and conference space to support interaction.

Wall rails and inserts also capitalize on vertical wall space to support personal organization andcollaboration tools within the work space.

Exhibit wall rails, tack board inserts and HPL marker board inserts may be field scribed to adapt toalmost any wall length and configuration.

Worksurfacemounting bracketsare available toprovide attachmentof a broad range ofworksurface typesand sizes

Faceplates required to secure inserts within wall rails

Lower rails providesupport for worksurfacesanywhere along the rail

Vertical cablemanager concealsand routes task light cords

Tack board, marker board, organizer shelves, slat wall and slat/tack inserts provide personal organization and collaboration

Upper rails provide support for overheadstorage anywhere along the rail

Full end trim and end capscreate a finished appearanceat the end of a run

Upper wall rail

Lower wall rail

Faceplate

Full end trim

Inserts

Worksurface brackets

Work tools are available toattach anywhere along the slatwall insert


Product Overview


WaveWorksWaveWorks Casegoods offer freestanding or Exhibit supported worksurfaces and storage options forprivate office, collaborative and open plan environments. Conference and training solutions are alsoprovided through a variety of surface and support options.

WaveWorks metal storage and privacy components are also available to provide alternative solutions.

WaveWorks may be planned and specified using assembled or component products.

Modified sizing available on WaveWorks worksurfaces, modesties and end panels.

Overhead storage in set-on,wall mount or Exhibit mount,with or without doors

Multiple storage height options

Worksurfaces available13⁄16" or 19⁄16"thickness with wiremanagers, surfacegrommets, and belowsurface cablemanagement (availableseparately)

Several power/datacomponents are availableto bring access to theworksurface

Widths available to match worksurface widths

Multiple worksurface supportoptions available to provideproper support as well asunique aesthetics

Set-on storage

Choose from several worksurfacetypes, sizes and rim profiles

Tack boards and slat wallsmay be added

Worksurface height storage

Freestanding storage:From mobile pedestals, lateral files and bookcases to wardrobes and storage towers

Two undersurface storage heights available:worksurface and box/file height

Box/File height storage

Modesty panels available

Overhead storage in set-on,wall mount or Exhibit mount,with or without doors


Product Overview


EpicEpic Casegoods offer freestanding or Exhibit supported worksurfaces and storage options for privateoffice, collaborative and open plan environments.

Epic’s footed base design offers a lighter aesthetic within the work space.

Epic may be planned and specified using assembled or component products.

Modified sizing available on Epic worksurfaces, modesties and end panels.

Multiple worksurface support optionsavailable to provide proper support as wellas unique aesthetics

Choose from severalworksurface types, sizesand rim profiles

Worksurfaces availablewith integrated wiremanagers, surfacegrommets, and belowsurface cablemanagement (availableseparately)

Privacy screens available

Worksurface height storage

Footed base design creates alighter scale aesthetic

Modesty panels available

Freestanding storage:From pedestals, lateral files and bookcasesto wardrobes and storage towers

Box/File height storage

Two undersurface storage heights available:worksurface and box/file height


Product Overview


Overhead set-on storage available with “U” style stanchions (worksurface defacing) and “O” style stanchions (non-defacing) options that are available with sliding doors or without doors

Multiple worksurface supportoptions available to provideproper support as well as uniqueaesthetics

Choose from several worksurfacetypes, sizes and rim profiles. Worksurfaces available with integrated wire managers, surface grommets and below surface cable management (available separately)

Overhead storage in set-on, wallmount or Exhibit mount withhinged doors, sliding doors orwithout doors

EpicEpic Casegoods offer overhead storage in set-on, wall mount or Exhibit mount with hinged doors,sliding doors or without doors.


Product Overview


EpicenterEpicenter mounts to WaveWorks or Epic undersurface storage and support bases within private office,collaborative and open plan environments.

Epicenter is supported by the undersurface storage or support bases and provides support forperpendicular worksurfaces and power/data capabilities.

Available with a multi-circuit solution or non-powered. Powered Upper Epicenter frames may beconnected directly to building power at the floor, wall or ceiling to manage and deliver power anddata to the beltline of the workstation.

Epicenter overheadstorage straddlesthe Epicenter frame

Worksurface mounting brackets attach to the slat insert of the Epicenter frameallowing theworksurface toattach anywhere

Privacy screens attachanywhere along the topof the Epicenter top cap

Power and data access is availableon one or both sides of thepowered Epicenter

End trim

WaveWorks or Epic box/fileheight undersurface storagewithout the end panel grommetor back panel option

Epicenter filler strip

Power and power/data options for tack boardand slat/tack board insert

Upper inserts available in tack board, marker board, slat wall and slat/tack board

Accessories and work tools are available to attachanywhere along the slat insert

WaveWorks or Epic worksurfaceheight undersurface storagewithout the end panel grommet

Epicenter trim caps must be specified separatelyto go on top of the Epicenter. The trim cap runsbelow the overheads and the Epicenter mountedprivacy screen is attached to the trim cap

Upper Epicenter


Product Overview


EpicenterEpicenter can be specified for a double or single sided application. Epicenter double sided consists ofan Upper Epicenter that must be supported by undersurface storage or Epicenter supports and aworksurface.

Epicenter single sided consists of an Upper and Lower Epicenter that must be supported byundersurface storage or Epicenter supports and a worksurface. Upper and Lower Epicenters must bespecified at the same widths.

Modesty panel insert sizing must be specified after the undersurface storage or Epicenter supports arespecified. Modesty panel inserts will run between undersurface storage and end support panels.Modesty panel inserts will run behind Epicenter support bases. Modified sizing available on modestypanel inserts.

Power and data access is availableon one or both sides of the powered Epicenter

Privacy screens available

Epicenter trim caps must bespecified separately to go ontop of the Epicenter

Epicenter endtrim must be specified separately

Epicenter trim capmust be specified separately

Epicenter modestypanel insert availablein modified sizing

End support privacy panels provideworksurface end support and alsoprivacy. Available in double or singlesided Epicenter applications

Mid support privacy panels are available in double or single sided Epicenter applications

Power and power/datapass through is availablewhen specifying an Epicenteron each side of the midsupport privacy panel


Product Overview


RenegadeRenegade Casegoods offer freestanding desks and storage options for private office, collaborative andopen plan environments.

Renegade may be planned and specified using assembled or component products.

Renegade desking shells may also be used with WaveWorks and Epic undersurface storage

Several single circuitpower/data components areavailable to bring access tothe surface

Storage widths and depths aresized for a clean vertical line

Choose from several worksurfacetypes and sizes, in shell or deskconfigurations

Privacy panels available

Shells with box/file heightor full surface height endpanels are available

Freestanding box/fileheight shell

Use cushion forguest seating

Shells may belinked together tocreate collaborativeenvironments

Set-on storage

Tack boards may be addedCan be wall mounted or withina highback organizer

Overhead storage in set-on orwall mount with or without doors

Desks may be specified withsuspended box/file or fullheight pedestals

Freestanding storage:From lateral files and bookcasesto wardrobes and storage towers



Product Integration


Product Integration


IntegrationSelected products within WaveWorks, Epic, Renegade and Exhibit may cross over between productlines to offer solutions that achieve greater flexibility, aesthetics and price points.

You may select worksurfaces from one product line and utilize undersurface storage from anotherproduct line. Or utilize the undersurface storage and worksurfaces from one product line andincorporate set-on and wall mount storage from another line.

You may even layer heights of surfaces and storage to realize your own unique design solution. Wedo recommend that you consider the base design of each storage product when considering whichcomponents to place directly adjacent to each other.

Here are some standard typical examples showing the integration of components between productlines.

Epic and ExhibitEpic Exhibitmounted storage

Epic box/file heightpedestals

Choose any appropriateworksurface support to fit yourdesign requirements

Several modesty paneloptions are available

Exhibit wall rails

Exhibit inserts

Exhibit full end trim

Exhibit supported Epic kniferim worksurface

Tack board insert field scribed to matchEpic knife rim worksurface depth

Specify the softened rimprofile for worksurfaceson box/file heightundersurface storage

WaveWorks set-onoverhead storage

Epic knife rimsurfaces

Use any freestanding storage components

Worksurface heightEpic support pedestals



Epic and WaveWorks


Product Integration


Epic, WaveWorks and Exhibit GRAPHIC KEY

Graphics are illustrated with a shaded technique to help you quickly identify which products to focus on.

Primaryproduct

Secondary orsupportingproduct

Epic support pedestalsSeveral modesty paneloptions are available

WaveWorksset-on storage

WaveWorks Exhibitmounted storage

Epic worksurfaceheight storage

Exhibit wall rails

Exhibit inserts

Exhibit full end trim

Epic knife rim surfaces

Tack Boards may be field scribed to matchEpic knife rim worksurface depth

Several privacy paneloptions are available

Renegade shells withbox/file height and worksurface heightend panels

Renegade shells withbox/file height end panels

WaveWorks box/fileheight metal storage

Renegade and WaveWorks


WaveWorks and Epicenter Double Sided ApplicationWORKSURFACE HEIGHT

Wire manager filler must bespecified separately to capthe end of a worksurfacewhen a wire manager is specified

End trim model mustbe ordered based uponapplication

WaveWorks freestandingstorage components


WaveWorksworksurfaces

Upper Epicenter

Epicenter mountedprivacy screen

WaveWorks worksurfaceheight undersurfacestorage without the endpanel grommet or backpanel option

WaveWorks worksurfaces mustbe specified with a modifieddepth of 227⁄16" or 285⁄8" to align with the Epicenter

Product Integration


WaveWorks and Epicenter Double Sided Application GRAPHIC KEY


Primaryproduct


WaveWorks and Epicenter Double Sided ApplicationBOX/FILE HEIGHT



WaveWorks box/fileheight undersurfacestorage without the endpanel grommet or backpanel option

WaveWorks worksurfaces mustbe specified with a modifieddepth of 227⁄16" or 285⁄8" to align with the Epicenter

WaveWorks worksurfacessupported by Epicenter

Epicenteroverhead storage


Edge mount modesty/privacy screens available

End trim

Epicenter single sidedoverhead storage

Epicenter single sidedoverhead back panel;must be specified separately

Product Integration


GRAPHIC KEY


Primaryproduct


WaveWorks/Epic and Epicenter Single Sided ApplicationEpicenter single sided application mounts to WaveWorks or Epic storage within private office,collaborative and open plan environments.

Epicenter single sided must be supported by undersurface storage or Epicenter supports and aworksurface.

Epicenter single sided consists of an Upper and Lower Epicenter; Upper Epicenter inserts for the userside and single sided inserts for the approach side.

Available with a multi-circuit solution or non-powered in the Upper Epicenter section. PoweredEpicenter frames may be connected directly to building power at the floor, wall or ceiling to manageand deliver power and data to the beltline of the workstation.

Modesty panel insert sizing must be specified after the undersurface storage or Epicenter supports arespecified. Modesty panel inserts will run between undersurface storage and end support panels.Modesty panel inserts will run behind Epicenter support bases.

Single sided Epicenter overheads have an unfinished back. An overhead back panel must be specifiedseparately when using the overhead in an open plan.

Epic and Epicenter Single Sided ApplicationBOX/FILE HEIGHT

WaveWorks and Epicenter Single Sided ApplicationWORKSURFACE HEIGHT


Epicenter modesty panelinsert available in modifiedsizing

Epicenter mounted privacyscreens must be mounted tothe Epicenter trim cap




Support and Load

3-NOF_SupportLoad 4/21/14 12:34 PM Page 33

Support and Load


Exhibit Wall Rail SolutionExhibit consists of upper and lower rails thatsupport worksurfaces, overhead storagecomponents and Exhibit inserts.

Exhibit rails attach at desired height directly toload bearing walls constructed of wood or metalstuds, poured concrete or concrete block wallswith fasteners appropriate to the wall material.

WALL REQUIREMENTS

STUD WALLSWood studs must be a minimum of 2 x 4’ssecured to the floor and ceiling.Maximum height of 14’.

METAL STUDSMetal studs must be minimum 20 gauge “C”channel secured to the floor and ceiling.Maximum height of 14’.

POURED CONCRETE AND CONCRETE BLOCKAttach rails with appropriate fasteners for wallmaterial.

STRENGTHWalls must resist no less than 5 lbs. per squarefoot of force applied perpendicular to the walland the deflection can not exceed 1⁄240 of thespan for brittle finishes and 1⁄120 of the span forflexible finishes.

ATTACHMENTRails must be fastened a maximum of every 24". Rails may not extend more than 6" beyondattachment point.

WIDTHSProperly fastened, there is no maximum lengthrequirements for Exhibit rail runs.

MINIMUM WITH INSERT ONLY.Minimum rail length is 18" on 16" centeredmounting points.

MINIMUM TO SUPPORT COMPONENTS.Minimum rail length is 30" centered on 24"mounting points.

MOUNTING HEIGHTSStandard height to the center of the lower rail is28½" from the finished floor to accommodateundersurface storage.

Upper rail height is determined by the insertheight, storage component supported andadjacent freestanding components.

Refer to product specification section page 42for information on proper heights to coordinateWaveWorks and Epic components as well as bar,counter and worksurface height applications.

REQUIRED

Maximum 24" on center

Maximum 14’

Secured

Secured

Wood or metal studs,concrete block orpoured concreteconstruction

Rails fastened every24" maximum

Exhibit rails

ATTACH

6" maximum

WIDTHS

18" minimum

Inserts only

30" minimum

Components support

HEIGHTS

28½"

63¾"

661⁄16"

66½"

777⁄8"785⁄16"


Support and Load


Exhibit Rail AttachedWorksurface SupportExhibit lower rails will support worksurfaces inlinear and perpendicular configurations anywherealong the rail.

WORKSURFACE BRACKETSAny width or depth WaveWorks or Epicworksurface may be attached to the Exhibitlower rail when supported by worksurfacebrackets.Up to 48" requires 2 brackets.Up to 72" requires 3 brackets.Longer than 72" requires 4 brackets.

EXHIBIT RAIL ATTACHED OVERHEAD STORAGE

Exhibit upper rail will support WaveWorks andEpic overhead storage components anywherealong the rail. Gang multiple componentstogether for a clean, straight run.

OTHER SUPPORT ISSUESExhibit slat wall inserts will support anycombinations of work tools and one slat mountmonitor arm every 24".

EXHIBIT SLAT WALL INSERTSWall fasteners are NOT required under thefollowing conditions:

• If slat wall inserts are to support lessthan 40 lbs., wall fasteners are notrequired.

• When weight is distributed evenly aboveand below center of slat wall, the slatwall can hold up to 160 lbs. withoutusing wall fasteners. At least half of theweight must be applied above center ofslat wall. Deflection or bowing occurswhen not enough counterweight isapplied to the upper half of slat wall.

• Any slat wall inserts used in conjunctionwith overhead storage units will not needwall fasteners. Overhead units must fullycover the slat wall.

Wall fasteners are to be used under the followingconditions:

• If slat wall inserts are to support 160 lbs.or more, wall fasteners are to be used.

• Bottom loading, (placing the majority ofload below centerline of slat wall), causesthe slat wall to deflect or bow from fixedwall. If slat wall inserts are to be loadedwith more than 50% of load on thebottom half, wall fasteners must beinstalled.

When required, two fasteners are required perslat wall insert. Fasteners are to be inserted inthe center slat, approximately 1 inch off of edge“U” trim, or to nearby stud.

Worksurface brackets

Any WaveWorks or Epic worksurface

Lower rail

Undersurface support rail

Upper rail

WaveWorks or Epicoverhead storage

Slat wall insert supports work tools(a work tool can hold up to 8 lbs.)

REQUIRED SUPPORT13⁄16" thick.Require support every 48".19⁄16" thick.Require support every 60".

Undersurface support rail available to supportsurfaces up to 72"

Consider additional support where heavy loadsare anticipated.

Surface support is required wherever 2 surfacesmeet end-to-end.

In place of end panels, corner surfaces may besupported by a support base at the back cornerwhen connected to an adjacent surface.

EXHIBIT SLAT WALL INSERTS COMBO SLAT/TACKWall fasteners are NOT required under thefollowing conditions:

• If slat wall inserts are to support lessthan 40 lbs., wall fasteners are notrequired.

Wall fasteners are to be used under the followingconditions:

• If slat wall inserts are to support 40 lbs.or more, wall fasteners are to be used.

When required, two fasteners are required percombo/tile slat wall insert. Fasteners are to beinserted in the top slat, approximately 1 inch offof edge “U” trim, or to nearby stud.

FASTENERSDry wall – #8 x 1½" plastic toggle anchor, withblack panhead screw

Wood Stud – #8 x 1½" black panhead screw

Concrete or brick – #8 x 1" plastic conical anchorkit with black panhead screw


Support and Load


WaveWorks and EpicComponent WorksurfaceSupportFollow these guidelines when planning for Epicand WaveWorks component worksurfaces.

CONFIGURATION TYPESFreestandingLinear runs“L” Shaped return or box/file height support“U” Shaped bridge or return

WORKSURFACE SUPPORTAll surfaces, in any configuration, must besupported at a minimum of one end by anExhibit rail, a support pedestal, support base,end panel, or a metal support base.

Undersurface support rail available to supportsurfaces up to 72".

REQUIRED SUPPORT13⁄16" thick;Require support every 48".19⁄16" thick;Require support every 60".



Surface support is required wherever 2 surfacesmeet end-to-end.

In place of end panels, corner surfaces may besupported by a support base at the back cornerwhen connected to an adjacent surface.

WORKSURFACE BRACKETSFlat brackets connect worksurfaces in “L” and“U” configurations and are shipped withworksurfaces when specified as an extension(qty. 2) or filler (qty. 4).

Freestanding

“U” Bridge “U” Return

“L” Return “L” Box/File

13⁄16" thick surface 19⁄16" thick surface

Any surface end-to-endSupport base

48" maximum

Supportrequired

60" maximum

Supportrequired

Flatbrackets

Supportrequired

End supportrequired

Supportrequired

Supportrequired

WITH SUPPORT PANELS

TOP DOWN VIEW TOP DOWN VIEW

End SupportRequired

UndersurfaceSupport Rails

OR... WITH UNDERSURFACE SUPPORT RAILS

Linear

Linear

Linear

Linear

Corner support panel


Support and Load


WaveWorks and EpicComponent Storage SupportFollow these guidelines when planning foroverhead and set-on storage components.

PROPER SUPPORTEXHIBIT RAIL MOUNTEDAny WaveWorks or Epic Exhibit mount overheadstorage component may be supported by Exhibitupper rails.

Consider rail height when planning for adjacentset-on and freestanding storage for properalignment.

WALL MOUNTEDAny size WaveWorks and Epic overhead storagecomponent may be attached at desired heightdirectly to load bearing walls constructed ofwood or metal studs, poured concrete or concreteblock walls with fasteners appropriate to the wallmaterial.

Consider mounting height when planning foradjacent set-on and freestanding storage forproper alignment.

SET-ON OVERHEAD STORAGE WITH STANCHIONSOverhead stanchions are specified as “U”(defacing) stanchions or “O” (non-defacing)stanchions.

“U” stanchions must be mounted through theworksurface (defacing).

“O” stanchions are attached to the worksurfacewith double sided tape (non-defacing).

SET-ON OVERHEAD STORAGE/HIGHBACKSOverhead storage and bookcase units are sized in6" increments.

All WaveWorks and Epic set-on overhead storagemay be used on any properly supportedWaveWorks or Epic worksurface configuration andany credenza or Renegade shell, with theexception of table desks or glass top desks.

Consider worksurface grommet locations whenplanning for set-on overhead storage. Twostorage units side-by-side may interfere with acenter grommet on a worksurface.

Highback units sitting on built-up credenzas with20 inch or less deep worksurfaces require supportpedestals. End panels are not acceptable.

PROPER SUPPORTAn end panel, support panel, or support pedestalmust be located under the end panels of thestorage unit for proper support.

Match unit width to worksurface width or use asupport panel below the end panel of the storageunit or bookcase.

Side panel of set-on surface storage must bewithin 6" of undersurface support/leg.

Set-on surface storage cannot be used in tabledesk application.

Undersurface support rails will not provide propersupport for set-on storage. Support panels arerequired when the unsupported span is greaterthan 48 inches, not an undersurface support rail.

WALL REQUIREMENTSSTUD WALLSWood studs must be a minimum of 2 x 4’ssecured to the floor and ceiling. Maximum height of 14’.


POURED CONCRETE AND CONCRETE BLOCKAttach with appropriate fasteners for wallmaterial.


ATTACHMENTAll wall mounted overhead storage must befastened directly into studs, poured concrete orconcrete block at a minimum of two locationswith fasteners appropriate for the wall material.

Exhibit upper rail

Exhibit mountWaveWorks or Epicoverhead storage

EXHIBIT MOUNT

WALL MOUNT

Studs, poured concreteor concrete block wall

WaveWorks orEpic overheadstorage

Fastenminimum twolocations

End panel orsupport pedestal


Support panel

End or support panel

Support panel



Support and Load


Epicenter Support (Double Sided)Upper Epicenter frame must be supported on bothsides by WaveWorks or Epic worksurface height orbox/file height undersurface storage, bases or endpanels to support worksurfaces, privacy screens,inserts and work tools. Undersurface storagemust be specified without end panel grommetsor back panel option.

The chart below explains how many universalsupport brackets or bases are needed for the widthof the Epicenter. When a support base is used, auniversal bracket will not be needed in thatlocation.

WORKSURFACE SUPPORTAny depth or length WaveWorks or Epicworksurface may be attached perpendicularlyanywhere along the Epicenter slat wall insert whensupported by worksurface brackets (Keeping inmind user’s kneespace area).

All surfaces must be properly supported at theopposite end by a support pedestal, support baseor end panel.


An undersurface support rail may be specified forsurface spans longer than 48" on 13⁄16" thickworksurfaces or 60" on 19⁄16" thick worksurfaces.

Consider additional support where heavy loads areanticipated.

OVERHEAD STORAGE SUPPORTAny length Epicenter overhead storage maystraddle the top of the Epicenter frame whenproperly supported by undersurface storage.

OTHER SUPPORT ISSUESBecause Epicenter may be specified with powerand data capabilities, it will support a power polefor power entry whip. Power pole must be securelyattached at the ceiling and to the top of theEpicenter frame.

Epicenter slat wall inserts will support anycombinations of National work tools and one slatmount monitor arm every 24".

Width ofEpicenter

Number of BracketSets Needed forDouble Sided

Number of BracketSets Needed for

Single Sided

24" – 48" 2 sets 1 set

54" – 96" 3 sets 2 sets

UpperEpicenterframe

Support pedestal, supportbase, end panel, or a metalsupport base

Worksurfacebrackets

Epicenterframe

Slat wallinsert

WaveWorks or Epicundersurface storage

Anywhere along slat wall insert

Slat wall insert supports work tools

Undersurfacesupport rail


Epicenteroverheadstorage

Anywhere along top ofEpicenter frame

Privacy screen

Anywhere along top ofEpicenter trim cap


Support and Load


Epicenter Support (Double Sided, continued)

Epicenter 6" high baseor end panel

Epicenter double depth baseor double depth end panel

Epicenter base orend panel

Epicenter 6" high baseor end panel

Mid support privacy panel

End support privacy panel


Support and Load


Epicenter Support (Single Sided)Epicenter single sided frame must consist of anUpper Epicenter and a Lower Epicenter to createthe single sided application. Single sided must besupported on one side by WaveWorks/Epicworksurface height or box/file height undersurfacestorage, bases or end panels to supportworksurfaces, privacy screens, inserts and worktools. Undersurface storage must be specifiedwithout end panel grommets or back paneloption.

The chart below explains how many universalsupport brackets or bases are needed for the widthof the Epicenter. When a support base is used, auniversal bracket will not be needed in thatlocation.

WORKSURFACE SUPPORTAny depth or length WaveWorks or Epicworksurface may be attached perpendicularlyanywhere along the Epicenter slat wall insert whensupported by worksurface brackets (Keeping inmind user’s kneespace area).

All surfaces must be properly supported at theopposite end by a support pedestal, support baseor end panel.


An undersurface support rail may be specified forsurface spans longer than 48" on 13⁄16" thickworksurfaces or 60" on 19⁄16" thick worksurfaces.


OVERHEAD STORAGE SUPPORTAny length Epicenter single sided overhead storagemay be mounted to the top of the Epicenter framewhen properly supported by undersurface storage.

OTHER SUPPORT ISSUESBecause Epicenter may be specified with powerand data capabilities, it will support a power polefor power entry whip. Power pole must be securelyattached at the ceiling and to the top of theEpicenter frame.

Epicenter slat wall inserts will support anycombinations of National work tools and one slatmount monitor arm every 24".

Width ofEpicenter

Number of BracketSets Needed forDouble Sided

Number of BracketSets Needed for

Single Sided

24" – 48" 2 sets 1 set

54" – 96" 3 sets 2 sets

UpperEpicenterframe

Support pedestal, supportbase, end panel, or a metalsupport base

Worksurfacebrackets

End trim

Upper and LowerEpicenter frame

Slat wallinsert


Anywhere along slat wall insert

Slat wall insert supports work tools

Undersurfacesupport rail



End trim


Privacy screen

Anywhere along top ofEpicenter trim cap


Support and Load


Epicenter Support (Single Sided, continued)

Epicenter base orend panel

End trim

Modesty panelinsert Epicenter 6" high base

or end panel

Modesty panelinsert

End cap

UndersurfacestorageUndersurfacestorage

Modesty panelinsert

End trim

End supportprivacy panel

Modesty panelinsert

Mid supportprivacy panel


Support and Load


Renegade SupportFollow these guidelines when planning forRenegade shells.

CONFIGURATION TYPESShellFreestanding“L” Shaped return or box/file height support“U” Shaped

REQUIRED SUPPORT11⁄8" and 13⁄16" thick.Require support panel every 48".


Surface support is required wherever to surfacesmeet end-to-end.

Freestanding

U” Shape

“L” Return “L” Box/File

Shell

13⁄16" thick surface

48" maximum

Supportrequired


Support and Load


Renegade SupportFollow these guidelines when planning foroverhead and set-on storage components.

PROPER SUPPORT

WALL MOUNTEDRenegade overhead storage components may beattached at desired height directly to loadbearing walls constructed of wood or metal studs,poured concrete or concrete block walls withfasteners appropriate to the wall material.

Consider mounting height when planning foradjacent set-on and freestanding storage forproper alignment.

SET-ON OVERHEAD STORAGE/HIGHBACKSOverhead storage and bookcase units are sized in6" increments.

All Renegade, WaveWorks and Epic set-on overheadstorage may be used on any properly supportedRenegade shell configuration or credenza.

Consider grommet locations when planning forset-on overhead storage. Two storage units side-by-side may interfere with a center grommeton a worksurface.

Highback units sitting on built-up credenzas with20 inch or less deep worksurfaces require supportpedestals. End panels are not acceptable.

PROPER SUPPORTA shell end panel or support pedestal must belocated under the end panels of the storage unitfor proper support. Undersurface support rails willnot provide proper support.

Match unit width to shell width or be certain anend panel or support pedestal is located below theend panel of the storage unit or bookcase.

Side panel of set-on surface storage must bewithin 6" of undersurface support/leg.

Set-on surface storage cannot be used in tabledesk application.

Undersurface support rails will not provide propersupport for set-on storage. Support panels arerequired when the unsupported span is greaterthan 48 inches, not an undersurface support rail.

WALL REQUIREMENTSSTUD WALLSWood studs must be a minimum of 2 x 4’ssecured to the floor and ceiling.Maximum height of 14’.


POURED CONCRETE AND CONCRETE BLOCKAttach with appropriate fasteners for wallmaterial.


ATTACHMENTWall mounted overhead storage must be fasteneddirectly into studs, poured concrete or concreteblock at a minimum of two locations withfasteners appropriate for the wall material.

WALL MOUNT

Studs, poured concreteor concrete block wall

Renegadeoverheadstorage

Fastenminimum twolocations

End panel orsupport pedestal May straddle bridge or return




Power and Data

4-NOF_PowerData 4/21/14 12:34 PM Page 45

Power and Data


Exhibit Power and DataExhibit vertical cable manager conceals androutes task light cords to the integrated wiremanagers available on WaveWorks and Epicworksurfaces. Vertical

cablemanager

Worksurfacewire manager

Multiple belowsurface cablemanagementoptions available

Surface heightpower/data access

Round orracetrackgrommets

Multiple undersurface power/data options available

WaveWorks and

Epic Pedestal Grommet

Renegade Pedestal

Grommet

WaveWorks, Epic and RenegadePower and DataWorksurface wire managers may be specified onWaveWorks and Epic worksurfaces to route cablesbelow the surface.

WORKSURFACE CABLE MANAGEMENTUse any undersurface cable manager to managecables below the worksurface on WaveWorks, Epicor Renegade worksurfaces.

Grommets may be specified for WaveWorks, Epicor Renegade worksurfaces to route cablesthrough the worksurface. Multiple locations maybe specified.

All WaveWorks and Epic undersurface storageinclude an optional grommet at the rear, uppercorner.

Renegade shells include an optional grommet atthe rear, upper corner. Undersurface storageincludes a grommet at the rear, upper corner.

WORKSURFACE POWER AND DATA ACCESS

UNDERSURFACEConvenience outlets, power andpower/communication outlets and Powerlogicsystems may be attached below any WaveWorksor Epic worksurface to provide access to powerand data.

Cables may be routed through the worksurfacewire manager or surface grommet for accessbelow the surface.

SURFACE HEIGHTPower/Data centers, power towers, ByrneInterlink systems and pivoting power grommetsmay be specified within any WaveWorks or Epicworksurface to provide access to power and dataat the surface.

Consider location of support pedestals or otherbelow surface storage when planning for surfaceheight power/data components.

Vertical wire managersare flexible to accommodateuser needs; used to conceal power in-feedand data cables

Horizontal wire manager used to conceal powerin-feed and data cables


Power and Data


WaveWorks, Epic and RenegadePower and Data (continued)

POWERLOGIC INTERCOUPLER SYSTEM WAVEWORKS AND EPICFor private office and open plan applications.Single circuit system plugs directly into buildingpower and attaches below worksurface providinglinked power accessed through surface grommetsbelow.

Provides from 2 to 8 outlet modules.

For use with racetrack grommets in WaveWorksand Epic.

BYRNE INTERLINK SYSTEM WAVEWORKS AND EPICFor private office and open plan applications.Sequential daisy-chain, single circuit systemplugs directly into building power and attachesthrough the worksurface providing linked poweraccessed at surface height.


For use with racetrack grommets in WaveWorksand Epic.

BYRNE INTERLINK IQ SYSTEMWAVEWORKS, EPIC AND RENEGADENon-sequential daisy-chain, single circuit systemplugs directly into building power and connectsto pivoting power grommets within worksurfaceproviding linked power accessed at surfaceheight. For private office, open plan and trainingtable applications.


For use with G17 cutout in WaveWorks, Epic andRenegade.

BYRNE INTERLINK IQ SYSTEM EXAMPLES

Interlink IQ pivotingpower grommet providespower/data access

To building power

Bypass jumperBypass jumper

TABLES

To building power

BYRNE INTERLINK SYSTEM EXAMPLESSurface heightpower/data access

PedestalNo interlink system

To building power


PedestalNo interlink system

To building power

OR...

Bypass jumper


Power and Data


Epicenter Power and DataUpper Epicenter frames can provide 5 wire/3 circuit, 20 amp power to a linear run of workspaces. Frames also provide routing for datacables.

Access to power and data may be above or belowworksurface height depending on the height ofthe WaveWorks or Epic undersurface storage it isattached to.

POWER ENTRY WHIPTwo power entry whips are available. 72" and144" long.

Power entry whip has a modular connector atone end, attached to a flexible metal conduitwith exposed wiring at the other end which ishardwired to the building power.

FROM THE FLOORPower entry whip is hardwired to electrical boxwithin the floor or to a floor monument.

Data cables may also be routed up from the floorto the data channel at the top of the frame.

FROM THE WALL OR COLUMNPower entry whip is hardwired to electrical boxwithin the wall or column.

Data cables may also be routed up from a wall orcolumn to the data channel at the top of theframe.

FROM THE CEILINGPower entry whip is hardwired to electrical boxwithin the ceiling and routed down through apower pole attached to the top of the Epicenterframe.

Data cables may also be routed down throughthe power pole to the data channel at the top ofthe frame.

CABLE ROUTINGPower entry whip and data cables are routed upto the frame behind the undersurface storage ordown through the power pole.

HARDWIRE KITHardwire kit can be used with the non-poweredUpper Epicenter frame.

CIRCUIT ARRANGEMENT

Hot 1

Neutral

I II III

Black

Ground

Hot 2

Hot 3

White

Green/Bare

Red

Blue

Power harness

Epicenterpowered frame

Data cablechannel

Box/File heightundersurface storage

Surface heightundersurface storage

Worksurface heightUpper Epicenterpowered frame

Upper Epicenternon-poweredframe

Box/File heightsingle sidedtackable insert

Surface heightsingle sidedtackable insert

Worksurface heightUpper Epicenterpowered frame

Upper Epicenternon-poweredframe

Hardwire kit


Power and Data


Epicenter Power and Data(continued)

CONNECTION

POWER ENTRY WHIPThe power entry whip 3-way connector plugs intothe power harness within any Epicenter powereddivider frame. Power entry whip may connect atthe end of a run or anywhere within the run,providing power in one or both directions.

JUMPERThe jumper plugs into the power harness withinone Epicenter powered divider frame and plugsinto the next Epicenter powered divider frame tocontinue power along the run.

BYPASS JUMPERThe bypass jumper plugs into the power harnesswithin one Epicenter powered divider frame,passes through a non-powered divider frame orbelow a freestanding component and plugs intothe next powered frame to continue power alongthe run.

EPICENTER POWER AND DATA

ACCESSDuplex receptacles plug into one or both sides ofthe power harness within the Epicenter poweredframe.

Receptacles are labeled as to the specific circuitthey are connected to. I, II, and III.

30" through 72" accept 2 per side. 24" accepts 1 per side.

INSERT CUTOUT OPTIONSTack board and slat/tack board inserts areavailable with multiple cutout options.

Cutouts are always located 9" in from the leftand right end of the insert, with the exceptionof 24" which has a single cutout on center.Cutouts accommodate 1 duplex receptacle or 1 duplex receptacle and 2 blank data ports.

Appropriate faceplates are shipped with theinserts.

INSERT CUTOUT CONFIGURATIONS• No cutouts• 2 power receptacles• 1 power receptacle left, 1 power/data

receptacle right• 1 power receptacle right, 1 power/data

receptacle left• 2 power/data receptacles

Power entry whip from the floor

Power entry whip from wallor column

Power entry whip fromthe ceiling

Power pole

Bypass jumperthrough Epicenter

Powerharness

Bypass jumperbeneath storage

Power direction

Power direction

Jumper

Duplex

Power harness

III

III

Duplex

Duplex

Data ports

No cutouts

Receptaclecutouts

Receptacle left,receptacle/dataright

Receptacle right,receptacle/dataleft

Receptacle/datacutouts

Circuit label

Power Receptacle

Power/Data Receptacle

Duplex Faceplate

Duplex/Data Faceplate




Product Specification

5-NOF_ProductSpecification 4/21/14 12:34 PM Page 51

Product Specification–Exhibit


Exhibit Wall Rails

BASICSAttach to fixed walls to support WaveWorks andEpic worksurfaces, WaveWorks and Epic overheadstorage and Exhibit inserts.

Included based on model ordered:• 1 or 2 rails• Splice plates for rail alignment• 1 or 2 faceplates to conceal fasteners and

splice plates and secure inserts• 72" or 144" long. May be field cut to

length

REQUIREDAppropriate fasteners for wall material. Suppliedby installer.

SPECIFICATION TIPSMinimum rail length is 18". There is no maximumlength requirements for Exhibit rail runs.

Use one rail, with or without faceplate forsupporting worksurfaces or overhead storage.

When mounting overheads, rail must equal or begreater than the width of overheads beingmounted.

Use 2 rails and faceplates when supportinginserts.

Rails can mount at any height when supportinginserts with overheads only.

Specify insert heights based on adjacentcomponent heights; see diagram below.

WORKS WITH• Worksurface mounting brackets for

WaveWorks and Epic worksurfaces• WaveWorks and Epic overhead storage• Exhibit slat wall, tack board, marker board,

organizer shelf and slat wall/tack insertswith trim channels

• Full end trim• Single rail end caps

Use one rail, any lengthWaveWorks or Epicoverhead storage

Upperrail

Faceplate

Lowerrail

Faceplate

Filler striprequired

WaveWorks or Epicoverhead storage

WaveWorks or Epicworksurface

Exhibit inserts




STANDARD HEIGHTS

COUNTER HEIGHTS

BAR HEIGHTS

34" high inserts. Matches66" high vertical storage.



49" high inserts. Matches80" high vertical storage.Also standard height forconference, training roomsand common areas.


28½"

63¾"

28½"

661⁄16"

28½"

66½"

28½"28½"

777⁄8" 785⁄16"

34" high inserts. 36" high inserts. 37" high inserts. 49" high inserts.48" high inserts.

3413⁄16"

701⁄16"

3413⁄16"

723⁄8"

3413⁄16"

7213⁄16"

3413⁄16"3413⁄16"

843⁄16" 845⁄8"

34" high inserts. 36" high inserts. 37" high inserts. 49" high inserts.48" high inserts.

411⁄8"

763⁄8"

411⁄8"

7811⁄16"

411⁄8"

791⁄8"

411⁄8"411⁄8"

90½" 9015⁄16"




Inserts

BASICSTack board, marker board, organizer shelf, slatwall and slat/tack wall inserts attach withinExhibit upper and lower rails with faceplates.

• 2 trim channels each (provided with insert)• 18" to 60" wide. Tack boards and HPL

marker boards may be scribed in the field• 5 heights available on all inserts

REQUIREDExhibit upper and lower rails with faceplates.

Additional trim channels may be ordered forinserts scribed in the field.

Full end trim for inserts at the end of a runwhen end is exposed.

SPECIFICATION TIPSInserts may be used in rails at any desiredheight.

Specify insert height based on adjacentcomponent heights.

For the best aesthetics, specify insert widths tomatch overhead storage and/or worksurfacewidth or depth. Knife rim on worksurface adds 1½" per side to worksurface depth. Specify insert1 size wider than worksurface depth and fieldscribe to match.

FYIPorcelain marker boards, organizer shelf and slatwall inserts may not be field scribed.

It is not required that inserts be placed behindfreestanding storage when wall rails pass behind.

WORKS WITH• Vertical cable manager• Slat wall and slat/tack wall accepts

accessories and work tools anywhere alongthe slat insert.

Upperrail

Faceplate

Lowerrail

Faceplate

Insert

Tack

Slat

Tack board18"-60" wide34", 36", 37",48", 49" high

Marker board24"-60" wide34", 36", 37",48", 49" high

Slat wall24"-48" wide34", 36", 37",48", 49" high

Slat/Tack wall24"-48" wide34", 36", 37", 48", 49" high

23" standard

Organizer shelf36"-60" wide34", 36", 37",48", 49" high

Exhibit inserts

Adjacent storage

Full end trim

Trim channel

Accessories and work tools




Worksurface Mounting Brackets

BASICSAttach anywhere along the Exhibit lower rail tosupport worksurfaces.

REQUIRED• Exhibit lower rails.• Support pedestal, support base, end panel,

metal support base and/or a undersurfacesupport rail.

FYIWall rail faceplates are only required wheninserts are used.

SPECIFICATION TIPSWorksurfaces may attach linear or perpendicularto the lower rail.

• For worksurfaces up to 48" use 2 brackets• For worksurfaces up to 72" use 3 brackets• For worksurfaces greater than 72" use

4 brackets

WORKS WITHWaveWorks or Epic worksurfaces.

Perpendicular

Linear

Lower rail

Worksurfacemountingbrackets

Mounting brackets

Anywhere




Work Tools and Trim

Work Tools

BASICSWork tools attach anywhere along the slat wallor slat/tack wall inserts attached within Exhibitupper and lower rails with faceplates.

REQUIREDSlat wall or slat/tack wall inserts within Exhibitupper and lower wall rails with faceplates.

SPECIFICATION TIPSConsider quantity and types of work tools basedon size of slat wall or slat/tack wall insert.

Consider clearance at worksurface and belowoverhead storage for access to work tools andcontents.

Monitor arms are not recommended to use withslat inserts.

Monitor Arms

BASICSMust properly install slat wall when using amonitor arm.

Recommended to not use monitor arm on theupper four slats of a full slat wall and slat wallcombo insert.

SPECIFICATION TIPSWeight capacity 13 lbs.

One monitor arm every 24" on slat wall and onlyone monitor arm recommended for a slat/tackcombo insert.

Vertical Cable Manager

BASICSVertical cable manager attaches to the trimchannel to conceal and route task light cords.

Clearanceabove

Attach anywhere

Clearancebelow

Full End Trim

BASICSEnd trim finishes the full height end of a run ofwall rails, faceplates and inserts when end isexposed.

SPECIFICATION TIPSEnd trim is 3" higher than insert height. Specifyheight to match insert and wall rail combinedheight.

Wall rail andfaceplate

End trim

Insert

Trim Channels

BASICSFabric or painted trim channels finish the spacebetween inserts. 2 trim channels standard withinserts.

SPECIFICATION TIPSMatch trim channel height to insert height.Match trim channel to insert finish or material ormix finish or materials to create verticalpatterns.

Specify additional trim channels for all fieldscribed inserts.

Verticalcablemanager

Trimchannel

Filler Strips

BASICSFiller strips are required between the wall andExhibit mounted overhead storage to provideproper support where no inserts are used.

WORKS WITHWaveWorks and Epic overhead storage.

Filler strips

Single End Cap

BASICSSingle end cap finishes the end of a single upperor lower wall rail.

SPECIFICATION TIPSUse at the end of an upper or lower wall railwhere no inserts are used.

Single end cap

WORKS WITHVertical cable manager.

Trim channel

Insert



Product Specification–WaveWorks and Epic

Worksurfaces

BASICSWorksurfaces, cornice tops and Epicenter depthworksurfaces may be used to create privateoffice, open plan and table desk configurations.

Worksurfaces may be applied to undersurfacestorage and lateral files to create credenzas ordesks.

Component worksurfaces may also be used toexpand assembled configurations.

Modified worksurface sizing is available. Seeprice list for models available.

9 rim options available on WaveWorks.

2 rim options available on Epic.

Includes appropriate attachment hardware whenspecified.

WaveWorks Worksurfaces• 13⁄16" or 19⁄16" thick• 18" deep: 30" to 96" wide in 6" increments• 24" deep: 30" to 96" wide in 6" increments• 30" deep: 48" to 96" wide in 6" increments• 36" deep: 60" to 84" wide

Epic Worksurfaces• 13⁄16" thick• 18" deep: 30" to 96" wide in 6" increments• 24" deep: 30" to 96" wide in 6" increments• 30" deep: 48" to 96" wide in 6" increments• 36" deep: 60" to 84" wide

Epicenter Depth Worksurfaces• 227⁄16" and 285⁄8" deep. 30" to 96" wide

in 6" increments

Cornice Tops• 13⁄16" or 19⁄16" thick• 15" deep: 18", 30" to 108" wide in

6" increments• 24" deep: 18" and 36" wide

Worksurfaces Wire ManagersA selection of worksurfaces are available withoptional wire managers on 1 end only or 1 or 2 sides. Surface grommets may be located left orright side and on center back. Use worksurfacewire manager fillers to cap off exposed ends ofwire managers.

Worksurfaces

Any combination ofundersurface storage may beused to create a credenza

TablesCredenzas

Epicenter depth worksurfaces

Cornice tops

Box/File height undersurface storage withoutthe end panel grommet or back panel option


1 side 1 or 2 sides 1 or 2 sides

Back onlyLeft onlyRight onlyBack and leftBack and right

Left onlyRight onlyLeft and right


Worksurfaces 24", 30" and36" deep

REQUIREDExhibit lower wall rails and worksurfacemounting brackets, support panels, supportpedestals or undersurface storage components.

SPECIFICATION TIPSProperly supported, worksurfaces may be used inany desired length to create freestanding, tabledesk, linear, peninsula,“L”, “T” and “U”configurations.

By specifying M, E or F in the model number, allworksurfaces arrive with the appropriatebracketry for installation.

M = MainE = ExtensionF = Filler

M = 0 Connecting Flat BracketsE = 2 Connecting Flat BracketsF = 4 Connecting Flat Brackets

Worksurfaces may be configured at box/fileheight combined with worksurface height usingbox/file height and worksurface heightundersurface storage and supports.

For 6" guest side overhang, use 30" deepworksurface with 24" undersurface storage or 36" deep worksurface with 30" undersurfacestorage.

WORKS WITH• Powerlogic Intercoupler system • Byrne Interlink and Interlink IQ electrical

systems• Worksurface grommets• Worksurface wire managers• Undersurface cable management

components• Set-on overhead storage• Privacy screens and modesty panels• Center drawers, keyboard trays, CPU holders

and monitor arms

FYIKnife rim adds 1½" per side to worksurfacedepth. Knife rim is not recommended on lowerstorage as it affects user’s kneespace.

Consider where you specify a worksurface withWorksurface wire manager. When attached toExhibit lower wall rail, do not use at the end ofrun for a cleaner aesthetic, or cap off exposedend with a filler cap.



Freestanding andtable desks

“L” configuration Linear or peninsula“T” configuration

“U” configuration

6" overhang

30" or 36" deepworksurface

24" or 30" deepundersurface storage orsupport

Box/File height

Worksurfaceheight

Or...

Anywhere

Worksurfacewire managerNo worksurfacewire manageror use filler capKnife rim

adds 1½"per side

M

M

EEE

EE

M

F

M




Worksurfaces 18" deep

REQUIREDMetal lateral file and hinged door units.

SPECIFICATION TIPSUse to finish top of metal lateral file and hingeddoor units.

18" surfaces are ideal for training tables.

Cornice tops 15" deep15" deep tops to finish the top of highbackorganizers, Exhibit or wall mount overheadstorage units or bookcases.

REQUIREDHighback organizers, Exhibit or wall mountoverhead storage units, bookcases, or verticalstorage units.

SPECIFICATION TIPSSpecify rim option to match or contrastworksurface rim.

May be used to span 2 units. Specify model withfinished bottom.

Epicenter Depth SurfacesEpic worksurfaces are sized to finish the top ofundersurface storage in Epicenter work spaces.

WaveWorks worksurfaces must be specified at amodified depth of 227⁄16" and 285⁄8 to align withthe Epicenter.

REQUIREDUndersurface storage

SPECIFICATION TIPSUse to finish the top of box/file or worksurfaceheight undersurface storage. When usingWaveWorks worksurface specify 13⁄16" thickworksurface.

Single worksurface may span multipleundersurface storage units.

Match worksurface width to total length ofundersurface storage.

Worksurfaces are available with wire managers.Specify on back edge only.

WORKS WITH• Worksurface grommets• Worksurface wire managers• Undersurface cable management

components



Worksurface height undersurface storagewithout the end panel grommet or back panel option

18" worksurface

Any metal lateral fileand hinged door units




Square or roundsupport bases

Column legswith or withoutdual wheellocking casters

“H” or ”U” stylesupport bases

4-star basesT-legs C-legs

TablesWorksurfaces may be used to create leg-based tableapplications.

Bases available in worksurface height, counterheight, bar height and height adjustable.

All static bases have adjustable glides with a 1½" range.

Mobile bases have dual wheel locking casters.

Bases include appropriate attachment hardware.

REQUIRED FOR PENINSULA CONFIGURATIONSSquare or round support base, column leg, wood halfround support base, “H” or “U” style support base,“C” or “T” leg or 4-star base.




Surface support is required wherever 2 surfaces meetend-to-end.

In place of end panels, corner surfaces may besupported by a support base at the back corner whenconnected to an adjacent surface.

SPECIFICATION TIPSTables may be used in private office, extensions toopen plan environments, conference and trainingareas.

Use mobile tables in collaborative environments asshared worksurfaces.

Tables may be combined in multiple configuration forconference and training areas.

FYIMaximum span between legs on 13⁄16" thickworksurface is 48". Maximum span between legs on19⁄16" thick worksurface is 60".

Support base “H” and “U” Style may be used with allworksurfaces except “U” and “P” shape.


systems• Worksurface grommets• Undersurface cable management components• Privacy screens and mesh, resin and metal

modesty panels• Center drawers, keyboard trays and monitor

arms

“H” style bar or counterheight support bases

“U” style bar or counterheight support bases

Disc bases

Manual Hand Crank Adjustable Height Bases Electrically Adjustable Height Bases

Manual Hand Crank Adjustable Height L Top Bases Electrically Adjustable Height L Top Bases




Modesty and Back Panels

BASICSModesty panels may be applied to all componentworksurfaces, tables and undersurface storagecomponents to finish the back or createkneespace on approach side.

Modesty panels are non-structural and provideprivacy/aesthetics.

Back panels may be applied to all undersurfacestorage components to finish the back.

Includes appropriate attachment hardware.

Modesty Panels• Full overlay in 28" worksurface height and

22" box/file height.• 1/3 height in 8" and 13" heights.

Back Panels• In 28" worksurface height and 22" box/file

height.

REQUIREDWorksurface, table, pedestal or lateral file.

Full overlay

Single or double pedestal

Worksurface height or box/file height

1/3 height

Full overlay

Pedestal or lateral files

Provides accessto power anddata at thewall

Worksurface Support

BASICSA selection of worksurface supports and basesare available to create desking configurationsand tables to fit most desired aesthetics.

All static supports and bases have adjustableglides with a 1½" range.

Mobile bases have dual wheel locking casters.

Bases include appropriate attachment hardware.

Supports• 12", 24", 30" and 36" deep• Worksurface and box/file heights

Bases• Worksurface, counter, bar height and height

adjustable.

SPECIFICATION TIPSFor an open aesthetic use “U” Style or “H” Stylesupport bases.

For stronger look and where consistent finishesare desired, use undersurface storagecomponents and end panels.

Surface heights may be varied by using box/fileheight end panels.

Recommended work surface length of 84" onangled top when using lower height storage toallow for sufficient kneespace.

“H” Style or “U” Stylesupport base

Square or roundsupport base

Undersurface supportand end panels

Box/File endsupport

Bar height Counter height

Square or roundsupport base

Inset on guest side

Rectangular

Worksurface height or box/file height

1/3 height




SPECIFICATION TIPSModesty PanelsModesty panels may be inset to provide guestside knee space.

Full overlay. Specify modesty panel to matchworksurface width.

Consider worksurface and undersurface storagecomponent height and widths as well as supportlocations when specifying modesty panel widths.

By specifying, M, E or F in the model number, allmodesty panels arrive with the appropriatebracketry for installation.

M = Main E = Extension F = Filler

Full HeightM = 0 BracketsE = 1 Return Mounting BracketF = 2 Return Mounting Brackets

1/3 HeightM = 2 L-BracketsE = 1 L-Bracket/1 Return Mounting BracketF = 2 Return Mounting Brackets

Main Modesty Panels• Specify modesty panel as MAIN when using

as a full modesty or back panel• Specify back panel to match pedestal

height and width.

Filler Modesty Panels• Specify modesty panel as FILLER when

attaching to two component end panels

Extension Modesty Panels• Specify modesty panel as EXTENSION when

attaching to one component side

Main 1/3 Height Modesty Panels• Specify 1/3 height modesty panel as

MAIN when attaching between twopedestals, a pedestal and end panel ortwo end panels

Filler 1/3 Height Modesty Panels• Specify 1/3 height modesty panel as

FILLER when attaching to two end panels

Extension 1/3 Height Modesty Panels• Specify 1/3 height modesty panel as

EXTENSION when attaching to a pedestaland end panel or end panel to end panel

1/3 height. Specify modesty panel to matchworksurface width minus width of undersurfacestorage components.

FYIGlass top desk accepts modesty panel betweenpedestals only.

Back PanelMain Modesty Panel Filler Modesty PanelExtension Modesty Panel

Main 1/3 Height Modesty Panels

Filler 1/3 Height Modesty Panel

Extension 1/3 Height Modesty Panel

Support base or end panel

Undersurface storage

Tapered




Privacy Screens

BASICSPrivacy screens are freestanding and can be seton component worksurfaces, tables andundersurface storage worksurfaces to add seatedprivacy.

Includes appropriate hardware.

Privacy Screens Set-On Surface• Acrylic tapered or rectangular and felt

rectangular• 18" high.• 21", 24", 27", 30", 36", 42", 48", 54", 60"

and 72" wide.

Privacy Screens Edge Mount Modesty/Privacy• Rectangular• 32" high.• 21", 24", 27", 30", 36", 42", 48", 54", 60"

and 72" wide.

Privacy Screens Edge Mount Privacy• Rectangular or tapered• 20" high.• 21", 24", 27", 30", 36", 42", 48", 54", 60"

and 72" wide.

SPECIFICATION TIPSMay be used to provide degree of enclosure or todefine personal space.

Placed on box/file height storage and onworksurface to create a layered division of space.Mix tapered and rectangular to vary theaesthetic.

Consider worksurface width and location ofadjacent or overhead storage when specifyinglength.

Multiple screen lengths may be used along a runto vary the look.

Rectangular

Rectangular

Tapered

Edge mount modesty/privacy screen

Edge mountprivacy screen



Tapered privacyscreen Epicentermount




Storage

BASICSOverhead storage components are available aswall mounted or Exhibit mounted. Additionalstorage components can be freestanding, set-onsurface or used as undersurface storage.

All undersurface and freestanding componentshave adjustable glides with a 1½" range.

Wall mount and set-on components includeappropriate attachment hardware.

Exhibit mount cabinets include appropriateattachment hardware but wall rails must beordered separately.

Multiple pull options are available.

TYPESUndersurface StorageWorksurface height

• File/file and box/box/file pedestals. • Lateral files, double door units, bookcase,

mixed storage and multi-file cabinets.Box/file height

• Box/file pedestals.• Box/file mobile pedestals.• Lateral files, and bookcases.

Set-On Storage• Highback organizers with or without doors.• Corner highback organizers with or without

doors.• Bookcases.• Bookcase with doors.• Storage module shelf.

Exhibit Wall Rail or Wall Mount• Overhead storage cabinets with or without

doors.

Freestanding Storage• Mobile pedestals.• 2, 3, 4 and 5 drawer lateral files with

13⁄16" or 19⁄16" top. • Multi-file and mixed storage cabinet. with

13⁄16" or 19⁄16" top.• Storage towers and wardrobe/storage

cabinets doors, drawers and bookcases. • Bookcases.• Bookcases with doors.

Undersurface Storage Set-On Storage

Exhibit or Wall Mount Overhead Storage

Freestanding Storage

90 degreebookcase optionavailable




Storage (continued)

REQUIREDWorksurface for undersurface component storage.

Ganging brackets for Exhibit mounted, wallmounted overhead storage or runs offreestanding components.

SPECIFICATION TIPSUse Exhibit or wall mount overhead to utilizewall space in private office and collaborativeenvironments around the perimeter space.

Set-on storage may be used to create work spaceprivacy when placed back to back. Considerlocation of worksurface grommets when selectingoverhead storage.

Consider freestanding storage componentsheights when used adjacent to Exhibit wall railor wall mounted overhead storage.

Overhead stanchions are specified as “U”(defacing) stanchions or “O” (non-defacing)stanchions.

“U” stanchions must be mounted to theworksurface (defacing).

“O” stanchions are attached to the worksurfacewith double sided tape (non-defacing).

Multiple undersurface storage components maybe placed under a common worksurface within aworkspace. Specify combined undersurfacestorage component widths and depths to matchworksurface.

Add a cushion to undersurface top or use amobile pedestal with a cushion top for additionalseating.

Multiple 3 drawer lateral files may be gangedtogether under a common worksurface to create a counter height workcenter.

Vary the height of long runs of freestandingstorage to compensate for uneven floors, whileproviding visual interest.

WORKS WITH• Full overlay modesty panels for pedestals

and lateral files• Worksurface for undersurface storage• Task lights for highback organizers, Exhibit

or wall mount overhead storage• Interior drawer accessories for box, file and

lateral file drawers• Interior accessories for open storage• Storage surface cushion• Tack board

Specify ganging plates foreach joint to create a clean,straight run

Back-to-backfor maximumprivacy

Accepts tackboard

Specify height to match

Undersurface storagecomponents with a singlecommon worksurface top

Add a cushion

Common worksurface top

Creates a workcenter

Vary component height

End or support panel

Support panel


Product Specification–Epicenter


Use any width and combination of undersurfacecomponents on either side to create small back-to-back or long runs of multiple workspaces.

Worksurfaces are not dependent upon theundersurface component widths used as long asthe combined total widths are equal. Specify anylength worksurface available to finish the tops ofthe undersurface storage.

Epicenter divider and insert lengths are notdependent on the undersurface componentwidths, as long as the combined widths are equalto the total width of the undersurfacecomponents. Consider desired location of insertsand power/data locations when planning for runlength.

Consider the degree of privacy desired. 7" of divider height may be gained by usingworksurface height versus box/file heightundersurface storage.

Freestanding storage or components with set-onstorage may be used between runs to createadditional work space privacy and visual interest.

Small work spaces 7" higher than box/file height


Multiple runs of work spaces

Any combinationof divider lengths

Box/file height undersurface storage withoutthe end panel grommet or back panel option

Undersurface Storage (Double and Single Sided)

BASICSEpic or WaveWorks worksurface or box/file heightundersurface storage components are placedback-to-back to create the infrastructure ofEpicenter work spaces.

Undersurface storage supports the Epicenterframe dividers in any length run.

Undersurface storage components haveadjustable glides with a 1½" range.


TYPESWorksurface Height

• File/file and box/box/file pedestals. 23" and 29" deep

• Lateral files, double door units, bookcase,mixed storage, project drawer and multi-file cabinets. 23" deep. 24", 30" and36" wide

Box/File Height• Box/file pedestals. 23" deep• Lateral files, box/lateral files, bookcases,

project drawer and double door units. 23"deep. 24", 30" and 36" wide

REQUIREDEpic or WaveWorks worksurfaces.

Epicenter end trim.

SPECIFICATION TIPSEpic or WaveWorks worksurface storagecomponents are used to create any length run of collaborative work spaces. Due to the base styles unique to Epic and WaveWorks, it is recommended that one style be usedconsistently within a run.

FYISpecify undersurface storage without the endpanel grommet or back panel option.

WaveWorks worksurfaces must be specified with amodified depth of 227⁄16" or 285⁄8" to align withthe Epicenter.

WORKS WITH• Epic or WaveWorks worksurfaces• Epicenter dividers• Interior drawer accessories for box, file and

lateral file drawers• Storage surface cushion

Multiple runs of work spaces

Any combination of divider lengths

End trim

Box/file height undersurface storage withoutthe end panel grommet or back panel option




Epicenter (Double and Single Sided)

BASICSEpicenter dividers are a series of powered andnon-powered frames that are supported by Epicand WaveWorks worksurface height and box/fileheight undersurface storage, bases or endpanels.

TYPESUpper Epicenter Powered

• Frame with power harness. 13" high. 24"-72" in 6" increments. 24" provides 1 power/data location per side. 30"-72"provide 2 per side

Non-powered • Frame only. 13" high. 24"-96" in

6" increments

Lower EpicenterNon-powered (only)

• Frame only. 22" (box/file height) and 28" (worksurface height) high. 24"-96" in6" increments

• Must be specified in same width as UpperEpicenter

REQUIREDEpic or WaveWorks back-to-back undersurfacestorage, bases or end panels for double sided.

Upper and Lower Epicenter for single sidedapplication.

Undersurface storage, bases or end panels and aworksurface must be used on one side of thesingle sided Epicenter.

Universal attachment brackets.

Tack board, marker board, slat wall and slat/tackboard inserts.

The chart below explains how many universalsupport brackets or bases are needed for thewidth of the Epicenter. When a support base isused, a universal bracket will not be needed inthat location.

Width of Epicenter Number of Brackets/Bases

24" – 48" 254" – 66" 472" – 96" 6

SPECIFICATION TIPSEpicenters may be used in any combination oflengths along the run.

Epicenter divider lengths are not dependent onthe undersurface component widths, as long asthe combined widths are equal to the totalwidth of the run.

Consider desired location of power/data accesswhen planning for location of powered and non-powered dividers.

Non-powered Epicenter DividersNon-powered dividers may be used as a supportfor perpendicular worksurfaces, privacy screensand work tools. Specify slat wall inserts whereverworksurfaces and work tools will be placed.

Powered Epicenter DividersPowered dividers provide power/data capabilitiesanywhere along the run and also supportperpendicular worksurfaces, privacy screens andwork tools wherever slat wall inserts are specified.

Receptacles are specified separately.

FYIWhen a privacy screen is used above a divider,an Epicenter trim cap is required.

Inserts are not dependent upon the frame lengthand may be placed off module with theexception of where power data must be accessed.Specify inserts with power/data cutouts to matchdivider length to align cutouts to receptacles.

WORKS WITH• Power entry whip, jumpers and bypass

jumpers• Epicenter end trim and trim caps• Tack board, marker board, slat wall and

slat/tack board• Privacy screen• Work tools

Powered Epicenter

Non-powered Epicenter

Power/Data accessabove the worksurface


Power harness

Epicenterpowered frame

Data cablechannel


Power/Data accessbelow the worksurface





Epicenter (Double and Single Sided, continued)

Powered Epicenter

Non-powered Epicenter

Power/Data accessabove the worksurface

End trim

Modesty panelinsert

Worksurface height undersurface storage without the end panel grommet or back panel option


Power/Data accessbelow the worksurface

Divider trim cap required


End trim

Upper andLower Epicenter




Epicenter Dividers Power and Data

BASICSEpicenter powered dividers contain a powerharness within the frame to provide 3 circuit/5 wire, 20 amp power to a linear run of workstations and a top channel for routingdata cables.

Power harness is pre-installed within the dividerframe.

TYPE• Frame with power harness. 13" high.

24"-72" in 6" increments. 24" provides 1 power/data location per side. 30"-72"provide 2 per side

REQUIREDPower entry whipPower pole for ceiling access to buildingpower jumperBypass jumperReceptacle or power/data receptacleTack board or slat/tack board inserts

SPECIFICATION TIPSPower entry whipSpecify power entry whip to bring power to thepower harness. Power entry may be locatedanywhere along the run and will provide powerto all connected harness’s in either direction.

Plan for power entry whip to be located as closeto building power as possible.

Power poleSpecify a power pole to if closest building poweris in the ceiling.

Power entry whip must be specified separately.

JumperPower is continued from divider to divider byspecifying an 18" jumper for each dividerconnection.

Bypass jumperPower and data may pass through a non-powereddivider or below freestanding storage byspecifying a bypass jumper.

ReceptaclesReceptacles plug directly into the power harnesswithin the Epicenter divider frame.

Specify duplex receptacles for each cutout intack board or slat/tack board inserts specified.Faceplates will be specified when specifyinginserts.

Receptacles are labeled as to the specific circuitthey are connected to. I, II, and III.

Specify receptacles based on the device to beconnected. For example, computers should be ona separate circuit than lighting or other devicesthat may require a greater load.

Power entry whip from floor, wall or column Power entry whip from the ceiling

Power pole

Jumper Bypass jumperthrough Epicenter

Power direction

Duplex receptacle

Data cables route through top channel

III

IIIDuplex Faceplate

Duplex/Data FaceplateDuplex

Duplex

Data ports

Circuit label

Power Receptacle

Power/Data Receptacle

.59" (15 mm)

.76" (19.5 mm)

Epicenter withModel Epicenter Bypass Epicenter with box/file worksurface heightJumpers height pedestals pedestals

25N42ELJ 24" Epicenter - -25N48ELJ 30" Epicenter - -25N54ELJ 36" Epicenter - -25N60ELJ 42" Epicenter - -25N66ELJ 48" Epicenter - -25N72ELJ 54" Epicenter - -25N78ELJ 60" Epicenter - -

25N84ELJ 66" Epicenter 1 - 18" W Vertical -Storage Cabinet

25N90ELJ 72" Epicenter 1 - 24" W Storage -Cabinet

25N96ELJ 78" Epicenter 1 - 30" W Vertical 1 - 18" W Vertical Storage Cabinet Storage Cabinet

25N102ELJ 84" Epicenter 1 - 36" W Vertical 1 - 24" W Vertical Storage Cabinet Storage Cabinet

- 2 - 18" W Vertical -Storage Cabinets

25N108ELJ 90" Epicenter - 1 - 30" W Vertical Storage Cabinet

25N114ELJ 96" Epicenter 2 - 24" W Vertical 1 - 36" W Vertical Storage Cabinets Storage Cabinet

- - 2 - 18" W Vertical Storage Cabinets

25N126ELJ - - 2 - 24" W VerticalStorage Cabinets

Bypass Jumper Applicability




Inserts

BASICSInserts attach to Epicenter dividers to finish theframe, provide and support work tools, supportworksurfaces, receptacles and power/datareceptacles.

Marker board, slat wall and slat/tack insertsinclude two trim channels.

If tack board or slat/tack board is specified withpower/data cutouts, they include appropriatefaceplates.

Appropriate attachment hardware included.

TYPESTack board, marker board, slat wall and slat/tackboard for Upper Epicenter

• 11" high. 24"-72" in 6" increments

Tack board, laminate, and veneer for singlesided Epicenter

• 39" (worksurface height) high. 24"-72" in6" increments

• 32" (box/file height) high. 24"-72" in 6" increments

Veneer and laminate modesty panel inserts• 26" (worksurface height) high. 24"-72" in

6" increments. Modified sizing available• 19" (box/file height) high. 24"-72" in

6" increments. Modified sizing available

REQUIREDUpper Epicenter divider frame for double sided application

Upper and Lower Epicenter divider frame for single sided application

SPECIFICATION TIPSInserts are not dependent upon the frame lengthand may be placed off module with the exceptionof where power data must be accessed. Specifytack board and slat/tack board inserts withpower/data cutouts to match divider length.

Upper inserts are needed for a double sidedUpper Epicenter application or on the user sideof a single sided application.

Single sided inserts are needed for a single sidedapplication on the approach side.

Modesty panel insert sizing must be specifiedafter the undersurface storage or Epicentersupports are specified. Modesty panel inserts willrun between undersurface storage and endsupport panels. Modesty panel inserts run behindEpicenter support bases. Modified sizingavailable.

Work tools are available to attach anywherealong the slat insert.

INSERT CUTOUT OPTIONSTack board and slat/tack board inserts areavailable with multiple cutout options.

Slat/Tack board insertwith or without cutouts

Slat/Tack board insertwith or without cutouts

Slat wall insert

No cutouts

Power receptaclecutouts

Power receptacle left,power/data receptacleright

Receptacle right,power/data receptacleleft

Power/data receptacle cutouts

Work tools

Cutouts are always located 9" in from the leftand right end of the insert, with the exceptionof 24" which has a single cutout on center.

Cutouts accommodate 1 duplex receptacle or 1 duplex receptacle and 2 blank data ports.

INSERT CUTOUT CONFIGURATIONS• No cutouts• 2 power receptacles

• 1 power receptacle left, 1 power/datareceptacle right

• 1 power receptacle right, 1 power/datareceptacle left

• 2 power/data receptacles

WORKS WITH• Receptacles and power/data receptacles• Work tools

Epicenter modestypanel insert availablein modified sizing




Overhead Storage

BASICSEpicenter overhead storage straddles theEpicenter divider and provides an increaseddegree of privacy. Because overhead supportsrest on the worksurface, they may be placed inline with or extend beyond the divider.

Sliding door models feature a facemountpowder coated aluminum track along top andbottom of cabinet.

TYPESShared:1 open shelf or sliding door on each side.

Individual:2 open shelves or sliding doors on 1 side.

• 14" high. 15" deep. 30", 36", 42", 48" and60" wide

Single sided:2 open shelves or sliding doors on 1 side.

• 14" high. 15" deep. 30", 36", 42", 48" and60" wide

REQUIREDEpic or WaveWorks worksurfaces and undersurfacestorage.

SPECIFICATION TIPSPlace any quantity of Epicenter overhead storageunits along the run.

Use any width or combination widths. The onlymaximum is dictated by the run length.

Not recommended to gang overheads spanningmore than two surfaces.

FYIShort overhead supports are required whenoverhead will be placed on a worksurfacehanging off slat inserts. Long overhead supportsare required in all other applications.

Single sided Epicenter overheads have anunfinished back. An overhead back panel mustbe specified separately when using the overheadin an open plan.

Consider clearance of overhead when specifyingwork tools.

Individual Shared

Anywhere along the run

2 short and 2 longoverhead supports shown here due to placement of overhead



End trim



Worksurfaces

BASICSEpic and WaveWorks worksurfaces may be usedto create Epicenter open plan configurations.

Modified worksurface sizing is available.

Includes all appropriate attachment hardware.

9 rim options available on WaveWorks.

2 rim options available on Epic.

Epic and WaveWorks worksurfaces• 13⁄16" or 19⁄16" thick• 18" deep. 30" to 96" wide

in 6" increments• 24" deep. 30" to 96" wide



in 6" increments

Epicenter depth surfaces• 13⁄16" thick• Softened rim profile 227⁄16" or 285⁄8" deep.

30" to 96" wide in 6" increments• Knife rim profile 237⁄8" or 30" deep. 30" to

96" wide in 6" increments

Worksurfaces Wire ManagersA selection of worksurfaces are available withwire managers on 1 end only or 1 or 2 sides.Surface grommets may be located left or rightside and on center back.

REQUIREDEpicenter worksurface mounting brackets.

Epicenter support base, support panels, supportpedestals and undersurface storage components.

SPECIFICATION TIPSReturn worksurfaces attached anywhere along theEpicenter slat wall insert with worksurfacemounting brackets may be used in any desireddepth or width.

For undersurface storage, specify worksurfacedepth and width to match undersurface storagecomponents.

WaveWorks worksurfaces must be specified with amodified depth of 227⁄16" or 285⁄8" to align withthe Epicenter when used on undersurface storagecomponents.


1 end 1 or 2 sides 1 or 2 sides

Back onlyLeft onlyRight onlyBack and leftBack and right

Left onlyRight onlyLeft and right

Undersurface storagecomponents

Standard depthworksurfaces

Epicenter depthworksurfaces

Support

Epicenter worksurfacemounting brackets


WORKS WITH• Epic or WaveWorks worksurfaces• Epicenter worksurface mounting brackets• Epicenter worksurfaces• Powerlogic Intercoupler system • Byrne Interlink and Interlink IQ electrical

systems• Worksurface grommets• Undersurface cable management

components• Privacy screens and modesty panels• Center drawers, keyboard trays and monitor

arms• Storage surface cushion on undersurface

storage worksurface top






Work Tools and Accessories

Privacy Screen

BASICSProvides seated privacy at the top of theEpicenter trim cap.


Specify length to match divider length.• 24"-72" wide in 6" increments

Ability to attach privacy screen to mid and endsupport panels.

Trim Cap

BASICS

Finishes the top of the Epicenter divider.• 24"-144" wide in 6" increments

Field scribe to desired size.

Work ToolsA wide selection of work tools may be specifiedto attach anywhere along the slat wall.

Consider items to be stored and their heightwhen planning for work tool quantities.

End Trim

BASICS

Finishes the end of the Epicenter divider at theend of a run.

• 11" End Trim – Use at the end of a doublesided Epicenter when a worksurface is putat the end of a run without an Epicenter.

• 12" End Trim – Use at the end of a run fora double sided Epicenter.

• 21" End Trim – Use at the end of a run fora single sided Epicenter, box/file height,when only the bottom of the Epicenter isat the end of a run.

• 27" End Trim – Use at the end of a run fora single sided Epicenter, worksurfaceheight, when only the bottom of theEpicenter is at the end of a run.

• 33" End Trim – Use at the end of a singlesided Epicenter, box/file height.

• 39" End Trim – Use at the end of a singlesided Epicenter, worksurface height.

End Trim Filler

BASICS

Fills the space between undersurface storage.• 22", 31" and 37" high

Flexible Monitor Arms

• Not recommended for use under overheads• One monitor arm every 24"


Product Specification–Renegade


Shells

BASICSRenegade may be planned and specified usingassembled or component shells to createfreestanding desks and credenzas for privateoffice, collaborative and open plan environments.Renegade or WaveWorks undersurface storagecomponents may be added to complete theconfiguration.

Linkable shells may be added to expandconfigurations.

Linkable shells include appropriate attachmenthardware.

Shells include modesty panels.

11⁄8" or 13⁄16" thick worksurface in soft rim.

Include leveling glides with 1½" adjustmentrange.

TYPESShells

• Worksurface height with full end panel. 24"or 30" deep. 36"-48" and 60"-72" wide in 6" increments

• Box/File height with full end panel. 21" or24" deep. 60"-72" wide in 6" increments

• 1 worksurface height full end panel and 1 box/file height end panel. 21" or 24"deep. 60"-72" wide in 6" increments

Linkable shells• Worksurface height with 1 full end panel

and 1 narrow end panel. 21" or 24" deep.30"-48" and 60"-72" wide in 6" increments

• Worksurface height with 2 narrow endpanels. 21" or 24" deep. 36"-48" and 60"-72" wide in 6" increments

Credenza shells• Worksurface and box/file height with full

end panels. 21" or 24" deep. 74" and 110"wide

SUPPORTRenegade shells are self supporting. Linkableshells with narrow end panels are properlysupported when attached to full end panelshells.

FYIA support panel is required when knee space isgreater than 48"

Credenza shells are required when filling with storage.

SPECIFICATION TIPSShells and linkable shells may be used in anydesired length to create freestanding, linear,peninsula,“L”, “T” and “U” configurations.

Shells may be configured at box/file heightcombined with worksurface height.

Shells and linkable shells may be linked togetherin-line or back-to-back to create collaborativeenvironments.

Shells will accept any combination of Renegade,WaveWorks or Epic set-on overhead storage tocreate private office or open plan environmentswith a high degree of enclosure.


systems • Worksurface grommets• Undersurface cable management

components• Renegade, WaveWorks or Epic set-on

overhead storage • Privacy screens and modesty panels• Center drawers, keyboard trays and monitor

arms

Freestanding “L” configuration

Linear or peninsula“T” configuration

“U” configuration

Assembled Desks and Credenzas

May be specified withsuspended box/file or fullheight pedestals

Shells and Credenza Shells

Greater than 48"

Support panelrequired

Any combination of Renegade orWaveWorks undersurface storage

Box/Fileheight shell Worksurface

height shellRenegade WaveWorks or Epic set-on overhead storage




Storage

BASICSRenegade storage components are available inwall mount overhead storage, set-on storagecomponent, freestanding and undersurfacestorage components to fit within shells andcredenzas.

All freestanding components have adjustableglides with a 1½" range.

Wall mount and set-on components includeappropriate attachment hardware.


All available with locks.

TYPESShell undersurface storageWorksurface height

• File/File and box/box/file pedestals. 20",23" and 29" deep

• Lateral files, double door units, bookcase,mixed storage and multi-file cabinets. 20" and 23" deep. 36" wide

Box/File height• Box/File pedestals. 20", 23" and 29" deep• Lateral files, and bookcases. 20" and

23" deep. 36" wide

Set-on storage• Highback organizers with or without doors.

38" high. 15" deep. 48" and 60"-72" widein 6" increments

• Corner highback organizers without doors.38" high. 15" deep. 36", 42", 66" or 72" wide

• Bookcases with or without doors. 14" deep.36" wide. 38" high

Wall mount• Overhead storage cabinets with or without

doors. 18" high. 15" deep. 30"-48" wide in 6" increments

Freestanding storage• 2, 3, and 4 drawer lateral files. 21" or

24" deep. 36" wide• Component tops for 3 and 4 drawer lateral

files. 11⁄8" or 13⁄16" thick. 21" or 24" deep. 72" or 108" wide.

• Double door unit. 21" or 24" deep. 29" high. 36" wide

• Multi-file and mixed storage cabinet. 21" or 24" deep. 29" high. 36" wide

• Storage towers and wardrobe/storagecabinets doors, drawers and bookcases. 21" or 24" deep. 67" high. 24" and 36" wide

• Bookcases. 14" deep. 41", 53", and 67" high. 36" wide

• Box/File mobile pedestals, with or withoutcushion top

Undersurface storage

Set-on storage

Wall mount overhead storage

Freestanding storage

90 degreebookcase optionavailable




Storage (continued)

SPECIFICATION TIPSWall mount overhead storage to utilize wall space in private office and collaborativeenvironments around the perimeter space.

Set-on storage may be used to create work spaceprivacy when placed back to back. Considerlocation of worksurface grommets when selectingoverhead storage.

Consider freestanding storage componentsheights when used adjacent to mountedoverhead storage.

Multiple undersurface storage components maybe placed within a shell.

Add a cushion to shell top or use a pedestal witha cushion top for additional seating.

3 lateral files may be ganged together under acommon component top to create a counterheight workcenter.

Vary the height of long runs of freestandingstorage to compensate for uneven floors, whileproviding visual interest.

Ganging bracket available for undersurfacestorage to provide a clean aesthetic.

When creating a storage credenza, must specifyshell in 74" or 110" to accommodateundersurface storage.

WORKS WITH• Shells and linkable shells• Task lights for highback organizers• Interior drawer accessories for box, file and

lateral file drawers• Interior accessories for open storage• Storage surface cushion• Tack board, marker board and slat wall for

highback organizers

Back-to-backfor maximumprivacy

Accepts tackboard, markerboard or slatwall

Specify height to match

Multiple undersurface storagecomponents within a singlecommon shell

Add a cushion

Component top

Creates a workcenter

Vary component height


Product Specification–WaveWorks, Renegade and Epic


Cable Management

BASICSMultiple cable managers and covers are availableto manage and route cables below theworksurface vertically and horizontally.

Wire ManagersIncludes appropriate attachment hardware.

Vertical Wire Managers attach to the underside ofthe worksurface.

SPECIFICATION TIPSUse cable managers and covers to route andmanage cables below the worksurface from theworksurface top to the power/data source.

Multiple cable managers may be used below theworksurfaces and to manage cable from oneworksurface to the next.

Consider location of undersurface storage,supports and worksurface grommets andpower/data components when planning for cablemanager type and length.

May also be used below ganged tables to managecables from one table to the next.


To buildingpower/data

Undersurfacewire manager

May spanworksurfaces

To buildingpower/data

Vertical wire managersroute cables down table leg

Vertical wire managersare flexible to accommodateuser needs; used to conceal power in-feedand data cables

Horizontal wire manager used to conceal powerin-feed and data cables




-Work Tools and AccessoriesVertical Pigeon Hole StorageBASICSDesigned to fit below highback organizer toprovide easy access to small items and papers.

• Vertical pigeon hole storage. 3 fixedshelves

FYIMay interfere with tack board, when placedbelow highback organizer. Specify shorter widthtack board to allow unit to fit flush against backof organizer.

Organizing StackerBASICSProvides an accessory shelf anywhere within ahighback organizer overhead storage orbookcase.

• 1 shelf• 13" deep. 32" to 41" wide. 5" high

Storage Surface CushionBASICSProvides guest seating on box/file heightundersurface storage top.

Specify size to match worksurface size.

Tack Boards, Marker Boardsand Slat WallsBASICSMarker boards and slat wall may be wallattached. Tack boards may be wall attached orattached within highback organizer.

When specifying tack board, refer to the tackboard applicability charts in the Casegoods Book2 Price List.

Slat wall will support work tools.

Task LightsBASICSMount below storage on highback organizer orbelow overhead storage.Task Light

• 5" deep. 23" or 47" wide. 2" high LED tasklight

LED task light• 3½" deep. 22", 28" or 34" wide. 1½" high.

Can daisy chain up to 3LED strip light (magnetic)

• 1" deep. 16", 25", or 31" wide. 1" high.Can daisy chain up to 3.

Center Drawers and Keyboard TraysBASICSMount kneespace or clear area below workspace.

Consider width and depth of worksurface whenspecifying.

Metal Storage CubbyBASICSProvides an accessory shelf anywhere below anEpic 13" high overhead storage cabinet.

• 1 shelf• 13" deep. 30" to 48" wide. 5" high




Work ToolsA wide selection of work tools may be specifiedto attach anywhere along the slat wall.

Consider items to be stored and their heightwhen planning for work tool quantities

Flexible Monitor Arms -Grommet and ClampAttach to worksurface through grommet mountor clamp mount.

Consider interference with other componentsabove and behind monitor arm when specifyinglocation on the worksurface.

Not recommended for use with knife edgeworksurfaces, flip/nest training tables or a topthat is utilizing any metal base.

When there is a worksurface overhang (Ex: 24"D pedestal with a 30"D worksurface), itis recommended that a customer use a grommetmount monitor arm versus a clamp mountmonitor arm.

Not recommended to turn the monitor arms awayfrom the user side.

Privacy ScreenBASICSPrivacy Screens may be applied to componentworksurfaces, tables and undersurface storageworksurfaces to add seated privacy.


Privacy Screens Set-On Surface• Acrylic tapered or rectangular and felt

rectangular• 18" high.• 21", 24", 27", 30", 36", 42", 48", 54", 60"

and 72" wide.

Privacy Screens Edge Mount Modesty/Privacy• Rectangular• 32" high.• 21", 24", 27", 30", 36", 42", 48", 54", 60"

and 72" wide.

Privacy Screens Edge Mount Privacy• Rectangular or tapered• 20" high.• 21", 24", 27", 30", 36", 42", 48", 54", 60"

and 72" wide.

Edge mount modesty/privacy screen

Edge mountprivacy screen



Tapered privacyscreen Epicentermount


Notes



SpecificationGuide

Epicenter®

Epic® Casegoods

Exhibit™ Wall Rail Solution

Renegade™ Casegoods

WaveWorks® Casegoods

Specification Guide



www.NationalOfficeFurniture.com

1205 Kimball Boulevard, Jasper, IN 47549800.482.1717 Fax 812.482.8800

©Kimball International, Inc. 2014Printed in the USAForm No. NSPEC Ver. 14A Unit of Kimball International

NPGC Specification Guide Cover_Ver 14_Layout 1 5/1/14 12:02 PM Page 1

Documents

Specification Guide Specification Guide