SmartAX MT882 ADSL Router Quick Start

Thank you for purchasing SmartAX MT882 ADSL Router (hereinafter referred to as the MT882). With the MT882, you can enjoy high-speed Internet services while making a phone call.

1 Safety Precautions Pay attention to t ling and using the MT882. he following when instal

the

the telephone line, to avoid

During lightning weather, disconnectdevice from the power supply. Unplug all cables connected withthe device, such as the power cable and

lightning strike.

Do not dispose the device to direct sunlight.

Place the device at a well-ventilated place.

a g

Do not use an old or a 　damaged power cable.

Keep the power plug clean and dry. Using dirty or wet power plumay lead to electric shock or other perils.

operation of the device, keep the device dry.

During storage, transportation and

1

Do no let a child operate the device without guidance. Do not let a child play with the device or any accessory. Swallowing the accessories may lead to peril.

In any of the following cases, stop using the device, disconnect it from the power supply and unplug the power plug immediately: there is smoke emitted from the device, or there is some abnormal noise or smell. Contact the specified maintenance center for repair.

Keep at least 10 cm between the device and the closest object for heat dissipation. Keep the device far away from any heat source or bare fire, such as a candle or an electric heater.

Do not place any object on the top of the device. Otherwise, the device may be too hot during operation. It can even be deformed or damaged by the heavy load.

Before cleaning the device, stop using it and disconnect it from the power supply. Use a piece of soft cloth to clean the device.

Never attempt to dismantle the device by yourself. In case of any fault, contact the appointed maintenance center for repair.

Note: When the MT882 is used for a long time, temperature of the shell will rise slightly. This is normal and does not affect the performance of the device.

2

2 Connecting the MT882 Step 1 of Connect the ADSL interface of the MT882 with the MODEM interface

the splitter by using the telephone line.

MODEM

ADSL EthernetReset

Power 12VAC 0.8AUSB

Step 2 Connect the splitter. Connect the LINE interface of the splitter with the telephone jack in the wall by using another the telephone interface b

telephone line. Connect the PHONE interface of the splitter with y using the other telephone line.

PHONE

LINE

3

Step 3 Connect the computer. Connect the Ethernet interface of the MT882 with that of the computer by using the network cable.

ADSL EthernetReset

Power 12VAC 0.8AUSB

Connect the power interface (which is labeled 12V Step 4 AC 0.8A) of the MT882 with the power socket by using the power adapter.

ADSL EthernetReset

Power 12VAC 0.8AUSB

4

Step 5 Press down the Power button of the MT882.

ADSL EthernetReset

Power 12VAC 0.8AUSB

3 Front Panel

Note: Figure of the front panel is only for your reference.

Indicator Status Description Steady green light The MT882 is powered on. Power

Off The MT882 is powered off.

5

Indicator Status Description Blinking green light

The MT882 is being activated.

Steady green light The MT882 is activated.

Blinking orange light

The embedded PPP dial-up software is being used for dialing.

Steady orange light

The embedded PPP dial-up software succeeds in dialing.

ADSL LINK

Off The telephone line is not connected or the next activation is being prepared.

Blinking green light

There is traffic over the ADSL interface. ADSL ACT

Off There is no traffic over the ADSL interface.

On The Ethernet interface is normally connected.

Blinking green light

There is traffic over the Ethernet interface and the data is transmitted at 10 Mbit/s.

Blinking orange light

There is traffic over Ethernet interface and the data is transmitted at 100 Mbit/s.

LAN

Off The Ethernet interface is not connected with the network cable.

Steady green light The USB interface is normally connected. Blinking green light

There is traffic over the Ethernet interface.

USB

Off The USB interface is not connected.

Note: If the MT882 fails to be activated, it tries again after an interval. In such an interval (about 1 minute), the ADSL LINK indicator is off.

6

4 Configuring the MT882 You can access the Internet by using the following two methods:

Using the Embedded PPP Dial-Up Software of the MT882 to Get Online Using the PPP Dial-Up Software of the Computer to Get Online

configuration. If the configuration is wrNote: Please use the parameters provided by your service provider for

ong, you cannot access the Internet.

Using the Embedded PPP Dial-Up Software of the MT882 toStep 1 Set

enter the Web

4. indow. You can access the Web page when this authentication is passed.

Step 2 Configure the MT882 and enable the embedded dial-up function. 1. Select Basic > WAN Settings in the navigation tree. 2. Find the permanent virtual channel (PVC) to be configured. Click the

Get Online up the configuration environment.

1. Connect the MT882 with your computer by using a straight-through cable.

2. Configure the IP address of your computer to be in the same network segment as the IP address of the LAN port of the MT882. The default IP address of the LAN port: 192.168.1.1 The subnet mask: 255.255.255.0

3. Start the Internet Explorer (IE) on your computer and address of the MT882 in the address bar. The default Web address of the MT882: http://192.168.1.1 Enter the user name and the password in the displayed login w

icon of the PVC to display the following configuration page.

7

Note: The actual configuration page may vary with the version of the MT882. The previous figure is only for your reference.

3. Set Mode to PPPoE and configure the other parameters, such as

VPI/VCI, the user name, and the password. 4. Click Submit. 5. Select Basic > DHCP in the navigation tree to display the DHCP

configuration page. 6. Select Tools > Save & Reboot from the navigation tree. 7. Select Save and click Submit to save your configuration. 8. Select Reboot and click Submit to restart the MT882.

Step 3 Configure your computer.

Configure your computer to obtain network settings, such as the IP address, the gateway, and DNS.

8

Note: If the embedded dial-up function of the MT882 is enabled, power off the MT882 when you do not want to access the Internet. Otherwise, the service provider may still calculate the fee for Internet services even if you have powered off your computer.

Using the PPP Dial-Up Software of the Computer to Get Online Step 1 Configure the MT882 to work in the pure bridge mode. Refer to steps for enabling the embedded dial-up function to configure the pure bridge mode. The only difference is to select the Pure Bridge mode not the PPPoE mode. Step 2 Configure the network card (also called network adapter) for your computer. If the PPP dial-up software is installed in your computer, and then you can get online. The Windows XP (Professional) operating system has an embedded PPPoE dial-up software. To set up a dial-up connection in the Windows XP system, do as follows:

1. Select Start > All Programs > Accessories > Communications > Network Connections.

2. Click Create a new connection in the displayed page. 3. Click Next in the New Connection Wizard dialog box. 4. Select Connect to the Internet and click Next. 5. Select Set up my connection manually and click Next. 6. Select Connect using a broadband connection that requires a user

name and password and click Next. 7. Enter the name of the dial-up connection (you can enter the name as you

like). Then click Next. 8. Select Anyone's use or My use only and click Next. 9. Enter the user name and password. Then click Next. 10. Click Finish.

9

5 FAQs

1. Why does the ADSL connection break so often?

Many possible factors may cause this problem, such as faults in your service isturbance. You can do as

ld industry standard architecture (ISA) network adapter with a new connect (PCI) network adapter and install the

provider's access server, line disconnection, and line dfollows:

Ensure that the ADSL line is connected properly. Keep the MT882 away from appliances with strong electric fields or magnetic

fields, such as a microwave oven and a refrigerator. Ensure that no telephone or fax machine is connected directly with the ADSL line.Replace the o10/100M peripheral component interlatest driver.

Contact your service provider for help.

2. Will the call service and the ADSL access service influence each other?

The MT882 separates the voice and data signals through the FDM technique. Though transmitted on the same telephone line, voice and data traffic do not interfere with

each other and the two services will not be influenced.

3. I cannot get online for I changed the parameters of the MT882, what can I do?

the MT882. t button, and then release it.

Restore the default factory settings of the MT882 as follows: (1) Find the Reset button on the rear panel of(2) Use a needle-like object to press the Rese

4. The Power indicator is off, what can I do?

MT882. pply correctly.

Check as follows: Whether the power adapter is suitable for the Whether the MT882 is connected to the power su Whether the Power button is pressed down.

5. The ADSL LINK indicator is off, what can I do?

Check as follows:

10

tion

lly by testing with a telephone line. in the device.

Whether the telephone line is correctly connected with the splitter. Whether there is junction box in the telephone line. If yes, ensure that the junc

box does not contain components such as the capacitance and the diode. Whether the telephone line works norma Whether the telephone line connector is correctly plugged

6. The LAN indicator is off, what can I do?

Che82 and the computer is the

rrectly. f your computer is on.

or ! mark under Network ninstall and then re-install them. If the problem etwork card.

ck as follows: Whether the provided network cable between the MT8

correct type. Whether the network cables are connected co

Whether the network adapter indicator oWhether the network card works normally. Select Hardware > Device Manager; Check whether there are devices that have the ?adapters. If such devices exist, uremains, change the slot for the n

7. Why cannot I access the Internet?

Take the commonly-used access mode (a dial-up software is installed on your

l cannot access the Internet after the dial-up operation, check whether d. The Proxy server must be

eb sites, in case some Website fail. Try to stop the dial-up connection and to re-establish the dial-up connection 5

minutes later.

computer) as an example: Ensure that all the previous problems are addressed. Ensure that the dial-up software is correctly installed and set on your computer.

Ensure that you have entered the correct user name and password. If you stilthe Proxy server on your IE is correctly configuredisabled. Try different W

11

6 Specifications Technical

General Specifications ADSL Annex A standards

ITU-T G.992.1 (G.dmt) ITU-T G.994.1 (G.hs) ANSI T1.413 Issue # 2

ADSL2 standards

ITU G.992.3 (G.dmt.bis) Annex A

Standards

+ ADSL2standard

ITU G.992.5 Annex A

G.dmt The maximum downstream rate is 8 Mbit/s The maximum upstream rate is 896 kbit/s

Data transmission rate

T1.413 The maximum downstream rate is 8 Mbit/s The maximum upstream rate is 896 kbit/s

Physical and Environmental Specifications Power consumption < 5 W

Power adapter output 12 V AC 0.8 A

Temperature of the working environment 0℃–40℃ (32℉–104 )℉

Humidity of the working environment 5%–95% (non-condensing)

Dimensions (L × W × H) 136 mm × 113 mm × 34 mm

Weight < 210 g

This product has been designed to comply with the requirements on environmental

rotection. For the proper storage, use and disposal of this product, national laws and pregulations must be observed.

12

o part of this document may be reproduced or transmitted in any form or by any awei Technologies Co., Ltd.

Copyright © Huawei Technologies Co., Ltd. 2007. All rights reserved. Nmeans without prior written consent of Hu

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., td. L

All other trademarks and trade names mentioned in this document are the property of ctive holders.

t to ensure accuraall statements, information, and recommendations in this docuthe warranty of any kind, express or implied.

Issue: 05 (2007-08-27) No.: 102013

their respe

Notice The information in this document is subject to change without notice. Every effort has been made in the preparation of this documen cy of the contents, but

ment do not constitute

13