Embed Size (px)
Citation preview
MODEL: PSDSK2
MODEL: PSDSK3
MODEL: PSDSK1
V5.0
SINGLE/DOUBLE / TRIPLE SHELF WALL MOUNT
Thank you for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if you are satisfied? Should you have any issues, please don't hesitate to contact us. Telephone：800-5566-806 Mon-Fri 10am - 6pm (PST) (USA) Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)
Stud Finder Pencil
1/8 in. (3.2 mm)Wood Drill Screw driver Hammer
Level
5/16 in. (8 mm)Concrete Drill
Drill
WARNING!
CAUTION!
!USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY. USER MUST REMOVE TELEVISION OR OBJECT OFF THE BRACKET BEFORE ADJUSTING. NOT SUITABLE FOR A TV THAT SURPASSES THE TELEVISION MAXIMUM WEIGHT CAPACITY AND RECOMMENDED DIAGONAL MEASURED TV SIZE!
*
*
*
*
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.If you do not understand the instructions or have any concerns or questions, please contact a qualified installer. Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you require replacement parts, contact customer service at [email protected] not attempt to install or assemble this product if the product or hardware is damaged or missing. The included hardware is designed for use on vertical walls constructed of wood studs or concrete. A wood stud wall is defined as consisting of a minimum of 2x4 wooden studs (2” wide by 4” deep) with a maximum of 5/8” drywall. The included hardware is not designed for use with metal studs or cinderblock walls. If you’re uncertain about the construction of your wall, then please consult a qualified contractor or installer for assistance. For a safe installation, the wall you are mounting to must support 4 times the weight of the total load. If not, then the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure and hardware used in any installation method will safely support the total load.
Find the stud by the stud finder and mark the center.
2
Use wall plate (A) to mark two mounting hole locations.
A
2
DCBA
X2X1PSDSK2 X2PSDSK1 X1
PSDSK3 X3
PSDSK2 X2PSDSK1 X1
PSDSK3 X3PSDSK2 X2PSDSK1 X1
PSDSK3 X3PSDSK2 X2PSDSK1 X1
PSDSK3 X3
Glass bracketHG
Ring
PSDSK2 X4PSDSK1 X2
PSDSK3 X6
PlugI
PSDSK2 X2PSDSK1 X1
Thread
PSDSK3 X3
Connector
E2
PSDSK2 X2PSDSK1 X1
PSDSK3 X3
Connector
E1
PSDSK2 X4PSDSK1 X2
PSDSK3 X4
Rubber pad AF1
W-A
Shelf Kit
PSDSK1 x2PSDSK2 x4PSDSK3 x6
Inner Hexagon ScrewM5x10 Allen Key
Lag Bolt
Cable manager End capGlass shelf
Concrete Anchor
S-CS-B
V3邮箱更改V4增加内容
PSDSK1 x2PSDSK2 x4PSDSK3 x6
S-A
Screw M5x12
Washer
C
PSDSK2 X4PSDSK1 X2
PSDSK3 X6
Rubber pad BF2
WEIGHT CAPACITY
Tools Needed
CONTENTS
1a. MOUNT WALL PLATE ON SINGLE STUD
Insert the cable manager into the wall bracket, then attach the end caps .
Drill pilot holes using a 1/8 in. (3.2 mm) diameter drill bit. Secure the wall mount with the lag bolt.
A
3 4
I
2 Paste the rubber pad B onto the glass bracket .
Peel off
F2
F2
F2
H
H
Secure the M5x12 screws and the connector to attach the glass brackets to the wall brackets. 1 S-A E1 E2
DB
D
B
Level
1/8
in.
Ø3.
2 m
m
2.2in. (55mm)
AE2
H
E2
E1
H
S-A
CAUTION: Secure the glass to the lower bracket at first, then secure the medium one(for PSDSK3), AT LAST secure the topper-level one.
Use wall bracket holes to mark 2 mounting locations. Use level to ensure proper alignment. if needed.
Secure 2 wall anchors into drilled holes with hammer.
Secure wall bracket to concrete wall using screws by phillips screwdriver.
W-A
W-B
W-C
1/8”(3.2mm)
2 (60mm)
3/8”(10mm)
2 3/8”(60mm)
Drill 2 pilot holes into concrete wall.
W-C
A
A
S-AB
Assemble the glass shelves at the glass brackets with screws .
Peel off
F1
C
H
S-B
S-CG
F1
F2
I
E1
Thread
1b. MOUNT WALL PLATE ON CONCRETE
2.
S-C3 HCAssemblare i ripiani in vetro alle staffe di
vetro con le viti .
3. End caps and cable manager installation
