English

1 Knowing the device 1.1 Product Overview 1.2 Battey LED indicator 1.3 Remote contents 1.4 Package contents2 Getting started 2.1 Charging the battery 2.2 Plug in the WiFi USB dongle 2.3 Insert a micro SD card 2.4 Turn on the projector 2.5 Adjusting the focus 2.6 Install the WiFi application program3 Functions and operations 3.1 Playback the contents from the inserted micro SD card or connected USB 3.1.1 Playback photo 3.1.2 Project MS Office documents 3.1.3 Play music 3.1.4 Play video 3.2 Play contents from mobile devices by WiFi connection 3.2.1 Configure WiFi connection 3.2.2 Select WiFi connection mode 3.2.3 Project from Windows-based Notebook PCs 3.2.4 Project from Android based smart phones or tablet PCs 3.2.5 Projecting from Apple iOS based smart phones or tablet PCs 3.2.6 Projecting from Mac OS-based Notebook PCs4 Charging your mobile devices5 Specifications

1

1

2

3

3

3

3-4

4

4

4-5

5

5-7

7

7

8

9-10

11

11-12

12

12-13

13-15

15-16

16-17

17

17-18

18

19-20

Table of Contents

1.Knowing the device 1.1 Product Overview

1

Product Overview

Lens

Speaker

Menu buttonRight buttonLeft buttonOK buttonUp buttonDown buttonRetum button

Micro SDcard slot

WiFi/USB port

DC-IN port

Headphone jack

Power indicator(Blue)

DC-OUT port

IR receiver

Focus ring

Charge statusindicator(Green/Red)

Power switchLow charger

power indicator(Red)

- Plug the AC power adapter into the DC-IN jack of the projector, and connect the other end to the power source. or - Connect the small end of the supplied USB cable to the USB port of the device, and the large end to a powered PC. Make sure the projector is powered off. 2.2 Plug in the WiFi USB dongle To enable the WiFi function, please plug the bundled WiFi USB dongle into the WiFi/USB port on the device. WiFi LED indicator: - LED light is on when WiFi function is enabled. - LED light is flashing when WiFi function is active. 2.3 Insert a micro SD card - Hold the micro SD card by the edges and gently insert it into the slot until it reached the bottom of the slot. - To remove the memory card, gently push the top edge of the card inwards and it will pop up slightly, then pull the card out of the slot. 2.4 Turn on the projector Slide the power switch to the right end. Hold it till power LED is on, then the

1.4 Package contents - WiFi mini projector - WiFi USB dongle - Micro USB charger cable - Power adapter - Remote controller - Users manual

2. Getting started 2.1 Charging the battery The internal battery of the projector may not be fully charged for the first time. You can charge the battery by the following two ways:

3.1.1 Playback photo Use the arrow keys to select Photoitem and the memory device (SD/TF or USB disk). And follow the file navigator to select target photo file. This projector supports *.jpg, *.jpeg, and *.bmp image formats. When displaying a photo, press OK key on the remotecontroller to active the function bar with following functions. Rotate - Enlarge Last photo Next photo Slideshow Erase Copy Exit You also can use the left and right keys on the projector or remote controller to forward and backward the displayed photo. From Setting item on the main menu, you can active slideshow function, select display ratio (original size or full screen), or slideshow duration.

For Apple iOS based iPhone or iPad devices - Please go to Apple Store to search EZ-Display and install in your iPhone or iPad device.

3. Functions and operations There are operation icons on main menu,WIFI DISPLAY, PHOTO,MUSIC,VIDEOand SETTING.

3.1 Playback the contents from the inserted micro SD card or connected USB storage device. When turning on the projector, you can use the bundled remote controller or arrow keys on the device to select the play items or make system setup. To make system setup, go to SETTING on main menu and select System Setup where you can select the display language, view the system version and reset to factory default settings. Please be noted that the WiFi USB dongle should be connected first when making setting reset.

- Apple Mac operation system : Mac OS 10.7 or later EZ View program - Android operation system : Android ICS 4.0 or above - Apple iOS operation system : iOS 5.0 or above Download and install application programs For Windows, Android or Apple Mac based mobile devices. - Turn on the projector and select WIFI item from main menu. You can identify the default device name Projector-xxxxxx (xxxxxx is a series ID code) and its default IP address 192.168.111.1. - Turn on the WiFi function of your mobile device and search for the device Projector-xxxxxx. - Enter the link pass word (PSK)11112222 to connect with the projector. - Open the Internet explorer program of your mobile device (like I.E.) and search the device IP address 192.168.111.1. - The program download page will be displayed. Please click the corresponding program to download it for your mobile device. For Windows users, you need to restart the PC after successful installation.

projector will be turned on. To turn off the projector, please slide the power switch to the right end again till power LED is off.If you just want to turn off the projector temporarily, press the power button on the remote controller to shut down the projector light for saving power. To light up the projector, press the power button again.

2.5 Adjusting the focus Adjust the focus by using the focus wheel to get a sharp and clear picture.

2.6 Install the WiFi application programs To display contents from your mobile devices like smart phone, tablet PC or notebook PC with the projector, you need to install their corresponding application programs first.

EZ View program is designed for Windows based or Mac OS based notebook PC. EZ View program is designed for Android based or iOS based smart phones and tablet PCs.

Before installing the program, please check if your mobile device meets the operation system requirement of EZ View as below.

EZ View program - Windows operation system : Windows XP/Vista/7 (Note: Audio function is NOT supported for Windows 7.

3.1.3 Play music Use the arrow keys to select Music item and the memory device (SD/TF or USB disk). And follow the file navigator to select the target music file. This projector supports mp3, wma, ogg, wav music formats. When playing music, you can use the keys on the projector or remote controller to select music file, pause or play the music or adjust the volume. From Setting item on the main menu, you can select playing single music or sequence music.

3.1.4 Play video Use the arrow keys to select Video item and the memory device (SD/TF or USB disk). And follow the file navigator to select target video file. This projector supports the most popular video formats like MPEG1/2/4,

3.1.2 Project MS Office and PDF documents - Play document files like MS Word, Excel, PowerPoint and Adobe PDF from USB drive or Micro SD card Use the arrow keys and OK key on the remote controller to select the OFFICE icon on main menu and then the file source (USB drive or Micro SD card). Choice the target file from the displayed file list to project out. See the supported list of MS Office files Some functions are available for viewing the projected document and they can only be executed by the remote controller. The function keys are defined as below Zoom in Zoom out Scroll up Scroll down Move to right Move to left Last page Next page

Or click Refresh to search the available router again. - Now the Client Mode is setup completely. - Press return key to exit. The mobile devices will be able to go through this projector to access Internet. Different WiFi devices may use different encryption way. If the screen as right side is displayed when you link any mobile device, please do following to build the connection. Format: Select ASCII or HEX16 (refer to the user manual of this mobile device). INDEX: Select 1 PSK: Enter the assigned PSK code.

3.2.3 Project from Windows-based Notebook PCs Make sure EZ WiFi program has been installed on your Notebook PC first. - Turn on this projector and go to EZ View. - Turn on WiFi function on your Notebook PC. - Open EZ View program. It will search and link this projector

Client (Internet access) mode: Allow the mobile devices to connect Internet for displaying the web contents (likeYoutube) from the projector wirelessly. In Client mode, the projector must connect to an accessible WiFi router which linked to Internet.

Follow the steps below to setup Client mode. - Select WiFi DISPLAY item from main menu - Click Right key to move to WiFi setting page - Click Right key again to move to Router setting page - Select ON and press OK to turn on Client Mode. The Router setting page will list the available WiFi devices - Use Down key to select the router to be connected and click OK to confirm it. Then enter the pass key of this router in the PSK column and click OK.

OK to confirm your selection. - Press Left key to go back to WiFi Display page

3.2.2 Select WiFi connection mode This projector can be set up in two WiFi connection modes. AP (Pear-to-pear) mode: This is the default mode. It allows the mobile devices to download the application programs from this projector or to project the multimedia contents from the projector wirelessly.

H264, WMV, RMVB with up to 1080p resolution. Please refer to the Chapter 5 Specifications for details. When playing video, you can use the keys on the projector or remote controller to select video file, fast forward or backward, pause/play video, stop play, or adjust the volume. From Setting item on the main menu, you can select display ratio (original size or full screen), or playing single or sequence video.

3.2 Play contents from mobile devices by WiFi connection Go to main menu and select WIFI DISPLAY item 3.2.1 Configure WiFi connection - Reset the device name and connection pass word (if needed) The default device name and link pass word (PSK) are Projector-xxxxxx (xxxxxx is a series ID code) and 11112222. You may reset them from WIFI DISPLAY page. - Click WIFI DISPLAY item and then press right key to open WiFi setting page. - Use Up/Down key to select Device name or PSK (pass word) item and press OK to reset it. - Use the on-screen key board and arrow keys on remote controller to enter the new setting. - Press OK to confirm each selected character or number and press EXIT to close the on-screen key board. - Use Down key to select to save the new Device name /PSK settings or X to clean the SSID/PSK table for esetting and press

- EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs.

4. Charging your mobile devices The internal battery of the projector can not only be used for projection, but also charge your mobile device for emergency. - Please turn off the projector and switch the power switch to the Charger position before charging your mobile device. - Plug bundled USB cable to both end of micro USB DC-in port of your mobile phone and DC-OUT USB port of the projector. This is for emergent charging and may not be able to charge your mobile device to be 100% power level. The charger LED indicator

Note: Splitter display feature only supports playing photos. - Select the function from scroll bar or pull down menu. 3.2.5 Projecting from Apple iOS based smart phones or tablet PCs (like iPhones or iPads) - Make sure EZ View program installed first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function of the mobile device and link to this projector. - Open EZ View program - EZ View program provides document display, hoto display, Internet access, Dropbox display, Live camera, video display, and splitter display (up to 4 access devices)/On-screen sketch.

3.2.6 Projecting from Mac OS-based Notebook PCs Make sure EZ View program has been installed on your Mac Notebook PC first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function on your Notebook PC. - Open EZ View program and it will search and link this projector automatically.

automatically. - EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs. Splitter display: allow up to 4 PCs to project screen from the projector at the same time. But playing video contents are not supported. Mirror display: the projector will project the same screen as the PC does. Extend Mode: the projector works as a 2nd monitor to extend the screen width of the PC. 3.2.4 Project from Android

based smart phones or tablet PCs Make sure EZ View program

has been installed first. - Turn on the projector and open WiFi Display page. - Turn on WiFi function of the mobile device and link

to this projector. - Open EZ View program from your mobile device. - EZ View program provides document display, photo display, Internet access, Live camera, video display, and splitter display (up to 4 access devices)/on-screen sketch functions for your needs.

2 - Plug the AC power adapter into the DC-IN jack of the projector, and connect the other end to the power source. or - Connect the small end of the supplied USB cable to the USB port of the device, and the large end to a powered PC. Make sure the projector is powered off. 2.2 Plug in the WiFi USB dongle To enable the WiFi function, please plug the bundled WiFi USB dongle into the WiFi/USB port on the device. WiFi LED indicator: - LED light is on when WiFi function is enabled. - LED light is flashing when WiFi function is active. 2.3 Insert a micro SD card - Hold the micro SD card by the edges and gently insert it into the slot until it reached the bottom of the slot. - To remove the memory card, gently push the top edge of the card inwards and it will pop up slightly, then pull the card out of the slot. 2.4 Turn on the projector Slide the power switch to the right end. Hold it till power LED is on, then the

1.4 Package contents - WiFi mini projector - WiFi USB dongle - Micro USB charger cable - Power adapter - Remote controller - Users manual

2. Getting started 2.1 Charging the battery The internal battery of the projector may not be fully charged for the first time. You can charge the battery by the following two ways:

3.1.1 Playback photo Use the arrow keys to select Photoitem and the memory device (SD/TF or USB disk). And follow the file navigator to select target photo file. This projector supports *.jpg, *.jpeg, and *.bmp image formats. When displaying a photo, press OK key on the remotecontroller to active the function bar with following functions. Rotate - Enlarge Last photo Next photo Slideshow Erase Copy Exit You also can use the left and right keys on the projector or remote controller to forward and backward the displayed photo. From Setting item on the main menu, you can active slideshow function, select display ratio (original size or full screen), or slideshow duration.

For Apple iOS based iPhone or iPad devices - Please go to Apple Store to search EZ-Display and install in your iPhone or iPad device.

3. Functions and operations There are operation icons on main menu,WIFI DISPLAY, PHOTO,MUSIC,VIDEOand SETTING.

3.1 Playback the contents from the inserted micro SD card or connected USB storage device. When turning on the projector, you can use the bundled remote controller or arrow keys on the device to select the play items or make system setup. To make system setup, go to SETTING on main menu and select System Setup where you can select the display language, view the system version and reset to factory default settings. Please be noted that the WiFi USB dongle should be connected first when making setting reset.

- Apple Mac operation system : Mac OS 10.7 or later EZ View program - Android operation system : Android ICS 4.0 or above - Apple iOS operation system : iOS 5.0 or above Download and install application programs For Windows, Android or Apple Mac based mobile devices. - Turn on the projector and select WIFI item from main menu. You can identify the default device name Projector-xxxxxx (xxxxxx is a series ID code) and its default IP address 192.168.111.1. - Turn on the WiFi function of your mobile device and search for the device Projector-xxxxxx. - Enter the link pass word (PSK)11112222 to connect with the projector. - Open the Internet explorer program of your mobile device (like I.E.) and search the device IP address 192.168.111.1. - The program download page will be displayed. Please click the corresponding program to download it for your mobile device. For Windows users, you need to restart the PC after successful installation.

projector will be turned on. To turn off the projector, please slide the power switch to the right end again till power LED is off.If you just want to turn off the projector temporarily, press the power button on the remote controller to shut down the projector light for saving power. To light up the projector, press the power button again.

2.5 Adjusting the focus Adjust the focus by using the focus wheel to get a sharp and clear picture.

2.6 Install the WiFi application programs To display contents from your mobile devices like smart phone, tablet PC or notebook PC with the projector, you need to install their corresponding application programs first.

EZ View program is designed for Windows based or Mac OS based notebook PC. EZ View program is designed for Android based or iOS based smart phones and tablet PCs.

Before installing the program, please check if your mobile device meets the operation system requirement of EZ View as below.

EZ View program - Windows operation system : Windows XP/Vista/7 (Note: Audio function is NOT supported for Windows 7.

3.1.3 Play music Use the arrow keys to select Music item and the memory device (SD/TF or USB disk). And follow the file navigator to select the target music file. This projector supports mp3, wma, ogg, wav music formats. When playing music, you can use the keys on the projector or remote controller to select music file, pause or play the music or adjust the volume. From Setting item on the main menu, you can select playing single music or sequence music.

3.1.4 Play video Use the arrow keys to select Video item and the memory device (SD/TF or USB disk). And follow the file navigator to select target video file. This projector supports the most popular video formats like MPEG1/2/4,

3.1.2 Project MS Office and PDF documents - Play document files like MS Word, Excel, PowerPoint and Adobe PDF from USB drive or Micro SD card Use the arrow keys and OK key on the remote controller to select the OFFICE icon on main menu and then the file source (USB drive or Micro SD card). Choice the target file from the displayed file list to project out. See the supported list of MS Office files Some functions are available for viewing the projected document and they can only be executed by the remote controller. The function keys are defined as below Zoom in Zoom out Scroll up Scroll down Move to right Move to left Last page Next page

Or click Refresh to search the available router again. - Now the Client Mode is setup completely. - Press return key to exit. The mobile devices will be able to go through this projector to access Internet. Different WiFi devices may use different encryption way. If the screen as right side is displayed when you link any mobile device, please do following to build the connection. Format: Select ASCII or HEX16 (refer to the user manual of this mobile device). INDEX: Select 1 PSK: Enter the assigned PSK code.

3.2.3 Project from Windows-based Notebook PCs Make sure EZ WiFi program has been installed on your Notebook PC first. - Turn on this projector and go to EZ View. - Turn on WiFi function on your Notebook PC. - Open EZ View program. It will search and link this projector

Client (Internet access) mode: Allow the mobile devices to connect Internet for displaying the web contents (likeYoutube) from the projector wirelessly. In Client mode, the projector must connect to an accessible WiFi router which linked to Internet.

Follow the steps below to setup Client mode. - Select WiFi DISPLAY item from main menu - Click Right key to move to WiFi setting page - Click Right key again to move to Router setting page - Select ON and press OK to turn on Client Mode. The Router setting page will list the available WiFi devices - Use Down key to select the router to be connected and click OK to confirm it. Then enter the pass key of this router in the PSK column and click OK.

OK to confirm your selection. - Press Left key to go back to WiFi Display page

3.2.2 Select WiFi connection mode This projector can be set up in two WiFi connection modes. AP (Pear-to-pear) mode: This is the default mode. It allows the mobile devices to download the application programs from this projector or to project the multimedia contents from the projector wirelessly.

H264, WMV, RMVB with up to 1080p resolution. Please refer to the Chapter 5 Specifications for details. When playing video, you can use the keys on the projector or remote controller to select video file, fast forward or backward, pause/play video, stop play, or adjust the volume. From Setting item on the main menu, you can select display ratio (original size or full screen), or playing single or sequence video.

3.2 Play contents from mobile devices by WiFi connection Go to main menu and select WIFI DISPLAY item 3.2.1 Configure WiFi connection - Reset the device name and connection pass word (if needed) The default device name and link pass word (PSK) are Projector-xxxxxx (xxxxxx is a series ID code) and 11112222. You may reset them from WIFI DISPLAY page. - Click WIFI DISPLAY item and then press right key to open WiFi setting page. - Use Up/Down key to select Device name or PSK (pass word) item and press OK to reset it. - Use the on-screen key board and arrow keys on remote controller to enter the new setting. - Press OK to confirm each selected character or number and press EXIT to close the on-screen key board. - Use Down key to select to save the new Device name /PSK settings or X to clean the SSID/PSK table for esetting and press

- EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs.

4. Charging your mobile devices The internal battery of the projector can not only be used for projection, but also charge your mobile device for emergency. - Please turn off the projector and switch the power switch to the Charger position before charging your mobile device. - Plug bundled USB cable to both end of micro USB DC-in port of your mobile phone and DC-OUT USB port of the projector. This is for emergent charging and may not be able to charge your mobile device to be 100% power level. The charger LED indicator

Note: Splitter display feature only supports playing photos. - Select the function from scroll bar or pull down menu. 3.2.5 Projecting from Apple iOS based smart phones or tablet PCs (like iPhones or iPads) - Make sure EZ View program installed first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function of the mobile device and link to this projector. - Open EZ View program - EZ View program provides document display, hoto display, Internet access, Dropbox display, Live camera, video display, and splitter display (up to 4 access devices)/On-screen sketch.

3.2.6 Projecting from Mac OS-based Notebook PCs Make sure EZ View program has been installed on your Mac Notebook PC first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function on your Notebook PC. - Open EZ View program and it will search and link this projector automatically.

automatically. - EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs. Splitter display: allow up to 4 PCs to project screen from the projector at the same time. But playing video contents are not supported. Mirror display: the projector will project the same screen as the PC does. Extend Mode: the projector works as a 2nd monitor to extend the screen width of the PC. 3.2.4 Project from Android

based smart phones or tablet PCs Make sure EZ View program

has been installed first. - Turn on the projector and open WiFi Display page. - Turn on WiFi function of the mobile device and link

to this projector. - Open EZ View program from your mobile device. - EZ View program provides document display, photo display, Internet access, Live camera, video display, and splitter display (up to 4 access devices)/on-screen sketch functions for your needs.

StatusCharging status indicator

LED colorBattery is being chargedBattery is completely charged

RedGreenONON

ONOFF

Low PWRLow charger power indicator

LED color

Battery low when charging external device

RedON

Power indicator

LED color

Power is ON

Power is OFF

BlueONOFF

1.2 Battery LED indicator

3 - Plug the AC power adapter into the DC-IN jack of the projector, and connect the other end to the power source. or - Connect the small end of the supplied USB cable to the USB port of the device, and the large end to a powered PC. Make sure the projector is powered off. 2.2 Plug in the WiFi USB dongle To enable the WiFi function, please plug the bundled WiFi USB dongle into the WiFi/USB port on the device. WiFi LED indicator: - LED light is on when WiFi function is enabled. - LED light is flashing when WiFi function is active. 2.3 Insert a micro SD card - Hold the micro SD card by the edges and gently insert it into the slot until it reached the bottom of the slot. - To remove the memory card, gently push the top edge of the card inwards and it will pop up slightly, then pull the card out of the slot. 2.4 Turn on the projector Slide the power switch to the right end. Hold it till power LED is on, then the

1.4 Package contents - WiFi mini projector - WiFi USB dongle - Micro USB charger cable - Power adapter - Remote controller - Users manual

2. Getting started 2.1 Charging the battery The internal battery of the projector may not be fully charged for the first time. You can charge the battery by the following two ways:

3.1.1 Playback photo Use the arrow keys to select Photoitem and the memory device (SD/TF or USB disk). And follow the file navigator to select target photo file. This projector supports *.jpg, *.jpeg, and *.bmp image formats. When displaying a photo, press OK key on the remotecontroller to active the function bar with following functions. Rotate - Enlarge Last photo Next photo Slideshow Erase Copy Exit You also can use the left and right keys on the projector or remote controller to forward and backward the displayed photo. From Setting item on the main menu, you can active slideshow function, select display ratio (original size or full screen), or slideshow duration.

For Apple iOS based iPhone or iPad devices - Please go to Apple Store to search EZ-Display and install in your iPhone or iPad device.

3. Functions and operations There are operation icons on main menu,WIFI DISPLAY, PHOTO,MUSIC,VIDEOand SETTING.

3.1 Playback the contents from the inserted micro SD card or connected USB storage device. When turning on the projector, you can use the bundled remote controller or arrow keys on the device to select the play items or make system setup. To make system setup, go to SETTING on main menu and select System Setup where you can select the display language, view the system version and reset to factory default settings. Please be noted that the WiFi USB dongle should be connected first when making setting reset.

- Apple Mac operation system : Mac OS 10.7 or later EZ View program - Android operation system : Android ICS 4.0 or above - Apple iOS operation system : iOS 5.0 or above Download and install application programs For Windows, Android or Apple Mac based mobile devices. - Turn on the projector and select WIFI item from main menu. You can identify the default device name Projector-xxxxxx (xxxxxx is a series ID code) and its default IP address 192.168.111.1. - Turn on the WiFi function of your mobile device and search for the device Projector-xxxxxx. - Enter the link pass word (PSK)11112222 to connect with the projector. - Open the Internet explorer program of your mobile device (like I.E.) and search the device IP address 192.168.111.1. - The program download page will be displayed. Please click the corresponding program to download it for your mobile device. For Windows users, you need to restart the PC after successful installation.

projector will be turned on. To turn off the projector, please slide the power switch to the right end again till power LED is off.If you just want to turn off the projector temporarily, press the power button on the remote controller to shut down the projector light for saving power. To light up the projector, press the power button again.

2.5 Adjusting the focus Adjust the focus by using the focus wheel to get a sharp and clear picture.

2.6 Install the WiFi application programs To display contents from your mobile devices like smart phone, tablet PC or notebook PC with the projector, you need to install their corresponding application programs first.

EZ View program is designed for Windows based or Mac OS based notebook PC. EZ View program is designed for Android based or iOS based smart phones and tablet PCs.

Before installing the program, please check if your mobile device meets the operation system requirement of EZ View as below.

EZ View program - Windows operation system : Windows XP/Vista/7 (Note: Audio function is NOT supported for Windows 7.

3.1.3 Play music Use the arrow keys to select Music item and the memory device (SD/TF or USB disk). And follow the file navigator to select the target music file. This projector supports mp3, wma, ogg, wav music formats. When playing music, you can use the keys on the projector or remote controller to select music file, pause or play the music or adjust the volume. From Setting item on the main menu, you can select playing single music or sequence music.

3.1.4 Play video Use the arrow keys to select Video item and the memory device (SD/TF or USB disk). And follow the file navigator to select target video file. This projector supports the most popular video formats like MPEG1/2/4,

3.1.2 Project MS Office and PDF documents - Play document files like MS Word, Excel, PowerPoint and Adobe PDF from USB drive or Micro SD card Use the arrow keys and OK key on the remote controller to select the OFFICE icon on main menu and then the file source (USB drive or Micro SD card). Choice the target file from the displayed file list to project out. See the supported list of MS Office files Some functions are available for viewing the projected document and they can only be executed by the remote controller. The function keys are defined as below Zoom in Zoom out Scroll up Scroll down Move to right Move to left Last page Next page

Or click Refresh to search the available router again. - Now the Client Mode is setup completely. - Press return key to exit. The mobile devices will be able to go through this projector to access Internet. Different WiFi devices may use different encryption way. If the screen as right side is displayed when you link any mobile device, please do following to build the connection. Format: Select ASCII or HEX16 (refer to the user manual of this mobile device). INDEX: Select 1 PSK: Enter the assigned PSK code.

3.2.3 Project from Windows-based Notebook PCs Make sure EZ WiFi program has been installed on your Notebook PC first. - Turn on this projector and go to EZ View. - Turn on WiFi function on your Notebook PC. - Open EZ View program. It will search and link this projector

Client (Internet access) mode: Allow the mobile devices to connect Internet for displaying the web contents (likeYoutube) from the projector wirelessly. In Client mode, the projector must connect to an accessible WiFi router which linked to Internet.

Follow the steps below to setup Client mode. - Select WiFi DISPLAY item from main menu - Click Right key to move to WiFi setting page - Click Right key again to move to Router setting page - Select ON and press OK to turn on Client Mode. The Router setting page will list the available WiFi devices - Use Down key to select the router to be connected and click OK to confirm it. Then enter the pass key of this router in the PSK column and click OK.

OK to confirm your selection. - Press Left key to go back to WiFi Display page

3.2.2 Select WiFi connection mode This projector can be set up in two WiFi connection modes. AP (Pear-to-pear) mode: This is the default mode. It allows the mobile devices to download the application programs from this projector or to project the multimedia contents from the projector wirelessly.

H264, WMV, RMVB with up to 1080p resolution. Please refer to the Chapter 5 Specifications for details. When playing video, you can use the keys on the projector or remote controller to select video file, fast forward or backward, pause/play video, stop play, or adjust the volume. From Setting item on the main menu, you can select display ratio (original size or full screen), or playing single or sequence video.

3.2 Play contents from mobile devices by WiFi connection Go to main menu and select WIFI DISPLAY item 3.2.1 Configure WiFi connection - Reset the device name and connection pass word (if needed) The default device name and link pass word (PSK) are Projector-xxxxxx (xxxxxx is a series ID code) and 11112222. You may reset them from WIFI DISPLAY page. - Click WIFI DISPLAY item and then press right key to open WiFi setting page. - Use Up/Down key to select Device name or PSK (pass word) item and press OK to reset it. - Use the on-screen key board and arrow keys on remote controller to enter the new setting. - Press OK to confirm each selected character or number and press EXIT to close the on-screen key board. - Use Down key to select to save the new Device name /PSK settings or X to clean the SSID/PSK table for esetting and press

- EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs.

4. Charging your mobile devices The internal battery of the projector can not only be used for projection, but also charge your mobile device for emergency. - Please turn off the projector and switch the power switch to the Charger position before charging your mobile device. - Plug bundled USB cable to both end of micro USB DC-in port of your mobile phone and DC-OUT USB port of the projector. This is for emergent charging and may not be able to charge your mobile device to be 100% power level. The charger LED indicator

Note: Splitter display feature only supports playing photos. - Select the function from scroll bar or pull down menu. 3.2.5 Projecting from Apple iOS based smart phones or tablet PCs (like iPhones or iPads) - Make sure EZ View program installed first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function of the mobile device and link to this projector. - Open EZ View program - EZ View program provides document display, hoto display, Internet access, Dropbox display, Live camera, video display, and splitter display (up to 4 access devices)/On-screen sketch.

3.2.6 Projecting from Mac OS-based Notebook PCs Make sure EZ View program has been installed on your Mac Notebook PC first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function on your Notebook PC. - Open EZ View program and it will search and link this projector automatically.

automatically. - EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs. Splitter display: allow up to 4 PCs to project screen from the projector at the same time. But playing video contents are not supported. Mirror display: the projector will project the same screen as the PC does. Extend Mode: the projector works as a 2nd monitor to extend the screen width of the PC. 3.2.4 Project from Android

based smart phones or tablet PCs Make sure EZ View program

has been installed first. - Turn on the projector and open WiFi Display page. - Turn on WiFi function of the mobile device and link

to this projector. - Open EZ View program from your mobile device. - EZ View program provides document display, photo display, Internet access, Live camera, video display, and splitter display (up to 4 access devices)/on-screen sketch functions for your needs.

Menu Button

Mute Button

Standby Button

VOL -

VOL +

Exit Button

Play/Pause ButtonStop ButtonMove NextMove Previous

Fast Forward ButtonFast Backward Button

OK ButtonUp Button

Down Button

Right ButtonLeft Button

Remote controller

1.3 Remote controller

4 - Plug the AC power adapter into the DC-IN jack of the projector, and connect the other end to the power source. or - Connect the small end of the supplied USB cable to the USB port of the device, and the large end to a powered PC. Make sure the projector is powered off. 2.2 Plug in the WiFi USB dongle To enable the WiFi function, please plug the bundled WiFi USB dongle into the WiFi/USB port on the device. WiFi LED indicator: - LED light is on when WiFi function is enabled. - LED light is flashing when WiFi function is active. 2.3 Insert a micro SD card - Hold the micro SD card by the edges and gently insert it into the slot until it reached the bottom of the slot. - To remove the memory card, gently push the top edge of the card inwards and it will pop up slightly, then pull the card out of the slot. 2.4 Turn on the projector Slide the power switch to the right end. Hold it till power LED is on, then the

1.4 Package contents - WiFi mini projector - WiFi USB dongle - Micro USB charger cable - Power adapter - Remote controller - Users manual

2. Getting started 2.1 Charging the battery The internal battery of the projector may not be fully charged for the first time. You can charge the battery by the following two ways:

3.1.1 Playback photo Use the arrow keys to select Photoitem and the memory device (SD/TF or USB disk). And follow the file navigator to select target photo file. This projector supports *.jpg, *.jpeg, and *.bmp image formats. When displaying a photo, press OK key on the remotecontroller to active the function bar with following functions. Rotate - Enlarge Last photo Next photo Slideshow Erase Copy Exit You also can use the left and right keys on the projector or remote controller to forward and backward the displayed photo. From Setting item on the main menu, you can active slideshow function, select display ratio (original size or full screen), or slideshow duration.

For Apple iOS based iPhone or iPad devices - Please go to Apple Store to search EZ-Display and install in your iPhone or iPad device.

3. Functions and operations There are operation icons on main menu,WIFI DISPLAY, PHOTO,MUSIC,VIDEOand SETTING.

3.1 Playback the contents from the inserted micro SD card or connected USB storage device. When turning on the projector, you can use the bundled remote controller or arrow keys on the device to select the play items or make system setup. To make system setup, go to SETTING on main menu and select System Setup where you can select the display language, view the system version and reset to factory default settings. Please be noted that the WiFi USB dongle should be connected first when making setting reset.

- Apple Mac operation system : Mac OS 10.7 or later EZ View program - Android operation system : Android ICS 4.0 or above - Apple iOS operation system : iOS 5.0 or above Download and install application programs For Windows, Android or Apple Mac based mobile devices. - Turn on the projector and select WIFI item from main menu. You can identify the default device name Projector-xxxxxx (xxxxxx is a series ID code) and its default IP address 192.168.111.1. - Turn on the WiFi function of your mobile device and search for the device Projector-xxxxxx. - Enter the link pass word (PSK)11112222 to connect with the projector. - Open the Internet explorer program of your mobile device (like I.E.) and search the device IP address 192.168.111.1. - The program download page will be displayed. Please click the corresponding program to download it for your mobile device. For Windows users, you need to restart the PC after successful installation.

projector will be turned on. To turn off the projector, please slide the power switch to the right end again till power LED is off.If you just want to turn off the projector temporarily, press the power button on the remote controller to shut down the projector light for saving power. To light up the projector, press the power button again.

2.5 Adjusting the focus Adjust the focus by using the focus wheel to get a sharp and clear picture.

2.6 Install the WiFi application programs To display contents from your mobile devices like smart phone, tablet PC or notebook PC with the projector, you need to install their corresponding application programs first.

EZ View program is designed for Windows based or Mac OS based notebook PC. EZ View program is designed for Android based or iOS based smart phones and tablet PCs.

Before installing the program, please check if your mobile device meets the operation system requirement of EZ View as below.

EZ View program - Windows operation system : Windows XP/Vista/7 (Note: Audio function is NOT supported for Windows 7.

3.1.3 Play music Use the arrow keys to select Music item and the memory device (SD/TF or USB disk). And follow the file navigator to select the target music file. This projector supports mp3, wma, ogg, wav music formats. When playing music, you can use the keys on the projector or remote controller to select music file, pause or play the music or adjust the volume. From Setting item on the main menu, you can select playing single music or sequence music.

3.1.4 Play video Use the arrow keys to select Video item and the memory device (SD/TF or USB disk). And follow the file navigator to select target video file. This projector supports the most popular video formats like MPEG1/2/4,

3.1.2 Project MS Office and PDF documents - Play document files like MS Word, Excel, PowerPoint and Adobe PDF from USB drive or Micro SD card Use the arrow keys and OK key on the remote controller to select the OFFICE icon on main menu and then the file source (USB drive or Micro SD card). Choice the target file from the displayed file list to project out. See the supported list of MS Office files Some functions are available for viewing the projected document and they can only be executed by the remote controller. The function keys are defined as below Zoom in Zoom out Scroll up Scroll down Move to right Move to left Last page Next page

Or click Refresh to search the available router again. - Now the Client Mode is setup completely. - Press return key to exit. The mobile devices will be able to go through this projector to access Internet. Different WiFi devices may use different encryption way. If the screen as right side is displayed when you link any mobile device, please do following to build the connection. Format: Select ASCII or HEX16 (refer to the user manual of this mobile device). INDEX: Select 1 PSK: Enter the assigned PSK code.

3.2.3 Project from Windows-based Notebook PCs Make sure EZ WiFi program has been installed on your Notebook PC first. - Turn on this projector and go to EZ View. - Turn on WiFi function on your Notebook PC. - Open EZ View program. It will search and link this projector

Client (Internet access) mode: Allow the mobile devices to connect Internet for displaying the web contents (likeYoutube) from the projector wirelessly. In Client mode, the projector must connect to an accessible WiFi router which linked to Internet.

Follow the steps below to setup Client mode. - Select WiFi DISPLAY item from main menu - Click Right key to move to WiFi setting page - Click Right key again to move to Router setting page - Select ON and press OK to turn on Client Mode. The Router setting page will list the available WiFi devices - Use Down key to select the router to be connected and click OK to confirm it. Then enter the pass key of this router in the PSK column and click OK.

OK to confirm your selection. - Press Left key to go back to WiFi Display page

3.2.2 Select WiFi connection mode This projector can be set up in two WiFi connection modes. AP (Pear-to-pear) mode: This is the default mode. It allows the mobile devices to download the application programs from this projector or to project the multimedia contents from the projector wirelessly.

H264, WMV, RMVB with up to 1080p resolution. Please refer to the Chapter 5 Specifications for details. When playing video, you can use the keys on the projector or remote controller to select video file, fast forward or backward, pause/play video, stop play, or adjust the volume. From Setting item on the main menu, you can select display ratio (original size or full screen), or playing single or sequence video.

3.2 Play contents from mobile devices by WiFi connection Go to main menu and select WIFI DISPLAY item 3.2.1 Configure WiFi connection - Reset the device name and connection pass word (if needed) The default device name and link pass word (PSK) are Projector-xxxxxx (xxxxxx is a series ID code) and 11112222. You may reset them from WIFI DISPLAY page. - Click WIFI DISPLAY item and then press right key to open WiFi setting page. - Use Up/Down key to select Device name or PSK (pass word) item and press OK to reset it. - Use the on-screen key board and arrow keys on remote controller to enter the new setting. - Press OK to confirm each selected character or number and press EXIT to close the on-screen key board. - Use Down key to select to save the new Device name /PSK settings or X to clean the SSID/PSK table for esetting and press

- EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs.

4. Charging your mobile devices The internal battery of the projector can not only be used for projection, but also charge your mobile device for emergency. - Please turn off the projector and switch the power switch to the Charger position before charging your mobile device. - Plug bundled USB cable to both end of micro USB DC-in port of your mobile phone and DC-OUT USB port of the projector. This is for emergent charging and may not be able to charge your mobile device to be 100% power level. The charger LED indicator

Note: Splitter display feature only supports playing photos. - Select the function from scroll bar or pull down menu. 3.2.5 Projecting from Apple iOS based smart phones or tablet PCs (like iPhones or iPads) - Make sure EZ View program installed first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function of the mobile device and link to this projector. - Open EZ View program - EZ View program provides document display, hoto display, Internet access, Dropbox display, Live camera, video display, and splitter display (up to 4 access devices)/On-screen sketch.

3.2.6 Projecting from Mac OS-based Notebook PCs Make sure EZ View program has been installed on your Mac Notebook PC first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function on your Notebook PC. - Open EZ View program and it will search and link this projector automatically.

automatically. - EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs. Splitter display: allow up to 4 PCs to project screen from the projector at the same time. But playing video contents are not supported. Mirror display: the projector will project the same screen as the PC does. Extend Mode: the projector works as a 2nd monitor to extend the screen width of the PC. 3.2.4 Project from Android

based smart phones or tablet PCs Make sure EZ View program

has been installed first. - Turn on the projector and open WiFi Display page. - Turn on WiFi function of the mobile device and link

to this projector. - Open EZ View program from your mobile device. - EZ View program provides document display, photo display, Internet access, Live camera, video display, and splitter display (up to 4 access devices)/on-screen sketch functions for your needs.

5 - Plug the AC power adapter into the DC-IN jack of the projector, and connect the other end to the power source. or - Connect the small end of the supplied USB cable to the USB port of the device, and the large end to a powered PC. Make sure the projector is powered off. 2.2 Plug in the WiFi USB dongle To enable the WiFi function, please plug the bundled WiFi USB dongle into the WiFi/USB port on the device. WiFi LED indicator: - LED light is on when WiFi function is enabled. - LED light is flashing when WiFi function is active. 2.3 Insert a micro SD card - Hold the micro SD card by the edges and gently insert it into the slot until it reached the bottom of the slot. - To remove the memory card, gently push the top edge of the card inwards and it will pop up slightly, then pull the card out of the slot. 2.4 Turn on the projector Slide the power switch to the right end. Hold it till power LED is on, then the

1.4 Package contents - WiFi mini projector - WiFi USB dongle - Micro USB charger cable - Power adapter - Remote controller - Users manual

2. Getting started 2.1 Charging the battery The internal battery of the projector may not be fully charged for the first time. You can charge the battery by the following two ways:

3.1.1 Playback photo Use the arrow keys to select Photoitem and the memory device (SD/TF or USB disk). And follow the file navigator to select target photo file. This projector supports *.jpg, *.jpeg, and *.bmp image formats. When displaying a photo, press OK key on the remotecontroller to active the function bar with following functions. Rotate - Enlarge Last photo Next photo Slideshow Erase Copy Exit You also can use the left and right keys on the projector or remote controller to forward and backward the displayed photo. From Setting item on the main menu, you can active slideshow function, select display ratio (original size or full screen), or slideshow duration.

For Apple iOS based iPhone or iPad devices - Please go to Apple Store to search EZ-Display and install in your iPhone or iPad device.

3. Functions and operations There are operation icons on main menu,WIFI DISPLAY, PHOTO,MUSIC,VIDEOand SETTING.

3.1 Playback the contents from the inserted micro SD card or connected USB storage device. When turning on the projector, you can use the bundled remote controller or arrow keys on the device to select the play items or make system setup. To make system setup, go to SETTING on main menu and select System Setup where you can select the display language, view the system version and reset to factory default settings. Please be noted that the WiFi USB dongle should be connected first when making setting reset.

- Apple Mac operation system : Mac OS 10.7 or later EZ View program - Android operation system : Android ICS 4.0 or above - Apple iOS operation system : iOS 5.0 or above Download and install application programs For Windows, Android or Apple Mac based mobile devices. - Turn on the projector and select WIFI item from main menu. You can identify the default device name Projector-xxxxxx (xxxxxx is a series ID code) and its default IP address 192.168.111.1. - Turn on the WiFi function of your mobile device and search for the device Projector-xxxxxx. - Enter the link pass word (PSK)11112222 to connect with the projector. - Open the Internet explorer program of your mobile device (like I.E.) and search the device IP address 192.168.111.1. - The program download page will be displayed. Please click the corresponding program to download it for your mobile device. For Windows users, you need to restart the PC after successful installation.

projector will be turned on. To turn off the projector, please slide the power switch to the right end again till power LED is off.If you just want to turn off the projector temporarily, press the power button on the remote controller to shut down the projector light for saving power. To light up the projector, press the power button again.

2.5 Adjusting the focus Adjust the focus by using the focus wheel to get a sharp and clear picture.

2.6 Install the WiFi application programs To display contents from your mobile devices like smart phone, tablet PC or notebook PC with the projector, you need to install their corresponding application programs first.

EZ View program is designed for Windows based or Mac OS based notebook PC. EZ View program is designed for Android based or iOS based smart phones and tablet PCs.

Before installing the program, please check if your mobile device meets the operation system requirement of EZ View as below.

EZ View program - Windows operation system : Windows XP/Vista/7 (Note: Audio function is NOT supported for Windows 7.

3.1.3 Play music Use the arrow keys to select Music item and the memory device (SD/TF or USB disk). And follow the file navigator to select the target music file. This projector supports mp3, wma, ogg, wav music formats. When playing music, you can use the keys on the projector or remote controller to select music file, pause or play the music or adjust the volume. From Setting item on the main menu, you can select playing single music or sequence music.

3.1.4 Play video Use the arrow keys to select Video item and the memory device (SD/TF or USB disk). And follow the file navigator to select target video file. This projector supports the most popular video formats like MPEG1/2/4,

3.1.2 Project MS Office and PDF documents - Play document files like MS Word, Excel, PowerPoint and Adobe PDF from USB drive or Micro SD card Use the arrow keys and OK key on the remote controller to select the OFFICE icon on main menu and then the file source (USB drive or Micro SD card). Choice the target file from the displayed file list to project out. See the supported list of MS Office files Some functions are available for viewing the projected document and they can only be executed by the remote controller. The function keys are defined as below Zoom in Zoom out Scroll up Scroll down Move to right Move to left Last page Next page

Or click Refresh to search the available router again. - Now the Client Mode is setup completely. - Press return key to exit. The mobile devices will be able to go through this projector to access Internet. Different WiFi devices may use different encryption way. If the screen as right side is displayed when you link any mobile device, please do following to build the connection. Format: Select ASCII or HEX16 (refer to the user manual of this mobile device). INDEX: Select 1 PSK: Enter the assigned PSK code.

3.2.3 Project from Windows-based Notebook PCs Make sure EZ WiFi program has been installed on your Notebook PC first. - Turn on this projector and go to EZ View. - Turn on WiFi function on your Notebook PC. - Open EZ View program. It will search and link this projector

Client (Internet access) mode: Allow the mobile devices to connect Internet for displaying the web contents (likeYoutube) from the projector wirelessly. In Client mode, the projector must connect to an accessible WiFi router which linked to Internet.

Follow the steps below to setup Client mode. - Select WiFi DISPLAY item from main menu - Click Right key to move to WiFi setting page - Click Right key again to move to Router setting page - Select ON and press OK to turn on Client Mode. The Router setting page will list the available WiFi devices - Use Down key to select the router to be connected and click OK to confirm it. Then enter the pass key of this router in the PSK column and click OK.

OK to confirm your selection. - Press Left key to go back to WiFi Display page

3.2.2 Select WiFi connection mode This projector can be set up in two WiFi connection modes. AP (Pear-to-pear) mode: This is the default mode. It allows the mobile devices to download the application programs from this projector or to project the multimedia contents from the projector wirelessly.

H264, WMV, RMVB with up to 1080p resolution. Please refer to the Chapter 5 Specifications for details. When playing video, you can use the keys on the projector or remote controller to select video file, fast forward or backward, pause/play video, stop play, or adjust the volume. From Setting item on the main menu, you can select display ratio (original size or full screen), or playing single or sequence video.

3.2 Play contents from mobile devices by WiFi connection Go to main menu and select WIFI DISPLAY item 3.2.1 Configure WiFi connection - Reset the device name and connection pass word (if needed) The default device name and link pass word (PSK) are Projector-xxxxxx (xxxxxx is a series ID code) and 11112222. You may reset them from WIFI DISPLAY page. - Click WIFI DISPLAY item and then press right key to open WiFi setting page. - Use Up/Down key to select Device name or PSK (pass word) item and press OK to reset it. - Use the on-screen key board and arrow keys on remote controller to enter the new setting. - Press OK to confirm each selected character or number and press EXIT to close the on-screen key board. - Use Down key to select to save the new Device name /PSK settings or X to clean the SSID/PSK table for esetting and press

- EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs.

4. Charging your mobile devices The internal battery of the projector can not only be used for projection, but also charge your mobile device for emergency. - Please turn off the projector and switch the power switch to the Charger position before charging your mobile device. - Plug bundled USB cable to both end of micro USB DC-in port of your mobile phone and DC-OUT USB port of the projector. This is for emergent charging and may not be able to charge your mobile device to be 100% power level. The charger LED indicator

Note: Splitter display feature only supports playing photos. - Select the function from scroll bar or pull down menu. 3.2.5 Projecting from Apple iOS based smart phones or tablet PCs (like iPhones or iPads) - Make sure EZ View program installed first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function of the mobile device and link to this projector. - Open EZ View program - EZ View program provides document display, hoto display, Internet access, Dropbox display, Live camera, video display, and splitter display (up to 4 access devices)/On-screen sketch.

3.2.6 Projecting from Mac OS-based Notebook PCs Make sure EZ View program has been installed on your Mac Notebook PC first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function on your Notebook PC. - Open EZ View program and it will search and link this projector automatically.

automatically. - EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs. Splitter display: allow up to 4 PCs to project screen from the projector at the same time. But playing video contents are not supported. Mirror display: the projector will project the same screen as the PC does. Extend Mode: the projector works as a 2nd monitor to extend the screen width of the PC. 3.2.4 Project from Android

based smart phones or tablet PCs Make sure EZ View program

has been installed first. - Turn on the projector and open WiFi Display page. - Turn on WiFi function of the mobile device and link

to this projector. - Open EZ View program from your mobile device. - EZ View program provides document display, photo display, Internet access, Live camera, video display, and splitter display (up to 4 access devices)/on-screen sketch functions for your needs.

6 - Plug the AC power adapter into the DC-IN jack of the projector, and connect the other end to the power source. or - Connect the small end of the supplied USB cable to the USB port of the device, and the large end to a powered PC. Make sure the projector is powered off. 2.2 Plug in the WiFi USB dongle To enable the WiFi function, please plug the bundled WiFi USB dongle into the WiFi/USB port on the device. WiFi LED indicator: - LED light is on when WiFi function is enabled. - LED light is flashing when WiFi function is active. 2.3 Insert a micro SD card - Hold the micro SD card by the edges and gently insert it into the slot until it reached the bottom of the slot. - To remove the memory card, gently push the top edge of the card inwards and it will pop up slightly, then pull the card out of the slot. 2.4 Turn on the projector Slide the power switch to the right end. Hold it till power LED is on, then the

1.4 Package contents - WiFi mini projector - WiFi USB dongle - Micro USB charger cable - Power adapter - Remote controller - Users manual

2. Getting started 2.1 Charging the battery The internal battery of the projector may not be fully charged for the first time. You can charge the battery by the following two ways:

3.1.1 Playback photo Use the arrow keys to select Photoitem and the memory device (SD/TF or USB disk). And follow the file navigator to select target photo file. This projector supports *.jpg, *.jpeg, and *.bmp image formats. When displaying a photo, press OK key on the remotecontroller to active the function bar with following functions. Rotate - Enlarge Last photo Next photo Slideshow Erase Copy Exit You also can use the left and right keys on the projector or remote controller to forward and backward the displayed photo. From Setting item on the main menu, you can active slideshow function, select display ratio (original size or full screen), or slideshow duration.

For Apple iOS based iPhone or iPad devices - Please go to Apple Store to search EZ-Display and install in your iPhone or iPad device.

3. Functions and operations There are operation icons on main menu,WIFI DISPLAY, PHOTO,MUSIC,VIDEOand SETTING.

3.1 Playback the contents from the inserted micro SD card or connected USB storage device. When turning on the projector, you can use the bundled remote controller or arrow keys on the device to select the play items or make system setup. To make system setup, go to SETTING on main menu and select System Setup where you can select the display language, view the system version and reset to factory default settings. Please be noted that the WiFi USB dongle should be connected first when making setting reset.

- Apple Mac operation system : Mac OS 10.7 or later EZ View program - Android operation system : Android ICS 4.0 or above - Apple iOS operation system : iOS 5.0 or above Download and install application programs For Windows, Android or Apple Mac based mobile devices. - Turn on the projector and select WIFI item from main menu. You can identify the default device name Projector-xxxxxx (xxxxxx is a series ID code) and its default IP address 192.168.111.1. - Turn on the WiFi function of your mobile device and search for the device Projector-xxxxxx. - Enter the link pass word (PSK)11112222 to connect with the projector. - Open the Internet explorer program of your mobile device (like I.E.) and search the device IP address 192.168.111.1. - The program download page will be displayed. Please click the corresponding program to download it for your mobile device. For Windows users, you need to restart the PC after successful installation.

projector will be turned on. To turn off the projector, please slide the power switch to the right end again till power LED is off.If you just want to turn off the projector temporarily, press the power button on the remote controller to shut down the projector light for saving power. To light up the projector, press the power button again.

2.5 Adjusting the focus Adjust the focus by using the focus wheel to get a sharp and clear picture.

2.6 Install the WiFi application programs To display contents from your mobile devices like smart phone, tablet PC or notebook PC with the projector, you need to install their corresponding application programs first.

EZ View program is designed for Windows based or Mac OS based notebook PC. EZ View program is designed for Android based or iOS based smart phones and tablet PCs.

Before installing the program, please check if your mobile device meets the operation system requirement of EZ View as below.

EZ View program - Windows operation system : Windows XP/Vista/7 (Note: Audio function is NOT supported for Windows 7.

3.1.3 Play music Use the arrow keys to select Music item and the memory device (SD/TF or USB disk). And follow the file navigator to select the target music file. This projector supports mp3, wma, ogg, wav music formats. When playing music, you can use the keys on the projector or remote controller to select music file, pause or play the music or adjust the volume. From Setting item on the main menu, you can select playing single music or sequence music.

3.1.4 Play video Use the arrow keys to select Video item and the memory device (SD/TF or USB disk). And follow the file navigator to select target video file. This projector supports the most popular video formats like MPEG1/2/4,

3.1.2 Project MS Office and PDF documents - Play document files like MS Word, Excel, PowerPoint and Adobe PDF from USB drive or Micro SD card Use the arrow keys and OK key on the remote controller to select the OFFICE icon on main menu and then the file source (USB drive or Micro SD card). Choice the target file from the displayed file list to project out. See the supported list of MS Office files Some functions are available for viewing the projected document and they can only be executed by the remote controller. The function keys are defined as below Zoom in Zoom out Scroll up Scroll down Move to right Move to left Last page Next page

Or click Refresh to search the available router again. - Now the Client Mode is setup completely. - Press return key to exit. The mobile devices will be able to go through this projector to access Internet. Different WiFi devices may use different encryption way. If the screen as right side is displayed when you link any mobile device, please do following to build the connection. Format: Select ASCII or HEX16 (refer to the user manual of this mobile device). INDEX: Select 1 PSK: Enter the assigned PSK code.

3.2.3 Project from Windows-based Notebook PCs Make sure EZ WiFi program has been installed on your Notebook PC first. - Turn on this projector and go to EZ View. - Turn on WiFi function on your Notebook PC. - Open EZ View program. It will search and link this projector

Client (Internet access) mode: Allow the mobile devices to connect Internet for displaying the web contents (likeYoutube) from the projector wirelessly. In Client mode, the projector must connect to an accessible WiFi router which linked to Internet.

Follow the steps below to setup Client mode. - Select WiFi DISPLAY item from main menu - Click Right key to move to WiFi setting page - Click Right key again to move to Router setting page - Select ON and press OK to turn on Client Mode. The Router setting page will list the available WiFi devices - Use Down key to select the router to be connected and click OK to confirm it. Then enter the pass key of this router in the PSK column and click OK.

OK to confirm your selection. - Press Left key to go back to WiFi Display page

3.2.2 Select WiFi connection mode This projector can be set up in two WiFi connection modes. AP (Pear-to-pear) mode: This is the default mode. It allows the mobile devices to download the application programs from this projector or to project the multimedia contents from the projector wirelessly.

H264, WMV, RMVB with up to 1080p resolution. Please refer to the Chapter 5 Specifications for details. When playing video, you can use the keys on the projector or remote controller to select video file, fast forward or backward, pause/play video, stop play, or adjust the volume. From Setting item on the main menu, you can select display ratio (original size or full screen), or playing single or sequence video.

3.2 Play contents from mobile devices by WiFi connection Go to main menu and select WIFI DISPLAY item 3.2.1 Configure WiFi connection - Reset the device name and connection pass word (if needed) The default device name and link pass word (PSK) are Projector-xxxxxx (xxxxxx is a series ID code) and 11112222. You may reset them from WIFI DISPLAY page. - Click WIFI DISPLAY item and then press right key to open WiFi setting page. - Use Up/Down key to select Device name or PSK (pass word) item and press OK to reset it. - Use the on-screen key board and arrow keys on remote controller to enter the new setting. - Press OK to confirm each selected character or number and press EXIT to close the on-screen key board. - Use Down key to select to save the new Device name /PSK settings or X to clean the SSID/PSK table for esetting and press

- EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs.

4. Charging your mobile devices The internal battery of the projector can not only be used for projection, but also charge your mobile device for emergency. - Please turn off the projector and switch the power switch to the Charger position before charging your mobile device. - Plug bundled USB cable to both end of micro USB DC-in port of your mobile phone and DC-OUT USB port of the projector. This is for emergent charging and may not be able to charge your mobile device to be 100% power level. The charger LED indicator

Note: Splitter display feature only supports playing photos. - Select the function from scroll bar or pull down menu. 3.2.5 Projecting from Apple iOS based smart phones or tablet PCs (like iPhones or iPads) - Make sure EZ View program installed first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function of the mobile device and link to this projector. - Open EZ View program - EZ View program provides document display, hoto display, Internet access, Dropbox display, Live camera, video display, and splitter display (up to 4 access devices)/On-screen sketch.

3.2.6 Projecting from Mac OS-based Notebook PCs Make sure EZ View program has been installed on your Mac Notebook PC first. - Turn on this projector and go to WiFi Display page. - Turn on WiFi function on your Notebook PC. - Open EZ View program and it will search and link this projector automatically.

automatically. - EZ View program provides splitter display, Mirror/Extend display and audio on/off options for your needs. Splitter display: allow up to 4 PCs to project screen from the projector at the same time. But playing video contents are not supported. Mirror display: the projector will project the same screen as the PC does. Extend Mode: the projector works as a 2nd monitor to extend the screen width of the PC. 3.2.4 Project from Android

based smart phones or tablet PCs Make sure EZ View program

has been installed first. - Turn on the projector and open WiFi Display page. - Turn on WiFi function of the mobile device and link

to this projector. - Open EZ View program from your mobile device. - EZ View program provides document display, photo display, Internet access, Live camera, video display, and splitter display (up to 4 access devices)/on-screen sketch functions for your needs.

7 - Plug the AC power adapter into the DC-IN jack of the projector, and connect the other end to the power source. or - Connect the small end of the supplied USB cable to the USB port of the device, and the large end to a powered PC. Make sure the projector is powered off. 2.2 Plug in the WiFi USB dongle To enable the WiFi function, please plug the bundled WiFi USB dongle into the WiFi/USB port on the device. WiFi LED indicator: - LED light is on when WiFi function is enabled. - LED light is flashing when WiFi function is active. 2.3 Insert a micro SD card - Hold the micro SD card by the edges and gently insert it into the slot until it reached the bottom of the slot. - To remove the memory card, gently push the top edge of the card inwards and it will pop up slightly, then pull the card out of the slot. 2.4 Turn on the projector Slide the power switch to the right end. Hold it till power LED is on, then the

1.4 Package contents - WiFi mini projector - WiFi USB dongle - Micro USB charger cable - Power adapter - Remote controller - Users manual

2. Getting started 2.1 Charging the battery The internal battery of the projector may not be fully charged for the first time. You can charge the battery by the following two ways:

3.1.1 Playback photo Use the arrow keys to select Photoitem and the memory device (SD/TF or USB disk). And follow the file navigator to select target photo file. This projector supports *.jpg, *.jpeg, and *.bmp image formats. When displaying a photo, press OK key on the remotecontroller to active the function bar with following functions. Rotate - Enlarge Last photo Next photo Slideshow Erase Copy Exit You also can use the left and right keys on the projector or remote controller to forward and backward the displayed photo. From Setting item on the main menu, you can active slideshow function, select display ratio (original size or full screen), or slideshow duration.

For Apple iOS based iPhone or iPad devices - Please go to Apple Store to search EZ-Display and install in your iPhone or iPad device.

3. Functions and operations There are operation icons on main menu,WIFI DISPLAY, PHOTO,MUSIC,VIDEOand SETTING.

3.1 Playback the contents from the inserted micro SD card or connected USB storage device. When turning on the projector, you can use the bundled remote controller or arrow keys on the device to select the play items or make system setup. To make system setup, go to SETTING on main menu and select System Setup where you can select the display language, view the system version and reset to factory default settings. Please be noted that the WiFi USB dongle should be connected first when making setting reset.

- Apple Mac operation system : Mac OS 10.7 or later EZ View program - Android operation system : Android ICS 4.0 or above - Apple iOS operation system : iOS 5.0 or above Download and install application programs For Windows, Android or Apple Mac based mobile devices. - Turn on the projector and select WIFI item from main menu. You can identify the default device name Projector-xxxxxx (xxxxxx is a series ID code) and its default IP address 192.168.111.1. - Turn on the WiFi function of your mobile device and search for the device Projector-xxxxxx. - Enter the link pass word (PSK)11112222 to connect with the projector. - Open the Internet explorer program of your mobile device (like I.E.) and search the device IP address 192.168.111.1. - The program download page will be displayed. Please click the corresponding program to download it for your mobile device. For Windows users, you need to restart the PC after successful installation.

projector will be turned on. To turn off the projector, please slide the power switch to the right end again till power LED is off.If you just want to turn off the projector temporarily, press the power button on the remote controller to shut down the projector light for saving power. To light up the projector, press the power button again.

2.5 Adjusting the focus Adjust the focus by using the focus wheel to get a sharp and clear picture.

2.6 Install the WiFi application programs To display contents from your mobile devices like smart phone, tablet PC or notebook PC with the projector, you need to install their corresponding application programs first.

EZ View program is designed for Windows based or Mac OS based notebook PC. EZ View program is designed for Android based or iOS based smart phones and tablet PCs.

Before installing the program, please check if your mobile device meets the operation system requirement of EZ View as below.

EZ View program - Windows operation system : Windows XP/Vista/7 (Note: Audio function is NOT supported for Windows 7.

3.1.3 Play music Use the arrow keys to select Music item and the memory device (SD/TF or USB disk). And follow the file navigator to select the target music file. This projector supports mp3, wma, ogg, wav music formats. When playing music, you can use the keys on the projector or remote controller to select music file, pause or play the music or adjust the volume. From Setting item on the main menu, you can select playing single music or sequence music.

3.1.4 Play video Use the arrow keys to select Video item and the memory device (SD/TF or USB disk). And follow the file navigator to select target video file. This projector supports the most popular video formats like MPEG1/2/4,

3.1.2 Project MS Office and PDF documents - Play document files like MS Word, Excel, PowerPoint and Adobe PDF from USB drive or Micro SD card Us