SONPAK

8/12/2019 SONPAK

http://slidepdf.com/reader/full/sonpak 1/3

www.thornlighting.co.uk 372

Sonpak 25/401:1

250W, 400W HPS-T E40 250W, 400W HIT E40 IP65 EN 60598 5 joules 960˚ Hotwire Ta Max: +25˚C

Discharge floodlight forgeneral area lighting.

• Choice of high pressuresodium or metal halide lampsin 250W or 400W ratings

• Robust die-cast aluminium body

and front frame• Asymmetrical reflector

• Toughened glass front

• Integral control gear

• Spill shield available forreduced glare

• Easy installation withdrop down front glassand cable entry

• Adjustable streamlined stirrupfor flexibility in mounting

•

Sealed to IP65

Materials/FinishBody and front frame: Die-castaluminium, painted black, RAL 9005Reflector: Dimpled anodisedaluminium.Lens: Tempered 4mm flat glasswith stainless steel bolts andsilicone rubber gasket.Stirrup: 4mm mild steel, polyesterpainted black, RAL 9005.

Installation/Mounting

1 glanded cable entry for 9-13mmo/d cable with 3 pole terminalblock for up to 10mm2 cables.21mm Ø knockout at rear forthrough wiring.Stirrup fixed by single bolt through21mm Ø hole. Two additional11mm Ø fixing holes at 250mmcentres. Aiming angle of floodlightaided by goniometer.

SpecificationTo specify state:Enclosed floodlight with blackaluminium body and frame housing

flat glass. Integral control gearand asymmetrical reflector for250W/400W HPS-T or250W/400W HIT lamp.Sealed to IP65.As Thorn Sonpak 25/40.

Wire guard Spill shield Louvre

Ordering Guide Supplied complete with lamp.

Lamp type Windage Weight Cat. No.& rating (m2) (kg)

HPS-T 250W 0.165 13.0 OT250T.4HPS-T 400W 0.165 13.0 OT400T.4HIT 250W 0.165 13.0 OTMH250T.4HIT 400W 0.165 13.0 OTMH400T.4

Export voltages available, refer to page 553 for details.

Attachments

Description Cat. No.Wire guard OTWGCLouvre* OTLCSpill shield for environmentally sensitive areas* OTSSCSonpak single mounting bracket (76mm Ø shaft) QCB F1

Sonpak twin stirrup version mounting bracket (76mm Ø shaft) QCB F2Sonpak triple stirrup version mounting bracket (76mm Ø shaft) QCB F3 DELTASonpak 4-way stirrup version mounting bracket (76mm Ø shaft) QCB F4 CROSS

Note that brackets above are suitable for use with QC-TC and QCZR (76mm Ø shaft) columns.* Supplied with 4 screws and washers. These attachments cannot be mounted together,one on the other.

165 420

375

535 447

238

-90° -60° -30° 0° 30° 60° 90°

900

750

600

450

300

250

0

cd/1000 lm

horizontalvertical

Cat. No. OT250T.4Lamp: 25W HPS-T

8/12/2019 SONPAK




Lamp type Windage Weight Cat. No.& rating (m2) (kg)

HPS-T (external ignitor) 70W 0.105 9.0 OT70T.4HPS-T 100W 0.105 9.0 OT100T.4HPS-T 150W 0.105 9.0 OT150T.4HIT-DE 150W 0.105 9.0 OTMH150D.4

Export voltages available, refer to page 553 for details.

Attachments

Description Cat. No.Wire guard OTWGBLouvre* OTLBSpill shield for environmentally sensitive areas* OTSSB

Pole clamp for use with 48-89mm Ø poles OHA4613Sonpak single mounting bracket (76mm Ø shaft) QCB F1Sonpak twin stirrup version mounting bracket (76mm Ø shaft) QCB F2Sonpak triple stirrup version mounting bracket (76mm Ø shaft) QCB F3 DELTASonpak 4-way stirrup version mounting bracket (76mm Ø shaft) QCB F4 CROSS

Note that brackets above are suitable for use with QC-TC and QCZR (76mm Ø shaft) columns.*Supplied with 4 screws and washers. These attachments cannot be mounted together,one on the other. See page 372 for attachments.

O U T D O OR

A R E A

F L O OD

L I GH T I N G

Sonpak 7/151:1

Discharge floodlight forgeneral area lighting.

• Choice of high pressure sodiumor double-ended metal halidelamps in a variety of wattages

• Robust die-cast aluminium

body and front frame• Asymmetrical reflector

• Toughened glass front


• Spill shield available forreduced glare (see page 372)

• Easy installation with drop downfront glass and cable entry

• Adjustable streamlined stirrupfor flexibility in mounting

• Sealed to IP65

Materials/FinishBody and front frame: Die-castaluminium, painted black,RAL 9005.Reflector: Dimpled anodisedaluminium.Lens: Tempered 4mm flat glasswith stainless steel bolts andsilicone rubber gasket.Stirrup: 3mm mild steel, polyesterpainted black, RAL 9005.

Installation/MountingOne glanded cable entry for9-13mm o/d cable with 3 poleterminal block for up to 10mm2

cables.21mm Ø knockout at rear forthrough wiring.Stirrup fixed by single boltthrough 21mm Ø hole. Twoadditional 11mm Ø fixing holesat 102mm centres, with a furthertwo 13mm Ø fixing holes at250mm centres.Aiming angle of floodlight aidedby goniometer.

SpecificationTo specify state:Enclosed floodlight with blackaluminium body and frame,housing flat glass. Integral controlgear and asymmetrical reflectorfor 70W/100W/150W HPS-Tor 150W HIT-DE lamp.Sealed to IP65.As Thorn Sonpak 7/15.

127

256

335

115

400 365

192

-90° -60° -30° 0° 30° 60° 90°

900

750

600

450

300

250

0

cd/1000 lm

horizontalvertical

Cat. No. OT150T.4Lamp: 150W HPS-T

70W HPS-T E27 (external ignitor) 100W, 150W HPS-T E40 150W HIT-DE Rx7s

IP65 EN 60598 5 joules 960˚ Hotwire Ta Max: +25˚C

8/12/2019 SONPAK



Sonpak 71:1

70W HPS-E/I clear (internal ignitor) E27 70W HIT-DE RX7s IP65 EN 60598 5 joules 960˚ Hotwire Ta Max: + 25˚C

An efficient discharge floodlightfor security applications, buildingfacades and perimeters, carparks, loading bays and precincts.

• Choice of high pressuresodium or metal halide lamps

• Easy to install

• Tough, technopolymer body

• Asymmetrical reflector

• Vandal resistant constructionwith high impact clearpolycarbonate visor


• Attachments available for poleand wall mounting

• Especially suitable for localarea lighting from lowmounting heights of 3-5m forclose offset lighting of buildings

•

Integral photocell fordusk-to-dawn operation

• Sealed to IP65

Materials/FinishBody: Technopolymer, finishedblack RAL 9005.

Visor: Clear polycarbonate.Standard reflector: Aluminium,dimpled anodised. Asymmetrical.Stirrup: 3mm mild steel paintedblack, RAL 9005.

Installation/MountingOne glanded cable entry for9-11mm o/d cable with 3 poleterminal block for up to 10mm2

cables. 21mm Ø knockout atrear for photocell or throughwiring. Stirrup fixed by singlebolt through 21mm Ø hole.Two additional 11mm Ø fixing

holes at 100mm centres, with afurther two 11mm Ø fixing holesat 180mm centres.Aiming angle of floodlight aidedby goniometer.

SpecificationTo specify state:Enclosed black technopolymer

floodlight with polycarbonatevisor/photcell. Integral controlgear and asymmetrical reflectorfor 70W HIT-DE/clearHPS-E/I lamp.Sealed to IP65.As Thorn Sonpak 7.

225

267160

320385

Louvre


Lamp type Description Weight Windage Cat. No.& rating (kg) (m2)

HPS-E/l 70W (internal ignitor) Sonpak 7 4.0 0.066 OT70E.4HPS-E/l 70W (internal ignitor) Sonpak 7 + photocel l 4.0 0.066 OTP70E.4HIT-DE 70W Sonpak 7 4.0 0.066 OTMH70D.4HIT-DE 70W Sonpak 7 + photocell 4.0 0.066 OTPMH70D.4

Export voltages available, refer to 553 for details.

Attachments

Description Cat. No.Louvre OTLAHeavy duty wall bracket allowing approx. 70° horizontal adjustment OHA 4601Mounting cap for 76mm Ø x 76mm min. depth pole or spigot OHA 4612Pole clamp for use with 48-89mm Ø poles OHA 4613

-90° -60° -30° 0° 30° 60° 90°

600

500

400

300

200

100

0

cd/1000 lm

horizontalvertical

Cat. No. OT70E.4Lamp: 70W HPS-E/1

Documents

SONPAK