7/21/2019 Ship design project Engine spec

1/4

MAN B&W 5.02

Page of 4

MAN DieselMAN B&W S60MC-C7 198 57 80-8.0

Space Requirement

Normal centre line distance for twin engine instal-

lation: 6,250 mm.

The dimensions are given in mm, and are for

guidance only. If the dimensions cannot be

fullled, please contact MAN Diesel or our local

representative.

Fig. 5.02.01a: Space requirement for the engine, turbocharger on exhaust side (4 59 122)

178 32 81-8.2

7/21/2019 Ship design project Engine spec

2/4

MAN B&W 5.02

Page 2 of 4

MAN DieselMAN B&W S60MC-C7 198 57 80-8.0

Cyl. No. 5 6 7 8

A

min. 7,22 8,42 9,62 0,82 Fore end: A minimum shows basic engine

A maximum shows engine with built-on tuning wheelFor PTO: See corresponding space requirementmax. 7,597 8,67 9,637 0,657

B

4,850 4,850 4,850 5,00 MAN Diesel TCA The required space to the engine room casing includes

mechanical top bracing4,280 4,680 4,680 5,00 ABB TPL

4,590 4,590 5,00 5,00 Mitsubishi MET

C

3,787 3,887 4,087 4,566 MAN Diesel TCA Dimensions according to turbocharger choice at

nominal MCR3,52 3,727 3,927 4,404 ABB TPL

3,546 3,77 4,029 4,334 Mitsubishi MET

D 3,705 3,780 3,820 3,890The dimension includes a cofferdam of 600 mm and must full minimum

height to tank top according to classication rules

E 9,725The minimum distance from crankshaft centre line to lower edge of deck

beam, when using MAN B&W Double Jib Crane

F0,725 Minimum overhaul height, normal lifting procedure

9,975 Minimum overhaul height, reduced height lifting procedure

G 3,400 See Engine Top Bracing, if top bracing tted on camshaft side

H

7,045 7,045 7,045 7,045 MAN Diesel TCA Dimensions according to turbocharger choice at

nominal MCR6,582 6,700 6,700 6,886 ABB TPL

6,760 6,760 7,005 7,005 Mitsubishi MET

J 345 Space for tightening control of holding down bolts

K See textK must be equal to or larger than the propeller shaft, if the propeller shaft is

to be drawn into the engine room

V 0, 5, 30, 45, 60, 75, 90Maximum 45 when engine room has minimum headroom above the

turbocharger

Fig. 5.02.01b: Space requirement for the engine

7/21/2019 Ship design project Engine spec

3/4

MAN B&W 5.02

Page 3 of 4

MAN DieselMAN B&W S60MC-C7 198 57 80-8.0

Normal centre line distance for twin engine instal-

lation: 6,250 mm.

The dimensions are given in mm, and are for

guidance only. If the dimensions cannot be

fullled, please contact MAN Diesel or our localrepresentative.

Fig. 5.02.02a: Space requirement for the engine, turbocharger on aft end (4 59 124)

178 32 83-1.2

7/21/2019 Ship design project Engine spec

4/4

MAN B&W 5.02

Page 4 of 4

MAN DieselMAN B&W S60MC-C7 198 57 80-8.0

Cyl. No. 5 6 7 8

A

min. 7,22 8,42 9,62 0,82 Fore end: A minimum shows basic engine

A maximum shows engine with built-on tuning wheelFor PTO: See corresponding space requirementmax. 7,597 8,67 9,637 0,657

B 2,850

MAN Diesel TCAThe required space to the engine room casing includes

top bracingABB TPL

Mitsubishi MET

C

4,32 4,450 4,725 5,279 MAN Diesel TCA Dimensions according to turbocharger choice at

nominal MCR4,046 4,290 4,565 5,7 ABB TPL

4,07 4,334 4,667 5,047 Mitsubishi MET

D 3,705 3,780 3,820 3,890The dimension includes a cofferdam of 600 mm and must full minimum

height to tank top according to classication rules

E 9,725The minimum distance from crankshaft centre line to lower edge of deck

beam, when using MAN B&W Double Jib Crane

F0,725 Minimum overhaul height, normal lifting procedure

9,975 Minimum overhaul height, reduced height lifting procedure

G 3,400 See Engine Top Bracing, if top bracing tted on camshaft side

H

7,684 7,684 7,684 7,684 MAN Diesel TCA Dimensions according to turbocharger choice at

nominal MCR7,000 7,234 7,234 7,535 ABB TPL

7,05 - 7,350 7,350 Mitsubishi MET

I

2,355 2,355 2,355 2,355 MAN Diesel TCA Dimensions according to turbocharger choice at

nominal MCR2,50 2,280 2,280 2,463 ABB TPL

2,387 - 2,425 2,425 Mitsubishi MET

J 345 Space for tightening control of holding down bolts

K See text K must be equal to or larger than the propeller shaft, if the propeller shaft isto be drawn into the engine room

L 3,287 3,287 4,287 4,287 Space for air cooler element overhaul

N 2,450

The distances cover required space and hook travelling width for

turbocharger TCA88

O 2,234

R 2,272

S 2,229

V 0, 5, 30, 45, 60, 75, 90Maximum 30 when engine room has minimum headroom above the

turbocharger

Fig. 5.02.02b: Space requirement for the engine