Upload
mahnoor
View
214
Download
0
Embed Size (px)
DESCRIPTION
Technical Data Of Optical Fiber Ground Wire.
Citation preview
7/18/2019 Specific Facilities Data for Opgw Updated
http://slidepdf.com/reader/full/specific-facilities-data-for-opgw-updated 1/2
SPECIFIC FACILITIES DATA FOR OPGW
(OPGW cable construction shall comply with IEEE-1138-2009 and IEC Publication 1396)
Sr. No. Information Required Data to be supplied by the Manufacturer
1 Optic Fiber Ground Wire (OPGW)
a) Maker’s Name & Address ZTT & China Nantong
b) Origin of OPGW China
c) Nominal cross sectional area (mm2) 71.2
d) Center stainless steel tube (No./Dia.) 1(Aluminum tube)/7.5mm
e) Aluminum clad steel wires (No./Dia.) 13/2.25mm
f) Lay direction–outer layer Right
g) Overall diameter (mm) 12.0
h) Calculated breaking load (kgf) 7408
i) Approximate total mass (kg/km) 425
j) Electrical resistance at 20℃ 0.773Ω/km
k) Modulus of elasticity (N/mm2) 132900
l) Coefficient of linear expansion 14.2×10-6
/℃
m) Short circuit current capacity at 20℃ 39.9kA2S
n) Everyday tension at 32℃, no wind 1482 kgf (for reference)
o) Max. tension at 32℃, wind pressure 135kg/m2 2963 kgf (for reference)
p) Sag at 0℃ and no wind (span=400m) 2872 mm(for reference)
2 Optical Fiber
a) Optical fiber type Single mode confirming to G. 652
b) Number of fibers≥24 24
c) Core diameter 8.5 ± 0.7 um
d) Cladding diameter 125 ± 0.7μm
e) Wavelength 1310nm/1550nm
f) Mode field diameter 9.2 ± 0.4μm (1310nm)
10.4 ± 0. 8μm (1550nm)
g) Cut-off wavelength ≤ 1260 nm
h) Method of jointing fiber in field The method of jointing fiber is Fusion Method.Theory of fusion method is to use high-voltage
to discharge, produce arc, so that the partial
end of fiber be melted, then achieve the goal.
i) Maximum loss at joint ≤ 0.1
j) Maximum end connector loss ≤ 0.5
k) Maximum attenuation (db/km)
- at 1310nm ≤0.36
- at 1550nm ≤0.22
l) Maximum dispersion at 1310nm ≤3.5 ps/nm·km
m) Maximum dispersion at 1550nm ≤18 ps/nm·km
7/18/2019 Specific Facilities Data for Opgw Updated
http://slidepdf.com/reader/full/specific-facilities-data-for-opgw-updated 2/2
n) Mode field dia. at 1310nm & 1550nm 9.2 ± 0.4μm (1310nm)
10.4 ± 0. 8μm (1550nm)
o) Zero dispersion wavelength (nm) 1300~1324
p) Zero dispersion slope (ps/nm2.km) ≤ 0.092
q) Attenuation coefficient 1310nm ≤ 0.36dB/kmr) Attenuation coefficient 1550nm ≤ 0.22 dB/km
s) Cladding Non-circularity (%) ≤ 1.0
t) Coating diameter 243 ± 5μm
u) Coating-cladding concentricity ≤ 6μm
v) Temperature dependence -60℃ to +85℃ (The temperature range which
optical fiber can bear.)
3 Packing
a) Maximum reel length (≥5000m) Maximum reel length: 5000m
Nominal length: 3200m
b) Reel marking
- Identification Yes
- Length & Segment Yes
- Destination address Yes
- Inspection stamp & date Yes
4 Test Report
Bidder is instructed to provide a recent type/routine
test report for the above mentioned OPGW cable
We can provide the type test report which is the
same type as the constructure.