SmartPIT™ Application Note - Honeywell Video Systems

Rev 2.0 1 © Copyright Honeywell International Inc 2/8/2008

SmartPIT™ Application Note:

Connecting SmartPIT™ interfaced to IP ATM’s to Rapid Eye™

Overview

This document covers -Connecting the SmartPIT to the Rapid Eye -Configuring the SmartPIT to send IP ATM text data to the Rapid Eye. -Configuring the Rapid Eye to accept this text data and store with video

Requirements

Rapid Eye with Version 7 or greater software SmartPIT with Version 2.3 or later SmartPIT accessories “For DVR” connector and 2 M straight through CAT 5 cable, these come included with the SmartPIT


Step 1 Connect SmartPIT Port 1 to Rapid Eye RS232 Port 1 as shown

Notes 1. RELT and REMM only have one serial port you can connect to, port 1 2. REMMDSP V7 or V8 have 10 Serial ports, you cannot use Port 2 it is reserved for other use 3. REMMDSP V7 or V8 Can use the SmartPIT included accessory “For DVR connector and cables for Port 1 connection on the Rapid Eye only. If the SmartPIT is to be connected to Port 2-10 a custom cable must be created 4.RE units can be configured to connect to one SmartPIT in ATM Mode only, this allows for up to 8 Multiplexed ATM data streams to be received from the one SmartPIT (RE is configured for Netpit connection). You could also connect 8 more SmartPIT’s to the other 8 serials Ports setting the Rapid Eye for POS Device.

Port 1 19200, 8, n, 1

RS232 19200, 8, n, 1 Rapid Eye MM DSP V7/V8 Shown Connect to serial port 1 on RELT and REMM

SmartPIT

“For DVR” connector to RS232 Port 1

Straight through CAT 5 cable connect to Port 1

For DVR connector and 2 M Cable included with SmartPIT

Cable included is 2 M, you can use any standard straight through CAT 5 cable to increase the length


Step 2 Program SmartPIT from Web browser

Note –all the following programming can also be done from the front panel of the SmartPIT Connect to SmartPIT using Pc and web browser

Connect a crossover cable between the SmartPIT and the Laptop Set Laptop to Static IP of 192.168.10.152 subnet mask 255.255.255.0 Launch Web browser Enter URL of HTTP://192.168.10.153 Logon use User= smartpit Password= password

Set to ATM Application

Click on Configuration Tab , select Common Configurations Scroll to bottom and click Edit Set Application to ATM Set Operating Mode to Real Time Set Port 1 Settings to 19200, No parity, 1 stop bit, 8 Data bits, RS232 (settings to communicate to Rapid Eye with Click Save when completed


Set Slave Port1 Set ATM IP addresses to decode

Select ATM Configurations Scroll to bottom and click Edit Set Slave Port to PORT1 (this allows you to use the SmartPIT included accessory cable (RJ45-RJ45 ) and connector (RJ45-D9 male labeled FOR DVR) to connect to the Rapid Eye Set Output Format to connected to Rapid Eye Enter IP addresses of each ATM Click Save when completed

Note-leave TCP port set to blank as shown


Step 3 Program Rapid Eye from Remote View to receive live ATM text

Connect Remotely using View to Rapid Eye with V7 or V8 software

Connect to Rapid Eye, Go to Maintain Tab>Serial Devices Click on the + next to Unassigned Devices to expand the choices , see NetPIT, Click and hold on NetPIT and drag NetPIT to Port 1. Leave IP , subnet, Gateway Blank, SmartPIT does not currently support this Set Baud Rate =19200, Data bits 8, Parity none

Note-The NetPIT device accepts multiplexed data from a SmartPIT set in connected to Rapid Eye mode

Add a Virtual POS for each ATM

Click on the + next to Port1-NetPIT to expand and see letters from A to P (4 channel has A-D, 9 Channel A-I, 16 Channel has A-P) Expand New device by clicking on the + , then click and Hold on POS and drag POS to A, Do this for each ATM Data you will interface to , if there will be 3 ATMS drag POS to A, B, C Click on each Virtual POS connection and assign a device name Note-in this example we have used ATM1Camera1, Video and Text are played back and viewed in separate windows , by identifying the camera that points at the ATM it will be easier for the investigator to know which Camera to view with which ATM


Disconnect the View application and reconnect to see the new POS streams for Live viewing with live camera video

Disconnect Rapid Eye View Reconnect Rapid Eye View Click Live and pull down File , Select Add stream Select a Virtual POS that you wish to see live incoming text data from

View Live Incoming text beside the live camera

View Live incoming text beside the live camera


Step 4 Program Rapid Eye to record Text Event Transactions

Boosting Recording Is Not Required Rapid Eye is a record always device unless a schedule is enabled in Maintain>Schedule check Overlay a schedule Rapid Eye can be set to boost the recording rate on incoming text data if required. Boosting recording is typically used to increase the number of Images per second captured when a client performs an ATM transaction. This way more pictures are captured of the client performing the transaction Boosting Recording on text in Procedure Summary of the Procedure you will do Step 1 –Select a Text trigger string or character from the input ATM text transactions that when detected will start boosted recording Step 2. Set an event rule for Each ATMPOS in Serial Devices Step 3. Set the Boosted Rate for the camera in Video Step 4. Configure a Camera schedule if required Step 5 Verify Boosting occurs Step 1 –Select the Trigger String In the below example the Rapid Eye has been set to boost recording on text in on POS connection titled ATMCamera1 When Boosted recording occurs a series of yellow boxes appear above the camera as shown The text from the ATM is shown. We will set the Rapid Eye to trigger whenever any text transaction comes in. We need to identify a common character or string of characters in all transactions to do this. In this example the transaction text always starts with ha Date and time stamp .Ex- 12/05/01 The data values may change but the / character does not so we will tell the Rapid Eye to start boosting recording whenever a /character is detected . We will also tell the Rapid Eye to continue the boosted recording for 5 seconds after the detection of the / character


Step 2 –Set the Event rule that will boost recording In View go to Maintain>Serial Devices Click on the A-POS that you created to see the following Enter an Event name, we choose Boost Camera 1 Enter the Event rule that will trigger the Boosted Recording, we have chosen the / character as described in the previous step Click add when entered, if you change this you will click the update button Click apply at the bottom when completed


Step 3 –Set the boosted recording rate Go to Maintenance>Video Click on Camera 1 Click on Boosted Set the Desired Boosted Resolution, Image per second Rate and Video Quality Click apply at the bottom of the Page


Step 4 Enable the Recording Rule and Set the schedule if required Go to Maintain>Schedules Click on the Rule that exists that matches what you started, in this example it is rule 1 When rule is selected the ATMCamera1 box is no longer greyed out Click on the ATMCamera1 box to set a check next to it to enable it Click on the Boost Camera 1 box to set a check next to it to enable it Click on the boost recording box under Camera 1 to insert a check box to enable this Click on the Radio button next to Lasts and also enter 5 for the seconds to boost the recording Click apply at the bottom of the screen IF you require a specific schedule set this in the Sunday to Exception schedule table In this example no special schedule is set so the rule will be active always


To see a summary of what the rule will do click on describe rule


Step 5 Verify Boosting occurs Close or minimize the Maintenance session Click on live>File>add stream Select the POS stream and the camera you expect to boost recording , display both side by side When not boosted Red boxes appear at the top of the camera 1 screen

When the Trigger text is detected and Boosted recording starts and is continuing Yellow boxes Will appear at the top of the camera 1 screen


Step 5 Search Rapid Eye and playback Text Event Transactions and video

Method 1 Click on Events>Data Recording Click on the ATMCamera1 Set a from time and to time that will include a transaction Click start Events within the time duration will be listed at the bottom of the page Click on one to select then click Video to see it played back


Method 2 Click on Data Click on the Data to search for already present or enter Edit search data Click Start A data event list will appear Click on one to select then click on Video to play it


Additional Information

See the Honeywell Video Systems website at http://www.honeywellvideo.com/ For SmartPIT http://www.honeywellvideo.com/products/solutions/pr/125775.html For RapidEye http://www.honeywellvideo.com/products/recorders/index.html


Honeywell Video Systems Louisville, KY 40299, USA www.honeywellvideo.com

‡„ +1.800.796.2288

Honeywell Security Australia Pty Ltd. Unit 5, Riverside Centre, 24-28 River Road West

Parramatta, NSW 2150, Australia www.ademco.com.au ‡„ +61.2.8837.9300

Honeywell Security Asia Pacific

Flat A, 16/F, CDW Building, 388 Castle Peak Tsuen Wan, N.T., Hong Kong

www.security.honeywell.com/hk ‡„ +852.2405.2323

Honeywell Security France Parc Gutenberg, 8, Voie La Cardon

91120, Palaiseau, France www.honeywell-security.fr

‡„ +33.01.64.53.80.40

Honeywell Security Italia SpA Via della Resistenza 53/59, 20090 Buccinasco

Milan, Italy www.security.honeywell.com/it

‡„ +39.02.457.1791

Honeywell Security España Calle Vivero, 5, 28040

Madrid, Spain www.security.honeywell.com/es

‡„ +34.91.102.5900

Honeywell Security Nederland Netwerk 121

1446 WV Purmerend, Netherlands www.SecurityHouse.nl

‡„ +31.299.410.200

Honeywell Video Systems UK Ltd. Aston Fields Road, Whitehouse Ind Est

Runcorn, Cheshire, WA7 3DL, UK www.honeywellvideo.com

‡„ +44.1928.754.030

Honeywell Security South Africa Unit 6 Galaxy Park, 17 Galaxy Avenue, Linbro Park

P.O. Box 59904, 2100 Kengray, Johannesburg, South Africa

www.honeywell.co.za ‡„ +27.11.574.2500

Honeywell Security Germany

Großenbaumer Weg 8 40472 Düsseldorf, Germany www.honeywell-security.de

‡„ +49.211.41.50.90

Honeywell Security Poland Chmielewskiego 22a, 70-028

Szczecin, Polska www.ultrak.pl

‡„ +48.91.485.40.60

Honeywell Security Czech Republic Havránkova 33, Brno

Dolní Heršpice, 619 00, Czech Republic www.olympo.cz

‡„ +420.543.558.111

Honeywell Security Slovakia Republic Vajnorská 142, 83104 Bratislava

Slovakia www.olympo.sk

‡„ +421.2.444.54.660

Honeywell Video Systems

www.honeywellvideo.com +1.800.796.CCTV (North America only)

© 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes. Specifications subject to change without notice. Imperial conversions are approximate

Documents

SmartPIT™ Application Note - Honeywell Video Systems