316E L Hydraulic Excavator

Engine Drive

Engine Model Catreg C44 ACERTtrade Maximum Travel Speed 52 kmh 32 mph

Engine Power ndash ISO 14396 89 kW 119 hp Maximum Drawbar Pull 1562 kN 35115 lbf

Weights

Minimum Operating Weight 17 200 kg 37920 lb

Maximum Operating Weight 17 800 kg 39242 lb

316E L Hydraulic Excavator Specifications

Engine Swing Mechanism

Engine Model Cat C44 ACERT Swing Speed 93 rpm

Engine Power ndash ISO 14396 89 kW 119 hp Swing Torque 447 kNmiddotm 32969 lbf-ft

Bore 105 mm 413 in Service Refill CapacitiesStroke 127 mm 500 in

Displacement 44 L 269 in3 Fuel Tank Capacity 290 L 7661 gal

Cooling System 24 L 634 galWeights Engine Oil (with filter) 135 L 357 gal

Minimum Operating Weight 17 200 kg 37920 lb Swing Drive (each) 24 L 063 gal

Maximum Operating Weight 17 800 kg 39242 lb Final Drive (each) 5 L 132 gal

Long Undercarriage 51 m (169) reach boom R225m (75) Hydraulic System (including tank) 190 L 5019 gal stick 28 mt (309 t) counterweight 076 m3 (0994 yd3) bucket Hydraulic Tank 106 L 2800 gal 500 mm (20) TG shoes

Long Undercarriage 51 m (169) reach boom R29m (96) Track stick 28 mt (309 t) counterweight 076 m3 (0994 yd3) bucket 700 mm (28) TG shoes Number of Shoes (each side) 44 pieces

Number of Track Rollers (each side) 7 piecesHydraulic System Number of Carrier Rollers (each side) 2 pieces

Main System ndash Maximum Flow 2 times 150 2 times 40 Sound Performance(Total) Lmin galmin

Maximum Pressure ndash Equipment 35 000 kPa 5076 psi ISO 6396 Maximum Pressure ndash Travel 35 000 kPa 5076 psi Operator Sound 71 dB(A) Maximum Pressure ndash Swing 22 600 kPa 3278 psi ISO 6395 Pilot System ndash Maximum Flow 258 Lmin 1574 in3min Spectator Sound 101 dB(A) Pilot System ndash Maximum Pressure 4120 kPa 598 psi bull Operator Sound ndash The operator sound level is measured according Boom Cylinder ndash Bore 110 mm 4 in to the procedures specified in ISO 63941998 for cab offered by Boom Cylinder ndash Stroke 1193 mm 47 in Caterpillar when properly installed and maintained and tested

with doors and windows closed Stick Cylinder ndash Bore 120 mm 5 in bull Exterior Sound ndash The labeled spectator sound power level is

Stick Cylinder ndash Stroke 1331 mm 52 in measured according to the test procedures and conditions specifi ed Bucket Cylinder ndash Bore 110 mm 4 in in 200414EC Bucket Cylinder ndash Stroke 1039 mm 41 in bull Hearing protection may be needed when operating with an open

operator station and cab (when not properly maintained for doors windows open) for extended periods or in a noisy environment Drive

Maximum Travel Speed 52 kmh 32 mph Standards Maximum Drawbar Pull 1562 kN 35115 lbf

Brakes ISO 10265 2008

ROPS Cab ISO 12117-2

CabOPG ISO 10262 1998

14

Dimensions All dimensions are approximate

3

9 1

10 6

7 4 5

8 2

Reach Boom

51 m (169)

Stick R29 (96) R26 (86) R225 (74)

1 Shipping Height 3090 mm (102) 3090 mm (102) 3090 mm (102)

Shipping Height at Boom Top 3080 mm (101) 3020 mm (911) 2920 mm (97)

Shipping Height with Guard Rail 3090 mm (102) 3090 mm (102) 3090 mm (102)

Shipping Height with Top Guard 3100 mm (102) 3100 mm (102) 3100 mm (102)

2 Shipping Length 8580 mm (282) 8570 mm (281) 8550 mm (281)

3 Tail Swing Radius 2500 mm (82) 2500 mm (82) 2500 mm (82)

4 Length to Center of Rollers 3170 mm (105) 3170 mm (105) 3170 mm (105)

5 Track Length 3970 mm (130) 3970 mm (130) 3970 mm (130)

6 Ground Clearance 440 mm (15) 440 mm (15) 440 mm (15)

7 Track Gauge 1990 mm (66) 1990 mm (66) 1990 mm (66)

8 Transport Width

500 mm (20) Shoes 2520 mm (83) 2520 mm (83) 2520 mm (83)

600 mm (24) Shoes 2590 mm (86) 2590 mm (86) 2590 mm (86)

700 mm (28) Shoes 2690 mm (810) 2690 mm (810) 2690 mm (810)

9 Cab Height 2890 mm (96) 2890 mm (96) 2890 mm (96)

Cab Height with Top Guard 3100 mm (102) 3100 mm (102) 3100 mm (102)

10 Counterweight Clearance 1010 mm (34) 1010 mm (34) 1010 mm (34)

Bucket Capacity (General Duty) 076 m3 (0994 yd3) 076 m3 (0994 yd3) 076 m3 (0994 yd3)

Bucket Tip Radius 1380 mm (46) 1380 mm (46) 1380 mm (46)

Including shoe lug height

Without shoe lug height

15

316E L Hydraulic Excavator Specifications

Working Ranges All dimensions are approximate

12

Meters

11

10

9

8

7

6

4

5 3 4

3

2

1 5

0

4

3

2

1

1

7

2

6

R26

R29

R225

5

6

7 11 10 9 8 7 6 5 4 3 2 1 0 -1 Meters

Stick

1 Maximum Digging Depth

2 Maximum Reach at Ground Level

3 Maximum Cutting Height

4 Maximum Loading Height

5 Minimum Loading Height

6 Maximum Depth Cut for 2440 mm (80) Level Bottom

7 Maximum Vertical Wall Digging Depth

R29 (96)

6390 mm (210)

8990 mm (296)

8880 mm (292)

6270 mm (207)

2000 mm (67)

6160 mm (203)

4910 mm (161)

Reach Boom 51 m (169)

R26 (86)

6090 mm (200)

8780 mm (2810)

8920 mm (293)

6280 mm (207)

2300 mm (77)

5870 mm (193)

4930 mm (162)

R225 (74)

5740 mm (1811)

8460 mm (279)

8740 mm (288)

6110 mm (201)

2650 mm (88)

5500 mm (181)

4490 mm (149)

16

Operating Weight and Ground Pressure

700 mm (28) 600 mm (24) 500 mm(20) Triple Grouser Shoes Triple Grouser Shoes Triple Grouser Shoes

kg lb kPa psi kg lb kPa psi kg lb kPa psi

Reach Boom ndash 510 m (169)

R29 (96) 17 800 39242 36 522 17 600 38801 42 609 17 300 38140 49 711

R26 (86) 17 700 39022 36 522 17 500 38581 41 595 17 300 38140 49 711

R225 (74) 17 700 39022 36 522 17 500 38581 41 595 17 200 37920 49 711

All weights are rounded up to nearest 100 kg and lb including General Duty 076 m3 (0994 yd3) bucket (610 kg [13448 lb]) Kg and lb were rounded up separately so some of the kg and lb do not match

Actual weight will depend on final machine configuration

Major Component Weights

Base Machine (with boom cylinder without counterweight front linkage and track) 5720 kg 12610 lb

Long Undercarriage 3770 kg 8310 lb

Counterweight ndash 28 mt (309 t) 2800 kg 6170 lb

Boom (includes lines pins and stick cylinder)

Reach Boom ndash 510 m (169) 1320 kg 2910 lb

Stick (includes lines pins bucket cylinder and bucket linkage)

R29 (96) 910 kg 2010 lb

R26 (86) 840 kg 1850 lb

R225 (74) 810 kg 1790 lb

Track Shoe (Longper two tracks)

500 mm (20) Triple Grouser 2190 kg 4830 lb

600 mm (24) Triple Grouser 2420 kg 5340 lb

700 mm (28) Triple Grouser 2650 kg 5840 lb

All weights are round up to nearest 10 kg and lb except for quick coupler and buckets Kg and lb were rounded up separately so some of the kg and lb do not match

Base machine includes 75 kg (165 lb) operator weight 90 fuel weight and undercarriage with center guard

Actual weight will depend on final machine configuration

17

316E L Hydraulic Excavator Specifications

Bucket and Stick Forces

Reach Boom 510 m (169)

Stick R29 (96) R26 (86) R225 (74)

General Duty

Bucket Digging Force (ISO) 111 kN 25000 lb 111 kN 25000 lb 111 kN 25000 lb

Stick Digging Force (ISO) 75 kN 16900 lb 80 kN 18000 lb 88 kN 19800 lb

18

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft

m ft

75 m kg 3950 3950 423 250 ft lb 60 m kg 3400 3400 579 200 ft lb 9600 9600 7500 7500 1875 45 m kg 5000 5000 4600 3250 3250 2750 667 150 ft lb 10850 10850 10000 6950 7200 6050 2177 30 m kg 6250 4700 5000 3100 3350 2400 712 100 ft lb 13450 10150 10750 6700 7300 5250 2334 15 m kg 7450 4400 4850 3000 3550 2300 724 50 ft lb 16100 9500 10450 6400 7850 5000 2376

Ground Line kg 5600 5600 7300 4250 4750 2900 3800 2350 704 lb 12950 12950 15700 9100 10200 6200 8350 5100 2310

ndash15 m kg 6100 6100 10 800 7700 7250 4200 4700 2850 4250 2600 649 ndash 50 ft lb 13600 13600 24600 16550 15550 9000 10150 6150 9350 5700 2125 ndash30 m kg 10 150 7850 7150 4250 5450 3300 548 ndash100 ft lb 21900 16900 15300 9200 12200 7300 1783

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 3250 3250 476 250 ft lb 7500 7500 7300 7300 1509 60 m kg 3500 3300 2850 2850 618 200 ft lb 6450 6450 6350 6350 2005 45 m kg 4600 4600 4300 3300 2750 2550 701 150 ft lb 10000 10000 9400 7000 6100 5600 2289 30 m kg 8850 8750 5900 4800 4800 3150 2800 2250 744 100 ft lb 18850 18850 12650 10300 10450 6750 6200 4950 2439 15 m kg 7200 4450 4900 3000 3400 2150 3000 2150 756 50 ft lb 15550 9600 10500 6400 6600 4700 2480

Ground Line kg 6250 6250 7300 4250 4750 2900 3400 2200 736 lb 14400 14400 15700 9100 10200 6200 7450 4750 2416

ndash15 m kg 5750 5750 10 150 7650 7250 4150 4700 2850 3900 2400 684 ndash 50 ft lb 12800 12800 23100 16400 15500 8950 10100 6100 8650 5250 2240 ndash30 m kg 9950 9950 10 750 7800 7300 4200 4900 2950 589 ndash100 ft lb 22400 22400 23200 16700 15650 9050 10850 6550 1919 ndash45 m kg 7750 7750 5400 4850 423 ndash150 ft lb 16300 16300 11900 11100 1351

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

19

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

316E L Hydraulic Excavator Specifications

Engine Swing Mechanism

Engine Model Cat C44 ACERT Swing Speed 93 rpm

Engine Power ndash ISO 14396 89 kW 119 hp Swing Torque 447 kNmiddotm 32969 lbf-ft

Bore 105 mm 413 in Service Refill CapacitiesStroke 127 mm 500 in

Displacement 44 L 269 in3 Fuel Tank Capacity 290 L 7661 gal

Cooling System 24 L 634 galWeights Engine Oil (with filter) 135 L 357 gal

Minimum Operating Weight 17 200 kg 37920 lb Swing Drive (each) 24 L 063 gal

Maximum Operating Weight 17 800 kg 39242 lb Final Drive (each) 5 L 132 gal

Long Undercarriage 51 m (169) reach boom R225m (75) Hydraulic System (including tank) 190 L 5019 gal stick 28 mt (309 t) counterweight 076 m3 (0994 yd3) bucket Hydraulic Tank 106 L 2800 gal 500 mm (20) TG shoes

Long Undercarriage 51 m (169) reach boom R29m (96) Track stick 28 mt (309 t) counterweight 076 m3 (0994 yd3) bucket 700 mm (28) TG shoes Number of Shoes (each side) 44 pieces

Number of Track Rollers (each side) 7 piecesHydraulic System Number of Carrier Rollers (each side) 2 pieces

Main System ndash Maximum Flow 2 times 150 2 times 40 Sound Performance(Total) Lmin galmin

Maximum Pressure ndash Equipment 35 000 kPa 5076 psi ISO 6396 Maximum Pressure ndash Travel 35 000 kPa 5076 psi Operator Sound 71 dB(A) Maximum Pressure ndash Swing 22 600 kPa 3278 psi ISO 6395 Pilot System ndash Maximum Flow 258 Lmin 1574 in3min Spectator Sound 101 dB(A) Pilot System ndash Maximum Pressure 4120 kPa 598 psi bull Operator Sound ndash The operator sound level is measured according Boom Cylinder ndash Bore 110 mm 4 in to the procedures specified in ISO 63941998 for cab offered by Boom Cylinder ndash Stroke 1193 mm 47 in Caterpillar when properly installed and maintained and tested

with doors and windows closed Stick Cylinder ndash Bore 120 mm 5 in bull Exterior Sound ndash The labeled spectator sound power level is

Stick Cylinder ndash Stroke 1331 mm 52 in measured according to the test procedures and conditions specifi ed Bucket Cylinder ndash Bore 110 mm 4 in in 200414EC Bucket Cylinder ndash Stroke 1039 mm 41 in bull Hearing protection may be needed when operating with an open

operator station and cab (when not properly maintained for doors windows open) for extended periods or in a noisy environment Drive

Maximum Travel Speed 52 kmh 32 mph Standards Maximum Drawbar Pull 1562 kN 35115 lbf

Brakes ISO 10265 2008

ROPS Cab ISO 12117-2

CabOPG ISO 10262 1998

14

Dimensions All dimensions are approximate

3

9 1

10 6

7 4 5

8 2

Reach Boom

51 m (169)

Stick R29 (96) R26 (86) R225 (74)

1 Shipping Height 3090 mm (102) 3090 mm (102) 3090 mm (102)

Shipping Height at Boom Top 3080 mm (101) 3020 mm (911) 2920 mm (97)

Shipping Height with Guard Rail 3090 mm (102) 3090 mm (102) 3090 mm (102)

Shipping Height with Top Guard 3100 mm (102) 3100 mm (102) 3100 mm (102)

2 Shipping Length 8580 mm (282) 8570 mm (281) 8550 mm (281)

3 Tail Swing Radius 2500 mm (82) 2500 mm (82) 2500 mm (82)

4 Length to Center of Rollers 3170 mm (105) 3170 mm (105) 3170 mm (105)

5 Track Length 3970 mm (130) 3970 mm (130) 3970 mm (130)

6 Ground Clearance 440 mm (15) 440 mm (15) 440 mm (15)

7 Track Gauge 1990 mm (66) 1990 mm (66) 1990 mm (66)

8 Transport Width

500 mm (20) Shoes 2520 mm (83) 2520 mm (83) 2520 mm (83)

600 mm (24) Shoes 2590 mm (86) 2590 mm (86) 2590 mm (86)

700 mm (28) Shoes 2690 mm (810) 2690 mm (810) 2690 mm (810)

9 Cab Height 2890 mm (96) 2890 mm (96) 2890 mm (96)

Cab Height with Top Guard 3100 mm (102) 3100 mm (102) 3100 mm (102)

10 Counterweight Clearance 1010 mm (34) 1010 mm (34) 1010 mm (34)

Bucket Capacity (General Duty) 076 m3 (0994 yd3) 076 m3 (0994 yd3) 076 m3 (0994 yd3)

Bucket Tip Radius 1380 mm (46) 1380 mm (46) 1380 mm (46)

Including shoe lug height

Without shoe lug height

15

316E L Hydraulic Excavator Specifications

Working Ranges All dimensions are approximate

12

Meters

11

10

9

8

7

6

4

5 3 4

3

2

1 5

0

4

3

2

1

1

7

2

6

R26

R29

R225

5

6

7 11 10 9 8 7 6 5 4 3 2 1 0 -1 Meters

Stick

1 Maximum Digging Depth

2 Maximum Reach at Ground Level

3 Maximum Cutting Height

4 Maximum Loading Height

5 Minimum Loading Height

6 Maximum Depth Cut for 2440 mm (80) Level Bottom

7 Maximum Vertical Wall Digging Depth

R29 (96)

6390 mm (210)

8990 mm (296)

8880 mm (292)

6270 mm (207)

2000 mm (67)

6160 mm (203)

4910 mm (161)

Reach Boom 51 m (169)

R26 (86)

6090 mm (200)

8780 mm (2810)

8920 mm (293)

6280 mm (207)

2300 mm (77)

5870 mm (193)

4930 mm (162)

R225 (74)

5740 mm (1811)

8460 mm (279)

8740 mm (288)

6110 mm (201)

2650 mm (88)

5500 mm (181)

4490 mm (149)

16

Operating Weight and Ground Pressure

700 mm (28) 600 mm (24) 500 mm(20) Triple Grouser Shoes Triple Grouser Shoes Triple Grouser Shoes

kg lb kPa psi kg lb kPa psi kg lb kPa psi

Reach Boom ndash 510 m (169)

R29 (96) 17 800 39242 36 522 17 600 38801 42 609 17 300 38140 49 711

R26 (86) 17 700 39022 36 522 17 500 38581 41 595 17 300 38140 49 711

R225 (74) 17 700 39022 36 522 17 500 38581 41 595 17 200 37920 49 711

All weights are rounded up to nearest 100 kg and lb including General Duty 076 m3 (0994 yd3) bucket (610 kg [13448 lb]) Kg and lb were rounded up separately so some of the kg and lb do not match

Actual weight will depend on final machine configuration

Major Component Weights

Base Machine (with boom cylinder without counterweight front linkage and track) 5720 kg 12610 lb

Long Undercarriage 3770 kg 8310 lb

Counterweight ndash 28 mt (309 t) 2800 kg 6170 lb

Boom (includes lines pins and stick cylinder)

Reach Boom ndash 510 m (169) 1320 kg 2910 lb

Stick (includes lines pins bucket cylinder and bucket linkage)

R29 (96) 910 kg 2010 lb

R26 (86) 840 kg 1850 lb

R225 (74) 810 kg 1790 lb

Track Shoe (Longper two tracks)

500 mm (20) Triple Grouser 2190 kg 4830 lb

600 mm (24) Triple Grouser 2420 kg 5340 lb

700 mm (28) Triple Grouser 2650 kg 5840 lb

All weights are round up to nearest 10 kg and lb except for quick coupler and buckets Kg and lb were rounded up separately so some of the kg and lb do not match

Base machine includes 75 kg (165 lb) operator weight 90 fuel weight and undercarriage with center guard

Actual weight will depend on final machine configuration

17

316E L Hydraulic Excavator Specifications

Bucket and Stick Forces

Reach Boom 510 m (169)

Stick R29 (96) R26 (86) R225 (74)

General Duty

Bucket Digging Force (ISO) 111 kN 25000 lb 111 kN 25000 lb 111 kN 25000 lb

Stick Digging Force (ISO) 75 kN 16900 lb 80 kN 18000 lb 88 kN 19800 lb

18

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft

m ft

75 m kg 3950 3950 423 250 ft lb 60 m kg 3400 3400 579 200 ft lb 9600 9600 7500 7500 1875 45 m kg 5000 5000 4600 3250 3250 2750 667 150 ft lb 10850 10850 10000 6950 7200 6050 2177 30 m kg 6250 4700 5000 3100 3350 2400 712 100 ft lb 13450 10150 10750 6700 7300 5250 2334 15 m kg 7450 4400 4850 3000 3550 2300 724 50 ft lb 16100 9500 10450 6400 7850 5000 2376

Ground Line kg 5600 5600 7300 4250 4750 2900 3800 2350 704 lb 12950 12950 15700 9100 10200 6200 8350 5100 2310

ndash15 m kg 6100 6100 10 800 7700 7250 4200 4700 2850 4250 2600 649 ndash 50 ft lb 13600 13600 24600 16550 15550 9000 10150 6150 9350 5700 2125 ndash30 m kg 10 150 7850 7150 4250 5450 3300 548 ndash100 ft lb 21900 16900 15300 9200 12200 7300 1783

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 3250 3250 476 250 ft lb 7500 7500 7300 7300 1509 60 m kg 3500 3300 2850 2850 618 200 ft lb 6450 6450 6350 6350 2005 45 m kg 4600 4600 4300 3300 2750 2550 701 150 ft lb 10000 10000 9400 7000 6100 5600 2289 30 m kg 8850 8750 5900 4800 4800 3150 2800 2250 744 100 ft lb 18850 18850 12650 10300 10450 6750 6200 4950 2439 15 m kg 7200 4450 4900 3000 3400 2150 3000 2150 756 50 ft lb 15550 9600 10500 6400 6600 4700 2480

Ground Line kg 6250 6250 7300 4250 4750 2900 3400 2200 736 lb 14400 14400 15700 9100 10200 6200 7450 4750 2416

ndash15 m kg 5750 5750 10 150 7650 7250 4150 4700 2850 3900 2400 684 ndash 50 ft lb 12800 12800 23100 16400 15500 8950 10100 6100 8650 5250 2240 ndash30 m kg 9950 9950 10 750 7800 7300 4200 4900 2950 589 ndash100 ft lb 22400 22400 23200 16700 15650 9050 10850 6550 1919 ndash45 m kg 7750 7750 5400 4850 423 ndash150 ft lb 16300 16300 11900 11100 1351

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

19

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

Dimensions All dimensions are approximate

3

9 1

10 6

7 4 5

8 2

Reach Boom

51 m (169)

Stick R29 (96) R26 (86) R225 (74)

1 Shipping Height 3090 mm (102) 3090 mm (102) 3090 mm (102)

Shipping Height at Boom Top 3080 mm (101) 3020 mm (911) 2920 mm (97)

Shipping Height with Guard Rail 3090 mm (102) 3090 mm (102) 3090 mm (102)

Shipping Height with Top Guard 3100 mm (102) 3100 mm (102) 3100 mm (102)

2 Shipping Length 8580 mm (282) 8570 mm (281) 8550 mm (281)

3 Tail Swing Radius 2500 mm (82) 2500 mm (82) 2500 mm (82)

4 Length to Center of Rollers 3170 mm (105) 3170 mm (105) 3170 mm (105)

5 Track Length 3970 mm (130) 3970 mm (130) 3970 mm (130)

6 Ground Clearance 440 mm (15) 440 mm (15) 440 mm (15)

7 Track Gauge 1990 mm (66) 1990 mm (66) 1990 mm (66)

8 Transport Width

500 mm (20) Shoes 2520 mm (83) 2520 mm (83) 2520 mm (83)

600 mm (24) Shoes 2590 mm (86) 2590 mm (86) 2590 mm (86)

700 mm (28) Shoes 2690 mm (810) 2690 mm (810) 2690 mm (810)

9 Cab Height 2890 mm (96) 2890 mm (96) 2890 mm (96)

Cab Height with Top Guard 3100 mm (102) 3100 mm (102) 3100 mm (102)

10 Counterweight Clearance 1010 mm (34) 1010 mm (34) 1010 mm (34)

Bucket Capacity (General Duty) 076 m3 (0994 yd3) 076 m3 (0994 yd3) 076 m3 (0994 yd3)

Bucket Tip Radius 1380 mm (46) 1380 mm (46) 1380 mm (46)

Including shoe lug height

Without shoe lug height

15

316E L Hydraulic Excavator Specifications

Working Ranges All dimensions are approximate

12

Meters

11

10

9

8

7

6

4

5 3 4

3

2

1 5

0

4

3

2

1

1

7

2

6

R26

R29

R225

5

6

7 11 10 9 8 7 6 5 4 3 2 1 0 -1 Meters

Stick

1 Maximum Digging Depth

2 Maximum Reach at Ground Level

3 Maximum Cutting Height

4 Maximum Loading Height

5 Minimum Loading Height

6 Maximum Depth Cut for 2440 mm (80) Level Bottom

7 Maximum Vertical Wall Digging Depth

R29 (96)

6390 mm (210)

8990 mm (296)

8880 mm (292)

6270 mm (207)

2000 mm (67)

6160 mm (203)

4910 mm (161)

Reach Boom 51 m (169)

R26 (86)

6090 mm (200)

8780 mm (2810)

8920 mm (293)

6280 mm (207)

2300 mm (77)

5870 mm (193)

4930 mm (162)

R225 (74)

5740 mm (1811)

8460 mm (279)

8740 mm (288)

6110 mm (201)

2650 mm (88)

5500 mm (181)

4490 mm (149)

16

Operating Weight and Ground Pressure

700 mm (28) 600 mm (24) 500 mm(20) Triple Grouser Shoes Triple Grouser Shoes Triple Grouser Shoes

kg lb kPa psi kg lb kPa psi kg lb kPa psi

Reach Boom ndash 510 m (169)

R29 (96) 17 800 39242 36 522 17 600 38801 42 609 17 300 38140 49 711

R26 (86) 17 700 39022 36 522 17 500 38581 41 595 17 300 38140 49 711

R225 (74) 17 700 39022 36 522 17 500 38581 41 595 17 200 37920 49 711

All weights are rounded up to nearest 100 kg and lb including General Duty 076 m3 (0994 yd3) bucket (610 kg [13448 lb]) Kg and lb were rounded up separately so some of the kg and lb do not match

Actual weight will depend on final machine configuration

Major Component Weights

Base Machine (with boom cylinder without counterweight front linkage and track) 5720 kg 12610 lb

Long Undercarriage 3770 kg 8310 lb

Counterweight ndash 28 mt (309 t) 2800 kg 6170 lb

Boom (includes lines pins and stick cylinder)

Reach Boom ndash 510 m (169) 1320 kg 2910 lb

Stick (includes lines pins bucket cylinder and bucket linkage)

R29 (96) 910 kg 2010 lb

R26 (86) 840 kg 1850 lb

R225 (74) 810 kg 1790 lb

Track Shoe (Longper two tracks)

500 mm (20) Triple Grouser 2190 kg 4830 lb

600 mm (24) Triple Grouser 2420 kg 5340 lb

700 mm (28) Triple Grouser 2650 kg 5840 lb

All weights are round up to nearest 10 kg and lb except for quick coupler and buckets Kg and lb were rounded up separately so some of the kg and lb do not match

Base machine includes 75 kg (165 lb) operator weight 90 fuel weight and undercarriage with center guard

Actual weight will depend on final machine configuration

17

316E L Hydraulic Excavator Specifications

Bucket and Stick Forces

Reach Boom 510 m (169)

Stick R29 (96) R26 (86) R225 (74)

General Duty

Bucket Digging Force (ISO) 111 kN 25000 lb 111 kN 25000 lb 111 kN 25000 lb

Stick Digging Force (ISO) 75 kN 16900 lb 80 kN 18000 lb 88 kN 19800 lb

18

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft

m ft

75 m kg 3950 3950 423 250 ft lb 60 m kg 3400 3400 579 200 ft lb 9600 9600 7500 7500 1875 45 m kg 5000 5000 4600 3250 3250 2750 667 150 ft lb 10850 10850 10000 6950 7200 6050 2177 30 m kg 6250 4700 5000 3100 3350 2400 712 100 ft lb 13450 10150 10750 6700 7300 5250 2334 15 m kg 7450 4400 4850 3000 3550 2300 724 50 ft lb 16100 9500 10450 6400 7850 5000 2376

Ground Line kg 5600 5600 7300 4250 4750 2900 3800 2350 704 lb 12950 12950 15700 9100 10200 6200 8350 5100 2310

ndash15 m kg 6100 6100 10 800 7700 7250 4200 4700 2850 4250 2600 649 ndash 50 ft lb 13600 13600 24600 16550 15550 9000 10150 6150 9350 5700 2125 ndash30 m kg 10 150 7850 7150 4250 5450 3300 548 ndash100 ft lb 21900 16900 15300 9200 12200 7300 1783

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 3250 3250 476 250 ft lb 7500 7500 7300 7300 1509 60 m kg 3500 3300 2850 2850 618 200 ft lb 6450 6450 6350 6350 2005 45 m kg 4600 4600 4300 3300 2750 2550 701 150 ft lb 10000 10000 9400 7000 6100 5600 2289 30 m kg 8850 8750 5900 4800 4800 3150 2800 2250 744 100 ft lb 18850 18850 12650 10300 10450 6750 6200 4950 2439 15 m kg 7200 4450 4900 3000 3400 2150 3000 2150 756 50 ft lb 15550 9600 10500 6400 6600 4700 2480

Ground Line kg 6250 6250 7300 4250 4750 2900 3400 2200 736 lb 14400 14400 15700 9100 10200 6200 7450 4750 2416

ndash15 m kg 5750 5750 10 150 7650 7250 4150 4700 2850 3900 2400 684 ndash 50 ft lb 12800 12800 23100 16400 15500 8950 10100 6100 8650 5250 2240 ndash30 m kg 9950 9950 10 750 7800 7300 4200 4900 2950 589 ndash100 ft lb 22400 22400 23200 16700 15650 9050 10850 6550 1919 ndash45 m kg 7750 7750 5400 4850 423 ndash150 ft lb 16300 16300 11900 11100 1351

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

19

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

316E L Hydraulic Excavator Specifications

Working Ranges All dimensions are approximate

12

Meters

11

10

9

8

7

6

4

5 3 4

3

2

1 5

0

4

3

2

1

1

7

2

6

R26

R29

R225

5

6

7 11 10 9 8 7 6 5 4 3 2 1 0 -1 Meters

Stick

1 Maximum Digging Depth

2 Maximum Reach at Ground Level

3 Maximum Cutting Height

4 Maximum Loading Height

5 Minimum Loading Height

6 Maximum Depth Cut for 2440 mm (80) Level Bottom

7 Maximum Vertical Wall Digging Depth

R29 (96)

6390 mm (210)

8990 mm (296)

8880 mm (292)

6270 mm (207)

2000 mm (67)

6160 mm (203)

4910 mm (161)

Reach Boom 51 m (169)

R26 (86)

6090 mm (200)

8780 mm (2810)

8920 mm (293)

6280 mm (207)

2300 mm (77)

5870 mm (193)

4930 mm (162)

R225 (74)

5740 mm (1811)

8460 mm (279)

8740 mm (288)

6110 mm (201)

2650 mm (88)

5500 mm (181)

4490 mm (149)

16

Operating Weight and Ground Pressure

700 mm (28) 600 mm (24) 500 mm(20) Triple Grouser Shoes Triple Grouser Shoes Triple Grouser Shoes

kg lb kPa psi kg lb kPa psi kg lb kPa psi

Reach Boom ndash 510 m (169)

R29 (96) 17 800 39242 36 522 17 600 38801 42 609 17 300 38140 49 711

R26 (86) 17 700 39022 36 522 17 500 38581 41 595 17 300 38140 49 711

R225 (74) 17 700 39022 36 522 17 500 38581 41 595 17 200 37920 49 711

All weights are rounded up to nearest 100 kg and lb including General Duty 076 m3 (0994 yd3) bucket (610 kg [13448 lb]) Kg and lb were rounded up separately so some of the kg and lb do not match

Actual weight will depend on final machine configuration

Major Component Weights

Base Machine (with boom cylinder without counterweight front linkage and track) 5720 kg 12610 lb

Long Undercarriage 3770 kg 8310 lb

Counterweight ndash 28 mt (309 t) 2800 kg 6170 lb

Boom (includes lines pins and stick cylinder)

Reach Boom ndash 510 m (169) 1320 kg 2910 lb

Stick (includes lines pins bucket cylinder and bucket linkage)

R29 (96) 910 kg 2010 lb

R26 (86) 840 kg 1850 lb

R225 (74) 810 kg 1790 lb

Track Shoe (Longper two tracks)

500 mm (20) Triple Grouser 2190 kg 4830 lb

600 mm (24) Triple Grouser 2420 kg 5340 lb

700 mm (28) Triple Grouser 2650 kg 5840 lb

All weights are round up to nearest 10 kg and lb except for quick coupler and buckets Kg and lb were rounded up separately so some of the kg and lb do not match

Base machine includes 75 kg (165 lb) operator weight 90 fuel weight and undercarriage with center guard

Actual weight will depend on final machine configuration

17

316E L Hydraulic Excavator Specifications

Bucket and Stick Forces

Reach Boom 510 m (169)

Stick R29 (96) R26 (86) R225 (74)

General Duty

Bucket Digging Force (ISO) 111 kN 25000 lb 111 kN 25000 lb 111 kN 25000 lb

Stick Digging Force (ISO) 75 kN 16900 lb 80 kN 18000 lb 88 kN 19800 lb

18

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft

m ft

75 m kg 3950 3950 423 250 ft lb 60 m kg 3400 3400 579 200 ft lb 9600 9600 7500 7500 1875 45 m kg 5000 5000 4600 3250 3250 2750 667 150 ft lb 10850 10850 10000 6950 7200 6050 2177 30 m kg 6250 4700 5000 3100 3350 2400 712 100 ft lb 13450 10150 10750 6700 7300 5250 2334 15 m kg 7450 4400 4850 3000 3550 2300 724 50 ft lb 16100 9500 10450 6400 7850 5000 2376

Ground Line kg 5600 5600 7300 4250 4750 2900 3800 2350 704 lb 12950 12950 15700 9100 10200 6200 8350 5100 2310

ndash15 m kg 6100 6100 10 800 7700 7250 4200 4700 2850 4250 2600 649 ndash 50 ft lb 13600 13600 24600 16550 15550 9000 10150 6150 9350 5700 2125 ndash30 m kg 10 150 7850 7150 4250 5450 3300 548 ndash100 ft lb 21900 16900 15300 9200 12200 7300 1783

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 3250 3250 476 250 ft lb 7500 7500 7300 7300 1509 60 m kg 3500 3300 2850 2850 618 200 ft lb 6450 6450 6350 6350 2005 45 m kg 4600 4600 4300 3300 2750 2550 701 150 ft lb 10000 10000 9400 7000 6100 5600 2289 30 m kg 8850 8750 5900 4800 4800 3150 2800 2250 744 100 ft lb 18850 18850 12650 10300 10450 6750 6200 4950 2439 15 m kg 7200 4450 4900 3000 3400 2150 3000 2150 756 50 ft lb 15550 9600 10500 6400 6600 4700 2480

Ground Line kg 6250 6250 7300 4250 4750 2900 3400 2200 736 lb 14400 14400 15700 9100 10200 6200 7450 4750 2416

ndash15 m kg 5750 5750 10 150 7650 7250 4150 4700 2850 3900 2400 684 ndash 50 ft lb 12800 12800 23100 16400 15500 8950 10100 6100 8650 5250 2240 ndash30 m kg 9950 9950 10 750 7800 7300 4200 4900 2950 589 ndash100 ft lb 22400 22400 23200 16700 15650 9050 10850 6550 1919 ndash45 m kg 7750 7750 5400 4850 423 ndash150 ft lb 16300 16300 11900 11100 1351

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

19

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

Operating Weight and Ground Pressure

700 mm (28) 600 mm (24) 500 mm(20) Triple Grouser Shoes Triple Grouser Shoes Triple Grouser Shoes

kg lb kPa psi kg lb kPa psi kg lb kPa psi

Reach Boom ndash 510 m (169)

R29 (96) 17 800 39242 36 522 17 600 38801 42 609 17 300 38140 49 711

R26 (86) 17 700 39022 36 522 17 500 38581 41 595 17 300 38140 49 711

R225 (74) 17 700 39022 36 522 17 500 38581 41 595 17 200 37920 49 711

All weights are rounded up to nearest 100 kg and lb including General Duty 076 m3 (0994 yd3) bucket (610 kg [13448 lb]) Kg and lb were rounded up separately so some of the kg and lb do not match

Actual weight will depend on final machine configuration

Major Component Weights

Base Machine (with boom cylinder without counterweight front linkage and track) 5720 kg 12610 lb

Long Undercarriage 3770 kg 8310 lb

Counterweight ndash 28 mt (309 t) 2800 kg 6170 lb

Boom (includes lines pins and stick cylinder)

Reach Boom ndash 510 m (169) 1320 kg 2910 lb

Stick (includes lines pins bucket cylinder and bucket linkage)

R29 (96) 910 kg 2010 lb

R26 (86) 840 kg 1850 lb

R225 (74) 810 kg 1790 lb

Track Shoe (Longper two tracks)

500 mm (20) Triple Grouser 2190 kg 4830 lb

600 mm (24) Triple Grouser 2420 kg 5340 lb

700 mm (28) Triple Grouser 2650 kg 5840 lb

All weights are round up to nearest 10 kg and lb except for quick coupler and buckets Kg and lb were rounded up separately so some of the kg and lb do not match

Base machine includes 75 kg (165 lb) operator weight 90 fuel weight and undercarriage with center guard

Actual weight will depend on final machine configuration

17

316E L Hydraulic Excavator Specifications

Bucket and Stick Forces

Reach Boom 510 m (169)

Stick R29 (96) R26 (86) R225 (74)

General Duty

Bucket Digging Force (ISO) 111 kN 25000 lb 111 kN 25000 lb 111 kN 25000 lb

Stick Digging Force (ISO) 75 kN 16900 lb 80 kN 18000 lb 88 kN 19800 lb

18

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft

m ft

75 m kg 3950 3950 423 250 ft lb 60 m kg 3400 3400 579 200 ft lb 9600 9600 7500 7500 1875 45 m kg 5000 5000 4600 3250 3250 2750 667 150 ft lb 10850 10850 10000 6950 7200 6050 2177 30 m kg 6250 4700 5000 3100 3350 2400 712 100 ft lb 13450 10150 10750 6700 7300 5250 2334 15 m kg 7450 4400 4850 3000 3550 2300 724 50 ft lb 16100 9500 10450 6400 7850 5000 2376

Ground Line kg 5600 5600 7300 4250 4750 2900 3800 2350 704 lb 12950 12950 15700 9100 10200 6200 8350 5100 2310

ndash15 m kg 6100 6100 10 800 7700 7250 4200 4700 2850 4250 2600 649 ndash 50 ft lb 13600 13600 24600 16550 15550 9000 10150 6150 9350 5700 2125 ndash30 m kg 10 150 7850 7150 4250 5450 3300 548 ndash100 ft lb 21900 16900 15300 9200 12200 7300 1783

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 3250 3250 476 250 ft lb 7500 7500 7300 7300 1509 60 m kg 3500 3300 2850 2850 618 200 ft lb 6450 6450 6350 6350 2005 45 m kg 4600 4600 4300 3300 2750 2550 701 150 ft lb 10000 10000 9400 7000 6100 5600 2289 30 m kg 8850 8750 5900 4800 4800 3150 2800 2250 744 100 ft lb 18850 18850 12650 10300 10450 6750 6200 4950 2439 15 m kg 7200 4450 4900 3000 3400 2150 3000 2150 756 50 ft lb 15550 9600 10500 6400 6600 4700 2480

Ground Line kg 6250 6250 7300 4250 4750 2900 3400 2200 736 lb 14400 14400 15700 9100 10200 6200 7450 4750 2416

ndash15 m kg 5750 5750 10 150 7650 7250 4150 4700 2850 3900 2400 684 ndash 50 ft lb 12800 12800 23100 16400 15500 8950 10100 6100 8650 5250 2240 ndash30 m kg 9950 9950 10 750 7800 7300 4200 4900 2950 589 ndash100 ft lb 22400 22400 23200 16700 15650 9050 10850 6550 1919 ndash45 m kg 7750 7750 5400 4850 423 ndash150 ft lb 16300 16300 11900 11100 1351

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

19

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

316E L Hydraulic Excavator Specifications

Bucket and Stick Forces

Reach Boom 510 m (169)

Stick R29 (96) R26 (86) R225 (74)

General Duty

Bucket Digging Force (ISO) 111 kN 25000 lb 111 kN 25000 lb 111 kN 25000 lb

Stick Digging Force (ISO) 75 kN 16900 lb 80 kN 18000 lb 88 kN 19800 lb

18

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft

m ft

75 m kg 3950 3950 423 250 ft lb 60 m kg 3400 3400 579 200 ft lb 9600 9600 7500 7500 1875 45 m kg 5000 5000 4600 3250 3250 2750 667 150 ft lb 10850 10850 10000 6950 7200 6050 2177 30 m kg 6250 4700 5000 3100 3350 2400 712 100 ft lb 13450 10150 10750 6700 7300 5250 2334 15 m kg 7450 4400 4850 3000 3550 2300 724 50 ft lb 16100 9500 10450 6400 7850 5000 2376

Ground Line kg 5600 5600 7300 4250 4750 2900 3800 2350 704 lb 12950 12950 15700 9100 10200 6200 8350 5100 2310

ndash15 m kg 6100 6100 10 800 7700 7250 4200 4700 2850 4250 2600 649 ndash 50 ft lb 13600 13600 24600 16550 15550 9000 10150 6150 9350 5700 2125 ndash30 m kg 10 150 7850 7150 4250 5450 3300 548 ndash100 ft lb 21900 16900 15300 9200 12200 7300 1783

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 3250 3250 476 250 ft lb 7500 7500 7300 7300 1509 60 m kg 3500 3300 2850 2850 618 200 ft lb 6450 6450 6350 6350 2005 45 m kg 4600 4600 4300 3300 2750 2550 701 150 ft lb 10000 10000 9400 7000 6100 5600 2289 30 m kg 8850 8750 5900 4800 4800 3150 2800 2250 744 100 ft lb 18850 18850 12650 10300 10450 6750 6200 4950 2439 15 m kg 7200 4450 4900 3000 3400 2150 3000 2150 756 50 ft lb 15550 9600 10500 6400 6600 4700 2480

Ground Line kg 6250 6250 7300 4250 4750 2900 3400 2200 736 lb 14400 14400 15700 9100 10200 6200 7450 4750 2416

ndash15 m kg 5750 5750 10 150 7650 7250 4150 4700 2850 3900 2400 684 ndash 50 ft lb 12800 12800 23100 16400 15500 8950 10100 6100 8650 5250 2240 ndash30 m kg 9950 9950 10 750 7800 7300 4200 4900 2950 589 ndash100 ft lb 22400 22400 23200 16700 15650 9050 10850 6550 1919 ndash45 m kg 7750 7750 5400 4850 423 ndash150 ft lb 16300 16300 11900 11100 1351

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

19

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft

m ft

75 m kg 3950 3950 423 250 ft lb 60 m kg 3400 3400 579 200 ft lb 9600 9600 7500 7500 1875 45 m kg 5000 5000 4600 3250 3250 2750 667 150 ft lb 10850 10850 10000 6950 7200 6050 2177 30 m kg 6250 4700 5000 3100 3350 2400 712 100 ft lb 13450 10150 10750 6700 7300 5250 2334 15 m kg 7450 4400 4850 3000 3550 2300 724 50 ft lb 16100 9500 10450 6400 7850 5000 2376

Ground Line kg 5600 5600 7300 4250 4750 2900 3800 2350 704 lb 12950 12950 15700 9100 10200 6200 8350 5100 2310

ndash15 m kg 6100 6100 10 800 7700 7250 4200 4700 2850 4250 2600 649 ndash 50 ft lb 13600 13600 24600 16550 15550 9000 10150 6150 9350 5700 2125 ndash30 m kg 10 150 7850 7150 4250 5450 3300 548 ndash100 ft lb 21900 16900 15300 9200 12200 7300 1783

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 500 mm (20) triple grouser

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 3250 3250 476 250 ft lb 7500 7500 7300 7300 1509 60 m kg 3500 3300 2850 2850 618 200 ft lb 6450 6450 6350 6350 2005 45 m kg 4600 4600 4300 3300 2750 2550 701 150 ft lb 10000 10000 9400 7000 6100 5600 2289 30 m kg 8850 8750 5900 4800 4800 3150 2800 2250 744 100 ft lb 18850 18850 12650 10300 10450 6750 6200 4950 2439 15 m kg 7200 4450 4900 3000 3400 2150 3000 2150 756 50 ft lb 15550 9600 10500 6400 6600 4700 2480

Ground Line kg 6250 6250 7300 4250 4750 2900 3400 2200 736 lb 14400 14400 15700 9100 10200 6200 7450 4750 2416

ndash15 m kg 5750 5750 10 150 7650 7250 4150 4700 2850 3900 2400 684 ndash 50 ft lb 12800 12800 23100 16400 15500 8950 10100 6100 8650 5250 2240 ndash30 m kg 9950 9950 10 750 7800 7300 4200 4900 2950 589 ndash100 ft lb 22400 22400 23200 16700 15650 9050 10850 6550 1919 ndash45 m kg 7750 7750 5400 4850 423 ndash150 ft lb 16300 16300 11900 11100 1351

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

19

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 500 mm (20) triple grouser

75 m 250 ft 60 m 200 ft 45 m 150 ft 30 m 100 ft 15 m 50 ft

Ground Line

ndash15 m ndash 50 ft ndash30 m ndash100 ft ndash45 m ndash150 ft

kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb kg lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3350 2650 2650 643 7350 7150 5800 5800 2089 4050 3300 2550 2400 723 8850 7050 5650 5350 2363

8000 8000 5500 4800 4600 3150 3300 2200 2650 2150 766 17000 17000 11900 10400 10000 6750 6050 4750 5800 4700 2509

7100 7100 6900 4450 4850 3000 3500 2150 2850 2050 777 17000 17000 14900 9600 10450 6400 7500 4600 6250 4450 2548

7050 7050 7300 4200 4750 2850 3450 2100 3200 2050 758 16150 16150 15650 9050 10150 6100 7050 4500 2487

5700 5700 10 100 7550 7200 4100 4650 2800 3700 2250 707 12750 12750 22900 16150 15400 8850 10000 6000 8150 4950 2316

9300 9300 11 100 7650 7200 4150 4700 2800 4550 2750 616 20850 20850 23950 16400 15450 8900 10100 6050 10050 6050 2007

8550 7950 5700 4350 5550 4200 460 18150 17050 12150 9550 1475

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft 30 m10 ft

6100 13600

6100 13600

5600 12950 10 800 24600 10 150 21900

5600 12950

7800 16750

7950 17100

45 m15 ft

9600 5000

10850 6250

13450 7450

16100 7400

15850 7350

15750 7150

15300

9600 5000

10850 4750

10300 4450 9600 4300 9200 4250 9150 4300 9300

4600 10000

5050 10900

4900 10550

4800 10350

4800 10300

60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2750 667 7000 7200 6100 2177 3150 3350 2450 712 6750 7300 5350 2334 3000 3550 2300 724 6500 7850 5050 2376 2900 3850 2350 704 6250 8450 5150 2310 2900 4300 2600 649 6200 9450 5750 2125

5550 3350 548 12250 7400 1783

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

20

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft

3500 6450 4300 9400 4800

10450 4950

10600 4800

10350 4750

10250

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7750 16600

7850 16900 7750

16300

7500

4600 10000

5900 12650

7200 15550

7400 15900

7350 15700

7400 15850

7500

4600 10000

4850 10400

4500 9700 4300 9250 4200 9100 4250 9200

60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3350 2850 2850 618 6450 6350 6350 2005

3300 2750 2550 701 7100 6100 5700 2289 3200 2800 2300 744 6850 6200 5000 2439 3050 3400 2200 3000 2150 756 6500 6600 4750 2480 2900 3400 2200 736 6250 7450 4850 2416 2850 3950 2400 684

6150 8750 5350 2240 4950 3000 589

11000 6650 1919 5400 4900 423

11900 11200 1351

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 600 mm (24) triple grouser

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

2950 2950 508 6500 6500 1621

3650 3400 2650 2650 643 7350 7250 5800 5800 2089 4050 3350 2550 2450 723 8850 7150 5650 5400 2363

8000 8000 5500 4900 4600 3200 3300 2250 2650 2150 766 17000 17000 11900 10500 10000 6850 6050 4800 5800 4800 2509

7100 7100 6900 4500 4950 3000 3550 2200 2850 2050 777 17000 17000 14900 9700 10600 6500 7600 4650 6250 4550 2548

7050 7050 7400 4250 4800 2900 3500 2100 3200 2100 758 16150 16150 15850 9150 10300 6200 7050 4600 2487

5700 5700 10 100 7650 7250 4150 4700 2800 3750 2300 707 12750 12750 22900 16350 15600 8950 10150 6050 8250 5000 2316

9300 9300 11 100 7750 7300 4200 4750 2850 4600 2750 616 20850 20850 23950 16600 15650 9000 10250 6150 10200 6100 2007

8550 8000 5700 4400 5550 4250 460 18150 17250 12150 9650 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

21

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

316E L Hydraulic Excavator Specifications

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R225 (74) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb

15 m5 ft

6100 6100 13600 13600

30 m10 ft

5600 12950 10 800 24600 10 150 21900

5600 12950

7900 16950

8050 17300

45 m15 ft 60 m20 ft

m ft

3950 3950 423

3400 3400 579 7500 7500 1875

3300 3250 2800 667 7100 7200 6200 2177 3200 3350 2450 712 6850 7300 5400 2334 3050 3550 2350 724 6550 7850 5150 2376 2950 3900 2400 704 6350 8550 5250 2310 2950 4350 2650 649 6300 9600 5850 2125

5550 3400 548 12250 7500 1783

9600 5000

10850 6250

13450 7450

16100 7500

16100 7450

16000 7150

15300

9600 5000

10850 4850

10400 4500 9750 4350 9350 4300 9250 4400 9400

4600 10000

5050 10950

5000 10700

4900 10500

4850 10450

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R26 (86) Shoes ndash 700 mm (28) triple grouser with step

75 m kg 250 ft lb 60 m kg 200 ft lb 45 m kg 150 ft lb 30 m kg 100 ft lb 15 m kg 50 ft lb

Ground Line kg lb

ndash15 m kg ndash 50 ft lb ndash30 m kg ndash100 ft lb ndash45 m kg ndash150 ft lb

15 m5 ft

5750 5750 12800 12800

9950 9950 22400 22400

30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

3250 3250 476 7300 7300 1509

3400 2850 2850 618 6450 6350 6350 2005

3350 2750 2600 701 7200 6100 5750 2289 3200 2800 2300 744 6900 6200 5100 2439 3050 3400 2250 3000 2200 756 6600 6600 4800 2480 2950 3400 2250 736 6350 7450 4900 2416 2900 4050 2450 684

6250 8850 5400 2240 5000 3050 589

11150 6750 1919 5400 4950 423

11900 11350 1351

3500 6450 4300 9400 4800

10450 5000

10750 4900

10500 4800

10350

8850 18850

6250 14400 10 150 23100 10 750 23200

7750 16300

8850 18850

6250 14400

7850 16850

8000 17100 7750

16300

7500

4600 10000

5900 12650

7200 15550

7500 16100

7450 15950 7450

16000

7500

4600 10000

4900 10550

4550 9800 4350 9350 4300 9200 4350 9300

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

22

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

Reach Boom Lift Capacities

Load Point Height Load at Maximum Reach Load Radius Over Front Load Radius Over Side

Boom ndash 510 m (169) Counterweight ndash 28 mt (309 t) Bucket ndash None

Stick ndash R29 (96) Shoes ndash 700 mm (28) triple grouser with step

15 m5 ft 30 m10 ft 45 m15 ft 60 m20 ft 75 m25 ft

m ft

75 m kg 2950 2950 508 250 ft lb 6500 6500 1621 60 m kg 3650 3450 2650 2650 643 200 ft lb 7350 7350 5800 5800 2089 45 m kg 4050 3350 2550 2500 723 150 ft lb 8850 7250 5650 5450 2363 30 m kg 8000 8000 5500 4950 4600 3200 3300 2300 2650 2200 766 100 ft lb 17000 17000 11900 10600 10000 6900 6050 4850 5800 4850 2509 15 m kg 7100 7100 6900 4550 5000 3050 3600 2200 2850 2100 777 50 ft lb 17000 17000 14900 9850 10750 6550 7700 4750 6250 4600 2548

Ground Line kg 7050 7050 7500 4300 4850 2950 3500 2150 3200 2100 758 lb 16150 16150 16050 9300 10450 6300 7050 4650 2487

ndash15 m kg 5700 5700 10 100 7750 7350 4200 4800 2850 3800 2300 707 ndash 50 ft lb 12750 12750 22900 16600 15800 9100 10300 6150 8400 5100 2316 ndash30 m kg 9300 9300 11 100 7850 7400 4250 4800 2900 4650 2800 616 ndash100 ft lb 20850 20850 23950 16 800 15900 9150 10350 6250 10300 6200 2007 ndash45 m kg 8550 8100 5700 4450 5550 4300 460 ndash150 ft lb 18150 17450 12150 9800 1475

Indicates that the load is limited by hydraulic lifting capacity rather than tipping load The above loads are in compliance with hydraulic excavator lift capacity standard ISO 105672007 They do not exceed 87 of hydraulic lifting capacity or 75 of tipping load Weight of all lifting accessories must be deducted from the above lifting capacities Lifting capacities are based on the machine standing on a firm uniform supporting surface The use of a work tool attachment point to handlelift objects could affect the machine lift performance

Lift capacity stays within plusmn 5 for all available track shoes

Always refer to the appropriate Operation and Maintenance Manual for specific product information

23

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

316E L Hydraulic Excavator Specifications

316E L Work Tool Offering Guide

Boom Type Reach Boom

Stick Size R29 (96) R26 (86) R225 (74)

Hydraulic Hammer H110Es H110Es H110Es H115Es H115Es H115Es H120Es H120Es H120Es

Multi-Processor MP15 CC Jaw MP15 CR Jaw MP15 PS Jaw

MP15 S Jaw

Crusher P315

Pulverizer P215

Demolition and Sorting Grapple G310B G310B G310B G315B

Mobile Scrap and Demolition Shear S325 S325 S325

Compactor (Vibratory Plate) CVP75 CVP75 CVP75

Contractorsrsquo Grapple G115B G115B G115B

Orange Peel Grapple

Trash Grapple

Thumbs These work tools are available for the 316E L Rakes Consult your Cat dealer for proper match

Center-Lock Pin Grabber Coupler

Dedicated Quick Coupler

Offerings not available in all areas Matches are dependent on excavator configurations Consult your Cat dealer to determine what is offered in your area and for proper work tool match

Pin-on or CW coupler

Pin-on only

Over the front only

Over the front only with CW coupler

Boom Mount

24

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

Bucket Specifications and Compatibility

Width Capacity Weight Fill

m3 yd3 kg lb

Reach Boom

mm in R29 R26 R225

With Centerlock Quick Coupler

General Duty (GD)

1705

500 20 030 039 403 888 100

600 24 035 046 433 954 100

750 30 049 064 476 1049 100

900 36 062 081 537 1184 100

1050 42 076 100 590 1301 100

1200 48 091 119 645 1422 100

Maximum load pin-on (payload + bucket) kg

lb

1815

3758 4000 4298

The above loads are in compliance with hydraulic excavator standard EN474 they do not exceed 87 of Maximum Material Densityhydraulic lifting capacity or 75 of tipping capacity with front linkage fully extended at ground line with bucket curled 2100 kgm3 (3500 lbyd3)

1800 kgm3 (3000 lbyd3)Capacity based on ISO 7451

1500 kgm3 (2500 lbyd3)Bucket weight with General Duty tips

1200 kgm3 (2000 lbyd3)Densities with 30 m (910) thumb stick do not consider thumb weight

Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products Use of work tools including buckets which are outside of Caterpillarrsquos recommendations or specifications for weight dimensions flows pressures etc may result in less-than-optimal performance including but not limited to reductions in production stability reliability and component durability Improper use of a work tool resulting in sweeping prying twisting andor catching of heavy loads will reduce the life of the boom and stick

25

1950

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

316E L Standard Equipment

Standard Equipment

Standard equipment may vary Consult your Cat dealer for details

ENGINE

bull C44 ACERT diesel engine bull Biodiesel capable bull Meets European Union Stage IIIB and

US Tier 4 Interim emission standards bull 2300 m altitude capability bull Electric priming pump bull Automatic engine speed control bull Economy and high power modes bull Two-speed travel bull Side-by-side cooling system

(tilt-up ATAAC swing-out AC condenser) bull Radial seal air fi lter bull Primary filter with water separator

and water separator indicator bull Standard battery ndash18deg C (ndash04deg F) bull Screen filter in fuel line bull Secondary fuel fi lter

HYDRAULIC SYSTEM

bull Quick drains engine and hydraulic oil (QuickEvac)

bull Regeneration circuit for boom and stick bull Reverse swing dampening valve bull Automatic swing parking brake bull High-performance hydraulic return fi lter bull Capability of installing HP stackable valve

and medium and QC valve bull Capability of installing additional auxiliary

pump and circuit

CAB

bull Pressurized operator station with positive fi ltration

bull Mirror package bull Sliding upper door window

(left-hand cab door) bull Glass-breaking safety hammer bull Removable lower windshield

with in cab storage bracket bull Coat hook bull Beverage holder bull Literature holder bull AMFM Radio with MP3 auxiliary

audio port bull Two 12V stereo speakers bull Storage shelf suitable for lunch or toolbox bull Color LCD display with warning

fi lterfluid change and working hour information

bull Adjustable armrest bull Height adjustable joystick consoles bull Neutral lever (lock out) for all controls bull Travel control pedals

with removable hand levers bull Two power outlets 10 amp (total) bull Laminated glass front window 7030 split

(tempered glass for bottom front window) bull Sunscreen bull Seatbelt (76 mm [3]) bull Windshield wiper lower with washer bull Seat high-back air suspension heated

and cooled bull Cab mirror bull Level sensor

FRONT LINKAGE

bull Bucket linkage with lifting eye

UNDERCARRIAGE

bull Grease Lubricated Track GLT2 resin seal bull Towing eye on base frame bull Swivel guard

COUNTERWEIGHT

bull 28 mt (309 t)

ELECTRICAL

bull 80 amp alternator bull Circuit breaker bull Capability to electrically connect a beacon

LIGHTS

bull Halogen boom lights (left and right) bull Time delay function for boom light

and cab light bull Exterior lights integrated into storage box

SECURITY

bull Cat one key security system bull Door locks bull Cap locks on fuel and hydraulic tanks bull Lockable external toolstorage box bull Signalingwarning horn bull Secondary engine shutoff switch bull Openable skylight for emergency exit bull Guardrail and handrail bull Rearview camera bull Travel alarm

26

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)

For more complete information on Cat products dealer services and industry solutions visit us on the web at wwwcatcom

copy 2013 Caterpillar Inc

All rights reserved

Materials and specifications are subject to change without notice Featured machines in photos may include additional equipment See your Cat dealer for available options

CAT CATERPILLAR SAFETYCATCOM their respective logos ldquoCaterpillar Yellowrdquo and the ldquoPower Edgerdquo trade dress as well as corporate and product identity used herein are trademarks of Caterpillar and may not be used without permission

AEHQ7062 (08-2013) (ANZ)