Upload
ide
View
98
Download
0
Tags:
Embed Size (px)
DESCRIPTION
SMMT Type Approval Workshop. Wednesday 25 April 2012 CV Show, NEC, Birmingham. Welcome address. Tony Hopkins. Technical Manager, SMMT. Introduction to the content of the workshop Automotive legislation is continually moving and changing. - PowerPoint PPT Presentation
Citation preview
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the motor industry’ brandline are trademarks of SMMT Ltd
SMMT Type Approval Workshop
Wednesday 25 April 2012CV Show, NEC, Birmingham
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the motor industry’ brandline are trademarks of SMMT Ltd
Welcome address
Tony Hopkins. Technical Manager, SMMT
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 3
Introduction to the content of the workshop
• Automotive legislation is continually moving and changing.
• The following is to try and give you and idea of how to approve a particular type of trailer (O Category) as part of a multi-stage build process.
• The tools to assist you
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 4
AgendaTime Subject Speaker
13.45 – 14.00 Registration - Trailer Workshop refreshments
14:00 – 14:05 Welcome Tony Hopkins, Technical Manager,
SMMT
14:05 – 14:30 Explanation of 2007/46 EC Article 6 Procedures for the EC type-approval of vehicles.Step by step, single step and mixed type- approval. Option available using the Vehicle information folders in 2007/46/EC Annex 1 or Annex III part 11
Mike Protheroe, Vehicle Certification Agency (VCA).
14:30 – 14:50 SENTA Overview Tony Hopkins, Technical Manager,SMMT
14:50 – 15:15 Worked example of an ECWVTA for a Category O Trailer Mike Protheroe, Vehicle Certification Agency (VCA).
14:15 – 15:00 Questions
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 5
The current situation
For trailers of Categories O1, 2, 3 & 4 –
No requirements
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 6
Vehicle categories
• Category O1: Trailers with a maximum mass not exceeding 0,75 tonnes
• Category O2: Trailers with a maximum mass exceeding 0,75 tonnes but not exceeding 3,5 tonnes.
• Category O3: Trailers with a maximum mass exceeding 3,5 tonnes but not exceeding 10 tonnes.
• Category O4: Trailers with a maximum mass exceeding 10 tonnes.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 7
So what's happening?
For all categories of vehicle including trailers –
European Community Whole Vehicle Type Approval
EC Directive 2007/46/EC
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 8
2007/46/EC
342 Pages
21 Annex’s
Covers all vehicle categories and types
Anything up to 60+ separate directives to comply with
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 9
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 10
Type approval routes
• European Community Whole Vehicle type Approval (ECWVTA).
Full approval to register unlimited numbers of a type of vehicle within the EU
• National Small series Type Approval (NSSTA).
Approval to register a limited number of a type of vehicle within the member state issuing the approval
• Individual Vehicle Approval (IVA).
Approval of a single type of vehicle. Administered by VOSA.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 11
Conformity of production (COP)
As part of the approval process for ECWVTA andNSSTA, you will require a COP process.
• ECWVTA – Formal process
• NSSTA – An ‘approved’ process
Both ECWVTA & NSSTA will require control plans. Furtherinformation can be obtained from the Vehicle Certification Agency(VCA).
• IVA - No COP required
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 12
Trailers
Depending on the type of trailer manufactured, it is likely that the following technical requirements will need to be met:
• Rear protection device• Registration plate space• Steering effort• Braking• Radio interference• Statutory plates• Installation of lighting• Spray suppression• Safety glazing• Tyres• Masses and dimensions• Couplings• Transport of dangerous goods
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 13
Trailers
• Trailers in the UK are not registered.
• From 29th April 2012, new requirements for notification and record keeping will come into force.
• Requirements of above will come into force in line with type-approval
• From October 2012 it becomes mandatory for a large trailer subject to annual test to be notified to VOSA before it is used on the public road. VOSA will check the vehicle is approved before issuing clearance to use the trailer.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 14
Trailers
Trailers not subject to annual test (under 3500kgs gross weight)ornot used to carry goods.
• From October 2012, it becomes mandatory for the person retailing the trailer to the public to keep records of every trailer sold for a period of 10 years.
• The records must show details of the type approval certificate of conformity or individual vehicle approval (IVA) certificate.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 15
Directives and regulations on motor vehicles, their trailers, systems and components
• Commission Decision of 14 July 2011 correcting Directive 2010/19/EU as regards the amendment of the Annexes to Directive 2007/46/EC
• Commission Regulation (EU) No 678/2011 of 14 July 2011 replacing Annex II and amending Annexes IV, IX and XI to Directive 2007/46/EC of the European Parliament and of the Council (Framework Directive)
• Commission Regulation (EU) No 566/2011 of 8 June 2011 amending Regulation (EC) No 715/2007 of the European Parliament and of the Council and Commission Regulation (EC) No 692/2008 as regards access to vehicle repair and maintenance information
• Commission Regulation (EU) No 582/2011 of 25 May 2011 implementing and amending Regulation (EC) No 595/2009 of the European Parliament and of the Council with respect to emissions from heavy duty vehicles (Euro VI) and amending Annexes I and III to Directive 2007/46/EC of the European Parliament and of the Council
• Commission Regulation (EU) No 183/2011 of 22 February 2011 amending Annexes IV and VI to Directive 2007/46/EC of the European Parliament and of the Council establishing a framework for the approval of motor vehicles and their trailers and of systems, components and separate technical units intended for such vehicles (Framework Directive)
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 16
Items to consider for the future
• General Safety Regulation (GSR) including AEBS
Repeals 50 directives and combines requirements into 1 regulation
Reduces need for testing to EEC requirements as UN ECE Regulations Approvals accepted where available
Start to be phased in from 1st November 2012
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 17
• Masses and Dimensions
• European Small Series Approval (Other categories)
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 18
• Other items discussed at the TCMV of 16 April 2012 included:
Masses and Dimensions
Amendments to Annex IV and XII (2007/46)
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 19
Nationally:
• Revisions have been published to the VOSA IVA Manuals for N2/3 and M2/3
• Brake test requirements due to be published relating to IVA testing of trailers
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 20
The Directive 2007/46/EC became law on the 29 April 2009. The key dates from today are: New types of vehicles
29 October 2012
Existing typesof vehicles(Registrations)
29 April 2012 29 April 2013 29 October 2014
29 October 2012 29 October 2013
2012 2013 2014
Completed vehicles ofCategory N2, N3.
Special purpose vehiclesof category N1, N2, N3, M2, M3,O1, O2, O3, O4
M1 WAV’s, ambulancesand motor homes
Incomplete andcompleted vehiclesof categoriesN2, N3, O1, O2, O3, O4
Completed vehiclesof category N1
Completed vehicles ofcategory , O1, O2, O3, O4
Special purposevehicles of categoryN1, N2, N3, M2, M3,O1, O2, O3, O4
Completed vehiclesof category N2, N3
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 21
Summary
• Automotive legislation is continually moving and changing.
• What has been indicated here has been derived from the
SMMT and Members discussions and consultations at the UK, EC and Globally through the UNECE.
• The legislation is usually written to cover all categories of vehicles. It is one of the roles of the SMMT to filter out only those parts that are applicable to the vehicles that you manufacture. This is especially true of the SENTA guide which I will speak about further later.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the motor industry’ brandline are trademarks of SMMT Ltd
Mike Protheroe, Standards and Legislation Manager VCA
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the motor industry’ brandline are trademarks of SMMT Ltd
Mike Protheroe, Standards and Legislation Manager VCA
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 24
SENTA
SMMT European and National Type Approval
guide
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 25
SENTA - SMMT European and National Type Approval guide A step-by-step web-based programme to guide vehicle manufacturers, bodybuilders and suppliers through the complicated European Community Whole Vehicle Type Approval system. It also allows for national approval schemes for low volume manufacturers.
For a new approval application, SENTA will ease the lengthy process.
SENTA details what a manufacturer must do from the original design idea, through the development and construction stages to completion of the approval process.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 26
SENTA - SMMT European and National Type Approval guide
The guide is split into three parts.
Registered users will be guided through the ECWVTA process from start to finish. This will be based on their specific requirements and supported by:
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 27
SENTA - SMMT European and National Type Approval guide
The guide simplifies the approval process for those dealing with multi-stage builds by requesting specific information. Help information and worked examples are available for each section of the guide.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 28
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 29
First Page
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 30
Section 1 – Start of page
Special purpose vehicle added
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 31
Section 1 – Page continuation
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 32
Section 1 – End of page
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 33
Section 2 – Start of page
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 34
Section 1 flag increased in size for clarity - Application for a Body Builder or Converter
If you are a Body Builder or Converter, please only complete Section 1 and 2 and then go to Section 9. Download and save a copy of the completed Annex I or Annex III Document. Complete the Appendix I - Multi-Stage Build base vehicle summary found at the end of the document. This can be used as part of your Approval application. Dependant on the data listed, you may need to return to Sections 3 to 8 to enter any relevant data there, if necessary.
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 35
103950 Appendix 1 – Multi Stage build vehicle summary
•Stage 1:
•Make or Trade name of manufacturer: e.g SENTA Trucks
•Model or Commercial name: e.g Atago •Type: AT001 •ECWVTA Number: e#*2007/46*####*## of the incomplete/complete vehicle •Stage 2:
•Subjects approved in second stage for the completed vehicle •Lateral Protection – e11*?? •Rear underrun device - e11*?? •Rear registration plate space - e11*?? •Lighting Installation - e11*?? •Spray Suppression – e11*?? •Additional subjects approved:
•Statutory Plates - e11*?? •Masses and dimensions - e11*??
See Section 1 flag note
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 36
Sections 3 to 8
Further vehicle information where applicable
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 37
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 38
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 39
Section 10 list of reference documents
Section 11 General Type Approval Reference documents
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 40
Section 11 General Type Approval Reference documents Item Subject Regulatory act reference N2 EC
WV TAUNECE Regulation
numberSeries of amendments Type Approval applicant
information document required
1Sound levels vehicle 70/157/EEC X 51 02
2 Emissions 70/220/EEC X2a Emissions (Euro 5 and 6) light
duty vehicles/ access to information
715/2007/EC X(9)
3a Fuel tanks/rear protective devices – fuel tanks
70/221/EEC X(5)
34 02
3b Fuel tanks/rear protective devices – vehicle rear underrun
70/221/EEC X(5)
3c Fuel tanks/rear protective devices – STU rear underrun
70/221/EEC X(5)
3d LPG tanks X 67 013e CNG tanks X 110 003f Rear protective device X 58 01
4 Rear registration plate space 70/222/EEC X - -
5 Steering effort 70/311/EEC X 79 016 Door latches and hinges 70/387/EEC X 11 02
7a Audible warning component 70/388/EEC X 28 02
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 41
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 42
INFORMATION DOCUMENT FOR 77/839 TOWING HOOKS
APPENDIX 1 INFORMATION DOCUMENT No ........
Pursuant to Annex I of Council Directive 70/156/EEC relating to EC Type-Approval of a vehicle with respect to the towing-devices
(Directive 77/389/EEC, as last amended by Directive .../...) The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4
format. Photographs, if any, must show sufficient detail. 0. General 0.1. Make (trade name of manufacturer): Alba 0.2. Type and general commercial description(s): BB 0.3. Means of identification of type, if marked on the vehicle (b): VIN 0.3.1. Location of that marking: Cab 0.4. Category of vehicle (c): N3 0.5. Name and address of manufacturer: Alba
Holm Industrial Estate Worthing BN13 2AB
0.8. Address(es) of assembly plant(s): As above 1. General construction characteristics of the vehicle 1.1. Photographs and/or drawings of a representative vehicle: See Annex 1.1
Start of page – note: data automatically entered from input to previous sections. This will happen to any information document saved
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 43
Sections 13 – Type, Variant and Version chart
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 44
Sections 14 – Approval list
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 45
Section 15 – Certificates of conformity
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 46
MODEL B – SIDE 1 ECWVTA COMPLETED VEHICLES
EC CERTIFICATE OF CONFORMITY Side 1 The undersigned ………………………………………………………..(Full name and position) hereby certifies that the vehicle: 0.1Make (Trade name of the manufacturer): …………………………………………………. 0.2: Type: …………………………………………………………………………………………………………. Variant(a):………………………………………………………………………………………………….. Version(a) ……………………………………………………………………………………………………….. 0.2.1 Commercial name: ………………………………………………………………………………………… 0.4 Vehicle category: …………………………………………………………………………………………… 0.5: Name and address of the manufacturer: ……………………………………………………… 0.6 Location and method of attachment of the statutory plates: ……………………… Location of the vehicle identification number: ……………………………………….. 0.9 Name and address of the manufacturer’s representative (if any): ………………………………………………………………………………………………………………………… 0.10 Vehicle identification number: …………………………………………..………………………………….. a) has been completed and altered(1) as follows: ………………………………………and b) conforms in all respects to the type described in approval (…type-approval number including extension number) issued on (…date of issue) and c) can be permanently registered in Member States having right/left (b) hand traffic and using metric/imperial(c) units for the speedometer(d) …………………………………………… ........................................................ (Place)(Date) (Signature) Attachments: Certificate of conformity delivered at each previous stage.
Side 1 of the CoC
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 47
Take a Tour guideline information
The Tour is a snapshot of what is contained in the SENTA Guide which is written to cover all categories of vehicles and the possible Approval Routes. It gives an indication of how the Guide works by showing parts of the Section pages and how they may be used.
The application and compliance data included in the Tour is based on a European Approval for a large Truck built in two stages – ECWVTA N3 MSB
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED PAGE 48
SENTA information and registration
Go to SMMT website, smmt.co.uk, front page and click on the SENTA button in the top right hand corner
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the motor industry’ brandline are trademarks of SMMT Ltd
Q&A session
SOCIETY OF MOTOR MANUFACTURERS AND TRADERS LIMITED SMMT, the ‘S’ symbol and the ‘Driving the motor industry’ brandline are trademarks of SMMT Ltd
Thank you for attending
Society of Motor Manufacturers and Traders Ltd71 Great Peter Street, London, SW1P 2BNwww.smmt.co.uk