SIMOCODE pro - Siemens Guide usa.siemens.com/mcc SIMOCODE pro ... This is a specific selection as to how SIMOCODE pro is placed ... (Cyclic Receive Bit 0.5) sets SIMOCODE pro …

Selection Guide

usa.siemens.com/mcc

SIMOCODE proParameterization selection in COMPAS

SIMOCODE pro | Parameterization selection in COMPAS

3

Parameterization selection in COMPAS | SIMOCODE pro

Introduction

This document is intended to define and demonstrate the necessary knowledge to select parameterization of SIMOCODE pro in a low-voltage motor control center (LV MCC). When configuring an LV MCC in COMPAS with the SIMOCODE pro overload relay, there are extra factors that need to be considered over a standard overload relay. The COMPAS configuration tool has several selections that allow for varied parameterization levels of the SIMOCODE pro overload.

SIMOCODE pro is a powerful device with a myriad of options. The following selections are aimed at providing a solid foundation for our customers. Monitoring and diagnostic parameters of the SIMOCODE pro are meant to be commissioned by the end user to suit their specific needs.

Structure

The parameterization selections fall into three categories: Parameter Level, Network Mode Selector and Control Scheme (Local/Remote). Selection works by moving from Parameter Level to Network Mode Selector and then lastly to Control Scheme (Local/Remote). Below is a table of the selections and how they are linked together.

Parameter Level Network Mode Selector Control Scheme (Local/Remote)

Basic Checks Network Connectivity Check Device Configuration Check

Standard Parameter Blocks Overload Relay w/ Remote I/O Any/Maintained Network Bits

Standard Parameter Blocks Network Bit None/Maintained Bits

Standard Parameter Blocks Network Bit None/Momentary Bits

Standard Parameter Blocks Network Bit Momentary OP/Maintained Bits

Standard Parameter Blocks Network Bit Momentary OP/Momentary Bits

Standard Parameter Blocks Network Bit Maintained SS/Maintained Bits

Standard Parameter Blocks Network Bit Maintained SS/Momentary Bits

Standard Parameter Blocks Network Bit Momentary PB/Maintained Bits

Standard Parameter Blocks Network Bit Momentary PB/Momentary Bits

Standard Parameter Blocks Operator Panel Button Momentary OP/Maintained Bits

Standard Parameter Blocks Operator Panel Button Momentary OP/Momentary Bits

Standard Parameter Blocks Selector Switch Maintained SS/Maintained Bits

Standard Parameter Blocks Selector Switch Maintained SS/Momentary Bits

Standard Parameter Blocks Selector Switch Momentary PB/Maintained Bits

Standard Parameter Blocks Selector Switch Momentary PB/Momentary Bits

Custom Parameter Blocks Custom with Consultation Custom with Consultation

Each of these selections is explained in detail further in the document.

4


Step One: Parameter Level

This is a general selection on the depth of parameterization as shipped. The three choices are:

1. BASIC CHECKS:

a. Customer will perform the entire parameterization of the SIMOCODE pro overload.

b. Customer will receive a SIMOCODE pro overload that has had a network connectivity check and device configuration check performed at manufacturing facility.

c. Each device will have been parameterized with a network address and device configuration of the attached SIMOCODE components.

d. This provides verification that all of the components and cabling for the SIMOCODE pro and communication network are functional upon shipment to the customer’s site.

2. STANDARD PARAMETER BLOCKS:

a. Customer will perform the commissioning parameterization of the SIMOCODE pro overload.

b. In addition to the BASIC CHECKS, customer will receive a SIMOCODE pro overload that has had a STANDARD PARAMETER BLOCK check performed.

c. Each device will have been parameterized with a network address, device configuration, network mode selector, and standard control scheme.

d. This provides verification that all of the components and cabling for the control devices, SIMOCODE pro, and communication network are functional as a system upon shipment to the customer’s site.

3. CUSTOM PARAMETER BLOCKS:

a. Customer is requesting to consult with an LV MCC Systems Engineer for a fee to develop a customized solution. User will perform the commissioning parameterization of the SIMOCODE pro overload.

b. In addition to the BASIC CHECKS, customer will receive a SIMOCODE pro overload that has had a CUSTOM PARAMETER BLOCK check performed.

c. Each device will have been parameterized with a network address, device configuration, network mode selector, and custom control scheme.

d. This provides verification that all of the components and cabling for the control devices, SIMOCODE pro, and communication network are functional as a system upon shipment to the customer’s site.

5


Step Two: Network Mode Selector

This is a specific selection as to how SIMOCODE pro is placed into remote control mode where operating signals are given over networked communication. The choices for this will vary depending on the PARAMETER LEVEL selection.

1. BASIC CHECKS:

a. There is only the default choice of NETWORK CONNECTIVITY CHECK as the user is agreeing to perform the entire parameterization of the SIMOCODE pro.


a. OVERLOAD RELAY W/ REMOTE I/O:

i. Customer will receive a SIMOCODE pro parameterized to work as a basic electronic overload relay without motor control functionality.

ii. There is no method to place the SIMOCODE pro into a remote operating mode.

iii. All control decisions are made external to the SIMOCODE pro.

iv. SIMOCODE pro inputs and outputs are available for use as networked communication I/O in place of traditional hardwired I/O.

b. NETWORK BIT:

i. Customer will receive a SIMOCODE pro parameterized to work as an overload relay with motor controller functionality.

ii. The method to place the SIMOCODE pro into a remote operating mode is achieved by sending a maintained network bit (Cyclic Receive Bit 0.5) over the networked communication.

iii. Loss of the maintained network bit (Cyclic Receive Bit 0.5) sets SIMOCODE pro to local operating mode.

c. OPERATOR PANEL BUTTON:


ii. The method to place the SIMOCODE pro into a remote operating mode is achieved by toggling Button 1 on the SIMOCODE pro keypad.

iii. A successive toggling of Button 1 on the SIMOCODE pro keypad will set the SIMOCODE pro to local operating mode.

d. SELECTOR SWITCH:


ii. The method to place the SIMOCODE pro into a remote operating mode is achieved by setting the HAND-OFF-AUTO maintained selector switch to the AUTO position.

iii. Setting the HAND-OFF-AUTO maintained selector switch to the HAND or OFF positions will set the SIMOCODE pro to local operating mode.

3. CUSTOM PARAMETER BLOCKS:

a. There is only the default choice of CUSTOM with CONSULTATION as the customer is requesting to consult with an LV MCC Systems Engineer for a fee.

6


Step Three: Control Scheme (Local / Remote)

This is a specific selection as to the controls and network communication signals required for SIMOCODE pro to operate in the LOCAL and REMOTE control modes. The two are separated by a forward slash character with the local mode control appearing ahead of the slash and the Remote mode control appearing after the slash. The choices for this will vary depending on the Parameter Level and Network Mode Selector selections.

1. BASIC CHECKS:

a. There is only the default choice of DEVICE CONFIGURATION CHECK as the customer is agreeing to perform the entire parameterization of the SIMOCODE pro.


a. OVERLOAD RELAY W/ REMOTE I/O:

i. ANY/MAINTAINED NETWORK BITS (see Figure 1):

1. ANY:

a. Traditional control schemes may be used as the SIMOCODE pro is set for use as an overload, diagnostics and remote I/O device instead of a motor control management device.

b. SIMOCODE pro Output 3 is configured as a normally closed overload contact to protect the motor.

c. Note: Multiple speed motors require the use of two SIMOCODE pro devices like a traditional circuit would since the motor control management portion has been defeated.

2. MAINTAINED NETWORK BITS:

a. Continuous signal(s) may be sent over the network to energize SIMOCODE pro output(s).

b. SIMOCODE pro Outputs (Basic Unit Output 1, Basic Unit Output 2) are tied to network signals (Cyclic Receive Bit 0.1, Cyclic Receive Bit 0.2) for use as remote relay outputs.

c. SIMOCODE pro Inputs (Basic Unit Input 1, Basic Unit Input 2, Basic Unit Input 3, Basic Unit Input 4) are tied to network signals (Cyclic Send Bit 0.1, Cyclic Send Bit 0.2, Cyclic Send Bit 0.3, Cyclic Send Bit 0.4) for use as remote inputs.

7


Figure 1

Step Three: Control Scheme (Local / Remote) (continued)

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

RE

V

FWD

11A

23

45

6

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A2

3

6

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL1

SLO

W

FAS

T

FAS

T

SLO

W

11A

23

45

6

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL1

SLO

W

SH

OR

T

FAS

T

SLO

W

11A

23

45

6

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL2

FAS

T

SH

OR

T

SH

OR

TO

L1O

UT1

LIN

KE

D T

O C

YC

LIC

RE

CE

IVE

BIT

0.1

OU

T2 L

INK

ED

TO

CY

CLI

C R

EC

EIV

E B

IT 0

.2IN

1 LI

NK

ED

TO

CY

CLI

C S

EN

D B

IT 0

.1IN

2 LI

NK

ED

TO

CY

CLI

C S

EN

D B

IT 0

.2IN

3 LI

NK

ED

TO

CY

CLI

C S

EN

D B

IT 0

.3IN

4 LI

NK

ED

TO

CY

CLI

C S

EN

D B

IT 0

.4

OL2

OU

T1 L

INK

ED

TO

CY

CLI

C R

EC

EIV

E B

IT 0

.1O

UT2

LIN

KE

D T

O C

YC

LIC

RE

CE

IVE

BIT

0.2

IN1

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.1

IN2

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.2

IN3

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.3

IN4

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.4

OL1

OU

T1 L

INK

ED

TO

CY

CLI

C R

EC

EIV

E B

IT 0

.1O

UT2

LIN

KE

D T

O C

YC

LIC

RE

CE

IVE

BIT

0.2

IN1

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.1

IN2

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.2

IN3

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.3

IN4

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.4

OL2

OU

T1 L

INK

ED

TO

CY

CLI

C R

EC

EIV

E B

IT 0

.1O

UT2

LIN

KE

D T

O C

YC

LIC

RE

CE

IVE

BIT

0.2

IN1

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.1

IN2

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.2

IN3

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.3

IN4

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.4

OL1

OU

T1 L

INK

ED

TO

CY

CLI

C R

EC

EIV

E B

IT 0

.1O

UT2

LIN

KE

D T

O C

YC

LIC

RE

CE

IVE

BIT

0.2

IN1

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.1

IN2

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.2

IN3

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.3

IN4

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.4

OL1

OU

T1 L

INK

ED

TO

CY

CLI

C R

EC

EIV

E B

IT 0

.1O

UT2

LIN

KE

D T

O C

YC

LIC

RE

CE

IVE

BIT

0.2

IN1

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.1

IN2

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.2

IN3

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.3

IN4

LIN

KE

D T

O C

YC

LIC

SE

ND

BIT

0.4

X2

X2

X2

8



b. NETWORK BIT:

i. NONE/MAINTAINED BITS (see Figure 2):

1. NONE:

a. Local control commands are not parameterized.

2. MAINTAINED BITS:

a. Remote control commands are continuous signals sent over the network to engage the motor controller functionality.

b. Motor start will occur when the continuous command signal (Cyclic Receive Bit 0.2, Cyclic Receive Bit 0.0) is present.

c. Loss of the continuous command signal will result in an OFF condition.

ii. NONE/MOMENTARY BITS (see Figure 2):

1. NONE:

a. Local control commands are not parameterized.

2. MOMENTARY BITS:

a. Remote control commands are brief signals sent over the network to engage the motor controller functionality.

b. Motor start will occur when the brief command signal (Cyclic Receive Bit 0.2, Cyclic Receive Bit 0.0) is present.

c. Motor stop will occur when the brief command signal (Cyclic Receive Bit 0.1) is present.

9



L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

11A

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A

X2

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

SH

OR

T

Figure 2

10



iii. MOMENTARY OP/MAINTAINED BITS (see Figure 3):

1. MOMENTARY OP:

a. Local control commands are brief presses of the Operator Panel buttons to engage the motor controller functionality.

b. Motor start will occur when the required brief press of the Operator Panel button (Button 2, Button 3) is present.

c. Motor stop will occur when the required brief press of the Operator Panel button (Button 4) is present.

2. MAINTAINED BITS:



c. Loss of the continuous command signal will result in an off condition.

iv. MOMENTARY OP/MOMENTARY BITS (see Figure 3):

1. MOMENTARY OP:

a. Local control commands are brief presses of the Operator Panel buttons to engage the motor controller functionality.

b. Motor start will occur when the required brief press of the Operator Panel button (Button 2, Button 3) is present.

c. Motor stop will occur when the required brief press of the Operator Panel button (Button 4) is present.

2. MOMENTARY BITS:




11



L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

11A

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A

X2

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

SH

OR

T

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

NO

FU

NC

TIO

N

NO

FU

NC

TIO

N

STA

RT

STO

P

NO

FU

NC

TIO

N

RE

V

FWD

STO

P

NO

FU

NC

TIO

N

FAS

T

SLO

W

STO

P

NO

FU

NC

TIO

N

FAS

T

SLO

W

STO

P

OP

ER

ATO

R P

AN

EL

LEG

EN

DO

PE

RA

TOR

PA

NE

L LE

GE

ND

OP

ER

ATO

R P

AN

EL

LEG

EN

D

OP

ER

ATO

R P

AN

EL

LEG

EN

D

Figure 3

12



v. MAINTAINED SELECTOR SWITCH (SS)/MAINTAINED BITS (see Figure 4):

1. MAINTAINED SS:

a. Local control commands are continuous positioning of the selector switch to engage the motor controller functionality.

b. Motor start will occur when the required continuous positioning of the selector switch (ON, FWD, REV, SLOW, FAST) is present.

c. Motor stop will occur when the required continuous positioning of the selector switch (OFF) is present.

2. MAINTAINED BITS:




vi. MAINTAINED SS/MOMENTARY BITS (see Figure 4):

1. MAINTAINED SS:


b. Motor start will occur when the required continuous positioning of the selector switch (ON, FWD, REV, SLOW, FAST) is present.


2. MOMENTARY BITS:




13



L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

11A

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A

X2

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

SH

OR

T

OFF

ON X

FWD

OFF

RE

V

X

X

SLO

W O

FF F

AS

T

X

X

SLO

W O

FF F

AS

T

X

X

Figure 4

14



vii. MOMENTARY PB/MAINTAINED BITS (see Figure 5):

1. MOMENTARY PB:

a. Local control commands are brief presses of the pushbuttons to engage the motor controller functionality.

b. Motor start will occur when the a brief press of the appropriate pushbutton (START, FWD, REV, SLOW, FAST) is present.

c. Motor stop will occur when the brief press of the appropriate pushbutton (STOP) is present.

2. MAINTAINED BITS:




viii. MOMENTARY PB/MOMENTARY BITS (see Figure 5):

1. MOMENTARY PB:


b. Motor start will occur when the a brief press of the appropriate pushbutton (START, FWD, REV, SLOW, FAST) is present.

c. Motor stop will occur when the required brief press of the appropriate pushbutton (STOP) is present.

2. MOMENTARY BITS:




15



L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

11A

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A

X2

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

SH

OR

T

STA

RT

STO

P

FWD

STO

P

RE

V

SLO

W

STO

P

FAS

T

SLO

W

STO

P

FAS

T

Figure 5

16



c. OPERATOR PANEL BUTTON:

i. MOMENTARY OP/MAINTAINED BITS (see Figure 6):

1. MOMENTARY OP:

a. Local control commands are brief presses of the operator panel buttons to engage the motor controller functionality.

b. Motor start will occur when the required brief press of the operator panel button (Button 2, Button 3) is present.

c. Motor stop will occur when the required brief press of the operator panel button (Button 4) is present.

2. MAINTAINED BITS:




ii. MOMENTARY OP/MOMENTARY BITS (see Figure 6):

1. MOMENTARY OP:

a. Local control commands are brief presses of the operator panel buttons to engage the motor controller functionality.

b. Motor start will occur when the required brief press of the operatorpanel button (Button 2, Button 3) is present.

c. Motor stop will occur when the required brief press of the operator panel button (Button 4) is present.

2. MOMENTARY BITS:




17



L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

11A

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A

X2

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

SH

OR

T

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

DE

VIC

EB

US

GE

N F

AU

LT

TES

TR

ES

ET

DE

VIC

E

BU

S

GE

NFA

ULT

OP

ER

ATO

R P

AN

EL

OP

ER

ATO

R P

AN

EL

W/ D

ISP

LAY

OR

RE

MO

TE M

OD

E

NO

FU

NC

TIO

N

STA

RT

STO

P

RE

MO

TE M

OD

E

RE

V

FWD

STO

P

RE

MO

TE M

OD

E

FAS

T

SLO

W

STO

P

RE

MO

TE M

OD

E

FAS

T

SLO

W

STO

P

OP

ER

ATO

R P

AN

EL

LEG

EN

DO

PE

RA

TOR

PA

NE

L LE

GE

ND

OP

ER

ATO

R P

AN

EL

LEG

EN

D

OP

ER

ATO

R P

AN

EL

LEG

EN

D

Figure 6

18



d. SELECTOR SWITCH:

i. MAINTAINED SS/MAINTAINED BITS (see Figure 7):

1. MAINTAINED SS:


b. Motor start will occur when the required continuous positioning of the selector switch (HAND, FWD, REV, FAST, SLOW) is present.


2. MAINTAINED BITS:




ii MAINTAINED SS/MOMENTARY BITS (see Figure 7):

1. MAINTAINED SS:


b. Motor start will occur when the required continuous positioning of the selector switch (HAND, FWD, REV, FAST, SLOW) is present.


2. MOMENTARY BITS:




19



L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

11A

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A

X2

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

SH

OR

T

HA

ND

OFF

AU

TO

X

X

X

FWD

RE

V

X

HA

ND

OFF

AU

TO

X

X

HA

ND

OFF

AU

TO

X

X

X

SLO

W F

AS

T

X

HA

ND

OFF

AU

TO

X

X

X

SLO

W F

AS

T

X

Figure 7

20



iii. MOMENTARY PB/MAINTAINED BITS (see Figure 8):

1. MOMENTARY PB:


b. Motor start will occur when the brief press of the appropriate pushbutton (START, FWD, REV, SLOW, FAST) is present.


2. MAINTAINED BITS:




iv. MOMENTARY PB/MOMENTARY BITS (see Figure 8):

1. MOMENTARY PB:


b. Motor start will occur when the brief press of the appropriate pushbutton (START, FWD, REV, SLOW, FAST) is present.


2. MOMENTARY BITS:




3. When choosing CUSTOM PARAMETER BLOCKS, there is only the default choice of CUSTOM with CONSULTATION as the customer is requesting to consult with an LV MCC Systems Engineer.

21



L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SM

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFW

D

RE

V

OL

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

L3L2L1S

TAB

(L3)

(L2)

(L1)

(T3)

(T2)

(T1)

CB

/FD

SFA

ST

SLO

W

OL1

OL2

MTR

MTR

MTR

MTR

SH

OR

T

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FWD

RE

V

11A

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

M1

1A

X2

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

(A1)

(A2)

(6)

(7)

(1)

(2)

(8)

(3)

(9)

(T1)

(10)

(T2)

(4)

(5)

(SP

E)

IN1

IN2

IN3

IN4

=24V

PW

R

CO

MS

B L U E W I R EOU

T1

OU

T2

OU

T3

OL

FAS

T

SLO

W

11A

X2

SH

OR

T

HA

ND

OFF

AU

TO

X

X

FWD

RE

V

STO

P

HA

ND

OFF

AU

TO

X

X

STA

RT

STO

P

HA

ND

OFF

AU

TO

X

X

SLO

W

FAS

T

STO

P

HA

ND

OFF

AU

TO

X

X

SLO

W

FAS

T

STO

P

Figure 8

Published by Siemens Industry, Inc. 2017.

Siemens Industry, Inc. 7000 Siemens Road Wendell, North Carolina 27591

For more information, please contact our Customer Support Center. Phone: +1 (800) 333-7421

www.usa.siemens.com/mcc

Article No. EMMS-T40097-00-4AUS Printed in U.S.A. © 2017 Siemens Industry, Inc.

The technical data presented in this document is based on an actual case or on as-designed parameters, and therefore should not be relied upon for any specific application and does not constitute a performance guarantee for any projects. Actual results are dependent on variable conditions. Accordingly, Siemens does not make representations, warranties, or assurances as to the accuracy, currency or completeness of the content contained herein. If requested, we will provide specific technical data or specifications with respect to any customer’s particular applications. Our company is constantly involved in engineering and development. For that reason, we reserve the right to modify, at any time, the technology and product specifications contained herein.

Documents

SIMOCODE pro - Siemens Guide usa.siemens.com/mcc SIMOCODE pro ... This is a specific selection as to how SIMOCODE pro is placed ... (Cyclic Receive Bit 0.5) sets SIMOCODE pro …