SL1000 Training (System Installation)

8/10/2019 SL1000 Training (System Installation)

1/45

Date: 2011-Apr-26 Version: 1.0

Product Technical TrainingProduct Technical Training(System Installation)(System Installation)


2/45

Page 2 NEC Confidential

Part 1 : Hardware InstallationPart 1 : Hardware Installation


3/45


Important Notice Important Notice

To avoid shock or damage, do not plug in or turn the system on before completing theinstallation process. Avoid working with the KSU during electrical storms.Use only commercial AC Power to prevent shock or fire.Use the power cord supplied for the KSU.Do NOT bundle AC Power cords together, the cords may over heat.Make sure the KSU has proper Earth Ground.The system should be Wall-Mounting only.A dedicated 110/240VAC circuit located within 2 meters of the KSU is required. Aseparate AC outlet is necessary for each KSU.

Meeting established environmental standards maximizes the life of the system.Be sure the site is NOT :

In direct sunlight or in hot, cold or humid places.In dusty areas or in areas where sulfuric gases are produced.

In places where shocks or vibrations are frequent or strong.In places where water or other fluids comes in contact with the equipment.In areas near high-frequency machines or electric welders.Near computers, telexes, microwaves, air conditioners, etc.Near radio antennas (including short-wave)


4/45


Wall Mounting (1)Wall Mounting (1)

The Main KSU ( ) and Expansion KSUs ( ) must be mounted ontothe wall. Before installing, secure appropriate spacing as below.

! !


5/45


Wall Mounting (2)Wall Mounting (2)

" ! " !


6/45


ExpansionExpansion KSUs KSUs

Connect between Main KSU andExpansion KSU by using cable which isattached to the Expansion KSU.

EXIFB- C1 card is necessary for KSUsInter-Connection.

##$ %$ %

% " % & ' % " % & ' ##$ %$ % $ & " ( " % )*+ &$ & " ( " % )*+ &

, ", "


7/45


Grounding Grounding

The ETH lug is located near Power supply unit on each KSU. Connect ETH lug to the verified Earth Ground point by using 14AWG (2.0mm) wire.

- " - "

- " ( & " % % . !- " ( & " % % . !- " / " ! ' ! ( %- " / " ! ' ! ( %& ' $& ' $ ## 0 " %0 " %


8/45


Power Failure Transfer Power Failure Transfer

SLT is connected to the Extension Port No. 8/16/24/32. Change the switch position of J6 from KT to PF . (Default : KT)

$ % " , ( & 1+$ % " , ( & 1+

Trunk Port Ext. Port

No. 1 No. 8

No. 5 No. 16

No. 9 No. 24No. 13 No. 32

Max. Quantity

4 per KSU *

(*Note: Total PFT circuit is 12, 4 th chassis no PFT)


9/45


CablingCabling Trunk (1)Trunk (1)

Each I/F card provides RJ11 connectors. One RJ11 connector is provided each Trunk port.

0* )*+ % & $ $ &0* )*+ % & $ $ &% ( %% ( %

0* )*+ % & 0* )*+ % & ' / %! " . %' / %! " . %

% & % % % & % & % % % & ' '

" & )*+ " " & )*+ " + 2 ( & " 1+ 2 ( & " 1

Max. Quantity3 per system *

1 per system

1 per system

(*Note: 1 per KSU, 4 th chassis not supported)


10/45


CablingCabling Extension (2)Extension (2)

Each I/F card provides RJ11 connectors. One RJ11 connector is provided each Extension port.

0* )*+ % & $ $ &0* )*+ % & $ $ &% ( %% ( %

0* )*+ % & 0* )*+ % & ' / %! " . %' / %! " . %

% & % % % & % & % % % & ' '

" & )*+ " " & )*+ "

Max. Quantity

128 per system96 per system

12 per system

Type

AnalogDigital

DSS Console

6 per systemDoorphone


11/45


! +31 4 0 $ .! +31 4 0 $ . 5 56 !6 !7 7 1+ " .1+ " . 5 56 !6 !7 7

CablingCabling Extension (2)Extension (2)


12/45


Cable Length Cable Length

Max 1125 m (0.5mm)

Max 300 m (0.5mm)

Max 100 m (Ethernet Cable)

KTSDSS

SLT

Doorphone

ISDNTerminal

Max 150 m (0.5mm)

PCPrinter

LAN

1632M

1632M / 1632ME408E / 008E

1632M

2BRIDBMax 500 m (0.5mm)

Max 100 / 300 m (0.5mm)

Max 100 m (Ethernet Cable)LAN


13/45


4 4 08 08 E / 008E / 000E / PRIU Installation (1)E / 008E / 000E / PRIU Installation (1)

408E / 008E / 000E / PRIU cards are installed in the 1632M / 1632ME KSU.

408E / 008E / 000E / PRIU*

8) 9 6: !8) 9 6: !


14/45




408E / 008E / 000E / PRIU*

8) 9 6: !8) 9 6: !


15/45




408E / 008E / 000E / PRIU*

8) 9 6: !8) 9 6: !


16/45




8) 9 6: !8) 9 6: !


17/45


Optional Items Installation (1)Optional Items Installation (1)

EXIFB-C1 card can be installed at 1632M KSU .

3;


18/45



MEMDB card can be installed at 1632M KSU, CPU card .

3 0=3 0= ##$$


19/45



PZ-VM21 card can be installed at 1632M KSU, CPU card .

6>6> ## ? ?


20/45



CF card can be installed at 1632M KSU, PZ-VM21 card .

$< $ " $


21/45



VOIPDB-C1 card can be installed at 1632M KSU, CPU card .

?* 60= ?* 60= ##$$


22/45


Part 2 : System Start Up & ProgrammingPart 2 : System Start Up & Programming


23/45


Start Up (1)Start Up (1)

There are 2 types of Data :

' '

$ ( 0$ ( 0

Pre-stored into the Memory located onto 1632M KSU. Can be upgraded from the CF (Compact Flash) Card which is inserted to

CF Slot at PZ-VM21.

Automatically be saved to the memory on 1632M KSU. Backed up by LithiumBattery.

Can be saved to the CF Card which is inserted to CF Slot at PZ-VM21. Can be saved to your PC by PC PRO software.


24/45



Main software and Default data will be loaded. (System Initialization)

1. Confirm CF Slot is empty at PZ-VM21.2. Open Sub-Cover of Main KSU, press and

hold on to S1 switch as indicated:3. AC Power Switch ON.4. System Power Switch ON.5. Hold on to S1 switch for about 3-4

seconds and release it.6. Now the Status LED (D5) starts flashing

RED.7. Wait about 1-2 min.8. Cold Start operation done.

There are 2 types of startup mode :

$*10 $*10


25/45



Main software and Customer data will be loaded. (System Reset)

1. AC Power Switch ON.

2. System Power Switch ON.3. Wait about 1-2 min.4. Hot Start operation done.

@*+ @*+


26/45


Accessing Programming (1)Accessing Programming (1)

Programming can be accessed 3 separate ways :

From Display type Desktop TerminalPossible to set the data by following the manual.

Web ProgrammingDoesnt need special application because the application is built into SL1000system. Just standard Web browser is necessary, and on-line programming isavailable.

PC Programming

The special application which is provided by NEC-i should be installed on thePC that will be used for PC PRO. Doesnt need real SL1000 system, off-lineprogramming is also available, and the customer data can be saved on the PC.

3 default passwords/Levels are built into the System. (IN / SA / SB)

The IN (Installer) Level has full access to all programs.

The SA / SB (System Admin) Levels have limited access.


27/45


Accessing Programming (2)Accessing Programming (2)

1 user

0

0

PC PRO

1 user

4 users

4 users

Total

0

4 users

2 users

Web PRO

0

0

2 users

DesktopTerminal

No.3

No.2

No.1

CombinationExample

Following number of users can enter the Programming Mode at the same time.

From Desktop Terminal : Up to 2 usersFrom Web PRO : Up to 4 usersFrom PCPRO : Up to 1 user

Auto Log-Out is available in case nobody operates during pre-programmedperiod on the Programming from Desktop Terminal and Web PRO. This periodis programmable by PRG20-01-12 (Default : 900 sec)

In case of PCPRO, only 1user can enter the PRGMode at the same time.


28/45


Enter / Exit Programming Mode Enter / Exit Programming Mode

1. Press SPK Key.

2. Dial #, *, #, *.3. Dial Password.4. Press HOLD Key.

1. Return to PRG No. entering screen

by pressing MUTE Key.2. Press SPK Key.3. Return to normal mode. (Time&Date)

Procedure on Display Key Telephone

Normal Mode PRG No. Entering screen

Key Description0-9, * and # Enter data into a Program

HOLD Complete the programming (ENTER Key)

MUTE Exit one step at a time (ESC Key)

FLASH Switch the cursor between 1st and 2nd Display


29/45


Program Number Program Number

Chapter No.

Program (PRG) Number means as below.

10

Particular No. Item No.

10 : System Configuration Setup 11 : System Numbering

:

01 : Time and Date 02 : Location Setup

:

01 : Year 02 : Month

:

( ' 6 ( " .( ' 6 ( " . 5 5 ( )( ) 7 7 % % 5 5 7 7

( % (( % (

01 01- -


30/45


Concept of Slot Number Concept of Slot Number

The system may ask you the Slot No. in the specified Program Number.

Slot 1 (408M)

Slot 2 (408E/008E/000E/PRIU)

Main KSU

Slot 5 (408ME)

EXP KSU (1)

Slot 9 (408ME)

EXP KSU (2)

3;


31/45


Software Upgrade (1)Software Upgrade (1)

1. Power off the system.

2. Store new Main Software data in yourCompact Flash Card (CF) by using PC.

3. Insert the CF Card into Memory Card

Slot on PZ-VM21.

4. Open Sub-Cover of Main KSU, press andhold on to S1 switch as indicated:

5. AC Power Switch ON.

New Main Software will be provided by NEC Infrontia.

6 % "6 % "

6>6> ## ? " & ( ! " ' ! ( " . ? " & ( ! " ' ! ( " .


32/45


Software Upgrade (2)Software Upgrade (2)

6. System Power Switch ON.

7. Hold on to S1 switch for about 3-4 seconds andrelease it.

! "

9. Now the Status LED (D2-5) starts flashing RED.

10. System Power Switch OFF.

11. Remove CF card from PZ-VM21.

12. System Power Switch ON.

To check the Main Software Version :(On-Hook Condition)Press Enter Key and Dial 821.

Main Ver.: 07.00

0-60-B9-C1-F9-7C


33/45


Main Software Version Confirmation Main Software Version Confirmation

1. On-hook condition.

2. Press Enter Key (Navigation Key).

3. Dial 821 to show the Main Software version &Hardware Key Code.

4. Press Right Key (Navigation Key) to show the MainSoftware version & MAC address.

5. Off-Hook and return to Time & Date mode.

Follow the steps stated below to check your SL1000 main software version byusing the Multi-Line Telephone.

6 % "6 % "


34/45


Data Save and Shutdown Data Save and Shutdown

The Customer Data can be saved to CF Card.

1. Insert the CF Card to CF Slot at PZ-VM21.

2. Enter to the Programming Mode.3. PRG 90-03. (Dial 90, 03, 01)4. Dial 1 and press HOLD Key.5. Wait about 1 min. (depends on the system size)6. Display will be changed to next PRG No. after completing the saving.

7. Exit from Programming Mode.8. Remove the CF Card.

The system shall be OFF by pressing AC Power switch located at Power Supply.

$ ( 0 . $< $ "$ ( 0 . $< $ "

! ( 0! ( 0

## 0* )*+0* )*+ '' &! " % % $ '' &! " % % $ ## % ' A $ & 6 *)4*


35/45


WEB / PC PRO (1)WEB / PC PRO (1)

1632M

PZ-VM21

LAN

PSTN(Analog)

: (: (

Modem

1 %1 %

Ethernet Cross Cable

Ethernet Straight Cable

HUB

Analog Trunk

ISDNModem

PSTN(ISDN)

BRI / PRI

ISDN DDI

IP VPNIP Network

HUBHUB


36/45


PC Specification for WEB / PC PRO PC Specification for WEB / PC PRO

6$ % ' % : % (( " "6$ % ' % : % (( " "

Allow to use Cookie which is

saved on PC : Enable Allow to use Cookie for eachsession : Enable

Active Scripting : Enable

MS Internet Explorer 6.0 (or higher)Mozilla Firefox 1.0.3 (or higher)

Browser

8000TCP Port

35MB for PCPro (minimum)Hard Disk Space

LAN, or ModemCommunication Port

128MB of RAM, 256MB (recommended)Memory

Pentium III 598MHz (minimum)

Pentium 4 2.5GHz (recommended)

CPU

Windows XP or Microsoft VistaWindows 7 (32 and 64bit)

O/S

Required SpecificationItem

' 0 % $ % . 3 $ & ' 0 % $ % . 3 $ &

1. Directly connect between ETHERNET port on SL1000 CPU card and PCby Ethernet Cross Cable.

2. TCP/IP is set to 192.168.0.1 on PC.3. Open Browser and type http://192.168.0.10.

(This IP Address is default setting for CPU card. HOT Start is necessary if it is changed.)

This is example to access Web PRO via Ethernet Cable. (Direct Connection)


37/45


WEB PRO (1)WEB PRO (1)

1 %1 % @ ( %@ ( %

User Name : techPassword : (IN Password)

Click Login

Log Out

## 1 * ( & "1 * ( & "## % & % &

C ( ' 1 1 C ( ' 1 1 ' % & ! " ' % & ! " 5 51 *1 * 7 7

Menu


38/45



Up to 2 Log-In modes are provided for End Users. (UA Mode / UB Mode).It is user friendly GUI design, and the user can easily key-in the data and selectthe desired data by using pull-down menu at each column without experiences on

system programming.

D D

$% &! '! " % ( ( ) &"% " %&(

UA Mode

UB Mode

D D

6:* 6:*


39/45



" E " E " E

Allows user administrators to setup system features by using Web Browser.

11 ## *&+ , %&( !&

- %%. (' / (

- Time and Date Setup- Music On Hold- Automatic Night Mode SwitchingSetting- DISA User ID Setup- Mailbox Setup- Selectable Display Messages- Incoming Ring Group Extension- Speed Dialing Number and Name- Night Mode Switching (Another Group)- DSS Key Assignment

- Doorphone Ringing Assignment- Dial-In Name- Telephone Setting- Trunk Setting


40/45



- Extension Name- Night Mode Switching- Call Forward- Trunk Incoming Ring Tone- Internal Incoming Ring Tone

- LCD Language Selection- Toll Restriction Override Password

(not Walking Toll Restriction)- User Programming Password- Programmable Function Keys Assignment- Virtual Extension Ring Assignment

- One-Touch Key Assignment

Allows the extension users to setup own extensions settings by using Web Browser.

) &"% " ! &(

= " E = " E = " E

11 ##

+0 ) &"% "1% %%. ('

( )


41/45


PC PRO (1)PC PRO (1)

11

PC PRO software must be installed to your PC.

Following Login dialog appears.Enter the User Name and Password.


Menu Screen



42/45




$ % 6$ 6:* ! ($ % 6$ 6:* ! (

Click

IP Address of ETHERNET Port onCD-CP00 Blade

(Default IP Address: 192.168.0.10)

Click



43/45



+ & + &

Menu Tab

Menu Screen

Standard(Major settings)

Wizard(Feature Base)

System Data(PRG No. Base)



44/45



= " $ '= " $ '

Right Click to show the Blade Menu

: " 6:- ) "4 < " : " 6:- ) "4 < " = " $ ' ' ( = " $ ' ' (


45/45


Documents

SL1000 Training (System Installation)