3
SLIP TEST 1 1. How many grams are there in 1 kilogram? (1) …………………………………………………………………………………………………………….. 2. Write down the following in km, 2000m, 200m, (1) ………………………………………………………………………………………………………………… 3. How many significant figures are there in 505, 1500 (1) ……………………………………………………………………………………………………………….. 4. What is the SI unit of time, length,mass? (3) ………………………………………………………………………………………………………………... 5. The 500 pages of a book have a mass of 2.5 kg, what is the mass in g (1) …………………………………………………………………………………………………………………….. 6. What is the difference between accuracy and precission ? (2) …………………………………………………………………………………………………………………………………………………. …………………………………………………………………………………………………………………………………………………………. …………………………………………………………………………………………………………………………………………………………. ……………………………………………………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………………………………………………… 7. Write down 3 examples for scalar and vector quantity (3) ……………………………………………………………………………………………………………………………………………………………. ……………………………………………………………………………………………………………………………………………………………….. …………………………………………………………………………………………………………………………………………………………… 8. The width of a wooden block is measured using vernier calipers. (1)

Slip test 1

Embed Size (px)

Citation preview

Page 1: Slip test 1

SLIP TEST 1

1. How many grams are there in 1 kilogram? (1)

……………………………………………………………………………………………………………..

2. Write down the following in km, 2000m, 200m, (1)

…………………………………………………………………………………………………………………

3. How many significant figures are there in 505, 1500 (1)

………………………………………………………………………………………………………………..

4. What is the SI unit of time, length,mass? (3)

………………………………………………………………………………………………………………...

5. The 500 pages of a book have a mass of 2.5 kg, what is the mass in g (1)

……………………………………………………………………………………………………………………..

6. What is the difference between accuracy and precission ? (2)

………………………………………………………………………………………………………………………………………………….

………………………………………………………………………………………………………………………………………………………….

………………………………………………………………………………………………………………………………………………………….

………………………………………………………………………………………………………………………………………………………………

………………………………………………………………………………………………………………………………………………………………

7. Write down 3 examples for scalar and vector quantity (3)

…………………………………………………………………………………………………………………………………………………………….

………………………………………………………………………………………………………………………………………………………………..

……………………………………………………………………………………………………………………………………………………………

8. The width of a wooden block is measured using vernier calipers.(1)

Page 2: Slip test 1

What is the width of the block?

A 3.5 mm B 5.3 mm C 8.0 mm D 8.5 mm

9. What is the reading on this micrometer?(1)

A 5.43 mm B 6.63 mm C 7.30 mm D 8.13 mm

10. The diagram shows part of a micrometer screw gauge.(1)

What is the reading shown?

A 5.31mm B 5.79mm C 5.81mm D 6.31mm