Si5xx-PROG-EVB User's Guide

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.comRev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021

Si5xx/514/570-PROG-EVB

Si514/570/571/598/599 ANY-FREQUENCY I2CPROGRAMMABLE XO/VCXO EVALUATION BOARD

Description

The Skyworks Si514/570/571/598/599 evaluation kitcontains the hardware and software needed forevaluation of the Si514/570/571/598/599 Any-Frequency I2C programmable XO/VCXO and can berun on a USB-equipped PC.

Features

Evaluation of Skyworks' Si514/570/571/598/599 Any-Frequency I2C programmable XO/VCXO

Windows-compatible software control and device programming

Voltage regulator supports device operation of the Si5xx at +1.8, +2.5, or +3.3 V

I2C communication options are jumper configurable Voltage control (VC) input port (Si571/Si599)

Functional Block Diagram

LevelTranslator

J16

VDD

OutputConditioner

J14

J18GND

CLKP

CLKN

SDA (VC)

SCL (OE)

1

2

3

6

5

4

CLKP

CLKN

8

7

TP4

J13

LevelTranslator

OutputEnable

VDDREG

J11

TP3(VDD_DUT)

Manual VDDVoltage Select

4-3=2.5V2-1=3.3V OPEN=1.8V

1

3

2

4

USB

C8051F342MCU

TP2(VBUS_5V)

J2

OptionalPower In

J5

1 2 3

RE

GIN

TP1(EXT3P3V)

Filter

J12

J1

TP10

1

2

3TP6

(SCL)TP7

(SDA)

J19

J17

J20

1

2

1

2

1

2

3

1

2

3

VCO In

DUT

NC

(S

CL

)N

C (

SD

A)

2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.comRev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021

1. IntroductionThis document describes the operation of the Skyworks Si514/570/571/598/599 evaluation kit. The Si5xx-PROG-EVB kit refers to the evaluation board hardware and software intended for customer evaluation of theSi514/570/571/598/599 Any-Frequency I2C programmable XO/VCXO. The Si5xx-EVB kit contains the following: Si5xx-PROG-EVB Hardware Programmable Oscillator Software EVB Driver (USBXpress®)The software components run on a USB-equipped PC and are described in detail in Section “5. Software Guide” The Si5xx-PROG-EVB evaluation board can be used to evaluate the Si514, Si570, Si571, Si598, and Si599 I2Cprogrammable XOs or VCXOs as shown in Table 1. The Si514-PROG-EVB evaluation board can be used toevaluate the Si514 I2C-programmable XO as shown in Table 1. This evaluation board functions and performssimilar to the Si5xx-PROG-EVB evaluation board.

Table 1. Si5xx XO and VCXO Device Evaluation Board Selector Guide

Ordering Part # Type Devices Supported

Packages Supported

Output Format, Temp Stability, Tuning Slope

Supported Frequency

Range

Si5xx-EVB Single/Dual Frequency XO/VCXO Eval Board

Si510/511 Si512/513 Si515/516 Si530/531 Si532/533 Si550/552Si590/591

5 x 7 mm, 6-pin 3.2 x 5 mm, 6-pin 3.2 x 5 mm, 4-pin

Any 100 kHz to1417 MHz

Si5xx-PROG-EVB I2C Programmable XO/VCXO Eval Board

Si514Si570/571Si598/599

5 x 7 mm, 8-pin 5 x 7 mm 6-pin

3.2 x 5 mm, 6-pin

Any 100 kHz to1417 MHz

Si514-PROG-EVB I2C Programmable XO Eval Board with sol-

dered Si514

Si514 5 x 7 mm 6-pin Any 100 kHz to250 MHz

Si5xx5x7-EVB Quad Frequency XO/VCXO Eval Board

Si534Si554

5 x 7 mm, 8-pin Any 10 to 1417 MHz

Si570-PROG-EVB I2C Programmable XO Eval Board with sol-

dered Si570

Si570 5x7 mm 8-pin Any 10 to 1417 MHz

Notes:1. Si5xx samples must be ordered separately from the Si5xx-PROG-EVB.2. Board must be modified to be consistent with the ordered part. See "3.10. Output Terminations" on page 8.3. Si514-PROG-EVB comes with an Si514 preinstalled.

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 3Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021

1.1. Quick Start1. Install an Si514, Si570, Si571, Si598, or Si599 device on the board (Si514-PROG-EVB comes with an Si514

preinstalled; the Si570-PROG-EVB also comes with an Si570 installed).2. Verify that the jumper settings are correct.3. Connect the USB cable from the EVB to the host PC.4. Install the Programmable Oscillator Software and driver.5. Launch the Programmable Oscillator Software by clicking Start Programs Skyworks Programmable

Oscillator Software. Click on one of the shortcuts in the group.


2. Top/Bottom Views of Board

Figure 1. Board Views (a) Top; (b) Bottom(b)

StatusLEDs


3. Functional DescriptionThe Si5xx-PROG-EVB is the evaluation board assembly for the Si514/570/571/598/599 Any-Frequency I2CProgrammable XO/VCO. This evaluation board assembly provides access to all signals for programming andoperating the device. The Si5xx-PROG-EVB schematics, bill of materials, and PCB layouts are included assections 6, 7, and 8, respectively. Figure 2 provides a block diagram for the board.

Figure 2. Si5xx-PROG-EVB Functional Block Diagram

LevelTranslator

J16

VDD

OutputConditioner

J14

J18GND

CLKP

CLKN

SDA (VC)

SCL (OE)

1

2

3

6

5

4

CLKP

CLKN

8

7

TP4

J13

LevelTranslator

OutputEnable

VDDREG

J11

TP3(VDD_DUT)

Manual VDDVoltage Select

4-3=2.5V2-1=3.3V OPEN=1.8V

1

3

2

4

USB

C8051F342MCU

TP2(VBUS_5V)

J2

OptionalPower In

J5

1 2 3

RE

GIN

TP1(EXT3P3V)

Filter

J12

J1

TP10

1

2

3TP6

(SCL)TP7

(SDA)

J19

J17

J20

1

2

1

2

1

2

3

1

2

3

VCO In

DUT

NC

(S

CL

)N

C (

SD

A)


3.1. Power SupplyThe Si5xx-PROG-EVB is pre-configured to accept 5 V from the USB connector at J2. The DUT is powered fromthe VDD regulator by default, but could be changed to an external supply introduced through J1. To do this, simplymove jumper J11 from pins 2-3 to 1-2 and apply power to J1. (Ensure the voltage range of the DUT is obeyed, andit is also good practice to set a current limit on the power supply). It is also possible for the microcontroller (U9) to adjust the VDD regulator through the software. The microcontrollerhas pull-downs configured at P0.0 and P0.1 that grounds R18 and R19, respectively, adjusting VDD_DUT to 1.8,2.5, or 3.3 V. It is also possible to install jumpers in J5 to manually force a VDD_DUT voltage. Table 2 illustrates thesettings of J5:

3.2. Reset CircuitThe Si5xx-PROG-EVB MCU may be reset by momentarily pressing pushbutton SW1.

3.3. USBA 4-pin USB receptacle is provided at location J2. The Si5xx-PROG-EVB is compatible with USB Specification 2.0.When the USB link is in use, the MCU drives LED D4.

3.4. MCUThe Skyworks MCU, P/N C8051F342, provides the following functions:

Supports I2C communication to the DUT on behalf of the host PC per the Programmable Oscillator Software Drives a number of status indicator LEDs (see Table 3) Supplies 3.3 V to peripheral ICs on the motherboard but not to the DUT Controls DUT power (see Section “3.1. Power Supply” ) Auto-detects the part type (e.g., Si51x/Si57x/Si59x)There is a provision for in-circuit programming at connector J4. This provision should not be needed in normaloperation. The host PC operates the software and communicates to the Si5xx-PROG-EVB through the MCU viaUSB connector J2. When the USB link is in use, LED D4 should flash. The MCU may be reset by momentarilypressing pushbutton (SW1).

Table 2. J5 settings for VDD_DUT

Jumper VDD_DUT

Open 1.8 V

1–2 3.3 V

3–4 2.5 V


3.5. Status SignalsThere are four LEDs on the Si5xxPROG-EVB that report visual status as listed in Table 3 and shown in Figure 1b.Upon powerup, D1 should be illuminated.

3.6. JumpersThere are seven jumper locations on the Si5xx-PROG-EVB as listed in Table 4. The default or pre-loaded jumpersare shown in Figure 1a.

Table 3. Si5xx-PROG-EVB LEDs

LED ON OFF

D1 VDD3p3 volts is present VDD3p3 volts is NOT present

D2 Ext3p3V volts is present Ext3p3V volts is NOT present

D3 Reserved Reserved

D4 USB access in progress No USB access in progress

Table 4. Si5xx-PROG-EVB Jumpers

Jumper Block Reference Function

J5 Manual (on-board) VDD_DUT adjust (see Table 1)

J11 VDD_DUT select: 1-2: External voltage (from J1) 2-3: On-board regulator

J13 I2C/Vc selector: 1-2: I2C communication 3-4: Ext Vc input (Si57x)

J16 Output enable (Si57x): 1-2: OE is HIGH 3-4: OE is LOW

J17 Manual shutdown of I2C port for Si514 (also control-lable via SW)

J19 Manual shutdown of I2C port for Si57x (also control-lable via SW)

J20 I2C communication access port 3-4: SCL connection to MCU 5-6: SDA connection to MCU


3.7. External I2C Communication It is possible to use an external I2C controller to communicate with the DUT. To do this, remove the jumpersinstalled in J20 and connect the external I2C harness to J20. Grounded pins (1-2, 7-8) are there for grounding theharness. Pins 4 and 6 can be driven as SCL and SDA, respectively.

3.8. Si5xx-PROG-EVB Digital Control SignalOne normally static digital input control signal routes to the Si5xx: Output Enable or OE. By default, the OE signalis pulled HIGH on the Si5xx-PROG-EVB and may be pulled low by installing a jumper at J16.

3.9. Si5xx-PROG-EVB Voltage Control SignalAn external voltage control signal may be applied to the control voltage modulation input at the J12 header(VCO_IN). This voltage supplies the control voltage or voltage modulation input to the DUT. J13 should be installedin the 2-3 position.

3.10. Output TerminationsThe Si5xx-PROG-EVB can support four different output formats: CMOS, LVPECL, LVDS, and HCSL. There areoutput resistors that are needed to accompany each format. Table 5 shows which resistors are needed for eachoutput:

Table 5. Output Termination Installation Definition

Output Format

R36 R40 R35 R44 R37 R38 R29 R34 R43 R45

CMOS 10 10 NP NP NP NP NP NP NP NP

LVPECL 0 0 130 130 NP NP NP 0 NP 0

LVDS 0 0 NP NP NP NP NP NP NP NP

HCSL 0 0 NP NP NP NP NP NP NP NP


4. Configuring the Si5xx-PROG-EVB

Figure 3. Si5xx-PROG-EVB Typical Configuration

Si5xx-EVB

1.8-3.3V Power Supply(Optional) +-

Optional Voltage Source(for Si571)

+-

+-

+-

Optional Oscilloscope or other Instrument

Frequency Counter

CLKN

CLKP

VC

Optional I2C Device SCL/SDA

PC

USB


5. Software GuideThe evaluation kit includes software called Programmable Oscillator Software, which consists of several tools: Programmable Oscillator Calculator—Program new dividers and output frequencies in the device using large

and small frequency programming procedures. This can run with or without an EVB connected to the computer. Register Programmer—Program individual registers on the oscillator device on the EVB. Si57x/9x Register Programmer—Program Si570/571/598/599 specific registers. Register Viewer—View all the register values on the oscillator installed on the EVB. User Guide—Read more help information on using the software. Spreadsheet Finder for HS_DIV and N1—Use an Excel spreadsheet to find the Si570/571/598/599 dividers.

No EVB is required.

5.1. Programmable Oscillator Software InstallationThe following sections describe how to install and use the software. There is a readme.txt file with the installation files as well as a software user guide installed with the software.

5.2. System Requirements Microsoft Windows® 2000, XP, Vista, 7 USB 2.0 2 MB of free hard drive space 1024 x 768 screen resolution or greater Microsoft .NET Framework 1.1 USBXpress 3.1.1 driverNote: USBXpress 3.1.1 driver is provided and installed with the software. Newer or older versions of USBXpress available

from other EVB kits or online have not been tested with this software.

5.3. Microsoft .NET Framework InstallationThe Microsoft .NET Framework is required before installing and running the software. Details and installationinformation about the .NET Framework are available via a shortcut in the NETFramework directory or at thefollowing web site: www.microsoft.com/downloads/details.aspx?FamilyId=262D25E3-F589-4842-8157-034D1E7CF3A3&displaylang=enThere are multiple versions of the .NET Framework available from Microsoft, and they can be installed side-by-sideon the same computer. The software requires Version 1.1 but can run under other versions. Contact your systemadministrator for more details.

5.4. Programmable Oscillator Software InstallationThe Programmable Oscillator Software is installed from the ProgOscSwInstall.exe file.1. Double-click the install file to start the wizard.2. Follow the wizard instructions to complete the installation for both the software and the driver. Use the default

installation location for best results.3. After the installation is complete, click on Start Programs Skyworks Programmable Oscillator Software.

Select one of the items in the menu including the User Guide to get more details on how to run the software.

5.5. Programmable Oscillator Software Uninstall Close all the programs and help files before running the uninstaller to ensure complete removal of the software. Touninstall the software, use the Add and Remove Programs utility in the Control Panel or click Start Programs Skyworks Programmable Oscillator Software Uninstaller.Note: The driver software must be uninstalled separately.

http://www.microsoft.com/downloads/details.aspx?FamilyId=262D25E3-F589-4842-8157-034D1E7CF3A3&displaylang=en

Skyw

orks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyw

orksinc.com • w

ww

.skyworksinc.com

11R

ev. 0.3 • Skyworks Proprietary Inform

ation • Products and Product Information are Subject to C

hange Without N

otice • October 12, 2021

6. Schematic

VCO in

VDDOK

OptionalPOWER IN

VDD5V OK

In-CircuitProgrammingConnector

4-3 = 2.5V2-1 = 3.3VOPEN = 1.8VVout = 1.25*(1+Rtop/Rbot)

.5% .5%.5%

CLKO

CLKOB

3) Install for VCOs4) 100 OHM Diff. Impedance, 50 OHM to GND

2) Mount close to pins 1 & 2 of the DUT

Notes:

1) Mount close to DUT

Note 3

Note 1

NOTE 4

Sprinkle around DUT

Output Resistor Configurations for VariousOutput Formats (R in Ohms)

OutputFormat

CMOSLVPECL

LVDS

HCSL

- NP = No Pop

10

0

0

R36 R40 R35 R44 R37 R38 R29 R34 R43 R45

10 NP NP NP NP NP NP NP NP

0 130 130 NP NP NP NP

0 NP NP NP NP NPNP

0 0

NP NP NP NP NP NP NP NP

NP NP

Note 3

(No Pop)

(No Pop)

(No Pop)

(No Pop)

(No Pop)

(No Pop)

OutputEnable

DisablePins 1&2Com.

DisablePins 7&8Com.

0 0

PWR_SEL1PWR_SEL2

VC_Filter

MCU_RSTNMCU_C2CK

MCU_C2CK

VDD_MID

SDASCL

Board_ID

VDD_MID

Board_ID

VC_Filter

SDA

SCL

EN1EN2

EN1

EN2

Brd_Cnfg0Brd_Cnfg1Brd_Cnfg2

Brd_Cnfg7Brd_Cnfg6

Brd_Cnfg3Brd_Cnfg4Brd_Cnfg5

Brd_Cnfg1Brd_Cnfg2Brd_Cnfg3Brd_Cnfg4Brd_Cnfg5Brd_Cnfg6Brd_Cnfg7

Brd_Cnfg0

VDD3P3

Ext3p3V

VDD3P3

VDD3P3

VDD3P3

VDD_DUTVBUS_5V

VDD_DUT

VDD_DUT

VBUS_5V

VBUS_5V

VDD_DUTVDD_DUT Ext3p3V

VDD_DUT

VBUS_5V

R1127R1127

R26

0 oh

mR

260

ohm

C13

100N

C13

100N

C74.7uFC74.7uF

R198.25KR198.25K

J8J8

1

R9

1K

R9

1K

TP3TP3

1

R2127R2127

J17J17

12

C22200pFC22200pF

AC

D4

Red

AC

D4

Red

21

C14100NC14100N

TP7TP7

1C6100NC6100N

R1817.4KR1817.4K

+ C433UF

+ C433UF

J11J11

123

U7

Si514_70_71

PIN Labling:()=570 or 571,514 othrwz

U7

Si514_70_71

PIN Labling:()=570 or 571,514 othrwz

SDA(Vc)1

SCL(OE)2

GND3

CLKP4

CLKN5

VDD6

NC

(SD

A)

7N

C(S

CL)

8

C245pFC245pF

J16J16123

TP5TP5

1

R450

ohm

R450

ohm

R1722.6K

R1722.6K

J20J20

1 23 45 67 8

R3749.9R3749.9

R144.99KR144.99K

R749.9R749.9

R50 ohmR50 ohm

C111UF

C111UF

R28200KR28200K

R11

1K

R11

1K

TP4TP41

TP8TP8

1

R27

0 oh

mR

270

ohm

C154.7uFC154.7uF

J4J4

12345679

810

R3301R3301

C1

100N

C1

100N

R134.99K

R134.99K

C12100NC12100N

R20

0 oh

mR

200

ohm

U8

PCA9306

U8

PCA9306

GND

1

VREF1

2

SCL13

SDA14

SDA25

SCL26

VREF2

7

EN8

U4

MIC5301

U4

MIC5301

Vin1

GND

2

EN3

ADJ4

Vout5

TP6TP6

1

J5J5

1234

R12 10R12 10

R22

0 oh

mR

220

ohm

J6J6

1

R422.2KR422.2K

SW1NOSW1NO

1243

R432KR432K

C17

100N

C17

100N

TP1TP1

1

TP10TP10

1

R46 0 ohmR46 0 ohm

C16

100N

C16

100N

R412.2KR412.2K

U1 SP0503BAHTU1 SP0503BAHT

1

23

4

C21

100N

C21

100N

R47 0 ohmR47 0 ohmR332.2KR332.2K

R3849.9R3849.9

R39200KR39200K

U6

PCA9306

U6

PCA9306

GND

1

VREF1

2

SCL13

SDA14

SDA25

SCL26

VREF2

7

EN8

TP9TP9

1

R44130R44130

+ C333UF

+ C333UF

J12J12

123

R24

0 oh

mR

240

ohm

C20

100N

C20

100N

R340 ohm

R340 ohm

C23

100N

C23

100N

R80 ohmR80 ohm

C185pFC185pF

C8

2200pF

C8

2200pF

J2

USB

J2

USB

V1

Gnd

4

D-

2

D+

3

S15

S26

J19J19

12

R23

0 oh

mR

230

ohm

R16

4.99K

R16

4.99K

AC

D3

Red

AC

D3

Red

21

TP2TP2

1

R4301R4301

R31

4.99

K

R31

4.99

K

R10

1K

R10

1K

**

J1

**

J1

1

2

R322.2KR322.2K

C22

100N

C22

100N

J18J18

1

32 4 5

J13J13

123

L2L2

1 2

Ser No.

U5

DS2411

Ser No.

U5

DS2411

Vcc

6G

ND

1

I/O2

NC13

NC24

NC35

R21

0 oh

mR

210

ohm

R40

0 ohm

R40

0 ohm

R1510K

R1510K

C261UFC261UF

R25

0 oh

mR

250

ohm

R292KR292K

AC

D2

Grn

AC

D2

Grn

12

C25100NC25100N

C522pFC522pF

C9100NC9100N

C19100N

C19100N

R35130R35130

J9J9

1

J14J14

1

32 4 5

R6 100R6 100

L1L1

1 2

J10J10

1

R30

4.99

K

R30

4.99

K

AC

D1

Grn

AC

D1

Grn

12

C104.7uFC104.7uF

U9

C8051F342

U9

C8051F342

P0.11 P0.02

GN

D3

D+4

D-5

VD

D6

RE

GIN

7

VBUS8

RST/C2CK9

P3.0/C2D10

P2.711

P2.612

P2.513

P2.414

P2.315

P2.216

P2.117

P2.018

P1.719 P1.620 P1.521 P1.422 P1.323 P1.224 P1.125 P1.026

P0.727 P0.628 P0.529 P0.430 P0.331 P0.232

R36

0 ohm

R36

0 ohm

J7J7

1

Figure 4. Si5xx-PROG-EVB (Universal I2C XO/VCXO)


7. Bill of Materials

Table 6. Si5xx-PROG-EVB/Si514-PROG-EVB/Si570-PROG-EVB Bill of Materials1

Item Qty Reference Value Mfr Manufacturer PN PCB Footprint

1 14 C1,C6,C9,C12,C13,C14,C16,C17,C19,C20,C21,C22,C23,

C25

100 nF Venkel C0603X7R160-104KNE SM_C_0603

2 2 C2,C8 2200 pF Venkel C0603X7R160-222KNE SM_C_0603

3 2 C3,C4 33 µF Venkel TA006TCM336KBR EIA 3528

4 1 C5 22 pF Venkel C0603C0G500-220KNE SM_C_0603

5 3 C7,C10,C15 4.7 µF Venkel C0805X5R6R3-475KNE SM_C_0805

6 2 C11,C26 1 µF Venkel C0603X7R6R3-105KNE SM_C_0603

7 2 D1,D2 Grn Panasonic LN1371G LED_gull

8 2 D3,D4 Red Lumex LN1271RAL LED_gull

9 1 J1 Phoenix_2_screw Phoenix MKDSN 1.5/2-5.08 Phoenix2pin-M_p2pitch

10 1 J2 USB FCI 61729-0010BLF USB_typeB

11 1 J4 5by2_Shrd_Hdr_SMT Sullins PPTC052LJBN-RC 5by2head-er_thruhole

12 1 J5 2by2_M_Hdr Sullins PBC36DAAN 2by2head-er_p1pitch

13 5 J6,J7,J8,J9,J10

Jmpr_1pin Tyco 87224-1 1by1header_TH

14 4 J11,J12,J13,J16

Jmpr_3pin Tyco 146225-3 3pin_p1pitch

15 2 J14,J18 SMA_VERT Johnson 142-0701-211 SMA_VERT

16 2 J17,J19 Jmpr_2pin Sullins PBC36DAAN 2by2head-er_p1pitch

17 1 J20 4X2 Header Sullins PBC04DFAN 4by2head-er_p1pitch

18 2 L1,L2 Ferrite Murata BLM31A601S 1206

19 2 R1, R2 127 Venkel CR0603-16W-1270FT SM_R_0603

Notes:1. Outputs configured for LVPECL.2. Si514-PROG-EVB contains a presoldered 514CBA000118AAG device.3. Si570-PROG-EVB contains a presoldered 570ACA000118DG.


20 3 R3,R4 301 Venkel CR0603-16W-3010FT SM_R_0603

21 16 R5,R8,R20,R21,R22,R23,R24,R25,R26,R27,R34,R36,R40,R45,R46,

R47

0 Venkel CR0603-16W-000T SM_R_0603

22 1 R6 100 Venkel CR0603-16W-1000FT SM_R_0603

23 1 R7 49.9 Venkel CR0603-16W-49R9FT SM_R_0603

24 3 R9,R10,R11 1 k Venkel CR0603-16W-1001FT SM_R_0603

25 1 R12 10 Venkel CR0603-16W-10R0FT SM_R_0603

26 1 R15 10 k Venkel CR603-16W-1002FT SM_R_0603

27 5 R13,R14,R16,R30,

R31

4.99 k Venkel CR0603-16W-4991FT SM_R_0603

28 1 R17 22.6 k Venkel CR0603-16W-2262FT SM_R_0603



31 2 R28,R39 200 k Venkel CR0603-16W-2003FT SM_R_0603

32 4 R32,R33,R41,R42

2.2 k Venkel CR0603-16W-2201FT SM_R_0603

33 2 R35,R44 130 Venkel CR0603-16W-1300FT SM_R_0603

34 1 SW1 NO Mountain Switch

101-0161-EV 4pinSwitch

35 2 TP1,TP10 Test Point Key Stone 5001K .035" TH

36 1 U1 SP0503BAHT Little Fuse SP0503BAHT SOT143

37 1 U4 MIC5301 Micrel MIC5301YD5 SOT23-5

38 1 U5 DS2411 Maxim/Dallas

DS2411RP+ TSOC-6

39 2 U6,U8 PCA9306 TI PCA9306DCTR PSOP

40 1 U9 C8051F342 Skyworks C8051F342-GQ LQFP-32

Table 6. Si5xx-PROG-EVB/Si514-PROG-EVB/Si570-PROG-EVB Bill of Materials1 (Continued)




Not Populated

412 U7 Si514_70_71 Skyworks

42 R29,R43 2 k Venkel CR0603-16W-2001FT SM_R_0603

43 C18,C24 5 pF Venkel C0603X7R160-104KNE SM_C_0603

44 R37,R38 49.9 Venkel CR0603-16W-49R9FT SM_R_0603

45 TP2,TP3,TP4,TP5,TP6,TP7,TP8,TP9

Test Point Key Stone 5001K .035" TH

Part Order Code 514CBA000118AAGType I2C Programmable

Package 5x7 mm, 6-PinOutput CMOS

Frequency Range 0.10–212.5 MHzStarting Frequency 156.25 MHz

VDD 3.3 VTemperature Stability ±25 ppm

Total Stability ±50 ppmOpening Temperature Range –40 to 85 °C

Data Sheet www.skyworksinc.com/support-ia

Part Order Code 570ACA000118DGType I2C programmable

Package 5x7 mm, 8 pinOutput LVPECL

Frequency Range 10–945, 970–1134, 1213–1417.5 MHzStarting Frequency 156.25 MHz

VDD: 3.3 VVDD 3.3 V

Total Stability 20 ppmOpening Temperature Range –40 to 85 °C

Data Sheet www.skyworksinc.com/support-ia

Table 6. Si5xx-PROG-EVB/Si514-PROG-EVB/Si570-PROG-EVB Bill of Materials1 (Continued)




8. Layout

Figure 5. Primary Side

Figure 6. Layer 2: PWR


Figure 7. Layer 3: GND

Figure 8. Secondary Side


DOCUMENT CHANGE LISTRevision 0.1 to Revision 0.2 Added ordering information and revised text to add the Si514-PROG-EVB to the list of released EVBs. Updated Table 5 on page 8. Updated Figure 4 on page 11 (schematic). Updated "7. Bill of Materials" on page 12 and notes.

Described changes needed for the Si514-PROG-EVB.

Revision 0.2 to 0.3 Added ordering information and revised test for the newly released Si570-PROG-EVB


NOTES:

Copyright © 2021 Skyworks Solutions, Inc. All Rights Reserved.Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.

No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks’ Terms and Conditions of Sale.

THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.

Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of Skyworks’ published specifications or parameters.

Skyworks, the Skyworks symbol, Sky5®, SkyOne®, SkyBlue™, Skyworks Green™, Clockbuilder®, DSPLL®, ISOmodem®, ProSLIC®, and SiPHY® are trademarks or registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names are for identification purposes only and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.

Portfoliowww.skyworksinc.com/ia/timing

SW/HWwww.skyworksinc.com/CBPro

Qualitywww.skyworksinc.com/quality

Support & Resourceswww.skyworksinc.com/support

ClockBuilder ProCustomize Skyworks clock generators, jitter attenuators and network synchronizers with a single tool. With CBPro you can control evaluation boards, access documentation, request a custom part number, export for in-system programming and more!

www.skyworksinc.com/CBPro

Skyworks Solutions, Inc. | Nasdaq: SWKS | [email protected] | www.skyworksinc.comUSA: 781-376-3000 | Asia: 886-2-2735 0399 | Europe: 33 (0)1 43548540 |

www.skyworksinc.com/ia/timing

www.skyworksinc.com/CBPro

www.skyworksinc.com/quality

www.skyworksinc.com/support

Documents

Si5xx-PROG-EVB User's Guide