Signature Overview• Handmade in America – Family owned factory, just outside Atlanta, GA

– Each piece is made by one craftsman and signed by that craftsman. (not assembly line)– Lifetime Warranty– All cases are constructed from ¾” furniture grade plywood.

• Plywood is Purebond – Formaldehyde Free– Face Frames are ¾” solid maple. – Doors and Drawers are inset, not overlay. (Furniture vs Cabinetry)– Drawer Boxes are all dovetailed, Solid 5/8 Maple with fully captive bottom.– Legs are solid maple milled by hand– Bottoms are “dadoed” into the cabinet. Sides are notched for bottoms– Doors are 5 piece mortise and tennon construction with Solid Maple panels– Interiors are finished to match exterior– Finish is low VOC lacquer and varnish – high moisture resistance– All finishes are glazed by hand – not a mass produced looking finish– Soft closing hardware on drawers and doors.

• Door soft close mechanism is now integrated into the hinge– Fits industry standard Granite/Marble tops– Fits K2210

Signature Furniture vs Cabinets

1 9 Ply Furniture Grade Plywood for s ides and bottoms Chip core, Particle Board, MDF, Construction

Always 3/4" thick Plywood is an upgrade in some cases . Mostly 5/8"

2 Des igned as freestanding furni ture pieces Bas ic Boxes with doors on the front

3 We have des igns They have door s tyles

Al l bottoms are dadoed and glued into the s ides Connect bottoms with nai l s from the outs ide or doweled

4 Use ful ly integrated sol id wood legs top to bottom stick feet under boxes and ca l l them legs

5 Li fetime Guarantee ?

Made one at a time just for you. High production runs of boxes . Change door s tyles

6 Insta l lation- Everything i s a l ready done. Just put into Multiple boxes must be put in proper place,

place and hook up the plumbing. attach to one another, add fi l lers to create des i red

width, cut crown to fi t, insta l l crown, touch up crown

after insta l l , etc.

7 1/4" plywood backs are dadoed into the case and attached 1/8" mdf back i s s tapled on from the back. Offers no added

with screws support

8 Use Sol id wood Back Braces and 3/4" plywood internal supports Use plywood "hanging s trips" and plastic corner braces

9 Apply glazes by hand with a brush by ski l led artists Apply glazes on production l ine with glue bottles and

This not only appl ies glaze to the cracks but gives the fi nish a pointed tips . Not worked by hand.

"patina" that can't be created in a mass production environment.

Interiors are finished to match exteriorDrawer boxes are solid maple, dovetailed and have soft profile applied to top edgeHand applied finishes

Details

6 Designs

11 Sizes

3 Base Options for 2 Styles

Bracket Wedge Bun

Available Finishes

7 Standard Finishes Available

New Introductions Summer 2011

7 New Paint Finishes

New Introductions Summer 2011

Ethan - 270

-Same size options as Vaughan and Nolan

New Introductions Summer 2011

Linen Towers

-Available in each style-Base is matched to accompanying vanity base-Door style matches vanity style-3 Adjustable shelves in upper section-2 Adjustable shelves in lower section-Optional Hamper upgrade available

New Introductions Summer 2011

Wall Hung Versions

-Available in each style-Overall height is 18”

Shown: 140-0542 Wall Hung River

New Introductions Summer 2011

Stone Top Program

-4 colors-White Carrara-Black Granite-Beige -Emperador

-Precut for Signature Sink – Not 2210-White and Linen Sinks available-3 holes for 8” widespread-All tops are 1” thick except Black (3/4)-Backsplash Included-Eased edge on all three sides-25,31,37,48,60dbl