SmartviewDoor Camcorder with Color Monitor and

Motion SensorModel No. 184A

Product by: JG Domótica – TEC IT, Tecnologia Inteligência e Domótica, S.A.

Travessa Cabo do Mundo, 681 | 4455-427 Perafita Matosinhos PORTUGAL

Phone. +351 229 999 230 | Fax. +351 229 999 249email: domotica@jgdomotica.com | www.jgdomotica.com

USER’S GUIDE

CautionDo not rotate the camera or recorder without disconnecting the connecting cable first. Damage to the connecting cable will occur!

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future reference.

CONGRATULATIONS

With this Door Camcorder with Motion Sensor, you can capture the video/audio of any visitors even when you are not home. It also allows you to answer your door safely at home before opening. It is a high-quality, battery-

operated security device that uses a passive infrared (PIR) motion sensor to detect guests/intruders at your front or back door, and to activate a video recording and an on-screen image at your home’s side.

This instruction manual explains in simple steps how to install, use and care for your new Door Camcorder in homes, offices or businesses.

PARTS CHECKLIST

Identify all parts before proceeding with installation

1pc. Charger

1pc. Rechargeable Battery

1pc. Clock Battery(installed in Camcorder)

1pc. Color Monitor

1pc. Front Sensor with double-side tape

1pc. Mounting Bracket

2 pcs Supporter

1pc. Screw for Bracket

1pc. Tool

Optional SD/MMC card (if supplied)

FCC Warning Any unauthorized changes or modifications to this equipment would void the users authority to operateThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.Important Safeguards1. Cleaning – Turn off this video unit before cleaning. Do not use strong

or abrasive detergents. Use a dry cloth to clean the camera body when dirty. In case the dirt is hard to remove, use a damp (not wet) cloth for cleaning.

2. Water and Moisture – Do not use any component of this system in an exposed outdoor area except the outer part of front sensor, unless the instructions clearly state that it is safe to. Do not operate this system in the presence of explosive or flammable fumes.

Precautions1. Do not attempt to disassemble the camera. There are no user-serviceable

parts inside.2. Handle the Smartview with care.

Do not abuse the camcorder. Avoid striking, shaking, etc. Improper handing or storage could damage the device. Modifying or tampering with the device or its internal components can cause a malfunction and

THINGS YOU SHOULD KNOW

invalidate the device’s warranty. If your device is not performing as it should, take it to your local dealer for assistance.

3. Clean the lens faceplate with care. Do not clean the lens with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol.

4. Door Mounting – The product should be mounted to a door, only as recommended by the manufacturer

5. Set MODE to PLAY when you are not using your camcorder. It will set the motion detector off and the device to enter the Stand-by status until pressing POWER.

6. Do not touch the LCD screen with a sharp-pointed object.7. If your Smartview is used in a cold place, a residual image may appear

on the LCD screen. This is not a malfunctionPrivacy PerceptionAlways use discretion when installing video and audio surveillance equipment especially when there is perceived privacy, or an expectation of privacy. Inquire regarding federal, state and/or local regulations applicable to the lawful installation of video and/or audio recording or surveillance equipment. Party consent may be required.

FEATURES

Monitor and Sensor Front1. LCD Screen - 1.5” LTPS LCD2. Speaker - play back the audio sound of recorded file at PLAY mode3. SD/MMC Card Insert Slot 4. Battery Cover

5. Microphone6. Motion-activated Sensor – detects motion up to 2 meters (6.5 feet) away

and from a horizontal angle of up to 125 degrees7. Lens

Monitor and Sensor Monitor Back1. Terminal2. Clock Battery Cover

Control Panel1. OK – confirm setting

2. CURSOR –◀▶3. MENU – enter Menu screen4. DISPLAY – press this button to toggle among Full Display On, Texts

Off and Display Off5. MODE switch – go to RECORD, LIVE, or PLAY6. POWER – activates and deactivates the device at selected mode7. RESET – use a pointer or alike to press this button to reset the unitOperation Indicators1. New Message Light Indicator (Green)2. Full Memory Light Indicator (Red)3. Key Light Guide (Blue) – illuminates when user presses any button4. Low Battery Light Indicator (Red)

PREPARATION

Charging CAMERA Battery

Charge Battery fully before use1. Plug in Charger. Red light is on.2. Insert Battery onto the Charger, observing proper +/- polarities as

indicated. Red light flashes.3. When charging is complete, the light changes to Green color.4. Remove Battery.Notes:

* Charging takes about 2 hours.* Amber light will be on in case of abnormal use or bad battery.* Prevent metallic objects from coming into contact with the metal parts of

the terminal of Charger. This may cause a short circuit, damaging the Charger.

* Keep the battery dry.* Battery life gradually decreases after repeated use and recharging. If

operation time becomes very short even after a sufficient charge, discard Battery properly.

* When the battery is not to be used for a long time, charge the battery once fully, and then use it until it fully discharges again. Keep it in a good condition.

Install Battery1. Press and slide down the battery cover. It will be opened up horizontally.2. Install a fully charged Battery into the battery compartment, observing

proper +/- polarities direction as indicated. 3. Press down and slide up to lock the battery cover.

To remove Battery1. Press and slide down the battery cover. It will be opened up horizontally.2. Press Orange BATT RELEASE down to slide the Battery out.3. Press down and slide up to lock the battery cover.

Battery CareCaution:- Charge only with specified charger- Battery can be charged within a temperature range of 10C (50F) and 35C (95F)

- Battery is normally warm after charging or just after use.- Do not use an insufficiently charged or worn-out BatterySafety precautions:- Do not get Battery near, or dispose of, in fire- Do not directly connect (short circuit) the positive (+) and negative (-)

terminals- Never attempt to disassemble or reassemble BatteryTo avoid Battery damage:- Do not drop or jar Battery- Use Battery with specified units only- If Battery is used in extremely high temperatures, a safety device will automatically prevent operationTo prolong Battery life:

- While not in use, remove Battery from the Smartview and Charger, and store in a cool, dark, dry place.

- Keep Battery terminal cleanCharger Caution:- This unit will operate on AC 100-240 V 50/60Hz. - Grounding or Polarization – This video unit may be equipped with either a

polarized 2-wire AC (Alternating Current) line plug (a plug having a blade wider than the other) or 3-wire grounding type plug, a plug having a third (grounding) pin.If the 2-wire polarized plug fails to fit into the power outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.The 3-wire grounding type plug will fit into the grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

- Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Paying particular attention to cords of plugs, convenience receptacles, and the point where they exit from the unit.

- Overloading – Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

- During charging operation, the battery should be kept away from high temperature, high pressure and heat sources. Also it should be kept away from children. Do not charge the battery for over 24 hours.

CLOCK Battery Installation

The clock runs on 1pc CR2032 coin battery (included) in case of lithium battery removal for recharge.1. Remove the cover on the back of the unit. 2. Install 1pc CR2032 battery into the clock battery compartment, observing

proper + / - polarities as indicated. 3. Replace the battery cover.Warning: - Dispose of old battery promptly and properly. Do not burn or bury them.- Replace battery with CR2032 only. Use of another battery may present a risk

of fire or explosion. - Keep away from children. Do not recharge, disassemble or dispose of, in fire.Note: * Keep Battery out of children’s reach. Swallowing it may be harmful. * Battery life is approximately 2 years.SD Card Information

SD/MMC Card Insertion/Removal1. Insert SD/MMC card with the logo facing toward the LCD 2. To remove the SD/MMC card, press on it to release

Record/Playback TimeSmartview is equipped with internal memory for initial recording

This is recommended to use SD/MMC card for enhanced recording lengthResolution 128MB 256MB 512MB 1GFine 15 minutes 30 minutes 60 minutes 120 minutesSP(Standard Play) 30 minutes 60 minutes 120 minutes 240 minutesLP (Long Play)* 40 minutes 80 minutes 160 minutes 320 minutes

* LP playback may contain more picture noise

INSTALLATION

Choosing a Mounting Location

Smartview is designed to mount on a smooth, flat door surface. Select a door where you desire the device to detect an intruder. We recommend mounting it at a height of about 6 feet. At this height, the sensor detects motion up to 2 meters (6.5 feet) away and from a horizontal angle of up to 125 degree.To help you avoid false activation, mount your camera:* where it will not be in direct sunlight* away from heat sources, such as space heaters, radiators, and exposed light

bulbs* out of strong drafts, like those caused by central heating vents

1. Prepare the mounting space (the original door peephole or drill a hole of at least 12mm diameter at desired location)

2. Install the Front Sensor into the front side of your door peephole. Use the double-sided adhesive tape at its back to fix its position on the door.

3. Place the Mounting Bracket at the another side of your door

4. Place the Supporter through the Mounting Bracket & peephole to fit the front camera. Use the Tool to turn the Supporter clockwise until it is secure to the door.

5. Be sure to connect the flexible cable plug to the INPUT Connector by matching the arrow symbols on the plug and the terminal.

6. Remove the insulator of CLOCK Battery from the back side of Monitor7. Hook the Monitor onto the Mounting Bracket. Thread a T-shaped lock to

hole of the unit’s bottom and turn it clockwise.

8. Insert a SD/MMC card (not supplied) into the slot at the right panel of Monitor

9. Press and slide the battery cover in the direction of the arrow. Its metal spring will automatically lift up the door.

10. Insert the Camera Battery into the compartment, as indicated by polarity symbols (+ and -) marked inside. Then close the cover.

OPERATION

For First Use, set MODE to RECORD. Press POWER to turn on the device. The camera will undergo self-calibration within 15 seconds. Smartview has different languages. Select your desired language (see page 71)Set the Time / Date (see page 71).To save battery power, Smartview will go to sleep mode at specific timewhen not in use or no motion is detected.

Operating ModesThe system can be set to operate in one of three modes: RECORD, LIVE or PLAY. The desired operating mode can be selected using the MODE switch on the left side of the front panel of the Monitor.

Motion-activated Video/Audio RECORD

Smartview can record high-resolution video with sound of guests / intruders at your front or back door even when you are not homeBefore you begin---- Check the Battery Indicator - Ensure SD/MMC card is properly installedYour Smartview automatically records for you.1. Set MODE to RECORD.2. A camera icon indicates that the camera is on. The battery icon

appears to indicate the status of battery.3. When motion is detected, the camcorder begins recording in about 3

seconds. It continues recording until motion has ceased for 10 seconds.4. Videos are stored to internal memory. Or, it will be stored to memory card

as standard computer files in sequence if memory card is available. When the memory is full, recording stops and a Full Memory Indicator (Red) is on to tell you to replace it with a new memory card or clear the memory.

5. View recording scene on LCD (Liquid Crystal Display) monitor. Date and time are recorded. Use DISPLAY to switch between LCD ON/TEXTS OFF/LCD OFF.

Motion Sensor may not start when:* Motion is very slow or fast.* Moving object is very small.* Motion occurs only in 1 corner of viewing area.

1:20FINEA

01/01/2005 12:00

Sensor Trigger Capture

Auto Delete Enabled

AWhite Balance AutoSunnyFluorescentTungstenCloudy

Battery Status Full Power Level66% Power Level33% Power LevelEmpty

FINESPLP

Video Quality640x480 @ 15fps320x240 @ 30fps320x240 @ 24fps

SD/MMC card StatusPresent and ValidPresent but Locked

Record StatusCapturing Triggered by PIR sensor

01/01/2005 12:00 AM

Clock Info / Stamp Mode

EV Enabled 1:20 Record Elapsed Time / Remain Time

Set ClockThe clock time is lost in last power off

Extra wide view angle lens let you see whom are at the door before openingBefore you begin---- Check the Battery Indicator - Ensure SD/MMC card is properly installed1. Set MODE to LIVE.2. A user capture icon will appear.3. When turned on, the camera begins to monitor the surrounding in front of

door for motion. It will go to standby mode when motion has ceased for 10 seconds.

Starting LIVE

4. View outside scene on LCD (Liquid Crystal Display) monitor. Use DISPLAY to switch between LCD ON/TEXTS OFF/LCD OFF. Press ◀ to change the Movie Quality (Fine/SP/LP).

5. Press OK to manually start recording. Press OK again to stop recording. Videos are stored to internal memory. Or it will be stored to memory card as standard computer files in sequence if memory card is available. When the memory is full, recording stops and a Full Memory Indicator (Red) is on to tell you to replace it with a new memory card or clear the memory.

PLAY Back Video Files using Monitor

Green light indicator will flash to tell you a new message. You can then monitor the playback picture on the LCD screen.

1. Set MODE to Play. Thumbnail file(s) will appear.2. Uses ◀▶ to select your desired preview.3. Press OK to open it.4. Uses OK to play/pause/replay the video. 5. Use DISPLAY to change between LCD ON/TEXTS OFF/LCD

OFF.6. It will go to standby mode after 1 minute idle.

When a video is playing,- Press ◀ to rewind or ▶ to fast forward the video- Press to zoom in or to zoom out

Zoom is performed digitally, if you set ZOOM to 4x, the picture quality deteriorates

- Hold ◀▶ to pan to desired positionWhen the video is paused/stopped

- Press ◀▶ to skip to previous/next video- Press to increase volume or to decrease it

Notes: - The Smartview saves video files with date and time information- New message light will be off when the video is played- The video capture is stopped when entering the Play Back Mode (Video)

- The file Order depends on DCF Index: CLIP00001 to CLIP09999- The Smartview powers off automatically when battery empty

Video File Auto Delete Enabled

Playback statusVideo stop Video Playing Video Pause

Battery Status Full Power Level66% Power Level33% Power LevelEmpty

21/28 Current File / Total File

SD/MMC card StatusPresent and ValidPresent but Locked

2005/01/0112:00:00

Movie Date and Time

x1 Playback Zoom Ratio

Zoom position White region – WholeGreen region - Zoomed

Set ClockThe clock time is lost in last power off

USING MENU MODE

Before you begin…

2005/01/0312:00:00

2005/01/1012:00:00

2005/01/0912:00:00

2005/01/0612:00:00

2005/01/0112:00:00

2005/01/0112:00:00

21/28

2005/01/0112:00:00

X1

- Check the Battery Indicator - Ensure SD/MMC card is properly installed

1. Press MENU for Menu mode. The Menu screen is entered.2. Press ◀▶ to highlight the desired item3. Press OK to enter the Setting mode of selected item4. After setting, press MENU to exit

Note:- The menu mode is canceled if buttons are not pressed within 1 minute.

RECORD/ LIVE Mode Menu Screen

Select Movie Quality

Select White balance

EV Set Up - Select Exposure Compensation

Choose Auto Off in 5 seconds or 10 seconds

Enable/Disable Auto Delete Function

Enter Setup Mode

Movie

Movie Quality

You can select the Movie quality mode in video recording. The default setting is Standard Play.

Fine (640x480 15fps)

Standard Play (320x240 30fps)

Long Play (320x240 24fps)

1. Set MODE to RECORD or LIVE while the LCD is on.2. Press MENU to enter Menu mode3. Use ◀▶to move to Movie Quality 4. Press OK to enter the setting mode5. Use ◀▶ to select your desired Movie Quality6. Press OK to confirm the selected quality and go back to the last

menu7. Press MENU during setting to cancel the selection and go back to

the last menu

Adjust White Balance

White balance adjustment makes subjects look white and allows more natural color balance for video recording. Normally, white balance is automatically

Movie Quality

Fine

adjusted. You can obtain better results by adjusting the white balance manually to fit your actual living environment.

Auto

Sunlight

Cloudy

Fluorescent

Tungsten

1. Set MODE to RECORD or LIVE while the LCD is on.2. Press MENU to enter Menu mode3. Use ◀▶to move to White Balance 4. Press OK to enter the setting mode5. Use ◀▶ to move to your desired effect (Auto, Sunlight, Cloudy,

Fluorescent or Tungsten)6. Press OK to confirm the selected effect and go back to the last

menu7. Press MENU during setting to cancel the selection and go back to

the last menu

EV Setup

White Balance

Auto

>0 Brighter/ Exposure longer=0 Standard/ Exposure normal<0 Dimmer/ Exposure shorter

1. Set MODE to RECORD or LIVE while the LCD is on.2. Press MENU to enter Menu mode3. Use ◀▶to move to EV Setup4. Press OK to enter the setting mode5. Use ◀ to increase or ▶ to decrease EV value 6. After setting, press OK to save changes and go to screen7. Press MENU during setting to cancel the selection and go back to

the last menu

Choose Auto Off

Adjust EV

0-2.0 2.0

0.0

Auto Off

5 SEC

5 seconds10 seconds

Smartview has a power saving feature that it will automatically go to Stand-by mode whenever it does not detect any motion at RECORD/LIVE mode or leaves idle for a preset period at PLAY mode.

1. Set MODE to RECORD or LIVE while the LCD is ON.2. Press MENU to enter Menu mode3. Use ◀▶to move to Setup4. Press OK to enter the setting mode5. Use ◀▶to select 5 seconds or 10 seconds6. After setting, press OK to save changes and go back to last menu.7. Press MENU during setting to cancel the selection and go back to

the last menu

Enable/Disable Auto DeleteAuto Delete means that the oldest index file is deleted when memory is full

Enable Auto DeleteDisable Auto Delete

1. Set MODE to RECORD or LIVE while the LCD is on without recording.

2. Press MENU to enter Menu mode3. Use ◀▶to move to Auto Delete 4. Press OK to enter the setting mode

Auto Delete

ON

5. Use ◀▶ to move to your desired command (Enable or Disable Auto Delete)

6. Press OK to confirm the selected command and go back to the last menu

7. Press MENU during setting to cancel the selection and go back to the last menu

PLAY Mode Menu Screen

Go to Erase This

Go to Erase All

Go to Volume Level Menu

Enter Setup Mode

Go back to Thumbnail Mode

Erase This

Erase This

1. Set MODE to PLAY and ensure the LCD is on.2. Use ◀▶ to move to your desired file at thumbnail 3. Press MENU to enter Menu mode4. Press OK to enter the setting mode5. Use to select “Cancel” or “OK”. Press OK to confirm the

selected command. 6. If “OK” is selected, the file will be deleted and go to thumbnail

mode; Select “Cancel” to go back to last menu7. Press MENU to cancel the selection and go back to the last menu

Erase All

1. Set MODE to PLAY and ensure the LCD is on.2. Press MENU to enter Menu mode3. Use ◀▶to move to Erase All4. Press OK to enter the setting mode 5. Use to select “Cancel” or “OK”. Press OK to confirm your

selection.

DELETE SINGLEARE YOU SURE ?

Ok

Cancel

DELETE ALLARE YOU SURE ?

Ok

Cancel

6. If “OK” is selected, all files will be deleted and go to last menu; Select “Cancel” to go back to last menu

7. Press MENU to cancel the selection and go back to the last menu

Adjust Sound Volume

1. Set MODE to PLAY and ensure the LCD is on

2. Press MENU to enter Menu mode3. Use ◀▶to move to Volume 4. Press OK to enter the setting mode5. Use ◀▶ to adjust your desired sound level6. Press OK to confirm the selected volume and go back to the last

menu7. Press MENU during setting to cancel the selection and go back to

the last menu

SETUP Screen

Choose LCD Brightness

Volume

7

LCD Brightness

Default Setup

Choose Flicker Option (depending on lighting)60Hz ; 50HzGo to Format MenuGo to Copy All to SD CardGo to Date/Time MenuChoose Language OptionGo to Reset All Settings MenuGo to Firmware Version Info. Menu

Choose LCD Brightness

1. Press MENU to enter Menu mode2. Use ◀▶to move to Setup3. Press OK to enter the setting mode4. Use ◀▶ to move to LCD Brightness. Press OK to enter5. Use ◀ to reduce the brightness value or ▶ to increase it6. After setting, press OK to save changes and go back to last menu7. Press MENU during setting to cancel the selection and go back to

the last menu

Choose Flicker Option

Adjust LCDBrightness

0-2.0 2.0

0.0

This setting is for 50Hz/60Hz lighting. E.g. US: 60Hz

EU: 50HzHK: 50Hz

50Hz Flicker60Hz Flicker

1. Press MENU to enter Menu mode2. Use ◀▶to move to Setup3. Press OK to enter the setting mode4. Use ◀▶ to move to Flicker option. Press OK to enter5. Use ◀▶to select 50Hz or 60Hz depending on your own

country’s lighting condition6. Press OK to proceed the selection and go back to last menu7. Press MENU during setting to cancel the selection and go back to

the last menu

Format Memory Card

Flicker

50Hz Light

1. Press MENU to enter Menu mode2. Use ◀▶to move to Setup 3. Press OK to enter the setting mode4. Use ◀▶ to move to Format. Press OK to enter5. Use to select Cancel or OK. Press OK to confirm the selected

command6. If “OK” is selected, the file will be deleted and go to screen; Select

“Cancel” to go back to last menu7. Press MENU during setting to cancel the selection and go back to the

last menu

Copy All to SD Card

Smartview will automatically detect new SD/MMC card after insertion. Record, Play and other file management tasks will be rerouted from internal memory to SD/MMC card.Copy All function can be used to copy all video files from internal memory at once to SD/MMC card.

Format will eraseAll data

OkCancel

Start Copying Files from internal Memory to SD Card?

Ok

Cancel

1. Press MENU to enter Menu mode2. Use ◀▶to move to Setup 3. Press OK to enter the setting mode4. Use ◀▶ to move to Copy File to SD. Press OK to enter5. Use to select Cancel or OK6. Press OK to start copying. 7. Press MENU during setting to cancel the selection and go back to

the last menuNote:- Those files copied from the internal memory will be stored in a new folder \

DCIM\xxxFLASH\. xxx will take the largest number among the other folders.

- The original files in the internal memory will not be erased.

Set Date / Time

1. Press MENU to enter Menu mode.2. Use ◀▶to move to Setup 3. Press OK to enter the setting mode4. Use ◀▶ to move to Date/Time. Press OK to enter5. Use ◀▶ to move to desired item. The selected item is always

blinking.6. Press to increase the current item’s value or to decrease it.7. After setting, press OK to save changes and go back to last menu.8. During setting, press MENU to cancel selection and go back to last

menu.

Choose Language

1. Press MENU to enter Menu mode

Language

English

2. Use ◀▶to move to Setup 3. Press OK to enter the setting mode4. Use ◀▶ to move to Language. Press OK to enter5. Use ◀▶to select your desired language. The flag will change

according to the selection6. Press OK to proceed the selection and go back to last menu

Default Setup

1. Press MENU to enter Menu mode2. Use ◀▶to move to Setup 3. Press OK to enter the setting mode4. Use ◀▶ to move to Default Setup. Press OK to enter5. Use to select “Cancel” or “OK”. Press OK to confirm the

selected command6. If “OK” is selected, the default setup will be restored and go to

screen at RECORD/LIVE mode, or go to thumbnail at PLAY mode; Select “Cancel” to go back to last menu

7. Press MENU during setting to cancel the selection and go back to the last menu

RESTOREDEFAULT

ARE YOU SURE?

Ok

Cancel

Firmware Version

1. Press MENU to enter Menu mode2. Use ◀▶to move to Setup 3. Press OK to enter the setting mode4. Use ◀▶ to move to Version. Press OK to enter5. Press OK or MENU to go back to last menu

Use “SD / MMC Card”

You can record and play back videos on the SD or MMC card (purchase separately). You can exchange video data with other equipment such as a personal computer etc., using the Memory Stick Reader/Writer or a PC card adaptor (not supplied).Note:* We recommend backing up important data* Smartview supports up to 1 Gz SD/MMC card.* Video data may be damaged in the following cases:- If you remove the SD/MMC, turn the power off, or detach the battery for

replacement when reading or recording data into the SD/MMC. - If you use a SD/MMC near static electricity or magnetic fields* Do not bend, drop or apply strong shock to a SD/MMC* Do not disassemble or modify a SD/MMC.* Do not let the SD/MMC get wet

Version

v601010

* Do not use or keep a SD/MMC in locations that are: - Extremely hot - Under direct sunlight - Very humid or subject to corrosive gases* When you carry or store a SD/MMC, put it in its case.* A SD/MMC formatted by the Windows OS or Macintosh computer does not

have a guaranteed compatibility with this Smartview.

Download Video

To download video images directly from a removable memory card to your PC, a Multimedia or SD/MMC card reader compatible with your computer is required. Your Smartview compresses video data into AVI format.Typical video data file name

Root: folder <DCIM> <100 CODER> CLIP0001~2,3,…. : As displayed on your PC screen

Software Requirements

An XviD codec is required to view recorded movies on your computer’s media viewer. A free XviD codec is available for download from http://www.xvid.org/Downloads.15.0.html and you can grab the current latest stable binary XviD-1.0.3-20122004.exe. Once you install the software, you may need to reboot your computer.Alternatively, DivX codec software is available at the DivX website: www.divx.com.

TROUBLE SHOOTING

If you are having trouble in operating this product, please consult the guide as below:SYMPTOM REMEDIESNo picture in LCD monitor * Set MODE to RECORD or LIVE

* Use fully charged Battery* Firmly connect all needed cables

LCD displays “SENSOR ERROR”

* Check the plug of the flexible cable is properly inserted into the terminal. Make sure camera and monitor are switched ON.

* Make sure camera is not coveredAudio problems Ensure the volume is turned up sufficiently

on the monitorThe power goes off The Battery is dead or nearly dead

Install a charged BatteryThe AUTO RECORD function does not work

* There is no AUTO RECORD in the LIVE, PLAY or menu settings.* Set MODE to RECORD

The battery remaining indicator does not indicate the correct time

* You have used the Battery in an extremely hot or cold environment for a long time.

* The Battery is completely dead, and can not be recharged

Replace with a new BatteryRecording does not function * The SD/MMC card has already been

recorded to its full capacity Erase unnecessary videos and record

again* The SD formatted incorrectly is inserted. Format the SD or use another SD /

MMC card* Check Battery Indicator

NO SD/MMC card * No SD/MMC card or Unreadable SD/MMC card is inserted

* The SD/MMC card is broken or the file format is not proper. Eject the SD/MMC card, check it and insert it again. If the same indicator appear, use another SD/MMC card.

SD/MMC card cannot be inserted

* Insert SD/MMC card, front side facingout

LCD displays * Set the time and date* Replace with a new CR2032 battery for

clock

Specifications

Power Source: Charger 100-240V AC, 50/60HzBattery Lithium Polymer Type DC 3.7V

Power Consumption: 0.5W (operating)Charger 4.2V=0.5CVVideo Recording Camera: 1/5” type CMOS, Approx. 300,000 pixelsLCD: 1.5 inch Color LTPS (557 x 324)File Type: AVIVideo Format: MPEG 4Operating Temperature: 0C ~ 50C (32F ~ 122F)Operating Humidity: 10% ~ 85 %Weight: Smartview 231g (including batteries)

Charger 74 gDimensions: Smartview-Color Monitor 110 x 72 x 24mm

(excluding Mounting Bracket)Smartview - Sensor 60 x 40 x 13mm(excluding Supporter)Charger 28 x 53 x 95mm (excluding adaptor)

Weight and dimensions as shown above are approximation only.Design and specifications are subject to change without prior notice.

Important: For electrical products sold within the European Community. At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.