Single-phase Micro-inverter Installation and User Manual€¦ · The APS M1P series Micro-inverters connect with the single-phase grid, and operate with most 60,72 cell PV modules

ALTENERGY POWER SYSTEM, INC.

1

APS M1P-SAA

Single-phase Micro-inverter

Installation and User Manual

Version: 4.0

!!


All rights reserved


2

Contact Information

ALTENERGY POWER SYSTEM Inc.

1 Yatai Road, Jiaxing, PR China 314050

Phone: +86-21-68889199

Fax: +86-21-33928752

www.altenergy-power.com

[email protected]


3

Table of Contents

1.! Important Safety Information ......................................................................................................................... 4!Safety Instructions .............................................................................................................................................. 4!

2.! APS Micro-inverter System Introduction ....................................................................................................... 5!3.! APS Single-phase Micro-inverter M1P series ................................................................................................ 7!4.! APS Micro-inverter System Installation ......................................................................................................... 9!

Required Parts and Tools from you .................................................................................................................... 9!Installation Procedures .......................................................................................................................................10!

Step 1 - Installing the AC Branch Circuit AC Isolator ...................................................................................10!Step 2 – Attaching the APS Micro-inverters to the Racking or the PV Module Frame ................................. 11!Step 3 - Connecting the APS Micro-inverter AC Cables ...............................................................................12!Step 4 –Connecting APS Micro-inverters to the PV Module .........................................................................12!Step 5 - Completing the APS Installation Map ..............................................................................................13!

5.! APS micro-inverter system operating instructions ........................................................................................14!6.! Troubleshooting .............................................................................................................................................15!

Status Indications and Error Reporting ..............................................................................................................15!Operation LED ..............................................................................................................................................15!Other Faults ...................................................................................................................................................15!

7.! Replace a micro-inverter ................................................................................................................................17!8.! Efficiency Curves ..........................................................................................................................................18!9.! Technical Data ...............................................................................................................................................19!10.! Wiring Diagram .........................................................................................................................................22!

10.1! Sample Wiring Diagram – Single Phase ...............................................................................................22!10.2! Sample Wiring Diagram – Three Phase ................................................................................................23!


4

!" #$%&'()*(+,)-.(/+#*-&'$)(0&*+

This manual contains important instructions to follow during installation and maintenance of

the APS Photovoltaic Grid-connection Micro-inverter. To reduce the risk of electrical shock

and ensure the safe installation and operation of the APS Micro-inverter, the following

symbols appear throughout this document to indicate dangerous conditions and important

safety instructions.

WARNING: This indicates a situation where failure to follow instructions may

cause a serious hardware failure or personnel danger if not applied

appropriately. Use extreme caution when performing this task.

NOTE: This indicates information that is important for optimized

Micro-inverter operation. Follow these instructions closely.

!"#$%&'()*%+,-%./)*'

• Only qualified professionals should install and/or replace APS Micro-inverters.

• Perform all electrical installations in accordance with local electrical codes.

• Before installing or using the APS Micro-inverter, please read all instructions and

cautionary markings in the technical documents and on the APS Micro-inverter

system and the PV-array.

• Be aware that the body of the APS Micro-inverter is the heat sink and can reach a

temperature of 80°C. To reduce risk of burns, do not touch the body of the

Micro-inverter.

• Do NOT disconnect the PV module from the APS Micro-inverter without first

disconnecting the AC power.

• Do NOT attempt to repair the APS Micro-inverter. If it fails, contact APS Customer

Support to obtain an RMA number and start the replacement process. Damaging or

opening the APS Micro-inverter will void the warranty.


5

1" 23,+405'&60*7.'(.'+,/8(.$+#*('&9:5(0&*+

The APS Micro-inverter is an inverter system for use in utility-interactive applications,

comprised of three key elements:

• Altenergy Power Systems Micro-inverter

• Altenergy Power Systems Energy Communication Unit (ECU)

• Altenergy Power Systems Energy Monitor and Analysis (EMA) web-based monitoring

and analysis system

This integrated system improves safety; maximizes solar energy harvest; increases system

reliability; simplifies photovoltaic (PV) system design, installation, maintenance, and

management.

The APS Micro-inverters maximize energy production from photovoltaic (PV)

arrays. Each PV module has individual Maximum Peak Power Tracking (MPPT) controls,

which ensures that the maximum power is exported to the utility grid regardless of the

performance of the other PV modules in the array. When PV modules in the array are affected

by shading, soiling, orientation, or mismatch, the APS Micro-inverter ensures top

performance from the array by maximizing the performance of each module within the array.

The APS Micro-inverter system is more reliable than centralized or string inverters.

The distributed Micro-inverter system ensures that no single point of system failure exists

across the PV system. APS Micro-inverters are designed to operate at full power at ambient


6

temperatures of up to 65°C. The inverter housing is designed for outdoor installation and

complies with the IP65 environmental enclosure rating.

PV systems using APS Micro-inverters are very simple to install. You can install

individual PV modules in any combination of module quantity, orientation, type, and power

rate. The Ground wire (PE) of the AC cable is connected to the chassis inside of the

Micro-inverter, eliminating the installation of grounding wire.

The APS Micro-inverter system provides smart system performance monitoring

and analysis.

The APS Energy Communication Unit (ECU) is installed by simply plugging it into any wall

outlet and providing an Ethernet or Wi-Fi connection to a broadband router or modem. After

installing the ECU, the full network of APS Micro-inverters automatically reports to the APS

Energy Monitor and Analysis (EMA) web server. The EMA software displays performance

trends, informs you of abnormal events, and controls system shutdown when it is needed.


7

!" 23,+,0*;<.6%=)8.+405'&60*7.'(.'+4!3+8.'0.8#

The APS M1P series Micro-inverters connect with the single-phase grid, and operate with

most 60,72 cell PV modules. For more information, please see the section 8 Technical Date of

this manual.

Model

Number

AC grid PV Module

Max. #

Per branch

Module Connector

YC250A 50Hz/230V 60,72 Cell

14 for 20A

breaker

MC-4 Type or Customize

YC250I 50Hz/230V 60,72 Cell

14 for 20A

breaker


YC500A 50Hz/230V 60,72 Cell

7 for 20A

breaker


YC500I 50Hz/230V 60,72 Cell

7 for 20A

breaker


YC250A 50Hz/230V 60,72 Cell

18 for 25A

breaker


YC250I 50Hz/230V 60,72 Cell

18 for 25A

breaker


YC500A 50Hz/230V 60,72 Cell

9 for 25A

breaker


YC500I 50Hz/230V 60,72 Cell

9 for 25A

breaker



8

The following figure shows the APS YC250 micro-inverter schematic:!!!

APS YC500 has two independent DC inputs, with independent MPPT control and

data monitoring.

The following figure shows the APS YC500 micro-inverter schematic:

!!!


9

>" 23,+405'&60*7.'(.'+,/8(.$+#*8()<<)(0&*+

A PV system using APS Micro-inverters is simple to install. Each Micro-inverter easily mounts

on the PV racking, directly beneath each PV module. Low voltage DC wires connect from the

PV module directly to the Micro-inverter, eliminating the risk of high DC voltage.

Installation shall comply with local regulations and technical rules. Installation shall comply

with the relevant instructions of AS 4777.1 /.2& AS 3000.

WARNING: Perform all electrical installations in accordance with local electrical

codes.

WARNING: Be aware that only qualified professionals should install and/or

replace APS Micro-inverters.

WARNING: Before installing or using an APS Micro-inverter, please read all

instructions and warnings in the technical documents and on the APS

Micro-inverter system itself as well as on the PV array.

WARNING: Be aware that installation of this equipment includes the risk of

electric shock.

WARNING: Do not touch any live parts in the system, including the PV array,

when the system has been connected to the electrical grid.

WARNING: Affix warning labels to micro system components where and as

appropriate for your state/territory.

011.%./)"2'()*%"22"%./)'3/45/)$)%*'#+/4'06!

• Protective branch end cap (sold separately, 1 per branch)

• AC branch end cable (sold separately, 1 per branch)

7$8,.+$1'6"+%*'")1'9//2*'#+/4'&/,'

In addition to your PV array and its associated hardware, you need to provide the following:

• An AC isolator

• Mounting hardware suitable for module racking

• Sockets and wrenches for mounting hardware

• A Phillips screwdriver

• A torque wrench


10

()*%"22"%./)'6+/-$1,+$*'

WARNING: Do NOT connect APS Micro-inverters to the utility grid or energize

the AC circuit until you have completed all of the installation procedures as

described in the following sections.

For bracket installation, after the completion of system installation rendering as follows:

!!!"#$%&%'%()*"+,,-).%"/#%01%23+)4/%1-345-"%01%(*6,+"63%

a. Install an appropriate AC isolator at a suitable location on the PV racking system

(typically at the end of a branch of modules).

b. Connect the open wire end of the AC branch end cable into the AC isolator using an

appropriate gland or strain relief fitting.

c. Wire the conductors: L- RED; N - BLACK; PE – YELLOW GREEN.

d. Connect the AC branch circuit AC isolator to the point of utility interconnection.

NOTE: Be sure to size the AC wire to account for voltage drop between the

AC branch circuit AC isolator and the point of utility interconnection. Refer to

the tables below.

Go to distribution box


11

!!

% % % % % % % % %

!"#$%7%8%0""+4/-).%"/#%09!%:-436'-);#3"#3*%"6%"/#%<+4=-).%63%"/#%9>%:6?5,#%

@3+A#% %

!!!!!!!!!!!! !a. Mark the location of the Micro-inverter on the rack, with respect to the PV module AC

isolator or any other obstructions.

b. Mount one Micro-inverter at each of these locations using hardware recommended by

your module racking vendor.

WARNING: Prior to installing any of the micro-inverters, verify that the utility

voltage at the point of common connection matches the voltage rating on

micro-inverter label.

WARNING: Do not mount the Micro-inverter in a location that allows

exposure to direct sunlight. Allow a minimum of 1.5 centimeters between the

top of the roof and the bottom of the Micro-inverter.


12

!"#$%B%'%16))#4"-).%"/#%09!%:-436'-);#3"#3%01%1+C,#*% !!

a. Check the Micro-inverter rating label for the maximum allowable number of

Micro-inverters on one AC branch circuit.

b. Plug the AC female connector of the first Micro-inverter into the male connector of the

next Micro-inverter, and so on, to form a continuous AC branch circuit.

c. Install a protective branch end cap on the open AC connector of the last

Micro-inverter in the AC branch circuit.

!!!!!! !!

WARNING: Do NOT exceed the maximum number of Micro-inverters in an AC

branch circuit, as displayed on the unit label.

!"#$%D%816))#4"-).%09!%:-436'-);#3"#3*%"6%"/#%9>%:6?5,#%

Photovoltaic panels and micro-inverter DC input cable connection according to demand.!!! !!


13

WARNING: Ensure that all AC and DC wiring is correct. Ensure that none of the

AC and DC wires are pinched or damaged. Ensure that all AC isolator are

properly closed.

NOTE: Step 1~4 can change sequence for convenience of installation.

!"#$%E%'%16A$,#"-).%"/#%09!%()*"+,,+"-6)%:+$%

You need to fill-in APS Warranty Cards, which provide system information and installation

map. Feel free to provide your own layout if a larger or more intricate installation map is

required.

a. Each APS Micro-inverter has removable serial number labels. Peel a label off, and affix it

to the respective location on the APS installation map.

b. Fill the warranty cards and email to APS at [email protected].

c. APS will setup the EMA account and email you information, and then you can use the EMA

website to view detailed performance of your PV system.

!!!!!!!!!!!!!! !


14

?" + 23,+$05'&60*7.'(.'+8/8(.$+&%.')(0*;+0*8(':5(0&*8+

To operate the APS micro-inverter PV system:

1. Turn ON the AC circuit breaker on each micro-inverter AC branch circuit.

2. Turn ON the main utility-grid AC circuit breaker. Your system will start producing power

after a two-minute waiting time.

Note: Once DC power is applied, the Status LED of each micro-inverter will

blink green three times to indicate normal start-up operation.

3. The APS micro-inverters will start to send performance data over power line to the ECU.

The time required for all the micro-inverters in the system to report to the ECU will vary with

the number of micro-inverters in the system. You can verify proper operation of the APS

micro-inverters via the ECU. See the ECU Installation and Operation Manual for more

information.


15

@" + A'&:B<.8=&&(0*;+Qualified personnel can use the following troubleshooting steps if the PV system does not

operate correctly.

!%"%,*'()1.-"%./)*'")1':++/+'7$5/+%.);'

!"+3"5$%FGH%

When DC power is first applied to the micro-inverter:

• Three short green blinks when DC power is first applied to the micro-inverter indicate

a successful micro-inverter startup

I$#3+"-6)%FGH%

Flashing Slow Green (10s gap) - Producing power and communicating with ECU

Flashing Fast Green (2s gap) – Producing power and not communicating with ECU

Flashing Red – Not producing power

I"/#3%@+5,"*%

All other faults are reported to the ECU. Refer to the ECU Installation and Operation Manual

for a list of additional faults and troubleshooting procedures.

WARNING: Be aware that only qualified personnel should troubleshoot the

APS micro-inverter.

WARNING: Never disconnect the DC wire connectors under load. Ensure that

no current is flowing in the DC wires prior to disconnecting. An opaque covering

may be used to cover the module prior to disconnecting the module.

WARNING: Always disconnect AC power before disconnecting the PV module

wires from the APS micro-inverter. The AC connector of the first micro-inverter

in a branch circuit is suitable as a disconnecting means once the AC branch

circuit breaker in the load center has been opened.

WARNING: The APS micro-inverter is powered by PV module DC power. Make

sure you disconnect and reconnect the DC connections to watch for the three

short LED flashes.

9+/,<2$*=//%.);'"')/)>/5$+"%.);'06!'4.-+/>.)?$+%$+' '

To troubleshoot a non-operating APS micro-inverter, follow the steps below in order:

!" Verify the utility voltage and frequency are within ranges shown in the in section 8

Technical Data of this manual.

#" Check the connection to the utility grid. Verify utility power is present at the inverter

in question by removing AC, then DC power. Never disconnect the DC wires while


16

the micro-inverter is producing power. Re-connect the DC module connectors

and watch for three short LED flashes.

$" Check the AC branch circuit interconnection between all the micro-inverters. Verify

each inverter is energized by the utility grid as described in the previous step.

%" Make sure that any AC breaker are functioning properly and are closed.

&" Check the DC connections between the micro-inverter and the PV module.

'" Verify the PV module DC voltage is within the allowable range shown in the Section 8

Technical Data of this manual.

(" If the problem persists, please call APS Energy customer support.

WARNING: Do not attempt to repair the APS micro-inverter. If troubleshooting

methods fail, please return the micro-inverter to your distributor for

replacement.


17

C" + D.%<)5.+)+$05'&60*7.'(.'+Follow the procedure to replace a failed APS micro-inverter.

1. Disconnecting the APS micro-inverter from the PV Module, in the order shown below:

1) Disconnect the AC by opening the branch circuit breaker.

2) Cover the module with an opaque cover.

3) Disconnect the first AC connector in the branch circuit.

4) Disconnect the PV module DC wire connectors from the micro-inverter.

5) Remove the micro-inverter from the PV array racking.

2. Install a replacement micro-inverter to the rack.

3. Connect the AC cable of the replacement micro-inverter and the neighboring

micro-inverters to complete the branch circuit connections.

4. Close the branch circuit breaker, and verify operation of the replacement

micro-inverter.


18

E" F--050.*5/+G:'7.8+

YC500 Efficiency-temperature Curves

YC500 Efficiency Curves


19

H" + A.5=*05)<+I)()+

WARNING: Be sure to verify the voltage and current specifications of your PV

module match with those of the micro-inverter. Refer to the APS website

http://www.altenergy-power.com for a list of approved PV modules.

WARNING: You must match the DC operating voltage range of the PV module

with the allowable input voltage range of the APS micro-inverter.

WARNING: The maximum open circuit voltage of the PV module must not

exceed the specified maximum input voltage of the APS micro-inverter.


20

YC250A/YC250I Technical Specifications (SAA)

Type YC250A/YC250I

Input Data (DC) Recommended PV Module Power (STC)Range 180-310W

MPPT Voltage Range 22-45VDC

MPPT Voltage Range @ Full Power 26-45VDC

Maximum Input Voltage 55VDC

Startup Voltage 22V

Maximum Input Current 10.5A

Output Data (AC) Maximum Continuous Power 250W

Maximum Continuous Current 1.08A

Rated Grid Voltage 230VAC

Default Output Voltage Range 200V-270V1

Extended Output Voltage Range 149V-278V

Rated Grid Frequency 50Hz

Default Output Frequency Range 47.5Hz-50.5Hz 1

Extended Output Frequency Range 45.1Hz -54.9Hz

Power Factor >0.99

Total Harmonic Distortion <3%

Maximum Units per Branch! 14 for 20A Breaker/18 for 25A Breaker

Efficiency Max. Inverter Efficiency 95.5% (With HF Transformer)

Mechanical Data Operating Ambient Temperature -40

°C to +65°C

Operating Internal Temperature -40

°C to +85°C

Storage Temperature Range -40

°C to +85°C

Dimensions (W x H x D) 160mmX 150mmX 29mm

Weight 1.5kg

Waterproof Level IP65

Cooling Natural Convection

Wet Locations Classification For Wet Locations

Pollution Degree Classification PD3

Relative Humidity Ratings 0-95%

Maximum Altitude Rating

All data at this technical Specifications

has been tested under <2000m

Overvoltage Category OVC II for PV input circuit, OVC III for mains circuit

Features & Compliance Communication Power Line

Design Lifetime 25yrs

Grid Connection Compliance AS 4777.2/AS 4777.3

Safety Class Compliance! EN 62109-1; EN 62109-2;AS3100

1

Programmable through ECU to meet customer need.

The specifications are subject to change without notice.#


21

YC500A/YC500I Technical Specifications (SAA)

Type!!!! YC500A/YC500I(for 2 panels)

Input Data (DC)

Recommended PV module power (STC) range 180-310W

MPPT voltage range 22-45VDC

MPPT Voltage Range @ Full Power 26-45VDC

Maximum Input Voltage 55VDC

Startup Voltage 22V

Maximum Input Current 10.5AX2

Output Data (AC) Maximum Continuous Power 500W

Maximum Continuous Current 2.17A

Rated Grid Voltage 230VAC

Default Output Voltage Range 200V-270V1

Extended Output Voltage Range 149V-278V

Rated Grid Frequency 50Hz

Default Output Frequency Range 47.5Hz-50.5Hz1

Extended Output Frequency Range 45.1Hz -54.9Hz

Power Factor >0.99

Total Harmonic Distortion <3%

Maximum Units per Branch! 7 for 20A Breaker/9 for 25A Breaker

Efficiency

Max. Inverter Efficiency 95.5% (with HF Transformer)

Mechanical Data

Operating Ambient Temperature -40°C to +65°C

Operating Internal Temperature -40ºC to +85ºC

Storage Temperature Range -40ºC to +85ºC

Dimensions (W x H x D) 221mm X 167mm X 29mm

Weight 2.5kg

Waterproof Level IP65

Cooling Natural Convection

Wet Locations Classification For Wet Locations

Pollution Degree Classification PD3

Relative Humidity Ratings 0-95%

Maximum Altitude Rating

All data at this technical Specifications has been

tested under <2000m

Overvoltage Category OVC II for PV input circuit, OVC III for mains circuit

Features & Compliance

Communication Power Line

Design Lifetime 25yrs

Grid Connection Compliance AS 4777.2/AS 4777.3

Safety Class Compliance! EN 62109-1; EN 62109-2;AS3100

1

Programmable through ECU to meet customer need.

The specifications are subject to change without notice.


22

!J" K0'0*;+I0);')$+

@AB@ ' !"452$'C.+.);'D.";+"4'E'!.);2$'6="*$'

!


23

@ABF ' !"452$'C.+.);'D.";+"4'E'9=+$$'6="*$'

!

Documents

Single-phase Micro-inverter Installation and User Manual€¦ · The APS M1P series Micro-inverters connect with the single-phase grid, and operate with most 60,72 cell PV modules