SK 영문 07.07.13~현재 -유효 - Cole-Parmer · 1. Check the front and rear sides of the unit under packed condition. 2. Carefully unpack the package. 3. Check with care any damage

Page 1

OPERATING MANUAL [SHAKER]

Model: SK-300 / SK-600/ SK-71 Manual No: 00HAA0001149 (Version :5.0)

This operating manual describes the important subjects to maintain the product¡s

functions and to use it safely. Especially, be sure to read <Safety Precaution> carefully

before you use this equipment. Please keep this operating manual close to the equipment to

use it after reading through it once. Please place it where the new user can find it

easily for the safety use when you hand over or lend the equipment to others.

.

Page 2

Table of Contents

Chapter. 1: Introduction Caution about the operating instruction----------------- 5

Warning mark of the product----------------------------- 5

Caution for safe operation and reorganization

of the product ------------------------------- 6

Disclaimer --------------------------------------------- 6

Introduction of shaking system ------------------------- 7

Chapter. 2: Transportation Confirmation

and Installation Unpacking and Transportation Confirmation-------------- 10

Shaker Components ------------------------------------- 11

Installation ------------------------------------------ 12

Chapter. 3: Safety Alert and Caution Safety Alert ------------------------------------------ 15

Safety Caution ---------------------------------------- 16

Chapter. 4: Part names and Controller Instructions Part names and functions------------------------------- 18

Operating and functional element ---------------------- 19

How to operate

Input shaking speed ------------------------------- 20

Timer programming --------------------------------- 20

Time programming -------------------------------- 20

Examples of Timer programming ------------------- 23

Shaker movement indication ------------------------ 24

Chapter. 5: Switching Orbital/ Reciprocation Motion

and Stroke width adjustment How to switching orbital/ reciprocation motion

Switching motion orbital to reciprocal in SK-300 ------ 26

Switching motion orbital to reciprocal in SK-600 ------ 27

Switching motion orbital to reciprocal in SK-71 ------- 28

How to change the stroke width adjustment

How to change shaking stroke on SK-300, 600 ----------- 29

How to change shaking stroke on SK-71 ----------------- 32

Page 3

Chapter. 6: Maintenance and Troubleshooting Maintenance ------------------------------------------- 36

Safekeeping and Cleaning ------------------------------ 37

Troubleshooting---------------------------------------- 38

Chapter. 7: Specification Specification ----------------------------------------- 41

Chapter. 8: Warranty and Service Warranty standard-------------------------------------- 43

Page 4

Chapter. 1

Introduction

Thank you for purchasing the Lab Companion Shaker.

Lab Companion shaker is for cultivating animal or plant cells as

well as microorganism cultivation. The system is integrated with

shaking table and motor. Excellent shaking for smooth oxygen

supply, ph uniformity, culture fluid in growth environment.

Lab Companion shakers are realized perfectly the control and

shaking circumstance related to the operator¡s experimental

condition. Before using the shaker, please comprehend the manual

in detail.

Chapter. 1 - Introduction is composed as follows.

Caution about the operating instruction

Warning mark of the product

Caution for safe operation and reorganization of the product

Disclaimer

Introduction of shaking system

Page 5

Caution about the operating instruction

1. Always keep this instruction near to the instrument.

2. Copying and distributing part or the whole of this the operating instruction with

no permission are prohibited with the law.

3. The operating instruction promised perfection but please ask an agent or us if you

have any question about insufficient points, error and omission on the operating

instruction.

Warning mark of the product

1. This operating instruction uses the warning Signal Word for safe operation to

prevent the users from accidents or damage beforehand.

2. Defined by the Symbol Mark about the safety caution.

¡Warning¡ means that the user may have serious

damage and even die by improper handling on this

unit.

¡ Caut i on¡ means t hat t he user may have mi nor

damage and uni t may have physi cal damage by

i mpr oper handl i ng on t hi s uni t .

Protective Ground Terminal

It marks the terminal must be connected Ground

prior to operating the product.

I t marks addi t i onal i nformat i on on the operat i on and

features of t he product

3. Be fully aware of the warning contents during operation.

4. Please exchange original label to the new warning label when it is unreadable from

warning out.

☞ Please request the new label to an agent or us.

Page 6

Caution for safe operation and reorganization of the product 1. In order to protect the product and system, please use the product in accordance

with the instructions.

2. We shall not be responsible for any incidental or abnormal operation for breach of

any express or implied warranty on this product or any part thereof.

3. It forbids reorganization of Inside of the product or adds.

4. Please contact the agent or us in case of the component and the consumable parts

of the product will be replaced.

5. Do not give a strong shock to the product. It becomes the cause of product damage

and wrong operations.

Disclaimer

1. In no event will Jeio Tech industries be liable for any incidental or

consequential damages for breach of any implied warranty relating to the product.

2. Any special indirect or consequential property or commercial damage of any nature

whatsoever. Some cases do not allow the exclusion of incidental or consequential

damages, so the above limitation may apply to you.

Page 7

Introduction of shaking system Shaker is for cultivating animal or plant cells as well as microorganism cultivation. The

system is integrated with shaking table and motor. Excellent shaking for smooth oxygen supply,

ph uniformity, culture fluid in growth environment.

Shaking System Feature

Brushless DC Motor

Enables the user to control the motor speed in a circuit diagram and the motor rev up by a

controller.

Fly Wheel System

Excellent in energy efficiency by fixed low level.

Quiet and low vibration with Anti-Weight Fly Wheel System.

Bracket

Double formation between Motor and Bracket.

Possible to adjust the fixing location of the belt.

Photo Sensor

Photo Sensor can perceive a reciprocating motion. As soon as motion is perceived by the

sensor, the shaking system stops at the position exactly. Photo sensor can control the

stop function at exact position.

Shaking Control Function Stop function at the exact position.

When stopping the shaking system, the function operates on stopping at the exact position.

This function contains the Brake Function for the automatic system in Shaker.

Forward/ Backward Function

Shaking controller contains Auto Reserve Function which can operate Forward/Backward and

Time set Function which can be programmable to set Forward/Backward Function.

Velocity compensation Function

While rotating the motor, the velocity compensation function checks the set RPM and then

memorize. This function can control changeable velocity as set value.

Page 8

Auto Control Function

Operate stable RPM from 10RPM to 300RPM. The r ot at i on RPM can be pr ogrammabl e r el at ed

t o t he exper i ment al condi t i on.

Rapid Acceleration and Retardation

Actualize rapid Acceleration and Retardation using of Velocity Compensation Function and

Brake Function.

At the same time, minimize Over Shoot and Under Shoot.

Page 9

Chapter. 2

Transportation Confirmation

and Installation

Before you install Shaker, inspect it for damage that may have

occurred in transportation. Confirm any damage for compensating

following the Compensation regulations and transportation of Lab

Companion. Be sure to check the electric conditions for electric

safe. All persons expected to carry out operation, installation and

maintenance of the unit, read and understand the safety information

and operating instructions.

Chapter . 2 - Transpor tat i on Conf i rmat i on & I nstal l at i on are composed

as f ol l ows.

Unpacking and Transportation Confirmation

Shaker Components

Installation

Select a proper place

Level off the machine

Power connection

Page 10

Unpacking and Transportation Confirmation

Protection from any damage occurring in transit, Lab Companion administers excellent

packing and radical transportation.

Any damage or loss during transit, all responsibility is filled with the delivery carrier.

After receiving the unit, carefully unpack and inspect it for damage.

If the unit is damaged or loss during transit, Make sure as follows to be protected from

the ¡Lab Companion Regulations¡

Confirmation a damaged unit 1. Check the front and rear sides of the unit under packed condition.

2. Carefully unpack the package.

3. Check with care any damage during the transportation of the unit

4. Check the parts (i.e. accessories- Page 11) of the unit.

Compensation regulation of damaged unit If the unit is damaged, contact the delivery service company immediately.

1. Keep the condition as it delivered and wait for the confirmation by the carrier.

2. Within 15 days, submit an application be made in writing to the delivery service

company.

Do not discard the carton or packing material

for the unit until you have checked all of the

damaged parts.

Compensation regulation of transport

1. Any damage that is occurred during the transport is responsible to the delivery

service company.

2. Except for all damage from the transport, we Jeio Tech will service or return.

3. If Jeio Tech or our authorized dealers do not deliver the unit, Jeio Tech disclaims

all the responsibility for the damage.

Page 11

Shaker Components After unpacking, Please check listed shaker component description as follows.

If you didn¡t receive one or more component as follow, Contact the Jeio Tech Service

center or the distributor where you purchased.

Operating manual After unpacki ng, check the operat i ng

manual . I f you di dn¡ t recei ve the

operat i ng manual , Contact the di st r i butor or the Jei o Tech servi ce center .

Fuse

Dur i ng bei ng i n use, i f you contact

t he servi ce center or t he di st r i butor ,

you wi l l recei ve the servi ce.

Power Cord Check the power cord matches the supply

voltage.

Spacer-Option

SK-300: M5*43L(4EA)

SK-600: M5*43L(4EA)

Page 12

Installation

The machine should be installed on a safe and proper environment following to the below.

Check Points Select a proper place

Level off the machine

Power connection

Select a proper place

1. Operating condition: Class 100 ~ Class 10,000 as Clean environment degree for Bio

Clean room is optimal condition for shakers.

Room condition of temperature and humidity should be normal as 18 ℃ ~ 25℃, below

80%RH.

2. Environmental condition: Do not expose the machine to direct ray of light.

3. Setting place: The floor should be on flat and leveled ground.

4. Space: The machine should be kept at least 1.5m from any illuminators and 20 cm from

walls.

The machine should be operated at the optimum

condition for cleanness, electricity and

preparation against fire.

Level off the machine All of the bottom sides should be leveled.

Page 13

Power connection Check the ID Plate on the back side of the machine to find the electric conditions.

Do not connect the power before checking

how to do correct operation.

1. Check i f t he pl ug condi t i on and el ect r i c wi r es ar e normal .

2. Check the connection of ground wire.

Check the power plug to find if the

electric conditions are correct. The

voltage fluctuation should be within 10%

Page 14

Chapter. 3

Safety Alert and Caution

¡Alert¡ shows t hat user s can

be dead or ser i ousl y wounded by

wr ong oper at i on.

¡Notice¡ shows t hat user s can

be wounded or machi nes broken by

wr ong oper at i on.

¡ Si gnal Wor d¡ i s used i n t he operat i on manual f or saf e and

pr oper oper at i on and keeps user s f r om bei ng damaged by

acci dent s.

Each ¡ Symbol Mar k¡ i s i dent i f i ed f ol l owi ng t o t he degr ee of

i mpor t ance and danger .

Pay at t ent i on t o t he ¡ Al er t ¡ and ¡ Not i ce¡ i n t he manual t o

avoi d f rom any acci dent s.

Page 15

Safety Alert

¡Alert¡ shows that users can be dead or

seriously wounded by wrong operation.

Check the voltage, phase and capacity on the ID plate before installation. Sources

of electricity should be separately wired.

The sources of electricity should be grounded.

The sources of electricity without ground connection can cause serious damage to

users or the machine. Don¡t earth the machine to gas pipes or water pipes.

Do not install the machine near to places where inflammable gas can be leaked.

Do not use the machine near to places where explosion can be happened due to

organic evaporating gases.

Explosive materials: Acid, Esther, Nitro compound

Inflammable materials: salt peroxides, inorganic peroxide, salt acids

Put off the power plug if some sounds and smell, smokes are happened.

Do not expose the machine in direct sunlight.

Do not use the machine at places where moisture is high and flooding can be

happened.

Do not disassemble or fix, change the machine.

Check if there is big vibration while the machine is operated.

Check ¡Troubleshooting¡ on the manual.

At least 2 persons should move the machine when it is necessary.

The weight of the machine is about 24 ~ 50kgs. Please use other devices to move

the machine.

Page 16

Safety Caution

¡Notice¡ shows that users can be wounded

or machines broken by wrong operation.

Do not put heavy things on the power line. Do not put the machine on the line.

It causes fire and electric shock.

Connect the plug correctly and do not touch it with wet hands.

It can cause fire if the connection is not fit.

It can cause fire and damage to users.

Do not make the machine wet while cleaning. Do not put liquid on the machine.

If the machine is wet, off the power and contact where you purchase the machine to

check it.

Do not shock the machine or vibrate it.

It can cause damage to the machine.

Do not clean the machine with solvent abstergent. Use smooth cloths.

Cleaning with solvent can cause fire and deformity.

Do not touch the shaking table while the machine is operated

Stop the machine by using Start/Stop button and do necessary works.

Do not put anything near to the turning radius of the machine while operation.

Turning radius of the machine is from 20mm to70mm.

Do not put the sample in a flask installed shaking table.

It can cause damage to the machine.

Be sure to pull out the flask from the shaking table to put the sample in and then,

install the flasks.

Do not put the sample over the max scale shown on the flask.

It can prevent from overflowing the sample When the machine operates in max rpm.

Page 17

Chapter. 4

Part names and Controller instructions

Users should be familiar with how to control the controller before operation. Please do operate the machine after checking chapter 4 for 2~3 times. Please do trial test of the machine without loading any sample flask on it. Please do contact us if you have request while using the controller. Contents of chapter 4

Parts name and function Operating and Functional element How to operate

- Input shaking speed - Timer programming - SHAKER Movement indication

Page 18

Part names and functions

1. Shaking Table: Orbital and reciprocating motion is performed

2. Receptacle with Fuse: Electric Socket with fuse.

3. Foot: Supporter of the body. The supporter can be adjustable its height.

4. Body: Fly Wheel system is equipped inside the body.

5. Control Panel: Shaking controller, power switch and LED signal lamp are set.

5

4

2

1

3

Page 19

Operating and functional element

1. MODE Indicates each operating function.

2. SV/TIME

Set time an remaing time display. 3. PV/RPM

Speed of rotation displays. 4. Shaker LED

TIMER LED : In case of Timer mode, it is ON once total run time is set. F/WARD LED : It is ON, once time for clockwise rotation is set. B/WARD LED : It is ON, once time for clockwise rotation is set. PAUSE LED : It is ON, once time for pause is set.

5. Adjust keys

UP key: To increase value. ( value moves faster on pressing and holding.) DOWN key : To decrease value. ( value moves faster on pressing and holding.) Enter key : To store value or finish set.

6. SHAKE/SET To set shaking speed and timer.

7. START/STOP

To start and stop unit. 8. Power Switch

1 2 3

4 5 6 7 8

Page 20

How to operate

Input shaking speed 1. Press SHAKER/SET key.

2. Press UP/DOWN key. Input RPM.

3. Press Enter Button. Finish to set value.

4. Press START/STOP key. Shaking starts in clockwise rotation.

※ Recall function of RPM value

- Previous RPM value starts if new RPM is set again.

Timer programming 1. Time Programming

- Programming time can not be done during shaking. So, stop shaking by pressing START/STOP key and start programming.

1) Input total run time

1. Press SHAKER/SET key Twice. This section is for setting total run time. ¡run.H¡ shown on MODE display.

2. Press UP/DOWN Button to set Time and then press

ENTER key to store the value. (Max Input Time: 1~999 hours) After setting the value, TIMER LED is on.

3. Press SHAKER/SET key.

This section is for setting minute and seconds. ¡run.S¡ shown on MODE display

4. Press UP/Down key to set minute and seconds and then

press Enter key to store the value.

(Max Input Time: 10seconds~ 59 minutes 59 seconds)

Page 21

2) Programming Forward time

1. Press SHAKER/SET key. This section is for setting Time Forward. ¡For.S¡ shown on MODE display. 2. Press UP/DOWN key to set Time and then press ENTER key to store the value.

(Max Input Time: 10 seconds~ 59 minutes 59 seconds) After setting the value, F/WARD LED is ON.

3. If not use F/Ward function, do not press Enter key. 3) Programming Backward time

1. Press SHAKER/SET key. This section is for setting Time Backward. ¡bAc.S¡ shown on MODE display.

2. Press UP/DOWN key to set Time and then press ENTER key to store the value. (Max Input Time: 10 seconds~ 59 minutes 59 seconds)

After setting the value, B/WARD LED is ON.

3. If not use B/Ward function, do not press Enter key.

Time for

Clockwise

rotation

Time for

Anticlockwise

rotation

Page 22

4) Programming Pause time 1. Press SHAKER/SET key.

This section is for setting Pause. ¡PAu.S¡ shown on MODE display.

2. Press UP/DOWN key to set Time and then press ENTER

key to store the value. (Max Input Time: 10 seconds~ 59 minutes 59 seconds)

3. If not use Pause function, do not press Enter Button.

5) Condition of Timer Programming

1.¡Total program time¡ is the best standing. After operating total program time¡, the shaker stops.

2. If not input time of F/Ward or B/Ward , the shaker operates fixed RPM before pressing START/STOP Button.

3. If input PAUSE Time, the shaker operates fixed RPM forward before pressing START/STOP Button.

RUN TIME: Total program time. F/WARD: Clockwise B/WARD: Anticlockwise PAUSE: Stop shaking temporarily.

Run Time value should be bigger than total time of F/WARD, B/WARD and PAUSE Time.

Press Enter button to omit the function among F/WARD, B/WARD and PAUSE Time. The value is not stored and then press SHAKE/SET button to go on next section.

Time for

Pause

Condition to

set timer

Page 23

6) Cancelation of Timer Programming 1. Press SHAKER/SET Button to go on the desired section. A related section LED is on.

2. Press ENTER Button. After finishing cancelaton, A related section is off.

2. Examples of Timer programming

1) Total program time + F/WARD + PAUSE 1.¡Shaking control using ofTimer fuction¡1)Input Total program Time.

2.¡Shaking control using ofTimer fuction¡2)Input F/WARD Time. 3.¡Shaking control using ofTimer fuction¡

3) Do not Input B/WARD Time, Press SHAKER/SET Button to go on the next section.

4. ¡Shaking control using ofTimer fuction¡4) Input PAUSE Time. 5. Press START/STOP button to operate after checking TIMER,

F/WARD,PAUSE LED is on

2) Example of Timer Input After finishing the timer of Total program time, the shaker stops rotating. Input Total program time and then select B/WARD,F/WARD,PAUSE to input. * Example of Timer 1. Total program Time + F/WARD 2. Total program Time + B/WARD 3. Total program Time + F/WARD + PAUSE 4. Total program Time + B/WARD + PAUSE 5. Total program Time + F/WARD + PAUSE + B/WARD 3) Input rotating time When Total program time doesn¡t input, the shaker keeps operating by rotating time. Select B/WARD,F/WARD,PAUSE to input. * Example of Timer 1. F/WARD 2. B/WARD 3. F/WARD + PAUSE 4. B/WARD + PAUSE 5. F/WARD + PAUSE + B/WARD

Cancel of

specific

timer

Example of

Programming

shaking mode

Example of

Time input

Page 24

SHAKER Movement indication

This Function is for displaying the presnt shaking table.

When maintaing rpm, the display starts a circular movement.

Forward (accelation)

Forward (deceleration)

Backward (accelation)

Backward (deceleration)

Shaking indication

on LED

Page 25

Chapter. 5

Switching Orbital/Reciprocation Motion and Stroke width adjustment.

Shaking motion can be changed from Orbital to Reciprocating or from Reciprocating to Orbital. Furthermore, Stroke length can be adjusted so that your valued experiment is highly efficient. Please, choose proper motion and stroke length for optimal experiment. Chapter 5. How to switch orbital motion to reciprocating motion

SK-300 SK-600 SK-71

How to change the stroke width adjustment SK-300 & SK-600 SK-71

Page 26

How to switch orbital motion to reciprocating motion - Motion selectable, Factory default: Orbital motion

Switching motion orbital to reciprocal in SK-300

Shaking Table - Remove the universal platform and miscellaneous accessories from the Shaking table.

- Keep the working area enough for assembling. - Follow the next instructions.

-

[Inside of Shaking System]

1. Remove the Shaking table from the unit.

Remove M5x10, wrench bolt (4mm, wrench handle) from the Shaking table.

2. Remove M5*23L, Spacer (13mm, spanner) from the upper vibrating frame.

The upper vibrating frame is designated to move as the orbital motion.

3. Install M5*43L, Spacer (13mm, spanner) into the lower vibrating frame.

The lower vibrating frame is designated to move as the reciprocating motion.

4. Reinstall the Shaking table onto the unit in the reverse order.

Make sure that a space (M5*43L) complied with our standard dimension before using. It may cause serious damage to the unit if it¡s too much forced to install above parts.

Shaking table

Spacers for reciprocating motion

Spacers for reciprocating motion

Spacers for orbital motion

Upper vibrating frame

Lower vibrating frame

Page 27




-

[Inside of Shaking System]


Remove M5x10, wrench bolt (4mm, wrench handle) from the Shaking table.

2. Remove M5*28L, Spacer (13mm, spanner) from the upper vibrating frame.

The upper vibrating frame is designated to move as the orbital motion.

3. Install M5*43L, Spacer (13mm, spanner) into the lower vibrating frame.



Make sure that a space (M5*43L) complied with our standard dimension before using. It may cause serious damage to the unit if it¡s too much forced to install above parts.

Lower Spacer Install position

Upper Vibrating Frame (Orbital Motion)

Lower Vibrating Frame (Reciprocating Motion)

Lower Space Install position

Shaking Table

Page 28





- Remove M5x8, flat head bolt(+, screw driver)

- from the Shaking table.

2. Remove M5*35L, Spacer (13mm, spanner)

from the upper vibrating frame.

Figure ? [Inside of Vibrating Frame]

3. Install M5*35L, Spacer (13mm, spanner) to the lower vibrating frame.



It may cause serious damage to the unit if it¡s too much forced to install above parts.

Shaking Table

Lower Spacer Install Position

Upper Vibrating Frame

Lower Spacer Install Position

Lower Vibrating Frame

Page 29

How to change the stroke width adjustment How to change shaking stroke on SK-300, 600

1) Loosen M5x10, wrench bolt (4mm, wrench handle)and then separate the shaking table(A).

(See Figure #1)

2) Loosen M4x8, flat head bolt(+, screw driver) in the position of both side of body

cover(B).(See Figure #1)

3) Loosen 2 ea M5x15, wrench bolt(4mm, wrench handle) in the position of Bracket(C)& 2

ea 5mm knot(8mm, spanner)in the position of Bracket(D).(See Figure #2).

4) Loosen 4 ea M5X12, wrench bolt(4mm, wrench handle) in the position of Frame

Fixture(E).(See Figure #2)

B. Body Cover

A. Shaking Table

[ Figure #1 ] [ Figure #2 ]

[ Figure #4 ]

Upper/Bottom Vibrating Frame set

[ Figure #3 ]

Driving Wheel

C. Bracket

D. Bracket E. Frame Fixture

F. Position Sensor

STROKE 40mm

STROKE 30mm

STROKE 20mm

Page 30

5) Take care and ensure that there will be separated parts Upper/Bottom Vibrating

Frame. There will be Drying wheel and RPM sensor in the Body.

6) Disassemble RPM Sensor (F), (+, screw driver) and then Fix it to the modified

Stroke. (See Figure #4).

[Figure #6]

7) After turning Rotary Spin Fin (H) in the position of Driving Wheel, There is 4 ea

M5 X 10mm,

Wrench bolt under the Hole. (See Figure #5)

8) Remove 4ea M5X10mm, wrench bolt (4mm, wrench handle). Rotary Spin Set (H) will be

separated.

9) Locate the position of the stroke fixture hole of the Driving Wheel Set.

(See Figure #6)

10) Fit and Fix out the rotary spin set into the stroke fixture hole after setting it

to the required position. The correct stroke length can either be 20, 30, 40mm.

11) Reinstall the shaking table into the unit in the reverse order.

[Figure #5]

G. Belt

H. Rotary Spin I. Wrench bolt

Driving Wheel Set

Stroke Fixture hole

Rotary Spin Set

Page 31

* Installing position for stroke fixture.

Stroke 20mm Stroke 30mm

Stroke 40mm

How to fix 1. Select the Stroke range to be desired

as in the picture, take the right position of the driving wheel onto the system unit.

2. Fit and fix out the 4ea M5x10mm, wrench bolt (4mm, wrench bolt handle) into the rotary spin set of the fixture hole according to each stroke. * Fixture hole consists of 4 holes each stroke in the position of square points.

Page 32

How to change shaking stroke on SK-71

1. Loosen M5x8, flat head bolt(+, screw driver) from the shaking table(A).(See Figure #1)

2. Loosen M4x8, flat head bolt(+, screw driver) in the position of both side and back

side of body cover(B) to separate from the body.(See Figure #1)

3. Loosen 2 ea M5x15, wrench bolt(4mm, wrench handle) in the position of Bracket(C)& 2

ea 5mm knot(8mm, spanner)in the position of Bracket(D).(See Figure #2).

4. Loosen 4 ea M5x8, wrench bolt(4mm, wrench handle) in the position of Frame

Fixture(E).(See Figure #2)

B. Body cover

A. Shaking Table

[Figure #1]

C. Bracket

D. Bracket

E. Frame Fixture

[Figure #2]

Upper/Bottom Vibrating Frame

F. RPM Sensor

Shaking System Unit

Body

[ Figure #3 ] [ Figure #4 ]

STROKE 50mm

STROKE 60mm

STROKE 70mm

STROKE 40mm

STROKE 30mm

Page 33

5. Now then, make sure that there will be the vibrating frame set and the system unit

in the unit. (See Figure #3).

6. You can see 4 ea M5x10mm, wrench bolt under the Hole after spinning out the rotary spin

set(G).(See Figure #4).

7. After turning Rotary Spin Fin (H) in the position of Driving Wheel, There is 4 ea

M5X10mm, wrench bolt under the Hole. (See Figure #5)

8. Remove 4ea M5X10mm, wrench bolt (4mm, wrench handle). Rotary Sin Set (H) will be

separated. (See Figure #6)

9. Fit and fix out the rotary spin set into the stroke fixture hole after setting it

to the position. To be desired for the right stroke which can be possible into 20,

30 or 40mm.

10. Reinstall the shaking table into the unit in the reverse order.

Driving Wheel Set

Stroke Fixture Hole

H. Rotary Spin Set I. Wrench bolt

[Figure #5] [Figure #6]

Page 34

※ Installing position for stroke fixture.

Stroke from a front view

How to fix

1. Sel ect t he St roke range to be desi red as

i n t he pi cture, t ake the r i ght posi t i on of

t he dr i vi ng wheel ont o the system uni t .

2. Fi t and f i x out t he 4ea M5x10mm, wrench

bol t (4mm, wrench bol t handl e) i nto the

rotary spi n set of t he f i xt ure hol e

accordi ng to each st roke.

* Fi xture hol e consi sts of 4 hol es each st roke i n

the posi t i on of square poi nts.



Stroke 70mm

Page 35

Chapter. 6

Maintenance and Troubleshooting The shaker would be maintained on the best condition by check

the functions and state periodically. In addition to prevent of

pollution of culture fluid or samples that could be occurred

during tests.

The chapter 6 illustrates trouble that could be occurred

operating the unit. Please request the service refer to this

operating manual when trouble occurs.

Maintenance

Weekly/ Monthly/ Quarterly/ Annually

Safekeeping and Cleaning

Safekeeping way/ Exterior cleaning/ Interior cleaning

Troubleshooting

Main power

Mechanical shaking system

Page 36

Maintenance

Check the all accessories and volts on the platform

are tight up.

Check the platform and shaking table are tight up.

Do not cl ean the sur face of uni t wi t h

sul fur i c aci d, hydrochl or i c aci d or

organi c sol vent .

I t may det er i orat e t he abi l i t y of t he

product .

Check the main power and plug.

(Refer to the chapter 2 ¡installation¡)

Check that the setting values and are correctly

inputted to press the buttons.

Make a routine check weekly/ monthly.

Check the shaking and timer functions of the

controller.

Check the incubated shaking funtion.

Make a routine check monthly/ annually.

Follow the safekeeping way and

maintenance standard to care for the

unit so that, keep the best condition

and quality of the unit.

Page 37

Safekeeping and Cleaning

Safekeeping way If the shaker is not used for a while, maintain as follow.

1. Please take off the plug to turn off the power switch.

2. Maintain the unit with packing to prevent dust

inserting inside.

Exterior cleaning 1. Clean up the body using a soft cloth with neutral

detergent

2. Wipe with a dry cloth the LED screen.

Interior cleaning 1. Please turn off the power switch

2. Take off the platform connecting with the shaking table

and then remove interior dust or obstacle.

3. Clean up the body using a soft and wet cloth with

neutral detergent

4. Wipe with a dry cloth.

Cl eani ng t he i nter i or of uni t may

cause damage on syst em or any other

par t s. Be careful l y cl ean up t he

i nter i or of uni t .

Safekeeping way

Exterior cleaning

Interior cleaning

Page 38

Troubleshooting If any trouble occurs by operting the unit, please follow the bellow directions.

If the existing soultions will not solve problems or does not exist, please request the

service immediately.

Trouble related with main power Trouble Causes Solution

The unit does not

turn on

Connecting incorrect electric power

Power failure or circuit

breaker shuts down

Main plug inserts incorrectly

Socket/ plug/ main power

line might be cut

Fuse short

1. Check the correct power and

voltage of the ID plate sticking

on the back side of unit. 2. Find out the causes of power failure

and recovery.

3. Insert the main power plug correctly. 4. If the socket/ plug/ main power line are

cut, request the service.

5. Exchange the fuses installing on the

back side of unit. (Refer to Page 18)

6. If the problems do not solve, request

the service.

Fuses ar e of t en

bur nt out

The fuses do not fit the

main power

The main power might be cut or aparted

Humidity might inflow into

the main power inserting

part

1. Check the voltage and ampere of fuses.

Model Capacity

SK-300 250V/3.15A

SK-600 250V/3. 15A

SK-71 250V/3.15A

2. If the main power line is cut or

aparted, exchange it.

3. If there is humidity on the inserting part, clear it and reconnect.


the service.

Circuit breaker of

building(room) is

often shorted

Too many plugs connect at the same time

1. Check the voltage supplied circuit breaker.

2. Check that several similar units are

inserted together, if so you should not

use overly. 3. If the problems do not solve, request

the service.

Page 39

Trouble related with main power Trouble Causes Solution

Main power turns on

but switch lights

off

Blackout

Main plug does not insert

correctly Fuses are cut

Faulty connection of main

switch

Inferior main switch

1. Check there might be blackout. 2. Main plug connects with socket correctly. 3. If fuses are cut, exchange new one. 4. If the problems do not solve, request

the service.

Mai n swi t ch l i ght s

on but di spl ay does

not show

Inner harness trouble

Poor transformer Cotroller and display

trouble

1. Request the service.

Whole controlling

of the unit stops

without cutting

main power or any

buttons

Might be influenced a strong noise

1. Avoid from the unit producing a strong noise or put away that.

2. If the problems do not solve, request the service.

Pr ess START/STOP

but t on but does not

wor k

Setting values of the controller trouble

1. After pressing SHAKE/SET button to input RPM setting value, press START/STOP

button to check operating condition.


the service.

Trouble related with mechanical shaking system Trouble Causes Solution

Occur trembleing

when acceleration,

deceleration and

uniform velocity

The shaker is not

equilibrated

Driving system troubles

1. Set the unit to keep its balance,

refer to the chapter 2.

2. If the problems do not solve, request the service.

Taking time to

reach the desired

RPM

Too many samples installed

on the shaking table.

1. Decrease the number of samples on the

shaking table.

Make bumping noise

when operting

Interference or loosing RPM

sensor or its fixing

bracket

Interference of inner circuit lines

Driving system troubles.


Differency between

setting RPM and

speed of the

shaking table

Tension of the drive belt

is loosing


Page 40

Chapter. 7

Specification

Confirm the shaker¡s specification and circuit diagram to check

the unit¡s functions. Read this to know its features and

specification, so test to meet its property.

The circuit diagram illustrates the shaker¡s component circuit.

Specification

Page 41

Specification

Model SK-300 SK-600 SK-71

Permissible

environmental condition

Temperature 5℃ to 40℃

Maximum relative humidity 80%

Altitude up to 2,000m,

Pollution degree 2

Motion Orbi t al (forward, backward, pause):Standard, Reci procat i ng:

Opt i on

Frequency 10 t o 300r pm

Amplitude 20, 30, 40mm avai l abl e

(30mm st andar d)

30,40,50,60,70mm

avai l abl e

(30mm standard)

Accuracy ¡ 1 at 100r pm

Controller Di gi t al aut o el ect r i c f eedback

Timer Run t i me(999hr 59mi n 59sec) ,

Pause, For war d & Backwar d(Max. 59mi n 50sec, Mi n. 10sec)

Driving system Br ushl ess DC mot or wi t h f eedback cont rol

Body Steel, 3.2t & 2.0t, powder coating Material

Platform Anodi zed al umi num pl at e, 4. 0t

External 410 X 490 X 160mm 510 X 595 X 160mm 820 X 610 X 170mm Size(WXDXH)

Platform 350 X 350mm 450 X 450mm 755 X 481mm

Electric requirements AC100V/50, 60HZ, AC120V/60Hz, AC220V/60Hz, AC230V/50Hz

100V 0. 4A

120V 0. 4A

220V 0. 2A

Power

consumption

230V 0.2A

Weight(net) 24kg 29kg 50kg

* Above the options could be changed without any notice in accordance with the quality and

efficiency improvement for the product.

Page 42

Chapter. 8

Warranty and Service

Jeio Tech¡s shakers can be protected by our warranty and

service standard. Except for the presented standards, others

would not be warranted

Warranty standard

General matter

Warranty exception

Service contact

Page 43

Warranty standard

1. Customer can get free warranty service for 1 year from the date of purchase

when the machine is broken while operating.

2. Customer can¡t get free warranty service in case of as below.

① If the machine is broken due to the Act¡s of God.

② If the machine is broken due to overuse of voltage

③ If there is some shock to the machine.

④ If the outer part is damaged by solvent

⑤ If the machine is broken without taking care of the ¡Notice¡ alerted

on the manual

⑥ If persons who are not under the authority of service of Jeio tech

fixed or changed parts of the machine

⑦ If the broken machine is due to customer¡s fault

3. Contact your regional dealer for after service.

General matter ① The term of guarantee about responsibility on manufacture is 1 year from purchase

work under.

Warranty exception Charge within the term of warranty if as follows.

Purchase date

Serial number

A trouble part and trouble state

Equipments use environment

A use mistake of a user

A mistake of treatment of a user and custody

Unfair change of usage, remodeling of a machine and acceptance

It is trouble by acts of God such as a fire, a brilliant

Trouble by the use that it did not keep operation manual

Documents

SK 영문 07.07.13~현재 -유효 - Cole-Parmer · 1. Check the front and rear sides of the unit under packed condition. 2. Carefully unpack the package. 3. Check with care any damage