DEVELOPWNTS NEW EQUIPMENT, PROCESSES, & MATERIALS Oil/Water Separation BetzDearborn Water Management Group Horsham, Pa. A new, all-organic liquid coagulant specifically developed for tough indus- trial oil/water separation applications offers a wide range of benefits, including greater oil recovery, higher quality oil for reuse, improved water clarity, better met- als removal, and lower sludge volume. BetzDearbom KlarAid polymers are more effective than conventional polymers when treating water-containing emulsified oils, colloidal material, water- soluble oils, metalworking fluids, and hydrocarbon oils. Circle 401 on the reader service card Rust Preventive Birchwood Casey Eden Prairie, Minn. Dri-Touch topcoat, an effective rust blocker, is a nontacky film that will not run off or wick off into packaging, thus maintaining an effective, long-term bar- rier against humidity and corrosion. The topcoat offers up to 1 .OoO hr of humidity protection with a 130” flash point. The sealant can be applied directly over wet surfaces. Available in two light-bodied liquid grades. Dri-Touch can be applied easily by dipping, brushing. or low-pressure spraying. Circle 402 on the reader service card Solvent Wiping System Confec Inc. Spatfanburg, SC. Contec’s SATWipes presaturated wipers are ideal for powder coating and other surface preparation applications because of their ability to reduce paint defects. The cleaning system consists of a roll of saturated wipers that are dispensed through a resealable center-pull container. Economy, Stan- dard, and Premium SATWipes are designed to make solvent wiping easier and safer while reducing waste, solvent use, and VOCs. All wipes can be saturated with a number of solvents. As a standard offering, three sizes, three low-linting wipers materials. and seven solvent blends are offered. Cus- tom products are also available. Circle 403 on the reader service card Silicone Rubber Pull Plugs Caplugs Div., Protective Closures Co. Inc. Buffalo, N. Y The SPP series silicone rubber pull plugs designed for protecting and masking parts undergoing painting, plating, powder coating anodizing, or exposure to high temperatures up to 600°F. The pull plugs are designed to provide complete and positive protection to female threaded ports and to the inside walls of holes ranging from 0.091 in. diameter to 0.335 in. and in lengths from 0.61 in. to 1 in. Circle 404 on the reader service card Coating Measurement Gauge CM1 International Elk Grove Village, 111. The CM1 100 Series is a portable full-featured gauge that packs electron- ics, probe, and back-lit display into one compact. ti&nd-held unit, which is bat- tery operated and weighs only 2.3 oz. State-of-the-art technology ensures ac- curate and repeatable measurements in both eddy-current and magnetic induc- tion models. It is easy to use with only four buttons controlling all functions. Statistics can be viewed directly on the display or downloaded to a printer via an infrared beam. Circle 405 on the reader service card Probe for Coating Thickness Gauge DeFelsko Corp. Ogdensburg, N. Y DeFelsko’s MicroProbes have been designed for measuring coating thickness on small or hard-to-reach ferrous or nonferrous surfaces. The probes are available to tit either the PosiTector 6000 or the PosiTest 1000 coating thickness gauges. The probes are available in three different configurations including 0” for deep holes. 45’ for tight ledges. and 90 for inside diameters. The 0’ probe in- cludes a removalbe Quick Release Sleeve, which easily slides on and off the probe. converting it to a stabilized con- stant pressure probe for easy alignment on small. flat, or curved parts. METAL FINISHING . JULY 1998 45

Solvent wiping system

Download PDF Report

Upload
doandien
View
214
Download
0

Embed Size (px)

Citation preview

DEVELOPWNTS NEW EQUIPMENT, PROCESSES, & MATERIALS

Oil/Water Separation BetzDearborn Water Management Group Horsham, Pa.

A new, all-organic liquid coagulant specifically developed for tough indus- trial oil/water separation applications offers a wide range of benefits, including greater oil recovery, higher quality oil for reuse, improved water clarity, better met- als removal, and lower sludge volume. BetzDearbom KlarAid polymers are more effective than conventional polymers when treating water-containing emulsified oils, colloidal material, water- soluble oils, metalworking fluids, and hydrocarbon oils.

Circle 401 on the reader service card

Rust Preventive Birchwood Casey Eden Prairie, Minn.

Dri-Touch topcoat, an effective rust blocker, is a nontacky film that will not run off or wick off into packaging, thus maintaining an effective, long-term bar- rier against humidity and corrosion. The topcoat offers up to 1 .OoO hr of humidity protection with a 130” flash point. The sealant can be applied directly over wet surfaces. Available in two light-bodied liquid grades. Dri-Touch can be applied easily by dipping, brushing. or low-pressure spraying.

Circle 402 on the reader service card

Solvent Wiping System Confec Inc. Spatfanburg, SC.

Contec’s SATWipes presaturated wipers are ideal for powder coating and other surface preparation applications because of their ability to reduce paint defects. The cleaning system consists of a roll of saturated wipers that are dispensed through a resealable center-pull container. Economy, Stan- dard, and Premium SATWipes are designed to make solvent wiping easier and safer while reducing waste, solvent use, and VOCs. All wipes can be saturated with a number of solvents. As a standard offering, three sizes, three low-linting wipers materials. and

seven solvent blends are offered. Cus- tom products are also available.

Circle 403 on the reader service card

Silicone Rubber Pull Plugs Caplugs Div., Protective Closures Co. Inc. Buffalo, N. Y

The SPP series silicone rubber pull plugs designed for protecting and masking parts undergoing painting, plating, powder coating anodizing, or exposure to high temperatures up to 600°F. The pull plugs are designed to provide complete and positive protection to female threaded ports and to the inside walls of holes ranging from 0.091 in. diameter to 0.335 in. and in lengths from 0.61 in. to 1 in.

Circle 404 on the reader service card

Coating Measurement Gauge CM1 In terna tional Elk Grove Village, 111.

The CM1 100 Series is a portable full-featured gauge that packs electron- ics, probe, and back-lit display into one compact. ti&nd-held unit, which is bat- tery operated and weighs only 2.3 oz. State-of-the-art technology ensures ac- curate and repeatable measurements in both eddy-current and magnetic induc- tion models. It is easy to use with only four buttons controlling all functions. Statistics can be viewed directly on the display or downloaded to a printer via an infrared beam.

Circle 405 on the reader service card

Probe for Coating Thickness Gauge DeFelsko Corp. Ogdensburg, N. Y

DeFelsko’s MicroProbes have been designed for measuring coating thickness on small or hard-to-reach ferrous or nonferrous surfaces. The probes are available to tit either the PosiTector 6000 or the PosiTest 1000 coating thickness gauges. The probes are available in three different configurations including 0” for deep holes. 45’ for tight ledges. and 90 for inside diameters. The 0’ probe in- cludes a removalbe Quick Release Sleeve, which easily slides on and off the probe. converting it to a stabilized con- stant pressure probe for easy alignment on small. flat, or curved parts.

METAL FINISHING . JULY 1998 45